SPECIAL REPAIR TO BLDG NO TS-436, TS-446, TS-494 AND TS-649 AT NAGROTA.

Amount

Schedule 'A' Part-I (B&R and Misc Work)

S & F prepainted galvatume zluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof coveing/cladding to wall fixed with self tapping screws/L-type or J-type or cranked hook bolts in lieu of screw as per manufacturer instruction including dismantling of existing asbestos cement sheet, complete all as specified and directed.

S & F prepainted galvatume zluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof coveing/cladding to wall fixed with self tapping screws/L-type or J-type or cranked hook bolts in lieu of screw as per manufacturer instruction including dismantling of existing asbestos cement sheet , complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) n. exc. 1.5 sqm each and removing from site complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc 1.50 sqm each and n. exc. 4.00 sqm each and removing from site, complete all as specified and directed.

Demolition of brick work or stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facing, dressed stone work and precast concrete articles complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground levels), complete all as specified and directed.

Taking down cement plaster on brick or stone wall etc including raking out joints, hacking for key, scrubbing down with water, complete all as specified and directed.

M&L for mild steel framed work as in roof trusses ( framed) , trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing( Beam, tee, angle, channel or flat sections ) including fabrication conforming to grade Fe 410-S including dismantling of existing, complete all as specified and directed.

S&F of framed work as in door (as in chowkats) or gates of angle or other section with guest plates rails, braces rail etc exclusive of steel sheeting or other covering hanging also fastening and fixing comforming to Fe-410-0 or Fe-310-0 including shop coat of zinc coating including preparation of surface before fixing, complete all as specified and directed.

S & F 100 mm long butt hinges, medium weight, cold rolled mild steel, complete all as specified and directed.

S & F Floor door stopper of aluminium alloy body and tongue , anodised , with hard drawn steel spring , fixed in floor , over all length of cover plate 140 mm , complete all as specified and directed.

S&F 125 mm long anodised aluminium alloy handles fabricated type , complete all as specified and directed.

S&F 300 mm mild steel oridinary rat tail rod pattern springs including roller and roller plates, complete all as specified and directed.

M&L for hold fast/clamps of mild steel stay for rain water pipes etc. confirm to Fe-290 Gde E-165, complete all as specified and directed

S & F 250 mm long aluminium alloy, anodized sliding door bolt with hasp stapple ( bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed, complete all as specified and directed.

S & F 100 mm long hasp and staple aluminium anodized with steel hinge pin including bolt to hinge plate, complete all as specified and directed.

S & F 150mm aluminium anodised barrel tower bolt of extruded section and fixed, complete all as specified and directed.

Box type steel window side hung double shutters (inside for wire mesh out side of glass) including guard bar, hinges, steel handles, tower bolt and steel peg set complete with glazing bar dovetailed or welded including a coat of red oxide after preparation of surfaces before fixing steel windows shall be conforming to relavent IS, complete all as specified and directed.

Box type steel ventilators top hung double shutters (inside for wire mesh out side of glass) including guard bar, hinges, steel handles, tower bolt and steel peg set complete with glazing bar dovetailed or welded including a coat of red oxide after preparation of surfaces before fixing steel windows shall be conforming to relavent IS, complete all as specified and directed.

S & F 35 mm thick second class hard wood factory made plain, framed, panelled shutters (two numbers of panels) with lock rail and panel of 9 mm BWP commercials ply or 12 mm veneered particle board on both faces. The size of rails and size as per IS:1003 (Part-I), Kiln seasoned & chemically pressure treated, complete all as specified and directed.

S & F 35 mm thick second class hard wood factory made glazed and skelton shutters, open rebated and prepared to receive glass, gauge, etc. (without sash bars), edges of framing plain, chamered or rounded, fitted with cut and mitred beads for securing glass, etc. Size of memebers of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) for doors, complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staple, complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.457 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staple, complete all as specified and directed.

S & F 3.00 mm thick Sheet glass ordinary quality and glazing with oil putty fixed with bends glazing pins n exc 0.5 Sqm in each pane, complete all as specified and directed.

S&F 25mm dia curtain rod aluminium brass polished with ends bulbs rings of required size including bracket, complete all as specified and directed.

M&L for Brick work with sub class 'B' (old size) bricks straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:6, complete all as specified and directed.

M&L for 100mm thick plain cement concrete 1:3:6, type C-2 (using 40mm graded crushed stone aggregate) as in sub base, complete all as specified and as directed.

M&L for 50mm thick sand filling under interlocking pavor block including watering and consolidation, complete all as specified and directed.

M&L for 80mm thick Machine pressed precast concrete interlocking pavor block any shape and size conforming to IS 15658-2006 of M-40 grade, complete all as specified and directed.

M & L for 15 mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:6, finished even and smooth without using extra cement, complete all as specified and directed.

M & L for 15 mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:4 with using WPC (WPC to be measured and paid separately) finished even and smooth without using extra cement, complete all as specified and directed.

Supply only integral water proofing compound, complete all as specified and directed.

Prepration of new or previously steel surfaces any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

Prepration of new wood or wooden based new or previously untreated surface of any description, over 10 cm width or gridth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

Preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over 2 to 3mm thick wall putty on plastered surface preparing to distempering on wall surface, complete all as specified and directed.

Complete removal of existing treatment and applying two coats of oil bound distemper over 2 to 3mm thick wall putty on plastered surface preparing to distempering on wall surface, complete all as specified and directed.

Complete removal of existing treatment of old wall surfaces and applying two coats of cement base paint, complete all as specified and directed.

Preparation of newly plastered surfaces of walls and applying two coats of cement base paint, complete all as specified and directed.

M & L for 18-20mm thick Machine cut kota stone as in floor/tread of stair case laid and jointed with grey cement slurry mixed with pigment to match the shade of the stone including grinding and polishing (mirror finish) (each stone not less than 55 cms x 55 cms) over and including 15 mm thick screed bed in CM 1:4 finished rough including roughening of existing surfaces by pick axicess and applying a coat of cement slurry @ 03 kg/Sqm of surface, complete all as specified and directed.

M & L for 18-20mm thick Machine cut kot stone slab as in skirting, dado, riser of steps/ staircase and pillar laid and jointed with grey cement slurry mixed with pigment to match the shade of the stone including grinding and polishing (mirror finish) over and including 15 mm thick rendering in CM 1:4 including taking out of existing dado, complete all as specified and directed.

M & L for 15mm thick Marble work (550 mm long x 75 mm wide strip) as in flooring, over and including 20 mm thick screed bed in CM 1:4 including poiting in white cement 1:2 using marble dust with admixture of pigments to match with white marble including rubbing, grinding and polishing, complete all as specified and directed.

M & L for 15 to 18mm thick granite stone for shelves, counter etc (table rubbed and polished) of size not less than 2 m in length over and including 20 mm thick screed bed in CM 1:4 including roughing of existing surface and applying a coat of cement slurry @ 03 kg/Sqm of surface and pointing with white cement 1:2 using marble dusts admixture of pigment of match, complete all as specified and directed.

M & L for Non-skid ceramic coloured tiles 400x400x7 mm thick as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or beddding layer in CM 1:4 and 25mm thick plain cement concrete, 1:2:4, type B-1, (using 20 mm graded crushed stone aggregate) sub base including dismentling of existing tiles , complete all as specified and directed.

M & L for Glazed ceramic coloured printed tiles (first quality) of size 450x300x7mm thick as in vertical surface, dado/skirting, over and including 15 mm thick bedding layer in CM 1:4 including dismantling of existing tiles, complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in plinth protection finished even and fiar without using extra cement, complete all as specified and as directed.

M&L for reinforced cement concrete,1:2:4, type B-1 (using 20mm graded crushed stone aggregate) as in chajjas, parapet, shelves and similar acticles, complete all as specified and directed.

M&L for PCC,1:2:4, type B-1 (using 20mm graded crushed stone aggregate) as in benching coping etc and similar items including weathering slightly rounded or chamfered angles and throating on top of chajjas rails cills etc, complete all as specified and directed.

Formwork to chajjas troughs, parpet and similar items including edges, complete all as specified and directed.

Formwork to edges of concrete flats RCC/PCC band exc 5 cm but exc 10 cm, complete all as specified and directed.

Providing number place of size 450 x 300 x 20 mm in CM 1:4 and writing building No of height 8 to 10 cms with luminous paint through grooves of size 12 x 12 mm (Base : Black, grooves : orages), complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs/blankets, any thickness including cover fillets, complete all as specified and directed.

GI T Grid system in 600 x 600 mm module which includes providing and fixing wall angle along the perimeter of the room with nylon sleeves and wooden screws at 300 mm centre to center. Suspendeding the main tee of size from the soffit, soffit cleat, rawl plugs and wire rod & leveling spring clip at 1200mm center to center cross tee, interlockined into the pre-cut slots in the main tees at 600 mm centre to center in direction perpendicular to the main tee to make a grid of 600x 1200mm. Finally 600 mm cross tees are interlocked in the pre cut slots in the 1200mm tees at 1200 mm center to center in direction parallel to the main tee. Cross Tees having length more than 600 mm are to be supported independently. 4.5 mm thick E board with square edge of size 595x595 mm shall be placed into the grid size of 600x600mm. Size of grid as specifed by manufactures, complete all as specified and directed.

M & L for 75 mm thick PCC 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) as in sub base finished even and rough, complete all as specified and directed.

S & F anodized aluminium frame powder coated (minimum thickness of powder coating 50 micron) for doors, windows ventilators and partitions with one or more rebated including joining cleat for fixing etc complete all as specified and directed.

Anodised aluminium door shutters powder coated (minimum thickness of powder coating 50 micron), aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc, complete all as specified and directed.

S & F 5.5 mm thick sheet glass ordinary quality and glazing with snap beading in square and fixed to aluminium sections, complete all as specified and directed.

Schedule 'A' Part-II (Internal Electrification)

Taking down carefully unserviceable aluminium point wiring (light, fan, socket bell or power) complete, (fittings such as switches, ceiling rose lamp holder, regulators, sockets, pendants) stacking at site and keeping in safe custody for taking credit, complete all as specified and directed.

Taking down ceiling fan any sweep, removing blades, cleaning the fan completly for dust and dirt and hanging the same back to its original position including connecting the 3 core flexible copper wire to ceiing rose etc after the completion the point wiring including replacement old unservicable fan hook, rubber pad, nut bolts and washers etc, complete all as specified and directed by Engineer in charge.

M&L Point wiring with PVC insulated unsheathed 1100 volt grade FRLS cable with multi stranded copper conductor of size 1.5 Sq mm (Nominal area) drawn through and including non metallic rigid PVC conduit medium grade ISI marked not less than 20mm dia ,concealed in wall and surface on ceiling with all conduit fittings & fixing acessories inculding sunken anodised pressed steel terminal box not less than 1.2mm thick covered with 3 mm thick plastic laminated sheet cover of suitable size with brass screws for mounting switches, sockets, regulators with and including 1.5sqmm FRLS multi stranded copper conductor drawing as continuous earth wire connected to main earth and earth dolly complete all as specified for the following:-

One light point controlled by one switch 5 Amp.

One ceiling fan/exhaust fan point controlled by one switch 5Amp

One socket out let 5Amp controlled by one switch on same board.

One socket out let 5 Amp controlled by one switch on independent board.

All as per ser item No 2.03 here in before but point wiring with 2.5 sqmm FRLS multi stranded copper conductor cable for main circuit and 2.5 sqmm cable as earth continuity conductor for one 15 Amp socket out let controlled by one 15 Amp switch on independat board, complete all as specified and directed

S&F Switch piano flush type 5 Amps single pole one way, complete all as specified and directed.

S&F Switch socket combination 2 in 1, 3 pin 5 Amps flush type, complete all as specified and directed.

S&F Switch socket combination 2 in 1 5 pin 5 /15 Amps flush type, complete all as specified and directed.

S&F Ceiling rose 3 terminal complete PVC/polycarbonate isolated body, complete all as specified and directed.

S & F Stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc as required, complete all as specified and directed

S & F Integrel sleek extruded batten aluminium /CRCA channel fitting with LED 18 watt complete with all accessories and including connecting up with three core twisted flexible copper conductor cable with suitable size of 230V, 50 Hz, Cat part No. BLRB DB 118 ( for batten fitting) & Cat part no. BLRB18W CW LED (for LED 18 watt ) of Bajaj or equivalent in approved make, complete all as specified and directed.

S&F LED light fitting 1x9W bulk head luminaries IP 65 complete with all accessories including LED lamp 9 watt , connecting up with twin core twisted flexible copper conductor cable with suitable size of 230V 50 Hz, complete all as specified and directed.

S&F Lamp holder PVC/polycarbonate type with back plate suitable for batten fittings, complete all as specified and directed.

S& F LED bulb 7 watt , complete all as specified and directed.

Sheet metal enclosure distribution board SPN 12 way 230 V, 50 Hz double door with neutral, Earthing bar and din rail, complete all as specified and directed.

S & F MCB DP 63 Amps 10 KA 230 volts "C" series, complete all as specified and directed.

S & F MCB single pole 6 to 30 Amps, 10KA, 230 volts 'C' series, complete all as specified and directed.

Supply and laying or fixing 1100 volts grade cable PVC insulated aluminium conductor un-armoured of 16 Sqmm 2 core flat or circular, served with inner sheathing of pace tape and overall PVC sheathed in service connection suspended by insulated hangers not more than one meter apart including 4 mm dia suspension GI wire including taking down of existing cable , complete all as specified and as directed by Engr-in-Charge.

M&L for earthing complete for bldg with galvanized mild steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 meters below ground level) with top edge of earth plate not less than 1.5 meters below ground level connected to galvanized earth wire 4.00 mm dia by means of nuts, bolts, thimbles, chuck nuts, washers of GI or steel, PCC (concrete chamber of size 300 mm x 300 mm x 300 mm inside dimension) shall be PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish , internal surface of concrete chamber shall be given 15mm thick plaster in CM 1:4, funnel with wire mesh of 22 gauge, 80 mm thick PCC pit cover 320 mm x 320 mm of RCC 1:2:4 type B-1 using 20 mm graded stone aggregate reinforced with XPM, JALLI pit shall be filled with charcoal dust and common salt all as shown in electrical plate No 3 of MES SSR Part-I (2009) as specified including provision of 15mm dia medium grade GI pipe for earth wire protection and 20 mm dia for watering complete , all excavation and earth work & connecting the earthing to an earthing test point / main switch board as specified and testing on completion, complete all as specified and directed.

Deduction to be made from BOQ for schedule of credit (Sch 'A' Part - III) Amount of Rs. 100698.50 during AOC Note:- Tenderers shall not quote for this Schedule

RAJINDRA ENGINEERS & CONTRACTORS

Kalsi Engineers and contractors

Hare krishna engineering const.

U K Engineering Works

BHARTI CONSTRUCTIONS

ASHISH CONSTRUCTION COMPANY

M/S STAR CONSTRUCTIONS