IMPROVEMENT TO AIRMEN INSTITUTE IN DC III AREA AND REPAIR AND MAINTENANCE OF FANS INCLUDING MISC INTERNAL ELECTRIFICATION WKS IN MD ACCN AT AF STN UNDER GE AVADI

Amount

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof coverings etc complete all as specified and directed

S&F Prepainted galvalume aluminium zinc coating GI based corrugated steel sheet of 0.50mm thick of any colour having tensile strength of 550 MPa as in roof covering/ cladding to wall fixed with self tapping screws all as specified and directed.

All as per item No.2 above but refixing only. (corrugated galvalume sheet obtained from item No.1shall be reused) including filling of holes with chemical adhesive of Tar plast of STP/ equivalent chemical all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed

S&F PVC (SWR) pipes 110mm dia single socketed in any length with rubber ring joints fixed to walls as rainwater pipes completed all as specifed and directed

Dismantling of wall and ceiling boards or insulation board/slabs/ blankets any thickness including snap grids of any description complete all as specified and directed

S&F Anodised aluminium snap grid frame work for false ceiling size of grid shall be 605 x 605mm comprise of perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall /intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre and including hanging rods of 6 mm dia GI ( up to 1200mm length) adjesting leval fixed to roof by means of celling cleat made out of G I flat 40x3 mm size 60 mm long and expension hold fasteners 12.5 mm dia 40 mm long complete all as specified and as directed.

S&F 10 mm thick PVC insulation panels with EPS stuck to 1mm plain PVC sheet suitably laced in false ceiling grid made of Aluminium/G.I./M.S. including necessary fastners for fixing of aluminium grid framework etc all as specified and directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises etc complete all as specified and directed

M&L for Glazed ceramic tiles in vertical surfaces of size 350x250x7mm / 450x350x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles shades and colour and including 10mm thick rendering in CM 1:4 etc all as specified and directed

M&L for Non skid ceramic coloured tiles 7-8mm thick area of each tile exc 0.06 Sqm but n.exc 0.11Sqm in floor set and jointed in neat cement slurry and pointed in coloured cement to match the tiles colour and shades and including 15mm thick screed bed in CM 1:4 complete all as specified and directed

M&L for Dismantling Stone slabs and tiles of any description or thickness in floors, aprons laid, bedded and pointed in any mortar etc. complete all as specifed and directed

M&L for Machine cut Kota stone slab flooring 20-25 mm thick laid over 20 mm thick screed bed in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc complete all as specified and directed

Taking down cement or cement-lime mortar plastering on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water of any description etc complete all as specified and directed

Rendering 10mm thick in CM 1:6 on wall/vertical surface of brick /concrete surfaces including surfaces finished even and smooth without using extra cement all as specified and directed

M&L for 5 mm thick cement plaster in CM 1:4 with WPC over 10 mm thick dubbing coat in CM 1:6 finished even and fair on wall surfaces of brick/ concrete works all as specified and directed. Note: WPC shall be measured and paid separately

M&L for preparing wall surfaces by complete removal of existing treatment and applying two coats of oil emulsion distemper over a coat of alkali resistant primer including wall care putty all as specified and as directed.

Material & Labour for preparation of newly plastered or old surface of wall and applying two coats of 100% Premium acrylic emulsion paint havingVOC less than 50 gm/litre and UV resistance asper IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade(Company Depot Tinted) with silicon additives@ 1.43 litre/ 10 sqm over and including primingcoat of exterior primer applied @ 0.90 litre/ 10sqm over old surfaces.

Taking down chowkats or frames exc 1.5 sq. m but n exc 4 sq. m with shutters (without taking off shutters from the frame) etc complete all as specified and directed

S&F aluminium frame for doors, windows, ventilators, partition with one or more rebates including joining cleat for fixing etc. complete all as specified and directed

S&F aluminium door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading, screws etc. complete all as specified and directed

S&F Brass Mortice Lock vertical type size 100mm four Lever for complete all as specified and as directed

S&F Aluminum (Die cast) body door closer hydraulically regulated designation No 3, universal type suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 Kg and fixed etc all as specified and directed

S&F 150mm long floor door stopper Aluminium alloy body and tongue,anodised,with hard drawn steel spring fixed in floor complete all as specified and directed

S&F 5.50 mm thick sheet glass ordinary quality and glazing with rubber gasget of square or recatangular in shape of exc 0.5 sqm each pane for doors and partition etc complete all as specified and directed

S&F 9 mm thick prelaminated particle board of exterior grade prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with glazing clip and rubber gasket for doors and partition etc complete all as specified and directed

S&F in repair Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete all as specified and directed

S&F solid PVC door frame of size 50mmx47mm made out of 5mm thick plain colour PVC sheet reinforced with 19mm thick MS square tube of 19 gauge mitre cut at two corners and joined by inserting two Nos of 150mm long brackets of 15mmx15mm MS square tube inside the 19mm MS square tube and suitably screwed complete all as specified and as directed.

S&F factory made solid PVC moulded door shutter with wood free EPS 28 to 30mm thick (styles) with 2,4 or 6 raised panel design with 2mm thick moulded PVC sheet on front face and 2mm plain colour PVC sheet on backface, supplying and fixing in frame at site as per specification complete all as specified and as directed.

S&F 100 mm size type C21 Butt hinges extruded aluminium alloy with galvanised mild steel hinge pin anodised complete all as specified and directed.

S&F aluminium handle 150 mm cast type anodized complete all as specified and directed

S & F aluminium anodized tower bolt 100mm size complete all as specified and directed.

S&F in repairs 250mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed with screws complete all as specified and directed

M&L for preparation of old painted surfaces of wood and wooden based surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed

M&L for preparation of old painted surfaces of steel and iron of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed NOTE:- The rate shall include the cost of scaffolding and necessary safety arrangements for painting of windows and other steel items ht varies from 2mtr to 12mtr

S&F in repair tubular towel rail alumunium anodised , 20mm dia, D type 60 cm long between flanges complete all as specified and directed

S&F in repairs Vitreous China urinals, half stall type with PVC waste/ flush pipes, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, grating and Union for discharge pipe etc complete all as specified and directed

S&F in repairs Vitreous China wash Basin (flat back or angle back type) , of size 550x400mm including brackets, PTMT waste coupling 32mm, and PVC 32mm dia waste pipe including cutting for and pinning in ends of brackets or erecting stand etc, complete all as specified and directed

S&F in repairs Vitreous china water closet pan (pedestal pattern), white including fixing bolts, plastic water closet seat, black/white closed pattern with flat bottom and cover and mild steel chromium plated hinging device including 10ltrs capacity PVC flushing cistern (low levl with inlet, ball valve float), brackets, flush pipe of polyethylene of low density PVC 32mm dia for low level cistern complete all as specified and as directed.

S&F in repairs 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement, all as specified and directed.

S&F in repairs 15 mm dia Bib taps, chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for PVC/ iron pipe or for brass ferrule and fixed complete all as specified and directed

S&F in repairs 15mm dia stop valve/Angle valve, chromium plated fancy type cast copper alloy, screwed down high pressure, with crutch or butter fly handle, screwed both ends for PVC/iron pipes or for unions and fixed of,complete all as specified and directed.

S&F 15mm in repairs dia Pillar taps cast copper alloy, with capstan heads,chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts,screwed for iron pipe, complete all as specified

S&F in repairs PVC connections 15mm size with PTMT nuts of length 600 mm complete all as specified and directed

M&L for Taking up or down steel tubing and connections, including removal to store etc all as directed for 15mm bore complete all as specified and directed

All as per Item No. 46 above but for 20mm bore

S&F Unplasticised PVC pipes and fittings of 15mm dia of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc. complete all as specified and directed

All as per Item No. 48 above 20mm bore

M&L for Cutting chases or making holes in brick walls for concealed water tubing, making good to facings where required, cutting not exc 10 cm girth all as directed

S&F in repairs Stainless steel plate rack of size 900X800X230mm with screws and necessary fittings incl cutting to hole fixed to wall complete all as specified and directed.

S&F in repairs Rotational moulded polyethylene water storage tank of 500 ltr capacity ( cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed.

S&F in repairs ball valves (PVC), high pressure with polyethylene float and fly nut complete screwed for iron pipe 25mm bore complete all as specified and directed.

S&F in repairs stainless steel sinks with drainage board made of 1mm thick kitchen with plugs washer, waste pipes, cast iron cantilever brackets, connecting union to pipe over all size 915mm x 460mm bowl size 410 x 330 x 160mm, including bedding in cement mortar to dwarf wall including fixing cantilever brackets and connecting unions to pipe complete all as specified and as directed.

S&F in repair for Harrison Curtain rails, mild steel, chromium plated of thickness 40-6 microns, outer dia 19/20mm inner dia 16mm with fixing brackets, stops, rollers etc.in repair all as specified and as directed.

S&F in repairs of 4mm thick sheet glass squares or rectangular in shape of each pan not exc 0.5 sqm securing with wooden beadings/ glazing clips with oil putty etc complete all as specified and directed.

S&F inrepairs Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed

Complete Removal of existing water proofing treatment over roof including PCC of any thickness description in any position including cleaning wire brushing, watering remove of debris up to 1500 mtr distance etc., complete all as specified and as directed.

Material and Labour PCC 1:2:4 type B-0 (using 12.50 mm stone aggregate) as in, levelling course using integral water proofing compound as per manufacturers instructions including demolition of unserviceable unreinforced cement concrete as in roofs complete all as specified and directed. Note:- WPC shall be measured & paid separately.

M&L for Rendering in cment mortar 10mm thick in of 1:3 ratio on concrete surfaces of roof finished even and smooth without using extra cement to recive water proofing membarane mixed with integral water proofing compound as per manufactures all as specified and directed. Note:- WPC shall be measured & paid separately.

Supply only integral water proofing liquid complete all as specified and directed. (@200ml per bag of cement)

M&L for prepartion of the plastered surfaces by thoroughly removing all loose particles, dirt/ dust particles and applying a uniform coat of hot blown bitumen of grade VG-10 @ 1.20 kg/Sqm confirming to IS 702 over a coat of water based bituminous primer @ 0.40 ltr/ sqm and laying APP based polymeric membrane as per IS 16540-2017/ IS 16532-2017 with overlap of 100mm minimum weighing 3.6 kg/ sqm and minimum 3mm thick reinforced with polyester non woven fabric (weight not less than 150gms/ sqm) by forced application and finally finsihed the memberance surface by applying a coat of solar refelective aluminium paint @ 0.1 ltr / Sqm complete all as per manufacturer's instructions as specified and as directed.

M & L for brick work with fly ash bricks, old size bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:4 complete all as specified and directed.

Taking down carefully unserviceable point wiring copper / aluminium (light, fan, socket or power) complete, including removal of batten / conduit / gutties / wooden board etc., including fittings and fixtures such as switches, ceiling roses, regulators, sockets, light fittings, fans etc., removal from site under Sch of credit and removal of unserviceable items out of site and making good the disturbed surfaces of walls, ceilings etc., complete all as specified and as directed.

Point wiring on stone / brick masonry wall complete with two 1.5 sqmm single core PVC insulated FRLSH ,1100 volts grade unsheathed cable confirming to IS-694, 1977 with multistranded copper conductor, drawn through and including non-metalic rigid PVC conduit, conduit fittings and conduit accessories not less than 20 mm dia concealed in walls and fixed with suitable clamps on ceiling / roof trusses etc., and including provision of one 1.5 sqmm PVC insulated single core multistranded copper conductor FRLSH green in colour as earth continuity conductor and connected to common earth dolly, including steel box of required module for modular switches/sockets and regulators all as specified complete for. Note : Cost of terminal box and cutting chases for concealing pipes is deemed to be included in the item rates quoted for point wiring.

one light point controlled by one switch.

One ceiling fan point controlled by one switch and regulator

One Exhaust fan point controlled by one switch.

One switch socket outlet 3 pin 5 Amps on same board along with other switches

One switch socket outlet 3 pin 5 Amps on independent board.

All as per item No 65 here-in-before but for point wiring with two 4.0 sqmm single core copper conductor multistranded FRLSH cable and one 4.0 sqmm PVC insulated single core multistranded cable as earth continuity conductor green in colour for one 3 pin switch socket outlet, 15 Amps, on independent board and industrial socket complete all as specified and as directed.

S&F Switch piano flush type, single pole,5 Amps, 240 volts complete all as specified and directed.

S&F Switch socket 3 pin 5 amps , multi pin , flush type ,complete all as specified and directed.

S&F Switch socket 3 pin 15 Amps, multipurpose, flush type complete all as specified and directed.

S&F ceiling rose 65 X 50 mm , three terminals ,bakelite , surface complete all as specified and directed.

S&F electronic fan regulator, flush type phenolic laminated sheet etc as required complete all as specified and directed.

Supply and Fixing of Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps complete all as specified and directed.

Power / Sub-main wiring with PVC insulated unsheathed, FRLSH ,1100 volts, grade multistranded copper conductor, two runs of single core 6 sqmm conforming to IS-694, drawn through and including suitable dia rigid PVC conduit, conduit fittings and conduit accessories alongwith one run 6 sqmm PVC insulated single core multistranded copper conductor cable (green) as earth continuity conductor concealed in walls and fixed with suitable clamps on ceiling / roof trusses etc. and connecting to common earth dolly complete all as specified and as directed.

Power / Sub-main wiring with PVC insulated unsheathed, FRLSH ,1100 volts, grade multistranded copper conductor, two runs of single core 10 sqmm conforming to IS-694, drawn through and including suitable dia rigid PVC conduit, conduit fittings and conduit accessories alongwith one run 10 sqmm PVC insulated single core multistranded copper conductor cable (green) as earth continuity conductor concealed in walls and fixed with suitable clamps on ceiling / roof trusses etc. and connecting to common earth dolly including taking down carefully the existing submain wiring complete all as specified and as directed.

S&F MCB DB SPN 8 way, double door, powder coated, 240 volts, AC, 50Hz, IP 43 protected, with provision for MCB double pole as incomer and SP MCBs as outgoing with tinned copper bus bar, neutral link, earth link and connecting up complete all as specified and as directed. Note : Incoming and Outgoing MCB measured separately relevant items.

S&F Load line MCB DB TP&N 4 way, vertical, double door, powder coated, 415 volts, AC, 50Hz, IP 54 protected, fixed on wall semi flush with provision for FP MCCB 100 Amps as incomer and SP MCBs 40 / 63 Amps as outgoing with tinned copper bus bar, neutral link, earth link and connecting up complete all as specified and as directed. Note : Incoming MCCB and Outgoing MCB measured separately relevant items.

Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 6 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and directed.

Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of SPN and current carrying capacity 40 Amps, in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

S&F MCCBs100 Amps 415V,16KA, 4 Pole complete all as specified and directed.

S&F in replacement of Surface and wall mounted LED tube light fitting, 20 W, batten type, PC housing provided for efficient heat dissipation with polycarbonate diffuser and integrated electronic driver complete with all accessories , suitable for operation on AC, single phase 220 / 230 Volts , 50 Hz supply, and including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire from ceiling rose to fitting complete all as specified and as directed.

Supply & fix Recess mounting LED backlit panel ceiling light 2X2 environmental friendly new generation aesthetically designed ultra modern recess mounting luminaire with high brightness SMD LEDs as light source, LED backlit luminaire suitable for armstrong/grid ceiling complete for low ceiling applications 34/36 Watt LED (2'X2') complete with electronic driver, suitable for operation on AC, single phase , 220/230V , 50 Hz , including provision of suitable twin core copper conductor PVC insulated , 1100 Volts grade cables not more than 5 m long and connecting up ceiling rose and fittings and testing, making good the disturbed any type of ceiling including taking down old fittings all as specified and as directed.

S&F LED building security light fitting 30W made up of pressure die cast housing with toughened glass and individual high power LEDs with secondary optics, IP66 protection and impact resistance of IK07, complete pre-wired and connecting up with suitable twin core flexble copper wire including provision of necessary GI tubing medium grade 25mm bore of pipe 1.5 bent to shape with necessary clamps made out of mild steel, nuts and bolts etc., including two coats of synthetic enamel paint over a coat of red oxide primer on exposed steel surface for fixing the fitting to Bldg etc complete all as specified and as directed.

S&F of Exhaust fan, heavy duty, 300mm sweep, 1370 RPM, with louvers, metal body conforming to IS-2312-1967, AC single phase, 240 Volts, 50 Hz and connecting including provision of two way PVC connectors, 1 sqmm flexible three core multistranded copper conductor cable from ceiling rose or connector to fan including earthing and fixing arrangements like making hole in wall and finishing to shape to match adjoining surface and writing MES No.20mm height with synthetic enamel paint black complete all as specified and as directed.

Material and labour for earth continuity conductor or main earthing lead fixed to valve on batten or recess or chases or burried in ground or drawing in conduit or any other situation for loop earthing etc as reqd 4 mm dia galvanized steel wire all as specified and directed

Earthing complete with galvanised iron earth plate electrode 600mm X 600mm X 6mm thick, with and including earthing of 4mm dia GI wire protected by 15mm dia GI pipe light grade upto a length of 7.5m. The plate shall be buried directly in ground vertically to a depth not less than 2.25 metres below ground level with top edge of the earth plate at a depth not less than 1.5 metres below ground level, connected to earth lead as described here-in-before by means of bolts, nuts, washers and checknuts made out of galvanised iron or mild steel, earthing lead protected by as described here-in-before and connected to main switch board or main control board or electric pole all as shown on electrical plate No.3 of MES Sch Part-I including necessary earth work and excavation in any type of soil, plain cement concrete 1:3:6, type C1 chamber, reinforced cement concrete cover slab with locking arrangement and handle of 10mm dia MS round bars 450mm long, 1:2:4 type B1, 50mm thick with 8mm dia TMT bars at 140mm centre to centre both ways, GI pipe of bore 20mm medium grade for watering with funnel, wiremesh, salt, charcoal, lugs including testing complete all as specified and as directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m depth and getting out any type of soil for laying cables / pipes / erection of poles etc all as specified and as directed.

Removing excavated material (soil) not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point all as specified and as directed.

Returning filling in soil including spreading leveling watering well ramming in layers not exceeding 25 cm each all as specified and as directed.

Laying in trenches fine sieved excavated dry soil including spreading/leveling,cushioning for underground cables all as specified and as directed.

Supply and laying of common burnt clay building bricks,sub class B size for cable protection all as specified and as directed.

Material and labour for XLPE insulated, armoured, heavy duty electric cable with aluminum conductor, 1100 volts grade, 35 Sqmmx 3.5 core including taking down of old unserviceable cable complete all as specified and as directed:- (Note: Earth work and connected items will be measured and paid separately under respective items of schedule)

Material and labour for GI tubing light grade 40 mm bore for cable protection laid in trenches in road crossing or fixed to wall/Pole complete all as specified and as directed.

Taking down carefully and servicing the ceiling fans of any size/ make including greasing/ oiling/ repairs and replacing the spares such as cater pin unserviceable/rusted nut bolts, split pins rubber wheel bearing washers, bush and connected items all as specified and directed Note : Servicing, Spares and Rewinding shall be measured and paid for separately.

Taking down carefully and servicing the Exhaust fans of any size/ make including greasing/ oiling/ repairs and replacing the spares such as cater pin unserviceable/rusted nut bolts, split pins rubber wheel bearing washers, bush , and connected items all as specified and directed Exhaust fan of any size/ make after disconnecting the electric connections for necessary servicing and replacing the spares, rewinding etc., all as specified and directed. Note : Servicing, Spares and Rewinding shall be measured and paid for separately.

Material and Labour for painting of ceiling fans of any sweep to obtain even, smooth & glossy finish, with synthetic enamel paint of approved colour by using paint spraying devices after filling cavities with filler after cleaning all dust etc., over fan surfaces complete including writing SM/MES No. in synthetic enamel paint (Black colour) over the same surface where the existing No. was written etc., complete all as specified and directed.

Material and Labour for painting of Exhaust fan of any sweep to obtain even, smooth & glossy finish, with synthetic enamel paint of approved colour by using paint spraying devices after filling cavities with filler after cleaning all dust etc., over fan surfaces complete including writing SM/MES No. in synthetic enamel paint (colour as approved) over the same surface where the existing No. was written etc., complete all as specified and directed.

Material and Labour for rewinding of fan motor with super enameled copper winding wire of same gauge and weight after cutting and removing the existing burnt/heated up windings, including cleaning of rotor, stator and varnishing, heating and providing fresh insulating materials for Ceiling fan of 1200/1400 mm sweep including dismantling and reassembling of fan motor complete all as specified and directed.

All as per Item No.97 herein before but for Exhaust fan 200 to 300 mm sweep all as specified and directed

All as per Item No.97 herein before but for Exhaust fan 350 to 450 mm sweep all as specified and directed

Supply only ball bearing suitable for ceiling fan of size 1200/1400mm sweep all as specified and directed

Supply only ball bearing suitable for exhaust fan of any size and make complete all as specified and directed.

Replacement of old/unserviceable capacitor of capacity 2.5 µfd for the fans in position complete all as specified and directed.

Replacement of old/unserviceable capacitor of capacity 4 µfd for the fans in position complete all as specified and directed.

Supply and fix in replacement of ventilation fan(plastic body) motors suitable for 200/250mm sweep complete all as specified and directed.

Supply and fix PVC canopy/Ceiling fan cap with fixing screws etc suitable for ceiling fan 1200/1400mm sweep etc., complete all as specified and as directed

Supply and fix ceiling fan blade with fixing accesories etc suitable for ceiling fan 1200/1400mm sweep etc., complete all as specified and as directed

Supply and fix exhaust fan blade (metal body) with fixing accessories etc suitable for exhaust fan 300mm sweep etc., complete all as specified and as directed

Supply and fix exhaust fan louver (shutter) metal body with fixing accessories etc suitable for exhaust fan 300mm sweep etc., complete all as specified and as directed

M&L for ventilation fan blade (PVC type) suitable for 200/250 mm sweep complete all as specified and directed.

S&F in replacement louvers with shutter plastic body suitable for single phase 240 Volts ventilation fan 200/250 mm sweep with necessary fixing accessories after taking down existing all as specified and directed. NOTE: Louver Shutter are to be replaced up to high rise bldgs upto 8 storey, including all necessary T&P and fixing accessories etc.

Replacing ceiling fans down rods fabricated out of 15 mm dia GI pipe medium grade duly cutting/ threading/ drilling etc. Suitable for ceiling fans (1200/1400 mm sweep) fixed by means of check nut and split pin, 'U' clamp bolts, nuts, washers, rubber split pin check nut etc., complete all as specified and as directed.

M&L for making hole for fixing of exhaust/ventilation fan size 200 mm to 380 mm with necessary civil work as per site requirement complete make good the wall/ventilation window match with exist complete all as specified and directed.

Replacing un serviceable check nut and split pin including 'U' clamp bolts, nuts, washers, rubber split pin check nut etc.,complete from ceiling fan 1200/1400 mm sweep etc., all as specified and as directed.

Supply and Fix ceiling fan hook made out of 40 x 6 mm MS flat iron and 10 dia MS round bar bend to shape for hanging ceiling fans including taking down existing unserviceable fan hook complete all as specified and as directed.

muthu constructions (BID ID -3152989)

SAMYDOSS CONSTRUCTIONS (BID ID -3155091)