GE/PKT-54/2020-21

Amount

To attend and rectify of sewage system complaint in daily routine basis as per complaint lodged by user at complaint cell of AGE B/R-I Sub division by deploying manpower by cleaning/clearing/removal blockage such as blockage/ chocked in any type/size/height/depth/location of WCs/urinal/bathroom /kitchen /WHB upto 1st manhole of sewage line along with any type/size/height/depth bore of outlet SGSW/PVC/CI/ UPVC/RCC etc pipe & including all kind of traps such as inspection chamber/Floor/ Nahani /Gully /Intercepting /bottle trap/P or S/multi floor traps of any type SGSW/PVC/CI/UPVC etc and in any position below or above ground level, in any floor, located in different situations, including opening/clearing eyes of sewage waste pipes/vent pipe etc, opening the access cover/grating and taking out/removing all material such as sludge/ soil waste/sludge water/polythene /mud/silt/liquid/semi liquid / semi solid/solid /bricks bats/debris/soil etc any unwanted materials of any kind etc including flushing with adequate water after cleaning make the all system fully functional to the entire satisfaction of Engr-in-Charge, re-fixing the existing opened access cover and removing all retrieved material/unwanted/foreign material in any liquid/solid state etc outside the periphery of defence land at his own arrangement where sanitary hazards do not take place as per directions/ instructions of civil authority and buried in excavated pits in suitable size and depth and covering the same with minimum 25cm thick compacted layer of soil with the soil obtained from excavation of pit including all excavations and earth work including applying bleaching powder to maintain hygiene. Adequate water for flush out be arranged by the contractor without any extra cost complete all as specified and directed

To attend and rectify of sewage system complaint in daily routine basis as per complaint lodged by user at complaint cell of AGE B/R-I Sub division by deploying manpower by opening of man hole cover and Cleaning of RCC/UPVC/PVC/SGSW/CI sewage pipe line of size 100mm/150mm/160mm/200mm/300mm bore laid in trenches in any depth from gully trap /inspection chamber to man holes or from manholes to manholes or manhole to septic tanks in horizontal or vertical position including connected manhole in any size/depth by rodding from gully trap /inspection chamber to man holes or from manholes to manholes or manhole to septic tanks, bailing out waste water from Manholes & sewage pipe line, taking out/removing all material such as sludge/ soil waste/polythene /mud/silt/liquid/semi liquid / semi solid/solid /bricks bats/debris/soil/night soil waste including any unwanted materials of any kind etc from sewage line including connected manholes including flushing with adequate water after cleaning of same and make the sewage pipe line along with manholes fully functional to the entire satisfaction of Engr-in-Charge, re-fixing the existing opened access cover and removing all retrieved material/unwanted/foreign material in any liquid/solid state etc outside the periphery of defence land at his own arrangement where sanitary hazards do not take place as per directions/ instructions of civil authority and buried in excavated pits in suitable size and depth and covering the same with minimum 25cm thick compacted layer of soil with the soil obtained from excavation of pit including all excavations and earth work including applying bleaching powder to maintain hygiene. Adequate water for flush out be arranged by the contractor without any extra cost complete all as specified and directed

To attend and rectify of sewage system complaint in daily routine basis as per complaint lodged by user at complaint cell of AGE B/R-I Sub division by deploying manpower by opening of man hole cover by cleaning/clearing/removal blockage of manholes at different locations in any size and depth not exceeding 4.50 meter from GL, mouth of outlet/inlet pipes by taking out/removing all material such as sludge/ soil waste/polythene /mud/silt/liquid/semi liquid / semi solid/solid /bricks bats/debris/soil/night soil waste including any unwanted materials of any kind etc causing blocking, including bailing out waste water from manholes, cleaning the sides and floors of the manhole including flushing with adequate water after cleaning make the manholes fully functional to the entire satisfaction of Engr-in-Charge re-fixing the existing opened access cover and removing all retrieved material/unwanted/foreign material in any liquid/solid state etc outside the periphery of defence land at his own arrangement where sanitary hazards do not take place as per directions/ instructions of civil authority and buried in excavated pits in suitable size and depth and covering the same with minimum 25cm thick compacted layer of soil with the soil obtained from excavation of pit including all excavations and earth work including applying bleaching powder to maintain hygiene. Adequate water for flush out be arranged by the contractor without any extra cost complete all as specified and directed.

Notes :-For serial item no 01,02,03 (i) contractor will deploy two mazdoor daily to attend day to day complaint as mentioned above in the concerned items. Mazdoor will report daily at compliant cell of AGE B/R - I Sub division at 8.30 AM to collect complaints and depart 5pm after attending all complaints. In case of none attending complaints in same day, recovery @ RS 250 per complaints will be recovered from contractor and in case of Non deployment of Mazdoor recovery @ RS 500/day per mazdoor will be recovered from contractor. (ii) Contractor accredited representative shall be available during cleaning. (iii) Unit rate quoted by tenderer shall included for all precautions to be taken by workers while working in foul condition, Contractor shall take all necessary actions. (iv) Unit rate quoted by tenderer shall include excavation of borrow pits for dumping, removing including loading/ unloading and transportation in covered container etc (v) Unit rate quoted by tenderer shall included for Washing, cleaning floors with adequate water of any type of drops and splashes and leaving premise clean and tidy. (vi) Unit rate quoted by tenderer shall included for use of all scaffolding, trestles, ladders, cradles etc, hoisting, lowering and protective measures etc up to four storeys height of bldgs.

Cleaning of septic tank at different locations of any description up to any users capacity Mechanically only with using sewage tankers/ Truck mounted hydraulic jet pressure machine with heavy duty flushing the sewage line and with heavy duty sewage pumps sewage suction pump including necessary other arrangements such as sweepers to clean up the site after work in the following steps:- (i) Bailing out/dewatering of septic tank (ii) Removing of all sludge/waste material (liquid/ semi liquid /solid/semi solid), Silt, bricks bats, debris, mud, soil, polythene etc any kind of materials from all chambers of the septic tank, clean the floor and walls of the tank after removing the same complete (iii) Removing the blockage of inlet/outlet pipe in any depth ,in any situation (iv) Finally flushing septic tank including inlet/outlet with adequate water and making fully functional the septic tanks with entire satisfaction of Engr-in-charge and taking out all type material, sludge/ soil waste, liquid/ semi liquid /solid/semi solid or any unwanted materials of any kind etc and removing outside the periphery of defence land at his own arrangement in packed container where sanitary hazards do not take place as per directions/ instructions of civil authority and buried in excavated pits in suitable size and depth and covering the same with the soil obtained from excavation of pit including all excavations and earth work including applying bleaching powder to maintain hygiene. Adequate water for flush out sludge to be arranged by the contractor without any extra cost and including taking out manholes cover and re-fixing the same after cleaning/removing blockage, fully functional complete all as specified and directed. Note: - A particular septic tank which is undertaken once for cleaning and paid for shall be kept functional for entire contract period and no extra payment shall be made for repetitive cleaning if required

M & L for Dewatering/pumping/Bailing out of soak well/filter bed at different locations completely of size not exc 1.80 mtr dia and not exc 4.50 mtr depth Mechanically only with using sewage tankers/ Truck mounted hydraulic jet pressure machine with heavy duty flushing the sewage line and with heavy duty sewage pumps sewage suction pump including necessary other arrangements such as sweepers to clean up the site after work including taking out/removing all material such as sludge/ soil waste/polythene /mud/silt/liquid/semi liquid /night soil waste etc by only sewage suction pipe including flushing with adequate water to make the same sewage system fully functional to the entire satisfaction of Engr-in-Charge, re-fixing the existing opened access cover and removing all retrieved material/unwanted/foreign material in any liquid/solid state etc outside the periphery of defence land at his own arrangement where sanitary hazards do not take place as per directions/ instructions of civil authority and buried in excavated pits in suitable size and depth and covering the same with minimum 25cm thick compacted layer of soil with the soil obtained from excavation of pit including all excavations and earth work including applying bleaching powder to maintain hygiene. Adequate water for flush out be arranged by the contractor without any extra cost complete all as specified and directed complete all as specified and directed. Note:- A particular soak well/filter bed which is undertaken once for cleaning and paid for shall be kept functional for entire contract period and no extra payment shall be made for repetitive cleaning if required

All as per Ser item no 05 herre-in-before but size of soak well exc not 3.00mtr dia and not exc 6.00mtr depth.

Cleaning/clearing/removal blockage of manholes any size & depth not exceeding 4.50 meter from GL, (as required) by manually or machinery using with sewage tankers/ Truck mounted hydraulic jet pressure machine with heavy duty sewage pumps flushing the sewage line and with heavy duty sewage suction pump including necessary other arrangements such as sweepers to clean up the site after work by opening of man hole cover of manholes at different locations in any size and depth including mouth of outlet/inlet pipes by taking out/removing all material such as sludge/ soil waste/polythene / mud/silt/liquid/semi liquid / semi solid/solid /bricks bats/debris/night soil waste, vegetation, deposited mud or any other unwanted materials of any kind etc causing blocking including bailing/dewatering/pumping out all type liquid materials from manholes ,cleaning the sides and floors of the manhole, including flushing with adequate water after cleaning make the manholes fully functional to the entire satisfaction of Engr-in-Charge, re-fixing the existing opened access cover and removing all retrieved material/unwanted/foreign material in any liquid/solid state etc outside the periphery of defence land at his own arrangement where sanitary hazards do not take place as per directions/ instructions of civil authority and buried in excavated pits in suitable size and depth and covering the same with minimum 25cm thick compacted layer of soil with the soil obtained from excavation of pit including all excavations and earth work including applying bleaching powder to maintain hygiene. Adequate water for flush out be arranged by the contractor without any extra cost complete all as specified and directed. Note:- A particular manholes which is undertaken once for cleaning and paid for shall be kept functional for entire contract period and no extra payment shall be made for repetitive cleaning if required

Surface excavation not exc 30 cm depth and averaging 15cm deep in foul condition for removing heaps of waste, cleaning of flora, fauna , foliage and bushes around septic tanks, manholes and soak pits removing debris/ heaps of bushes etc from vicinity and depositing at a place where directed complete all as specified and as directed

Taking out old brick bats from soakage pit/wells and removing the same outside the periphery of defence land at his own arrangements where sanitary hazards do not take place as per directions/ instructions of civil authority. Note:- Unit rate quoted by tenderer shall include taking out brick bats and removing including loading / unloading and transportation etc.

Cleaning/clearing/removal blockage (as required) by manually or machinery using sewage tankers/ Truck mounted hydraulic jet pressure machine with heavy duty sewage suction pumps flushing the sewage line and including necessary other arrangements such as sweepers to clean up the site after work by opening of man hole cover of connected man holes at different locations and Cleaning/removing blockage of RCC/UPVC/PVC/SGSW/CI sewage/waste pipe line of size 100mm/150mm/160mm/200mm/300mm bore, at different locations, laid in trenches in any depth from gully trap /inspection chamber to man holes or from manholes to manholes or manhole to septic tanks in horizontal or vertical position including connected manhole in any size/depth from gully trap /inspection chamber to man holes or from manholes to manholes or manhole to septic tanks, bailing out waste water from Manholes & sewage pipe line, taking out/removing all material such as sludge/ soil waste/polythene /mud/silt/liquid/semi liquid / semi solid/solid /bricks bats/debris/soil/night soil waste, vegetation including all other any unwanted materials of any kind etc casing blockage from sewage line along with manholes including flushing with adequate water after cleaning of wall/floor surface of manholes and make the sewage pipe line along with manholes fully functional to the entire satisfaction of Engr-in-Charge, re-fixing the existing opened access cover and removing all retrieved material/unwanted/foreign material in any liquid/solid state etc outside the periphery of defence land at his own arrangement where sanitary hazards do not take place as per directions/ instructions of civil authority and buried in excavated pits in suitable size and depth and covering the same with minimum 25cm thick compacted layer of soil with the soil obtained from excavation of pit including all excavations and earth work including applying bleaching powder to maintain hygiene. Adequate water for flush out be arranged by the contractor without any extra cost complete all as specified and directed.

Note:- A particular sewage pipe line including manholes which is undertaken once for cleaning and paid for shall be kept functional for entire contract period and no extra payment shall be made for repetitive cleaning if required

Material and Labour loose filling with aggregate of broken bricks , gauge 80mm to 150 mm in soakage pit/ soakage wells complete all as specified and directed.

Removing the building material such as broken brick dust chipping of stone/cement concrete, sand aggregate, AC sheet scrap including necessary excavation if required at site etc to a distance of exc 100M and upto 1000M from the loading place including loading, unloading and stacking at the destination spreading and leveling at the low laying area as directed. Note:- The building material (average) will be loosen by excavating and brought to the shape of stack for measurement before loading 0.65 cum of material will be measured as one load for all type of materials given above.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in any type of soil complete all as specified and directed. Note:-(1) The excavation work will be carried out by manually or mechanical means in any location/ area as directed by Engr-in- charge. (2) Any damage occur to water supply pipe line/ electric cable/existing drain/sewage line during excavation work will be make good up to satisfaction of Engr- in-charge.

All as per srl item No 13.00 here-in-before but depth exc 1.50 m and but exc 3.00 meters.

All as per srl item no. 13.00 here-in-before but depth exc 3 m but not exc 4.5 m deep.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm with any type of soil complete all as specified and directed.

Removing excavated Soils material to a distance exc. 250m but n exc. 500 m and depositing where directed.

M&L for UPVC pipe 160mm dia type "B" with wall thickness 4mm(min) of pressure rating 8 KN/sqm laid in trenches and jointed with cement solvent including testing complete all as specified and directed including demolition and breaking up drain pipes in cement mortar including demolition of PCC bedding and haunching complete all as specified and directed

M&L for concrete bed to drain pipes including packing under,and haunching against the sides of pipes after they are laid and tested in Cement concrete 1:4:8 type D-2 using 40 mm graded crushed stone aggregate for Bore of pipe in 160mm complete all as specified and directed

Material and Labour for UPVC pipe 200mm dia type "B" with wall thickness 4mm(min) of pressure rating 8 KN/sqm laid in trenches and jointed with cement solvent including testing complete all as specified and directed including demolition and breaking up drain pipes in cement mortar including demolition of PCC bedding and hunching complete all as specified and directed

M&L for concrete bed to drain pipes including packing under,and haunching against the sides of pipes after they are laid and tested in Cement concrete 1:4:8 type D-2 using 40 mm graded crushed stone aggregate for Bore of pipe in 200mm complete all as specified and directed

Dismantling of cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required Internal dia of pipe in 150mm complete all as specified and as directed.

M & L for reinforced cement concrete pipes 200mm bore, class NP3, laid and jointed complete with collars, complete all as specified and as directed.

M & L for Cutting into existing manholes for connection new drains making good to pipes and rendering, cutting out existing benching for and forming branch channel in cement mortar 1:2:4 type B-1, smooth finished and reforming benching as required for 150 mm dia pipe complete all as specified and as directed.

All as per ser item No 24.00 here-in-before but 200 mm dia pipe complete all as specified and as directed.

Dismantling of cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required Internal dia of pipe in 75mm/100mm complete all as specified and directed

S&F of spun Cast iron soil, waste and vent pipes ISI marked, in any length with or without ears with cement joints, laid in trenches or in floors bore of pipe100mm complete all as specified and directed

S&F of spun Cast iron soil, waste and vent pipes ISI marked, in any length with or without ears with cement joints, laid in trenches or in floors bore of pipe 75mm complete all as specified and directed

S&F of spun Cast iron soil, waste and vent pipes ISI marked, in any length with or without ears with cement joints, fixed to walls bore of pipe 75mm complete all as specified and directed

All as per item 29.00 here-in-before but except pipe. Note: - Old spun Cast iron soil, waste and vent pipes any type retrieved from dismantling shall be used)

S&F of spun Cast iron soil, waste and vent pipes ISI marked, in any length with or without ears with cement joints, fixed to walls bore of pipe 100mm complete all as specified and directed

All as per item 31.00 here-in-before but except pipe. Note: - Old spun Cast iron soil, waste and vent pipes any type retrieved from dismantling shall be used)

M & L for Cast iron bends (ISI marked) (any radius) diminishing pieces or tapers (larger bore measured), bore of pipe 100mm, complete all as specified and directed

M & L for Cast iron bends (ISI marked) (any radius) diminishing pieces or tapers (larger bore measured), bore of pipe 75mm complete all as specified and directed

M & L for Cast iron branch pieces (ISI marked) , double (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches, bore of pipe 75mm, complete all as specified and directed

M & L for Cast iron branch pieces (ISI marked) , double (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches, bore of pipe 100mm, complete all as specified and directed

S&F of Stack clamps made out of 50mm by 5mm flat iron and 16mm dia round iron stays. Including bolts and nuts and securing ends of stays to wall or roof suitable for 100mm bore pipe complete all as specified and directed

S&F of Stack clamps made out of 50mm by 5mm flat iron and 16mm dia round iron stays. Including bolts and nuts and securing ends of stays to wall or roof suitable for 75mm bore pipe complete all as specified and directed

Demolition and breaking up drain pipes (Salt glazed ware, PVC/AC or Reinforced concrete) set in cement mortar, and taking out of trenches, if required, Internal dia of pipe in 75mm/100mm complete all as specified and as directed.

S&F of PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and as directed.

S&F of PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and as directed.

Taking down eaves gutter and rain water pipe any size any pattern , PVC/ AC pipe including all fittings ,heads shoes, bends etc including removal to store ,Internal dia of pipe in 75mm/110mm complete all as specified and directed.

S&F of PVC (SWR) pipes 75mm bore single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed.

S&F of PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed.

S&F of PVC (SWR) bends any radius 75mm dia complete all as specified and as directed.

S&F of PVC (SWR) bends any radius 110mm dia complete all as specified and as directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for, complete all as specified and as directed.

Material and Labour for Plain Cement concrete 1:3:6 Type C-1using 20mm graded crushed stone aggregate as in filling of sunken floor to receive floor toping complete all as specified and directed.

Material and Labour for 25mm thick Cement concrete in sub base for receiving floor tiles and mass concrete using type B1,1:2:4 (20 mm graded crushed stone aggregate) complete all as specified and directed.

Material and Labour for 15mm thick plaster in cement sand mortar (1:4) mixed with water proofing compound (conform to IS 2645-Specifictions for integral cement water proofing compound) as approved as per manufacturer’s instructions shall be applied both on floor and wall as in sunken portion complete all as specified and directed.

Cleaning of all foreign material such as fungus, mass, dust ,debris etc by brushing and dusting, washing down with water, sprinkle water on the surface and ensure water does not stand any where (b) Apply a coat of Moisture Cured High Tensile Elastomeric Modified Poly Urethane Based Liquid Membrane on floor as well as on wall as per manufacturer’s instructions complete all as specified and directed.

M & L for 50 mm bore ‘medium grade’ galvanized pipe as in spout including necessary cutting to wall/beam etc and proper setting in cement mortar 1:3 , complete all as specified.

S&F of joint free non skid Ceramic tiles, coloured, superior quality 7 to 8mm thick (square/ rectangular) polished, area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:6 complete all as specified and directed. Note:-The texture ,colour ,Shade of tiles & laying of tiles to any pattern & any design with one or more colours shall be approved by GE and Rates also including in this item for necessary raking circular cutting or notching and waste on tiles.

S&F in repair for 15mm dia 600 mm long PVC connection including brass check nut at both ends screwed both end for iron pipes complete all as specified and as directed.

S&F in repair 100 mm dia steel grating with hole/without hole for whb waste pipe fixed in position complete all as specified and directed.

S&F in repairs 15mm bore chromium plated Stainless Steel jet spray Universal complete set with flexible pipe not less than 90 cm long suitable for EWC fixed to pipe complete all as specified and directed Make :Hindware 511678 Stainless Steel Jet Spray Universal (Chrome, 2 Pieces) or equivalent in any of the make mentioned in list of products.

S&F in repairs 15mm bore choromium plated (Health faucet) with 8mm Dia, 1.2 Meter long flexible tube and wall hook with N.R.V (Back Flow Preventer) Make : Jaquar Health Faucet ALD 577 or equivalent in any of the make mentioned in list of products.

S&F in repairs Vitreous China Urinal white, vitreous, china, half stall type, flat back large of size 580mmx380mm x 350mm or 450mmx350mmx300mm with CP urinal spreader ,CP brass coupling to connect urinal pan with waste pipe and chromium plated adopter to connect pan with flush pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement flush pipe, grating and Union for discharge pipe complete all as specified and directed.

S&F in repairs Vitreous China urinals, urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating, CP urinal spreader and union for discharge pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; including automatic flushing cistern with brackets,flush pipe, grating and Union for discharge pipe complete all as specified and directed.

Supply and fixing in repair Vitreous China wash down water closet pan including P or S trap (pedestal pattern), white or in matching colour of tiles (excluding flushing cistern and flush pipe) including plastic water closet seat, white or in matching colour , closed pattern with flat bottom, and cover and mild steel chromium plated or aluminized hinging device and wash down water closet complete all as specified and as directed.

Supply and fixing in repair Vitreous China squatting pan, `Orrisa' pattern, size 580 x440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor complete all as specified and as directed.

S&F in repairs Single Piece-WC with UF soft close seat cover, Hinges, Fixing Accessories, Accessories Set and Cistern fittings,Size:360mmx725mmx735 mm, S Trap-300 mm in any coloure complete all as specified and directed Make :Jaquar SOLO SLS-WHT-6851S300UF or equvalent in any of the make mentioned in list of products.

S&F in repairs PVC Cistern Fittings with complete fixing Accessories & Set for single Piece-WC with combined flush tank, any type, pattern & size such as for Make :Jaquar SOLO SLS-WHT-6851S300UFor equivalent in any of the make mentioned in list of products.

S&F in repairs 75mm PVC floor trap, ISI marked with grating incl jointing to waste pipe fixed with solvent cement complete all as specified and as directed.

S&F in repairs 75mm PVC(SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and as directed.

S&F in repairs Cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1, (1:2:4) for diameter of outlet 75mm complete all as specified and as directed.

S&F in repairs Plastic water closet seat, white/coloured, closed pattern with recessed bottom, & cover & mild steel CP or aluminised hinging device complete all as specified and as directed.

S & F in repair for Brass CP Urinal spreader 15mm dia pipe complete all as specified

Dismantling of fencing post or struts (wood, steel, RCC) any section , post embedded in concrete , brick work, masonry etc , including taking out embedded portion and making good distrubed ground complete all as specified

S&F of Hand rails, half round or other stock section or core for wooden hand-rail straight portion,drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc.,and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

All as per srl item no. 70.00 here-in-before but fixing only old mild steel work any type & any size. Note: Old mild steel work any type & any size retrieved from dismantling shall be used.

Dismantling of fencing wiremesh of any type or any description, complete all as specified and directed.

Fixing only chain link MS galvanised fencing mesh size 75mm x 75mm made with 3mm dia GI wire including line wires to any type of standards, rails, straining bolts, etc including provision of binding wire complete all as specified and directed.

Supply only chain link MS galvanised fencing mesh size 75mm x 75mm made with 3mm dia GI wire, any type complete all as specified and directed.

Material and labour for PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

M&L for Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips Fe-410-W 432 (Part I) (Gde.E-250) Part- I quality-A or Fe 290 (Gde -E-165) complete all as specified and directed

S&F in repair mild steel screw bolts with haxagonal or squre heads at one end and screwed at other end fitted with washers and one hexagonal nut exc 5cm but n exc 10cm long and 12 mm dia complete all as specified and directed.

S&F in repair Galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings & straining & fixing to any type of standard rails straining bolts, including, securing or tying at crossings with & provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and directed.

Fixing only in repair galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and directed.

M&L for in repair Providing and fixing concertina coil fencing with punched tape concertina coil 610mm dia with following specifications:- (i) Coil Dimension :- (a) Coil opening diameter (610mm+20mm, -0mm) before stretching. b) When stretched upto 6 meter length -coil diameter not less than (580mm+20mm-0mm) c) Coil having 50 Nos spiral turns & 129 nos clips in 06 meter length and weight not less than 9Kg + 5% excluding spike and handles (ii) Razor barb BTO-22 a) Barb thickness 0.5mm (+- 0.05mm) b) Barb width 15mm (+-1mm) c) Barb length 22mm (+-1mm) d) Barb spacing 35mm (+-1mm) e) Steel strip (punched tape/RBT)= The punched tape shall be CR3 grade cold reduced low carbon steel as per IS 513:2008 with pre painted Aluminium Zinc alloy in accordance with IS 15965:2012/AZ150/Class 3. (iii) Spring Core wire (a) Nominal dia of uncoated wire = 2.59mm (+-0.035mm) b) Galvanisation = The core wire should have thickness of hot dipped galvanised zinc to 290 g/m2 minimum as per the specification BS EN ISO 1461, Similarly, Indian Specification IS 4826. d) High tensile strength not less tann 1620 N/Sqmm iv) Heavy duty "J" clip for attachments" a) Material= SS 304 Stainless steel b) Dimension= 29mm x 8mm x 1.6mm

Material and labour for broken glass coping on top of wall in CM 1:3 including 20mm thick cement mortar rendering complete all as specified and directed.

Demolition of RCC work,Roofs, floors , beams staircases, landing, chajjas, & similar suspended work cement concrete is reinforced (reinforcement cut as required to facilitate demolition) complete all as specified and directed

M & L for precast reinforcement cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in cover slabs( for manholes etc.)chulla hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces set in cement mortar (1:6) complete all as specified and as directed. Note:- Reinforcement shall be measured and paid separately).

Material and labour for RCC type B1 (1:2:4) using 20 mm graded aggregate in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under reamed piles and mass concrete complete all as specified and as directed.

Material and labour for RCC type B1 (1:2:4) using 20 mm graded aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, blaconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

Material and labour for RCC type B1 (1:2:4) using 20 mm graded aggregate in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed.

Material and labour for RCC type B1 (1:2:4) using 20 mm graded aggregate in Columns, pillars, piers, posts and struts complete all as specified and as directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft & raft beams, sides & soffits of foundation & plinth beams; and similar work; verticle or to batter Fair finished surfaces of concrete flat complete all as specified and as directed.

Formwork to soffits and sides of suspended slabs such as roof slabs, floor slabs, landings & similar work; not exc. 200m thick (Horizontal or sloping) Fair finished surfaces of concrete flat complete all as specified and as directed.

Formwork to sides & soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors & beams, etc. Fair finished surfaces of concrete flat complete all as specified and as directed.

Formwork to sides of pillars, posts, struts, piers,columns, and stanchions Fair finished surfaces of concrete Square, rectangular or polygonal complete all as specified and as directed.

Material and labour for Mild steel TMT bars 10mm dia & over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality complete all as specified and as directed.

All as per srl item No.92.00 here-in-before but 8 to 10 mm dia as in stirrups, spacers and binders complete all as specified and as directed.

Material and labour for Providing precast RCC Jalli 35 mm thick(Measured solid), including all moulding type B-0 1:2:4 using 12.5mm graded stone aggregate set in cement mortar 1:4 complete all as specified and directed. (Note : Demolition will be measured with demolition of RCCwork)

Material and labour for Precast cement concrete type B1 (1:2:4) using 20 mm graded aggregate in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings, kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, anchorage blocks, bonders (for stone walling), corbels, brackets, etc.(of any section indicated), balusters with plain fair faces, including chamfers, weatherings, throating etc. and setting in CM(1:6) with joints to match complete all as specified and directed. (Note : Demolition will be measured with demolition of RCCwork)

Dismantling structural steel work including doors gates, grills but excluding framed truss etc complete all as specified and directed

S&F of Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks,cattle trap & similar work conforming to Fe 290-0 Gde E-165,ornamental and intricate design complete all as spd and directed.

S&F of Rolled mild steel ornamental , intricate design and decorative type steel gate framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc.,road sign board of angle or other section, complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with & including either hooks & hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rails and guides) and hanging; also fastening and fixing Fe 410 -W (Gde-E- 250) quality-A complete all as spd and directed.

S&F of Mild steel, plain, black 1.6mm thick sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws,clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred, angles, etc. as required complete all as specified and directed.

S&F in repair Mild steel, plain, black 1.6mm thick sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws,clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred, angles, etc. as required complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry built in cement mortar or cement lime mortar including all quions, arches, pillars,PCC coping ,man-holes/ septic tank/ soak well etc in sewer works complete all as specified and directed.

Material and labour for burnt brick work with sub-class 'B' bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

All as per srl item No 102.00 here-in-before but except bricks. Note: Old Serviceable bricks quantity retrieved from demolition shall be used.

Material and labour for burnt brick work with sub-class 'B' bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:4 complete all as specified and directed.

All as per srl item No 104.00 here-in-before but except bricks. Note: Old Serviceable bricks quantity retrieved from demolition shall be used.

Material and labour for brick work with subclass ‘B’ old size burnt bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:4 as in half thick brick wall complete all as specified and directed.

All as per srl item No 106.00 here-in-before but except bricks. Note: Old Serviceable bricks quantity retrieved from demolition shall be used.

Material and labour for providing cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) as in coping, bed blocks including necessary form work, weathering slightly rounded or chamfered angles and throating, complete all as specified and directed.

Material and labour for PCC in foundations, filling and mass-concrete type D-2 (1:4:8) using 40 mm graded stone aggregate complete all as specified and directed.

Material and labour for PCC 1:2:4 type B-1 using 20mm graded crushed stone aggregates as in surface channels and drains complete all as specified and as directed.

Material and labour for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc complete all as specified and directed.

Taking down cement plaster of any description and thickness on walls/ceilings etc including racking out joints, hacking for key, scrubbing down with water etc including necessary scaffolding up to four storeys height of bldgs if required and removing of debris out of MoD land complete all as specified and as directed.

Material and labour for rendering 15mm thick in CM 1:4 mixed with liquid water proofing compound (as per manufacturer’s instructions) on fair faces of brick work ,concrete surface of wall, fin, facia, chajjas, parapet and similar article finished surface even and smooth without using extra cement complete all as specified and as directed. Note:-All necessary scaffolding arrangement if required at site up to four storeys height of bldgs shall be included in the quoted rate by the contractor & WPC shall be measured and paid separately.

Material and labour for rendering 15mm thick in CM 1:4 mixed with liquid water proofing compound (as per manufacturer’s instructions) in patches not exc 3 sqm each patch on fair faces of brick work ,concrete surface of wall, fin, facia, chajjas, parapet and similar article finished surface even and smooth without using extra cement complete all as specified and as directed. Note:-All necessary scaffolding arrangement if required at site up to four storeys height of bldgs shall be included in the quoted rate by the contractor & WPC shall be measured and paid separately.

Material and labour for preparation of newly plastered surfaces of wall and applying two coats of Cement Base Paint without any brush marks on the surface in any colour over and including a coat of alkali resistant primer (as per manufacturer’s recommendations) including curing before and after providing of each coat complete all as specified and as directed. Note:-All necessary scaffolding arrangement if required at site up to four storeys height of bldgs shall be included in the quoted rate by the contractor, all painted areas site to be cleaned and hand over as earlier without any extra cost to Govt, Shade/colour shall be approved by GE.

Material and labour for preparation of newly plastered surfaces of wall and applying two coats of exterior grade emulsion paint (weather proof/weather coat) without any brush marks on the surface in any colour over and including one coat of primer (as per manufacturer’s recommendations) complete all as specified and as directed. Note:- All necessary scaffolding arrangement if required at site up to four storeys height of bldgs shall be included in the quoted rate by the contractor,all painted areas site to be cleaned and hand over as earlier without any extra cost to Govt , Shade/colour shall be approved by GE.

Material and labour for rendering 15mm thick in CM 1:4 mixed with liquid water proofing compound (as per manufacturer’s instructions) on other than fair faces of brick work ,concrete surface of wall, fin, facia, chajjas, parapet and similar article finished surface even and smooth without using extra cement complete all as specified and as directed. Note:- All necessary scaffolding arrangement if required at site up to four storeys height of bldgs shall be included in the quoted rate by the contractor & WPC shall be measured and paid separately.

Material and labour for rendering 15mm thick in CM 1:4 mixed with liquid water proofing compound (as per manufacturer’s instructions) in patches not exc 3 sqm each patch on other than fair faces of brick work ,concrete surface of wall, fin, facia, chajjas, parapet and similar article finished surface even and smooth without using extra cement complete all as specified and as directed. Note:-All necessary scaffolding arrangement if required at site up to four storeys height of bldgs shall be included in the quoted rate by the contractor & WPC shall be measured and paid separately.

Supply only liquid water proofing compound complete all as specified and as directed.

Material and labour for preparation of newly plastered wall surface and applying three coats of white wash without any brush marks on the surface complete all as specified and as directed. Note:- All necessary scaffolding arrangement if required at site up to four storeys height of bldgs shall be included in the quoted rate by the contractor,all painted areas site to be cleaned and hand over as earlier without any extra cost to Govt.

Material and labour for 10mm thick rendering on brick work or concrete surfaces in CM 1:3 as in ceiling of roof slab,fin, facia, chajjas,parapet and similar article etc finishing surfaces even and smooth without using extra cement including necessary scaffolding up to four storeys height of bldgs if required complete all as specified and as directed.

Material and labour for 10 mm thick rendering on brick work or concrete surfaces in CM 1:3 in patches not exc 3 sqm each patch as in ceiling of roof slab,fin, facia, chajjas,parapet and similar article etc finishing surfaces even and smooth without using extra cement including necessary scaffolding up to four storeys height of bldgs if required complete all as specified and as directed.

Material and labour for preparation of newly plastered surfaces of ceiling and applying three coats of white wash without any brush marks on the surface complete all as specified and as directed. Note:- All necessary scaffolding arrangement if required at site up to four storeys height of bldgs shall be included in the quoted rate by the contractor,all painted areas site to be cleaned and hand over as earlier without any extra cost to Govt.

Material and labour for complete removal of existing treatment surface of wall and applying two coats of white wash on undecorated surface without any brush marks on the surface complete all as specified and as directed. Note:- All necessary scaffolding arrangement if required at site up to four storeys height of bldgs shall be included in the quoted rate by the contractor,all painted areas site to be cleaned and hand over as earlier without any extra cost to Govt.

Material and labour for preparation of old plastered or un-plastered surface of wall by brooming down or steel wire brushing,scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc and applying one coat of cement base paint of any colour without any brush marks on the surface complete all as specified and as directed. Note:- All necessary scaffolding arrangement if required at site up to four storeys height of bldgs shall be included in the quoted rate by the contractor,all painted areas site to be cleaned and hand over as earlier without any extra cost to Govt, Shade/colour shall be approved by GE & work will be in carried out in patches as directed.

Material and labour for complete removal of existing treatment surface of wall and applying two coats of Cement Base Paint without any brush marks on the surface in any colour over and including a coat of alkali resistant primer (as per manufacturer’s recommendations) complete all as specified and as directed. Note:- All necessary scaffolding arrangement if required at site up to four storeys height of bldgs shall be included in the quoted rate by the contractor,all painted areas site to be cleaned and hand over as earlier without any extra cost to Govt,Shade/colour shall be approved by GE & work will be in carried out in patches as directed.

Material and labour for preparation of old plastered or un-plastered surface of wall by brooming down or steel wire brushing,scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc and applying one coat of exterior grade emulsion paint (weather proof/weather coat) of any colour without any brush marks on the surface complete all as specified and as directed. Note:- All necessary scaffolding arrangement if required at site up to four storeys height of bldgs shall be included in the quoted rate by the contractor,all painted areas site to be cleaned and hand over as earlier without any extra cost to Govt, Shade/colour shall be approved by GE.

Material and labour for complete removal of existing treatment surface of wall and applying two coats of exterior grade emulsion paint (weather proof/weather coat) without any brush marks on the surface in any colour over and including one coat of primer (as per manufacturer’s recommendations) complete all as specified and as directed. Note:- All necessary scaffolding arrangement if required at site up to four storeys height of bldgs shall be included in the quoted rate by the contractor,all painted areas site to be cleaned and hand over as earlier without any extra cost to Govt, Shade/colour shall be approved by GE.

Taking down old heritage finish /Existing treatment and Preparation of old treated surface and Material & labour for applying based coat including two coat wall care putty on the surfaces and making surface absolutely smooth including primming coat and providing decorative Textures / coatings finish either in internal or external surfaces all as per manufacturer recommendations,in any colour, including necessary scaffolding up to four storeys height of bldgs if required,Texture /granular finish with any colours in any design & pattern in any shade and in any colour shall be approved by GE,all painted areas site to be cleaned and hand over as earlier without any extra cost to Govt complete all as specified and as directed.

Material and labour for Painting lines, dashes, arrows, letters, etc. on roads, pavements & the like exc 10cm wide with road marking paint, white or golden yellow or any colour etc including preparation of previously treated surfaces of road to receive the painting complete all as spd and directed. Note:- (a) The rates included for provision of red signals to keep off traffic from wet paint, cleaning road surface and working during odd hours when traffic is light. (b) 'The line painting shall stand out boldly and solidly without showing signs of brush marks or surface underneath. If necessary, the surface shall be repainted until the desired result is obtained as directed by GE & Shade/Colour shall be approved by GE & work will be in carried out in patches as directed.

Material and labour for applying one coat of synthetic enamel paint on brick, stone, concrete, asbestos cement or plaster surface of any description,in any colour, on any floor/wall surface over 10cm girth or width, not otherwise described,finished without brush mark on surface including preparation of old surface including necessary scaffolding up to four storeys height of bldgs if required,Shade/colour shall be approved by GE,all painted areas site to be cleaned and hand over as earlier without any extra cost to Govt complete all as specified and as directed & work will be in carried out in patches as directed.

Material and labour for applying two coat of synthetic enamel paint on brick, stone, concrete, asbestos cement or plaster surface of any description,in any colour, on any floor/wall surface over 10cm girth or width, not otherwise described,finished without brush mark on surface including preparation of old surface including necessary scaffolding up to four storeys height of bldgs if required,Shade/colour shall be approved by GE,all painted areas site to be cleaned and hand over as earlier without any extra cost to Govt complete all as specified and as directed & work will be in carried out in patches as directed.

Material and labour for preparation of old painted wooden surfaces of any description over 10 centimetre width or girth and applying one coat of synthetic enamel paint in any colour finished without brush mark on surface including necessary scaffolding up to four storeys height of bldgs if required, Shade/ colour shall be approved by GE, all painted areas site to be cleaned and hand over as earlier without any extra cost to Govt complete all as specified and as directed & work will be in carried out in patches as directed.

Material and labour for preparation of old painted steel and iron surfaces of any description over 10 centimeter width or girth and applying one coat of synthetic enamel paint in any colour finished without brush mark on surface including necessary scaffolding up to four storeys height of bldgs if required, Shade/ colour shall be approved by GE, all painted areas site to be cleaned and hand over as earlier without any extra cost to Govt complete all as specified and as directed & work will be in carried out in patches as directed.

M&L for preparation of new steel and iron surface of any description width or girth exc 10 cm and applying two coats of synthetic enamel paint over and including a coat of red oxide primer complete all as specified and directed.

Material and labour for cutting down plants / trees of girth not exc 15 cm & surface are not exc 0.36 Sqm each from roof tops /sides of external walls of buildings, chajja, wall junctions, junctions of of rain water / soil /waste vent pipes including taking out roots entered in wall/slab surfaces pouring chemical to burn out the root etc and making good the surfaces including repairing the CI/GI/PVC joints of affected locations by applying TUFALO (herbal medicine )and making good to suit the adjoining surfaces using PCC type 1:2:4, type B-O or cement mortar 1:2 complete all as per manufacturer instructions and as specified & work will be in carried out in patches as directed. Note:- Any CI/GI/PVC pipes and fittings damaged during work shall be replaced by new one to insure leakage / seepage free joint without any extra cost to the department and Unit rate quoted by tenderer shall included for use of all scaffolding, trestles, ladders, cradles etc ,hoisting, lowering and protective measures etc up to four storeys height of bldgs including Removing rubbish to a distance exc 500 m but not exc 1.5 km complete all as directed

Dismantling of intrlocking paver block/Stone slabs & tiles of any description or thickness in floors, aprons etc. Laid, bedded & pointed in any mortar complete all as specified and directed.

Material and labour for machine pressed precast concrete interlocking paver block any shape & size confirming to IS 15658-2006 of 60 mm thickness, M-35 grade rubber moulded glossy finish with grey cement and pigment complete all as secified and as directed. Note:- Shapes of interlocking paver block shall be triangular/Zigzag/ Haxagon/ or other, Colour of paver blocks, laying pattern approved by GE.

All as per srl item No. 138.00 here-in-before but except interlocking paver blocks. (Note: Old interlocking paver blocks retrieved from Dismantling shall be used).

Material and labour for machine pressed precast concrete interlocking paver block any shape & size confirming to IS 15658-2006 of 80 mm thickness, M-35 grade rubber moulded glossy finish with grey cement and pigment complete all as secified and as directed. Note:- Shapes of interlocking paver block shall be triangular/Zigzag/Haxagon/or other ,Colour of paver blocks,laying pattern approved by GE.

All as per srl item No. 140.00 here-in-before but except interlocking paver blocks. (Note: Old interlocking paver blocks retrieved from Dismantling shall be used).

Material and labour for 25mm thick sand filling under floors or in foundations including watering and consolidation or layer of sand cushioning below interlocking paver block complete all as specified and as directed.

M&L for cement concrete tile 30 cm x 30cm x 25 mm thick machine prerssed (coloured made in PVC mould with vibration process) set and jointed and pointed in neat cement slurry in floors with grey cement and pigment as reqd prelaminated for glossy finish over and including 15 mm thick screed bed in CM 1:4 complete all as specified and directed.

M & L for Non abrasive paving rectified (Endura) cement concrete coloured tiles of size 300x300x10 mm thick set jointed and pointed in neat cement slurry in floors with grey cement and no pigment laid over and including 15 mm thick screed bed in CM 1:4 complete all as specified and directed. Note:-The texture ,colour ,Shade of tiles & laying of tiles to any pattern & any design with one or more colours shall be approved by GE and Rates also including in this item for necessary raking circular cutting or notching and waste on tiles etc.

Dismantling floor, hearth or wall tiling including cement mortar bedding (But not backing) removing rubbish off the premises complete all as specified and directed.

Material and labour for glazed ceramic joint less coloured/Stone finish/digital/printed/High lighter tiles in vertical surface area exceeding 0.09 sqm but not exceeding 0.18 sqm set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile over & including 10mm thick backing coat/redering in cement mortar 1:4 for fixing of tiles complete all as specified and as directed. Note:- The texture ,colour ,size,Shade of tiles & laying of tiles to any pattern & any design with one or more colours shall be approved by GE and Rates also including in this item for necessary raking circular cutting or notching and waste on tiles.

M&L for Glazed ceramic Coloured tiles as in vertical/skirting/dado etc surface 300mmx200mmx 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over & including 10mm thick backing coat/redering in cement mortar 1:4 for fixing of tiles complete all as specified and as directed. Note:-The texture ,colour ,Shade of tiles & laying of tiles to any pattern & any design with one or more colours shall be approved by GE and Rates also including in this item for necessary raking circular cutting or notching and waste on tiles.

M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills,cooking platforms and like in CM(1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15 mm thick Screed bed in CM (1:4) complete all as specified and directed.

Demolition of PCC (unreinforced) in ground floors & pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Material and labour for 40 mm thick cement concrete type B1 1:2:4(20 mm graded aggregate) finished even and smooth without using extra cement as in flooring complete all as specified and directed.

supply only 38 mm wide and 3 mm thick glass dividing strips in flooring by fixing in position and making square or rectagle for casting concrete is flooring complete all as specified and directed.

M & L for 75 mm thick PCC 1:3:6 type C-1 using (20mm graded stone aggregate) as in plinth protection / hard standing /apron etc finished cement concrete surfaces even and fair and make impression with wire netting complete all as specified & directed.

M & L for 75mm thick plain Cement concrete 1:4:8, type D-2 using 40mm graded crushed stone aggregate as in sub base complete all as specified and as directed. Note:- Finishing surfaces of concrete to be even and rough to receive the topping layer

S&F in replacement Factory made Rectro reflective road sign comprising of plates of size 1500 x 900 mm fixed , one above the another made of 2 mm thick aluminum sheet duly framed in stainless steel 40mm bore pipe. The plates fixed with aluminium rivets and written on both side indicating the directions, alphabets, arrow, lines, diagrams etc on each sides with computrised cut letters and signs (reflective) as directed of approiate size and white in colour and dennison HIP base green. The boards (Plates) dully fitted with stainless steel 40 mm bore top height of boards with legs from ground level minmum 2.50m each including embedding in PCC (1:2:4) type B 1 block of size 30 Cm x 30cm x 60 cm including earthwork excavation and taking out old sign board any type all as per sample kept in GE office and as directed by Engr-in-charge (pegged sign board fully reflective). Make : GREEN LIGHT /GREEN /DARK EYE/ENS/ GUNNEBO/SHAKTI.

S&F in replacement Factory made Rectro reflective road sign boards comprising of plates of size 1200 x 800 mm fixed , one above the another made of 2 mm thick aluminum sheet duly framed in stainless steel 40mm bore pipe. The plates fixed with aluminium rivets and written on both side indicating the directions, alphabets, arrow, lines, diagrams etc on each sides with computrised cut letters and signs (reflective) as directed of approiate size and white in colour and dennison HIP base green. The boards (Plates) dully fitted with stainless steel 40 mm bore top height of boards with legs from ground level minmum 2.50m each including embedding in PCC (1:2:4) type B 1 (using 20mm graded crushed stone aggregate) block of size 30 Cm x 30cm x 60 cm including earthwork excavation and taking out old sign board any type all as per sample kept in GE office and as directed by Engr-in-charge (pegged sign board fully reflective). Make : GREEN LIGHT /GREEN /DARK EYE/ENS/ GUNNEBO/SHAKTI.

S&F in repairs Traffic convex Mirrors body colour black in Polycarbonate/ Stainless steel with Dome size 30" and 36" in Dia with GI pole of suitable height as per ground requirement and necessary earthwork, PCC 1:2:4 type B1 (using 20mm graded crushed stone aggregate) block size 0.45 x 0.45 x 0.60 metre for fixing of poles, location moving & etc as directed by GE. Make : GREEN LIGHT /GREEN /DARK EYE/ENS/ GUNNEBO/SHAKTI / VERTEX.

Notes :- (a) The contract sum shall be arrived at after deduction of amount of Schedule of Credit. (Rs. 59924.07). (b) PERFORMANCE SECURITY :- (Refer condition 19 of IAFW-2249) The performance security for an amount equivalent to 5% (Five percent) of the accepted contract sum shall be delivered by the successful bidder immediately after the date of intimation letter of acceptance and all provisions shall be applicable as per condition 19 of IAFW 2249.

malghotra construction co

VIKRAM SINGH MANHAS