SPL REPAIR TO BLDG NO P-39, T-25, T-3A AND T-4 UNDER AGE BR II AT GE JHANSI

Amount

Demolition of cement concrete (un-reinforced) incl terrazzo flooring in ground floor and paving not exceeding 15cm thickness (below or above ground level), complete all as specified and directed.

M&L for 75 mm thick cement concrete type D2 1:4:8 (using 40 mm graded stone agg) in sub base of flooring/ hard standing/wall complete all as specified and directed.

M&L 150 mm thick PCC 1:2:4, type B-2 (using 40mm graded stone aggregate) and finished even and fair without using extra cement complete all as specified and directed.

M&L for 75 mm thick cement concrete type C2 1:3:6 (using 40 mm graded stone agg) as in plinth protection and path laid in panels, not more than 3.0 mtr in length, laid to slope 1:30 incl forming joints 10mm wide and duly filled with mastic bitumen (01 part bitumen mixed with 03 parts of sand) surface, and finished surface even and fair, complete all as specified and as directed. (Note : The quoted rates are deemed to be inclusive of material against form work and joint fillings.)

M & L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M&L for factory made machine pressed precast concrete interlocking paver block of any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with coloured pigment made of PVC moulded (or rubber mould) with vibrating system, with and including 50mm thick sand cushioning, including in CM (1:3) in edges of pavers, complete all as specified and directed. (Note : The cost of sand cushion and plastering to edges is included in quoted rate.)

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises, complete all as specified and directed.

M&L for Non skid ceramic colored tiles , 7 to 8 mm thick (square / rectangular) area of each tile exc 0.06 sqm but n.exc 0.11 sqm as in flooring etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed/ bedding layer in CM (1:6) complete all as specified and as directed.

M&L for non-skid coloured ceramic tile, joint free 8 to 10 mm thick (square/rectangular) area of each tile not exceeding 0.36 sqm, in floors etc set and jointed in neat cement slurry over 15 mm thick screed bed or bedding layer in CM 1:6 over brushing neat cement slurry @ 3Kg/sqm etc complete all as speciefied and directed.

All as per item here-in-above but on vertical surfaces such as skirting/dado over and including 10mm thick CM rendering (backing coat) in CM 1:4,complete all as specified and as directed.

M&L for joint free, vitrified ceramic tiles of light shed 8-10 mm thick (square/rectangular) polished , area of each tile n.exc 0.36 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM (1:6) complete all as specified and as directed.

All as per item here-in-above but on vertical surfaces such as skirting/dado over and including 10mm thick CM rendering in CM 1:4,complete all as specified and as directed.

M&L for glazed ceramic coloured tiles in vertical surface of size 350 X 250 x 7/450x300x7 mm thick, jointless type, set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with and including 10 mm thick rendering in CM (1:4) for receiving the tiles, complete all as specified and as directed.

M & L for machine cut kota stone slab flooring 18-20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing over and including 15 mm thick screed bed in CM 1:4 complete all as specified and directed.

M & L for machine cut kota stone slab 18-22mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing over and including 10 mm thick backing coat in CM 1:3 complete all as specified and directed. Note: Kota stone in Step will be placed in single piece with groove lines at edge.

M&L 24/25 mm thick factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations, kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, including dismantling of old boarding, cupborad any description, fixed in any position including fittings , all as per direction of Engineer-In- Charge. (Note: stainless steel piano hinges/soft close clip on concealed hinges shall be paid separately)

Providing and fixing 2mm thick 18 to 25 mm wide PVC edge binding tape of approved quality for cupboard/wardrobe shutters including necessary synthetic resin hot pressed to edges on binding machine etc. complete as per directions of Engineer- in-charge.

Dismantling stone slabs and tiles of any description or thickness laid , bedded and pointed in any mortar as in floors, aprons etc. complete all as specified and directed.

M&L for 18-20 mm thick granite slab of any type , tabled rubbed, machine cut, duly grinding, polishing, moulding etc of all outer edges / sharp corners, duly fixed in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4), incl pointing in grey cement (1:2) using marble dust with admixture of pigment to match with the shade of slab, complete all specified and directed.

Dismantling of wall / ceiling boards (fiber, pulp, insulation etc) / insulation boards /slabs/blankets of any thickness including cover fillets etc, complete all as specified and directed.

S&F of exposed frame false ceiling system with GI powder coated grid consisting of interlocking arrangement of main T runner of 15mm size, suspended at 1200mm C/C and cross T runner of 15mm size suspended at 600mm C/C supported by 1.5mm dia GI wire from roof/Slab/truss incl wall/perimeter runner/channel of 15 mm size with and incl 4mm thick pre-painted non asbestos fiber reinforced cement board (E-board), designer type of size 595x595mm, duly fixed in ceiling frame work, complete all as specified and directed.

Dismantling boarding, cupborad any description, fixed in any position including fittings complete all as specified and directed.

M&L for 18/19 mm thick factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations, kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel piano hinges/soft close clip on concealed hinges shall be paid separately)

Supply only continuous (piano) hinges, mild steel bright finish in electro galvanized width of flat (when open) in 30mm, complete all as specified and directed

S&F drawer handles, projection drop (50mm to 65mm) on screwed plate of brass chromium plated, complete all as specified and directed

S&F 100 mm aluminium anodized hasp and staple, safety type, aluminium anodised with hinge pin including bolt to hinge plate and fixed with screw complete all as specified and directed

Supply & Fix stainless steel magnetic catcher fancy type for kitchen cabinet / drawer complete all as specified and directed.

Demolition of brick work built in cement mortar or lime mortar including all quoins, arches, pillars etc complete all as specified and directed.

M&L for brick work with old size fly ash bricks, straight or curved on plan exc. 6 M mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for half brick thick wall with old size fly ash bricks, straight or curved on plan to any radius built in cement mortar 1:4, complete all as specified and directed.

M&L for 10 mm rendering thick in CM (1:6) on fair faces of brick work/concrete surfaces finished even & smooth (without using extra cement), complete all as specified and directed.

M&L for 10 mm rendering thick in CM (1:6) on fair faces of brick work/concrete surfaces finished even & smooth (without using extra cement) including taking down cement plaster on brick or stone wall,dado and skirting etc including racking out joints hacking for key scrubbing down with water etccomplete all as specified and directed.

M&L for rendering 15mm thick in two coats (1st coat 10 mm thick in CM 1:6 & 2nd coat 5 mm thick in CM 1:4 with WPC) on fair faces of brick work/concrete surfaces, finished even & smooth (without using extra cement) including taking down cement plaster on brick or stone wall,dado and skirting etc including racking out joints hacking for key scrubbing down with water etc complete all as specified and directed. Note: WPC in 5 mm thick 2nd layer plaster measured and paid separately.

Blank in toto

Blank in toto

Blank in toto

M&L for rendering 15mm thick in two coats (1st coat 10 mm thick in CM 1:6 & 2nd coat 5 mm thick in CM 1:4) on fair faces of brick work/concrete surfaces, finished even & smooth (without using extra cement), complete all as specified and directed.

M&L for preparation of new plastered surface of wall and applying two coat of cement based paint over and incl one coat of exterior grade cement based primer, complete all as specified and directed.

M&L for preparation of new plastered of wall surface and applying two coats of oil bound distemper, over a coat of chalk whitening primer over and incl a layer 3mm thick of wall care putty to get even and smooth level finish on new plastered surface of internal wall, complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint (weather proof) of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces. complete all as specified and directed. Note : The contractor shall produce batch certificate & delivery challans directly from paint manufacturer to establish the authenticity of the material. The batch testing certificate shall be brought at the site along with paint manufacturer's drums with seal intact.

M&L for complete removal of existing treatment by brushing, washing, rubbing down, scraping from old treated surfaces of wall and applying two coat of oil bound distemper over a coat of chalk whitening primer, over and incl a layer of (JK/Birla) 3.0mm thick wall care putty to get smooth and level finish, complete all as specified and directed.

Blank in toto

M&L for complete removal of existing treatment and preparation of surfaces of walls by scrapping/sand paper rubbing and finally washing with watering and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint (weather proof) of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces. complete all as specified and directed. Note : The contractor shall produce batch certificate & delivery challans directly from paint manufacturer to establish the authenticity of the material. The batch testing certificate shall be brought at the site along with paint manufacturer's drums with seal intact.

S & F for Factory made double extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 65x125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made complete all as specified & directed.

S&F Factory made single 35 mm thick extruded WPC (Wood Polymer Composite) solid moulded flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.

M&L 30mm thick factory made solid WPC (Wood plastic composit) moulded gauged door shutter with wire mesh in any number of division with brown wood grain texture, including stainless steel wire shall mesh be fixed with 15x15 Square tube in side rails with screwing 8x28 heat metal zink coated screws can be remove or fie again of the shall be as per manufacture instruction complete all as specified and complete all as specified and complete all as specified and directed.

S &F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm prelaminated colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed.

S & F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and as directed.

Taking down chowkhats with shutters (without taking off shutters from the frame) area exc 1.5 sqm but not exceeding 4 sqm each including cutting holes in brick/ stone wall built in cement / lime mortar, embedded portion exc half brick but n.exc one brick for inserting new hold fast and making good the disturbed portion/surfaces, in CM 1:3 complete all as directed.

All as per item here-in-above but not exc 1.5 sqm each

Taking down shutters of any description not exc 01 Sqm each, complete all as specified and directed.

M&L for second class hard wood plain, solid, straight chowkhats and frame, wrought framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints and fixing, complete all as specified and directed.

Blank in toto

S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm thick prelaminated colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

M&L for powder coated ( minimum thickness of powder coating not less than 50 micron) aluminium frame for doors, windows, ventilators with one or more rebates, fabricated out of powder coated aluminium hollow square or rectangular section of required size incl necessary joining cleats, fixing screws etc complete, having size of frame for doors 100mm x45mm x 3.18 mm thick; for window 104mm x 45mm x 3mm thick; for ventilators 59mm x 33mm x 2.5mm, complete all as specified and directed.

S&F 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides and one face is covered with decorative face veneer with lipping/frame to match complete all as specified and directed.

M&L for 35mm thick 2nd class hard wood glazed & skeleton shutter (fully glazed or gauged) open rebated & prepared to receive glass, gauge etc (without sash bars) edges of framing plain, chamfered sash bar, or rounded, fitted with & mitred beads for securing glass/wiremesh etc, conforming to IS-1003 Part-I & II; size of members of shutters as specified in SSR Part-I section–8, clause 8.24(a) complete all as specified and directed.

Blank in toto

M&L for powder coated ( minimum thickness of powder coating not less than 50 micron) aluminium door shutters, aluminium section for top rail and styles 85mm x 45mm x 2.0mm thick; bottom rail 100mm x 45mm x 2mm thick and lock rail 100mm x 45mmx 2.0mm thick incl necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, incl powder coated aluminum hinges, powder coated aluminum snap beading, screws, handle , particle board, ACP sheet etc, complete all as specified and directed.

Blank in toto

Providing and fixing powder coated (minimum thickness of powder coating not less than 50 micron) anodized aluminium window and ventilator shutters, hung/sliding type without sash bars, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading,screws, anodised aluminium fittingssuch as peg stays 150 mm long (1 No.) hinges type B-21 100 mm long (2 nos.) suitable handle (1 no.) etc all as specified and directed .

S&F powder coated ( minimum thickness of powder coating not less than 50 micron) aluminium window shutter (three shutter) sliding type with frame of powder coated aluminium channel section suitable for sliding aluminium shutters weighing 0.55Kg/M of three channel including necessary joining cleats glazing clips rubber packing Powder coated aluminium shop beading screws with two shutter including 5mm thick coloured glass and one shutter with stainless steel wire gauze including necessary locking arrangement and handle etc; as specified etc complete all as specified and directed.

Blank in toto

Blank in toto

S&F of aluminium alloy anodized sliding door bolt 300mm (aldrop bolt) length with hasp staple and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all specified and directed

S&F of 100 mm size butt hinges, extruded aluminum alloy with galvanized mild steel pin type B-21 anodized complete all specified and directed

S&F of 150mm long barrel tower bolt aluminum anodized extruded section fixed with cadmium plated screws complete all as specified and directed.

S&F of 150mm aluminum handle cast type anodized complete all specified and directed.

S&F of mild steel ordinary rat tail rod pattern springs of size 300mm including roller and roller plate complete all as specified and directed

S&F of 140 mm door stopper of aluminium body and tongue anodized with hard drawn steel spring fixed in floor complete all as specified and directed.

M&L for cement concrete 1:2:4 type B1 (20mm graded stone aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, copings, bond stones, bed plates for hold fast and the like including weathering, slightly rounded or chamfered angles and throating, , complete all as specified and directed.

M&L for mild steel angles, bars, flats etc, as in hold fasts, pipe clamps, plain angle cleats for securing purlins, supports for stiffening of fencing, wall ties and similar small articles confirming to Fe-290 Gde E-165, complete all as specified and directed.

M & L for 2nd class hardwood for plain fillets, square, rectangular or triangular in section, clean sawn, secured with nails or brads sectional area not exc 3 sqcm complete all as specified and directed.

S&F of stainless steel wire cloth 0.56 mm in nominal dia of wire average width of aperture 1.18 mm and fixed with tinned tacks of stainless steel wire staples to steel shutters or fixed with wooden beads to wooden joinery, complete all as specified and directed.

M&L in repair for stainless steel curtain rod 25mm dia steel pipe cutting into length as required at site with and incl SS end caps/lobs and SS wall mounting brackets, complete all as specified and directed.

S&F of ringfit PVC (SWR) pipe of 110 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end as self socketed with an integral groove to hold the rubber gasket, with and incl rubber tighten gaskets, ringfit sockets etc, complete pipe duly fixed to wall, including taking down of eaves gutter and rain / waste water pipes including all fittings any size and pattern complete all as specified and directed.

S&F of PVC (SWR) pipe of 110 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end socketed, duly fixed with cement solvent etc, complete pipe duly laid in trenches or in floors, including taking down of eaves gutter and rain / waste water pipes including all fittings any size and pattern complete all as specified and directed.

S&F of PVC (SWR) pipe of 75 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end socketed, duly fixed with cement solvent etc, complete pipe duly laid in trenches or in floors, including taking down of eaves gutter and rain / waste water pipes including all fittings any size and pattern complete all as specified and directed.

S&F 110 mm bore PVC (SWR) bends of any radius, complete all as specified and directed.

S&F 75 mm bore PVC (SWR) bends of any radius, complete all as specified and directed.

S&F PVC(SWR) vent cowl 110mm bore, jointing to waste pipe, complete all as specified and directed.

M&L for PVC(SWR) gully trap 110mm bore, jointing to waste pipe, complete all as specified and directed.

S&F PVC(SWR) vent cowl 75mm, setting and jointing with solvent cement , complete all as specified and directed.

S&F in repairs PVC sandwich wall lining consisting of 5 mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specification complete all as specified and directed.

S&F PVC floor trap of 75 mm outlet, jointing to waste pipe, complete all as specified and directed.

S & F 15 mm bore Galvanized Steel tubes, medium grade fixed to walls and ceilings or laid in floors, concealed or open incl cutting of grooves including taking up or down with connections and fittings all as specified and directed

S & F 20 mm bore Galvanized Steel tubes, medium grade fixed to walls and ceilings or laid in floors, concealed or open incl cutting of grooves including taking up or down with connections and fittings all as specified and directed

Blank in toto

M&L for cutting chases, pinning in for concealed water tubing, not exc 10 cm girth and making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc complete all as specified and directed.

S&F of rotational moulded polyethylene cylindrical vertical with closed top water storage tank triple layered white colour 500 Ltr capacity with connecting nipple, hoisted and fixed in position on new or existing foundation and making GI tubing inlet or outlet connection, with and incl disconnecting and dismantling the existing un-serviceable PVC/RCC water tank on top of roof/slab of bldgs, complete all as specified and directed.

S&F of rotational moulded polyethylene cylindrical vertical with closed top water storage tank triple layered white colour 1000 Ltr capacity with connecting nipple, hoisted and fixed in position on new or existing foundation and making GI tubing inlet or outlet connection, with and incl disconnecting and dismantling the existing un-serviceable PVC/RCC water tank on top of roof/slab of bldgs, complete all as specified and directed.

S&F in repair 20 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed.

S&F in repair 20 mm dia of Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iorn pipe and fixed. (minium weight 20 mm-210 gms) etc, complete all as directed.

S&F in repair sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm

S&F in replacement of pillar taps, 15 mm dia, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with long screwed shanks and fly-nuts, complete all specified and directed.

S&F in replacement of long body bib cock, 15 mm dia with wall flange made of cast copper alloy, chromium plated, complete all specified and directed.

S&F in replacement of handshower (health faucet) with 8 mm dia, 1.0 mtr long flexible tube, wall hook and wall flange made of cast copper alloy, chromium plated fancy type, complete all specified and directed.

S&F in replacement of overhead shower of dia 125 mm round shape single flow, ABS body chrome plated fancy type, with and incl swivel type shower arm of 20mm dia with wall flange made of cast copper alloy, chromium plated fancy type, complete all specified and directed.

S&F in replacement of angular stop cock 15 mm dia with wall flange made of cast copper alloy, chromium plated type, complete all specified and directed.

S&F in replacement of stop cock with long shank and cup (concealed type), 15mm dia with wall flange, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe / unions, complete all as specified and directed.

S&F in replacement of bottle trap 32 mm size with 250 mm long wall connection pipe and wall flange made of cast copper alloy, chromium plated fancy type, complete all specified and directed.

S&F in repair SS grating of squre/round shape, overall size of 150x150mm with hinge type openable jali of 100 mm dia size with and incl fixing with CM to floor/nahani traps etc, complete all specified and directed.

S&F in replacement of toilet paper holder with flap made of cast copper alloy, chromium plated, complete all specified and directed.

S&F in replacement of towel rail 600 mm long D type between flange and wall bracket made of cast copper alloy, chromium plated, complete all specified and directed.

S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as directed.

S&F in replacement of PVC multipurpose cabinet mirror with front openable door of overall size 350 x 450 mm, complete all as specified and directed.

S&F in replacement of PVC waste pipe 32 mm dia 750 mm long with for wash hand basin or for kitchen sink, complete all as specified and directed.

Blank in toto

S&F in replacement of PVC connection 600 x 15mm dia PTMT (PVC), complete all as directed.

S&F in replacement of 10 ltr capacity PVC valve less symphonic action type flushing cistern, white, with inlet ball valve, float and handle with and including wall bracket, 32 mm dia PVC flush pipe and connected to squat pattern / pedestal pattern water closet, including all joints and making good to the wall & floor,complete all specified and directed.

S&F in replacement Vitreous China urinals, half stall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe, including urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe), complete with necessary fittings, complete all as directed.

S&F in replacement of 1st quality vitreous china squatting pan Orissa pattern of size 580x440 mm, white colour with integral foot rests water closet including flush pipe, P Trap and connecting cone but exluding flushing cistern, duly fixed in lime concrete bedding and making good of floor surface, complete all as directed.

S&F in replacement of 1st quality vitreous china ware European type WC with "P" or "S" type traps and same make plastic seat cover of white colour including flush pipe, fixing bolts etc and making good of the wall & floor surface, complete all as directed.

S&F in replacement of 1st quality vitreous china wash hand basin, white flat/angle back, size 550x400mm, complete including necessary cutting for and pinning in ends of brackets) with and including wall brackets, PVC waste pipe of 750mm long, CP waste coupling of 32mm dia size, complete all as specified and directed.

M&L for preparation of new steel or iron surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over and including a coat of red oxide primer complete all as specified and directed

M&L for preparing new or previously untreated surfaces of wood or wood based materials of any description not otherwise described exc 10 cm width or girth and applying two coat of synthetic enamel paint over and including a coat of pink primer and layer of putty/filling material to get smooth & level finish, complete all as specified and directed.

Dismantling asbestos cement (corrugated or semicorrugate etc) sheet in roof covering, complete all as specified and directed.

Dismantling timber scantling 40.0 sqcm and over in section in any position as in framed / unframed works such as roof purlins, rafters, fillets, ridges etc as in roof/ ceiling, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

S&F of pre-painted 0.50mm thick Gavalume Aluminium Zinc coating GI based corrugated / semi corrugated / trapezoidal steel sheet of any colour having tensile strength 550 MPa and AZ 150 grade as in roof covering/cladding to walls, fixed with self tapping screws, complete all as specified and directed.

S&F pre-painted Galvalume Aluminium Zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength 550 MPa and AZ 150 grade as in ridge of roof covering, fixed with self tapping screws, complete all as specified and directed.

M&L for structural steel Fe-410-W(Gde-E-250) quality A for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, complete all as specified and directed.

S & F steel ventilators with centre hung shutter including two pairs of brass cup pivots, catch spring and pulley wheel, complete all as specified and as directed.

S & F framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

S&F of glass, tinted type, 5.5 mm thick, each panes not exc 0.5 sqm, suitable for aluminium window / Ventilators / door opening and similar work, complete all as specified and directed.

S & F in repair aluminium (Extruded section) body door closer, hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 60 to 80 kg complete all as specified and as directed.

Supply only liquid Water proofing compound complete all as specified and as directed.

S&F in replacement of corner glass shelf 300 mm with Chromium plated bracket guard and railing and fixing accessories, complete all as directed.

Demolition of RCC Not exc 15cm thickness Roofs, floors (other than ground floors), beams staircases, landing, chajjas, Cover slab and similar suspended work

S&F in replacement of Brass CP connection 15mm dia and 45cm long with 2 Nos brass check nuts with washers for geyser, complete all as directed.

M&L for RCC M-20 (Nominal Mix) (20 mm stone agg) Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified.

M&L for mild steel deformed TMT bars 5 mm To 10mm dia (as in reinforcement) cut to length, bent to shape require including cranking, bending spirally for hooking for column, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for reinforced concrete pipe Class NP-2, 150mm dia with coller laid jointed with CM 1:3 incl breaking up any types of pipes complete all as specified and directed.

M&L for PCC 1:3:6 type C2 as in concrete bed to 150 mm bore drain pipe and over incl packing under haunching against the sides of pipes after pipe laid and tested complete all as specified & as directed.

M & L for rough finish formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

M&L for PCC 1:2:4 type B-1(using 20 mm graded crushed stone agg) in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs , water troughs and the like including weathering, slightly rounded for chamfered angles and throating complete all as specified as directed

M&L for plain cement concrete (1:4:8) Type D-2 using 40 mm graded aggregate in foundations, filling and mass concrete below wall complete all as specified and directed.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5 m depth, for foundation etc or for shafts, wells, cesspits, manholes, pier holes, etc n.exc 10 sqm on plan and n.exc 1.5 m in dedpth and getting out hard/dense soil complete all as specified and directed

M&L for Returning, filling in including spreading, levelling, watering and well ramming in layersnot exc 25 cm and getting in loose soil all as specified as directed.

M&L of removing excavated material nexc.50 m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as well as specified

M & L Reinforcement Cement concrete type B1 (1:2:4) using 20mm grades stone aggregate as in cover slab for drain & manholes etc. as directed incl use and waste of necessary form work complete all as spd.

M&L for two coat of synthetic enamel paint over one coat of red oxide, zinc chromiume on steel surface including preparation of new steel surface width or girth exc 10cm all as specified and directed.

M&L for preparing old painted steel surfaces of any description over 10 cm width or girth not otherwise described and applying two coat of synthetic enamel paint complete all as specified and directed.

M&L for soakage wells excavation in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M-25 concrete including intercepting chamber and screen chamber made of brick masonry in CM, RCC cover slab in M-25/ SFRC cover, interconnecting pipes of RCC/ DWC complete filled with brick bats of size 1.8 m dia X 4.8 m effective depth complete all as specified abd directed.

Taking up or down steel water tubing alongwith fittings and connections of 25 mm dia from any trenches/on walls/ceilings/floors or any description, complete all as specified and directed.

Supply and fix Gate Valve, screwed, 25 mm dia pipe complete.

Materials and labour for construction of brick masonry valve pit of internal dimension 90 x 90 x 90 cm depth with sub class new 'B' bricks in CM (1:4) and 10 mm thick plastering in CM (1:4), PCC (1:4:8) type D2 (Using 40 mm graded broken stone aggregate) as in foundation lean concrete, PCC (1:3:6) type CI (using 20 mm graded broken stone aggregate) as in bedding and copping MS frame with 40 x 40 x 6 mm angle iron 4 mm thick MS sheet cover plate with locking arrangements, hinges and two coats of synthetic enamel paint over one coat of red oxide primer including preparation of surface, three coats of white wash on plastered surface (exposed to view) including necessary excavation in soft loose, soil, returning filling in and removal of surplus soil to a distance not exceeding 50 m complete all as specified and and directed.

S&F of 24 Inch throat dia wind ventilator having strainless steel top, bottom, inner cover and 24 Nos high grade aluminum grade AA1200 fins and double fan & smoke and anti-shrinking locking system with 2mm thick UV treated gel coated FRP base plate in 1700 mm length. MAKE :- “Mukta Engineers , Kay-Kay Engineers, Krisha Eco Systems”

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. and removing materials to store for taking credit and making good disturbed surfaces of walls, floors, etc.complete all as specified and directed.

M&L for point wiring for Modular fittings complete with 1.5 Sqmm FRLS insulated, unsheathed, multistranded, 1100 Volts grade copper conductor cable single core conforming to IS:694 along with one run of 1.5 Sqmm FRLS insulated copper conductor cable green in colour for continuous earthing drawn through and including medium grade rigid PVC conduit conforming to IS:9537 (Pt-III) and its all accessories/junction boxes/ inspection covers etc of suitable size but not less than 20mm(OD), concealed in wall/ floor etc including provision of Modular cover plates with frames and 1.50 sq mm PVC insulated unsheathed stranded copper conductor (FRLS) cable for common earth and connecting to earth dolly all as specified and directed by Enrg-in-charge. (Note- rates of chasing/cutting & making goods shall be included in the unit rate) :-

One light point/ceiling fan/exhaust fan controlled by one switch

One 6A socket point controlled by one switch on independent board

One 6A socket point controlled by one switch on same board

All as per srl item no. 152 here-in-before but with 2.5 sq mm FRLS copper wire with 2.5 Sqmm FRLS copper earth wire for one 16 Amp socket point controlled by one 16 Amp switch on independent board.

All as per srl item no. 152 here-in-before but with 4 sq mm FRLS copper wire with 4 Sqmm FRLS copper earth wire for one 16 Amp socket point controlled by one 16 Amp switch on independent board.

M&L for Point wiring with 1.5 Sqmm FRLSHHinsulated, unsheathed, multistranded, 1100 Volts grade copper conductor cable single core conforming to IS:694 along with one run of 1.5 Sqmm FRLSH insulated copper conductor cable green in colour for continuous earthing drawn through in metallic black colour conduit medium grade conforming to IS:9537 (Pt-II) and its all accessories/junction boxes/inspection covers etc of suitable size but not less than 20mm(OD), surface in wall/floor etc. including provision of pressed steel terminal box of thickness not less than 18 SWG with earth dolly suitable with brass/GI screws for mounting switches, sockets, fan regulator etc. of any size as per site requirement for mounting -switches, sockets and covered with 3 mm thick phenolic laminated hylam sheet fixed specified and directed for the following points:

One light point controlled by one way one switch SP 6 Amp, 240 V.

All as per the above item herein before 2.5 Sqmm cable for 3 Pin 6/16 Amps switch socket outlet

Taking down submain wiring of any size any type and in any position metalic/non metallic PVC conduit of wooden batten complete all as specified and directed.

M&L for sub main wiring alongwith earth wire 2 runs x 6 sqmm + 1 run x 6 sqmm with FRLS insulated copper conductor, single core cable drawn through and including medium grade rigid PVC conduit ISI Marked conforming to IS:9537 (Pt-III) and its accessories / junction boxes/inspection covers etc of suitable size but not less than 20 mm concealed in all/floor etc all as specified and directed by Engr-in- charge

All as per srl item no. 156 here-in-before but 2 runs X 2.5 Sqmm + 1 run X 2.5 Sqmm. Note: Three runs of copper cable and one run of PVC conduit shall be measured as one unit length

All as per srl item no. 156 here-in-before but 2 runs X 4 Sqmm + 1 run X 4 Sqmm (earth wire). Note: Three runs of copper cable and one run of PVC conduit shall be measured as one unit length

Supply and fix FLP /WP switch / Isolator 10 Amps single pole ON/Off with terminal box comlete.

Supply and fix Flame proof weather proof switch socket & plug combined 16 A, 250 Volts (2P+Earth)

Supply and fixing LED light fitting 2x16 Watt flame proof, CMRI certified recommended for gas/ vapor group of IIA & IIIB, Zone 1 & 2 and IP 65 protection with die cast aluminum hosing with heat resistant toughened glass with LED tube light fixtures driver, holders, connector etc. Complete with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size.

Supply and fix LED Bulkhead fixture 40 Watt flame proof , CMRI certified recommended for gas/vapor of IIA & IIB, Zone 1 & 2 and IP 65 protection with die cast aluminium hosing with heat resistant toughened glass with LED bulk head fixture driver, holders, connector etc. complete etc. complete with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size.

Supply and fix flame proof / weather proof 4 way junction box dia 100x65 H complete.

Blank in toto

M&L for sub main wiring with four runs of 2x 2.5 Sqmm for phase and neutral 1100 volts grade single core PVC insulated unsheathed multistranded copper conductor ,drawn through and including metalic in Steel conduit ISI marked with all conduit accessories mounting on walls/roofs/floors etc with 1x2.5sqmm single core PVC insulated unsheathed with one copper conductor as earth wire complete all as specified and directed. Note:- 2 runs of 2.5 Sqmm cable, one run of 2.5 Sqmm cable and one run of conduit will be measured as one unit .

Taking down old and unserviceable distribution board any type / way / capacity including fuses, MCB's, insulator etc complete after removing all connection and making good the disturbed surface all as specified and directed by Engr-in-charge.

Supply and fix Flame proof / weather proof lighting distribution board of TPN 4 Way enclosure size (420x420x250mm) with complete internal bus bar & wiring up terminals. Incoming : MCB 4P, 63A - 01 No Outgoing: MCB , 1P, 6A - 12 Nos.

Supply and fix Flame proof / weather proof lighting distribution board of SPN 6 Way enclosure size (300x300x190mm) with complete internal bus bar & wiring up terminals. Incoming : MCB 2P, 32A - 01 No Outgoing: MCB , 1P, 6A -04 Nos.

Taking down old and unserviceable existing earth plates and GI pipes and all connected accessories of any size / type of earth plate & GI pipe complete all as specified complete and making good the disturbed surface to match the existing disturbed surface/finishes complete all as specified and as directed by Engineer-in-charge.

S&F of Modular switch 1 way 6A, 1 module 240V, 50Hz complete all as specified and directed.

S&F Fan step regulator, 120W - 2 module, 240V, 50Hz ISI marked with valid CML complete all as specified and directed.

S&F of Modular Socket, 6A - 2/3 pin combined 2 module 240V, 50Hz complete all as specified and directed.

S&F of Modular switch 1 way 16A, 1 module 240V, 50Hz complete all as specified and directed.

S&F of Modular Socket 6A/16A - 2/3 pin combined 2 module 240V, 50Hz complete all as specified and directed.

S&F angle holder, metal cased, bakelite body, 240 volts, ISI marked with valid CML complete all as specified and directed.

S&F Ceiling rose, three terminals, bakelite body, 240 volts, ISI marked with valid CML complete all as specified and directed.

Supply and fix of modular MCB protected plug and socket board in sheet steel enclosure with 20A rated mini MCB and 20A rated 3 pin plug, 240 V, 50 Hz complete including cutting the wall surfaces for flush mounting of socket board all as specified and directed.

S&F switch piano type, single pole, one way, 6 amps, 240 volts, ISI marked with valid CML complete all as specified and directed.

S&F electronic fan regulator socket type in 5 steps, 240V, 50Hz ISI marked with valid CML complete all as specified and directed.

S&F Socket 5 pin, 6 Amp, universal type, 240 volts, ISI marked with valid CML complete all as specified and directed.

S&F Switch piano type, single pole, one way, 16 amps, 240 volts, ISI marked with valid CML complete all as specified and directed.

S&F Socket, 6 pin, 6/16 Amp, multipurpose 240 volts, ISI marked with valid CML complete all as specified and directed.

Supply and fix of Lamp holder, angle type with metal ring, PVC/Polycarbonate body including taking down existing unserviceable lamp holder of any description complete all as specified and directed.

S&F of integrated LED batten 10 watt, 2 feet long, full white in Engineering plastic batten with white acrylic cover with built-in electronic driver, pre-wired and connecting up with twisted twin core flexible copper wire of 0.5sqmm from ceiling rose to connector of fitting complete all as specified and directed.

S&F of integrated LED batten 20 watt, 4 feet long, full white in Engineering plastic batten with white acrylic cover with built-in electronic driver, pre-wired and connecting up with twisted twin core flexible copper wire of 0.5sqmm from ceiling rose to connector of fitting complete all as specified and directed.

Supply and fix Decorative wall light of 07 Watt fixture made up of Polycarbonate and including connecting with 3 Core twisted flexible copper conductor cable of suitable size from celling rose all as specified and directed complete all as specified and directed by Engineer-in-Charge.

S&F LED Tube light fitting batten type 20W, 230W, efficiency 120 Lumens per watt, colour temperature 6500k (Cool White), Power factor grater than 0.9, Polycarbonate body, CRI 80, IP Rating, IP 20, THDv with in 5 % and THDi (8-10%) and integrated Electronic driver complete with al accessories internally Pre-wired and including connecting with 3 Core twisted flexible copper conductor cable of suitable size from celling rose all as specified and directed. Notes:- (i) The rate of three core twisted flexible copper conductor cable of suitable size for connection is included in this item and noting shall be paid extra on this account. (ii) Warranty for replacement of each LED lite fitting shall not be less than 2 years from the date of purchase. (iii) Date of purchase shall be marked on each fixture with permanent marker for redeeming warranty benefits.

Supply and fix LED Suspended Circular profile PS of Decorative and aesthetically ceiling suspended disk profile lighting suitable for indoor lighting with aluminium housing with polymer diffuser for optimum light output of 25 Watt of Make : Shakti Cat Part No SZSDSMX025-CYL or equivalent to Havells/Bajaj/wipro

S&F LED luminaire 600 mm x 600 mm, 36 watt, 220 V AC recessed type (Cool white & warm white) with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling/grid ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and as directed by Engineer-in-Charge.

Supply and fix in replacement of LED bulkhead luminaire 10W in die-cast aluminium alloy/ PVC body heat resistant prismatic glass cover, with specially designed gasket for minimum IP 55 degree of protection complete all as specified and directed by Engineer-in-Charge.

Supply and fix LED building security light fitting 35 watts, Luman efficacy of LED 140 lm/W, PF>0.95 THD<10%, colour temperature 6500K CRI > 7, system luman not less then 2600 lm, made up of pressure die cast aluminium housing with high efficiency LED as lighting source and lens with toughed glass having bottom separate driver compartment with IP 65 protection and impact resistant of IK 07 etc and all accessories previewed complete including mounting bracket of GI Pipe 40mm inner dia light grade of reqd length and shape including bending, forging or welding etc and suitable bolts and nuts with washers, including connecting with PVC insulated multistandered cooper flexible cable of size 0.5sqmm 3 core form celling rose to fitting al as specified and directed. Notes:- (i) The rate of three core twisted flexible copper conductor cable of suitable size for connection is included in this item and noting shall be paid extra on this account. (ii) Warranty for replacement of each LED lite fitting shall not be less than 2 years from the date of purchase.

Taking down ceiling fan/exhaust fan of any sweep complete all as specified and directed by Engr-in-charge.

S&F of ceiling fans complete with blades, down rods, (with remote) and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value more than 6.00 BEE. Five star rated with brushless direct current motor (BLDC) all as specified and directed by Engineer-in-Charge.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers etc complete.

Supply and fix air circulator fan 230 volts single phase oscillating 450 mm sweepconsist of 100% Copper motor built in thermal overload protector aerodynamically balanced blades 3 speed regulation rust free bodyof speed 1350 RPM and air delivery 65CMM suitable for wall mounting complete.

Supply and fix electric water heater, storage type steel body with Strainless steel inner tank and heating element upto 2 KW Capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate,NRV, connection piece etc.

Taking down unserviceavle VTPN/ TPN DB with MCB's of any make/capacity complete all as specified and directed by Engr-in-Charge.

S&F of MCCB / MCB distribution board, Vertical TPN, 4 way, 415 V, 3 phase, AC with MCCB as incomer and MCBs as outgoing in sheet steel powder painted enclosure double door type with minimum IP 43 degree of protection with built in copper bus bar, neutral link and earth link complete including cutting the wall surfaces for flush mounting of DB and making good with cement plaster, putty and paint to match with the existing surfacecomplete all as specified and directed. Note: MCCB / MCBs shall be measured and paid separately.

Taking down unserviceavle Sheet metal box & MCB DB SPN with MCB's of any make/capacity complete all as specified and directed by Engr-in-Charge.

Taking down old unserviceable of LT cable of any size complete all as specified and directed by Engr-in-Charge.

Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with XLPE insulated stranded aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or strip and overall PVC sheathed, 16 sq mm 4 core ISI Marked as per IS 7098(Part 1) including connecting on LT panel based with suitable lugs, glands etc of any description complete all as specified and directed.

Supply and fix MCB distribution board, SPN, 8 way 230 Volt in sheet steel powder painted enclosure double door type with IP 43 degree of protection with built in copper bus bar, neutral link and earth link complete including cutting the wall surfaces for flush mounting of DB and making good with cement plaster, putty and paint to match with the existing surface all as specified and directed by Engineer-in-Charge. Note: MCBs shall be measured and paid separately.

All as per item No. 28 here-in-before but SPN, 4 way, 230 V, 1 phase, AC Note: MCBs shall be measured and paid separately.

S&F MCCB, Four Pole 63A, with breaking capacity 16 KA, adjustable thermal and fixed magnetic type, ics=100%icu, 415 volt including connection with suitable size aluminium/ copper lugs complete all as specified and directed by Engr-In-Charge.

S& F of MCB SPN 40Amp , 10KA, SPN 'C' curve, 240 V, 50 Hz complete all as specified and directed.

S&F MCB TPN 63A, 415 V, 50 Hz, with breaking capacity 10 KA, C series complete all as specified and directed.

S& F MCB SPN 40-63 Amp, 240 V with breaking capacity 10 KA, 'C' series complete all as specified and directed.

S& F MCB SP 6-32 Amp, 240 V with breaking capacity 10 KA, 'C' series complete all as specified and directed.

M&L for earthing complete with galvanized iron earth plate electrode 600mm x 600mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5 meters below normal ground level connecting to GI wire 4 mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanized iron or steel and earth wire protected by 15mm dia GI pipe medium grade and connected to distribution board/earthing test point all as shown in electrical plate No. 3 of SSR Part-I(2009) and testing on completion complete all as specified and directed. Note :- (i) The unit rate quoted shall also include for excavation, earth work in any type of soil, plain cement concrete 1:3:6 mix, Type C1 pit, 40mm thick RCC 1:2:4 mix type B1 cover reinforced with 8mm dia TMT bras @ 150mm C/C both ways, GI funnel with watering pipe, wire mesh, protection pipe, earth wire up to 7.50m long complete in addition to item No. 1(a) to (e) of preamble (Notes) under sub heading earthing, specified in SSR Part II. (ii) Contract must ensure earthing test result less than 5 Ohm and submitted test report to Engr-in-Charge.

Supply and fixed with wall / ceiling / roof/ floor etc including fixing accessories of XLPE insulated ,armoured heavy duty electric cable with aluminium conductor , 1100 volts grade ,cross sectional area 4 core 25 sqmm including with cable gland, thimbling etc. complete.

Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with XLPE insulated stranded aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or strip and overall PVC sheathed,35 sq mm 4 core ISI Marked as per IS 7098(Part 1) including connecting on LT panel based with suitable lugs, glands etc including taking down existing cable of any description complete all as specified and directed.

Material and labour for Double wall corrugated HDPE pipe, ISI marked of outer dia 50mm, inner dia 38mm with smooth internal and profiled external surface, non-pressure type, laid in trenches/floors/duct or fixed on walls /pole including all connections, accessories like socket, couplers, bends, etc for protection of LT cable XLPE grade 1100 volts complete all as specified and directed by Engineer-in-Charge.

Taking down old U/S earthing and M&L for Earthing complete with galvanised iron earth plate electrode 600mm x 600mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtrs deep below ground level) with top edge of the plate not less than 1.5 mtrs below normal ground level connecting to GI wire 4 dia mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel and earth wire protected by 15mm dia GI pipe medium grade and connected to distribution board/earthing test point all as shown in electircal plate No. 3 of SSR Part-I(2009) and testing on completion complete all as specified and directed. Note :- The unit rate quoted shall also include for excavation, earth work in any type of soil, plain cement concrete 1:3:6 mix, Type C1 pit, 40mm thick RCC 1:2:4 mix type B1 cover reinforced with 8mm dia TMT bras @ 150mm C/C both ways, GI funnel with watering pipe, wire mesh,protection pipe, earth wire upto 7.50m long complete in addition to item No. 1(a) to (e) of preamble (Notes) under sub heading earthing, specified in SSR Part II.

Flint India (BID ID -3508722)