PROVN OF REPLACEMENT OF OH LINE TO UG CABLE FROM BURDONG TO MS-13 UNDER GE GANGTOK

Amount

Dismantling of ACSR from any location complete all as specified and directed.

Dismantling HT / LT Overhead Copper conductor line from any location complete all as specified and directed.

Dismantling insulators any type, any size complete all as directed .

Dismantling cross-arms of M.S. channel or angle sections etc. complete all as directed.

Dismantling stay assembly complete all as specified and directed .

Dismantling of poles/ struts, any size complete all as specified and directed .

Materials & labour including testing XLPE insulated, screened, PVC bedded,galvanised steel strip or wire armoured, electric power cables (heavyduty) with aluminium conductor, 11000 volts Earthed,grade cross sectional area 95 sq. mm, 3 core complete all as specified and directed. (Note:-1. Earthwork & Excavation ,GI pipe,DWC pipe etc shall be measured and paid seperately under relevant items of this BOQ. 2. Supply and fixing for cable route marker 100mm dia cast iron route marker duly marked voltage grade including grouting with PCC are included in unit rate.3.The unit rate quoted by the bidder shall deemed to be included of the cost of aluminium thimbles/lugs of suitable sizes).

Supply, installation, Testing and commissioning of Energy Metre for 11 KV (HTS Consumer) of accuracy class 0.2S as per ISI, 4697-99 and 485 Modbus communication port equipped with MDI facility (premier 300, 3-phase, 4 wire with PTR-/110V and CTR-/5A , Acc Cls 0.2S , a. Modem b. Sheet metal meter box (outdoor type) c. GPRS Modem with RS 232 optical cable all accessories. (ECD210 GSM/GPRS Modem with serial RS 232 /RS-485 Data cable d. 2.5 Sq.mm 4 core PVC copper control cable and other miscellaneous items required e. Safe earthing model T-388short time current 50 KA RMS for sec (EHV) applcaition n80 mm dia x 3 mtr electrode & two bags back fill chemical compound. f. 11 KV compsite metering unit consisting of 11 KV PT(3 ph 4 wire) and duplex type CT as per load with class of accurancy 0.2 S (100/50/5A) g. GPRS enabled sim card . h. Materials rquired for replacement of 11 KV compsite metering unit either on parapet or of poletop channel, back clamps nuts & bolts as per requirements depending on site condition. (Note:- Work shall be executed as per direction by Energy & Power Deptt ,Govt of Sikkim and proof of the direction shall be kept of record.)

Materials & Labour Cable jointing kit for 11 KV (Earthed) grade cable for indoor termination cold shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 50 Sqmm to 95 Sqmm complete all as specified and directed.(Note:- (i) Earthwork & Excavation, GI pipe, DWC pipe etc shall be measured and paid separately under relevant items of this schedule. (ii) The unit rate quoted by the bidder shall deemed to be included of the cost of aluminium thimbles/lugs of suitable sizes. (iii) S&F for cable route marker 100 mm dia cast iron route marker duly marked voltage grade incl grouting with PCC are incl in unit rate).

Materials & labour including jointing & testing XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 6 sq. mm 2 core complete all as specified & as directed. Note:- (i) Earthwork & Excavation, GI pipe, DWC pipe etc shall be measured and paid separately under relevant items of this schedule.(ii) The unit rate quoted by the bidder shall deemed to be inclusive of the cost of aluminium thimbles/lugs of suitable sizes. (iii) Supply and fixing for cable route marker 100mm / 80 mm suitable dia cast iron route marker duly marked voltage grade including grouting with PCC will be included in quoted the rate.

Materials & labour including jointing & testing XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 16 Sqmm 4 core complete all as specified & as directed. Note:- (i) Earthwork & Excavation, GI pipe, DWC pipe etc shall be measured and paid separately under relevant items of this schedule.(ii) The unit rate quoted by the bidder shall deemed to be inclusive of the cost of aluminium thimbles/lugs of suitable sizes. (iii) Supply and fixing for cable route marker 100mm / 80 mm suitable dia cast iron route marker duly marked voltage grade including grouting with PCC will be included in quoted the rate.

Materials & labour including jointing & testing XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 25 Sqmm 4 core complete all as specified & as directed. Note:- (i) Earthwork & Excavation, GI pipe, DWC pipe etc shall be measured and paid separately under relevant items of this schedule.(ii) The unit rate quoted by the bidder shall deemed to be inclusive of the cost of aluminium thimbles/lugs of suitable sizes. (iii) Supply and fixing for cable route marker 100mm / 80 mm suitable dia cast iron route marker duly marked voltage grade including grouting with PCC will be included in quoted the rate.

Materials & labour including jointing & testing XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 35 Sqmm 3.5 core complete all as specified & as directed. Note:- (i) Earthwork & Excavation, GI pipe, DWC pipe etc shall be measured and paid separately under relevant items of this schedule.(ii) The unit rate quoted by the bidder shall deemed to be inclusive of the cost of aluminium thimbles/lugs of suitable sizes. (iii) Supply and fixing for cable route marker 100mm / 80 mm suitable dia cast iron route marker duly marked voltage grade including grouting with PCC will be included in quoted the rate.

Materials & labour including jointing & testing XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 50 Sqmm 3.5 core complete all as specified & as directed. Note:- (i) Earthwork & Excavation, GI pipe, DWC pipe etc shall be measured and paid separately under relevant items of this schedule.(ii) The unit rate quoted by the bidder shall deemed to be inclusive of the cost of aluminium thimbles/lugs of suitable sizes. (iii) Supply and fixing for cable route marker 100mm / 80 mm suitable dia cast iron route marker duly marked voltage grade including grouting with PCC will be included in quoted the rate.

Materials & labour including jointing & testing XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 70 Sqmm 3.5 core complete all as specified & as directed. Note:- (i) Earthwork & Excavation, GI pipe, DWC pipe etc shall be measured and paid separately under relevant items of this schedule.(ii) The unit rate quoted by the bidder shall deemed to be inclusive of the cost of aluminium thimbles/lugs of suitable sizes. (iii) Supply and fixing for cable route marker 100mm / 80 mm suitable dia cast iron route marker duly marked voltage grade including grouting with PCC will be included in quoted the rate.

Materials & labour including jointing & testing XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 95 Sqmm 3.5 core complete all as specified & as directed. Note:- (i) Earthwork & Excavation, GI pipe, DWC pipe etc shall be measured and paid separately under relevant items of this schedule.(ii) The unit rate quoted by the bidder shall deemed to be inclusive of the cost of aluminium thimbles/lugs of suitable sizes. (iii) Supply and fixing for cable route marker 100mm / 80 mm suitable dia cast iron route marker duly marked voltage grade including grouting with PCC will be included in quoted the rate.

Materials & labour including jointing & testing XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 120 Sqmm 3.5 core complete all as specified & as directed. Note:- (i) Earthwork & Excavation, GI pipe, DWC pipe etc shall be measured and paid separately under relevant items of this schedule.(ii) The unit rate quoted by the bidder shall deemed to be inclusive of the cost of aluminium thimbles/lugs of suitable sizes. (iii) Supply and fixing for cable route marker 100mm / 80 mm suitable dia cast iron route marker duly marked voltage grade including grouting with PCC will be included in quoted the rate.

Materials & labour including jointing & testing XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 150 Sqmm 3.5 core complete all as specified & as directed. Note:- (i) Earthwork & Excavation, GI pipe, DWC pipe etc shall be measured and paid separately under relevant items of this schedule.(ii) The unit rate quoted by the bidder shall deemed to be inclusive of the cost of aluminium thimbles/lugs of suitable sizes. (iii) Supply and fixing for cable route marker 100mm / 80 mm suitable dia cast iron route marker duly marked voltage grade including grouting with PCC will be included in quoted the rate.

Materials & labour including jointing & testing XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 185 Sqmm 3.5 core complete all as specified & as directed. Note:- (i) Earthwork & Excavation, GI pipe, DWC pipe etc shall be measured and paid separately under relevant items of this schedule.(ii) The unit rate quoted by the bidder shall deemed to be inclusive of the cost of aluminium thimbles/lugs of suitable sizes. (iii) Supply and fixing for cable route marker 100mm / 80 mm suitable dia cast iron route marker duly marked voltage grade including grouting with PCC will be included in quoted the rate.

Materials & labour including jointing & testing XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 240 Sqmm 3.5 core complete all as specified & as directed. Note:- (i) Earthwork & Excavation, GI pipe, DWC pipe etc shall be measured and paid separately under relevant items of this schedule.(ii) The unit rate quoted by the bidder shall deemed to be inclusive of the cost of aluminium thimbles/lugs of suitable sizes. (iii) Supply and fixing for cable route marker 100mm / 80 mm suitable dia cast iron route marker duly marked voltage grade including grouting with PCC will be included in quoted the rate.

Materials & labour including jointing & testing XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 300 Sqmm 3.5 core complete all as specified & as directed. Note:- (i) Earthwork & Excavation, GI pipe, DWC pipe etc shall be measured and paid separately under relevant items of this schedule.(ii) The unit rate quoted by the bidder shall deemed to be inclusive of the cost of aluminium thimbles/lugs of suitable sizes. (iii) Supply and fixing for cable route marker 100mm / 80 mm suitable dia cast iron route marker duly marked voltage grade including grouting with PCC will be included in quoted the rate.

Materials & labour including jointing & testing XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 400 Sqmm 3.5 core complete all as specified & as directed. Note:- (i) Earthwork & Excavation, GI pipe, DWC pipe etc shall be measured and paid separately under relevant items of this schedule.(ii) The unit rate quoted by the bidder shall deemed to be inclusive of the cost of aluminium thimbles/lugs of suitable sizes. (iii) Supply and fixing for cable route marker 100mm / 80 mm suitable dia cast iron route marker duly marked voltage grade including grouting with PCC will be included in quoted the rate.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out soft/loose soil complete all as specified & as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm soft/loose soil complete all as specified and as directed

Removing excavated material (Soils) n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed.

Supplying and laying of DWC HDPE pipe .lSI marked in trenches or in cable ducts or fixed on walls using clamps along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. of size 50 mm outer dia complete all as directed.

Supplying and laying of DWC HDPE pipe .lSI marked in trenches or in cable ducts or fixed on walls using clamps along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. of size 63 mm outer dia complete all as directed.

Supplying and laying of DWC HDPE pipe .lSI marked in trenches or in cable ducts or fixed on walls using clamps along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. of 75 mm outer dia complete all as directed.

Supplying and laying of DWC HDPE pipe .lSI marked in trenches or in cable ducts or fixed on walls using clamps along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. of 90 mm outer diacomplete all as directed.

Supply and laying 40 mm bore GI pipe light grade including fittings fixed to pole/laying under road crossing with clamps complete for cable protection all as specified and as directed

Supply and laying 80 mm bore GI pipe light grade including fittings fixed to pole/laying under road crossing with clamps completefor cable protection all as specified and as directed

Supply and laying 150 mm bore GI pipe light grade including fittings fixed to pole/laying under road crossing with clamps complete for cable protection all as specified and as directed

M & L Plain cement concrete (1:3:6) type C-1 using 20 mm graded stone aggregates as finishing road/concrete surface including finishing to exposed concrete surfaces even and fair complete all as specified.

S & F Astronomical Timer for Street lights control 40 amps TPN complete all as specified.

M & L Steel tubular swaged poles complete with cast iron base plate, finial taper plug, bolts, nuts & screws as specified type 410 SP-22 (8.5 metres long) all as specified and as directed.(Note:-(a) The unit rates include staying the poles in a truly vertical position till the foundations are properly set.(b) Excavation, foundation concrete, presenative treatment, etc.will be measured separately under the appropriate sections.Painting to steel tubular poles (inside and outside) is however included in the rates of steel tubular poles.(c) The unit rates for poles shall also apply to struts when poles of the same size are used as struts.(d) The Unit Rates for steel tubular poles also include provision of finial and cast iron base plate fixed to poles.(e) The unit rates also include drilling of holes in steel tubular poles and hooks for continuous G.I. earth wire etc. to the required size and number.(f)The pipe incorporated for steel tubular poles shall be from the makes as indicated under Makes/manufacturer of GI Pipes).

Supply, install, comissioning and testing of LT feeder Pillar outdoor(CPRI Approved) type weather proof dust/vermin proof Powder Coated Cubical panel made out of 3mm CRCA sheet and with angle iron 40mmX40mmX6mm frame . Factory made fabricated duly powder coated, front openable and rear openable door with locking arrangements with the following acessories including taking down the old unsv panel disconnecting Existing cables & Reconnecting the cables to new panels Vertical Copper bus bar 200 Amps min for 3 phase and Neutral ,Distance between Two Bus Strips -25mm (min) (for pump house at burdong):-a. Main incoming MCCB FP 125 Amps, 415 Volts, 25 KA - 01 Each b. MCB TPN 32 Amps 415 Volt 10 KA - 02 Each c. MCB TPN 16 Amps 415 Volt 10 KA - 02 Each d. MCB TPN 10 Amps 415 Volt 10 KA - 01 Each e. MCB TPN 06 Amps 415 Volt 10 KA - 02 Each f. MCB SPN 16 Amps 240 Volt 10 KA - 01 Each g. Digital Ammeter - 01 Each h. Digital Voltmeter - 01 Each j. RYB Indicators - 1 Set k. Insulated cable glands for entry of cable to panel - 03 Each Note: Panel maker be CPRI approved. Flooring and mounting of panel to a newly constructed platform of suitable size shall be measured and paid for seperately

Supply, install, comissioning and testing of LT feeder Pillar outdoor type (CPRI Approved) weather proof dust/vermin proof Powder Coated Cubical panel made out of 3mm CRCA sheet and with angle iron 40mmX40mmX6mm frame . Factory made fabricated duly powder coated, front openable and rear openable door with locking arrangements with the following acessories including taking down the old unsv panel disconnecting Existing cables & Reconnecting the cables to new panels Vertical aluminium bus bar 150 Amps min for 3 phase and Neutral ,Distance between Two Bus Strips -25mm(min) as directed :- a. Main incoming MCCB FP 100 Amps, 415 Volts, 25 KA - 01 Each b. MCB TPN 32 Amps 415 Volt 10 KA - 02 Each c. MCB TPN 20 Amps 415 Volt 10 KA - 01 Each d. MCB TPN 10 Amps 415 Volt 10 KA - 01 Each e. MCB TPN 06 Amps 415 Volt 10 KA - 01 Each f. Digital Ammeter - 01 Each g. Digital Voltmeter - 01 Each h. RYB Indicators - 1 Set j. Insulated cable glands for entry of cable to panel - 06 Each Note: Panel maker be CPRI approved. Flooring and mounting of panel to a newly constructed platform of suitable size shall be measured and paid for seperately

Supply, install, comissioning and testing of LT feeder Pillar outdoor type (CPRI Approved) weather proof dust/vermin proof Powder Coated Cubical panel made out of 3mm CRCA sheet and with angle iron 40mmX40mmX6mm frame . Factory made fabricated duly powder coated, front openable and rear openable door with locking arrangements with the following acessories including taking down the old unsv panel disconnecting Existing cables & Reconnecting the cables to new panels Vertical aluminium bus bar 250 Amps min for 3 phase and Neutral ,Distance between Two Bus Strips -25mm(min) as directed :- a. Main incoming MCCB FP 160 Amps, 415 Volts, 25 KA - 01 Each b. MCB TPN 40 Amps 415 Volt 10 KA - 01 Each c. MCB TPN 32 Amps 415 Volt 10 KA - 01 Each d. MCB TPN 20 Amps 415 Volt 10 KA - 04 Each e. MCB TPN 16 Amps 415 Volt 10 KA - 01 Each f. MCB TPN 06 Amps 415 Volt 10 KA - 01 Each g. MCB SPN 06 Amps 240 Volt 10 KA - 01 Each h. Digital Ammeter - 01 Each j. Digital Voltmeter - 01 Each k. RYB Indicators - 1 Set l. Insulated cable glands for entry of cable to panel - 10 Each Note: Panel maker be CPRI approved. Flooring and mounting of panel to a newly constructed platform of suitable size shall be measured and paid for seperately

Supply, install, comissioning and testing of LT feeder Pillar outdoor type (CPRI Approved) weather proof dust/vermin proof Powder Coated Cubical panel made out of 3mm CRCA sheet and with angle iron 40mmX40mmX6mm frame . Factory made fabricated duly powder coated, front openable and rear openable door with locking arrangements with the following acessories including taking down the old unsv panel disconnecting Existing cables & Reconnecting the cables to new panels Vertical aluminium bus bar 100 Amps min for 3 phase and Neutral ,Distance between Two Bus Strips -25mm(min) as directed :- a. Main incoming MCCB FP 63 Amps, 415 Volts, 25 KA - 01 Each b. MCB TPN 16 Amps 415 Volt 10 KA - 01 Each c. MCB TPN 10 Amps 415 Volt 10 KA - 01 Each d. MCB TPN 06 Amps 415 Volt 10 KA - 02 Each e. MCB SPN 06 Amps 415 Volt 10 KA - 01 Each f. Digital Ammeter - 01 Each g. Digital Voltmeter - 01 Each h. RYB Indicators - 1 Set j. Insulated cable glands for entry of cable to panel - 06 Each Note: Panel maker be CPRI approved. Flooring and mounting of panel to a newly constructed platform of suitable size shall be measured and paid for seperately

Supply, install, comissioning and testing of LT feeder Pillar outdoor type (CPRI Approved) weather proof dust/vermin proof Powder Coated Cubical panel made out of 3mm CRCA sheet and with angle iron 40mmX40mmX6mm frame . Factory made fabricated duly powder coated, front openable and rear openable door with locking arrangements with the following acessories including taking down the old unsv panel disconnecting Existing cables & Reconnecting the cables to new panels Vertical aluminium bus bar 200 Amps min for 3 phase and Neutral ,Distance between Two Bus Strips -25mm(min) as directed :- a. Main incoming MCCB FP 125 Amps, 415 Volts, 25 KA - 01 Each b. MCB TPN 16 Amps 415 Volt 10 KA - 01 Each c. MCB TPN 32 Amps 415 Volt 10 KA - 01 Each d. MCB TPN 40 Amps 415 Volt 10 KA - 01 Each e. MCB TPN 06 Amps 415 Volt 10 KA - 01 Each f. MCB SPN 06 Amps 240 Volt 10 KA - 01 Each g. Digital Ammeter - 01 Each h. Digital Voltmeter - 01 Each j. RYB Indicators - 1 Set k. Insulated cable glands for entry of cable to panel - 06 Each Note: Panel maker be CPRI approved. Flooring and mounting of panel to a newly constructed platform of suitable size shall be measured and paid for seperately

Supply, install, comissioning and testing of LT feeder Pillar outdoor type (CPRI Approved) weather proof dust/vermin proof Powder Coated Cubical panel made out of 3mm CRCA sheet and with angle iron 40mmX40mmX6mm frame . Factory made fabricated duly powder coated, front openable and rear openable door with locking arrangements with the following acessories including taking down the old unsv panel disconnecting Existing cables & Reconnecting the cables to new panels Vertical aluminium bus bar 150 Amps min for 3 phase and Neutral ,Distance between Two Bus Strips -25mm(min) as directed:- a. Main incoming MCCB FP 100 Amps, 415 Volts, 25 KA - 01 Each b. MCB TPN 32 Amps 415 Volt 10 KA - 01 Each c. MCB TPN 20 Amps 415 Volt 10 KA - 01 Each d. MCB TPN 16 Amps 415 Volt 10 KA - 01 Each e. MCB TPN 06 Amps 415 Volt 10 KA - 01 Each f. MCB SPN 06 Amps 240 Volt 10 KA - 01 Each g. Digital Ammeter - 01 Each h. Digital Voltmeter - 01 Each j. RYB Indicators - 1 Set k. Insulated cable glands for entry of cable to panel - 06 Each Note: Panel maker be CPRI approved. Flooring and mounting of panel to a newly constructed platform of suitable size shall be measured and paid for seperately

Supply, install, comissioning and testing of LT feeder Pillar outdoor type (CPRI Approved) weather proof dust/vermin proof Powder Coated Cubical panel made out of 3mm CRCA sheet and with angle iron 40mmX40mmX6mm frame . Factory made fabricated duly powder coated, front openable and rear openable door with locking arrangements with the following acessories including taking down the old unsv panel disconnecting Existing cables & Reconnecting the cables to new panels Vertical aluminium bus bar 80 Amps min for 3 phase and Neutral ,Distance between Two Bus Strips -25mm(min) as directed:- a. Main incoming MCCB FP 36 Amps, 415 Volts, 16 KA - 01 Each b. MCB TPN 16 Amps 415 Volt 10 KA - 01 Each c. MCB TPN 10 Amps 415 Volt 10 KA - 02 Each d. MCB TPN 06 Amps 415 Volt 10 KA - 01 Each e. MCB SPN 06 Amps 240 Volt 10 KA - 01 Each g. Digital Ammeter - 01 Each h. Digital Voltmeter - 01 Each j. RYB Indicators - 1 Set k. Insulated cable glands for entry of cable to panel - 06 Each Note: Panel maker be CPRI approved. Flooring and mounting of panel to a newly constructed platform of suitable size shall be measured and paid for seperately

Supply, install, comissioning and testing of LT feeder Pillar outdoor type (CPRI Approved) weather proof dust/vermin proof Powder Coated Cubical panel made out of 3mm CRCA sheet and with angle iron 40mmX40mmX6mm frame . Factory made fabricated duly powder coated, front openable and rear openable door with locking arrangements with the following acessories including taking down the old unsv panel disconnecting Existing cables & Reconnecting the cables to new panels Vertical aluminium bus bar 80 Amps min for 3 phase and Neutral ,Distance between Two Bus Strips -25mm(min) as directed:-a. Main incoming MCCB FP 32 Amps, 415 Volts, 16 KA - 01 Each b. MCB TPN 16 Amps 415 Volt 10 KA - 01 Each c. MCB TPN 10 Amps 415 Volt 10 KA - 01 Each d. MCB SPN 06 Amps 240 Volt 10 KA - 01 Each e. Digital Ammeter - 01 Each f. Digital Voltmeter - 01 Each g. RYB Indicators - 1 Set h. Insulated cable glands for entry of cable to panel - 04 Each Note: Panel maker be CPRI approved. Flooring and mounting of panel to a newly constructed platform of suitable size shall be measured and paid for seperately

Supply, install, comissioning and testing of LT feeder Pillar outdoor type (CPRI Approved) weather proof dust/vermin proof Powder Coated Cubical panel made out of 3mm CRCA sheet and with angle iron 40mmX40mmX6mm frame . Factory made fabricated duly powder coated, front openable and rear openable door with locking arrangements with the following acessories including taking down the old unsv panel disconnecting Existing cables & Reconnecting the cables to new panels Vertical Copper bus bar 150 Amps min for 3 phase and Neutral ,Distance between Two Bus Strips -25mm(min) as directed:- a. Main incoming MCCB FP 100 Amps, 415 Volts, 25 KA - 01 Each b. MCB TPN 20 Amps 415 Volt 10 KA - 01 Each c. MCB TPN 16 Amps 415 Volt 10 KA - 01 Each d. MCB TPN 10 Amps 415 Volt 10 KA - 04 Each e. MCB SPN 06 Amps 240 Volt 10 KA - 01 Each g. Digital Ammeter - 01 Each h. Digital Voltmeter - 01 Each j. RYB Indicators - 1 Set k. Insulated cable glands for entry of cable to panel - 08 Each Note: Panel maker be CPRI approved. Flooring and mounting of panel to a newly constructed platform of suitable size shall be measured and paid for seperately

Supply, install, comissioning and testing of LT feeder Pillar outdoor type (CPRI Approved) weather proof dust/vermin proof Powder Coated Cubical panel made out of 3mm CRCA sheet and with angle iron 40mmX40mmX6mm frame . Factory made fabricated duly powder coated, front openable and rear openable door with locking arrangements with the following acessories including taking down the old unsv panel disconnecting Existing cables & Reconnecting the cables to new panels Vertical Copper bus bar 150 Amps min for 3 phase and Neutral ,Distance between Two Bus Strips -25mm(min) as directed :- a. Main incoming MCCB FP 100 Amps, 415 Volts, 25 KA - 01 Each b. MCB TPN 20 Amps 415 Volt 10 KA - 02 Each c. MCB TPN 10 Amps 415 Volt 10 KA - 03 Each d. MCB TPN 06 Amps 415 Volt 10 KA - 02 Each e. MCB SPN 06 Amps 240 Volt 10 KA - 01 Each g. Digital Ammeter - 01 Each h. Digital Voltmeter - 01 Each j. RYB Indicators - 1 Set k. Insulated cable glands for entry of cable to panel - 09 Each Note: Panel maker be CPRI approved. Flooring and mounting of panel to a newly constructed platform of suitable size shall be measured and paid for seperately

Supply, install, comissioning and testing of LT feeder Pillar outdoor type(CPRI Approved) weather proof dust/vermin proof Powder Coated Cubical panel made out of 3mm CRCA sheet and with angle iron 40mmX40mmX6mm frame . Factory made fabricated duly powder coated, front openable and rear openable door with locking arrangements with the following acessories including taking down the old unsv panel disconnecting Existing cables & Reconnecting the cables to new panels Vertical Copper bus bar 100 Amps min for 3 phase and Neutral ,Distance between Two Bus Strips -25mm(min) as directed:- a. Main incoming MCCB FP 63 Amps, 415 Volts, 25 KA - 01 Each b. MCB TPN 10 Amps 415 Volt 10 KA - 01 Each c. MCB TPN 06 Amps 415 Volt 10 KA - 05 Each d. MCB SPN 06 Amps 240 Volt 10 KA - 01 Each e. Digital Ammeter - 01 Each f. Digital Voltmeter - 01 Each g. RYB Indicators - 1 Set h. Insulated cable glands for entry of cable to panel - 08 Each Note: Panel maker be CPRI approved. Flooring and mounting of panel to a newly constructed platform of suitable size shall be measured and paid for seperately

Supply, install, comissioning and testing of LT feeder Pillar outdoor type ( CPRI approved) weather proof dust/vermin proof Powder Coated Cubical panel made out of 3mm CRCA sheet and with angle iron 40mmX40mmX6mm frame . Factory made fabricated duly powder coated, front openable and rear openable door with locking arrangements with the following acessories including taking down the old unsv panel disconnecting Existing cables & Reconnecting the cables to new panels Vertical Copper bus bar 150 Amps min for 3 phase and Neutral ,Distance between Two Bus Strips -25mm(min) as directed :-a. Main incoming MCCB FP 100 Amps, 415 Volts, 25 KA - 01 Each b. MCB TPN 10 Amps 415 Volt 10 KA - 04 Each c. MCB TPN 06 Amps 415 Volt 10 KA - 03 Each d. MCB SPN 06 Amps 240 Volt 10 KA - 01 Each e. Digital Ammeter - 01 Each f. Digital Voltmeter - 01 Each g. RYB Indicators - 1 Set h. Insulated cable glands for entry of cable to panel - 09 Each Note: Panel maker be CPRI approved. Flooring and mounting of panel to a newly constructed platform of suitable size shall be measured and paid for seperately

Supply, install, comissioning and testing of LT feeder Pillar outdoor type (CPRI approved) weather proof dust/vermin proof Powder Coated Cubical panel made out of 3mm CRCA sheet and with angle iron 40mmX40mmX6mm frame . Factory made fabricated duly powder coated, front openable and rear openable door with locking arrangements with the following acessories including taking down the old unsv panel disconnecting Existing cables & Reconnecting the cables to new panels Vertical Copper bus bar 200 Amps min for 3 phase and Neutral ,Distance between Two Bus Strips -25mm(min) as directed:-a. Main incoming MCCB FP 125 Amps, 415 Volts, 25 KA - 01 Each b. MCB TPN 20 Amps 415 Volt 10 KA - 01 Each c. MCB TPN 10 Amps 415 Volt 10 KA - 03 Each d. MCB TPN 06 Amps 415 Volt 10 KA - 07 Each e. MCB SPN 06 Amps 240 Volt 10 KA - 01 Each g. Digital Ammeter - 01 Each h. Digital Voltmeter - 01 Each j. RYB Indicators - 1 Set k. Insulated cable glands for entry of cable to panel - 13 Each Note: Panel maker be CPRI approved. Flooring and mounting of panel to a newly constructed platform of suitable size shall be measured and paid for seperately

Supply, install, comissioning and testing of LT feeder Pillar outdoor type (CPRI approved) weather proof dust/vermin proof Powder Coated Cubical panel made out of 3mm CRCA sheet and with angle iron 40mmX40mmX6mm frame . Factory made fabricated duly powder coated, front openable and rear openable door with locking arrangements with the following acessories including taking down the old unsv panel disconnecting Existing cables & Reconnecting the cables to new panels Vertical aluminium bus bar 80 Amps min for 3 phase and Neutral ,Distance between Two Bus Strips -25mm(min) (MES md accd new cantt -panel 1):- a. Main incoming MCCB FP 40 Amps, 415 Volts, 25 KA - 01 Each b. MCB TPN 16 Amps 415 Volt 10 KA - 01 Each c. MCB TPN 10 Amps 415 Volt 10 KA - 01 Each d. MCB SPN 06 Amps 240 Volt 10 KA - 01 Each e. Digital Ammeter - 01 Each f. Digital Voltmeter - 01 Each g. RYB Indicators - 1 Set h. Insulated cable glands for entry of cable to panel - 04 Each Note: Panel maker be CPRI approved. Flooring and mounting of panel to a newly constructed platform of suitable size shall be measured and paid for seperately

Supply, install, comissioning and testing of LT feeder Pillar outdoor type ( CPRI approved ) weather proof dust/vermin proof Powder Coated Cubical panel made out of 3mm CRCA sheet and with angle iron 40mmX40mmX6mm frame . Factory made fabricated duly powder coated, front openable and rear openable door with locking arrangements with the following acessories including taking down the old unsv panel disconnecting Existing cables & Reconnecting the cables to new panels Vertical aluminium bus bar 500 Amps min for 3 phase and Neutral ,Distance between Two Bus Strips -25mm(min) (MES md accd new cantt -panel 2) :-a. Main incoming MCCB FP 320 Amps, 415 Volts, 36 KA - 01 Each b. MCCB FP 80 Amps, 415 Volts, 16 KA - 02 Each c. MCCB FP 32 Amps, 415 Volts, 16 KA - 02 Each d. MCB TPN 10 Amps 415 Volt 10 KA - 01 Each e. MCB SPN 06 Amps 240 Volt 10 KA - 01 Each g. Digital Ammeter - 01 Each h. Digital Voltmeter - 01 Each j. RYB Indicators - 1 Set k. Insulated cable glands for entry of cable to panel - 06 Each Note: Panel maker be CPRI approved. Flooring and mounting of panel to a newly constructed platform of suitable size shall be measured and paid for seperately

Supply, install, comissioning and testing of LT feeder Pillar outdoor type (CPRI approved ) weather proof dust/vermin proof Powder Coated Cubical panel made out of 3mm CRCA sheet and with angle iron 40mmX40mmX6mm frame . Factory made fabricated duly powder coated, front openable and rear openable door with locking arrangements with the following acessories including taking down the old unsv panel disconnecting Existing cables & Reconnecting the cables to new panels Vertical aluminium bus bar 500 Amps min for 3 phase and Neutral ,Distance between Two Bus Strips -25mm(min) (ORs and MES md accd feeder panel) :- a. Main incoming MCCB FP 320 Amps, 415 Volts, 36 KA - 01 Each b. MCCB FP 100 Amps, 415 Volts, 25 KA - 02 Each c. MCCB FP 63 Amps, 415 Volts, 16 KA - 01 Each d. MCB TPN 32 Amps 415 Volt 10 KA - 01 Each e. MCB TPN 16 Amps 415 Volt 10 KA - 01 Each g. Digital Ammeter - 01 Each h. Digital Voltmeter - 01 Each j. RYB Indicators - 1 Set k. Insulated cable glands for entry of cable to panel - 06 Each Note: Panel maker be CPRI approved. Flooring and mounting of panel to a newly constructed platform of suitable size shall be measured and paid for seperately

Supply, install, comissioning and testing of LT feeder Pillar outdoor type (CPRI approved ) weather proof dust/vermin proof Powder Coated Cubical panel made out of 3mm CRCA sheet and with angle iron 40mmX40mmX6mm frame . Factory made fabricated duly powder coated, front openable and rear openable door with locking arrangements with the following acessories including taking down the old unsv panel disconnecting Existing cables & Reconnecting the cables to new panels Vertical aluminium bus bar 300 Amps min for 3 phase and Neutral ,Distance between Two Bus Strips -25mm(min) as directed:-a. Main incoming MCCB FP 200 Amps, 415 Volts, 36 KA - 01 Each b. MCCB FP 125 Amps, 415 Volts, 25 KA - 01 Each c. MCB FP 25 Amps, 415 Volts, 10 KA - 01 Each d. MCB TPN 06 Amps 415 Volt 10 KA - 01 Each e. MCB SPN 06 Amps 240 Volt 10 KA - 01 Each g. Digital Ammeter - 01 Each h. Digital Voltmeter - 01 Each j. RYB Indicators - 1 Set k. Insulated cable glands for entry of cable to panel - 05 Each Note: Panel maker be CPRI approved. Flooring and mounting of panel to a newly constructed platform of suitable size shall be measured and paid for seperately

Supply, install, comissioning and testing of LT feeder Pillar outdoor type (CPRI approved) weather proof dust/vermin proof Powder Coated Cubical panel made out of 3mm CRCA sheet and with angle iron 40mmX40mmX6mm frame . Factory made fabricated duly powder coated, front openable and rear openable door with locking arrangements with the following acessories including taking down the old unsv panel disconnecting Existing cables & Reconnecting the cables to new panels Vertical aluminium bus bar 320 Amps min for 3 phase and Neutral ,Distance between Two Bus Strips -25mm(min) as directed:-a. Main incoming MCCB FP 125 Amps, 415 Volts, 25 KA - 01 Each b. MCB TPN 32 Amps 415 Volt 10 KA - 02 Each c. MCB TPN 16 Amps 415 Volt 10 KA - 02 Each d. MCB TPN 10 Amps 415 Volt 10 KA - 02 Each e. MCB TPN 06 Amps 415 Volt 10 KA - 02 Each f. MCB SPN 06 Amps 240 Volt 10 KA - 01 Each h. Digital Ammeter - 01 Each j. Digital Voltmeter - 01 Each k. RYB Indicators - 1 Set l. Insulated cable glands for entry of cable to panel - 9 Each Note: Panel maker be CPRI approved. Flooring and mounting of panel to a newly constructed platform of suitable size shall be measured and paid for seperately

Supplying, installing, testing and commissioning of 16 M high Mast system with the following spacifications:- (a) Supply installation testing and commission of high mast shaft shall be in Two section hot dip galvanized , inside and outside in single dip, suitable for wind velocity as per IS:875 Part-3. There shall be only one longitudinal seam section and no circumferential weld. it shall also include accessories for high mast including head frame, 2 point suspension system with steel wire rope 6 " dia (7/19 constrution) duble drum winch, galvanized lantem carriage arrangement suitable for up to 9 luminaries symmetrically tighting final & integral power tool for raising and lowering operation of the high mast. (b) Supply of foundation bolts manufactured from special steel alongwith nuts,washers, anchor, plates & templates as recommended by High mast manufacturer (c) Fixing of LED light fitting 1x200 watt complete set-08 Nos (d) Supply of twin dome aviation obstruction lights of type with Neon lamp as recommended by High mast manufacturer . (e) Supply of control panel housing suitable control circuit for automatic switching ON and OFF of the MAST. It shall also have suitable control for operation of power tool. (f) Construction of suitable shallow foundation with RCC 1:1.5:3 using 20 mm stone aggregate concrete for the high mast considering the safe soil bearing capacity at site as 10 T/Sqm at 2 mtr depth with all materail and labour. (g) Erection of the high mast with help of suitable equipment and wiring of luminaires with all wiring materail and labour. (h) Provision of GI electorde 60cm x 60 cm x 6mm earthing for high mast with earthing lead with 4 mm GI wire complete- 02 Nos. (j) Installation of control panel on suitable foundation including all materail and labour. (k) Testing and commissioning of above high mast system. Note: The drawing of high mast light shall be got approved from GE before execution the work. Luminaires shall be measured and paid separately under relevant item.

Supply and fix LED flood light of 200 Watts for High Mast light complete all as specified as directed.

S&F street light fitting on pole for use with LED lamps, 60 watt, 240 volt, 6000K, with high quality lenses and reflector, high grade alluminium pressure die cast housing with toughened glass cover, IP-66 glas of protection , roadway luminaries with high power LED as a light source complete with control gear and accessories provn of connecting wire with multi stranded copper conductor 1.5 sqmm nominal cross sectional area, single core, PVC insulated and unsheathed FRLS cable 1100 volts grade, ISI 694 mark with valid CML NO in and incl PVC conduit pipe, accessories etc. Connected upto street light junction box incl bracket of GI pipe light grade of dia equal to size of fitting, 1.2 mtr long bend in required shape, MS clamps 40x3mm thick duly painted with 2 coats of synthetic enamel paint and as directed .

S & F loop in- loop junction box of internal dimension 155 x 210 x 92 mm made out of polycarbonate and locking arrangement incl 6 Amps MCB - 1 No, 20 Amps rated 4 way connectors for 3 phase and neutral incoming/out going, mounted in the box, fixing on steel tubular poles including necessary clamps, suitable glands, lugs and GI nut and bolts including taking down old unserviceable junction box complete all as specified and directed.

M & L of earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6.00 mm thick buried directly in ground [earth pit not less than 2.25 metre deep below normal ground level] with top edge of the plate electrode not less than 1.5 m below normal ground level, connected to including galvanised iron strip size 32 x 6 mm by means of bolts, nuts, and washers of galvanized iron or steel all as shown in electrical plate No. 3 of SSR Part I connected to earth test point including provision of earth strip protected by 40 mm dia light grade GI pipe & watering pipe shall be 20 mm bore medium grade GI pipe including all excavation and earth work in any type of strata, PCC pit with RCC cover, CI frame, char coal, salt & funnel etc complete all as specified or indicated including testing on completion all as specified and directed . (Note: Unit Rate to be considered for earth strip to be fixed 7.5m long)

Note 1:- (Applicable for all parts/items) : The bidders/contractors are advised to read tender document, all drawings & all corrigendum/ amendments and general condition of contracts before entry/quoting the rates. Note 2:- Attention to bidder is hereby invited to upload revised BOQ if published during their bid submission. Uploading of incorrect/ pre-revised BOQ shall be treated as non bonafide and rejected.

M/S R. K. INDUSTRIES

Garg Brothers

HAMTECH ENGINEERING PRIVATE LIMITED

KANISHKA ENTERPRISES

M/s BHAGWATI CONSTRUCTION

SANJAY SAW MILL

S K ENTERPRISES