SPECIAL REPAIR TO CERTAIN NC E BILLET, TOILETS AND ANNEXE AND ADDN/ALTN AIRMEN MESS AT AF STN UTARLAI

Amount

M&L S&F Coloured Non Skid ceramic tiles 7 to 8mm thick joint less (squares/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed in CM(1:6) with including dismantling of tiling with cement mortar bedding complete all as specified and directed.

M&L for glazed ceramic tiles size 300X450X7mm thick on vertical surface over 10mm thick rendering in CM (1:4) such as dado/skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match with coloured including dismantling of tiling with cement mortar bedding complete all as specified and directed.

Taking down existing roof treatment any thickness including plastering, leaping plaster of any thickness cuting & up rooting tree roots/Vegitation growth & removing the debris from the premises upto 500m from the MOD land including cleaning/washing down and keeping surfaces clean complete all as specified and as directed.

M & L for 10 mm thick screed bed in cement mortar 1:4 complete mixed with 2 % water proofing compound as per manufacturers instructions (note:Water proofing compound shall be measured and paid seprerately under respective item) over roof top surface finished even and smooth using extra cement and application of water proofing treatment using APP modified roof membrane over existing accessible RCC roof slab / chajjah / canopy / parapet wall to be executed through approved applicator of the membrane manufacturer with following specification etc complete all as specified and directed :- (a) Cleaning existing surface properly. (b) Applying oil bound bitumen primer @ 0.30 litre / Sqm manufactured by the same agency as that of APP membrane with a density 0.87-0.89 Kg per liter at 25 degree centigrade on prepared surface. (c) Laying not less than 3mm thick APP modified water proofing membrane weighing not less than 3.00 Kg/Sqm reinforced with non woven polyster fiber weight not less than 160gsm/Sqm using butane torch by torch application with 10cm side laps and 15cm end lap. Physical property of membrane shall be as under :- (d) APP membrane shall be laid using butane torch by Torch application with minimum 10cm side overlap and 15cm end lap. (Note:- WPC shall be measured and paid separately)

M&L for rendering in cement plaster in 15 mm thick on fair faces of brick work with mixing @3% by wt of cement finished fair & even in CM 1:4 including taking down old cement plaster, recking out joints, scrrubing down with water complete all as specified and directed( WPC will measurement and paid separately).

M&L for 15mm thick cement plaster in CM (1:6) on other than fair faces of brick work finished even and fair with out using extra cement including taking down old cement plaster, racking out joints, scrrubing down with water complete all as specified and directed.

M&L for rendering 5 mm thick on fair faces of brick work or concrete surface of ceiling in cement mortar 1:3 finished even & smooth (without using extra cement) including taking down old cement plaster, racking out joints, scrubing down with water complete all as specified and directed

M&L for preperation of newly plastered ceiling surface & applying three coat of white wash on ceiling surface complete all as specified and directed.

Supply only integral water proofing compound complete all as specified and directed.

Demolition of PCC in ground floors & pavings n exc 15 cm thickness (below or above ground level) (unreinforced) complete all as specified and directed.

M&L for 75mm thick cement concrete type C-2 (1:3:6) (using 40 mm graded stone aggregate ) as in plinth protection and path finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel/PVC tubing and connections including cleaning for refixing old tubing and connection in new or old position for 15mm bore complete all as specified and directed

Taking up or down steel/PVC tubing and connections including cleaning for refixing old tubing and connection in new or old position for 20mm bore complete all as specified and directed

Taking up or down steel/PVC tubing and connections including cleaning for refixing old tubing and connection in new or old position for 25mm bore complete all as specified and directed

S&F 15mm bore tubes medium grade galvanized with all fittings and fixed complete to walls (concealed) ceilings or laid in floors including taking down old tubing complete all as specified and directed

S&F 20mm bore tubes medium grade galvanized with all fittings and fixed complete to walls(concealed) ceilings or laid in floors including taking down old tubing complete all as specified and directed

S&F 25mm bore tubes medium grade galvanized with all fittings and fixed complete to walls(concealed) ceilings or laid in floors including taking down old tubing complete all as specified and directed

S&F in repair PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets flush pipe of polyethylene of low or high density of PVC, 32mm dia for low level cistern complete all as specified and directed

S&F in repair Stop valves 15 mm bore fancy type, CP with long shank & cup (conncelaed type), cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed

S&F in repair 15 mm angle stop valve chromium plated fancy type complete all as specified and as directed.

S&F in repairs CP Bib taps 15 mm bore long body, cast copper alloy with crtuch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule fancy type complete all as specified and directed.

S&F in repairs Vitreous China squatting pan, `Orrisa' pattern, size 580 x440 mm white, with integral foot rests (excluding flushing cistern & flush pipe) complete all as specified and directed.

S&F in repair PVC connections 15mm size with PTMT nuts of length 600 mm complete all as specified and directed.

S&F in repair brass chromium plated shower roses with swivel joints 125mm size in square with CP long shank arm including fixing to steel pipe or union complete all as specified and as directed.

S&F in repair Chromium plated Towel rail with towel racks of 600mm long of fixed with & including CP brass screws & wooden/plastic cleats (min. weight 190gms) complete all as specified and directed.

S&F in repair CP Grating doom 100 mm dia with or without hole complete all as specified and directed.

S&F Rotational moulded polyethylene white colour water storage tanks (cylindrical vertical with closed top) hoisted & fixed in position all as specified in SSR Part I 500 Ltrs Capacity with 20mm dia PTMT float valve incl Dismantling water tanks & removing to store complete all as specified and directed.

S&F Rotational moulded polyethylene white colour water storage tanks (cylindrical vertical with closed top) hoisted & fixed in position all as specified in SSR Part I 1000 Ltrs Capacity with 20mm dia PTMT float valve incl Dismantling water tanks & removing to store complete all as specified and directed.

S&F in repair Gun-metal, globe or gate valves 20mm bore, with iron wheel head, screwed both end for iron pipe complete all as specified and directed.

S&F in repair wash hand basin vitreous china wash basin white flat back size 550x400 including supplied and fixed angle iron brakets errecting stand, CP waste coupling, waste pipe complete all as specified.

S & F in Repair 15mm bore pillar taps pressematic type (push tap) with aerator and wall flange automatically off with delay,fancy type ,long body ,cast copper alloy ,with capstan heads ,chromium plated ,screwed down high pressure with or without lettered Hot or Cold with long screw shanks and fly nuts screwed for iron pipe and necessary connecting parts(union/T/elbow) of tap complete all as specified and directed.

S&F sheet glass corner self (of 3 tier )assembly consisting of 5.5mm thick sheet glass self 15cm radius with chromium plated bracket guard and rail and fixed with CP screws and wood cleats with wall complete all as specified and directed.

M&L for 25mm dia stainless steel curtain rod with brackets and knobs at both ends as per site requirement including taking down old existing PVC curtain rods with accessories complete all as specified and directed by Engr-in-charge. Note : The cost of brackets and knobs is deemed to be including in the quoted rate. Nothing extra shall be paid on this account.

Demolition of stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc. and removing from site all as specified and directed.

M&L for 20cm thick precast cement concrete 1:3:6, type C-1 using 20mm graded stone aggregate block masonry with solid block, exc 10 cm in width & set in CM 1:6 all as specified & as directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames exc 1.5 sq. m but n exc 4 sqm each

Taking down chowkhat with shutter (without taking off shutter from the frame) n. exc 1.5 sqm all as specified.

Taking down shutters of any description exc 1 Sqm & nexc 2 Sqm each complete all as specified.

S&F solid PVC door frame of size 50x47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube supplying and fixing in door opening as per specification and drawings.

S&F factory made solid panel PVC door shutter 30mm thick (style ) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded colour plain PVC or channel having a PVC sheet strip of 20mm width stuch in side with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert top rail & bottom rail panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement supplying & fixing in the frame at site as per specification & drawing.

S&F 30 mm thick flush shutters factory made solid core construction with block boards core and plywood face panels, commercial type on both sides (ISI marked) fixed to chowkhats complete all as specified and directed.

S&F 35mm th 2nd class Hard wood (Hollock) Kiln seasoned and chemically pressure treated glazed & skeleton shutters, open rebated at prepared to receive glass/gauze (without sash bars) edges of framing plain, chamfered, or rounded, fitted with and incl cut and mitred beads for securing glass, gauge etc, size of members of shutters as specified in SSR Pt-I, Sec-8, clause 8.24 (a) fixed to chowkhats complete all as specified and directed.

M & L factory made steel windows with side hung shutters including box type hinges with steel handle, steel peg stay, locking arrangement etc complete, one shutter with glazing bars for glass penes and other shutter without glazing bars for wiremesh incl wiremesh & panes, dovetailed or welded including pressed steel frame of size 80X40X1.25mm thick filled with PCC and complete all as specified and shown on drawings drg No CEAA/TD/120 R dated 06 June 2002 sheet no 1/4 to 4/4. Note:-(i) PCC for filling in chowkhats shall be measured and paid saperately. (ii) The cost of iron mongery and fittings as per shown on drgs shall be included in the quoted rate of this item. (iii) Gaurd bar/Grills shall be measured and paid saperately.

S & F factory made for box steel ventilator (with bottom portion fixed with pin headed glass pane and top portion with two top hung shutter one with pin headed glass pane and other with wiremesh including pressed steel frame of size 80 X 40 X 1.25mm thick filled with PCC complete with mild steel stay etc) including all accessaries and making the surface good including painting etc all as specifiedd in Drg No. CEAA/TD/120 R dated 06 Jun 2002 Sheet No. 1/4 to 4/4. Note:-(i) PCC for filling in chowkhats shall be measured and paid saperately. (ii) The cost of iron mongery and fittings as per shown on drgs shall be included in the quoted rate of this item. (iii) Gaurd bar/Grills shall be measured and paid saperately.

S&F framed work such as grills, gratings etc with ends of bar shouldered and/or riveted or forged into spikes, framed guard bars etc and similar work conforming to Fe-290, Gde -E-165 complete all as specified.

S&F factory made for pressed steel frames of size 125 X 60 mm with one or more rebates including necessary fixing lugs hinges, locks strike plate etc(thickness of sheet shall be 1.25mm) and with & including making good the plaster of wall in CM 1:4 and 2 coats of oil bound distamper on new surface over primer etc complete all as specified and as directed.

S&F 25 mm thick flush shutters for cup board factory made solid core construction with block boards core and plywood face panels, commercial type on both sides (ISI marked) fixed to chowkhats complete all as specified and directed.

S & F Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F 18/19 mm thick Particle board, medium density, flat pressed, single layer type or three layer type with BWR type adhesive, fixed with screws to timber frame work in Lofts, and almirah shutters or other placed as specified and directed by Engr-in-charge.

S & F 100 mm long medium weight, stainless steel hinges. complete all as specified and directed.

S & F 100 mm long medium weight, mild steel Butt hinges complete all as specified and directed.

S&F aluminum anodized barrel tower bolt of extruded section size of bolt 150mm complete all as specified and directed.

S&F aluminum handle cast type anodized 150 mm size complete all as specified and directed.

S&F for 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

M & L for applying two coat of synthetic enamel paints over one coat of pink primer on wooden surfaces over 10 cm width or girth including preparation new surfaces complete all as specified and directed.

M&L two coats of synthetic enamel paint to steel surfaces of any description,over 10cm in width or girth, not otherwise described over one coat of red oxide primer including preparation of surfaces complete all as specified and directed.

Supply and fixing stainless steel wire cloth 0.56mm nominal dia of wire and avg width of aperture 1.18mm complete all as specified and directed.

Hacking out old broken glass any thickness size, quality or description from wooden frame glazed with puty or fixed with beads complete all as specified and directed..

Supply and fixing 3mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed.

S & F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, Overall length of cover plate 150 mm complete all as specified and directed.

S&F 150mm long Mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified.

Demolition and breaking up rain water pipe (PVC, AC, or re-inforced concrete ) of sice 100mm coplete all as specified and directed.

S&F PVC SWR pipes 110mm bore single socketed in any length with rubber ging joints fixed to wall complete all as spd and directed.

S&F 110mm bore PVC (SWR) bends any radius all as specified

Dismantling of cast iron pipe of 100 mm bore, set in cement mortar complete all as specified and directed

S&F 100 mm bore cast iron, sand cast soil, waste and vent pipes, in any length with or without ears with cement joints, fixed on wall complete all as specified and directed.

Dismantling of cast iron pipe of 75 mm bore, set in cement mortar complete all as specified and directed.

S&F 75 mm bore cast iron, sand cast soil, waste and vent pipes, in any length with or without ears with cement joints, fixed on wall complete all as specified and directed..

S&F in repair CI bends (T)100mm bore ( any radius ), diminishing pieces or tapers (larger bore measured) of complete all as specified and directed.

S & F in repair CI vent cowl 100mm dia complete all as specified and directed.

M&L in repair Cast Iron floor trap 75mm dia with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed.

S&F Stack clamps out of 50mm by 5mm flat iron & 16mm dia round iron stays. Including bolts & nuts & securing ends of stays to wall or roof for 75 mm bore pipe complete all as specified and directed.

S&F Stack clamps out of 50mm by 5mm flat iron & 16mm dia round iron stays. Including bolts & nuts & securing ends of stays to wall or roof for 100 mm bore pipe complete all as specified and directed.

M&L two coats of oil bound distemper on newely plastered wall surfaces including preparation and 3mm thick wall care putty complete all as specified and directed.

M/L for prepration of newly plastered external surfaces of wall Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces in Berger/Apex in Asian /Nerolac anti fungal emulsion paint of approved brand and shade over one coat of alkali primer all as per manufacturs instructions incl necessary scaffolding incl writing letters etc complete all as specified and directed by Engr-in-charge.

M&L for applying two coats of white wash on old ceiling surface including preparation of surface complete all as specified and directed.

M&L for applying two coats of white wash on old wall surface including preparation of surface complete all as specified and directed.

M & L preparing old decorated surface of walls and applying two coats of oil bound distemper with 1 mm thick wall care putty to make smooth surface incl complete removal of existing treatment on walls all as specified and directed by Engr-in- charge

M/L for prepration old plastered external surfaces of wall Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces in Berger/Apex in Asian /Nerolac anti fungal emulsion paint of approved brand and shade over one coat of alkali primer all as per manufacturs instructions incl necessary scaffolding incl writing letters etc complete all as specified and directed by Engr-in-charge.

M&L for 75mm thick PCC 1:5:10 type E-2 (40 mm graded stone aggregate) as filling of foundation/ WC and finish the surface even and rough .

M&L for 25mm thick PCC 1:2:4 type B-1 (20 mm graded stone aggregate) as flooring and finish the surfaces of concrete top even and fair complete all as specified

Excavation in trenches not exceeding 1.5 metre wide & not exceeding 1.5 metre in depth for foundations, manholes, sewerage pipe lines etc n.exc 10 sqm on plan and getting out in soft / loose soil complete all as specified and as directed by Engineer-in-Charge .

Returning filling in, including spreading, leveling , watering & well ramming in layers not exceeding 25 cm thick each all as specified and as directed by Engineer-in-Charge.

Removing excavated material to a distance not exc 50 m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed

Demolition and breaking up drain pipes SGSW,AC or reinforced concrete pipe up to and incl 150 mm bore pipes all as specified and directed by Engineer-in-Charge.

Material & labour for PCC 1:3:6 type C-2 using 40 mm graded stone aggregate to drain pipes incl packing under & haunching against the sides of pipe 150 mm dia ( internal) after they are laid and tested complete all as

M & L for 150mm dia Reinforced concrete pipes, class NP3, laid and jointed complete with collars complete all as specified and directed.

S&F in repair salt glazed stoneware gully traps of size 150x150 mm, square or round mouthed, type ‘P’ complete all as specified.

Demolition of precast RCC articles built in cement mortar including all quoins, arches, pillars, etc. and removing from site all as specified and directed.

M&L for pre-cast RCC (1:2:4) type B-1 (using 20mm graded stone aggregate) cover slabs for man-holes etc set in CM (1:6) complete all as specified and directed.

M&L TMT bar 10mm dia & over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, footings,slab hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality conforming to GD-I. IS-432 (Part I) complete all as specified and directed.

Demolition of PCC in ground floors & pavings n exc 15 cm thickness (below or above ground level) (unreinforced) complete all as specified and directed.

M&L for 75mm thick Cement concrete type D- 2, 1:4:8 (40mm graded aggregate) complete all as specified and directed.

M & L for preperation of formation bed over 25 mm thick sand cusion and pointed in colour cement mortar 1:3. complete all as specified and directed

M&L for machine made rubber moulded precast coloured interlocking tiles of any shape and size with grey cement and pigment confirming to IS 15658-2006 of 60mm thick M 35 grade laid, jointed complete all as specified

M & L for 25mm thick cement concrete type B1 1:2:4 (20mm graded aggregate) complete all as specified and directed.

S&F of Prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in chajja covering/cladding to wall fixed with self tapping screws including dismantling corrugated steel sheeting complete all as specified and directed by Engr-in-Charge.

S & F Framed work as in doors or gates of angle or other section with gusset plates, rails,braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rails and guides) and hanging; also fastening complete allas specified and directed.

Excavation in trenches n exc 1.50 m wide and n exc 1.5 m in depth for foundation etc in hard dense soil and getting out complete all as specified and directed.

M&L PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete etc.complete all as specified and directed.

Removing excavated soil, exc 50 m but n exc 250 m and deposited where directed at a level n exc 1.50 m above the starting point complete all as specified and directed.

M&L for morrum/red bajri filling under floors or pavings,laid in layers n exc 15 cm thick each , spread,levelled and rammed including watering complete all as specified and directed.

M&L for 100 mm thick PCC (1:4:8) type D-2 using (40 mm graded stone aggregate) as in sub base complete all as specified and directed.

M&L for 40 mm thick PCC (1:2:4) type B-0 using (12.5 mm graded stone aggregate) as in floor finishing cement concrete surface even and fair with out using extra cement complete all as specified and directed.

M&L RCC M-25 (using 20 mm graded stone aggregate) as in footing, foundation and plinth beams etc. complete all as specified and directed.

M&L RCC M-25 (using 20 mm graded stone aggregate) as in columns, pillars, piers, posts and struts complete all as specified and directed.

M&L RCC M-25 (using 20 mm graded stone aggregate) as in beams, cantilevers, bressumers, lintels, over 1.50 m span etc. complete all as specified and directed.

M&L RCC M-25 (using 20 mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors and roof etc and the like complete all as specified and directed.

M&L for Form work to sides of concrete foundations, footings, bases of columns and raft beams, side and soffits of foundation and plinth beams of rough finished surfaces of concrete complete all as specified and directed.

M&L for Formwork to sides of pillars, posts, struts, piers,columns, and stanchions Rough finished surfaces of concrete Square, rectangular or polygonal complete all as specified and directed.

Formwork to sides & soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors & beams, etc. Rough finished surfaces of concrete flat complete all as specified and directed.

Form work to soffits of suspended slabs, such as roof slab, floor slabs, landing and similar work, n.exc 200 mm thick complete all as specified and directed.

M&L for Mild steel TMT bars of 5mm dia and over upto including 10mm dia in stirrups, spacers and binders complete all as specified and directed.

M&L rendering 10 mm thick, in CM (1:6) on fair faces of brick or concrete surfaces of walls, finished even and smooth without using extra cement complete all as specified and directed.

M&L rendering 10 mm thick, in CM (1:3) on concrete surfaces in ceiling, finished even and smooth without using extra cement complete all as specified and directed.

M&L rendering 15 mm thick in CM (1:4) in two layer i.e. first layer 10mm thick and second layer 5mm thick on surface other than fair finish of brickwork/concrete/PCC block masonry wall or on stone masonry wall using water proofing compound @ 3% by wt of cement mixed with in second/finish coat and finished even and smooth without using extra cement ( Note : WPC will be measured & paid seperately) complete all as specified and directed.

M&L two coats of oil bound distemper on newely plastered wall surfaces including preparation and 3mm thick wall care putty complete all as specified and directed.

M&L Preparing new plastered surfaces and applying two coats of cement base paint over a coat of primer on wall surface etc complete complete all as specified and directed.

M&L PCC (1:4:8) type D2 (using 40mm graded stone aggregate) as in sub base, 75 mm thick , finished even and fair without using extra cement complete all as specified and directed.

M&L PCC (1:3:6) type C-2 (using 40mm graded stone aggregate) as in plinth protection, 75mm thick, finished even and fair without using extra cement complete all as specified and directed.

M & L for rendering 10 mm thick in cement mortar 1:3 with WPC @ 3 % by weight of cement on roof surface complete all as specified. NOTE : Water Proofing Compound shall be measured and paid separetely.

M & L for applying roof treatment on top of roof with 3 mm minimum thickness APP modified membrane (weighing 3 Kgs/persqm) with non-woven polyster reinforcement/mat(centre core) with thermal insulation with white mineral finish on upper side of membrane laid by rorch application method with overlap 100 on length and 100 mm on the width side as per manufacture's instructions over a coat of approved cold applied butuminous oil based primer (IS-3384) @ 250gm/sqm complete all as specified and directed by engineer-in-charge.

M & L for Vitrified Ceramic tiles 10 mm thick light shade edded and set in 15 mm thick screed bed (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L for Anti termit treatment for Treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

M&L for Anti termit treatment for Treating of backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface. (Area of the sub structure in contact with backfill to be measured). complete all as specified and directed.

M&L for Anti termit treatment for Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and directed.

M&L for Anti termit treatment for Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

M&L for Anti termit treatment for Treating the soil with external perimeter of building at the rate of 2.25 litre complete all as specified and directed.

S&F 30 mm thick flush shutters factory made solid core construction with block boards core and plywood face panels, commercial type on both sides (ISI marked) fixed to chowkhats complete all as specified and directed.

S&F three track aluminium powder coated sliding window with three sliding shutter , the size of outer frame three track 100 x 37x 1.50mm thick ( using two track for glazed window shutter and one track for wire gauged ) , the section shutter size 37x 18x 1.2mm thick and glazing with 5 mm thick Transparency glass of poly carbone including all-around suitable rubber gasket and stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.4mm and fixed on aluminum flat and inserted in the frame of shutter with tracking arrangement each sliding window shall be provided with one number handle including locking arrangement & 2 numbers’s sliding rollers of nylon with including anodised aluminium grill and all necessary fittings complete all as specified and directed.

M&L for Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

M & L precast cement concrete block masonry type C1, 1:3:6 (using 20 mm graded stone aggregate) with solid block or slab 10 cm thick and setting in mortar 1:4 all as specified.

M&L Reinforced cement concrete type B1 , 1:2:4 (using 20mm graded stone aggregate work in Slabs supported on walls,beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and in shelves and the like complete all as specified and directed.

M & L for 20 mm thick Granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12 mm thick in cement mortar 1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed.

M&L Glazed coloured ceramic tiles in vertical surface 350 x250x 7 mm/ 450x 350x7 mm on vertical surfaces as in skirting/dados etc. Set & jointed in neat cement slurry & pointed in white or coloured cement to match the shade of tiles complete complete all as specified and directed.

S&F 15mm bore Bib taps, chromium plated, cast copper alloy with crutch or butterflyhandle, screwed down,screwed for iron pipe or for bbrass ferrule andfixed complete all as specified & directed.

S&F stainles steel sink made out of stainless steel 1.00mm thick sheet of bowl size 560X400X200mm kitchen with plugs, washers and wastes;including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe excluding taps waste chain plug stopper but incl brackets incl waste pipe cutting pinning in ends of brackets complete all as specified and directed at site.

S&F CP coupling 40mm dia for sink with long screwed end and fly nuts flanged and bedded in red lead cement complete all as specified and directed.

S&F 75mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement to waste pipe fixed in cement concrete type B1(1:2:4) all as specified and directed

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement.

S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

M&L for mirror polished machine cut kota stone slab flooring 20-25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing over and including 20 mm thick screed bed in cement mortar (1:6) complete all as specified and as directed Note:- The size of kota stone slab not less than 550mmx550mm (cut size except the location where balanced.)

S & F in repair Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

Taking down u/s perished point wiring for light /fan /socket /power with all fittings and fixtures, tube lights complete including making good the disturbed surfaces complete all as specified and as directed

M&L for Point wining with 1.5 Sqmm FRLSH, PVC insulated and unsheathed multi stranded FRLS flexible copper conductor cable in and incl rigid PVC conduit concealed with pressed mild steel terminal boxes duly painted with a coat of red oxide primer fixed flushed to the wall with 3mm thick plastic laminated sheet cover of adequate size for one light or one fan controlled by one switch incl 1.5 Sqmm FRLS, PVC insulated and unsheathed multi stranded flexible copper conductor cable as earth wire to common earth dolly, including cutting chases in brick/block/stone masonry wall, replastering and making good to match the existing specifications complete all as specified and directed by Engr-in-charge Note a) Unit rate include for cutting chases for conduits and sunken boxes and making good to wall, floors etc

All as per Item No 147above but for one ceiling fan/exhaust fan point controlled by one switch complete all as specified and directed

All as per Item No 147 above but for one 5 Amps socket point on independent board

All as per Item No 147 above but for one 5 Amps socket point on same board.

M&L for Point wiring with 2.5 sqmm FRLSH, PVC insulated and unsheathed multi stranded flexible copper conductor cable drawn in and including rigid PVC concealed conduit medium grade of suitable size with pressed steel terminal boxes of adequate size fixed flushed to the wall with 3mm thickness plastic laminated sheet cover for one 3 pin socket outlet 15 Amp on independent board including 'continuous 2.5 sqmm FRLS,PVC insulated and unsheathed copper conductor cable (multistranded) as earth wire to common earth dolly, including cutting chases in brick wall replastering and making good to match the existing specificationscomplete all as specified Note a) Unit rate include for cutting chases for conduits and sunken boxes and making good to wall, floors etc

S&f switch 5 Amps piano flush type single pole one way complete all as specified and directed

S&f switch socket combination flush type 5 Amps, 2/3 pin multipurpose complete all as specified and directed

S& F switch socket combination flush type 5/15 Amps 3/3 pin universal multipurpose complete all as specified

S&F ceiling rose surface bakelite 65x50mm three terminal complete all as specified and directed.

S& F lamp holder,PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S& F in replacement LED build of capacity 9 watts complete with all accessories base (ISI Marked) all as specified and directed by Engir-in-charge.

S&F LED tube light fitting 1x20W, 230V, including LED (tube rod), 4 feet batten fitting fixtures, complete with all accessories internally pre-wired and including connecting up with three core twisted flexible copper conductor cable with suitable size complete all as specified and directed.

S&F in Replacement of sub main wiring with two run of single core (FRLSH) PVC insulated and unsheathed cable with copper conductor (multistranded) having nominal area 2.5 Sqmm drawn through conduit concealed type and making electric connections including one run (FRLSH) PVC insulated single core copper conductor cable 2.5 Sqmm as a earth continuity conductor drawn through PVC conduit, including cutting chases in brick wall wherever necessary, replastering and making good to match the existing specifications including taking down old submain wiring complete all as specified and directed by Engineer-in-Charge. Note: (i) Rates are deemed to be included chases of conduit and making holes in wall/floor for passing in or through conduit (ii) Two run of 2.5 sqmm single core (FRLSH) PVC insulated copper conductor cable one run of 2.5 sqmm copper conductor cable (FRLSH) as a earth lead will be measured as a one unit.

S&F in Replacement of sub main wiring with two run of single core (FRLSH) PVC insulated and unsheathed cable with copper conductor (multistranded) having nominal area 4.00 Sqmm drawn through conduit concealed type and making electric connections including one run (FRLSH) PVC insulated single core copper conductor cable 4.00 Sqmm as a earth continuity conductor drawn through PVC conduit, including cutting chases in brick wall wherever necessary, replastering and making goed to match the existing specifications including taking down old submain wiring complete all as specified and directed by Engineer-in-Charge. Note: (i) Rates are deemed to be included chases of conduit and making holes in wall/floor for passing in or through conduit (ii) Two run of 4.00 sqmm single core (FRLSH) PVC insulated copper conductor cable one run of 4.00 sqmm copper conductor cable (FRLSH) as a earth lead will be measured as a one unit.

Taking down unserviceable main switch/DB/MCBs incl disconnecting from mains and making good the disturbed surfaces complete all as specified and directed.

S &F LED street light 20 W IP 66, with aluminium pressure die cast housing, toughened glass in the front with complete with all accessories internally pre-wired complete all as specified and directed

M&L in replacement bracket for street light fitting made out of 25 mm bore pipe light grade Gl tube bent to shape required, fixed with and including MS flat iron clamps, poits, nuts, washers duly painting the bracket with two coats of aluminium paint over a coat of zinc chrome primer complete all as specified and directed.

S&f sheet metal enclosures single pole and neutral 4 way, 240 volts with 200 Amps rated bus bar with double fixed on flush to the wall including making the hole in the wall and fixing the DB including cement works and plastering complete all as specified and directed.

S&f sheet metal enclosures single pole and neutral 8 way, 240 volts with 200 Amps rated bus bar with double fixed on flush to the wall including making the hole in the wall and fixing the DB including cement works and plastering complete all as specified and directed

S&f MCB single pole and neutral, 240 Volts 6 to 40 Amps, 10 KA complete all as specified and directed.

S&f MCB single pole, 240 volts 6 to 30 Amps capacity, 10 KA complete all as specified and directed

M& L for Earthing complete with 600x600x6.3mm thick Gl earth plate electrode buried directly in ground not less than 2.25mtr below GL with the top edge of the plate at a depth not less than 1.5 mtr from GL connected to GI earth lead of 4mm dia by means of nuts, bolts, washers, checknuts etc made out of galvanised iron or steel, earth wire protected by galvanised iron pipe, connected to main switch board complete including necessary earth work excavation, PCC chamber, watering pipe, funnel, wiremesh, RCC chamber cover etc complete ali as specified and directed. in EP No 3 of SSR Part-1.

S&F exhaust fans AC single phase 230/240 V of size 450 mm sweep, 1400 RPM double ball bearings heavy duty motor with louvers etc with mounting accessories like fastener grouting to wall, including electrical connection upto ceiling rose, cutting through stone masonry wall for providing opening suitable for the exhaust fan, finishing the disturbed surface making good with PCC 1:2:4 and cement mortar 1:4 etc complete all as specified and directed.

Supply and laying in repair of GI pipe, Medium Grade ISI marked with all fittings laid in wall complete all as specified and directed for the sizes 15mm bore

Supply and laying in repair of GI pipe, Medium Grade ISI marked with all fittings laid in wall complete all as specified and directed for the sizes 25mm bore

Supply and laying in repair of GI pipe, Medium Grade ISI marked with all fittings laid in wall complete all as specified and directed for the sizes 40mm bore

Supply and laying GI pipe 50mm dia, light grade ISI marked with all fittings laid in trenches, fixing in wall and pole including suitable GI clamps for bracing the pipe with pole for cable protection complete all as specified and directed.

S& F in repair of Gun -metal globe or gate valve with iron wheel head, screwed both ends or iron pipe and for unions and fixing including taking down existing unserviceable valves complete all as specified and directed.

25 mm dia

15 mm dia

Supply, laying and testing cable in repair of LT XLPE insulated, screened, PVC bedded, galvanized steel strip of wire armoured, electric power cables (heavy Duty) 1100 Volts grade with stranded aluminium conductor of size 6sqmm 2 core complete all as specified and directed.

Supply, laying and testing cable in repair of LT XLPE insulated, screened, PVC bedded, galvanized steel strip of wire armoured, electric power cables (heavy Duty) 1100 Volts grade with stranded aluminium conductor of size 10 sqmm 2 core complete all as specified and directed.

M&L for providing tibba sand in trenches as sand cushioning to U/G cable including punning down of sand un layer complete all as specified and directed.

M&L for 40 to 50 mm thick rough dressed jodhpur type stone slab cover 25 to 30cm wide and 40 to 50 cm in length laid dry abutting each other complete all as specified and directed

Cutting of existing road/PCC n. exc 20cm wide and n.exc 30cm in depth for laying protecting pipe line etc and removing the debris n.exc 50cm and filling with PCC 1:2:4 over the protection pipe complete all as specified and directed.

National Rewinding Works

S.K. INFRASTRUCTURE

Aggarwal brothers and company

Devi Engineeing

AMBEY MAA CONSTRUCTION COMPANY

Lalit and Brothers

M/s Sati Jasnath Enterprises