Genguvarpatti Town Panchayat Theni District CGF 2025 2026

Earth work excavation for foundation by manual means for Isolated, Combined and Other type foundations in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2.00mts. and clearing and levelling the site, etc., complete complying with standard specification and as directed by the departmental officers.

First depth of 0 to 2m

Earth work excavation for foundation by manual means for Isolated, Combined and Other type foundations in SDR - (Not Requiring Blasting) Earth work excavating and depositing on bank with initial lead of 10 m & initial lift of 2m in Soft disintegrated rock, laterite, soft rock or kankar, not requiring blasting and clearing and levelling the site, etc., complete complying with standard specification and as directed by the departmental officers.

Second depth of 2 to 3m

Earth work excavation and depositing on bank with initial lead of 10 m and lift of 2 M in narrow trenches having bed width 1.25m & below for laying of pipes for water supply and sewerage works in the following type of soils as directed by Departmental officers - Hard stiff clay, stiff black cotton, hard red earth, shales, murram gravel, stoney earth and earth mixed with small size boulders and hard gravelly soil.SS20B

100 MM Dia DI K9

150 MM Dia DI K9

200 MM Dia DI K9

Supplying and filling in foundation, basement, etc with filling crushed stone sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Cement Concrete 1:5:10 (One Cement, Five crushed stone sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and including curing etc. complete complying with standard specification and as directed by the departmental officers -Mixing by mechanical means

Cement Concrete 1:2:4 (One Cement, Two crushed stone sand and Four hard broken stone jelly) using 20 mm gauge hard broken granite stone jelly for all RCC items of works excluding cost of reinforcement grill and fabricating charges, centering and shuttering but including Super Plasticiser, laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc. shall be finished smooth with Cement Mortar 1:3 (One Cement and Three Sand) and kraft paper laid over it without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers - manual mix

Providing and laying in position, Standardised Concrete Mix M-30 Grade by insitu machine mix concrete adopting weighing batch method in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 400 kg/m3 and maximum water cement ratio of 0.45, including admixture (plasticiser / superplasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 Cu.m) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 Cu.m) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m’) 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

Column footing below 1.50 m from GL

Column below GL upto 1.50 m

0 - 4.50 m Above GL

4.50 m to 7.32 m Above GL:

7.32 m to 10.98 m Above GL

10.98 m to 14.64 m Above GL

14.65 m to 18.30 m Above GL

18.3 m to 21.96 m Above GL

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, Sill slabs etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid with silver oak joists of size 10cm x 5cm & 7.5cm x 5cm as support runner , vertical stiffener, side support and Top Horizontal stiffener spaced at about 60cm to 90cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid). Square Column:

Column 0 to 3.3m ht. above G.L and below GL

Colum above 3.3m to 4.3 ht from GL

Column above 4.30 m upto 5.30 m

Column above 5.30 m upto 6.30 m

Column above 6.30 m upto 7.30 m

Column above 7.30 m upto 8.30 m

Column above 8.30 m upto 9.30 m

Column above 9.30 m upto 10.30 m

Column above 10.30 m upto 11.30 m

Column above 11.30 m upto 12.30 m

Column above 12.30 m upto 13.30 m

Column above 13.30 m upto 14.30 m

Column above 14.30 m upto 15.12 m

Plain Surface

Column footing

For G.L. brace 0-3.3 m

For brace at 3.78 m height

For brace at 7.56 m height

For brace at 11.34 m height

Floor beam sides from 15.12 m to 15.59 m above GL - Inside

Floor slab and working platform at 15.59m above G.L..

Roof slab at 3.55 m above floor slab

Curved Surface

upto 3.30m ht.

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel reinforcement grills of all variety like HYSD/CTD/TMTand all grade like Fe 500, Fe550D, Fe 500 D etc., for all RCC works as per design given including cost of steelreinforcement and G.I. binding wire, wastage etc. complete complying with standard specification and as directed by the departmental officers.(Contractor has to make his own arrangements for the supply of steel reinforcement and binding wire)

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification and as directed by the departmental officers.

Providing RCC inside ladder as per approved design 3.55 m Height

Providing RCC Spiral Staircase as per Approved design

Providing RCC ventilator over roof slab and roof dome of S.R. (0.15 m dia)

Cut Stone Fully Dressed to size on all faces and as directed bydepartmental officers

Providing C I (Hevy duty) manhole cover of size 0.60 x 0.60M and as directed by Departmental officers

Providing RCC hand rails at Roof slab and at landing Slabs of outside Ladder as per drawing

Curved Surface

Inlet ( 100mm CI Pipes/ 20.66 mtr)

Outlet ( 100mm CI Pipes/ 17.55 mtr)

Scour ( 100mm CI Pipes/ 16.95mtr)

Overflow ( 100mm CI Pipes/ 20.20 mtr)

Refilling with excavated soil (other than sand) complying with standard specification for filling in foundation and basement.

Refilling with excavated sand complying with standard specification for filling in foundation and basement

100 MM Dia DI K9

150 MM Dia DI K9

200 MM Dia DI K9

Labour charges for Painting Board Emblem in accordance with the size and specifications as approved by the Board on the Service Reservoirs including cost of all consumables, one coat of base paint,scaffolding charges including painting NRDWP Logo on the Service Reservoirs.

Supply and Delivery DUCTILE IRON SOCKET/SPIGOT PIPES FOR CLASS K9 AS PER IS 8329/2000

100 MM Dia DI K9

150 MM Dia DI K9

200 MM Dia DI K9

Labour for cutting open road for laying water mains or sewer.

B.T. Roads (or) Maccadam road

Supply and Delivery DUCTILE IRON SPECIALS AS PER IS 9523/2000

100mm - 90 Deg D/S Bend

100mm - 22 1/2 Deg D/S Bend

150mm - 90 Deg D/S Bend

150mm - 45 Deg D/S Bend

200mm - 90 Deg D/S Bend

200mm - 45 Deg D/S Bend

200mm - 22 1/2 Deg D/S Bend

Supply, Delivery and fixing of DI D/F Gate valves (Soft Seated) resilient seated soft sealing gate valves (sluice valves) with body bonnet of ductile cast iron of grade GGG40 or equivalent grade, wedge fully rubber lined with EPDM, replaceable spindle nut, without gland packing and with 3 O-Ring protection on the shaft and seals of NBR and the valves should be of vaccum tight and 100% leak proof with face to face dimentions as CI D/F SLUICE VALVE WITH CAP/ WHEEL AS PER IS 14846/2000 PN 1.0 WITH ISI MARKING All the valves should be with electrostatic powder coating both inside and outside with pocket less straight thro' body passage, inside and outside color Blue including Flange/socket and Flange/spicot tail pieces, etc., loading,unloading, Transportation charges and stacking etc. complete as per specifications. All the valves are to be compatible for burried application with pressure rating PN 10/16.

100 mm diameter

Manufacture, Supply and Delivery of Tamper proof C.I. SINGLE AIR VALVE AS PER ISI 14845/2000 with pressure range from PN 1.0 to 2.5 with body and cover made of Ductile Iron of Grade GGG 40 or equivalent grade conforming to IS 1865 with Food Grade Epoxy Powder coating(EP-P) inside and for outside of colour blue RAL 5005. All internal parts such as float, shell etc., cover bolts, made of Austenitic alloy steel of SS AISI 304/316. The float shall be made of Polytetrafluroethylene/ Austenitic alloy steel of AISI 304/316. Gaskets and seals of EPDM / Neoprene rubber and as amended from time to time and suitable for water supply main including loading freight, transit, unloading and stacking them at site etc. complete

50 mm Valve

Supply and Delivery Non-return valves Wafer type (Dual plate check valve) Conforming to IS and 5 years warranty

150mm diameter

Electromagnetic Flow Meter shall be a velocity sensing Electromagnetic type, microprocessor based signal converter, sealed housing, flanged tube meter for 1.0 Mpa working pressure, manufactured to highest standard available for mag-meters, equipped with minimum six digit digital totalizers, reading in different units (Kiloliters / Cubic meter) and shall be accurate within 0.5% of Measured value, shall operate within a range of 0.3 m/sec to 4 m/sec and be constructed as follows: Meter tube (Sensor) shall be fabricated from stainless steel tube and use class PN10 flat face carbon steel flanges in accordance with IS 1538. These flanges shall be welded to the flow tube. The internal and external of the meter tube shall be blasted to near white and lined with hard rubber/ Polyurethrene/ PTFE preferably by SBR or EPDM. Meter tube shall have a constant nominal inside diameter offering no obstruction to the flow.The accuracy should be inclusive of linearity, hysteresis, repeatability, temperature and pressure effects. Coil Housing shall be fabricated from stainless steel (SS304)/ Die cast Aluminium/ Carbon steel with anticorriosive paint for corrosion resistance and welded to the tube providing a completely sealed environment for all coils, electrode connections and wiring harness capable of submerged or buried operation with IP68 Protection. Signal Converter shall be pulsed DC coil excitation type with auto zeroing. The signal converter shall be remotely mounted away from the meter. The converter shall indicate direction of flow and provide a flow rate indication and a total of flow volume for both forward and reverse directions. The converter shall provide an isolated 4-20 mA output into minimum 500-ohm load and a frequency output of a maximum of 0-10 KHZ and a scaled pulse output. The microprocessor based signal converter shall have a self-diagnostic test mode and a backlit display that continuously displays “Rate of Flow” and “Total Volume”.Converter shall be supplied with a programmable low flow drop out, higher flow and empty pipe zero return. The signal converter housing should be die-cast aluminum with glass window. The converter cum transmitter should be fully programmable from the front facia. The programming should be user friendly, self-prompting menu driven. Flow meter test calibration certificate from FCRI, flow test lab / NABL accredited lab to be furnished.

150mm diameter

Lowering of DI pipes and specials carefully into the trench and laying to proper grade and alignment including labour charges, incidental and operational charges etc complete as per standard specifications and as directed by the Departmental Engineer.

100 MM Dia DI K9

150 MM Dia DI K9

200 MM Dia DI K9

Cutting of CI and DI pipes and specials true to axis and filing smoothly and finishing the ends complete, with / without water in the pipe including labour charges, incidental and operational charges etc complete as per standard specifications and as directed by Departmental Engineer.

100 MM Dia DI K9

150 MM Dia DI K9

200 MM Dia DI K9

Jointing C.I/ D.I-S/S pipes and specials with rubber gaskets (tyton joint) including cost of lubricants. (including cost of jointing materials)

100 MM Dia DI K9

150 MM Dia DI K9

200 MM Dia DI K9

Testing of M.S. / C.I. / D.I / P.V.C. /D.W,C, pipes with hydraulic testing equipment by filling with water (including cost of water @ Rs. 60/KL) and testing to recommended pressure in convenient stretches and attending the bursts if any occured during the test, excluding the cost of pipes but including other incidential and operational charges etc.,complete for the following diameters of pipes.

100 MM Dia DI K9

150 MM Dia DI K9

200 MM Dia DI K9

Barricading work (Where the lines are in narrow width of municipality area, busy streets like Market, Bus-stand and in the Highways etc.) for laying of pipe line using casurina poles at 1.50m center to center (8cm to 10cm dia. and 1.80m height) vertical with horizontal poles in two rows, painting the vertical poles in the road facing sides with ready mix paint, tying the vertical and horizontal poles with coir rope including supplying, delivery and fixing of GI sheet (0.90m x 0.8mm thick) in the horizontal poles and fixing 75mm dia. reflectors including earth work excavation for fixing vertical posts and finally removing and stacking the materials safely for further use etc., complete and as directed by Department Engineer.

SR OHT Outlet

50 mm Valve (Air Valve)

Supply and delivery of Open well Submersible pump set conforming to IS 14220 /2002 and as amended thereafter and BEE 3 Star Rated capable of discharging the following duties due to all causes. The pump shall be with stainless steel shaft and dynamically balanced bronze mixed type impeller, CI FG 200 grade casing and brass screws and rotor shall be of copper rod as per IS 613/1984 with ISI mark. The pump suitable for installation in sump with 1.1KV grade 3 core suitable copper flat submersible cable to a length of 15m with necessary cable joints. The non-return valve located at the top of the pump in the discharge outlet connection is to be designed with minimum friction. The pump should be directly coupled to 2880 RPM, three phase, 50 Hz (±5), 415V+6% & 415V-15% squirrel cage induction motor suitable for DOL upto 5 HP, Fully Automatic Air break Star Delta up to 20 HP and Auto Transformer starter for above 20 HP starting and for continuous operation.

800 lpm against a total head of 80m

15HP or Suitable

Supply, delivery, erection, testing and commissioning of following sizes of power shunt capacitor for power factor improvement, suitable to operate on 415V, 3Ph,50Hz A/C supply, on suitable angle iron frame-works at a height of 0.5m from the ground, including earthing and incidental civil works etc., complete.

Supplying and fixing of following capacity Triple Pole fuse carrier in MS Sheet steel encloure with provision for accommodating the TNEB meter including earthing etc., complete as per TANGEDCO which includes LT meter panel board

Supplying and fixing of following capacity Triple Pole SFU with fuses on suitable angle iron frame with earth connection only.

Supplying and laying following LTUG cables in a trench to be excavated at a depth of 2 ½ ' putting 6” layer of sand and covering the cable with brick and sand refilling the earth to make good as directed or in trench using cable trays with necessary support.

DO - 3 ½ core 50 sq.mm. for Income - (1 Runs for EB/Panel & 1 run for APFC)

DO - 4 core 10 sq.mm - Panel to Starter

DO - 3 core 10 sq.mm - Starter to Motor

DO - 4 core 4 sq.mm. for Aux.supply

Supplying and fixing of cable gland and termination with Aluminium cable lugs for following PVC UG cable and with earth connection

DO - 3 ½ core 50 sq.mm.

DO - 3.5 core 10 sq.mm

DO - 3 core 10 sq.mm

DO - 4 core 4 sq.mm

Supply, delivery and erection of Three Phase 4 way 32 Amps, 10kA LDB with the following: 1 No of 40 A FP isolator for incoming supply 3 Nos. of 16A, DP RCCB 3 Nos. of 16A, SP MCB 1 No of 16A, DP MCB 3 Nos of 6A, DP MCB in sheet steel enclosure fitted with busbars and neutral links and suitable angle iron frame works with provision for earthing etc. complete.

Run of 2 of 2.5 sq mm PVC unsheathed copper single core cable in PVC pipe for mains with continuous earth connection by 14 SWG wire From the MCB DB to the Switch boards in office, store,and 16A power socket.

Wiring with 2.5 sq mm PVC insulated single core copper cables of 650 V Grade on suitable rigid PVC pipe on wall and ceiling with PVC accessories, with MS switch box covered with 3 mm thick hylam sheet with continous earth wire connection of 14 SWG TC wire.

Supply and installation of 240 V - 1 x 18 W LED TL fitting box type with enamelled reflector complete with all accessories - choke, starter, tube, etc. suitable for wall mounting or roof mounting on conduit tube.

Earthing as per ISI specifications with necessary masonary work.

Supply, conveying and fixing CI specials as per the latest revision of IS 1538 including with ISI markings on it including earthwork excavation, lowering into the trenches, aligning, refilling the trenches with excavated soil, watering and ramming to consolidation, etc

200 x 200 mm Flange Equal tee

200 x 250 mm Tapper

200mm 90 deg Bend

200 mm dia CI blank flange

Labour charges for the erection of submersible pumpset in borewell/openwell including fixing and jointing submersible cable with proper clamps upto the starter to required depth and also fixing of riser pipes to the required depth valves erection clamps, pressure gauges upto the exterior wall of pump room and erection of panel board consisting of TPICN switches starter, Voltmeter, Ammeter, three pilot (indicating) lamps capacitor single phasing preventor, water level guard and laying and jointing the cables and twin earthing as per IE rules etc., complete and testing the pumpset and trail run for 10 days.

5HP to 10HP