REPAIRS TO WOODEN FURNITURE FOR MARRIED AND OTM ACCN AT FORT WILLIAM UNDER GE (FW) KOLKATA

BED HARD (MAP) [DRG NO : FD/E6/MAP/08(R)]

Recaning of different type of chair and furniture [Drg No: FD-15, 228, 279, 280, 150, 252, 27, 76(M) & FD-2] Removing of old/worn out cane plastic and recanning with 2mm wide half round cane plastic white of superior quality for seat and back (as applicable) and 3mm wide half round cane plastic on the borders locked in at 125mm intervals complete all as per drawing/directed by Engr-in-Charge :-

All as per item No 1.01 but for foot board .

Welding to existing broken/cracked joints of bed hard and grinding for even and smooth gas welding complete all as specified and directed. (Note : Welding of broken/cracked joints shall be counted one point for one joint).

S&F 8mm dia bolts and nuts and tightening the steel framing structure of bed hard as in repair as per drg and specification complete all as specified and directed. (Note: Each bolts and nuts shall be measured as one unit)

M&L removal of old paint from surfaces of steel framing structure and applying two coats of Synthetic Enamel black paint (first quality) over a coat of red oxide zinc chrome primer , to all sides of steel framing structure of bed hard complete all as specified and directed.

Removing of old unserviceable hard rubber shoe from leg and S&F with new one as per existing of approved quality complete all as specified and directed.

Removing of old unserviceable hard rubber cap from leg and S&F with new one as per existing of approved quality complete all as specified and directed.

Removing of old unserviceable head board of bed hard and S&F new one 18mm thick Pre-laminated MDF board with ISI mark (ISI-2406) both side teak shade , exterior grade with 4 mm teak wood beading and to be fixed with screw as per drawing and specification complete all as specified and directed.

Charpoy MS with MNF Set [Drg No : CWE/C/F/04 and FD/MAP-II/01]

Removing of old worn out/unserviceable ply top of charpoy MS and S&F 12mm thick (7 ply) BWR gde type BB plywood securing with 8mm dia round head countersunk bolts and nuts with washer as per existing shape and size complete all as specified and directed.

Welding to broken joints of charpoy MS and grinding for even and smooth gas welding complete all as specified and as directed. (Note : Welding of each broken joints shall be counted as one point)

M&L for preparing old steel or iron surface of any description over 10cm width or girth and applying two coats of Synthetic Enamel paint (First quality) Black paint before fixing the ply hard top complete all as specified and directed.

Removing of old unserviceable hard rubber shoe from leg and S&F with new one as per existing of approved quality complete all as specified and directed.

Hat Stand with Mirror [Drg No : FD-233/361/362]

Removing of old damaged mirror and S&F new mirror of 5 mm thick mirror as per drg or as directed by Engr-In-Charge.

Removing of old damaged back side ply and S&F new back side ply 6 mm thick BWR quality as per drg or as directed by Engr-In-Charge.

Removing old damaged front ply and S&F new front ply 4mm thick BWR quality one side teak face as per drg or as directed by Engr-in-Charge.

Removing of old damaged hooks and S&F new brass hook to Hat stand and all as per drg or as directed by Engr-In-Charge.

Removing of old unserviceable top ply from bed hard and S&F 12mm thick ply wood (7 ply) commercial of BWR grade, securing with drilling two holes of each stiffener 8mm dia round head countersunk bolts and nuts with washer (06 Nos) as per existing shape and size complete all as specified.

Peg Table [Drawing No : FD-277, 384] Removing following unserviceable components from Peg Table and S&F new components as per the following and fixing the same without disturbing the other parts complete wherever shown on drawing and making functional the furniture as per drg and specification :-

M&L removal of unserviceable top of peg table in any position and S&F new table top made of 18mm thick MDF exterior grade, lamination (teak shade) with teak wood beading extended upto minimum 50mm from the bottom edge fixed in position all as specified and directed by Engr-in-Charge.

Leg made out of 1st class hard wood (teak)

Top rail (shorter) made out of 1st class hard wood (teak)

Top rail (longer) made out of 1st class hard wood (teak)

PVC hard rubber shoe of approved quality

Removing broken/unserviceable hanging clip and S&F new MS Hanging Clips as per suitable size and fix with screw rest all specified by Engr-in-charge.

TABLE CENTRE [Drg No: FD-29M, FD-235 & FD-274] Removing following unserviceable components from Table Centre and S&F new components as per the following and fixing the same without disturbing the other parts including polishing complete wherever shown on drawing and making functional the furniture as per drg and specification.

M&L removal of unserviceable top of table centre in any position and S&F new table top made of 18mm thick MDF board exterior grade, lamination (teak Shade) with teak wood beading extended upto minimum 50mm from the bottom edge fixed in position all as specified and directed by Engr-in-Charge.

Leg made out of 1st class hard teak wood

Top rail (shorter) made out of 1st class hard teak wood

Top rail (longer) made out of 1st class hard teak wood

S & F Ist class Teak wood bracket as per suitable size triangular( 08 Nos in a table) fixed with screws. Complete all as specified.

PVC hard rubber shoe of approved quality

Bed Hard Plywood Top with MNF Set [Drg No : FD-21(M), FD-246]

S&F Top of bed plywood made out of 12mm thick, 7 ply, grade BWR, type BB commercial ply (IS-303) including taking down old one complete all as specified and as directed. Make Archidply/Century Ply/ Green Ply

S&F Head Board with legs made of teak wood covered with 4mm thick plywood 3 ply BWR grade, type BB, with decorative face veneers on one face or as per drawing.

S&F Foot Board with legs made of teak wood covered with 4mm thick plywood 3 ply grade BWR, type BB, with decorative face veneers on one face including taking down old one complete all as per drawing

S&F new teak ply of head board front and back of Bed hard including taking down old one complete all as per drawing

S&F new teak ply of foot board front and back of Bed hard including taking down old one complete all as per drawing

S&F Long rail made out of Ist Class hard wood (Teak wood) including taking down old one complete all as per drawing

S&F Stiffener made out of Ist Class hard wood (Teak wood) including taking down old one complete all as per drawing.

S&F new L shape MS clamp as per suitable size rest all as specified and directed by Engr-in-charge.

Charpoy GI pipe with ply top [Drg No : FD-220R/ CZ/TD/556]

Removing of old unserviceable ply top of charpoy GI pipe and S&F 12mm thick 7 ply BWR gde type BB securing with 6mm dia round head countersunk bolts and nuts with washer (08 Nos) as per existing shape and size complete all as specified and as directed.

S&F Long Rail made of 32 mm bore (medium grade) galvanised iron pipe of Charpoy GI pipe complete

Labour only Short rail, made of 32 mm bore galvanised iron pipe (medium grade) of Charpoy GI pipe (retrieved against item No. 7.02 above) complete

S & F Ist class Teak wood bracket as per suitable size triangular( 08 Nos in a table) fixed with screws. complete all as specified.

S&F 32 mm bore galvanised iron three-way elbow (ISI marked) of Charpoy GI incl taking down existing elbow complete

S&F 32 mm bore galvanised iron check nut of Charpoy GI pipe incl taking down existing check nut complete.

Labour only Legs, made of 32 mm bore galvanised iron pipe (medium grade) of Charpoy GI (retrieved against item No. 7.03 above), with and including 3 mm thick mild steel square plate, welded to bottom of legs, projecting 5 mm peripherally outer dia of leg and provision clamps for MNF set, as per drawing and specification complete

Removing old unserviceable / broken stiffener through grindig or cutting and S&F new 20mm GI pipe and welded the same properly with long rail.

Chair Writing [Drg No : FD-280, 250, 20(M] Removing following unserviceable components from chair writing and supply and fix new components as per the following and fixing the same without disturbing the other parts complete wherever shown on drawing and making functional the furniture as per drg and specification :-

Front leg made out of 1st class hard wood (teak)

Rear leg made out of 1st class hard wood (teak)

Side rail made out of 1st class hard wood (teak)

Rear rail made out of 1st class hard wood (teak)

Front Rail made out of 1st class hard wood (teak)

Arms made out of 1st class hard wood (teak)

Stiffener made out of 1st class hard wood (teak)

Back rest made out of 1st class hard wood (teak)

PVC hard rubber shoe of approved quality

Chair Dining FD [Drg No : FD-279/1105, 250, 20(M)] Removing following unserviceable components from chair dining and supply and fix new components as per the following and fixing the same without disturbing the other parts complete wherever shown on drawing and making functional the furniture as per drg and specification :-

Rear leg made out of 1st class hard wood (teak)

Front leg made out of 1st class hard wood (teak)

Side rail made out of 1st class hard wood (teak)

Front Rail made out of 1st class hard wood (teak)

Rear rail made out of 1st class hard wood (teak)

Back rest made out of 1st class hard wood (teak)

Stiffener made out of 1st class hard wood (teak)

PVC hard rubber shoe of approved quality

Welding to broken stiffener of charpoy GI and pipe grinded for even and smooth gas welding after proper tightening the complete frame complete all as specified and as directed. (Note : Welding of each broken joints shall be counted as one point.)

Front leg made out of 1st class hard wood (teak)

Rear leg made out of 1st class hard wood (teak)

Front/back rail made out of 1st class hard wood (teak)

Side rail made out of 1st class hard wood (teak)

Arms made out of 1st class hard wood (teak)

Rail of seat frame made out of 1st class hard wood (teak)

Rail of back rest frame made out of 1st class hard wood (teak)

PVC hard rubber shoe of approved quality

Teapoy FD [Drg No : FD-278, 232, 34(M, 382] Removing following unserviceable components from Teapoy and supply and fix new components as per the following and fixing the same without disturbing the other parts complete wherever shown on drawing and making functional the furniture as per drg and specification :

M&L removal of unserviceable top of teapoy in any position and S&F new table top made of 18mm thick MDF exterior grade, lamination (teak shade) extended upto minimum 50mm from the bottom edge fixed in position all as specified and directed by Engr-in-Charge.

Leg made out of 1st class hard wood (teak)

Top rail (shorter) made out of 1st class hard wood (teak)

Top rail (longer) made out of 1st class hard wood (teak)

S & F Ist class Teak wood bracket as per suitable size triangular( 08 Nos in a table) fixed with screws. Complete all as specified.

PVC hard rubber shoe of approved quality

Table Writing [Drawing No : FD-27, 249, 33M, 275] Removing following unserviceable components from Table writing and supply and fix new components as per the following and fixing the same without disturbing the other parts complete wherever shown on drawing and making functional the furniture as per drg and specification :-

long rail made out of 1st class hard wood (teak)

short rail made out of 1st class hard wood (teak)

Leg made out of 1st class hard wood (teak)

complete Box of the table including shelf, left /right side, back ply made out of 18mm thick MDF exterior grade, lamination (teak shade)

Chair Easy [Drg No : FD-17 (M), 229, 1108] Removing following unserviceable components from chair easy and supply and fix new components as per the following and fixing the same without disturbing the other parts complete wherever shown on drawing and making functional the furniture as per drg and specification :-

Box back ply 6mm thick 3 ply commercial plywood conforming to IS-303 type BB duly polished

Front shutter made out of 18mm thick MDF exterior grade, lamination (teak shade) duly polished.

M&L removal of unserviceable top of table writing in any position and S&F new table top made of 18mm thick MDF exterior grade, lamination (teak shade) extended upto minimum 50mm from the bottom edge fixed in position all as specified and directed by Engr-in-Charge.

Drawer made of teak wood with 6mm thick 3 ply commercial plywood conforming to IS 303 type BB shall be provided bottom of drawer duly polished

steel Knob round (as per sample) recessed 38mm dia fixed with 20mm screw.

Table 1200x900x760mm [Drg No : FD-224, 283, / FD/MAP-II/03] Removing following unserviceable components from Table 1200x900x760mm and S&F new components as per the following and fixing the same without disturbing the other parts complete wherever shown on drawing and making functional the furniture as per drg and specification :-

M&L removal of unserviceable top of table 1200x900x760mm in any position and S&F new table top made of 18mm thick MDF exterior grade, lamination (teak shade) with teak wood beading extended upto minimum 50mm from the bottom edge fixed in position all as specified and directed by Engr-in-Charge.

Legs made out of 1st class hard wood (teak)

Long side rail made out of 1st class hard wood (teak)

Short Side rail made out of 1st class hard wood (teak)

S & F Ist class Teak wood bracket as per suitable size triangular( 08 Nos in a table) fixed with screws. Complete all as specified.

PVC hard rubber shoe of approved quality

Stiffener made out of 1st class hard wood (teak)

M&L removal of unserviceable top of table in any position and S&F new table top made of 18mm thick MDF exterior grade, lamination (teak shade) with teak wood beading extended upto minimum 50mm from the bottom edge fixed in position all as specified and directed by Engr-in-Charge.

Leg made out of 1st class hard wood (teak)

Long side rail made out of 1st class hard wood (teak)

Short side rail made out of 1st class hard wood (teak)

Drawer made of teak wood and 6mm thick 3 ply commercial plywood conforming to IS 303 type BB shall be provided bottom of drawer duly Frenck polished.

steel Knob round (as per sample) recessed 38mm dia fixed with 20mm screw.

S & F Ist class Teak wood bracket as per suitable size triangular( 08 Nos in a table) fixed with screws. Complete all as specified.

PVC hard rubber shoe of approved quality

Table 900x900x760mm [Drg No : FD-224, 283] Removing following unserviceable components from Table 900x900x760mm and S&F new compone

M&L removal of unserviceable top of table in any position and S&F new table top made of 18mm thick MDF exterior grade, lamination (teak shade) with teak wood beading extended upto minimum 50mm from the bottom edge fixed in position all as specified and directed by Engr-in-Charge.

Legs made out of 1st class hard wood (teak)

Side rail made out of 1st class hard wood (teak)

S & F Ist class Teak wood bracket as per suitable size triangular( 08 Nos in a table) fixed with screws. Complete all as specified.

PVC hard rubber shoe of approved quality

nts as per the following and fixing the same without disturbing the other parts complete wherever shown on drawing and making functional the furniture as per drg and specification :-

M&L removal of unserviceable top of table dining 6 persons in any position and S&F new table top made of 18mm thick MDF exterior grade, lamination (teak shade) with teak wood beading extended upto minimum 50mm from the bottom edge fixed in position all as specified and directed by Engr-in-Charge.

Leg made out of 1st class hard wood (teak)

Long side rail made out of 1st class hard wood (teak)

Short side rail made out of 1st class hard wood (teak)

S & F Ist class Teak wood bracket as per suitable size triangular( 08 Nos in a table) fixed with screws. Complete all as specified.

PVC hard rubber shoe of approved quality

Table 900x600x760mm with/without drawer [Drg No : FD-41, 42, 241, 223, 224, 283, 284] Removing following unserviceable components from Table 900x600x760mm with/without drawer and S&F new components as per the following and fixing in position all as specified and directed by Engr-in-Charge.

M&L removal of unserviceable top of table dining 8 persons in any position and S&F new table top made of 18mm thick MDF exterior grade, lamination (teak shade) with teak wood beading extended upto minimum 50mm from the bottom edge fixed in position all as specified and directed by Engr-in-Charge.

Leg made out of 1st class hard wood (teak)

Long side rail made out of 1st class hard wood (teak)

Short side rail made out of 1st class hard wood (teak)

S & F Ist class Teak wood bracket as per suitable size triangular( 08 Nos in a table) fixed with screws. Complete all as specified.

PVC hard rubber shoe of approved quality

TABLE DRESSING LADIES WITH MIRROR [Drawing No: FD-378 & FD/MAP-II/07] Removing following unserviceable components from Table Dressing Ladies and S&F new components as per the following and fixing the same without disturbing the other parts complete wherever shown on drawing and making functional the furniture as per drg and specification:-

Drawers

Top made out of 18 mm thick Prelaminated MDF Board with teak wood beading

Bottom made out of 12 mm thick teak ply one side

Side frame of 18 mm thick MDF Board and back base of ply 6 mm teak face

Removing of old paint of chair verandha by using paint remover, emery papers etc, and providing two coats of synthetic enamel paint (First quality) as approved coloured on chair frame complete all as per drawing /directed by Engineer-in-Charge.

Mirror of 5 mm thickness

Table dining 6 Persons [Drg No : FD-239, 273, FD/MAP-II/03] Removing following unserviceable components from Table Dining 6 Persons and S&F new components as per the following and fixing the same without disturbing the other parts complete wherever shown on drawing and making functional the furniture as per drg and specification :-

Steel Knob round (as per sample) recessed 38mm dia fixed with 20mm screw.

Table dining 8 Persons [Drg No : FD-239, 273, FD/MAP-II/03] Removing following unserviceable components from Table Dining 8 Persons and S&F new components as per the following and fixing the same without disturbing the other parts complete wherever shown on drawing and making functional the furniture as per drg and specification.

All as per item No 19.01 but replacement of bottom with S&F new 18 mm thick pre laminated MDF Board, exterior grade.

All as per item No 19.01 but replacement of mirror of size 380 x 760 x 5.5mm thick with teak wood frame complete all as shown on drawing.

S&F in replacement of chromium plate knob 25 mm dia of best quality and as approved by Engr-in-Charge.

Removing of old unserviceable top ply from bed hard and S&F 12mm thick ply wood (7 ply) commercial of BWR grade, securing with drilling two holes of each stiffener 8mm dia round head countersunk bolts and nuts with washer (06 Nos) as per existing shape and size complete all as specified.

TABLE DRESSING GENTS WITH MIRROR (FD-230) Removing following unserviceable components from Table Dressing gents and S&F new components as per the following and fixing the same without disturbing the other parts complete wherever shown on drawing and making functional the furniture as per drg and specification:-

Top with 18mm thick pre-laminated MDF board exterior grade one side natural teak faced including teak wood beading on the top.

Side with 18mm thick pre-laminated MDF board exterior grade one side natural teak faced including teak wood beading around the side

Partition shelf made of 18mm thick pre-laminated MDF board

New top of MDF Board 18mm thick and with Ist class seasoned teak wood beading 4mm thick all around including polishing to beading made to shape all as shown on drawing. Specified and directed by the Engr-in-Charge.

S&F in replacement of side with new side of 18 mm thick pre laminated MDF Board, exterior grade and including 4mm thick teak wood beading all-rounded.

Hat Stand with Mirror [Drg No : FD-233/361/362]

Bed ply wood top [Drg No: FD-21(M) , FD-246]

Peg Table [Drawing No : FD-25, 227, 277, 236 & 384]

Table centre [Drg No: FD-29M, FD-235 & FD-274]

Table writing [Drg No: FD-33(M) & 275]

Table dressing ladies with mirror [Drawing No: FD-378 & FD/MAP-II/07]

Table dressing gents with mirror [Drawing No FD-230]

Table bed side FD-276

Table 1200 x 900 x 760mm Drg No -291, FD/MAP-II/03

Table 900x900x760 mm wooden [Drg No : FD-88(M) & DB-3955]

Table 900x600x760mm with/without drawer [Drg No : FD-55(M),42(M) & 284]

Teapoy [Drg No : FD-34(M), DB-3975, FD-234 & FD-278, FD-382]

Table dining 8 persons [Drg No :FD-30(M), 239 &273, FD/MAP-II/03]

Table dining 6 Persons [Drg No: FD-30(M), 239 & 273, FD/MAP-II/03]

Chair Dining [Drg No: FD-16(M), 228 & 279, 1105]

Chair Easy [Drg No: FD-FD-17(M) & 229]

Chair Writing [Drg No: FD-20(M), 250 & 280]

Book case FD wooden

Recaning of Verandha Chair [Drg No FD-199M), 156(M) & 256]

Removing of old/worn out cane plastic of chair verandha recanning with new 4mm wide half round cane plastic white in colour (non recycled) made of superior quality plastic rest all as per drawing /directed by Engineer-in-Charge.

Repairs to broken mild steel components of chair verandah with gas welding, including replacing broken /worn out legs with new 20mm dia MS pipe1.6mm thick 75mm to 100 mm long

S&F PVC rubber shoe/Toe of best quality after removing the old unserviceable shoe all as specified and directed.

Removal of existing polish from wooden surfaces of under mentioned articles of wooden furniture, cleaning the same using sand paper, smoothing properly without leaving any untouched wooden surfaces and polishing the same with two or more coats of French polish of appropriate shade, as approved / directed by the Engineer-in-Charge :-

TABLE BED SIDE [Drg No: FD-276 & FD-265] Removing following unserviceable components from Table Bedside and S&F new components as per the following and fixing the same without disturbing the other parts and making functional the furniture as per drawing and specification :-

Chair Dining

Chair Easy

Chair writing