REPAIR/RESURFACING OF BITUMINOUS ROADS AND ROAD FURNITURE AT DOMESTIC AND TECH AREA OF BRD AND MES COLONY UNDER GE (AF) TUGHLAKABAD

Amount

M&L for Repairs to pot holes any depth, n.exc 1 sqm each including sweeping free from dust and mud or water, scoring sunken surfaces in road, path etc cutting around edges to making good by filling in screened and graded road materials over a priming / tack coat with good by applying tack coat @ 5 kg per 10 sq m, putting in premixed bituminous macadam, well rammed and sealed with binder 9.8 kg per 10 sq m, blinded with 0.09 cu m of stone chippings, 6.3 mm size and again well rammed (including supply of premixed macadam, binder and chippings). depth of potholes exc 30 mm complete all as specified and directed.

Preparing black top surfaces by brushing with wire brushes for removing caked mud etc, sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt etc complete all as specified and directed.

M&L applying priming / tack coat with paving bituminous primer @ 5 Kg per 10 Sqm over old black top surfaces complete all as specified and directed.

M&L for bituminous premix asphaltic semi dense concrete, 30 mm (consolidated thickness) with 5.5% paving bitumen binder of VG 30, by weight of total mix, rolled and compacted to required camber and gradient with 8 to 12 tone capacity power roller to a uniform smooth surface as specified and as directed. Note: The actual requirement of binder shall be as per the job mix design and the tests specified. However quantity of bitumen from the mix design found more than specified 5.5% same shall be provided with no extra cost to the Govt. In case binder content found to be less than 5.5% as per mix design as specified in Schedule "A" shall be adjusted @ the rate of 65.00 (Rs sixty Five ) / kg for the less quantity of bitumen used. The quantity of 5.5% mentioned is exclusive of any wastage and no wastage shall be taken into account for the purpose of above adjustment)

M&L for Premix Bituminous macadam, (consolidated thickness not more than 75 mm) with 4% paving bitumen binder of VG 30, by weight of total mix, rolled and compacted to required camber and gradient with power roller to a uniform smooth surface as specified and as directed.

Preparation of road surfaces and applying thermoplastic reflective paint in marking of minimum 2.00 mm thick single coat as in centre line and edge line road marking of 150/100 mm width using 'HOT MARK' thermoplastic paint (Hot application) white/yellow by indigenous modern prpolled road marking machine as directed including all ingredients such as blinder, glass beads Titanium dioxide calcium carbonate inter fillers themoplastic reuirement for glass shall be the table No 800.4 of MORT specification including spraying of glass beads etc all as per manufacture instructions complete all as specified and directed.

S&F in repair solar road stud as per manufacturer's specifications complete all as specified and directed by Engineer -in - charge Note:-(i) Appropriate epoxy adhesive on the road surface shall be provided as per manufacturers specifiaction before fixing the cat eye and the same is includued in quoted rate by the contractor complete all as specified and directed.

S&F in repair delinator, at the top portion two high performance 100 mm dia reflectors and two rectangular reflectors of 70 mm x 30mm are fixed on both sides of guide post. The body of guide post is moulded in ABS plastic and it is fixed on power coated steel pipe of 1.00 mtr height fixed in ground with PCC 1:3:6 type C-2 of size 300 x 300 x 300mm including necessary excavation and earth work complete all as specified & directed complete all as specified and directed.

S&F in repair solar delinators mounted over or including 50 mm dia MS pipe of length 750mm, coated with black epoxy poweder coating. Four ultra bright flashing LEDs in red or yellow colour, including fixing in ground by excavating post hole of size 300 mm x 300 mm x 300 mm in filling the same with PCC 1:3:6 complete all as specified.

S&F in repair road safety convex mirror made up of polycarbonate reflective and body made of ABS / Fibber / Plastic of size 80 cm dia fixed over & including 40 mm bore MS pipe of 2.4 Metre length duly powder coated embedded in PCC 1:2:4 of size 45 cm x 45 cm x 45 cm and excavation earth work complete all as specified and as directed.

S&F in repair road safety convex mirror made up of polycarbonate reflective and body made of ABS / Fibber / Plastic of size 100 cm dia fixed over & including 40 mm bore MS pipe of 2.4 Metre length duly powder coated embedded in PCC 1:2:4 of size 45 cm x 45 cm x 45 cm and excavation earth work complete all as specified and as directed.

S&F in repair Modular type speed braker / Rumbler made of sturdy plastic (ABS) material of size 250 x 350 x 50mm fixed in position as per manufacturer instruction.

Exavating in post holes (or similar holes) in soft/loose soil each not exceeding 0.5 cum getting out, returning filling in and ramming earth in layers not exceeding 25 cm watering and removing surplus spoil to a distance not exceeding 50 m and making good surface all as specified and directed.

M&L cement concrete (1:3:6) type C-2 using 40 mm graded crushed stone aggregate as in foudation filling and moss concrete complete all as specified and directed.

S&F in repair stainless steel pipe GRDE 304 framed work such as of pipes angles tees, flat incl gusset plates etc and welding and or riverting and similar work complete all as specified and directed.

S&F in reapir 3 mm thick ACP sheet of any colour/shade as approved and one side covered with 3 M retro-reflective sheet & pasting computerized size of letter of retro reflective sheet not exc 30 cm in height including stop commas, short line dashes, hypens brackets etc as directed and pasted with approved adhesive as in sign bound cut to size and fixed to stainless steel frame including all necessary fitting arrangement complete all as specified and dirceted. Note:- Nothing extra shall be paid for writing.

M&L for cleaning, washing and applying two coat of indigo floor coat emulsion paint on old chequured tiles/interlocking tile surface of any description over 10 cm girth or width complete all as specifiec and directed.

Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for 100 mm thick PCC (1:4:8) type D2 using 40 mm graded crushed stone aggregate as in PCC hard standing, complete all as specified and directed.

S&F Machine pressed PCC pre-painted interlocking paver block confirming to IS 15658-2006 of size 60mm thickness M-35 Grade with grey cement and pigment laid dry, including dismantalling tiles of any thickness laid dry complete all as specified.

M&L for sand filling under sub base including watering and consolidating as in cushioning bed for interlocking paver block complete all as specified and directed.

M&L 75 mm thick cement concrete (1:2:4) type B2, using 40mm graded crushed stone aggregate as in sub-floors, sub-bases, etc. complete all as specified and directed.

Material & labour for 10 to 12 mm thick vitrified unglazed and unpolished, scratch resistant, matt finished coloured tiles (square/rectangular) of size not less than 300mm x 300mm as in parking /hardstanding etc including set, jointed in cement slurry and pointed in white or coloured cement to match the colour/ shades of tiles over and including 20 mm thick screed bed in CM (1:6) and removing rubbish off the premises from Defence land complete all specified and directed .

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete including demolishion of kerb stone complete all specified and directed.

M&L in repair for polyster zebra pattern vention blind of size and color as approved by GE having thickness not less than 1.5mm including all fixing arrangement and fixtures required for full functioning of blind complete all as specified and directed. Make:- Deco window, Vista, Design are decoror as approved by GE.

M&L for applying two coat of approved synthetic enamel paint (ISI Marked) over one coat of redoxide primer on new/old steel surface including perparation with sand paper complete all as sepcified and directed.

Schedule of Credit

M/S AKASH CONSTRUCTION COMPANY

YOGESH ENTERPRISES

Balaji Constructions

M/S SURINDERAS CONSTRUCTION CO.

V r traders

ANAND ENTERPRISES

akenterprises

R K GOEL ABHEY KUMAR JAIN

M/S Delhi Engineering Co.

AMIR ENTERPRISES

M/S S.K.Electricals