SPL REPAIR/REPLACEMENT OF LT PANELS/CABLES/ GARDEN LIGHTS AND CONNECTED E/M ITEMS AT VARIOUS LOC UNDER GE NAGROTA

Supply, installation and commissioning and testing of LT panel cubical type CPRI Approved certified suitable for 415 volts 3 phase 4 wire, 50 Hz AC supply system, floor mounted, outdoor type factory fabricated duly powder coated inside and out side, outer cover made out of 3.15mm thick CRCA sheet, internal cover and partition made out of 2 mm thick CRCA sheet with angle iron 50 mm x 50 mm x 6mm with 04 legs of 45 cm long covered from all side with front and back openable, weather proof including suitable rating aluminium bus bar for 3 phase 4 wire system, wiring with suitable size copper cable and embeded in brickwork in CM 1:4 not less than 45 cm above ground level with suitable foundation for fixing panel of required size in ground with nuts, bolts and washer etc. complete comprising of following including taking out the old unserviceable panel complete all as specified and directed. Incoming :- (a) ACB 630 Amp 4 pole 50 KA, Manual draw out type with Microprocessor release, Ics=100% of Icu, LCD display, Thermal memory, Zone selectivity, Current & Voltage Measurement, Advance protection, over temperature protection, fault history, V/V and O/V release - 01 No. (b) Alum bus bar 1000 Amp TPN - 01 Set (c) Digital Multifunctional meter Showing V, I, PF, HZ etc with suitable CT ratio-01 No. (d) Indicator lamp LED type (RYB) complete with bakelite fuse fitting- 01 set Outgoing :- (a) MCCB 4 pole, 400 Amp, 50 KA, 415 volts Adjutable Thermal and Magnetic setting with Ics = 100 % Icu - 02 No.s (b) MCCB 4 pole, 200 Amp, 25 KA, 415 volts Adjutable Thermal and Magnetic setting with Ics = 100 % Icu - 02 Nos (c) MCCB 4 pole, 125 Amp, 25 KA, 415 volts Adjutable Thermal and Magnetic setting with Ics = 100 % Icu - 03 Nos Note: Contractor will have to produce Purchase voucher, Manufacturer test certifiacte at the time of RAR/FB duly signed by all concerned.

Supply, installation and commissioning and testing of LT panel cubical type CPRI Approved certified suitable for 415 volts 3 phase 4 wire, 50 Hz AC supply system, floor mounted, outdoor type factory fabricated duly powder coated inside and out side, outer cover made out of 3.15mm thick CRCA sheet, internal cover and partition made out of 2 mm thick CRCA sheet with angle iron 50 mm x 50 mm x 6mm with 04 legs of 45 cm long covered from all side with front and back openable, weather proof including suitable rating aluminium bus bar for 3 phase 4 wire system, wiring with suitable size copper cable and embeded in brickwork in CM 1:4 not less than 45 cm above ground level with suitable foundation for fixing panel of required size in ground with nuts, bolts and washer etc. complete comprising of following including taking out the old unserviceable panel complete all as specified and directed. Incoming :- (a) MCCB 4 pole, 400 Amp, 50 KA, 415 volts Adjutable Thermal and Magnetic setting with Ics = 100 % Icu - 01 No. (b) Alum bus bar 600 Amp TPN - 01 Set (c) Digital Multifunctional meter Showing V, I, PF, HZ etc with suitable CT ratio-01 No. (d) Indicator lamp LED type (RYB) complete with bakelite fuse fitting- 01 set Outgoing :- (a) MCCB 4 pole, 315 Amp, 36 KA, 415 volts Adjutable Thermal and Magnetic setting with Ics = 100 % Icu - 01 No. (b) MCCB 4 pole, 200 Amp, 25 KA, 415 volts Adjutable Thermal and Magnetic setting with Ics = 100 % Icu - 02 Nos (c) MCCB 4 pole, 125 Amp, 25 KA, 415 volts Adjutable Thermal and Magnetic setting with Ics = 100 % Icu - 06 Nos Note: Contractor will have to produce Purchase voucher, Manufacturer test certifiacte at the time of RAR/FB duly signed by all concerned.

Supply, installation and commissioning and testing of LT panel cubical type CPRI Approved certified suitable for 415 volts 3 phase 4 wire, 50 Hz AC supply system, floor mounted, outdoor type factory fabricated duly powder coated inside and out side, outer cover made out of 3.15mm thick CRCA sheet, internal cover and partition made out of 2 mm thick CRCA sheet with angle iron 50 mm x 50 mm x 6mm with 04 legs of 45 cm long covered from all side with front and back openable, weather proof including suitable rating aluminium bus bar for 3 phase 4 wire system, wiring with suitable size copper cable and embeded in brickwork in CM 1:4 not less than 45 cm above ground level with suitable foundation for fixing panel of required size in ground with nuts, bolts and washer etc. complete comprising of following including taking out the old unserviceable panel complete all as specified and directed. Incoming :- (a) MCCB 4 pole, 315 Amp, 36 KA, 415 volts Adjutable Thermal and Magnetic setting with Ics = 100 % Icu - 01 No. (b) Alum bus bar 500 Amp TPN - 01 Set (c) Digital Multifunctional meter Showing V, I, PF, HZ etc with suitable CT ratio-01 No. (d) Indicator lamp LED type (RYB) complete with bakelite fuse fitting- 01 set Outgoing :- (a) MCCB 4 pole, 250 Amp, 36 KA, 415 volts Adjutable Thermal and Magnetic setting with Ics = 100 % Icu - 02 Nos. (b) MCCB 4 pole, 200 Amp, 25 KA, 415 volts Adjutable Thermal and Magnetic setting with Ics = 100 % Icu - 01 No. (c) MCCB 4 pole, 125 Amp, 25 KA, 415 volts Adjutable Thermal and Magnetic setting with Ics = 100 % Icu - 03 Nos Note: Contractor will have to produce Purchase voucher, Manufacturer test certifiacte at the time of RAR/FB duly signed by all concerned.

Supply, installation and commissioning and testing of LT panel cubical type CPRI Approved certified suitable for 415 volts 3 phase 4 wire, 50 Hz AC supply system, floor mounted, outdoor type factory fabricated duly powder coated inside and out side, outer cover made out of 3.15mm thick CRCA sheet, internal cover and partition made out of 2 mm thick CRCA sheet with angle iron 50 mm x 50 mm x 6mm with 04 legs of 45 cm long covered from all side with front and back openable, weather proof including suitable rating aluminium bus bar for 3 phase 4 wire system, wiring with suitable size copper cable and embeded in brickwork in CM 1:4 not less than 45 cm above ground level with suitable foundation for fixing panel of required size in ground with nuts, bolts and washer etc. complete comprising of following including taking out the old unserviceable panel complete all as specified and directed. Incoming :- (a) MCCB 4 pole, 250 Amp, 36 KA, 415 volts Adjutable Thermal and Magnetic setting with Ics = 100 % Icu - 01 No. (b) Alum bus bar 400 Amp TPN - 01 Set (c) Digital Multifunctional meter Showing V, I, PF, HZ etc with suitable CT ratio-01 No. (d) Indicator lamp LED type (RYB) complete with bakelite fuse fitting- 01 set Outgoing :- (a) MCCB 4 pole, 200 Amp, 36 KA, 415 volts Adjutable Thermal and Magnetic setting with Ics = 100 % Icu - 02 Nos. (b) MCCB 4 pole, 125 Amp, 25 KA, 415 volts Adjutable Thermal and Magnetic setting with Ics = 100 % Icu - 02 Nos Note: Contractor will have to produce Purchase voucher, Manufacturer test certifiacte at the time of RAR/FB duly signed by all concerned.

Supply, Fixing , Commissioning and testing of CPRI approved outdoor cubical type LT bus bar box suitable for 415 V, 3 Phase , 4 wire 50 Hz , AC Supply system fabricated from MS sheet supported with 04 legs of 45cm long made of iron angle 25x25x4mm thick totally encloused ,dust, weather & vermin proof, 3.15mm thick for outer shell and 2 mm thick for inner shell having MS section not less than 50x50x6 mm thick having TPN aluminium busbar of capacity 400 Amps mounted on porcelain insulator duly drilled hole for cable connection including front and rear side opening with locking arrangement with Digital Multifunctional meter Showing V,I, PF , HZ etc with suitable CT ratio also with MCCB 4P 250 Amp, 36 KA, 415 Volts 50 Hz with adjustable thermal and adjustable magnetic setting and provn for incoming and outgoing cables with glands including control wiring with minimum 2.5 sqmm PVC insulated copper conductor for measuring of voltage, amp with indicators RYB ,painting with two coat of smoke grey synthetic enamel paint over a coat of red oxide primer, complete including taking down old unserviceable one complete all as specified and directed. Note:- (i) Bus bar box shall be mounted on brickwork in CM 1:4 not less than 30 cm above ground level with suitable foundation, rendering 15 mm in CM 1:6 and two coats of cement base paint and the rates shall be inclusive in the quoted rate. (ii) Contractor will have to produce Purchase voucher, Manufacturer test certifiacte at the time of RAR/FB duly signed by all concerned.

Supply, Fixing , Commissioning and testing of CPRI approved outdoor cubical type LT bus bar box suitable for 415 V, 3 Phase , 4 wire 50 Hz , AC Supply system fabricated from MS sheet supported with 04 legs of 45cm long made of iron angle 25x25x4mm thick totally encloused ,dust, weather & vermin proof, 3.15mm thick for outer shell and 2 mm thick for inner shell having MS section not less than 50x50x6 mm thick having TPN aluminium busbar of capacity 250 Amps mounted on porcelain insulator duly drilled hole for cable connection including front and rear side opening with locking arrangement with Digital Multifunctional meter Showing V,I, PF , HZ etc with suitable CT ratio also with MCCB 4P 160 Amp, 25 KA, 415 Volts 50 Hz with adjustable thermal and adjustable magnetic setting and provn for incoming and outgoing cables with glands including control wiring with minimum 2.5 sqmm PVC insulated copper conductor for measuring of voltage, amp with indicators RYB ,painting with two coat of smoke grey synthetic enamel paint over a coat of red oxide primer, complete including taking down old unserviceable one complete all as specified and directed. Note:- (i) Bus bar box shall be mounted on brickwork in CM 1:4 not less than 30 cm above ground level with suitable foundation, rendering 15 mm in CM 1:6 and two coats of cement base paint and the rates shall be inclusive in the quoted rate. (ii) Contractor will have to produce Purchase voucher, Manufacturer test certifiacte at the time of RAR/FB duly signed by all concerned.

Supply, installation and commissioning and testing of LT panel cubical type suitable for 415 volts 3 phase 4 wire, 50 Hz AC supply system, floor mounted, outdoor type factory fabricated duly powder coated inside and out side, outer cover made out of 3mm thick CRCA sheet, internal cover and partition made out of 2 mm thick CRCA sheet with angle iron 50 mm x 50 mm x 6mm with 04 legs of 45cm long covered from all side with front and back openable, weather proof including suitable rating aluminium bus bar for 3 phase 4 wire system, wiring with suitable size copper cable and embeded in brickwork in CM 1:4 not less than 45 cm above ground level with suitable foundation for fixing panel of required size in ground with nuts, bolts and washer etc. complete comprising of following including taking out the old unserviceable panel complete all as specified and directed. Incoming:- (a) MCCB 4 pole, 250 Amp, 25 KA, 415 volts AC with adjustable thermal and fixed magnetic setting- 01 No. (b) Aluminium bus bar 400 Amps TPN - 01 Set (c) Digital voltmeter 0-500 volts with selector switch - 01 No. (d) Digital Amp meter 0-300 Amp with selector switch & CTs - 01 No (e) Indicator lamp LED type (R, Y, B) complete with bakalite fuse fitting - 01 Set Outgoing:- (a) MCCB 4 pole, 160 Amp, 25 KA, 415 volts AC adjustable thermal and magnetic setting - 02 Nos (b) MCCB 4 pole, 125 Amp, 25 KA, 415 volts AC adjustable thermal and magnetic setting- 01 No. (c) MCCB 4 pole, 100 Amp, 16 KA, 415 volts AC adjustable thermal and magnetic setting- 02 Nos Note: Contractor will have to produce Purchase voucher, Manufacturer test certifiacte at the time of RAR/FB duly signed by all concerned.

M&L in replacement for earthing complete with copper earth plate electrode of size 60cm x 60cm x 3.15mm thick buried directly in ground (earth pit not less than 2.25 meters below ground level) with top edge of earth plate not less than 1.5 meters below ground level surrounded on all sides by 150 mm thick charcoal & common salt starting from ground below earth plate upto 150mm above Copper plate in alternate layers connected to copper strip 20x3 mm by means of nuts, bolts, thimbles, chuck nuts, washers of GI or steel, PCC (concrete chamber of size 300 mm x 300 mm x 300 mm inside dimension) shall be PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish , internal surface of concrete chamber shall be given 15mm thick plaster in CM 1:4, funnel with wire mesh of 22 gauge, 80 mm thick PCC pit cover 320 mm x 320 mm of RCC 1:2:4 type B-1 using 20 mm graded stone aggregate reinforced with XPM, JALLI pit all as shown in electrical plate No 5 of MES SSR Part-I (2009) as specified including provision of 40mm bore medium grade GI pipe for earth strip protection and 20 mm bore for watering complete , all excavation and earth work & connecting the earthing to an earthing test point /LT Panel/ Transformer as specified and testing on completion for desired result complete all as specified and directed. Note :- Excavation for earthing shall be only through manually but not through JCB or any other machine.

Supply and fix in replacement of GI strip of size 32 x 6 mm for earth continuity conductor or main earthing lead fixed to wall burried in ground fixed alongwith poles complete all as specified and directed.

Supply, laying, jointing and testing in repair XLPE cable insulated,armoured, heavy duty electric cable with aluminium conductor,1100 volts grade, cross-sectional area 400 Sqmm 3.5 core complete all as specified and directed.