PROVN OF 1.5 METER WIDE FOOTPATH FROM BLDG NO P126 TO P129 AT 104 AD REGT AND SPECIAL AND PROVN OF 01X RAMP WITH HARDSTANDING FOR UNIT B VEH IN MT AREA OF 27 MADRAS LOC NEAR BLDG NO P 303 AND REPAIR OF JCOS OFFICE BLDG NO T 34 OF 382 ASC COY AND

Amount

Surface excavation n. exc. (not exceeding 30 cm deep and avg 15 cm deep) and getting out in sof/loose soil complete all as specified and directed.

M&L 75mm thick PCC type C-2, 1:3:6 (40mm graded stone aggt) as in path, hard standing, parking floors, etc., complete all as specified and as directed.

S&F Machine pressed precas concrete interlocking paver block (coloured) any shape and size conforming to IS 15658-2006 of 60mm thick M-35 grade etc complete (with grey cement and pigment) over 50 mm thick sand coushioning complete all as specified and directed by Engr-in-charge.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

S&F PVC (SWR) pipes 160mm single socketed, in any length with rubber ring joints, laid in trenches or in floors

Excavation over area in soft / loose soil nexc. 1.50 m deep complete all as specified and as directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/dense soil complete all as specified and directed.

M&L for plain cement concrete 1:4:8, type D2 using 40 mm graded aggregate in foundations, filling and mass-concrete complete all as specified and directed.

M&L M&L for PCC 1:3:6 type C1(20mm graded stone aggregate) pre-cast solid cement concrete block masonry with solid block exc 10 CM in width and setting in cement moetar 1:4 complete all as specified.

M&L for RCC 1:1.5:3 A1 using (20 graded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves complete all as specified and directed.

M&L for RCC 1:1.5:3 A1 using (20 graded stone aggregate) as in beams, roof beams, lintels over 1.5m span complete all as specified and directed. complete all as specified and directed.

M&L for formwork to soffits/sides of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick (Horizontal or sloping) with rough finished surfaces of concrete in flat complete all as specified and directed

M&L for formwork to sides and soffits of floor or roof beams, beams, lintel beam with rough finished surfaces of concrete in flat complete all as specified and directed

M&L for TMT steel bars, 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with & including MS wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for TMT steel bars, 6mm to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with & including MS wire (annealed) not less than 0.9mm dia or securing with clipscomplete all as specified and directed.

M&L for TMT bars 5mm dia and over upto and including 10mm dia in stirrups cut to length bent to shape etc all as specified

M&L for 5 mm thick rendering in CM 1:3 on fair faces of concrete surfaces and finising even & smooth without using extra cement on ceiling complete all as specified and directed.

M&L hard core broken stone or boulders of 63mm gauge, deposited spread and leveled in layers not exceeding 15cm thick watered and well rammed to a true surfaces complete all as specified and directed

M & L for 100mm thick PCC 1:4:8, type D2, using (40mm graded stone aggregate) as in sub- base of floor complete all as specified

M & L for 100mm thick PCC 1:1.5:3 type A1, using (20mm graded stone aggregate) as in Ramp floor, apron, etc complete all as specified

M & L for moorum / red bajri filling brought from out side MD land, in floors or paving, laid in layers n exc 15cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M&L for preparation of new palstered surfaces and appling three coats of white wash on walls all as specified and as directed.

Returning filling in including spreeding, leveling, watering and well ramming in layers n. exc 25 cm thick in soft /loose soil complete all as directed.

Removing excavated material (soil) n. exc. 50 m and depositing where directed at a level n. exc. 1.5 m above the starting point etc complete all as specified and as directed.

M&L for cutting holes superficial area n. exc 100 sq cm into or through cement concrete slabs, column, etc.without cutting reinforcement complete all as specified and directed.

M&L providing cement concrete 1:2:4, type B-0 using (12.5 mm graded aggregate) as in coping apex stones, bed block, kerbs, slightly rounded or chamfered angles and throating incl necessary formwork complete all as specified and directed.

M & L rendering 15mm thick on brick wall or concrete surface consisting two layers of 5mm thick in cement mortar 1:4 over 10mm thick in CM (1:6) finished even and smooth with using water proofing compound complete all as specified and directed. (Note:- Water proofing compound shall be measured and paid saperately.)

Supply only water proofing compound

M & L for preparation of new plastered or unplastered surfaces of walls including cornices, pilasters etc and applying two coats cement based paint over coat of primer complete all as specified and as directed.

M & L for preparation of old plastered or unplastered decorative surfaces of walls including cornices, pilasters etc and applying one coat cement based paint complete all as specified and as directed.

M&L for preparation of new or previously untreated steel surfaces of any description, not exc. 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

M&L for preparation of new or previously untreated steel surfaces of any description, over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

M&L for complete removing existing treatment on steel surfaces of any description, over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

Dismantling of Galvalume aluminium zinc coating GI based corrugated steel sheets in roofing.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering fixed with self tapping screws complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based plain/corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in ridge/ valley gutter/chajjas etc fixed with self tapping screws complete all as specified and directed.

Dismantling of wrought iron or mild steel work of any description, as in rafters, purlins and wind ties etc.

S&F mild steel rolled sections confirming to grade E-250 (Fe-410W quality A) as in main cross beams, hip or jack rafters / purlins where connected to common rafters etc. fixed with angle cleat or other connecting plates.

S&F mild steel rolled sections confirming to grade E-250 (Fe-410W quality A) in compound girders and stanchions,lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc, built up from two or more beam channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates etc.

M&L for preparation of new steel and iron surfaces of any description exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and as directed.

Demolition of brick work/stone masonry built in cement mortar of any description

M&L for brick work with sub class `B' bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:4 all as specified and directed as in repairs.

Demolition of cement Concrete of any description and in any position not otherwise specifically provided for

M&L PCC 1:2:4 type B-1 (using 20mm graded stone aggegate) as in copinges, plinth band, parapets, ralinges and outer wall upto 60 cm in height etc complete including necessary form work all specified and directed

Dismantling of wall and ceiling boards( fiber pulp insulation etc) or insulation boards/slabs/blankets any thickness including cover fillets all as specified anc directed

S&F GI frame work of size 605 x 605mm, for seamless celing comprising of GI perimeter chanel 0.55mm thick with two unequal flangesof 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/ intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and incl ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre.

S&F hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3mm size 60mm long and expansion hold fasterners 12.5mm dia 40mm long complete all as specified and as directed.

S&F 4mm thick Non asbestos fibre cement building boards (E-boards) fixed or laid/ inserted to timber/GI/Aluminium framework with screws as in ceiling complete.(Make: GYP board/Arm strong/Bison panel or equvalent)

Taking down of cement plaster of any description on brick/stone walls or concrete surfaces etc including raking out joints, hacking for key, scrubbing down with water etc.

M&L for rendering 10mm thick on fair faces of brickwork/stonework or concrete surfaces in CM 1:6 finishing the surface even and even smooth without using extra cement..

M&L 15 mm thick rendering in in two layers 5mm thick inCM 1:4,over 10mm thick cement plaster in CM 1:6 on fair face of brick work/Stone work or concrete surface to be finished even and smooth without using extra cemen Including WPC compound 3% by weight of cement.(Note :a) Intergial WPC Compound shall be used in sencond layer,b) Intergial WPC shall be paid seperately on supply only.

M & L for preparation of new plastered surface of wall and applying two coat of oil bond distemper and 3 mm putty all as specified and directed

M&L preparation of newly plaster surfaces of walls over 10cm width and applying two coats of weather coat exterior paint over a coat of priming paints plaster coat including necessary surface preparation.

Complete Removal of existing treatment on Internal wall and applying two coats of oil emulsion distemper & one coat primer complete all as specified & directed

Material and labour for complete removal of existing treatment from plastered or unplastered surfaces of walls including cleaning with scrapers, any number of coats and any width or girth etc, the area of application should be cleaned thoroughly, remove all dirt, dust and uneven elements from the surface by washing and scraping and all the unevenness in the surface should be corrected by filling the exterior surface, surface should be sanded down with fine grade sand paper for smoothness and applying one coat of exterior primer and 02 coats of Exterior Weather Coat Emulsion Paint of white or tinted shade as per manufacturer instruction complete all as directed and specified.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar .

M&L Glazed ceramic coloured designer tiles in vertical surface 350x250x7mm/450x300x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match 0ver 10mm thick plaster in cement mortar (1:3).(Make: Somany/Johnson/Orient Bell or equivalent)

S&F coloured aluminium anodised sliding window of 3 tire, frame of section 62mm X 32mm X 1.47 mm or appropriate equivalent section and shutters of section 18 mm X 44 mmX 1.35 mm or appropriate equivalent section ,aluminium sections weighting 0.55 Kg/m, fixed with 4.80/5mm thick tinted glass with rubber gasket, handles, locking arrangement and SS wire mesh,aluminium powder coated any colour (powder coating not less than 50 micron) incl making good jambs, cills etcincluding taking down old iron window complete all as specified and directed by the Engr-in-Charge.(make: Hindalco/Indal/Jindal or equvalent) Note : rate shall include all glazing/SS wire cloth, rubber packing, joining, cleats, glazing clips, aluminium snap beading, locking arrangements, handle etc

S & F Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

S&F SS Curtain Rod Decorative pattern as approved by Engr-in-Charge. In repairs

S&F SS Curtain Rod Bracket decorative type all as directed and approved by Engr-in-Charge in repairs

Supply only Integral waterproofing compound

M&L Preparation of old painted wooden surfaces of any description over 10 cm in width/girth and applying one coat of synthetic enamel paint.

Taking down carefully aluminum /copper point wiring (light, fan, switch & power) complete including fittings such as switches, ceiling rose, pendent, by unscrewing from board ,out let box, fitting and fixture such as bulk head fitting, sketch fittings and making good the disturbed rurfaces of walls floors etc complete all as specified and directed by Engr-in-Charge.

Taking down old MCB, DBs/main switch of any size complete all as specified and directed by Engr-in-Charge.

Taking down sub main wire of any size fixed in any position , complete all as specified and directed by Engr-in-Charge.

M & L for Point wiring using approved colour coding as per IS, with multistranded copper conductor 1.5 Sq. mm (nominal area), two single core, PVC insulated and unsheathed FRLSH cable 1100 volts grade ISI-694 marked drawn through in and including heavy duty, PVC concealed conduit of white/ ivory colour including all accessories after chasing in wall/ceiling etc, heavy duty ISI marked including sunk in anodized pressed steel box 1.60 mm thick, 60 mm deep for housing switch socket etc with white laminated 3 mm thick hylam sheet cover ISI marked of suitable size complete including PVC insulated multi stranded copper conductor 1.5 Sq mm FRLSH cable as earth wire to common earth dolly for connection to ceiling rose to earth terminal including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed by Engr-in-charge for following :-

(a) One light point controlled by one, one way switch 5 Amps

(b) One fan point/ exhaust fan point controlled by one, one way switch 5 Amps and regulator

(c) One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board.

(d) One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent board.

Description all as per item No 67 here in before but using 2.5 sq mm single core copper conductor cable of multistranded flame retardant PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point including necessary running of 2.5 sq mm copper conductor flame retardant PVC wire as earth continuity conductor along with wiring and connecting to the common eath dolly.

S&F switch piano flush type single pole one way 5 Amps 230 V.

S&F switch socket out let 3 pin 5 Amps flush type 230 Volts multipurpose.

All as per item No-7 above but 5 Amps and 15 Amps multipurpose ( 3 Pin 15 Amps and one pin 5 Amps controlled by one switch.).

S&F socket out let 3 pin, 5 Amps, 230 Volt multipurpose flush piano type.

S&F fan regulator Electronic Step type (min 5 steps) 2module, 100/120W complete all as specified and directed.

S&F ceiling rose surface backelet ISI marked 2 to 3 terminal complete all as specified and directed.

S & F for LED luminaire 600 mm x 600 mm square LED panel 24/30 watts, 220V AC surface type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling, including connecting up with driver three core flexible copper conductor cable of suitable size with installation complete all as directed by Engineer- in-charge.Make :- Bajaj Cat No BZSSQL 36L LED WH GX or Philips Cat Part No SM366C LED32-6500 PSU OD WH, or Wipro Cat part No CRCO10R036HP57G2.

S & F for LED tube light fitting 2 feet x 10 watts with high out put diffuser, decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose to fitting complete all as specified and as directed.

S & F for wall mounted LED tube light fitting 20 watts batten for surface mounted, anodized extruded aluminium housing, high transmissitivity diffuser, high lumen ouput box type fitting, 230 volts and intregrated electronic driver connector block etc complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and as directed. Make :- Make Bajaj Cat part No BCLAB 20W WH LED P, Wipro Cat part No LL20-281-XXX065-ALI or its equvalent in Philips, Havells.

S & F for sheet metal enclosure MCB DB SPN 8 way with 200 Amps rated bus bar 240 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed.

S & F for MCB Single pole and neutral rated capacity 32 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

S & F for MCB Single pole rated capacity 5 to 32 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

M & L for Sub main wiring with approved colour coding as per IS with two single core PVC insulated FRLSH cable with stranded copper conductor of size 6 Sq mm nominal area and drawing into suitable size of PVC non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc one run of PVC insulated with 6.0 Sqmm (nominal area) stranded copper conductor FRLSH cable as earth wire complete all as specified and as directed. Note:- Two runs of 6 sqmm cable,one run of 6 sqmm cable and one run of PVC conduit will be measured as one unit

Taking down & Refixing Ceiling fan 1200mm sweep AC, 240 volts,Metal body ,after cleaning , greasing and painting with synthetic enamel paint by spreying including filling cavities with filler, one coat after cleaning all dusts etc and connecting up including provision of flexible wire from ceiling rose/connector to fan complete all as specified and directed.

Quick Building Service (BID ID -3090382)

SHRI SAINATH ENGINEERS (BID ID -3089474)

Hirachand Sunderji and co (BID ID -3089979)

ABR Trading Co (BID ID -3088401)

SHELANI CONSTRUCTION (BID ID -3087153)