GE/U(N)-61/2023-24 PROVN OF ADDN/ALTN TO MT GARAGE BLDG NO NP-21 AND VEH PARKING SHED IN FRONT OF CSD CANTEEN UNDER GE (NORTH) UDHAMPUR

Amount

Aluminium sliding window, ventilator shutter with chowkhat of powder coated, 5mm thick glass, stainless steel wire gauge for shutters, etc, without sash bars, aluminium sections (20076 weighing 1.608 Kg/m) (thickness or powder coating not less than 50 micron) including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as 5mm thick tinted glass, stainless steel wire gauge for shutter three track (02 Nos shutter glazed & 01 No wire gauge) etc, complete all as specified and directed by Engr-in-Charge.

Demolition of cement concrete (un reinforced) as in ground floor and paving area of any type and any thickness, complete all as specified and as directed by Engr-in-Charge.

Taking down cement or cement lime plaster on brick or stone walls etc of any description including racking out joints hacking for key scrubbing down with water etc complete all as specified and as directed by Engr-in-Charge.

Dismantling of wall and ceiling board (fibre/pulp, insulation, etc) or insulation boards/slabs/blankets, any thickness, including cover fillets all as specified and as directed by engineer in charge.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) not exc 1.5 square metre each complete all as specified and as directed by Engr-in-Charge.

Taking down chowkhats or frame exc 1.5 sq.m but n.exc 4 sq.m with shutter (without taking off shutters from the frame) and remove from sitecomplete all as specified and as directed by Engr-in-Charge.

Dismantling of plain or corrugated roof sheeting any thickness including Nainital or similar Pattern roof covering etc complete all as specified and as directed by Engr-in-Charge.

Dismantling of structural steel work in any description complete all as specified and as directed by Engr-in-Charge.

Demolition of brick work or stone/boulder masonry built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and as directed by Engr-in-Charge.

Dismantling floors hearth and tiling or wall tiling including cement mortor bedding (but not backing) removing rubbish of Premises of any description or thickness in floor/dado, apron, etc laid bedded and pointed in any mortar,complete all as specified and as directed by Engr-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds glazed with putty or fixed with beads, complete all as specified and as directed by Engr-in-Charge.

Taking up or down steel tubing and connection, including cleaning for re-fixing or removal to store of size of pipe 15 mm bore laid on floor or wall complete all as specified and directed.

Taking up or down steel tubing and connection, including cleaning for re-fixing or removal to store of size of pipe 20 mm bore laid on floor or wall complete all as specified and directed.

Dismantling water tanks of 1000 ltrs and removing from site, complete all as specified and as directed.

Brick work with sub class ‘B’ bricks straight or curved on plan exc 6 m mean radius built in cm 1:4 complete all as specified and as directed by Engr-in-Charge.

Rendering 10mm thick on fair faces of brick work in cm 1:6 finished even and smooth w/o using extra cement complete all as specified and as directed by Engr-in-Charge.

Rendering 15mm thick on stone masonary surfaces or surface other than fair face of brick work in cm 1:4 finished even and smooth w/o using extra cement complete all as specified and as directed by Engr-in-Charge.

Rolled mild steel section of angle, tee, flats,and plates as in roof trusses, purlines, rails, etc and the like fixed with angle cleats and connecting plates including welding,Gde FE-410-0 or FE-310-0 complete all as specified and as directed by Engr-in-Charge.

Pre-painted galvalume zinc coating 120 gram/Sqm GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and as directed by Engr-in-Charge.

Pre-painted galvalume zinc coating 120 gram/Sqm GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and as directed by Engr-in-Charge.

Coloured vitrifired ceramic tiles 08 to 10mm thick (square) polished , light shade, area of each tiles exc 0.18 sqm but n.exc 0.38Sq.m (min. size 600mm x 600mm) in floor etc, set and jointed in neat cement slurry and pointed in white or coloured cement incl 15mm thick screed bed in CM (1:6) complete all as specified and as directed by Engr-in-Charge.

Vitrified ceramic tiles 08 to 10mm thick, polished, coloured, light shade in pieces of required width cut out of 600mm x 600mm size, in skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including10 mm thick rendering in cement mortar 1:3 complete all as specified and as directed by Engr-in-Charge.

Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

25mm thick PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) as in floor sub base of tiles complete all as specified and as directed by Engr-in-Charge.

Non skid ceramic coloured tiles 7 to 8 mm thick (sqare/ rectanglear) area of each tile exc 0.11sqm but n exc 0.18 sqm in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 15mm thick screed bed in Cement mortar (1:6) complete all as specified and directed.

Glazed ceramic coloured tiles in vertical surfaces 350 x 250 x 7mm/450mm x 350mm x 7 mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10 mm thick rendering in Cement mortar 1:4 complete all as specified and directed.

Machine cut kota stone slab flooring 18-20mm thick over cement screed base 15mm thick in cm 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete

Kota stone slab 18-20mm thick in riser of steps, skirting , dado and pillar laid over 10mm thick rendering in cm 1:4 and jointed with pigment to match the shade of the slab including rubbing and polishing complete

50mm thick PCC 1:3:6 type C1 (using 20mm graded stone aggregate) as in plinth protection finished even & smooth with out using extra cement incl making joints 10mm wide and 30mm deep at spacing n more than 2.5m and at corners mandatory and filled with sealing compound grade A complete all as specified and as directed by Engr-in-Charge.

S&F false ceiling with fibre cement designer tile ivory painted (high pressure steam cured) of 4 mm thickness (as per IS:14862) of size 595 x 595 mm and any one of the desin (occeanic, lake & hill,cascade or electra) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 gms, both side inclusive) consisting of main 'T' runner with suitably spaced joints to get required length, and 15x32 mm made of 0.30 mm sheet, and cross'T' at 600mm c/c to form a grid including, required cutting/making, opening for services like diffusers,grills,light fittings, fixures,smoke detectors etc . Main 'T' runners to be suspended from ceiling using GI soffit cleats fixed to existing rafter, purlin, etc with gavanised Butterfly level clips, spaced at 1200 mm c/c along main T, bottom exposed width of 15 mm of all T- sections shall be centra black pre-painted with polyester paint, and having a load bearing capacity of 12 kg/sqm, and refixed all exesting electric wiring and fixture all complete at all heights as per direction of Engineer-in -Charge.

Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on vertical/inclined wall surface complete all as specified and as directed by Engr-in-Charge.

5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to complete all as specified and as directed by Engr-in-Charge.

M&L for frame work as in grills, guard bars railings etc conforming to Fe-290 Gde-E-165 etc complete all as specified and directed by Engr-In-Charge

Pressed steel frames for doors of size 165 x 60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate,etc,complete all as specified and as directed by Engr-in-Charge.

Cement concrete Type B2 1:2:4 in walls or retaining walls, in pressed door frame of any thickness, size or shape including pilasters, buttresses columns, pillars,boundary pillars and posts

S&F 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed by Engr-in-Charge.

S&F 35mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and as directed by Engr-in-Charge.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm fixing with wooden/steel beads, complete all as specified and as directed by Engr-in-Charge.

Sheet glass 4mm thick ordinary quality and glazing with beading/oil putty in square n/exc 0.5 Sqm each pane complete all as specified and as directed by Engr-in-Charge.

S&F for Steel ventilators, fixed type, with glazing bars complete all as specified and as directed by Engr-in-Charge.

Preparation of new plastered surfaces by using necessary compound of Altek/Birla white putty 1 to 1.2mm thick to obtain smooth/even finish using sand paper and applying two coats of distemper oil emulsion over a coat of alkali resistant cement based priming paint complete all as specified and as directed by Engr-in-Charge.

Preparation of old plastered or un-plastered surface by brooming down or steel wire brushing,scraping down smoke soot, moulds moss and efflorences salts and trading oil and greasy spots and filling nails marks with compound of wall putty and sand papering and applying one coat of distemper oil emulsion white or tinted,complete all as specified and as directed by Engr-in-Charge.

Prepration of new plaster surfaces of wall and applying two coats of cement based paint over a coat of alkali resistant cement base primer on wall surfaces complete all as specified and as directed by Engr-in-Charge.

Preparation of new wooden painted surface of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of aluminium primer complete all as specified and as directed by Engr-in-Charge.

Preparation of new or previously untreated steel and iron surface of any description exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer, complete all as specified and as directed by Engr-in-Charge.

200mm Aluminium, anodised, barrel tower bolts of extruded section and fixed, complete all as specified and as directed by Engr-in-Charge.

300mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed by Engr-in-Charge.

150 mm size mild aluminium handles cast type anodised all complete all as specified and as directed by Engr-in-Charge.

100mm size butt hinges, medium weight cold rolled mild steel complete all as specified and as directed by Engr-in-Charge.

300mm mild steel ordinary rat tail rod pattern spring including roller plate complete all as specified and as directed by Engr-in-Charge.

Floor door stopper of alumium body and tongue anodised with land drawn steel spring overall lengthof cover plate 140mm fixed with screw, complete all as specified and as directed.

S&F 1mm thick Mild steel sheet eaves gutters of 150mm dia, glvanised class 3, half round with rounded edges complete all as specified and as directed by Engr-in-Charge.

Mild steel cromium plated 20mm dia (curtain rod) with fixing brackets,stops,roller etc complete all as specified and as directed.

15 mm dia bore medium grade galvanised tubes Steel water tubing with all fittings and fixed to walls and ceiling or laid in floors complete all as specified and directed.

20 mm dia , medium grade, galvanised tube Steel water tubingwith all fittings and fixed to walls and ceiling or laid in floors complete all as specified and directed.

Cutting chases, pining in, making good to facings where required and pointing in cement mortar 1:3, for concealed water tubing etc and maing good, cutting exc 10cm and not exc 20 cm girth complete all as specified and directed.

Vitreous china,white, wash hand basin, flat back of size 550x400mm, white including MS brackets including cutting for and pinning including 32mm dia CP brass waste coupling and PVC waste pipe, fixed in repair complete all as specified.

CP Towel Ring 200mm dia Fixed in repair complete all as specified and as directed by Engineer-in-Charge.

20mm dia brass chromium plated tubular towel rails,D type,60 cm long between flanges Fixed in repair complete all as specified and as directed.

Centre hole mixer for mixing hot & cold water for wash hand basin, cast copper alloy, with dual capstan heads, chromium plated, screwed down high pressure, with lettered 'Hot' & 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe suitable for 15mm bore, fixed in repair complete all as specified and directed. Make : Jaquar, Cera or equivalent as approved by GE

Angle valve, brass, chromium plated, fancy type, with capstan head handle screwed down high pressure, including CP brass wall flanges; screwed for 15mm bore pipe connection fixed in repairs complete all as specified and directed. Make : Jaquar, Cera or equivalent as approved by GE

Bib taps, brass, chromium plated, fancy type, long nose, with capstan head handle screwed down high pressure, including CP brass wall flanges; screwed for 15mm bore pipe connection fixed in repairs complete all as specified and directed. Make : Jaquar, Cera or equivalent as approved by GE

PVC flexible connections 450mm long 15mm dia with brass flange nuts & washers complete all as specified & directed.

PVC flexible connections 600mm long 15mm dia with brass flange nuts & washers complete all as specified & directed.

Stop valves, brass, fancy type, chromium plated with long shank and cup (concealed type), screwed down high pressure, with capstan head handle, screwed both ends for iron pipe or for unions and fixed. Make : Jaquar, Cera or equivalent as approved by GE.

Soap dish, brass, chromium plated, heavy duty, fixed to wall with plugs with brass cadmium plated screws complete all as specified and directed. Make : Jaquar, Cera or equivalent as approved by GE

CP brass grating 75mm dia, centre hole, complete all as specified and as directed.

CP brass grating 75mm dia, complete all as specified and as directed.

Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of 1000 litres capacity, hoisted and fixed in position including connecting up pipes complete all as specified and directed.(fixed in repair)

Ball brass valve 20mm dia high pressure with polythene float and fly nut complete all as specified and directed. Make Parko cat part No 1527

PVC (SWR) Gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and as directed.

S&F 75mm dia PVC (SWR) floor trap/nahani trap, plain with grating including jointing with solvent cement etc complete all as specified and as directed.

S&F for 75mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors in repair etc complete all as specified and as directed.

S&F for 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls fixed in repair etc complete all as specified and as directed.

S&F for 110mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors in repair etc complete all as specified and as directed.

S&F for 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls fixed in repair etc complete all as specified and as directed.

S&F in repairs 75mm PVC (SWR) bends any radius etc complete all as specified and as directed.

S&F in repairs110mm PVC (SWR) bends any radius etc complete all as specified and as directed.

S&F in repairs 75mmPVC (SWR) branch piece, double (double Y) equal or unequal with access door etc complete all as specified and as directed.

S&F in repairs 110mmPVC (SWR) branch piece, double (double Y) equal or unequal with access door etc complete all as specified and as directed.

S&F for 75mm PVC (SWR) vent cowl etc complete all as specified and as directed.

S&F in repairs PVC (SWR) reducers etc complete all as specified and as directed.

Granite work with 20mm thick slab, table rubbed and polished, in steps, window cills, cooking platforms and like in single piece set in neat cement slurry and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite laid over and including 15mm thick screed bed or bedding layer in cement mortor (1:4) complete all as specified and directed.

Sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in CM to dwarf wall or incl fixing cantilever brackets and connecting union to pipe overall size 915mmx 460mm bowl size 410mmx330mmx160mm, fixed in repair complete all as specified and as directed. Make: Neelkanth, Nirali

Sink wall mixture, brass, chromium plated, fancy type, with capstan head handles screwed down high pressure, with lettered 'hot' and 'cold', including CP brass wall flanges and necessary extension nipples screwed for 15mm bore pipe connection, fixed in repair, complete all as specified and directed. Make : Jaquar, Cera or equivalent as approved by GE

Chequered vitrified tiles 30cm x 30cm x 10mm thick coloured with grey cement & admixtures laid over 15mm thick cement mortar 1:4 set, jointed and pointed in neat cement slurry in floors, complete all as specified and as directed.

Excavation over area not exc 1.5m deep in any type of soil and getting out complete all as specified.

Excavation in trenches in any type of soil n exc 1.5m deep and not exc 1.5m wide for laying of under ground cable, electric pole and getting out complete all as directed.

Surface excavation (not exceeding) 30cm deep and averaging 15cm deep and getting out in Soft/loose soil complete all as specified as directed.

Returning, filling in including spreading, levelling, watering and well ramming in layers not exc 25cm complete all as specified.

Removing surplus spoil to n exc. 50m and deposited where directed at a level not exceeding 1.50m from the starting point., all as specified .

Cement concrete 1:4:8, type D-2 (using 40mm graded crushed stone aggregate) as in foundation filling and mass conctere all as specified.

Walling of random rubble stone masonry uncoursed well bonded, bedded and solidly hearted, built in cement mortar (1:6) including providing weep holes complete all as specified (if PCC bond stone shall be measured and paid separately).

Plain Cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in coping, benching including weathering slightly rounded or chamfered angles as directed including necessary form work and finishing the exposed surfaces complete, all as specified.

Hand packing (any thickness) of broken stone boulders at back of wall over arches etc and raising (or lowering) to the required label.

PVC pipe 110 mm dia low density of pressure rating 10Kg/Sqcm (in short lengths) fixed in walls as weep holes as in retaining wall complete all as specified.

Precast cement concrete 1:3:6 type B-1 (using 20mm graded crushed stoen aggregate) set in cement morar 1:6 as in bond stones of any thickness and size or shape complete all as specified and directed

Extra over stone walling for hammer dressing to face stone and dressing of face beds and joints as specified of random rubble walling, uncoursed or brought up to course, hammer dressing with maximum depression on face from straight edge held against the dressed surface not exceeding 20mm for granite or trp stone, all as specified.

Raised pointing to random rubble walling uncoursed in CM (1:3) complete all as specified

Excavating in post hole (or similar holes) as in hard/dence soil each n exc 0.5 cu. M, getting out, complete all as specified and directed.

PCC 1:3:6 type C2 (using 40mm graded stone aggregate) as in foundation for fencing post filling, and mass concrete, complete all as specified and directed.

Brick work with sub class ‘B’ bricks straight or curved on plan exc 6 m mean radius built in cm 1:6 complete all as specified and as directed by Engr-in-Charge.

M&L for 15 mm thick cement plaster on the fair face of brick or concrete surface in cement mortar 1:4 finished even and smooth without using extra cement, all as specified and directed by the Engr-in-Charge

M&L for two coat of cement base paint over a coat of priming paint over prepared surfaces of newly plastered wall complete all as specified and directed by the Engr-in-Charge

Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade joint with white cement and pigment, set, laid on 50mm thick and cusioning complete all specified and directed.

75mm thick PCC 1:4:8 type D1 (using 20mm graded stone aggregate) as in Sub base complete all as specified and directed.

Taking down carefully point wiring copper / aluminium(light , fan, socket, and power) complete (fittings such as switches ceiling roses, pendent regtulators sockets etc to be measured and paid for separately removing materials to store for keeping of safe custody and making good the disturbed surfaces complete all as specified and as directed.

M&L for point wiring with PVC insulated unsheathed, FRLS 1100 volts grade stranded copper conductor cable single core 1.5 Sqmm for one light / fan point/ bell point controlled by one way switch,, and wire to be drawn in and including concealed conduit of dia not less tham 25mm complete with all accessories including MS sheet metal 1.2 mm thick switch board of suitable size be fixed flush wall , with 3 mm thick ebonite sheet cover and necessary screws , cap washers etc. or to be fixed on wall respectively as directed by EIC and providing earth continuity wire using PVC insulated, un sheathed single core stranded copper conductor FRLS cable of size 1.5 Sqmm.

All as per item No 109 above but for one 3/5 pin socket 5 Amp on same board with cable 1.5sqmm size.

All as per item No 109 above but for one 3/5 pin socket 5 Amp on independent board with cable 1.5sqmm size..

All as per item No 109 above but for 3 pin socket outlet 15 Amps independent with 2.5 sqmm incl contious earthign with multistanered copper conductor PVC insulated unsheathed size 2.5 Sqmm complete all as specified and directed by Engr-in-Charge.

S&F Switch Piano flush type single pole 5 Amps One way, all as specified and directed by Engr-in-Charge.

S&F socket flush type single pole 5 Amps one way, all as specified and directed by Engr-in-Charge.

S&F Switch Socket combination 2 in 1, 3 pin, 5 and 15 Amp flush type universal all as specified and directed by Engr-in-Charge.

S&F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc, as reqd all as specified and directed by Engr-in-Charge.

S&F Ceiling rose, 3 terminal, PVC/ Polycarbonet, isolated body complete asll as specified and directed by Engr-in-Charge.

S&F Electric bell (Ding dong) AC 230/250 volts grade single pole ISI marked fixed in replacement, complete all as specified and as directed.

S&F switch piano flush type for bell push 5 Amps fixed in replacement, complete all as specified and directed.

S&F LED light fitting PLUTO NEO PANEL 2'x2' PLR 36 watt LED 857S environmental friendly, new generation, aesthetically designed, ultra modern recess mounting luminaire with high brightness SMD LEDs as light source suitable for armstrong/ grid/ ceiling all as specified and directed by Engr-in-Charge.

S&F Slim linear LED lighting fixture 20 watt LED battern, with full base of extruded aluminium section acting as a heat sink with closed back, isolated dirver, complete making all connection unsing 1.5 sqmm copper conductor multistandard PVC insulated 2 core flexible cable with flexible PVC pipe from ceiling rose to fittings complete including taking down old US tube light fitting 1x36W and taken in schedule of credit all as per the directed by Engr-in-Charge.

S&F in replacement E-Lite LED Curve lighting fixture for mirror 10/12 watt LED batten,2' long with full base of extruded Aluminium body environmental friendly, energy efficient ready to use pack with isolated driver, complete making all connection using 1.5 sqmm copper conductor multistrandard PVC insulated 2 core flexible cable with flexible PVC pipe from ceiling rose to fittings complete including taking down old unserviceable tube light fitting 1x 18 watt from the site reuse to measured seprately or disposal by credit all as per the directed

S & F LED Bulk head (6500K) fitting of 09/10 Watt surface mounting type extruded aluminium body with diffuser complete with testing all as specified and directed.

Supply and fixing LED street light fitting 35 watt 230 V AC outdoor type with high pressure die cast aluminum housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection compete

Taking down fan, ceiling cable end, dismantling blades and kept in safe custody for refixing on same location all as specified and directed by engineer in charge.

M&L for repair of ceiling fan/exhaust fan 1200/300mm sweep of any make obtained from above item, oiling, greasing cleaning slot, over hauling & replacement of defective nut bolts washer etc including painting. If as per site requirement fan will be found burnt rewinding will be provide by the contractor as per unit quoted rate all as specified and directed.

Hanging /fixing only ceiling fan/Exhuast fan and connecting up including provision of cable from ceiling rose or connector to fan obtained from site

S&F electric water heater, storage type steel body wityh copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc.

Supply & fix fans ceiling complete with fixing accessories 230 V, 1200 mm sweep, BEE/ BLDC 5 star rated complete

Supply and fixing Exhaust fans steel body,AC ingle phasee 230 volts of size 450 mm sweep with blades and frame and louver complete all as specified and directed

M&L for submain wiring with 2X6.0 SQMM+1X6.0SQMM Earth Wire single core PVC insulated FRSL sheathed cooper cable connecting to common earth dolly in and including heavy duty PVC Concealed Conduit as per site requirement including taking down old submain wiringand direction by EIC, all accessories complete all as specified and directed.

S&F single pole and neutral sheet steel powder coated Disttubution board for MCBs fitted with bus bar, Neutral lingk, Earth Bar and Din rail sutable for use on 240 V, 50Hz supply double door SP&N DB system 08 ways

S&F 'C' series SPN MCB 40 to 63 Amps 240V, 50Hz, 10KA lighting and other domestic loads incl all termnials, fitting etc.

S&F 'C' series SP MCB 06 TO 32 MPS 240v, 50hZ, 10kA suitable for lighting and other domestic loads incl all terminals, fitting etc

M&L for replacement of single pole and neutral enclosure with a two pin and earth lug and socket complete with one single pole MCB of 20 Amps 240 volt capacity complete all as directed.

M&L Earthing complete with galvanised steel earth plate electrode 60x60 cmx6mm thick, buried directly in ground (earth pit not less than 2.25 meteres deep below gournd level) with top edge of the plate not less than 1.5 meteres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No-5 of MES Part-1 fixed in replacement including testing on completion including the material and labour of the following :- (a) Excavation and earth work for drilling hole for electrode in any type of soil. (b) PCC Pit in cement concrete 1:2:4 type B-1. (c) Precast RCC cover with suitable handle 40mm thick in PCC 1:2:4 type B-1, reinforced with welded steel wire fabric weighing not less than 1.87 Kg/Sqm. (d) Funnel with watering pipe of GI protection pipe 5 mtr long for protection of earthing lead from mechanical injury or termpering. (e) Requistire quanitiy of common salt and charcoal. (f) Testing of Earthing.

S&F sheet metal TPN DBs-DPX3 160 MCCB DBs 04 way (DPX3 250+12) with metal Double door

S&F DPX3 thermal magnetic MCCB 4 pole 160 Amps 415 Volts 16 KA including making necessary arrangement all as specified and directed by Engr-in-Charge for MCCB DB. Make Legrand, Cat Part No : 4202 07 or equivalent to Shnieder

S&F 415V 10KA 'C' curve miniature circuit breaker (MCB) of TPN 40 to 100 AMP and current carrying capacity in the DB complete with connection testing and commissioning

Supply and lay XLPE insulated screened PVC bedded, galvanized steel strip wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded sluminium conductor of size 16 sqmm 2 core in trenches/ floor/ pole/GI pipe complete including cuttings/ chasing to any surface and making good to the distrubed surface to match the existing all as specified and directed.

M&L for dry sand cushioning to under ground cables provided with a layer of sand 8 cm deep before laying the cable, 15 cm depth after laying cable & stretching the cable all apecified and directed.

Supply and lay brick class 'B' covering as mechanical protection to cable with well burnt all as specified and directed

M&L GI tubing light grade with all fitting and fixed in wall and floor or fixed to pole of size 40mm dia all as specified and directed.

M/S IMTESH BHAT

RAMAN KUMAR