Certain petty repair for day to day maintenance works including internal electric repairs under AGE B/R-I at Suratgarh Mil Stn

Amount

Taking down old unserviceable cooler stand of any size & any type fixed on external face of walls at cill level of windows at ground floor and first floor of building including cutting holes and making good the disturbed portion with cement mortar or PCC after refixing new cooler stand complete all as specified and directed by Engineer-in-charge.

Taking down chowkat or frame with shutters including fitting and fixtures area not exc 1.5 Sqm each (without taking off the wooden shutters from the frame) including cutting holes for hold fasts and making good disturbed surface with cement mortor or PCC after fixing new chowkats complete all as specified and directed by Engineer-in-charge.

Taking down shutters of any description exc 1 Sqm and not exc. 2 Sqm each complete all as specified and as directed by Engineer-in-charge.

Taking down existing aluminium door frame including glazed shutter & builders hardware complete of area 2 sqm and not exc 4 sqm each of any description and refixing in the same opening after carying out necessary repair & replacement of unserviceable components / hardware to make if fully functional complete all as specified and directed by Engineer-in-charge. Note :- (i) Cost of new jointing cleat, aluminium beading, glazing clips, rubber packing stays including cutting of old style etc and adjusting the same appropriately deemed to included to in the unit rate of this items nothing extra shall be paid on this account. (ii) Glazing, new aluminium section for frame / shutter, builders hardware such as handles hinges door closure, floor door spring shall be measured & paid for seprately. (iii) Loose corner joints of frame & shutter shall be tightned by providing shuitable cleats made out of aluminium angle of appropriate size fixed with nut & bolts to make joints at 90 degree.

Resecuring or easing & adjusting without taking down shutters exceeding 1.0 Sqm but not exc 2.0 sqm each complete all as specified & directed by Engineer-in- charge.

M&L for 30mm thick flush shutter solid core construction with block board core & ply wood face panels, commercial type on both faces including 1mm thick wood grain printed PVC sheet fixed or laid on to flush door by using rubber based adhesive at site as per specification as per SSR Part-I complete all as specified and directed by Engineer-in-charge.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately) complete all as specified and directed by Engineer-in-charge. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. Note: stainless steel butt hinges and necessary S S screws shall be paid separately.

S&F 35mm thick factory made glazed and skeleton shutters made of second class hard wood (Bonsum/Hollock), open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in SSR Part I Section 8 Clause 8.24 (a) kiln seasoned and chemically pressure treated fixed to chowkat complete all as specified and directed by Engineer-in-charge.

S&F 35 mm thick factory made plain framed, panelled shutter (any number of panels) with lock rail and panel of 9mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces. The size of rail and styles as per IS : 1003 (Part-I), kiln seasoned and chemically pressure treated using second class Hard Wood (Hollock or Bonsum) complete all as specified and directed by Engineer-in-charge.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube complete all as specified & shown in relevant drawing of item No. 08095 in MES Schedule (Part-II) and directed by Engineer-in-Charge

S&F 30mm thick factory made solid core PVC door shutter (style) consisting of frame made out of mild steel tubes for top and bottom rails, mild steel frame shall be covered with heat moulded plain colour PVC sheet, 'C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail and bottom rail; panelling of plain colour PVC sheet to be fitted in mild steel frame welded/ sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement, complete, all as specified & shown in relevant drawing of item No. 08080 in MES Schedule (Part-II) and directed by Engineer-in-Charge.

S&F 200 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified and directed by Engineer-in-charge.

S&F as in repair 150 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified and directed by Engineer-in-charge.

S&F 200 mm long mild steel barrel tower bolt stove enamelled black with bright bolt (ISI marked) complete all as specified & directed by Engineer-in-Charge.

S&F 100mm size mild steel butt hinges cold rolled medium weight (ISI marked) complete all as specified & directed by Engineer-in-Charge.

S&F as in repair 100mm size mild steel butt hinges cold rolled medium weight (ISI marked) complete all as specified & directed by Engineer-in-Charge.

S&F 100mm size butt hinges of extruded aluminium alloy with galvanized mild steel hinge pin, anodized type B-21 (ISI marked) complete all as specified and directed by Engineer-in-charge.

S&F 300mm long mild steel sliding door bolts clip type, stove enameled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate (ISI marked) complete all as specified & directed by Engineer-in-Charge.

S&F as in repair 250mm long mild steel sliding door bolts clip type, stove enameled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate (ISI marked) complete all as specified & directed by Engineer-in-Charge.

S&F 125 mm long mild steel pressed handle, oval type, stove enameled black (ISI marked) complete all as specified and directed by Engineer-in-charge.

S&F as in repair 125mm long extruded aluminium handles, anodised, fabricated type (ISI marked) complete all as specified and directed by Engineer-in-Charge

S&F 125mm long extruded aluminium handles, anodised, fabricated type (ISI marked) complete all as specified and directed by Engineer-in-Charge

S&F as in repair floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring overall length of cover plate 140mm (ISI marked) complete all as specified and directed by Engineer-in-Charge.

Supply only as in repair aluminium (Die cast) body door closer hydraulically regulated, designation No. 3 universal type, suitable for door shutters of 851 to 1000mm in width and weight between 61 to 80kg (ISI marked) complete all as specified and directed by Engineer-in-Charge.

Supply only as in repair double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made out of mild steel heavy duty & fixed (ISI marked) complete all as specified and directed by Engineer-in-Charge.

S&F as in repair door seal rubber strip fixed with aluminium frame at door bottom for gap 2-30mm complete all specified

S&F galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staple complete all as specified and directed by Engineer-in-charge.

S&F as in repair galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staple complete all as specified and directed by Engineer-in-charge.

S&F as in repair bright finished brass 100mm mortice slatch and lock with four levers and pair of anodized (anodic coating 10 mircron) as per IS-1868 aluminium lever handles with necessary screws etc complete all as specified and directed by Engineer-in-charge.

S&F as in repairs powder coated mild steel drapery rod of 20 mm inner dia (in lengths as directed) of approved colour with & including decorative finial at both ends and pair of powder coated mild steel brackets fixed at both ends with PVC rawl plug & steel screws on walls/beam, including PVC curtain rings of matching colour @ 10cm C/C all as specified & as directed.

S&F as in repair Mild Steel 300mm, ordinary rat tail rod patttern springs including roller & roller plate fixed to wooden frame or welded to steel frame making suitable cut out in wall and making good in CM 1:4 complete all as specified and directed by Engineer-in-charge.

S&F mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, cooler stand 12mm sq guard bar, framework of water tanks and similar works of quality Fe 290 (Gde E-165) etc complete all as specified and directed by Engineer-in-charge.

S&F as in repair mild steel handle of required shape and size including nut, bolts and washers (right or left handles of steel windows) complete all as specified and directed by Engineer-in-Charge.

M&L for aluminium grill mesh made out of 10mm dia having girth not exc 75mm both ways fixed with aluminium cleat to window frame complete all as specified and directed by Engineer-in-Charge.

S&F anodised aluminium doors shutters powder coated (thickness of powder coating shall not less than 50 micron) sliding / openable having aluminium sections weighting 0.55 Kg/RM including necessary jointing cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, 100mm size, 4 levers brass mortice lock vertical type (01 No), hinges, anodised aluminium snap beading, screws complete all as specified and directed by Engineer-in-Charge.

Easing of window shutters, kitchen cupboard shutters, show case shutter drawers including teakwood lipping, fixing of screws adjusting handles, knobs tightening piano hinges, beading fittings including misc small adjustments complete all as specified and directed by Engineer-in-charge.

S&F Anodised aluminium snap grid frame work of size 605mm x 605mm for false ceiling including necessary notching. The snap grid shall consist of anodized aluminium main & cross Tee of size 36.5mm x 25mm x 1.4mm weighing 0.24 Kg/RM and 23.5mm x 26.4mm x1.40mm weighing 0.191Kg/RM respectively. The main and cross tee shall be jointed at junction crossing with anodized aluminium angle bracket of size 15mm x 15mm x 1.5mm weighing 0.12Kg /RM fixed with suitable MS bolts, nuts and washer. The snap grid (main /cross tee section) shall be supported at ends all along the wall with anodized aluminium angle of size 35mm x 25mm x 2mm weighing 0.36 Kg/RM fixed to wall with suitable arrangement duly suspended with 3mm dia GI wire length as required @ 600mm C/C with adjustable device including plugging in brick / concrete work with steel raw plugs including making good all the disturebed portion complete all as specified and directed by Engineer-in-Charge.

M&L for 4mm thick E board classic, fibre base cement boards, embosed texture, fixed to aluminium snap grid (size of grid 605mm x 605mm) in ceiling complete all as specified and directed by Engineer-in-charge. Note :- The aluminium snap grid frame work shall be measured & paid for separately.

M&L for running welding as in repairs not exc 2.5cm in length, thickness of metal to be welded not exceeding 6mm complete all as specified and directed by Engineer-in-charge.

M&L for preparation of new wooden or wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-charge.

Hacking out old broken glass any thickness, size, quality or description from wooden / metal frame and punching or drilling out old glazing pins/spring clips complete all as specified and directed by Engineer-in-charge.

M&L for securing of old glass of any description in existing metal frame glazed with putty / beads including removing loose or decayed putty, beads painting / oiling one coat on rebates, groves reputting and painting / oiling puttied surface to match existing work (New length of frame reputtied shall be measured complete all as specified and directed by Engineer-in-charge.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces, complete all as specified and as directed.

S&F 4mm thick figured glass pin head type and glazing with oil putty in square not exc 0.5 sqm in each pane complete all as specified and directed by Engineer-in-charge.

S&F 5.5mm thick sheet glass ordianary quality glazing with oil putty in squares, area exceeding 0.50 Sqm in each pane area complete all as specified and directed by Engineer-in-Charge .

Taking up or down 15mm dia, steel tubing & connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-Charge.

S&F 15mm bore galvanized steel water tubing medium grade with & including all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed by Engineer-in-charge.

Fixing only 15mm bore old galvanised steel water tubing including cleaning with & including new fittings and fixed complete to walls and ceilings or laid in floors in new or old position complete all as specified and directed by Engineer-in-charge. Note :-GI tubing retrieved vide item No 49 shall be used under this item

Taking up or down 20mm dia, steel tubing & connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-Charge.

S&F 20 mm bore galvanized steel water tubing medium grade with & including all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed by Engineer-in-charge.

Fixing only 20mm bore old galvanised steel water tubing including cleaning with & including new fittings and fixed complete to walls and ceilings or laid in floors in new or old position complete all as specified and directed by Engineer-in-charge. Note :-GI tubing retrieved vide item No 52 shall be used under this item

S&F as in repair small fittings of galvanised iron medium grade such as socket / elbow / nipple of different sizes / Tee / union / reducer etc for 15mm bore pipe complete all as specified and directed by Engineer-in-charge.

S&F as in repair small fittings of galvanised iron medium grade such as socket / elbow / nipple of different sizes / Tee / union / reducer etc for 20mm bore pipe complete all as specified and directed by Engineer-in-charge.

S&F as in repair 15mm bore brass chromium plated shower rose with or without swivel joints, any size, including fixing to steel pipe or union with shower arm 15mm size, 195mm long iwht bend of 45 degree with flange complete all as specified and directed by Engineer-in-charge.

S&F as in repair 450mm long PVC connection suitable for 15 mm bore with PTMT nuts on both sides complete all as specified and directed by Engineer-in-charge.

S&F as in repair chromium plated towel ring round with round flange 200mm dia including chromium plated brass screws and plastic cleats complete all as specified & directed by Engineer-in-Charge.

S&F as in repair brass chromium plated tubular towel rail 20mm dia; 'D' type, 600mm long between flanges fixed to plug with chromium plated brass screws including wooden or plastic cleat complete all as specified and directed by Engineer-in-Charge.

S&F as in repair health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S&F as in repair grating doom 125mm dia of PTMT with waste hole (minimum weight 40 grams) complete all as specified and directed by Engineer-in-Charge.

S&F as in repair 20mm brass tank nipple complete all as specified and directed by Engineer-in-Charge.

S&F as in repair 25mm brass tank nipple complete all as specified and directed by Engineer-in-Charge.

S&F in replacement HDPE PVC lid (cover) for 500 Ltr capacity water storage tank complete all as specified and directed by Engineer-in-Charge.

S&F in replacement HDPE PVC lid (cover) for 1000 Ltr capacity water storage tank complete all as specified and directed by Engineer-in-Charge.

S&F as in repair rotational moulded polyethylene water storage tank ISI Marked (cylindrical vertical three layered with closed top) hoisted and fixed in position of capacity 500 litres including ball brass valve, high pressure with polythene float and flynut screwed for 20 mm dia GI pipe, 25mm bore GI washout pipe 15 cm long fitted with check nut, 20mm bore over flow pipe 1.50 metre long fitted with brass anti-mosquito nest coupling at the end of over flow pipe & 15mm bore GI air vent pipe 1.30 metre long fitted with tee at the end of air vent pipe (All GI pipes shall be medium grade) complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 67 here-in-before but 1000 ltrs capacity

S&F as in repair 15 mm bore bib tap, cast copper alloy, chromium plated, long body, fancy type screwed down and screwed for iron pipe or for brass ferrule complete all as specified and directed by Engineer-in-charge.

S&F as in repair 15mm bore PTMT bib tap of any colour high pressure, screwed for iron pipe (minimum weight 90 grams) complete all as specified and directed by Engineer-in-charge.

S&F as in repair fancy type pillar tap, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks & fly nuts, screwed suitable for iron pipes of 15mm bore complete all as specified and directed by Engineer-in-charge.

S&F as in repair brass spindle for bib tap complete all as specified and directed by Engineer-in-Charge.

S&F in replacement Ball valves, high pressure of PTMT with epoxy coated aluminum rod & high density plastic ball, screwed for iron pipe 20mm dia (minimum weight 210 gms) complete all as specified and as directed by Engineer-in-charge.

S&F in replacement Ball valves, high pressure of PTMT with epoxy coated aluminum rod & high density plastic ball, screwed for iron pipe 25mm dia (minimum weight 210 gms) complete all as specified and as directed by Engineer-in-charge.

S&F as in repair 15mm bore angle valve, cast copper alloy, chromium plated, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed by Engineer-in-charge.

S&F 15mm bore PTMT stop valve of any colour high pressure, screwed for iron pipe (minimum weight 90 grams) complete all as specified and directed by Engineer-in-charge.

S&F 20mm bore PTMT stop valve of any colour high pressure, screwed for iron pipe (minimum weight 90 grams) complete all as specified and directed by Engineer-in-charge.

S&F as in repairs 15mm bore brass chromium plated basin mixer for mixing hot & cold water screwed down for iron pipe of 15mm bore complete all as specified and directed by Engineer-in-charge.

S&F as in repairs 15mm bore brass chromium plated wall mixer for mixing hot & cold water screwed down for iron pipe of 15mm bore complete all as specified and directed by Engineer-in-charge.

S&F as in repair toilet paper holder of vitreous china fixed to walls with chromium plated (CP) brass screws complete all as specified & directed by Engineer-in-Charge.

Petty repairs to leaking water in bib taps, pillar taps, stop cocks, angle valves, float valve, concealed stop cock, GI pipe joints, bottle traps etc of any description by changing the washers, disc etc or any other minor accessories to make the system functional complete all as specified and directed by Engineer-in-charge.

Petty repairs to leaking water in bib taps, pillar taps, stop cocks, angle valves, wall mixtures, wash basin and sink mixtures, concealed stop cocks etc of any description by changing the spindle or any other minor accessories to make the system functional complete all as specified and directed by Engineer-in-charge.

S&F as in repair vitreous china wash basin white, flat back of size 550x400mm including including a pair of cast iron brackets embedded in PCC 1:3:6 type C-1 blocks of size 10 x 7.5 x15 cm with & including 32 mm dia PVC waste pipe, 32mm dia PTMT waste coupling half or full thread (minimum wt 45 grms) flange end bedded in red lead cement & other end fixed to waste pipe and including brass chromium plated fancy type pillar tap, screwed suitable for iron pipes of 15mm bore complete all as specified and directed by Engineer-in-Charge.

S&F as in repair 10 litre capacity PVC valveless symphonic action type low level flushing cistern (ISI marked) including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified and directed by Engineer-in-charge.

S&F as in repairs plastic water closet seat, white, closet pattern with flat bottom and cover and mild steel chromoum plated or aluminised hinging device complete all as specified and directed by Engineer-in-Charge.

Petty repairs to high / low level flushing cistern by adjusting the float valve, leakage PVC connection, PVC / GI bend including replacing of L bend, rubber washer check nuts plunges etc for any type of flush complete all as specified and directed by Engineer-in-charge.

S&F as in repair Waste coupling of PTMT (half or full threaded) 32mm bore dia discharge pipe (Minimum weight 45 gms) complete all as specified and directed by Engineer-in-charge.

S&F as in repair Waste coupling of PTMT (half or full threaded) 40mm bore dia discharge pipe (Minimum weight 45 gms) complete all as specified and directed by Engineer-in-charge.

S&F as in repair PVC cabinet with mirror of size 450x600mm complete all as specified & directed by Engineer-in-Charge.

S&F as in repairs PVC waste pipe 32 to 40mm bore suitable for WHB or Sink complete all as specified and directed by Engineer-in-charge.

S&F as in repair sink with drainage board made of stainless steel 1mm thick for kitchen with plugs, washers and wastes, overall size 915mm x 460 mm / (36" x 18") bowl size 410mm x 355mm / (16" x 14") and depth 175mm / (7") including waste pipe of polythelene of low or high density or PVC 32mm dia & waste fitting brass chromium plated 32mm bore with long screwed shanks and fly nuts including making holes in brick walls for brackets and fixed in CM (1:3) or PCC 1:2:4 type B0 complete all as specified and directed by Engineer-in-charge. Make :- Nirali model Elegance (Glossy) / Prayag model No 1128-D Gold Series (Gloss) / Silver Shine (Bluestar sanitary industries Pvt Ltd) model No SSSB-52 (Glossy) or equivalent in makes mentioned in Appendix 'A' here-in-after. Note :- Size of sink for different mafufacturer may slightly varried from size mentioned in description of item. Contractor has to provide sink as per cat No mentioned against make of sink. where cat No is not mentioned against any make, in that case sink of size mentioned in description has to provide, if exact size of sink is not available, then next higher size sink has to be provided. Nothing extra shall be paid on this account.

S&F as in repair stainless steel plate rack of size 750mm x 600mm x 254mm made out of 0.63mm thick stainless steel of first quality complete all as specified and directed by Engineer-in-Charge. Make: Silver Shine (Blue Star sanitary industries Pvt Ltd) Model No KPR 313 / Prayag model No P-340 / Blue Star (Anupam Industries) model No KPR-313 or equivalent in makes mentioned in Appendix 'A' here-in-after.

S&F as in repair jet spray chromium plated brass for ewc with & including PVC connection 600mm long suitable for 15mm bore GI pipe complete all as specified & directed by Engineer-in-Charge.

Taking down existing aluminium door frame including glazed shutter & builders hardware complete of area 1 sqm and not exc 2 sqm each of any description and refixing in the same opening after carying out necessary repair & replacement of unserviceable components / hardware to make if fully functional complete all as specified and directed by Engineer-in-charge. Note :- (i) Cost of new jointing cleat, aluminium beading, glazing clips, rubber packing stays including cutting of old style etc and adjusting the same appropriately deemed to included to in the unit rate of this items nothing extra shall be paid on this account. (ii) Glazing, new aluminium section for frame / shutter, builders hardware such as handles hinges door closure, floor door spring shall be measured & paid for seprately. (iii) Loose corner joints of frame & shutter shall be tightned by providing shuitable cleats made out of aluminium angle of appropriate size fixed with nut & bolts to make joints at 90 degree.

Taking down carefully or drawn out from conduit, existing copper / aluminium point wiring for light, fan, bell, socket, power point etc complete including fixture and fittings such as switches, sockets, ceiling rose, pendent holder, light fittings, top sheet covers, fan regulators, MCB, DB, lamp, earth plug etc (excluding MS sunken boxes) and making good the disturbed surfaces of wall/ceiling complete all as specified and as directed by Engineer-in-charge. Note : Taking down of serviceable fittings shall be measured and paid separately.

M&L for point wiring complete with 1.5 sqmm (nominal cross sectional area) FRLSH PVC insulated multistandard unsheathed copper conductor cable with colour coding drawn in and including new PVC rigid conduit medium grade 20mm dia and suitable fittings, fixed on surface of wall or concealed or above ceiling with accessories such as pipe hooks, elbows, junction box, terminated in new sunken box and covered with new 3mm thick bakelite plastic laminated sheet top cover fixed flush with wall using brass screws & cup washers including cutting chases in wall for conduits and making good the disturbed surfaces of wall and including 1.5 sqmm PVC insulated unsheathed multistandard copper conductor wire as earth continuity to common earth and connecting to earth dolly for one light point, fan point controlled by one way switch complete all as specified and directed by Engineer-in- charge.

All as per serial item No. 97 here-in-before but for One 3 pin 5 Amp socket outlet one light point controlled by one switch on the same board with other switches.

All as per serial item No. 97 here-in-before but for One 3 pin 5 Amp socket outlet one light point controlled by one switch on independent board.

All as per serial item No. 97 here-in-before but for One bell or buzzer point controlled by by one push button on independent board.

All as per Srl item No. 97 above, but wiring with cable of cross sectional area 2.5 Sqmm (nominal area) multi-stranded copper conductor FRLSH, PVC sheathed cable 1100 Volts shade for one switch socket combination 6 pin, 5/15 Amps on independent board including 2.5 Sqmm PVC insulated multistranded unsheathed copper conductor wire as earth continuity to common earth dolly.

S&F switch piano flush button 5 Amps single pole, one way complete all as specified and directed by Engineer-in-charge.

S&F switch piano flush button 15 Amps single pole, one way complete all as specified and directed by Engineer-in-charge.

S&F socket outlet 3/5 pin, 5 Amps 240 volts, flush type complete all as specified and directed by Engineer-in-charge.

S&F socket outlet 3/5 pin, 15 Amps 240 volts, flush type complete all as specified and directed by Engineer-in-charge.

S&F bell push, flush type, 5 Amp, 230 Volts grade complete all as specified and directed by Engineer-in-charge.

S&F Lamp holder, insulated body with back plate etc complete all as specified and as directed by Engineer-in-Charge.

S&F ceiling rose surface bakelite 65mmx50mm with two or three terminal complete all as specified and directed by Engineer-in-charge.

S&F electric bell (ding - dong), AC, 230 Volts, Single pole & connecting up complete all as specified and directed by Engineer-in-charge.

S&F electronic fan regulator suitable for ceiling fan 1200mm/1400mm sweep, socket size, rotary type complete all as specified and directed by Engineer-in-charge.

S&F as in repair Energy efficient decorative ultra slim, prewired, Maxoled batten for T-8 LED retro lamp, polycarbonate body, 1.2m length, ultra bright, glass shell, glare free, wide angle single/ double side connection retrofit LED tube with G-13 lamp holder/patti 20 watt LED light fitting (Day cool light) including 20 watt LED tube with all accessories prewired fixed on wall / hanging complete all as specified and as directed by Engineer-in-charge. Make :- Havells Cat part No LHFXCENNTN1W020 & LHLDDCXCML8Q020 / Crompton cat part No DIJB12LT8-20 & LGT8-16-865-2 or equivalent cat part No of makes mentioned in Appendix 'A' here-in-after.

S&F as in repair MCB 6 to 32 Amps, Single Pole 240 Volts, 10 KA, ‘C’ Curve, complete all as specified and directed by Engineer-in-charge.

S&F in replacement MCB 63 Amps, Single Pole & neutral 240 Volts, 10 KA, ‘C’ Curve, complete all as specified and directed by Engineer-in-charge.

Supply and fixing in replacement LED lamp minimum 3 star rated 10W LED B-22 base complete all as specified and directed by Engr-in-Charge with following specifications (a) Lumen system efficacy of lamp should be minimum 100 Lumen per watt. (b) Input Voltage range : 140 to 270 volts (c) Temp operating range : Minus 10°C to Plus 45°C (d) Power factor : Minimum 0.90 (e) CRI : Morethan 80

S&F in replacement sheet metal plug & socket DB, SP, with a two pin and earth plug with socket, 230 Volts with & including one MCB SP ‘C’ Curve 10 kA, 20 Amps complete all as specified and directed by Engineer-in-charge.

S&F as in replacement Energy efficient decorative ultra slim prewired 9 / 10watt (600mm length) LED light fitting (Mirror light) (Day cool light), surface and wall mounted LED batten, extruded aluminium housing with polycarbonate diffuser & integrated electronic driver and all accessories fixed on wall / hanging complete all as specified and as directed by Engineer-in-charge. Make :- Havells Cat part No LUMILINEBS9WLED865 SPCWH / Syska cat part No SSK-T5T-9W / Crompton cat part No LCTLN-10-CDL or equivalent in makes mentioned in Appendix 'A' here-in-after.

S&F as in replacement Energy saving 9/10 watt environmental friendly, ultra modern, energy saving, surface mounted, decorative oval bulk head edge-lit LED luminaire comprising of high brightness LEDs, IP 65 protection fixed on wall complete all as specified and as directed by Engineer-in-charge. Make :- Havells Cat part No HEXAFT10WLED857SSY MBOPC / Syska Cat part No SSK-BH-9W / Crompton cat part No LBHE-10-CDL or equivalent in makes mentioned in Appendix 'A' here-in-after.

Supply, fixing and testing as in replacement LED Bldg / Security light fitting of 25 Watt, 5700K - 6500 K (including LED drive and internally prewired) complete with body robust, corrosion resistant, superior finish and without any cracks or through holes, made in a single piece by high pressure die cast aluminum alloy. The luminaries shall be monolithic construction totally enclosed dust and water proof with IP -65 / 66 protection as per IS - 10322-1982(Part -I) with latest amendments and input voltage range 140 - 300 V, AC, frequency 50 - 60 Hz ,P.F should be more than 0.9 with Total Harmonic Distortion THD(I) less than 15%, cool white colour and lamp starting time should not be more than 10 second including 10 KV surge protection in built or external. Driver should be constant current constant voltage driver. Driver should have high voltage withstanding capacity upto 300 V, AC. Driver should also have double phase protection, no load , open circuit and short circuit protection .LED light fitting should be suitable for ambient temperature from -10 degree Centigrade to 50 degree Centigrade and humidity level 10% to 90 % RH. Covers should be polycarbonate/toughened glass to ensure minimum IP 65 degree protection. Cover should not degrade due to heating and ageing. The efficiency of LED luminaries system shall be more than 100 lumens per watt and must be certified by the LM-79 test report and including connection for street light from pole box with 1.5 Sqmm, 3 core PVC insulated stranded copper conductor FRLSH cable, 1100 Volts grade ISI marked including addition / alteration in bracket (if required) for fixing light fitting complete all as specified and directed by Engineer-in- charge.

Notes for srl Item No 118 :- (a) Tenderer shall submit test report of LED street light fitting from Government accredited test laboratory for LM - 79 and LM - 80 . (b) Contractor has to furnish a replacement warranty of 05 years for LED light fittings complete including lamps from the date of completion of CA. Contractor shall obtain warranty from the manufacturer of product on their letter head and submit the same to deparment alonwith his letter head. The product will be replaced free of cost in the following case :- (i) Manfacturing defects (ii) Failure due to mechanical and electrical impact. (iii) Drop in lumen (or lux at 1 m) below 90% of clamied values of lumen(or lux at 1 m) of the LED /Luminaries. (c) All LED light/luminare must meet the provision laid down in IS - 16101 , 16102 Part -I/II ,16103 Part -I , 16104 ,16105 ,16106 , 16108/2012 and 15885 Part -II / Section 13. (d) Scope of work shall include supply and fixing street light fittings on street light bracket fixed on poles, If street light fitting requires to fixed on existing street light bracket and any addition alterration required in bracket for fixing street light, In that case cost of additional / alteration is included in the unit rate of this item, which also includes needful T & P and required accessories such as 1.5 sqmm, 3 core PVC insulated stranded copper conductor cable for connection from pole box to light fitting etc complete including making connection, testing etc complete .No extra payment is admissible on this account. (e) Light fittings shall be provided with 10 KV surge protection as mentioned in description of item. If 10 KV surge protection is not provided in light fitting for which cat part is mentioned in BOQ. Contractor has to provide light fitting with 10 KV surge protection without any extra cost to department. (f) Contractor shall write CA No on street light fitting with synthetic enamel paint which should be visible from ground level. Cost of the same is included in the unit rate of this item nothing shall be extra paid on this account.

S&F as in repair flush mounting factory made SPN DB 8 way, 240 Volt, Single door, IP-43 protection, IK-09 with metal door with 100 Amps copper bus bar, with neutral bar, earth bar and cables ties for cable management fully insulated bus bar complete all as specified and directed by Engineer-in-charge. ---------------------------------------------------------------------------- Note :- A sum of Rs. 215975/- will be deducted on account of credit for dismantled/ demolished / taken down material. Please refer details on Srl Page No. 24 to 26 (Schedule of Credit) of Tender documents.

DIKSHA ENTERPRISES

SHIVA BUILDERS

BANSAL BROTHERS

S.K BUILDERS AND ENGINEERS

BISHNOI BUILDERS

HARPREET SINGH CONTRACTOR

M/S Shree Ram Enterprises

AK CONSTRUCTION