ADDN/ALTN TO BLDG NO P-74, P-98, P-99, P-100, P-101, P-106, P-67, P-69, E-43 (120 QTRS) OF KABUL LINE IN THE AREA OF AGE B/R-II UNDER GE(EAST) DELHI CANTT-10

Amount

Demolition of cement concrete (reinforced) of any position not otherwise specifically provided for and including reinforcement required to facilitate demolition upto and including fourth story and on the roof top/mumty/parapet and removal of debris and rubbish out side MoD land complete all as specified and directed.

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in Ground floors and paving n.exe 15cm thickness ( below or above ground level ) including removal of rubbish out side complex (MOD land), complete all as specified and directed.

Dismantling of PVC water tanks of exc 250 litres and n.exc 500 litres capacity of any condition or type complete all as specified and directed.

Dismantling of Cast Iron or reinforced concrete pipe of internal dia 100 mm jointed in cement mortar and taking out of trenches if required complete all as specified and directed.

Taking down steel window and ventilator complete all as specified and directed.

Dismantling of Brick tiles or terracing tiles, single layer on roofs, kerbs, aprons, etc. (each layer) complete all as specified and directed.(Note : All roots of plant on either on wall or roof to be removed and making good the disturbed surfaces. The rate quoted by the contractor is deemed to be included in the unit rates.)

Demolition of Mud phuska in roofs, any thickness including plastering and leeping of any thikness upto 30cm deep complete all as specified and directed.(Note : All roots of plant on either on wall or roof to be removed and making good the disturbed surfaces. The rate quoted be the contractor is deemed to be included in the unit rates including the removal of mud phuska outside defence land.)

Dismantling of floor of WC with Indian type Water closet and removing out the cinder/concrete from sunken protion, cleaning of RCC surface to remove dust, loose particle with compressed air or any other suitable method depending on site conditons, grinding any sharp edges etc including following work complete all as specified and directed . (a) Cleaning the RCC surface to remove dust, loose particle etc with compressed air or any other particles or any other suitable techniques on site conditions etc. (b) M&L for a glass fibre reinforced acrylic modified cementitious coating system with base coat of Sika Top & Seal-107 @ 1.50 Kg/Sqm glass fibre reinforcement Sika® Fab-I and top coat with Sika Top® Seal-107 @ 1.50 Kg/Sqm or equivalent of Fosroc or Pidilite. (c) M&L for protection plaster 15mm thick on cement mortar 1:3 admixed with appropriate integral water proofing compound with Sika ® Plastocrete plus as specified. (d) M&L for providing 25mm dia GI pipe spout projecting at least 150mm beyond outer face of wall. (e) M&L for sunken portion filled with 40 mm graded brick bats and finished with 50 mm thick PCC 1:2:4 type B1 all as specified and directed. (f) The area of Each WC portion is n.exc 2.00 Sqm each. (g) Cost of the above aspect shall be deemed to be included in the quoted rates of the respective item and nothing extra shall be paid on this account. Note : The work will be executed by authorised manufacturers/applicator.

Taking up or down 15 mm bore GI tubing and connections including cleaning for re-fixing complete all as specified and directed.

All as per item No. 10 above but 20 mm bore

All as per item No. 10 above but 25 mm bore

Taking down chowkats or frames exc. 1.5 Sqm and n.exc 4 Sqm each with shutters (without taking off shutters from frames) complete all as specified and directed.

Taking down chowkats or frames not exc. 1.5 Sqm each with shutters (without taking off shutters from frames) complete all as specified and directed.

Taking down shutters of any description exc 1 sqm and not exc 2 sqm each complete all as specified and directed.

Taking down cement plaster, terrazzo dado in any thickness from brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc including removal of rubbish,vegetation etc outside complex (MOD land) complete all as specified and directed.

S&F Fiber Glass Reinforced Plastic (FRP) Door Frames of cross section 90mm x 45mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame complete all as specified and directed.

S&F 30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardantgrade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames complete all as specified and directed.

S&F rolled mild steel Framed work as in doors or gates of angle or other section with gusset plates, rails,braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rails and guides) and hanging; also fastening and fixing complete Fe 410 -W (Gde-E- 250) quality-A all as specified and directed.

S&F mild steel framed work such as grills, grating ,Railing ,Gate,,etc with ends of bars shouldered or riveted or forged into spikes framed guard bars and similar work confirming to Fe - 290-0 or E-165 including two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F 35mm thick factory made flush shutters, solid core construction, with block board core and plywood face panels commercial type on both sides complete all as specified and directed.

S&F factory made 2nd class hard wood glazed and skeleton shutter of 35mm thick, open rebated and prepared to receive glass/gauze etc,( without sash bars), mitred and rebated, with edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass/guage etc, sizes of members of shutter as specified in section 8, clause 8.24(a) of SSR Part I complete all as specified and directed.

S&F 25 mm thick flush shutter solid core construction with block board core and ply wood face panel commerical type on both side to be fixed as shutter of cupboard/kitchen cup board/loft board complete all as specified and directed.

S&F 100 mm long (size) butt hinges, medium weight, cold rolled mild steel, and fixed, complete all as specified and directed.

S&F 75 mm long (size) butt hinges, medium weight, cold rolled mild steel, and fixed, complete all as specified and directed.

S&F in repair Aluminium anodised,barrel tower bolts of extruded section 200 mm long, extruded section complete all as specified and directed.

S&F Aluminium anodised,barrel tower bolts of extruded section 200 mm long, extruded sections complete all as specified and directed.

S&F Extruded aluminium alloy handles, fabricated type,anodised 150mm size long complete all as specified and directed.

S&F in repair Extruded aluminium alloy handles, fabricated type,anodised 150mm size long complete all as specified and directed.

S&F of Floor door stopper of aluminium alloy body and tongue, anodised,with hard drawn steel spring,fixed in floor 140mm long complete all as specified and directed.

S&F in repair Floor door stopper of aluminium alloy body and tongue, anodised,with hard drawn steel spring,fixed in floor 140mm long complete all as specified and directed.

S&F 300mm long, aluminium anodized sliding door bolts with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified.

S&F in repair 300mm long, aluminium anodized sliding door bolts with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified.

M&L Cement concrete 1:2:4 type B1(using 20mm graded crushed stone aggregate) as in bed blocks for hold fast, coping, benching etc. including weathering, slightly rounded or chamfered angles or throating including form work to concrete surfaces complete all as specified and directed upto two storey height.

S&F Hasp and staple, 75mm size, safety type, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws complete all as specified and directed

S&F in repair Hasp and staple, 75mm size, safety type, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed , complete all as specified and directed

S&F 150mm size double action spring, hinge, mild steel with steel wire spring, stove enamelled black, complete all as specified and directed.

S&F Continuous piano hinges stainless steel of AISI 304 grade width of flaps (when open) 30mm complete all as specified and directed.

M&L Preparation of new or previously untreated wood and wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L preparing old wood surfaces of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint complete all as specified and directed .

Dismantling wrought iron or mild steel work of any description not otherwise provided for all as specified and directed.

M&L Granite of 18 to 20mm thick with uniform texture (table rubbed and polished) in steps, jambs, pillars, window cills,cooking platforms and like in cement mortar (1:4) including pointing with white cement (1:2) using marble dust with admixture of pigment to match with marble shade of makrana doogri green colour stone for Kitchen cooking platform laid over and including 15mm thick screed bed in cement mortar (1:6) polishing bevelled edges of corner etc complete all as specified and directed.

All as per serial item no 42 above but on vetical surfaces including 15 mm thick rendering in cement mortar 1:4 complete all as specified and directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with steel wire staples, complete all as specified and directed

S&F in repair Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with steel wire staples, complete all as specified and directed

M&L for Brick work with sub class B bricks of old size, straight or curved on plan exc 6 m mean radius, built in cement mortar 1:6 complete all as specified and directed.

M&L for Brick work with sub class 'B' bricks straight or curved on plan to any radius in half brick thick wall built in CM 1:4 complete all as specified and directed.

S&F Mild steel TMT bars of 10 mm dia and over cut to length bent to shape required including cranking, bending etc and for stengthening existing reinforcement by use of mild steel bars of any dia , cut to length, bent to shape required, including cranking, bending spirally and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for providing reinforced cement concrete (nominal mix) (1:2:4) type B-1 using 20 mm graded crushed stone aggregate as in kitchen slab, Chajjas, lintels complete all as specified and directed.

M& L for Formwork to chajjas, chullah hoods,kitchen slab and similar items ,including edges complete all as specified and directed.

M&L Machine cut Kota stone slab 20-25 mm thick with uniform texture in floor with laid over and including 15 mm thick screed in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L kota stone slab with uniform texture of 20-25 mm thick in treader of steps, riser of steps, skirting, dado and pillars in one single piece (size decided by Engineer-in-Charge) laid over and including cement screed 15mm thick in cement morter 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing , bevelled edge of corner etc complete all as specified and directed.

M&L Non skid Coloured ceramic rectified tile 400x400x7-8 mm thick as in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L Coloured ceramic rectified tiles 350x450 x 7 to 8mm thick, as in vertical surfaces of wall such as dado/skirting, set and jointed in neat cement slurry and pointed in white or coloured cement over and including 10mm thick rendering in CM 1:4 complete all as specified.

M&L for Vitrified tiles (Double charge) of approved Shade 10mm thick (square/rectangular) polished, area of each tiles exc 0.42 Sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6 complete all as specified.

M&L Coloured glazed ceramic rectified tiles 600 mm x 600 mm x 10 mm thick as in skirting, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 complete all as specified and directed.

S&F 15mm bore GI tubing medium grade with all fittings and fixed to wall and ceiling or laid in floors etc complete all as specified and directed.Note :-The pipe shall be painted with bituminous paint of approved quality and the pipes should not come in contact with lime mortar or lime concrete as pipes are affected by lime etc.

All as per item No 58 above but 20 mm bore.

All as per item No 58 above but 25 mm bore.

S&F white colour Rotational moulded polyethylene water storage tank 500 litres capacity, ISI marked triple layer construction (cylindrical vertical closed top), hoisted & fixed in position including all fittings complete all as specified and as directed.

S&F in repair viterous china squatting pan 'ORISSA Pattern' size 580x440mm white with integral foot rests incl P or S Trap) (excluding flushing cistern & flush pipe) complete all as specificed and directed.

S&F in repairs vitreous chinaware wash down water closet pan padestal pattern white excluding fixing bolts but including jointing to flushing cistern and flush pipe antisyphonage pipe etc, including necessary fittings, 'P'/'S' traps, health faucet, jet spray as required complete all as specified and directed.

S&F vitreous chinaware white colour oval shape wash hand basin (WHB) size 550mm x 400mm complete, Ist quality, including provision of pair of mild steel angle iron brackets of suitable size duly painted and cutting for and pinning in ends of brackets in walls & making good including pedastal & including providing and fixing of suitable waste pipe and waste fitting complete all as specified and directed.

Supply and fixing in repairs PVC valve less syphonic action type flushing cistern 10 ltr capacity, low level, white with inlet, ball valve, float and handle including brackets and connection to pipes and fixing of chain and pull or lever if any complete all as specified and directed.

S & F Brass CP basin mixer for mixing hot & cold water screwed down for iron pipe 15 mm bore, screwed down high pressure, screwed for iron pipe and fixed complete all as specified and directed.

S&F sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed.

S&F stainless steel sink AISI 316 grade with drainage board of 1 mm thick kitchen or laboratory with plug , washer and waste,including bedding in cement morter to dwarf wall or including CP Waste , PVC Down pipe etc and fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm compete all as specified and directed.

S&F stainless steel kitchen plate rack 1 mm thick consisting four shelves made out of stainless steel sheets 1 mm thick over all size 0.90x0.90x0.25m complete all as specificed and directed.

S&F Chromium plated tubular towel rail, 20mm dia, ‘D’ type 60cm long between flanges of brass chromium plated and fixed with brass screws all as specified and dirtected .

S&F stainless steel peg set of six complete all as specified and directed fixed in repair.

S&F 15 mm bore Angle valve cast copper alloy Chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe complete all as specified and directed .

S&F in repairs 15 mm bore Angle valve cast copper alloy Chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe complete all as specified and directed .

S&F wall mixture 15 mm bore cast copper alloy Chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe complete all as specified and directed.

S&F in repairs 15mm bore bib taps standard of Chromium plated high pressure screwed for iron pipe and fixed etc. complete all as specified and directed.

S&F in repairs CP brass shower rose 125mm dia with chromium plated arm fixed to 15mm pipe of revolving type complete all as specified and directed.

S&F in repair CP grating 100mm dia round hole/without hole fix on floor/ nahani trap fixed with cement paste, complete all as specified and directed.

S&F in repair Gun-metal globe or gate valves 20mm bore with iron wheel head, screwed both ends for iron iron complete all as specified and directed.

S&F 15 mm dia Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule , plastic ball screwed for iron pipe and fixed complete all as specified and directed.

S&F in repair PVC connection 15 mm bore and 45cm long with washers complete all as specified and directed.

M&L Preparation of new or previously untreated steel surfaces of any description over 10cm in width or girth,not otherwise specifically and applying two coats of synthetic enamel paint over a coat of redoxide primer complete all as specified .

M&L Preparation of old steel surfaces of any description over 10cm in width or girth,not otherwise specifically and applying two coats of synthetic enamel paint complete all as specified .

S & F 100mm dia (bore of pipe) cast iron (sand cast) soil, waste, vent pipe in any length with or without ears with cement joint fixed to walls, complete all as specified.

S & F 75 mm dia (bore of pipe) cast iron (sand cast) soil, waste, vent pipe in any length with or without ears with cement joint fixed to walls, complete all as specified.

S & F 50 mm dia (bore of pipe) cast iron (sand cast) soil, waste, vent pipe in any length with or without ears with cement joint fixed to walls, complete all as specified.

S&F in repair 100mm dia (bore of pipe) cast iron Tee diminishing pieces or tapers (larger bore measured) with cement joints, complete all as specified.

S&F in repair 75 mm dia (bore of pipe) cast iron Tee diminishing pieces or tapers (larger bore measured) with cement joints, complete all as specified.

S & F 75 mm dia (bore of pipe) branch pieces single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches, fitted with oval access door, complete all as specified.

S & F 100 mm dia (bore of pipe) branch pieces single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches, fitted with oval access door, complete all as specified.

S&F in repair cast iron floor trap square type with Cockroch Proofing CP grating with or without hole including provision of jointing to waste pipes in run lead joint dia of outlet 75 mm, complete all as specified.

S&F in repair for 100 mm pipe bore, stack clamps out of 50mmx 5 mm flat iron and 16 mm dia round iron stays including bolts and nuts and securing ends of stays to walls or roof complete all as specified and directed.

S&F in repair 75 mm pipe bore, stack clamps out of 50mmx 5 mm flat iron and 16 mm dia round iron stays including bolts and nuts and securing ends of stays to walls or roof complete all as specified and directed.

M&L for Cutting holes in brick wall built in CM for inserting hold fast and exc half brick but n exc one brick making good dismantled portion in CM (1:3) or cement concrete (1:2:4) type B0 as required complete all as specified and directed.

Supply only liquid water proofing compound complete all as specified and directed.

S&F Drappery curtain rods decorative type stainless steel 25mm nominal dia of approved quality (3mm wall thickness) including fixing of two number decorative brackets fixed in brick/concrete wall, Two number of latto on both ends of curtain rods complete all as directed and specified.

M&L for applying a coat of bituminous primer conforming to IS - 3384 @ 0.50 Litres/sqm on prepared surfaces of plaster and applying APP based polymeric membrane with mineral slate finish @ 4.00 Kg/Sqm and minimum 3mm thick reinforced with polyester non woven fabric and sealing joints by torch application complete all as specified and directed. (Make : SikaBit T-130 MG or equivalent in IWL, Bengal bitumen,STP) Note : The work will be executed by authorised manufacturers/applicator

M&L 75mm thick PCC 1:3:6 type C2 using 40mm graded crushed stone aggregates as in plinth protection finished even and fair complete all as specified and directed.

M&L for mild steel work in bands, straps, holdfast, hookand pintle hinges confirming to Fe-290 or Gde E-165complete all as specified

M&L Resecuring or Easing and adjusting , without taking down shutters of doors/windows for easy opening /closing ,tightening of hinges and changing its position or adjustment of tower bolts/sliding bolts etc area not exc 2 sqm each complete all as specified and directed.

M&L Cement concrete 1:2:4 type B0(using 12.5mm graded crushed stone agg) as in roof levelling complete all as specified and directed.

M&L Preparation of plastered surfaces of walls and applying two coats of Oil bound distemper on walls over wall care birla putty of 2 mm thick on newly plastered walls complete all as specified and directed.

M&L Preparation of plastered surfaces of walls and applying two coats of Oil bound distemper on walls including 2mm thick Birla putty on old plastered walls incl complete removal of existing treatment complete all as specified and directed.

M&L Preparation of new plastered surfaces of ceiling and applying two coats of Oil bound distemper over 2 mm thick birla putty complete all as specified and directed.

M&L Preparation of old plastered surfaces of ceiling and applying two coats of Oil bound distemper over 2mm thick birla putty incl complete removal of existing treatment of surfaces complete all as specified and directed.

M&L for preparation of new /old decorated external wall surface by complete removal of existing treatement by mechanised sander of Berger paints or equivalent makes viz Xpress sanding machine having suction vaccum bag or by manual scrapping tools where mechincal removal is not possible and applying a layer of 2 mm thick wall care putty, again sand papering thus making surface smooth and applying two coat of wheather proofing exterior acrylic emulsion paint premium quality on wall surfaces incl complete removal of existing treatment complete all as specified and directed.

M&L Water proofing treatment to surfaces of walls/concrete slabs damaged due to moisture and efflorescence including sunken areas of bathrooms/toilets, in balconies by applying acrylic polymer modified cementitious high performance coating or treatment all as per manufacturer's instructions, complete all as specified and as directed. (Make : SmartCare Damp Block 2K/Dr. Fixit (Note : Minimum 5 Years water proofing warranty for the WPT shall be given by the Manufacturer).

-BLANK-

M&L for Providing & Fixing factory made modular kitchen and cupboard shutter with 18 mm thick one side decorative and other side balancing lamination factory pressed HDHMR Board of action Tesa and equivalent including 2 mm thick PVC edge banding tape with hot glue by edge bending machine etc with auto closing spring loaded hinges (hydraulic) type etc with 8mm thick both sides Preliminated BSB (Both side balancing proper ) HDHMR of Action Tesa and equivalent as per IS:14587:1998 with suitable full threaded steel screws etc on the backing of racks ,drawer,cupboard,kitchen cabinet under kitchen counter etc all complete as per direction of Engineer-in-Charge.

M&L for Providing & Fixing factory made modular kitchen and wardrope with 18mm thick both sides balancing lamination factory made HDHMR of action Tesa and equavalent approved brand for boxes, shelves, rack, almirah, cupboard and drawer etc incl necessary nails,screw etc complete as per direction of Engr-in-Charge.

M&L 10-12 mm thick polymer modified readymix cement based plaster make ultratech (brand name readiplast) or equivalent in ratio of 1:4 on brick or concrete surface etc .on wall finished even and fair without using extra cement all as specified.

S&F for steel ventilator (top hung) fabricated from roll formed sections made of galvanized steel colour coated powder coated (Base steel as per IS-513 D quality galvanized as IS 277 with zinc coating of 120 GSM with total coated thickness of 0.60mm. The coated section shall be with primer coated of primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns or powder coated with pure polyester powder upto 50-60 microns thick with the following specifications :- (a) Main frame 72mm x 55mmx0.58mm. (b) Mullion 72mmx50mm x0.58mm. (c) Glazed /guazed shutter frame 47mmx20.20mmx0.58mm. (d) Glass beads size 12mmx12mmx0.58mm Accessories. Each shutter shall be provided with the following fittings :- (i) Stainless steel pipe of hinges 01 set . (ii) Aluminium powder coated handle-02 Nos . (iii)Glass panes Glazed shutter and fixed glass provided with glass of 5.00mm thick float glass . (iv) Wire Mesh –Stainless steel wire mesh of 0.3 mm nominal dia of wire and average width of aperture 1.40mm. Note: The glazed/Guaged shutter shall be measure once i.e. as per area of opening. No separate payment of separate shutter i.e. glazed and fly proof shall be made. Area of shutter shall be the area of opening. The rate quoted by the contractor is deemed to inclusive of all aspects as specified in Drg No CEDZ/TD/289 sheet 1 R/2 and 2R/2.

S&F for steel windows fabricated from roll formed sections made of galvanized steel colour coated powder coated (Base steel as per IS-513 D quality galvanized as IS 277 with zinc coating of 120 GSM with total coated thickness of 0.60mm. The coated section shall be with primer coated of primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns or powder coated with pure polyester powder upto 50-60microns thick with the following specifications :- (a) Main frame 72mm x 55mmx0.58mm (b) Mullion 72mmx50mm x0.58mm (c) Glazed /guazed shutter frame 47mmx20.20mmx0.58mm (d) Glass beads size 12mmx12mmx0.58mm Accessories. Each shutter shall be provided with the following fittings :- (i) Stainless steel pipe of hinges 01 set (ii) Aluminium powder coated handle-04 Nos . (iii) Glass panes Glazed shutter and fixed glass provided with glass of 5.00mm thick float glass . (iv) Wire Mesh –Stainless steel wire mesh of 0.3 mm nominal dia of wire and average width of aperture 1.40mm. (v)Grills window shall be provided with grill made of 10mm square MS bars welded to 12mmx6mm thick MS plate . Distance between bars should not be more than 12cm c/c. Total grill unit shall be enamel painted and fixed to window frame with screw. Note: The glazed/Guaged shutter including guard bars shall be measure once i.e. as per area of opening. No separate payment of separate shutter i.e. glazed and fly proof and guard bars shall be made. Area of shutter shall be the area of opening. The rate quoted by the contractor is deemed to inclusive of all aspects as specified in Drg No CEDZ/TD/289 sheet 1 R/2 and 2R/2.

M&L for providing and applying high quality acrylic modified resin based texture of finetex Honeycomb sand stone- 3211with anti algae and UV resistance property to be applied as in intermediate finishes in desired pattern @ 43.04 kg/10 sqm to form film of 1 - 1.50 mm thickness after scrapping and properly cleaning the surfaces to remove loose particles from the plaster surfaces and applying coating with premium acrylic smooth exteriorpaints with Silicone additives of required shade by two or more coat @ 1.43 Ltrs/ 10 sqm over and including one coat of premium quatity primer. Complete all as specified and as directed.

M&L for providing and applying high quality acrylic modified resin based texture of Pebbletex bubble silver escapade M - 604 Pattern or other any shade / pattern with anti algae and UV resistance property to be applied as in intermediate finishes in desired pattern @ 43.04 kg/10 sqm to form film of 1 - 1.50 mm thickness after scrapping and properly cleaning the surfaces to remove loose particles from the plaster surfaces and applying coating with premium acrylic smooth exteriorpaints with Silicone additives of required shade by two or more coat @ 1.43 Ltrs/ 10 sqm over and including one coat of premium quatity primer complete all as specified and as directed.

M&L for Cutting chases, pinning in, making good to facing where required and pointing in cement mortar1:3 in brick or stone wall , cutting not exc 10cm girth complete all as specified and as directed.

M&L two coats of Black bituminous paint on GI tubbing (New/old) surfaces of any description not exceeding 10 cm width or girth complete all as spd and directed

S&F 110mm bore PVC (SWR) pipes, single socketed, in any length, with rubber rings fixed to walls or laid in floors/trenches complete all as specified and directed

S&F PVC (SWR) bend bore 110mm any radius provided with access doors complete all as specified and directed.

M&L for Providing & injecting chemical for post construction ATT along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc in a portion with cement mortar 1:2 to match the existing apron complete all as specified and directed.

M & L for Post Construction anti termiteTreatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors all as specified and directed.

S&F stainless Steel (SS-304) work as in tubular pipe such purlins and rafter,balluster for railing work etc fixed with suitable arrangement as required complete all as specified and as directed.

M&L for PCC 1:2:4 type B1 (using 20 mm graded stone agg) as required as in benching, roof kerb, mud stops, plateform for OHT and similar type of work, including weathering, slightly rounded or chamfered angles and throating on top of chajjas, rails, cills etc., complete all as specified and as directed.

M& L for Providing and fixing special water tight centering and shuttering including bolting, strutting, propping etc so as to withstand a pressure of 0.1 Mpa including removal of forms for all locations including beams, columns, slabs, walls, foundations, footings, landings, stairs, balconies etc. complete all as specified and as directed by Engr-in-Charge.

M& L for Providing and fixing temporary engineered steel tubular standard double scaffolding system on the exterior side, maintaining it in a serviceable condition for the required duration as approved and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connection with the building etc with suitable working platforms at required locations with essential safety features for the workmen etc complete as per directions and approval of Engineer-in-charge. Note :-The elevational area of the scaffolding shall be measured for payment purpose.

M& L for Providing and fixing plywood covering panels as per the directions of Engineer-in-Charge with necessary backing framework to shield windows etc. from falling debris and removing and taking away the material after completion of work including making good any incidental damage (s) to the existing building or its finishes etc complete. Note :-The measurements for payment shall be made in terms of the area protected by such covering.

M& L for Providing, erecting, maintaining and removing temporary protective screens made out of woven PVC cloth with all necessary fixing arrangement to ensure that it remains in position for the work duration as required complete all as specified and directed.

M& L for Chipping of unsound/weak concrete material of following thickness from slabs, columns etc. with standard power driven percussion type or pneumatic chisel of standard make as approved by Engineer-in-charge including tapering all edges, making square shoulders of cavities etc complete and disposal of debris up for all lifts and leads complete all as specified and as directed by Engr-in-Charge.

(a) 25 mm average thickness.

(b) 50 mm average thickness

M&L for precast machine pressed cement concrete tile size 250x250x20-25 mm or 300x300x20-25 mm thick conforming to IS 1237 laid over & including 15 mm thick screed bed or bedding layer of cement mortar 1:4 and set jointed with grey cement and no pigment and pointed in neat cement slurry in floors, and cut and polished complete all as specified and directed.

M& L for Cleaning of reinforcement from rust including behind the reinforcing bars to give it a totally rust free finished steel surface by hammering the rebar, using wire brushes, chiseling and using alkaline rust remover of approved make with paint brush and removing loose particles after 24 hrs of its application with wire brush and thoroughly washing with water and allowing it to dry all complete as per direction of Engineer-in-charge.

(a) Bars up to and including 12mm diameter.

(b) Bars above 12mm diameter.

M& L for Introducing new reinforcement bars for structural connections in RCC beams, lintels, columns and slabs including power drilling holes of appropriate diameters in reinforced or plain cement concrete to a minimum depth of 100mm and upto 200mm, fixing the reinforcement in position using epoxy. (Rate shall include cost of labour, T&P for power drilling in concrete, epoxy cartridges, plastic nozzle etc complete including cleaning the drilled holes of loose dust by blowing air. The cost of reinforcement shall be payable separately).

(a) Bars up to and including 12mm diameter.

(b) Bars above 12mm diameter.

M & L for Providing and inserting 10 mm dia 200 mm long mild steel shear key bars of required length and diameter in reinforced/ plain concrete as per drawing and directions of Engineer-in-Charge including power drilling holes of appropriate diameters to a minimum depth of equal to 12 times the diameter of shear key bar/levelling gauge, cleaning the drilled holes of loose dust by blowing, insertion of epoxy from cartridge, placing the shear key bar in position and allowing it to stay undisturbed for 24 hours complete as per direction of Engineer-in-charge. (Note:Rate shall include cost of labour, all materials, T&P for power drilling in concrete, epoxy cartridges, plastic nozzle etc complete including cleaning the drilled holes of loose dust by blowing air).

M & L for Cleaning with wire brush, chisel etc for all height exposed concrete surface of lightly sticking materials including foreign materials, loose concrete/ aggregates, etc. The rates shall include cost of movable scaffolding & working platform (cost of working platform shall not be paid under other item) disposing of all debris up to lead of 50 metres and complete in all respects and as per direction of Engineer-in-charge.

M & L for Supply, mixing and applying bonding coat, including cost of material, on prepared non-metallic surface of parent material as per specifications and directions of Engineer-in-charge complete, SBR polymer @10% of cement weight) modified cementitious bond coat @ 2.2 kg cement per sqm of surface area with its proportion complete all as specified and directed.

M & L for Supply & Applying alkaline passivating & bonding coat of approved adhesive over reinforcement duly approved by Enginner-in-charge with approved epoxy bonding coat as per manufacturer’s specifications including sprinkling silica sand (Nos 10) for:

(a) Bars upto 12 mm diameter.

(b) Bars above 12 mm diameter.

M & L for Providing and placing in position Grade M25 Micro-concrete, which shall be cement based prepacked single component, chloride free, non-shrink, free flow, self compacting, ready to use after mixing water in specified proportion obtained from approved manufacturer as per specification and directions of Engineer-in-charge (Payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding/ tapping with a blunt metal instrument

M & L for provding and laying Reinforced Concrete in position M25 grade of reinforced concrete in beams, slabs, columns upto a floor 5 level including the cost of centering, shuttering, formwork complete all as per direction of Engineer-in-charge

M & L for Reinforcement for R.C.C work including Cutting, bending, binding, straightening and placing in position &/or welding with the existing bars wherever necessary complete all as per direction of Engineer-in-charge

M& L for Providing, mixing and applying Polymer Modified Mortar in layers, each layer not execeeding 12.5mm thick, including trowelling with wooden tools etc. complete as per specifications and directions of Engineer-in-charge For payment purposes, pre-measurment of thickness shall be done just after the surface preparation is completed. (Payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding/tapping with a blunt metal instrument) Cement (75mm size cube crushing strength at the end of 28-day not to be not less than 25 N/sqmm) complete as per direction of Engineer-in-charge

(a) 25 mm average thickness (in 2 layers).

(b) 50 mm average thickness (in 4 layers).

Cleaning the concrete surface by sand blasting with coarse sand followed by and including cleaning with oil free air blast complete all as specified and direction of Engineer-in-charge.

M & L for Providing and fixing reinforcement with hard drawn steel wire fabric of 3 mm dia wire,100 mm pitching fixed to existing RCC slab (bottom face) complete as per direction of Engineer-in-charge

M & L for Shotcreting (Guniting) RCC slab 20 mm thick with approved mix mortar (with ordinary portland cement, coarse sand in proportion (1:3) including the cost of centering and shuttering at edges and corner if required,wet curing etc.complete as directed by Engineer-in Charge.Surface shall be satisfactory evaluated by sounding /tapping with a blue metal instrument.

ROAD PATH

M & L for 75 mm thick Plain cement concrete (1:4:8) Type D-2 using 12.5mm graded stone aggregate as in floors and finished the surface fair to received screed bed all as specified and directed even and smooth without using extra cement

M& L for Sand filling under floors or in foundations including watering and consolidations complete all as specified and directed.

M&L Machine pressed precast concrete interlocking paver block any shape and size conforming to IS 15658-2006 of 80mm thickness M-40 Grade with grey cement and pigment complete all as specified and directed.

SEWAGE DISPOSAL

Excavation in trenches n exc 1.5m wide and n exc 1.50m in depth for foundation etc and getting out in soft/loose soil complete all as specified and directed.

Excavation in trenches exc 1.5m but not exc 3.0 m in depth for soak well deep in any type of soil with all necessary arrangement and safety of other existing structure and getting out complete all as specified and directed by Engr-in Charge.

Returning filling in, including spreading levelling watering and well ramming in layers n exc 25cm thick (after the pipes have been laid and tested) in soft/loose soil complete all as specified and directed

Removing excavated material (soil) not exceeding 50M and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed

M&L for plain cement concrete 1:4:8, Type D-2 using 40mm graded crushed stone aggregate as in foundations, filling and mass concrete, complete all as specified and as directed.

M&L for cement concrete 1:4:8 type D2 (using 40mm graded agg) incl packing under and haunching against the sides for 150mm internal dia DWCPE (SNP) pipes after they are laid and tested complete all as specified (thickness of concrete bed 150mm).

M&L for DWCPE (SN8) nominal size 200 mm (internal dia) including all fixing accessories or fittings like socket/spigot joint with elastomeric sealing ring, rubber ring, SILAID rubber lubricants required for laying of pipes, laid in trenches, complete all as specified and as directed.

M&L Brick work using sub class’B’ bricks in CM ( 1:4) straight or curved on plan exc 6 mtr mean radius complete all as specified.

M&L for rendering 15mm thick in CM 1: 4 on fair faces of brick work or concrete surfaces with water proofing compound finished even and smooth without using extra cement complete all as specified.(Water proofing compound shall be measure and paid separately)

M&L for Cutting into existing manholes for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 or 3/4 section ) in cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate finished smooth and reforming benching as required for 150/200mm dia pipes complete all as specified and directed.

M&L for factory made steel fibre reinforced (SFRC) man hole covers with frame including necessary hold fast/lugs for embedding (medium duty) 560mm dia or rectangular of equivalent area conforming to IS-12592, complete all as specified and as directed.

M&L for PFRC (plastic fibre reinforced concrete) drain medium duty cover of overall size 1000mm x 500mm, 75-80mm thick provided with provision of two lifting hooks at appropriate locations, factory made, complete all as specified and as directed. Make : Polycrete or equivalent in Binayak Hi Tech Engg Pvt Ltd/Everlast Composites/Tribeni Fibre Pvt Ltd.

M&L for providing PCC 1:2:4 type B2 in surface channels and drains (using 20 mm graded crushed stone aggregate ) complete all as specified & directed.

Description of Work / Item(s)

Amount

Taking down/ out carefully copper/aluminium point wiring for light/fan/bell/ sockets 5/15 Amp complete with switches, Sockets, holders, ceiling roses, light fitting regulators etc and making good the disturbed surface of wall/ceiling and matching with the existing surface complete all as specified and as directed.

M&L Point wiring with single core fire retardant low smoke PVC insulated, unsheathed multi stranded copper conductor of size 1.5Sqmm alongwith 1.5Sqmm earth wire of multi strand copper conductor (with same specification) connected to common earth dolly and drawing through existing surface/concealed conduit pipe and in existing MS box covered with existing hylem sheet for mounting switches, sockets or fan regulators etc., complete all as specified and as directed for the following :-

(a) One light/ fan/bell point controlled by one by one way switch.

(b) one 3 pin socket outlet point 5 amps on the same board with other switches.

(c) one 3 pin socket outlet point 5 amps on the independent board.

All as per description of Srl Item No.- 02 here-in-before but wiring with 4.0 Sqmm copper wire and 4.0 Sqmm earth wire for socket out let 6/16 Amps on independent board.

S & F of Switch piano flush type single pole one way ,5/6 Amps complete all as specifed and as directed .

S & F Bell push piano single pole , 5/6 Amps, 240 volts complete all as specifed and as directed .

S & F socket two-in-one 3 pin, 5/6 Amp complete all as specifed and as directed .

S & F Socket outlet 3/5 pin 15 Amp flush type complete all as specifed and as directed .

S & F Switch piano type 15 Amp single pole one way complete all as specifed and as directed .

S & F Ceiling rose, 3 terminal , PVC / Polycarbonate, isolated body all as specified and directed.

S & F lamp holder PVC / Polycarbonate type with back plate suitable for batten fittings etc complete all as specified and directed.

S&F bell DINGDONG type, 6 Amps, 240 volts, SP complete all as specifed and as directed

S&F stepped type electronic fan regulator flush type, 120 watts single module, complete all as specifed and as directed.

M&L in replacement of submain wiring complete with 2 x 6.0Sqmm (nominal area) FRLS, PVC insulated, unsheathed and multistranded copper conductor cable ISI marked, and 1 x 6 Sqmm( same specification ) as earth wire in existing PVC conduit complete all as specified and as directed.

S&F LED energy efficient integrated battens fittings, PVC extruded heat sink with shatter proof opal shell of polycarbonate compound, not less than 18 Watt& THD < 10% & P.F> 0.9 & efficacy (Lm /w) > 120 & CCT - 3000 to 6500K, cool/warm white as per site requirement complete all as specified and as directed.

S&F LED energy efficient integrated battens fittings, PVC extruded heat sink with shatter proof opal shell of polycarbonate compound not less than 10 watt & THD < 10% & P.F> 0.9 & efficacy (Lm /w) > 120 & CCT - 3000 to 6500K, ripple < 5% cool/warm white as per site requirement complete all as specified and as directed.

S&F LED bulk head fitting not less than 6 Watt & THD < 10% & P.F> 0.9 & efficacy (Lm/w) > 120 & CCT - 3000 to 6500K, ripple < 5% complete all as specified and as directed.

S&F of energy efficient LED fittings 35W not less than 35 Watt & THD < 10% & P.F> 0.9 & efficacy (Lm /w) > 120 & CCT - 3000 to 6500K, ripple < 5% LED 6K suitable for building security light pressure die cast aluminium roadway luminaire with high power LEDs and HF electronic driver complete all as specified and as directed.

S&F of street light bracket incl clamp, nut and anchor bolt etc make to shape for street light fitting made out of GI pipe light grade 25 mm bore 1.0 mtr long on bend to shape the top of wall of existing building complete all as specified and directed.

Taking down of ceiling fan any type size complete with blades, fan clamp etc and depositing to MES store yard after dismantling blade complete all as specified and as directed.

Taking down of exhaust fan any type, size complete with blades, and depositing to MES store yard complete all as specified and as directed.

Refixing Ceiling fan any type size complete with blades and accessories and provision of flexible cable from connector to ceiling rose complete all as specified and as directed

S&F BLDC (Brushless Direct Current) Ceiling Fan, 1200 mm suitable for regulator, sevice value (cmm/w) > 6.85, not less than Air delivery 215 cum/minute, voltage 220V,having full copper motor winding & ribbed 3 Nos A/M blades. The fan shall have BEE 5 star rating and making necessary electric connection of suitable PVC copper wire from ceiling rose to ceiling fan complete all as specified and directed.

Refixing of exhaust fan any type size complete with blades, fastners including provision of flexible cable from connector to ceiling rose complete all as specified and as directed.

S&F of metal body exhaust fan with copper winding 225 mm sweep 230 volt AC with inbuilt grill , complete all as specified & directed.

M&L cutting/opening of hole through out the wall as suitable for exhaust fan of size 225 MM sweep and fixing of nut bolts with 4" anchor fastner of suitable size and making good the disturbed surface and all as per site requirement.

S&F of Ventilating fan 200 mm sweep plastic body type including self cousing louver and making all electric connections, complete all as specified and as directed.

S&F Geyser 25 litre capacity vertical type with steel body and glass inner lined and copper heating element upto 2KW capacity, BEE, 5 star rated complete with all accessories such as safety value thermostate, NRV etc including fastners for hanging thermostat control with NRV at inlet and CP and PVC connection for inlet and outlet upto stop cock, complete all as specifed and as directed.

M&L Rigid non-metallic PVC conduit of 20MM dia and inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc including all necessary connection complete all as specified and directed.

M&L Rigid non-metallic PVC conduit of 25MM dia and inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc including all necessary connection complete all as specified and directed.

S&F in replacement of MS box of size 100 x 100 mm x 40mm complete all as specified and as directed.

S&F in replacement of MS box of size 175 x 100 mm x 40mm complete all as specified and as directed.

S&F in replacement of MS box of size 250 x 200 mm x 40mm complete all as specified and as directed.

S&F in replacement of hylem sheet 3mm thick of size duly cut for any number of switches, sockets, regulator etc as per site requirement, acomplete all as specified and as directed.

Taking down old U/s cubical panel consisting of incoming MCCB, Bus Bar, outgoing MCB/Isolator, U/s energy meter and wiring complete Note: Energy meter retrieved from the cubical panel to be deposited to MES store yard

S&F metallic / polycarbonate for single phase prepaid meter with door glass incl.all type of fixing accessories etc complete all as specified & as directed.

S & F MCCB incommer Distribution Board ( Vertical Load line DB) double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, VTPN 04 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCCB as incommer and MCB as outgoing and making all necessary connection complete all as specified and as directed.

S&F MCCB, 415 volts, three pole of cap 125 Amp, 10 KA, ICS = 100% ICU, with Thermal - Magnetic Release, including necessary spreader / thimbles of suitable size and making connections complete all as specified and as directed.

S&F MCCB, 415 volts, three pole of cap 160 Amp, 10 KA, ICS = 100% ICU, with Thermal - Magnetic Release, including necessary spreader / thimbles of suitable size and making connections complete all as specified and as directed.

S & F in replacement of Distribution Board double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection surface mounting SPN 8 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc complete all as specified and directed.

S & F in replacement of of Distribution Board double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection surface mounting SPN 12 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc complete all as specified and directed.

S & F in replacement of MCB 'C' Curve type suitable for 240 volts AC supply, SP with over load and short circuit protection and rupturing capacity not less than 10 KA of capacity 6 to 32 amps complete all as specified and directed.

S & F in replacement of Isolator suitable for 240 volts AC supply, SPN of capacity 32/40 Amps complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel from earth plate to DB making necessary PCC 1:2:4 type B-1, Pit cover frame, GI pipe 15mm dia light grade for protection of earthwire, GI pipe medium grade 20 mm dia for watering with funnel, wiremesh, salt and charcoal dust in layeres all around the plate complete all as shown in electric plate No.3.complete all as specified or indicated including testing on completion.

S&F of single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB with 20 Amp.complete all as specified and as directed.

M&L XLPE insulated, amoured heavy duty electric cable insulated, PVC sheathed, galvanised steel strip amoured with aluminium conductor, 1100 volts grade, of size 35 Sqmm 3.5 core suitable for earth system fixed/under floor wall including all necessary connection complete all as specified and directed. Note: The cost aluminium thimble/lugs and cable gland etc is included in quoted rate.

S&F of Galvanised steel tubing light grade of size 40mm bore for passing cable complete all as specified and directed.

S&F non returm valve 15mm dia chromium plated including connection in GI pipe at mixture in washbasin complete all as specified and directed.

L G BUILDERS

VED PRAKASH ARORA

imran construction company

AMIT ASSOCIATES

Global Enterprises

ASSOCIATED CONSTRUCTION CO.

M/s. Kansal Construction Co.

JYOTI ENTERPRISES

V r traders

CHOPRA BUILDERS

Pooja Singla Builders And Engineers Pvt Ltd

M/s. Kansal Construction Co.

V r traders

M/S Chhavi Constructions Co

imran construction company

Global Enterprises

JYOTI ENTERPRISES

CHOPRA BUILDERS

VED PRAKASH ARORA

L G BUILDERS

AMIT ASSOCIATES

Pooja Singla Builders And Engineers Pvt Ltd