PROVN OF DUST PROOFING AND ALUMINIUM FRAMING WITH GLASS PANEL AT BLDG NO P 484 IN E ZONE AT RMS PROVN OF BOUNDARY WALL NEAR BLDG NO P 16 OT COMPLEX IN D ZONE AT RMS ADDN ALTN TO JCOs OR TOILET AT SD BR IN M ZONE AT RMS PROVN OF TEMP TOILET NEAR BLDG

Amount

Demolition of plain cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

Taking down chowkhat or frames not exc 1.5 Sqm each (without taking off shutter from the frame) complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed by Engineer-in-charge.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quions, arches, pillers etc complete all as specified and as directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings etc complete all as specified and directed.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in deep; for foundation etc or for shafts, wells, cesspits, manhole, pier holes, etc n.exc 10 Sqm on plan and n.exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and as directed

M&L for PCC (1:4:8) type D-2 (using 40mm graded crushed stone agg) as in foundation, filling and mass concrete complete all as specified and as directed

M&L for brick work with sub class `B' bricks (using old size burnt bricks) straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specified and as directed

M&L for brick work with sub class `B' bricks (using old size burnt bricks) straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and as directed

M&L 25 mm thick PCC (1:2:4) type B-0 (using 12.5 mm graded stone agg) as damp proof course to horizontal or vertical surfaces including necessary form works, applying evenly a coat of blown type bitumen at 1.50 kg per sqm and blinding with clean dry sand @ 0.05 cum per sqm including 150 micron thick polythene film laid on a coat of bitumen primer @ 0.30 to 0.50 kg per sqm complete all as specified and as directed.

M&L for RCC Nominal Mix Type A-1 (1:1.5:3) (using 20 mm graded stone aggregate) as in foundation, including rafts, footings, foundation beams; plinth beams; bases for columns, etc basement slabs under reamed piles and mass concrete complete all as specified and as directed.

M&L for RCC Nominal Mix Type A-1 (1:1.5:3) (using 20 mm graded stone aggregate) as in columns, pillars, piers, posts and struts complete all as specified and as directed.

M & L for RCC (1:1.5:3) type A-1, Nominal Mix (using 20 mm graded granite stone aggregate) as in beams, cantilivers bressumers, limited over 1.5 m spam etc complete all as specified and directed.

Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and as directed.

Use and waste of formwork to sides of pillars posts, struts, piers, columns and stanchions finished the suface rough complete all as specified and as directed.

Use and waste of formwork to sides and soffits of floors or roof beams, beams haunchings, girders,bressummers lintels, cantilevers, shelves including supports overhangs etc also splays between floors and beams etc.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and as directed.

S&F steel work in tubular trusses, post, purlins including special shaped washer etc. Complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade st-240 complete all as specified and directed by Engineer - in – Charge

M&L for mild steel works as in Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

S & F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe 410 -W (Gde- E- 250) quality- A complete all as specified and as directed.

M&L for mild steel TMT bars 10mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed

All same as per item No 22.00 (here-in-before) but 5mm dia and over and including 10mm dia in stirrups spacers and binders

Returning filling in trenches including spreading leveling watering and well ramming in layers not exceeding 25 cm thick all complete all as specified ans as directed.

Removing of excavated material not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point all complete all as specified ans as directed.

M & L for rendering 15mm thick on cement mortar (1:4) mixed with water proofing compound @ 3% of qty of cement finished of brick or concrete work finished the surface even and smooth without using extra cement complete all as specified and as directed. Note:WPC will be measured and paid separately.

M&L for Rendering 10 mm thick in CM (1:6) on other than fair face of brick-work or concrete surface to be finished even fair without using extra cement complete all as specified and as directed.

Supply only integral water proofing compound etc complete all as specified and directed.

M&L for Complete removal of existing treatment and applying two coats of oil bound distemper white or tinted on walls over a coat of primer complete all as specificed and directed.

M&L for preparation of new plastered surfaces and applying two coats of cement base paint over a coat of primer of approved shade on walls complete all as specified and as directed.

M&L of sand filling under floor well ramming including watering as required Spreading & leveling in layers n.exc. 25cm thick complete all as specified and directed.

M&L for hardcore of gauge n.exc 63mm, deposited, spread and levelled in layers n.exc 15cm thick, watered and rammmed to a true surface complete all as specified and directed.

M&L PCC (1:4:8) type D-2 75mm thick as in sub base of floor complete all as specified and directed.

M&L for Non Skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors laid over and including 15mm thick screed bed or bedding layer of cement mortar 1:6 for laying floor finishes, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and as directed.

M&L for Glazed ceramic coloured tiles in vertical surface 300 mm X 200 mm / 350 x 250x 7mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tile over and including baking coat of 10 mm thick in Cement Mortar (1:4), complete all as specified and as directed.

M & L for PCC (1:4:8) type D-2, 100 mm thick (using 40 mm graded stone aggregate) as in hardstanding complete all as specified and as directed.

M&L for 75 mm thick PCC (1:3:6) type C-2 , (using 40 mm graded stone aggregate) in plinth protection/aprons/path laid to slope of 1:12, finished fair and even without using extra cement with and including all necessary formwork to divide the area in panels, finishing exposed edges fair or rounding or chamfering where directed and providing 10 mm wide joints throughout thickness of plinth protection duly filled with mastic filling (one part of hot bitumen 85/25 and three part of fine sand by weight) complete all as specified and as directed.

M&L for chequered cement concrete tiles of size not less than 300x300x25mm thick laid over and including 15mm thick screed bed for laying floor finishes in cement mortar 1:6, etc, set, jointed and pointed in neat cement slurry with grey cement and pigments complete all as specified and as directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, as per specification complete all as specified and as directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined to-gether with solvent cement as per specification complete all as specified and as directed.

S&F butt hinges medium grade cold rolled mild steel and fixed size of hinges 100 mm long size complete all as specified and as directed.

S&F Aluminium anodised barrel tower bolt of extruded section and fixed 150 mm long complete all as specified and as directed.

S&F Aluminium handle cast type anodised 100 mm long complete all as specified and as directed.

S&F for steel ventilator with top hung shutter including hinges steel peg stay, complete all as specified and directed.

M&L for sheet glass, obscured or frosted 3mm thick and glazing with oil putty in squares. nexc 0.5 Sqm each complete all as specified and directed.

S&F 15mm dia unplasticised PVC pipes of pressure rating 10kgf/sqcm fixed complete to walls, ceilings or in floors etc complete all as specified and as directed.

S&F 20mm dia unplasticised PVC pipes of pressure rating 10kgf/sqcm fixed complete to walls, ceilings or in floors etc complete all as specified and as directed.

S&F in repair 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or fixed to floor complete all as specified and as directed.

S&F of 110mm dia PVC (SWR) bends complete all as specified and as directed.

S&F(SWR) 110mm bore pipe junction single (single T) equal and unequal with access door complete all as specified and as directed.

S&F in repair 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or fixed to floor complete all as specified and as directed.

S&F of 75mm dia PVC (SWR) Vent cowl complete all as specified and as directed.

S&F Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) and including EWC Seat cover complete all as specified and as directed.

S&F bib tap cast copper alloy, chromium plated with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule suitable for 15 mm dia bore pipe and fixed as approved by complete all as specified and as directed.

S&F 15mm bore angle stop cock , cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, screwed both ends for iron pipe complete all as specified and as directed.

S&F 15mm bore Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed.

M & L for RCC (1:1.5:3) type A-1, Nominal Mix (using 20 mm graded stone aggregate) as in slabs supported on walls, beams and columns in floor , roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L form work with fair finished to soffits of suspended slabs such as roof slabs, floor slabs, landing and similar work nexc 200mm thick (horizontal or sloping) complete all as specified and directed.

S&F PVC valveless, syphonic action type, 10 ltr flushing cistern, low level,white, with inlet, ball valve, float and handle including brackets complete all as specified and as directed.

S&F PVC connection 15mm dia and 45cm long with two Nos of brass checknuts and washerscomplete all as specified and as directed.

S&F vitreous china wash basin, size 550 x 400mm white including brackets, and waste coupling & pipe of 32mm dia, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other and fixed complete all as specified and as directed.

S&F soap dish, vitreous china white, aprox size 160 X 160 X 90 mm. fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F CP towel rail 600mm long with brackets, chromium plated 20mm dia in repair complete all as specified and directed.

S&F CP grating 100mm dia PTMT with waste hole complete all as specified and directed.

S&F CP Health Faucet with 1 mtr metalic Expandable tube & hook complete all as specified and directed.

S & F 110mm dia, PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed.

S&F brass chromium plated shower rose 125 mm in size with or without swivel joints any size incl fixing to steel pipe or union, complete all as spfd & directed

M&L for preparation of two coats of synthetic enamel paint over one coat of red oxide,zinc chrome primer on newly prepared steel surface of any description,over 10cm width or girth,not other wise described all as specified and directed by Engr-in-Charge.

S&F vitreous china half stall urinal white including flushing cistern , with grating and union for discharge pipe including waste pipe of polythelene of low or high density or PVC 32mm dia and including Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe(Minimum weight 60gms) & 32 mm waste coupling of PTMT (half or full threaded) complete all as specified and as directed.

S&F rotational moulded polyethylene 500 Ltrs Capacity water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position in SSR Part-I) with and including ball brass valve, with polythelene float and fly nut complete screwed down for iron pipe of 20 mm dia complete all as specified and as directed.

S&F for 20mm Gun mental, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

M & L for precast cement concrete (1:2:4) type B-1 using 20 mm stone aggregate as in manhole cover slabs round square or rectangular in shape and set in CM (1:4) complete all as specified and directed.

M&L for Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement including forms moulds complete all as specified and as directed.

Surface excavation n.exc 15cm deep and getting out in soft/ loose soil complete all as specified and as directed.

M&L for RCC Nominal Mix Type A-1 (1:1.5:3) (using 20 mm graded stone aggregate) as chajjas complete all as specified and as directed.

Use and waste for formwork to chullah hoods, cha jjas, troughs and similar items in cluding edge complete all as specified and directed.

S & F for 4 mm thick of size 600x600mm HSPC (high pressure Steam Cured) non asbestos fibre cement reinforced multipurpose board, pre-painted self embossed, textured designer board E-Board Classic fixed or laid/inserted to timber/ GI frame work with screws to be fixed in ceiling flat or sloping and Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre both ways, size of grid 605 x 605mm fixed with steel dash fasteners or from purlin from the roof with alignment clip including providing provisions for light fixtures of any size i complete all as specified and as directed.

M&L for applying two coats of oil bound distemper over a coat of primer on new plastered surfaces of walls including preparation of surface complete all as specified and directed.

S&F tubes medium grade, galvanised wih all fittings and fixed complete to walls and ceiling or laid on floors etc, 15 mm bore complete all as specified and as directed.

S&F tubes medium grade, galvanised wih all fittings and fixed complete to walls and ceiling or laid on floors etc, 20 mm bore complete all as specified and as directed.

S&F in repair 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall complete all as specified and as directed.

S&F 75mm PVC(SWR) bends any radius complete all as specified and as directed.

M&L for vitreous china squatting pan, Orissa, pattern size 580 x 440 mm white with integral foot rests(excluding flushing cistern and flush pipe)including connection to trap and to flushing pipe, anti-syphonage pipe etc complete including making good to floor complete all as specified and as directed.

S&F toilet paper holder, coloured vitreous china, box type fixed in wall complete all as specified and directed.

S&F Glass shelves, with 12mm thick desher glass incl CP brackets with brass nuts 300 mm long complete all as specified and directed.

M&L for PCC (1:3:6) type C-2 (40mm grade stone aggregate) as in bed to 110 mm dia SGSW /PVC pipes including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

S&F rotational moulded polyethylene 1000 Ltrs Capacity water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position in SSR Part-I including ball brass valve, with polythelene float and fly nut complete screwed down for iron pipe of 20 mm dia all as specified and directed. .

S&F for depth 0.70m – 1.65 m, DWCPE (SN8) 180 (OD)/163(ID) mm diameter Pipes laid on 150 mm thick PCC (1:3:6) type C-2 including packing under and haunching against the sides of pipes bed with excavation in any type of soil, including manholes/drop manhole of standard size made of Brick masonry/ RCC/Precast RCC with SFRC ventilating cover and frame, Includes all items and activities to execute and make sewer line functional complete all as specified and as directed.

M&L PCC (1:2:4), type (B-2), 50mm thick as in base course complete all as specified and as directed.

M&L for Coloured /light shade vitrified ceramic tiles 10mm thick (square/regtangular) polished , area of each tiles exc 0.18 Sqm but not exc 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & incl 15 mm thick screed bed or bedding layer in cement mortar (1:6) complete all as specified and directed.

M&L for Abrasion resistant self-levelling epoxy floor coating with solventless epoxy 3mm thick (2mm Screed and 1mm top coat) withstand attacks by oils lubricants, alkalis,acids,water, abrasion and impact like no other polymers with excelent bonding properties applied with following methods complete all as specified and as per manufactures instruction and as directed by Engineer in Charge. :- (i) Cleaning and Surface Preparation. (ii) Primer Coating (iii) Cracks and joint filling (iv) Epoxy finish coating

S&F aluminium anodised grill with mesh size 75 mm and aluminium bar 6 mm XPM type including all accessories such as channels for fixing grill screws etc, aluminium section 15 micron thick anodizing complete all as specified and directed.

M&L for fixing 4 mm thick anodised aluminium composite panel fixed in aluminium frame including necessary rubber beading, jointing cleats complete all necessary items to fix with frame and all as specified and directed by Engineer-in Charge.

S&F Sheet glass 4.8mm thick clear/sun shade colour glass, ordinary quality and glazing with oil putty in squares exceeding 0.5sqm in each pane complete all as specified and as directed.

S & F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F Aluminium alloy anodised sliding door bolt with hasp and staple (bolt type fixing clips of sheet cast or extruxded section(300 mm long) complete all as specified and as directed.

S&F floor door stopper overall length of cover plate 150mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and as directed.

S&F aluminium (extruded section) body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and as directed.

M & L for PCC 25 mm thick type B-0, (1:2:4) (using 12.5 mm graded stone aggregate) as in levelling course of floor complete all as specified and as directed.

M & L rendering 15mm thick in cement mortar (1:6) on fair faces of brick or concrete work even and smooth without using extra cement complete all as specified and directed.

S&F draperly rod /Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers complete all as specified and as directed.

M&L for Preparation of new ceiling surfaces and applying three coats of white wash complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of oil emulsion distemper over and including a coat of primer over wall care putty (2mm thick in two layers) on wall surfaces complete all as specified and as directed.

M&L for brick work with sub class B bricks(using old size burnt bricks) straight or curved on plan exceeding 6 m mean radius, built in Cement Mortar (1:4) complete all as specified and as directed.

S & F providing precast cement concrete louvres and jallies,type B-0, 1:2:4 (using 12.5 mm graded stone aggregate) 30mm thick (measured solid) and setting in mortar 1:4,including necessary form work and mould complete all as specified and as directed.

M&L for RCC (1:1.5:3) type B-1 (using 20mm graded crushed stone aggregate) as in cills, copings, benching on chajjas, roof kerbs, bed blocks and the like including weathering, slightly rounded or chamfered angles and throating as directed with and including necessary form work complete all as specified and as directed.

Material and labour for (concelaed Type) point wiring for One light point controlled by one, one way switch, including necessary chases cutting of wall for one light/fan/call bell point with 1.5 sqmm PVC insulated (FR-LSH) PVC sheathed multistranded copper conductor cable 1100 volts grade controlled by one way switch including 1.5 sqmm PVC (FR-LSH) insulated unsheathed copper cable multistrand conductor 1100 volts grade for continuity earth wire connected to common earth dolly drawn through and including PVC conduit with all accessories and sunk GI box for mounting of fittings like switch, socket and fan regulator etc and making good the distrubed surfaces as per the existing complete all as specified and as directed by the Engr-in-Charge

All as per item No. 109.00here-in-before but with 2.5 Sqmm for 3 pin 15 Amps switch socket point on independent board along with one run of 2.5 Sqmm copper conductor green in colour as earth continuity conductor connected to earth dolly complete all as specified and as directed.

M&L for Point wiring complete for One light/fan point controlled by one, one way switch with two runs of 1.5 sqmm single core PVC insulated FR-LSH cable 1100 volts grade with multi-stranded copper conductors, drawn through and including PVC double locked Casing & caping/PVC Conduit pipe including provision of 1.5 sqmm, FR-LSH, PVC insulated copper cable as earth continuity conductor connected to common earth dolly, including PVC rectagular box for mounting switches / sockets / regulators etc. with 3 mm thick plastic laminated sheet cover of suitable size as required at site complete all as specified and as directed.

S&F Switch piano flush type single pole, one way 5A complete all as specified and as directed.

S&F Switch socket combination 2 in 1, 5A/16A, 5 in 1 flush type complete all as specified and as directed.

S&F ceiling rose 3 terminal PVC/Polycarbonate isolated body with PVC round/squareblock complete all as specified and as directed.

S&F 20W LED, 4', Wall mounted LED batten, extruded aluminium heat sink provided for efficient heat dissipation & integrated electronic driver.etc with all accessories internally pre-wired and fixing the same and connecting up with flexible copper cable from ceiling rose to the light fitting complete all as specified and as directed.

S&F in repairs LED Light fitting 1 x 10 watt (2 Ft), Wall/ Surface mounted, intergrated type with all accessories internally prewired and incl connecting up with, including two Nos PVC blocks and connecting up with flexible copper cable of size 0.75 Sq mm 3 core and flexible pipe from ceiling rose to the light fitting complete all as specified and as directed.

Supply , fixing and testing in replacement of LED Bldg Security light fitting of capacity 25 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete including 1.2 mtr GI bracket of 25mm bore light grade bent to shape and fixed on wall with metal fastners 2 Nos 10mm dia incl drilling of holes as reqd and connecting up with flexible copper cable of size 0.75 sqmm 3 core from ceiling rose to the light fitting complete all as specified and directed by Engr-in-Charge

Supply, Fixing and testing of vertical type wall mounted storage water heater of Capacity 25 Ltrs BEE 5 Star rated or minimum Standing Loss of 0.511 kWh , 240V, 50Hz with Maximum power consumption of 2KW , dry powder fero glass line coating technology for inner tank with incoloy heating element with minimum 4 years warranty , ABS outer body , 2 units of PVC connection pipe with length of 450mm length for hot and cold water supply with complete Accessories complete all as specified and as directed.

M&L for sub main wiring with two runs of 4 Sq mm and one run of 4 Sq mm for earth wire with multi standard copper conductors, 1100 volts grade, drawn through and including PVC double locked Casing & caping including complete all as specified and as directed. NOTE:- two runs of 4 Sq mm + one run of 4sq mm and one run of PVC casing & capping and its accessories of suitable size shall be measured as one unit length

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm complete all as specified and directed.

Supply and laying tubes Medium grade galvanised GI tubing with all fittings, fixed complete to walls/poles/laid in floors/trenchs/road crossing of size 15 mm dia bore complete all as specified and as directed.

S&F Stop valves, cast copper alloy, fancy type, chromium plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed all as per specified and as directed. : Make : Jindal/Prakash surya/TATA

S&F 15mm bore Bib tap fancy type chromium plated with long shank complete all as specified and as directed Make: Jindal/Prakash surya/TATA

S&F MCB Distribution board double door type SPN 8 way, sheet steel, powder coated, with bus bar neutral link & earth bar etc. and fixing MCBs of various rating capacity complete all as specified and as directed.

S&F MCB Distribution board double door type SPN 4 way, sheet steel, powder coated, with bus bar neutral link & earth bar etc. and fixing MCBs of various rating capacity complete all as specified and as directed.

S&F MCB SPN 32 amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and as directed.

S&F MCB SP 5-32 amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with onnection testing and commissioning complete all as specified and as directed.

M&L for laying of LT UG cable, XLPE insulated, galvanised steel strip or wire armoured, heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area of 16sq mm, 2 core complete all as specified and as directed. NOTE :- (i) Excavation and earth work, sand cushioning, cable protection cover, pipe etc. shall be measured and paid seperately under relevant items.

M&L for spread fine river sand in trenches complete all as specified ans as directed. NOTE: Punned down thickness shall only be measured and paid.

M&L for laying brick sub class 'B' old size burnt bricks for cable protection of size 230mmx115mmx75mm complete all as specified and as directed

Supply & laying tubes ' light grade' galvanised, with all fittings, fixed complete to walls, poles, ceilings or laid in floors/ trenches/ road crossing for protection of cables of size 40 mm dia bore complete all as specified and as directed.

M&L for earthing complete with galvanized steel earth plate electrode of size 600x600x6mm thick buried directly in ground (earth pit not less than 2.25m deep below the normal ground level) with top edge of the earth plate not less than 1.5 mtr below normal ground level connected to galvanised earth lead wire 4 mm dia as earth lead connectd by means of bolts, nuts, washers and check nuts all as shown in electrical plate No 3 of MES SSR Part-I, including testing on completion complete all as specified and as directed. NOTE:- (i) The unit rate shall also included for earth work in hard/ dense soil, PCC (1:3:6) type C1 chamber, CI frame with CI cover funnel with GI watering pipe 20mm dia Medium grade, GI protection pipe light grade 15mm dia and wire mesh complete in addition to item No 1 (a) to (e) of preamble (notes) under sub heading earthing, specified on Sl Page No 441 of MES SSR Part-II. (ii) Earthing lead and GI protection pipe beyond 7.5m will be measured and paid separately.

PERFECT BUILDERS AND SUPPLIERS (BID ID -3512424)

SHRI MADAN SINGH (BID ID -3512771)

M/S Lucky Builders (BID ID -3514665)

SHRI HRIDAY NARAIN GIRI (BID ID -3513111)

KAILASH KUMAR LADHA (BID ID -3513142)

Shri B K Ukil (BID ID -3514064)

M/S CELL HEART (BID ID -3514677)