163/EDC(H)/2023-24

Amount

Safe carriage, loading-unloading with proper stacking of following material from store centre to pit site/JE dump store.

P.C.C. /ST Pole 8.5/11 mtr long

11 KV Pin Insulator with Pin

11 KV Disc Insulator with fitting

ACSR Weasel Conductor

Earthing Rod

Stay Set

G.I. Wire 6/8/10 SWG

ABC Cable (3×50/3x95/3x120) mm2

LT XLPE Cable Aluminum 3.5×400mm2

LT XLPE Cable Aluminum 1×240mm2

100 KVA T/F

250 KVA T/F

Line Meterial

Distribution Box 3-phase

Erection of PCC/ STP 8.5/11 mtr long single pole with Grouting & with all accessories for LT line or 11 Kv line (Only Pole and Insulator Supplied by department)

Erection of PCC/ STP 8.5/11 mtr long double pole with Grouting & with all accessories (Only Pole and Insulator Supplied by department)

Grouting and Nozzling of 11 KV stay set complete including fixing of necessary clamps. Accessories required including its grouting by civil material (sand, brick blast & cement). All material except stay wire shall be supplied by the contractor.

Ordinary earthing by 11 KV MS earth Rod 2500 mm long as per RESPO schedule. All material except earthing rod shall be supplied by the contractor.

Laying of LT XLPE Cable of different size

Earthling by way of Boring and lowering the "B" class GI pipe (Gindal ) of 50mm dia from ground upto water level not less than 20mtr as per standard practice

Placement of 11/0.4 KV T/Fs from dump place to newly constructed T/Fs plinth & installation, commissioning of 100/250/400/630 KVA T/Fs of T/F Plinth and including jumpering with the system ( All the required martial for above job shall be provided by contractor except T/Fs)

Stringing & Sagging of three phase 11 kv line

Stringing & Sagging ABC

Installation & commissioning of Distribution Box for ABC Bunch Conductor

Looping & chopping of tree branches for clearance of HT/LT line after clearance of line throughout pieces of tree branches of site

Supply & Fixing of LT Fuse unit for 250 & 400 With Grout (All Material Arrange by Contractor at his own cost)

Supply and Fixing of HT Fuse Set

Concreating of Pole

Construction of toe wall around the 11/0.4 kv S/S, fuse unit size 0.75 Mt. At Base and 0.23 Mt. At top as per RESSPO Norms by lst class bricks in the ratio 1:6, Base concreting of the wall to be done in ratio 1:6:12 and plaster 12 mm thick in ratio 1:4.& fabrication of fencing with wire mesh 10SWG(37mmx50mm)(all material to be arranged by contractor).

Construction of T/F plinth of size 2x2x1.5 m on a padding 0.25M deep in ground 1:5:10 cement sand and brick ballast on the top of padding brick work Ist class brick of 0.95 mtr height & 0.35 mtr wall will be constructed. Rest wall should be 0.23 mtr thick. Brick work in ratio 1:4 cement & cores Sand in the hollow portion the sand should be filled from the ground level up to 15 centimetres below from the top of wall, Cement, sand & brick Ballasts should be filled up to 15 centimetre. Two no. of channel 100x50 in length 1500mm will be grouded.0.35 CM.RCC will be done with cores sand, cement and stone ballast in the ratio of 1:2:4.The T/Fs plinth should be plastered on all sides 12mm thick in ratio 1:6 by cement and cores sand.(All the material to be arranged by the contractor).

M/S RUDRA CONTRACTOR AND SUPPLIER BAREPUR ANDHARRA HARDOI

M/S S.K. CONTRACTOR AND SUPPLIER