SPECIAL REPAIR ALTERATION TO BLDG NO P-9 and P-10 ( GUARD ROOM and SERVANT QTRS) (JOB NO 41SA/SR BLDG/14/2023-24) andADDN/ ALT TO BLDG NO P-229 (SARVA DHARM STHAL) (JOB NO 41SA/MINOR/01/2024-25) AT LICHUBARI IN JORHAT MIL STN UNDER GE JORHAT

Amount

NOTES :The bidders/contractors are advised to read tender document & all corrigendum/ amendments and General conditions of contracts before entry/quoting the rates.

Demolition of cement concrete ( un-reinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) and removing debris to a distance n.exc. 50 m etc complete all as specified and as directed.

Material and labour for 75 mm thick plain cement concrete M-10(Nominal Mix) using 20 mm graded stone aggregate as in plinth protection, finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for 100 mm thick plain cement concrete M-7.5(Nominal Mix) using 40 mm graded stone aggregate , finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for pre-polished chequered Cement Concrete tiles of 25 mm minimum thick, size of (square/ rectangular) area of each tile exceeding 0.09 Sqm but not exceeding 0.16 Sqm double layer machine pressed set ( as per IS 1237-2012), jointed and pointed in neat cement slurry in floors and cut & polished in white or coloured cement to match over and including 15mm thick screed bed in CM (1:4) complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to stores and rubbish off the MOD premises complete all as specified and as directed.

Material and labour for virified Ceramic dark shade tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM (1:6) complete all as specified and as directed.

Material and labour for virified Ceramic dark shade tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick screed bed in CM (1:4) complete all as specified and as directed.

Material & Labour Glazed ceramic tiles 450x350/ 350x250 x7 mm(Coloured) on vertical surfaces such as skirting, dados and riser to steps etc. set and jointed in neat cement slurry and pointed in coloured cement to match complete over 10mm thick screed bed vertical layer in CM (1:4)all as specified and as directed.

Material & Labour Non skid ceramic tiles, coloured, 7 to 8 mm thick (square/rectangular area of each tile exceeding 0.11 Sqm and not exceeding 0.18 Sqm , in floors etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed layer in CM (1:6) including roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc and brushign neat cement slurry with 3.0 kg of cement per Sqm complete all as specified and as directed.

Material & Labour 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.®over 15mm thick screed bed layer in CM (1:6) complete all as specified and as directed.

Demolition of brickwork any description and in any position , built in cement sand mortar etc complete all as specified and as directed.

Material and labour for Brick work with bricks class designation 75, old size, straight or curved on plan exceeding 6 m mean radius built in Cement Mortar 1:6 complete all as specified and as directed.

Taking down cement plaster from brick or concrete surfaces of any description including racking out joints, hacking for key, scrubbing down with water etc complete all as directed.

M&L for Rendering 15 mm in Cement Mortar 1:6 on fair faces of brick work or concrete surfaces finished even smooth without using extra cement to the plastered surface complete all as specified and as directed.

Material and labour for Rendering 15mm thick plaster in Cement Mortar (1:4) on fair faces of brick or concrete surface of wall and finished even and smooth without using extra cement, with water proofing treatment. Note:- Water proofing compound shall be measure and paid separately

Supply only l liquid water proofing compound ISI marked complete all as specified and directed.

Material and labour for Preparation of new plastered wall surface and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

Material and labour for Preparation of new plastered wall surface and applying two coats of oil bound distemper over a coat of primer chalk whitening etc complete all as specified and directed.

Material and labour for Preparation of old or previously untreated wall surface by washing with water , rubbing down and stopping of distempered and applying a coat of oil bound distemper etc complete all as specified and directed.

Material and labour for complete removal of old or previously untreated wall surface by washing with water , rubbing down and stopping of distempered and applying two coats of oil bound distemper over a coat of primer etc complete all as specified and directed.

Taking up or down 15mm bore galvanised steel tubes, medium grade with all fitting and fixed to walls, ceiling, floors and segregated and stacked etc complete all as specified and as directed.

Taking up or down 20mm bore galvanised steel tubes, medium grade with all fitting and fixed to walls, ceiling, floors and segregated and stacked etc complete all as specified and as directed.

Supply and fixing of 15mm bore galvanised steel tubes, medium grade with all fitting and fixed to walls, ceiling, floors complete all as specified and as directed.

Supply and fixing of 20mm bore galvanised steel tubes, medium grade with all fitting and fixed to walls, ceiling, floors complete all as specified and as directed.

Taking down Chowkhats or frames with shutters (without taking off shutters from the frame)exc 1.5 sq. m but n exc 4 sq. m each complete all as specified and as directed.

Cutting holes exc half but nexc. one brick in brick walls in cement sand mortar depth of embedded portion of holdfasts or lugs measured from the face of the jamb into the wall for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and as directed.

S&F Iind class hardwood Small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary' labours; articles n exc 200 cu. cm each complete all as specified and as directed.

Supply and fixing Factory made PVC door frame of size 125mm x 50 mm double rebate with a wall thickness of 5mm PVC sheet made by joining 3 Nos heat bent PVC sheet 'C' channel of 5mm PVC foam sheet of sizes 35mm x 35mm x 25mm & 40mm x 55mm & 40mm x 25mm x 35mm using solvent cement . The two sides 'C' channel shall be reinforced with 19mm x 19mm MS square tube of 19 gauge. All the three 'C' channel shall be fixed to flat base of 5mm PVC sheet with solvent cement. The profile shall be mitre cut at two corners and joined by inserting 4 nos 150 mm long brackets of 15mm x 15mm MS square tube inside the 19 mm square tubes. The two vertical door frames are to be reinforced with 40 x 20mm MS tubes of 19 tubes duly filled with 18mm thick PVC through out the frame. The door frame shall be fixed to the wall usingf 100 mm long nickel coated dry wheel screws through the frame by using PVC fasteners. A min of 08 Nos of screws to be provided for each vertical member and minimum 4 Nos for horizontal members etc complete all as specified and as directed.

Supply and fixing Factory made Solid PVC Moulded Door Shutter, 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face &2mm prelam PVC Sheet on back face PVC sheet on back face, etc complete all as specified and as directed.

Supply and fixing Factory made solid panel wire gauzed PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded wire gauzed i.e. panel will be of wire gauze in lieu of PVC sheet panel. The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firmly; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at siteetc complete all as specified and as directed.

Taking down Chowkhats or frames with shutters (without taking off shutters from the frame) n.exc 1.5 sq. m each complete all as specified and as directed.

S&F Solid PVC door frame of size 50mm x 47 mm made out of 5 mm wood grain printed PVC sheet reinforced with Mild Steel square tube, suppling & fixing in opening as per drawing complete all as specified and directed.

Material and labour for Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawingcomplete all as specified and directed.

Supply and fixing of Butt hinges Stainless steel 100 mm size complete all as specified and directed.

Supply and fixing of Aluminium anodised barrel tower bolts of extruded section size 200 mm complete all as specified and directed.

Supply and fixing of Aluminium anodised barrel tower bolts of extruded section size 100 mm complete all as specified and directed.

Material and labour for extruded Aluminium alloy handles fabricated type anodised 150 mm size complete all as specified and directed.

Material and labour for extruded Aluminium alloy handles fabricated type anodised 125 mm size complete all as specified and directed.

Material and labour for 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

Material and labour for MS 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete complete all as specified and directed.

Supply and fixing of aluminium sliding window with powder coating (minimum thickness of powder coating 50 micron) including following components / specifications complete all as specified and as directed. (i) Two leaf glazed sliding shutter and one leaf gauged (fly proofing) sliding shutter. (ii) Opening of windows exceeding 1.50 Sqm but not exceeding 2.40 Sqm (iii) Thickness and weight per metre length of aluminium frame and section of shutter all as shown on drawing. (iv) All vertical/ horizontal joints shall be of extruded aluminium section so as to avoid any play between jointed members. (v) All other accessories such as jointing cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws, etc. (vi) Rest all as specified in drawing no CESZ/2015/TD/007 Sheet no 1R/5, 2R/5, 3R/5, 4R/5 & 5R/5.

S&F Anodised aluminium ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) etc complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for etc complete all as specified & as directed.

Materials and labour for Mild Steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290(Gde E-165) complete all as specified and as directedincluding taking dwon old one complete all as specified and as directed.

S&F Stainless steel wire cloth, 0.36 mm nominal dia of wire and avergae width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

Materials and labour for mild steel of grade• Fe-290 Gde-E-165 as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles complete all as specified and as directed.

Supply and fixing of sheet glass 4 mm thick ordinary quality fixed to aluminum door & window in squares in each pane of required size complete all as specified and as directed.

Supply and fixing Harrison rails, mild steel, chromium plated with fixing brackets,stops, rollers etc.complete all as specified and as directed.

Dismantling AC sheeting, plain or corrugated any thickness including eves gutter / rain water pipe complete & removal all as specified

Supply and fixing of pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick and an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Supply and fixing of pre-painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in ridges, tips, valley, gutters, length & girth as fixed with nail or screws complete all as specified and as directed.

Material and labour for Rolled mild steel in roof truss (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including cleats Fe-410 W (Gde E-250) Quality-B including one shop coat of zinc chromate primer after preparation of surface complete all as specified and as directed.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and as directed.

S&F LUXALON @ 84C linear false ceiling of Aluminium box shaped , 84mm wide and 12.5mm, plain bridge or hole with perforated panels clipped onto the Luxalon carrier etc complete all as specified and as directed.

Material and labour for preparation of new steel surface and applying two coats of synthetic enamel paint over a coat of red oxide primer on new steel and iron surfaces of any description over exceeding 10 cm in width or girth complete all as specified and as directed..

Supply and fixing in repair stop valve, cast copper alloy high pressure with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed , 15 mm bore complete all as specified and as directed. complete all as specified.

Supply and fixing in repair bib tap , cast copper alloy high pressure with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed , 15 mm bore complete all as specified and as directed. complete all as specified.

Supply and fixing in repair Brass chromium plated shower rose 125mm size with arm and wall flange etc complete all as specified and as directed. complete all as specified.

Supply and fixing in repair PVC grating 140 mm PTMT ( minimum weight 50 gms) etc complete all as specified and as directed. complete all as specified.

Supply and fixing PVC (SWR) floor trap 75 mm, plain with CP grating including joining and solvent cement complete all as specified and directed.

Supply and fixing Water closet (Squatt pattern) vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white with including CI ‘P’ or ‘S’ trap , integral foot rests (excluding flushing cistern and flush pipe) complete including provision of Plain cement concrete bedding (1:2:4) using 20 mm graded stone aggregate including taking down old unserviceable one and removing from site etc complete all as specified and directed.

Supply and fixing 15 mm dia 450 mm long PVC connection pipe with 02 nos PTMT nut at each ends with rubber washer etc complete all as specified and directed.

Supply and fixing as in repair of PVC low level flusing cistern 10 litres capacity white with ball valve & brackets with flush pipe , symphonic action type , dual flush type , etc complete all as specified and as directed.

Supply and fixing in repair Wash basins size 550 x 400 mm ,white Vitreous China (flat ball type ) , including cutting for and pinning in ends of brackets or erecting stand and making good wall surface complete all as specified and as directed.

Supply and fixing in repair of chromium plated pillar cock cast copper alloy screwed down with long body with wall flange, and fixed for 15 mm bore GI tube pipe and all accessories complete all as specified and as directed. complete all as specified.

Supply and fixing in repair Towel Rail 600 mm long of chromium plated fixed with and including chromium plated brass screws and wooden/plastic cleats complete all as specified and as directed.

Supplying, hoisted and fixed in position of rotational moulded polyethylene water storage tanks in double layers and cylindrical vertical type with manhole lids(closed top) of 500 litres capacity with ISI marked and all as specified in IS 12701 complete all as specified and directed .

Supply and fixing in repair Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 2 0 m m - 2 1 0 g m s) complete all as specified and as directed. complete all as specified.

Supply and fixing PVC (SWR) pipes 100 mm dia single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

Supply and fixing PVC (SWR) pipes 75 mm dia single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

Supply and fixing of PVC ( SWR) bend for 110 mm bore uPVC pipe complete all as specified and directed.

Supply and fixing of PVC ( SWR) bend for 75 mm bore uPVC pipe complete all as specified and directed.

Supply and fixing of PVC ( SWR) branch piece 110 mm bore single Y , equal or unequal etc complete all as specified and directed.

S&F Solid PVC door frame of size 50mm x 47 mm made out of 5 mm prelam PVC sheet reinforced with Mild Steel square tube, suppling & fixing in opening as per drawing complete all as specified and directed.

Supply and fixing 50 mm bore Low density polyethylene (LDPE) pipes of pressure rating 6 kgf/sq. cm fixed to wall , ceiling, pr in floor etc including cutting, chasing pinning and making good to disturbed surfaces as per existing etc complete all as specified and directed.

Demolition of cement concrete (Reinforced) of any description in any position not otherwise specifically provided for and removing debris to a distance n.exc. 50 m etc complete all as specified and as directed.

Material and labour for Reinforced Cement Concrete M-20 (Nominal mix) using 20 mm graded stone aggregate as in slab supported on wall ,roofs, landings, balconies, canopies, deck slabs and in shelves and the like including necessary formwork etc complete all as specified and directed.

Material and labour for Precast Reinforced Cement Concete cover slab type M-20 (Nominal mix) using 20 mm graded stone aggregate, set in Cement Mortar (1:4) including necessary formwork complete all as specified and directed.

Material and labour for TMT Bars Fe 500D 10mm dia & over cut to length bent to shape required inculding cranking bending spirally hooping for columns etc and binding with MS wire ennealed less than 0.9mm dia or securing with clip complete all as specified and directed.

S&F Sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F in repair 100 mm long aluminium anodised hasp and staple with ms hinges pin including bolts to hinge plate and fixed with stainless steel screws etc complete all as specified and directed.

S&F in repair MS CP peg set of 06 of standard quality fixed with stainless steel screws etc complete all as specified and directed.

S&F in repair continous piano hinges mild steel bright finish , width of flap 30 mm when opened , fixed with stainless steel screws etc complete all as specified and directed.

S&F in repair 18/19 mm thick PVC board one side laminated , cut to size as required and fixed in position for cabinets etc complete all as specified and directed.

Excavating in post holes (or similar holes) in soft / loose soil ,each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, etc complete all as specified and directed.

Material and labour for Hard core of gauge not exceeding 63 mm of broken stone or boulders , spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface

Material and labour for plain cement concrete M-10 (Nominal Mix) using 20 mm graded stone aggregate complete all as specified and as directed.

Material and labour for Mild Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 including one shop coat of zinc chromate primer after preparation of surface complete all as specified and as directed.

Material and labour for plain cement concrete M-10 (Nominal Mix) using 40 mm graded stone aggregate as in foundation, filling and mass concrete etc complete all as specified and as directed.

Material & Labour Non skid ceramic tiles, coloured, 7 to 8 mm thick (square/rectangular area of each tile exceeding 0.06 Sqm and not exceeding 0.11 Sqm , in floors etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed layer in CM (1:6) including roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc and brushign neat cement slurry with 3.0 kg of cement per Sqm complete all as specified and as directed.

Subtotal of Sch A part-I

SCHEDULE 'A' PART - II FOR B/R PORTION (Sl No __ to ____)

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and as directed.

Material and labour for point wiring with 1.5 Sq. mm (nominal area) PVC insulated and sheathed single core FRLSHcopper cable 1100 volts grade with stranded copper conductor in and including PVC rigid concealed conduit (heavy grade) and conduit accessories alongwith continuous earth wire 1.5 Sq mm PVC insulated and sheathed single core FRLSH cable 1100 volts grade with stranded copper conductor and connected to common earth dolly complete for one light/fan point controlled by one modular switch complete all as specified and as directed.

Material and labour for Point wiring with 1.5 Sq. mm (nominal area) PVC insulated and sheathed single core FRLSHcopper cable 1100 volts grade with stranded copper conductor in and including PVC rigid concealed conduit (heavy grade) and conduit accessories alongwith continuous earth wire 1.5 Sq mm PVC insulated and sheathed single core FRLSH cable 1100 volts grade with stranded copper conductor and connected to common earth dolly complete for modular one socket outlet 5 pin 6 amps on independent board complete all as specified and as directed. NOTES :-Flush steel terminal box, inner plate and front plates shall be measured and paid seperately. Cutting chases and making good in walls shall be deemed to be included in the unit rate.

Material and labour for Point wiring with 1.5 Sq. mm (nominal area) PVC insulated and sheathed single core FRLSHcopper cable 1100 volts grade with stranded copper conductor in and including PVC rigid concealed conduit (heavy grade) and conduit accessories alongwith continuous earth wire 1.5 Sq mm PVC insulated and sheathed single core FRLSH cable 1100 volts grade with stranded copper conductor and connected to common earth dolly complete for modular one socket outlet 5 pin 6 amps on same board complete all as specified and as directed. NOTES :-Flush steel terminal box, inner plate and front plates shall be measured and paid seperately. Cutting chases and making good in walls shall be deemed to be included in the unit rate.

Material and labour for Point wiring with 4.0 Sq. mm (nominal area) PVC insulated and sheathed single core FRLSHcopper cable 1100 volts grade with stranded copper conductor in and including PVC rigid concealed conduit (heavy grade) and conduit accessories alongwith continuous earth wire 4.0 Sq mm PVC insulated and sheathed single core FRLSH cable 1100 volts grade with stranded copper conductor and connected to common earth dolly complete for modular one socket outlet 5 pin 15/16 amps on independant board complete all as specified and as directed. NOTES :-Flush steel terminal box, inner plate and front plates shall be measured and paid seperately. Cutting chases and making good in walls shall be deemed to be included in the unit rate.

S&F Metal flush box 2 modular complete all as specified and as directed.

S&F Metal flush box 3 modular complete all as specified and as directed.

S&F Metal flush box 6 modular complete all as specified and as directed.

S&F Metal flush box 8 modular complete all as specified and as directed.

S&F White cover plate with frame (both ineer plate & outer plate cover) ,2 modular complete all as specified and as directed.

S&F White cover plate with frame (both ineer plate & outer plate cover) ,3 modular complete all as specified and as directed.

S&F White cover plate with frame (both ineer plate & outer plate cover) , 6 modular complete all as specified and as directed.

S&F White cover plate with frame (both ineer plate & outer plate cover) , 8modular complete all as specified and as directed.

S&F Modular socket 6 Amp 2/3 pin combined shattered 2 module ISI marked etc complete all as specified and as directed.

S&F Modular socket 16 Amp 2/3 pin combined shattered 2 module ISI marked etc complete all as specified and as directed.

Material and labour for Modular switch 16 Amp single pole one way ISI marked complete all as specified and as directed.

Material and labour for Modular switch 6 Amp single pole one way ISI marked complete all as specified and as directed.

Supply and fixing modular Fan step regulator, 120W - 2 module ISI marked complete all as specified and as directed.

Supply and fixing of sheet metal enclosure for MCBs to be used singal pole & nutral double door 8 Way 200 Amps rated busbar and including fixed with 25mm x 6 mm mild steel clamp of suitable length complete all as specified and as directed.

Supply and fixing ceiling rose surface bakelite 65x50mm three terminals complete all as specified and as directed.

Supply and fixing amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) 5 to 32 Amps , single pole and current carrying capacity in the MCB DB complete with connection testing and commissioning etc complete all as specified and as directed.

Supply & Fixing of LED street light fitting ( Building Security light) of 35Watt with LED lamp’s & driver and made of pressure die-cast aluminum housing, IP 65/IP 66 road way luminaries with UV stabilized polycarbonate cover or toughen glass cover & high power LED’s as light source with 110 Lumen per watt and electronic driver with efficiency > 85% . The light fitting shall be fixed on wall/pole with and including 25 mm dia( or higher size as per manufacturers recommendation) light grade GI pipe (bend to shape or as per manufacturers recommendation ) bracket 1.5 mtr long complete with MS flat iron clamp (clamps shall be 40 x 5 mm MS flat) nuts, bolts & washers including painting the clamps with two coat of aluminium paint over a coat of red oxide primer and including taking up old light fitting complete all as specified and as directed Make:- Model No- TRP-400-35-57-SL-LM-NSR of Crompton Greave/ NXT P 36L WH CR PC SD of Bajaj or equivalent model of make list as given in PS. Notes : GI pipe bracket and clamps shall be deem to be included above quoted rate..

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable three core1.00sq. Mm copper conductor flexible from ceiling rose complete., drive and made of epoxy powder coated extruded aluminium channel housing with high quality polycarbonate opal diffuser cover & high power LED’s as light source with 110 Lumen per watt (Minimum) and including all other standard accessories as per manufacture instructions ,internally pre-wired including connecting up etc complete all as specified.

Supply and fix exhaust fan made of sturdy Engineering plastic omplete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250 mm fixed to wall , writing the MES fan numbers with paint and 0.75 Sqmm , 3 core PVC insulated Flexible copper cable for connection from ceiling rose to fan complete all as specified and as directed.

Material & Labour for earthing with galvanised steel earth plate electrode of size 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25m deep below the ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to the galvanised earth lead by means of bolts, nuts check nuts and washers of galvanised iron using GI 4 mm dia wire as earthing lead as shown in electrical plate No. 3 of SSR Part-I connected to earthing test point all as specified or indicated including testing on completion including necessary excavation and earth work in soft/loose soil, returning filling, disposal of surplus soil, earth pit in PCC 1:3:6 type C-1 using 20mm graded stone aggregate pit, funnel, 20mm dia GI medium grade watering pipe, 40mm dia GI medium grade earth lead protection pipe, CI frame and cover, wire, copper lugs etc mesh, chorcoal and common salt in alternatee layer complete all as specified and directed .

Note: Schedule of credit (SCHEDULE OF CREDIT) amount of Rs ₹ ___________ mentioned on Page No ____ shall be deducted from the total quoted amount of BOQ.

A K DUTTA CHOWDHURY AND CO

PEE BEE INDIA

A M CHOUDHURY AND CO