SPECIAL REPAIR TO SINGLE OFFRS ACCN (BLDG NO P-39) AT AMAR SINGH CAMP OF 06 PARA (SF) UNDER GE (EAST) AGRA

Taking down of old roof treatment of any description including mud phushka, concrete padding,tiles,cement plaster from roof surfaces etc including cleaning ,brushing and watering to joints and grooves and throwing the same to a distance exc. 250 mtr and not exc 500 mtr from the roof of height 3 to 9 mtr etc complete all as specified and directed.

Material and labour for 25 mm thick PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in roof kerbs, paddings, mud stops slightly chamfered or rounded in edges including required grove cutting complete all as specified and directed.

Material & labour for cleaning the surface of the stone/concrete roof and slab with mechanical grinder and specialized water misting techniques applying water jet using a fine nozzle sprinkling system calibrated to spray a fine mist along the stone/concrete surface and removing complete all as specified and directed by Engineer in charge and applying one coat of sealer @ 0.2 kg/sqm with capacity of Drastic reduction in water absorption - ASTM C642-97 with Improved resistance to chloride penetration in concrete surface (RCPT) as per ASTM C1202 and Improved abrasion resistance of surface when tested as per ASTM C779 and low alkaline silicate based, first reacting with other free oxides and hydroxides like calcium hydroxide (free lime) inside the concrete to form corresponding silicates, which are stronger molecules. Total Solids Content 29-30% approx. Specific Gravity at 25°C 1.25 +/- 0.02 Ph Alkaline VOC Content Nil This sealer gels in the empty pores which is insoluble silica deposits. Finally forms a microscopic siliceous layers on the surface which results in strong ceramic coating, firmly bonded to the surface by strong silanol bonds. This is stable against UV and high temperature. Note:- (i) This item has to be applied on mother slab before laying any screed bed or PCC as a waterproofing process. (ii) This item shall be carried by authorised company by manufacturer.

M & L applying two coats of resin sealer @ 0.2 lit/sqm for each layerwith reinforced nanometer sized particles preventing “peeling off” effect from floor/bottom. It is advised to apply in following steps : first coat to be done on cleaned surface mixing with diluent as per manufacturer’s manual and after drying surface immediately final coat has to be applied on primed surface buffing can be further done for glossy surface complete all as specified and directed. Note :This item has to be applied on PCC or 10 mm thick plastered surface as a waterproofing process.This item shall be carried by authorised company by manufacturer.

M & L one coat of primer on well prepared surface as roof and parapet walls @ 0.2 lit/sqm (thickness = 0.85 mm )which is the combination of base and hardener water based epoxy system. It provides high hardness and abrasion resistance. It can be applied on dry or slightly damp substrates, without standing water. . After 24 hours of application of primer, and cleaning the surface with air blower, first coat of elastomeric pre-polymer hybrid chemistry based two component waterproofing membrane will be applied @ 0.2 lit /sqm for each layer (thickness = 0.85 mm) on roof and parapet walls. And second coat will be applied after 24 hours of first coat application etc complete all as specified & directed. Note-: this item shall be carried by authorised company by manufacturer as approved by GE.

Applying the non shrink high mechanical strength properties epoxy based mortar @ 5kg / RM on all corner joints of wall to prevent the capillary formation from wall to roof area; by three component system comprising of base, hardener and quartz filler having ER Base and Hardener with Quartz filler etc complete all as specified & directed. Note-: This item shall be carried by authorised company by manufacturer as approved by GE.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar ficings, dressed stone work and pre-cast concrete articles complete all as specified and directed.

M&L for brick work with sub class ‘B’ bricks old size, straight or curved on plan exc 6 M mean radius, built in CM 1:6 complete all as specified & directed.

Taking down cement or cement lime plaster of any discription on brick or stone walls/ ceilings etc, including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for 15mm thick SmartCare ready mix plaster for External surface is a specially designed ready to use cement based plaster with high quality polymer additives and well graded sand and fillers which can be used for plastering on bricks, block, stone walls over a coat of acrylic polymer as well as concrete surfaces. complete all as specified and directed.

M&L for 10mm thick SmartCare ready mix plasterfor Internal surface is a specially designed ready to use cement based plaster with high quality polymer additives and well graded sand and fillers which can be used for plastering on bricks, block, stone walls over a coat of acrylic polymer as well as concrete surfaces. complete all as specified and directed.

Material and labour for Rendering 10 mm thick plastering in CM 1:3 on ceiling surface finished even and smooth without using extra cement complete all as specified and directed.

Material and Labour for preparation of newly plastered ceiling surface and applying three coats of white wash, complete all as specified and directed.

M&L Preparing newly plastered or un plastered surfaces of wall and applying two coats of oil bound distemper with roller application over a coat of primer over a coat of average 3mm thick wall care putty on new plastered surfaces complete all as specified and directed.

M&L for complete removal of existing treatment of old plastered surfaces of wall and applying two coat of oil bound distemper with roller on old decorated wall surfaces over 3 mm thick white putty complete all as specified and directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new wall surface complete all as specified and directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm including complete removal of existin treatment old wall surface complete all as specified and directed.

M & L for Preparing old plastered surface and applying two coat of white wash on ceiling complete all as specified and directed.

Dismantling stone slabs and tiles of any description or thickness in floors / dados, etc laid bedded and pointed in any mortar complete all as specified and directed.

M&L for coloured glazed ceramic tiles in vertical surface 600 x 1200x 10mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match tiles including 10mm thick rendering in CM 1:4 on brick wall complete all as specified and as directed .

M & L for Vitrified tiles 10mm thick (square/rectangular) area of each tile not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match in floor over and including 15mm thick cement screed bed of CM (1:6) complete all as specified & directed.

M & L for Vitrified tiles 10mm thick (square/rectangular) area of each tile not exceeding 0.36 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick rendering in CM 1:4 on brick wall complete all as specified & directed.

Material & labour Non skid coloured Joint free tiles 7 to 8 mm thick ( square/rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm ,in floors etc.set and jointed in neat cement slurry and pointed in white/coloured cement to match in floor over and including 15mm thick cement screed bed of CM (1:6) complete all as specified & directed.

PCC 1:3:6 C-2 (using 40 mm graded crushed stone aggregate) as in plinth protection (75 mm thick) laying in alternate ways cutting grooves and filling bitumen mastic mixed with sand and finished even and smooth without using extra cement all as specified.

M&L for granite 20 mm thick in steps, pillars, window cills, pillars, window cills, cooking platforms and like laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab incl rounding edges of stone slab one edge and including 15mm thick screed bed or bedding layer of cment mortar (1:6) complete all as specified and as directed.

S&F Sand stone slabs 5 cm thick in sun-shades, chajjas, shelves, cills, landings,cover stones, templates, etc.n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in cement mortar 1:4. complete complete all as specified and directed.

M&L for applying polymer modified primer on steel reinforcements which is a blend of portland cements, graded filters, corrosion inhibiting additive and re-dispersible polymers in powder form that when fixed with water forms slurry for application by brush to cover exposed reinforcement. The product shal achieve an adhesion bound strength of 1 Mpa to steel. It has got a pot life of 30 minutes @ 300 C. the touch dry time shall be 10-15 minutes @ 300 C. The mixed density shall be 2.01 - 2.05. The water / powder ratio by weight shall be 0.3. It shall achieve coverage of 2 kg / sqm @ 1.0 mm thickness, applying on visible reinforcement surface to from a continuous film not less than 1 mm thick complete all as specified and directed

M& L for Providing and fixing on ceiling /wall /column by duly welding MS wire mesh weighting not less than 1kg/sqm before fixing ,surface should be cleaned and should not be free from dirt ,oil grease etc complete all as specified and directed.

M&L for external plastering of brick / concrete surface of wall using fiber reinforced polymer modified repair mortar. The product shall be a single component thixotropic fiber reinforced polymer modified repair mortar needing only addtion of water at site which can be applied by trowel. It is reinforced with specially designed bean shaped, alkali resistant synthetic fibers for exceptional resistance to cracking. It is recommended for repair situations requiring application of mortar upto 18-20 mm thickness in one layer. Cement and sand can be used for finishing the surface. complete all as specified and directed.

M&L for applying two component amine cured epoxy mastic coating as bonding agent between old and new surface of wall and ceiling surface using light brush blasting using nonmetallic abrasive leaving a clean, rough and even pattern. It should be based on a 100% epoxy formulation and contains no solvents or water diluents. Apply two coats with brush or squeeze to the existing surface, working well into the substrate complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connection complete all as specified and directed.

Taking up or down 32mm bore steel tubing and connection complete all as specified and directed.

Supply and fixing 15 mm bore galvanised tubes medium grade , with all fitting and fixed complete to walls and ceilings,roofs or laid in floors.

Supply and fixing 32mm bore galvanised tubes medium grade , with all necessary fitting and fixed complete to walls and ceilings,roofs or laid in floors.

Supplying and laying 20 mm outer diameter of CPVC pipes SDR 11 icluding Plain CPVC SDR 11 including all necessary cpvc brass fittings on walls/ceiling or laying in floors complete all as specified.

Cutting chases, pinning in making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landing, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exc 10 cm girth etc brick wall complete all as specified and directed.

S&F in repairs 10 ltrs capacity PVC flushing cistern low level (white) with inlet ball valve and handle including flush pipe, brackets, rubber bush, washers etc complete all as specified and directed.

S&F in repair single piece EWC with UF seat cover hinges, fixing accessories set ,cistern fittings, rim less tornado flushiong size 360x680x750 complete all as specified and directed.

S&F in repairs oval type wash basin superior quality 537x439 mm size fitted with granite top/baroda green stone over precast RCC slab including waste coupling and suitable size bottle trap complete all as specified and directed.

S&F in repair PTMT Waste coupling (half or full threaded) . (Minimum weight 32mm- 45gms/40mm-60 gms) of 32mm bore suitable for wash hand basin and sink complete all as specified and directed.

S&F in repair 15mm bore, brass chromium plated single lever basin mixer with 300 and 600mm braided connection pipe (without pop up ) for making hot & cold water screwed down for pipe and fixed complete all as specified and directed.

S&F in repair wall mixer with provn for OHS with 115mm long bend pipe side connecting legs and wall flange, fixed in repair for 20 mm bore iron pipe or for brass ferrule fixed in repair complete all as specified and directed.

S&F 32/40 mm dia PVC waste pipe for wash basin /sinks complete all as specified and directed.

S&F in repairs 700x500mm beveled edge moulded looking mirror of 5mm thick glass mirror with double coat for protection and longevity grounded edges for safety and silver plating on the back for better reflection incl washers bolt etc. complete all asevity protection and long specified and directed.

S&F in repair PVC connection 15mm size with PTMT nuts, 600 mm long complete all as specified and directed

S & F in repair CP tubular towel rail 60 cm length of stainless steel 20 mm Dia with brackets type fixed with and including chromium plated brass screws and wooden/plastic cleats complete all as specified and directed.

S & F in repairs CP health faucet ABS body with 1.00m SS braided connection pipe, fancy type with necessary brass nuts & rubber washers, covered with chromium plated spring complete all as specified and directed.

S & F in repairs toilet paper holder with flat recessed type stainless steel, chromium plated or stainless steel with necessary brass nuts & rubber washers, covered with chromium plated spring complete all as specified and directed.

S & F in repairs CP shower rose 125mm dia alongwith long bend shower arm of length 750mm complete all as specified and directed.

S&F in repair CP soap dish brass chromium plated, size 100 x 60mm, fixed to wall with rawl plugs and chromium plated screws complete all as specified and directed.

S&F in repair 150 mm stain less steel Grade 304 square/circular grating with openable flap (Min weight 100 gms) complete all as specified and directed.

Supplied and fixed in repair set of 10 mm thick glass corner shelf set of 3 Nos ( size 200 mm,250mm & 300 mm) complete all as specified and directed.

S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S & F in repairs 20 mm bore chromium plated fancy bib taps, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair 20 mm bore CP Angle valve fancy type with wall flane, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified & directed.

S & F in repair 25mm Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed complete all as specified and directed.

S & F in repair 32 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed complete all as specified and directed.

S&F in repair 1000 ltrs capacity rotational moulded polyethylene white colour water storage tank double layered, ISI engraved (cylindrical vertical with closed top) hoisted and fixed in position incl dismantling of water tank complete all as specified & directed.

S&F in repair 25mm dia ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe 20 mm dia (minimum weight - 210 gm) complete all as specified and directed.

S & F in repair Factory Made 18mm thick 100% Solid WPC ( Wood polymer Composite ) decorative Laminated Board of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with having minimum density not less than 650 kg/cbm manufactured by Certified Company, having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compissive of 50 N/mm2 , Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free. Water/ Moisture Proof and Fire Retardant. WPC to be Laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter and fixing stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws and all required frame as per site requirement. Material test certificate and authentication should be compulsory provided by the manufacturing company : For WC/Bathroom/Toilet /Kitchen/Balcony Doors and Cabinets complete all as specified and directed.

S&F soft close cabinet hinges for kitchen cabinets/cupboards complete all as specified and directed.

S&F cupboard drawer channel set complete all as specified and directed

S&F SS wardrobe hanger rod set including all fittings complete all as specified and directed

S&F SS/Brass tie hanger set for wardrobe including All fittings complete all as specified and directed.

S&F in repair Continuous (piano) Stainless steel hinges width of flaps (when open) in 40mm, complete all as specified and directed.

S & F in repair stainless steel 40mm dia decorative knob brass polished for kitchen cup board complete all as specified and directed.

S & F in repair Brass magnet catcher suitable for CB/cabinet shutter complete all as specified and directed.

S & F in repairs 75x125mm dia of PVC (SWR) floor trap, plain with grating incl jointing with solvent cement complete all as specified and directed.

S & F in repairs 125/110 mm dia of PVC (SWR) Gully trap, plain with grating incl jointing with solvent cement complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n. exc 1.5 Sqm each complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.5 Sqm but not exc 4 sqm each complete all as specified and directed.

M&L for Factory made WPC (Wood Polymer Composite) Double Rebated frame of solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65x125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length and hinges complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made etc complete all as specified and directed.

Supply & fixing factory made 30mm thick flush shutter solid core construction with block board and plywood face panels commercial type on both side complete all as directed.

Supply & fixing Glazed or skeleton factory made door shutter, 35mm thick of second class hard wood (hollock), open rebated and prepared to receive glass, gauge ( without sash bars) with plain, chamfered or rounded, mitred beads for glass etc , size of members of shutters shall be as specified in SSR Part I, section -8 clause 8.24 (a) complete all as specified & directed.

M&L for two coats of synthetic enamel paint (Ordinary tint) over a coat of pink primer including preparation of new or previously untreated surfaces of wood of any description not otherwise described over 10cm in width or girth complete all as specified.

S&F for 200mm long brass tower bolt complete all as specified and directed.

S&F for 150mm long brass handle, oval type, stove enamelled complete all as specified and directed.

S&F for 100mm long bright finished brass mortice latch and lock 6 levers with and pair of lever handles of approved quality with necessary screws, complete all as specified and directed

S&F for 300mm long brass sliding door bolt complete all as specified and directed.

S&F for 150mm long brass floor door stoper complete all as specified and directed.

S & F for factory made solid PVC moulded door shutter door shutte,28 to 30mm thick (styles), with 2,4 or 6 raised panel design with 2mm thick 3D wood grain moulded PVC sheet on the front face & 2mm prelam PVC sheet on bach face at site as per specification & drawing with wood free EPS complete all as specified and directed.

Supply & fixing hasp and staple of size 75 mm long, safety type of aluminum anodized complete all as specified & directed.

S&F for 75mm long stainless steel Butt hinges complete all as specified and directed.

S&F for 250mm long aluminium sliding door bolt complete all as specified and directed.

S&F for 100mm long aliminium handle, cast type complete all as specified and directed.

S&F for 150mm long aluminium tower bolt complete all as specified and directed.

S & F Mild steel Angles, bars, flats etc., as in supports for stiffening of fencing, wall ties, hold fasts, clamps, plain angle cleats for securing purlins and similar small articles confirming to Fe 290 complete all as specified and directed.

S&F powder coated anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc (minimum thickness of powder coating 50 micron) weighing 0.55 Kg/M or frame size as per ground requirement complete all as specified and directed.

S&F powder coated of any colour (thickness or powder coating not less than 50 micron)anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 Kg/M including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 No.) suitable handle (1 no.)complete all as specified and directed.

S & F Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed

S&F 3 mm thick sheet glass, ordinary quality, frosted on one side for window/ventilators in square not exceeding 0.50sqm each pane complete all as specified & directed.

S&F in repairs Stainless steel drapery rods, 20mm internal diameter including decorative type brackets and PVC curtain rings 8 Nos per RM including fixing arrangement with drilling holes in walls, brackets etc complete all as specified and directed.

M & L for applying two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surface of stress over 10 cm width or girth, not otherwise described complete all as specified and directed.

M&L for demolition of reinforced cement concrete of any description and in any position complete all as specified and directed.

M&L Reinforced cement concrete (Nominal mix) Type B0 1:2:4(12.5 mm graded aggregate) Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. Note :- Reinforcement shall be measured and paid separately.

M&L for providing pre-cast cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in cover (for manholes and drains) including necessary form work set in CM 1:6 with and including demolition complete all as specified and directed. Note :- Reinforcement shall be measured and paid separately.

M&L Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with cli complete all as specified and directed.

M&L Mild steel TMT bars 6mm to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with cli complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping rough finished surfaces of concrete flat. complete all as specified and directed.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide rough finished surfaces of concrete complete all as specified and directed.

S&F in repairs 100 mm bore cast iron soil, waste vent sand cast pipes in any length with or without ears, with cement joints fixed to walls including making good disturbe portion to match the existing complete all as specified and directed.

S&F in repairs 100 mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) fitted with oval access doors and cement joint including making good disturbed portion to match the existing complete all as specified and directed.

S&F in repairs 100 mm bore cast iron branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches fitted with oval access doors and cement joint including making good disturbed portion to match the existing complete all as specified and directed.

S&F in repairs 75 mm bore cast iron soil, waste vent sand cast pipes in any length with or without ears, with cement joints fixed to walls including making good disturbe portion to match the existing complete all as specified and directed.

S&F in repairs 75 mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) fitted with oval access doors and jointed with cement joint including making good disturbe portion to match the existing complete all as specified and directed.

S&F in repairs 75 mm bore cast iron branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches fitted with oval access doors and cement joint including making good disturbe portion to match the existing complete all as specified and directed.

M&L for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45X85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length and hinges complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be madeetc complete all as specified and directed.

Excavation of post holes each not exc 0.50 cum and getting out in soft and loose soils, returning, filling in and ramming earth or broken rubble mixed with earth around in layers not exc 25 cm , watering and removing surplus soils to a distance not exc 50 m and making good surfaces complete all as specified and directed..

M&L for cement concrete type C-2 1:3:6 (using 40 mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and directed.

Supply only GI chain link fencing including line wires to any type of standards, rails, straining bolts, etc. complete all as specified and directed. Note :- (i) Line wire and flat iron will be measured and paid separately complete all as specified and directed. (ii) Size of fencing as intimated by Engr-in-Charge. (iii) Board of officer conveine by accepting office to check the size and weight per sqm.

Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specified and directed.

S & F angle iron as in post and struts in fencing including embedding in concrete, cutting tops to shape as directed, drilling holes, notching for wire etc flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., simillar work confirming to Fe-290 Gde E-165 complete all as specified and directed.

S&FMild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fittedwith washers and one hexagonal or square nut, exc 5cm but n exc 10cm long and 16 to 20 mm diameter of neck complete all as specified and directed.

S&F mild steel joist channel angle or tee sections fixed independently with out connecting plates etcof gradeW(Gde-E-250)quality-B complete all as specified and directed.

S & F for providing and fixing stinless steel (Grade 304) railing made of hollow tubes channels, plates etc. including welding, grinding, buffing, polishing and making curvature (where ever required ) and fitting the same with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of floor or the side of waist slab with suitable arrangements complete all as specified and dfirected.

M & L for machine cut Kota stone slab flooring 20-25mm thick over 15mm thick screed bed in CM 1:6. laid and jointed with grey cement slurry mixed with match the shade of the slab including rubbing and polishing complete all as specified and directed. (Note:single peice for stairs)

M & L for kota stone slab 20-25 thick in riser of steps, skirting, dado and pillar laid over 10mm thick backing coat in CM 1:4 and jointed with grey cement slurry mixed with match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for preparation of new painted steel surfaces & applying one coat of synthetic enamel paint on steel surface of any description over 10 cm in width or girth complete all as specified and as directed.

M & L for cement concrete 1:5:10 type E2 (40 mm graded stone aggregate) as in foundation filling and mass concrete or sunken etc complete all as specified and as directed.

M&L for 15mm thick plastering in CM 1:4 with WPC on concrete surfaces of finishing the surface even & smooth complete all incl water proofing compound all as specified and directed.

M& L for cement concrete padding 1:2:4 type B0 (12.50 mm graded stone aggregate ) 40 mm thick in sunken of bath /toilet /Kitchen etc with and including WPC as per manufacture's instruction complete all as specified and directed.

M&L for applying in wall portion two component elastomeric acrylic polymer modified cementitious waterproofing coating,smart damp block 2k suprema or approved equivalent,having 100% elongation as per ASTM D412.resisting 5 bars hydrostatic pressure as DIN 1048,reduction to rapid chloride shall be 70 as per have food grade certificate from laboratories like CFTRI coverage is 1.5 kg/sqm the mixing ratio of the coating shall be 2 parts of powder & I part of liquid without any water addition in the mixing etc complete as per manufactures specifications.

Taking down carefully existing unserviceable copper / aluminum point wiring of any description & in any position with and ncluding taking out existing unserviceable conduits or battens of any description with sunken boxes/junction boxes and all fitting, accessories & fixtures such as switches, ceiling roses, pendants, regulators, socket, light fittings, lamp holders etc but excluding tube light fittings and making good the disturbed surface of walls, floors, ceiling etc to match with the existing surfaces complete all as specified and directed.

M&L point wiring with 1.5 sqmm multi stranded copper conductor 1100 volts. grade FRLSH PVC insulated unsheathed cable with proper colour coding drawn in including PVC concealed conduit not less than 20 mm dia medium grade with all accessories and FRLSH PVC insulated 1.5 Sqmm multi standard unsheathed copper wire for continues earth, including cutting and chasing of wall surface for laying PVC conduit and suitable size of modular sunken box and making good to the disturbed surface of wall/floor and matching with existing specifications. Connections of cable with MCB's or bus bar shall be done through proper size copper/brass thimbles complete all as specified and directed.. Note :Conduit shall be fixed on surface of roof with necessary saddles where concealing of conduit is not feasible at no extra cost for the following :- (a) One light /fan point/Exhaust fan point controlled by one switch.

(b) One 5 pin socket outlet 5 Amps on independent board

(c) One 5 pin socket outlet 5 Amps on same board

(d) One bell/buzzer point controlled by one push button on the same board with other switches or independent

(e) One light point controlled by two 2 - w a y s w i t c h e s , with cables 1.5 sq. mm size

(f) One telephone point wiring with cables 0.4 sq mm 2 core

(g) One TV socket point wiring with cables RG-6 Coaxial cable

All as per item No 124 here in before but with cable size 4 Sq mm FRLSH for one 5 pin 15/16 Amps socket out let/AC point on independent board and multistrand insulated copper earth continuity conductor of size 4 sqmm all as specified and directed.

Supply and fixing modular telephone jack RJ-11 white colour fixed in 1 M box comprising of flush metal box, inner plate and outer cover, all conforming to IS 3854:1997 with finger proof terminals with captive screws having front fixing & removing features without removing plates complete all as specified.

Supply and fixing modular TV coaxial socket outlet fixed in 1 M box comprising of flush metal box, inner plate and outer cover complete all as specified.

Supply and fixing modular switch piano single pole, one way 6 Amps 1 module, complete all as specified and directed.

Supply and fixing modular switch piano flush type 16 Amps single pole one way, one module, complete all as specified and directed.

Supply and fixing in repair modular switch piano single pole, two way 6 Amps 1 module, complete all as specified and directed.

Supply and fixing modular socket outlet 2/3 pin 6 Amps combined 2 module, complete all as specified and directed.

Supply and fixing modular socket multipurpose 3 pin 6/16 Amps combined 2 module, complete all as specified and directed.

Supply and fixing modular step type two module electronic fan regulator heavy duty 120watts 240 volts complete all as specified and directed.

Supply and fixing Modular Bell push 6A 1 module pole, one way, complete all as specified and directed.

Supply and fixing call bell, Ding dong type, 230 volts AC single pole complete all as directed.

Supplying & fixing for ceiling rose PVC Polycarbonate isolated body 62.5 x 25 mm, three terminals, complete all as specified & directed.

Supply and fixing modular cover plate with metal frame (inner and outer) 1 module for mounting switch and sockets all as specified and as directed.

Supply and fixing modular cover plate with metal frame (inner and outer) 2 module for mounting switch and sockets all as specified and as directed.

Supply and fixing modular cover plate with metal frame (inner and outer) 3 module for mounting switch and sockets all as specified and as directed.

Supply and fixing modular cover plate with metal frame (inner and outer) 4 module for mounting switch and sockets all as specified and as directed.

Supply and fixing modular cover plate with metal frame (inner and outer) 12 module for mounting switch and sockets all as specified and as directed.

Supply and fixing blank spacer plate for single module complete all as specified and directed.

Supply and fixing 20W Inverter LED batten with square profile and polycarbonate channel. Lithium Ion battery with charging time 8hours-10 hours and back up time upto 4 hours incluuding connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

Supplying and fixing 10 watt LED battan surface / wall mounted with specially designed powder coated aluminum housing, high optically efficient polycarbonate diffuser, in built electronic driver duly pre-wired upto terminal block, power consumption < 10W, luminaire lumens > 1000 lms, driver efficiency > 85%, power facor > 0.95 THD < 20% as per IEC 61000-3-2, colour temp - 6500 K Surge protection 2.5 KV, 50000 burning hrs (min) as per L 70 criteria, two stages isolated constant current operated driver with range 150 - 270 VAC and safety extra low voltage safe level < 60 VDC as per IEC standard with LM 70 & 80 certification and connecting the same to electric source with & using PVC sheathed and insulated three core copper conductor cable of size 0.75 Sqmm and fixing arrangements for fixing the light fitting, complete all as specified.

Supply and fix Decorative, wall mounting, brushed nickel finish fixture with Opal Glass diffuser suitable with 9 W LED lamp B22 base including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fixing LED building security light fitting 35 Watt 230 V AC out-door type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection, fixed to pole or wall of building with and including suitable Bracket made out of 25 mm dia GI light grade pipe, 1.00 m long bent to shape by cutting & welding as required & directed and fixed with two Nos of FI clamps 35x6 mm to be tightened with suitable size of bolts, nut and washers and including painted with two coat of aluminium paint over a coat of red oxide primer, and including connecting the fitting to electric source with & including twin twisted copper flexible wire of size 0.75 sqmm three core with suitable size flexible PVC conduit including all accessories and fixing arrangements for fixing the light fitting and writing the date of fixing on security light with permt marker complete all as specified and directed. Note:-The period of defects liability shall be 02 Years from the date of installation of security light.

Disconnecting & taking up or down existing unserviceable sub main wiring of copper/aluminium conductor of any description, any size & in any position including taking out existing unserviceable conduits or battens of any description and making good the disturbed surfaces to the existing surfaces all as specified and directed.

M&L for sub main wiring using two 2x 6 sqmm single core FRLSH PVC insulated, unsheathed stranded copper conductor cable of voltage rating upto and including 1100 Volts drawn in and including concealed PVC conduit (Medium grade) as required dia with standard accessories along-with one run of PVC(green colour) insulated , unsheathed, stranded copper conductor of size 1x 6 sqmm as earth continuity conductor connected to earth dolly complete all as specified and directed. NOTE : Two run of single core PVC cable with one run of earth conductor and conduit /batten shall be measured as one unit.

Disconnecting and taking down old unserviceable distribution boards any size any type including MCB TPN/SPN/SP etc and making good the disturbed surfaces to the existing surfaces complete all as specified and directed.

Supply & fix sheet metal enclosure MCB distribution board. Single pole & neutral 240 volts 12 way double door complete with appropriate size bus bar and neutral link incl taking down all as specified and directed.

Supply and fixing sheet metal enclosure with socket plug top and MCB single pole and neutral with two pin and earth plug top with one SP MCB 20 Amp 240 volt complete all as directed all as specified and as directed.

Supply and fixing MCB SP 1 to 32 Amp ('C' curve) having short circuit rating 10KA, 240 volts complete with connection testing and commissioning. Complete all as specified and directed.

Supply and fixing MCB SPN 40 to 63 Amp ('C' curve) having short circuit rating 10KA, 240 volts complete with connection testing and commissioning. Complete all as specified and directed.

M&L for earthing complete with galvanized earth plate electrode 600 x 600 x6mm thick burried directly in ground vertically to a depth not less than 2.25 M below normal ground level ) with top edge of the plate not less than 1.50 M below normal ground level , connected to and including galvanized steel wire 4mm dia as earth lead soldered and riveted to earth plate by means of nuts, bolts, check nuts & washers, of galvanized iron or steel with connected to test point and testing on completion including 15mm GI light grade pipe for earth lead protection from earth point to earth plate, including provn adequate quantity of charcoal dust mixed with 35 % common salt to a packed thickness of not less than 15 cm in alternate layers of charcoal and salt on all sides of earth plate with 20mm bore medium grade GI Pipe for watering,GI check nut, funnel and wire mesh with and including all necessary excavation & earth work in soft/loose soil, returning filling in, removal of surplus soil to a distance 50 metre,,PCC 1:3:6 type C-1 as in earth pit, 40 mm thick RCC cover using cement concrete 1:2:4 type B-1 reinforced with & including 8 mm dia mild steel TMT bar @ 100 mm c/c Both way with suitable handle for lifting arrangement & including form work complete all as specified and shown in electrical plate No 3 of MES SSR Part I 2009 and as directed. NOTES:- On testing, after completion of Job, if desired earth resistance is not obtained, the earthing shall be redone at without any extra cost by contractor.

Supply, fixing and connecting in repair for Electric circuits for size of 1.0 sqmm copper FRLS wire for inverter in existing conduit/casing caping complete all as specified & directed.

Dismantling, taking down exisitng ceiling fan/Exhaust fan and deposited to E/M store for re-fixing and connecting up including provision of cable from ceiling rose or connector to fan, complete all as specified and directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm complete all as specified and directed.

Supply & Fixing ceiling fans complete with blades, down rods and accessories, 230 V, 1400 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) operate with remote control and including connecting wire with new 3 core 0.50 Sqmm PVC insulated and sheathed copper conductor cable from ceiling rose & Fan hook with hanging clamp suitable size of nut & bolts and also writing MES No with black paint complete all as specified and directed.

Supply and fix in replacement electric water heater, storage type steel body with S/S inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, 02 Nos connection pipes etc also writing MES No with black paint complete all as specified and directed.

Supply, installation, testing and commissioning of indoor type wall mounting size min (680 X 1100 X 245mm), Polycarbonate CPRI approved OEM made Meter Panel suitable for 04 (four) Single phase meter. The panel shall be made of modular POLYCARBONATE THERMOPLASTIC ENCLOSURES which should be UV resistance in accordance with IEC 61439-1, clause 10.2.4: The panel type wall mounted on mounting structure RAL 7016. The meter panel should be anti-acid & anti corrosive & fully transparent Door for meter vision. Degree of protection against mechanical load should be IK08 (5 Joule) in accordance with IEC 62262. The manufacturer of panel shall submit a copy of CPRI test report in polycarbonate only degree of ingress protection IP65 in accordance with IEC 60529. The gasket should be internally embedded made of polyurethane and enclosure make. The manufacturer of board/panel shall submit a copy of type test report of a board made out of Polycarbonate thermoplastic panel in accordance with IEC 60439-1 complete all as specified and directed. Note : Re-fixed the energy meter in new meter cabinet including all necessary electrical connection. General Specification & Electrical Parameters: 4 Meter DB Ref No. 2236 / 2023(REV-1). Type of Panel: -Thermoplastic Polycarbonate. Panel Size: -680x 1100x 245mm Degree of Protection: -IP65(EN60 529) SystemVoltage:415V,50Hz,4wire+E Installation: -Indoor Floor mounting Cable Entry: -Incoming/outgoing from bottom. Finish Shade: -Enclosure & Accessories: RAL 7035 Mounting structure: RAL 7016 Incomer: 125 A, FP 35mA MCCB-01 Nos Outgoing: 40A DP 10kA MCB – 4 Nos (5-32)A, 1Phase PREPAID ENERGY METER-4 Nos (Provision Only) Terminals- 10SQMM TERMINAL BLOCK- 8 Nos 10SQMM TERMINAL BLOCK- 4 Nos