Pdg. High Mast and Street Light in Govt. College at Meham in Distt. Rohtak.

Amount

Moulded case Circuit breakers

31.12 © Supply and erection of moulded case circuit breakers on wall or on existing pedestal including bonding to earth and necessary connections

31.12 c (i) 15 amp.to 60 amp. 415 V ,10 KA 3-phase

Miniature Circuit Breaker and Isolator

31.17 Supply and erection of miniature circuit breaker / isolator 240 /415 V in the existing distribution board including making necessary connections

(a) Miniature circuit breakers of 9 KA breaking capacity

31.17a) (ii) SP MCB 6 amp. to 32 amp

31.17(a) (ii) TPN MCB 6 amp. to 32 amp

31.22 Earthing

31.22(i) Earthing with GI earth pipe 4.5 m long and 40 mm dia with masonry enclosure on the top etc. as required

31.22(ii) Extra for using salt and charcoal / coke for pipe earth electrode as required

31.22(xii) Pdg. and laying earth connections from earth electrode with 4.00 mm dia G.I. wire in 15 mm dia G.I. pipe from earth electrode as required

31.26 Supply and erection of under ground cable ,loose in existing pipe or trenches complete with necessary connections

31.26 (xxxix) 10 Sq. mm 4 Core Cable .

31.26 (xIi) Ard 25 Sq. mm 4 Core Cable

Pedestal .

31.33 Supply and erection of Godrej Almirah typeM.S.pedestal made of 50 mm x 50 mm x 6 mm angle iron frame with 3.00 mm thick M.S.sheet covering including shutters with suitable hinges and locking arrangement with Godrej type handle including round bars . The top covering should have downward overhang of 75 mm on all sides of pedestal , having two sets of water proof ventilation holes of suitable size on the sides , at top and bottom , each set containing four Nos. holes to discharge the heat produced by the current . The shutters fixed with rubber gasket of superior quality and of suitable size to make it water proof . The pedestal duly painted both inside and outside with two coats of approved paint and primary coat and its legs are embeded upto the entire depth in 1:2:4 cement concrete block , projected 75 mm all around the pedestal and and 200 mm above the ground level including the cost of all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in-charge of the work:-

31.33 (ii) M.S.pedestal of size 750 mm wide , 900 mm high , 300 mm deep and bottom totally open , duly embeded in cement concrete block of size 900 mm x 450 mm x 200 mm above ground level duly plastered with 12 mm thick 1:4 cement plaster , having a base of size 1050 mm x 600 mm x 250 mm below ground level

31.40 Supply and erection of PVC unsheathed copper conductor cable single core 1100 volts grade in pipe of suitable size excluding cost and erection of pipe.

31.40 (i) Size 1.5 sqmm ( 3/0.81 )

31.40 (ii) Size 2.5 sqmm ( 3/1.05 )

31.41 Supply and erection of Double door sheet steel enclosure distribution boards suitable for MCB's & ELCB's recessed in wall including bonding to earth complete with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work

31.41 (v) 4-way , TP&N ( Horizontal) (8+12)

31.48 Supply and erection of MS sadles and clAmp.s on wall / RCC parapit for fixing underground cable at distance of 0.60 metre centre to centre fixed by means of rawl plug including the cost of all labour and material required to complete the job in all respect

31.51 Supply and erection of MS stand made of 50 mm x 50 mm x 6 mm angle iron frame and 150cm long, 30 cm wide with MS sheet covering size 30 cm x 30 cm x 3.15 mm thick fixed on the top of board & lugs duly embeded in 1:2:4 cement concrete block 30 cm below ground level including the cost of cement sand , welding , painting & fabrication charges etc. up to the entire satisfaction of engineer in charge of work

31.67 Supply and erection of mark double walled corrugated (DWC) HDPE pipe laid 1Mtr. Below ground level including diging and refilling of earth including cost of sutiable size socket/cuppler for HDPE pipe including the cost of labour and material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of the work.

(i) HDPE pipe 63/50 mm outer dia/inner dia

31.68 Supply and Erection of Hot Dip Galvanized octagonal pole of 3mm thickness with base plate including cost of nut and bolts and all accessories as supplied by the manufacture including cost of foundation accessories etc. The foundation bolts as per manufacturer design should be hot dipped galvanized pole complete with door locking arrangement. Terminal plate consisting of 2 Nos. 100 A, 4 pole natural links including connectin etc. with suitable connecting arrangement for 2 No. MCBs/ Kit Kat including cost of R.C.C 1:1 5:3 for foundation of size 0.7M x 0.7 M x 1.8 M with minimum 8 Nos. 12 mm dia longitudinal MS reinforcement rods with rings of 8mm dia not more than 200mm C.C for fixing the pole with all labour & material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of the work

(iii) 9 Mtr. Long pole with top dia 70mm and botom dia 155mm with base plate of size 260 x 260 x 16mm

31.83(ii) Supply, installation, Testing and commissioning of 12.5 Mtr. long High Mast manufactured from B.S.E.N. 10025 or equivalent grade material in, 2 (two)section hot dip, galvanized inside and outside in single dip, suitable for wind velocity as per IS 875 Part-3 suitable for 6 Nos. Luminaire loading fullymotorized (power tool) with starter & cable complete along with standard accessories supplied by the manufacturer with 3 nos. steel wire rope doubledrum system and twin dome aviation light with LED without foundation but including cost of set of foundation nut and bolts, installation at site complete in all respect upto entire satisfaction of Engineer-in-Charge

Thickness of Top Section = 3mm (Minimum) Bottom Section =3mm (Minimum)

Top Dia = 150mm Bottom Dia = 360mm

Thickness of Galvanization Top = 65micron (Min.) Bottom = 85micron (Min.)

M.R. items

N.S - 1 Supply and Erection of LED flood light fitting of LSFO-250-CDL/60, 250 watt of Havells make or its equivalent model of Philips BVP 410 LED 210 CW HE NB FG S3 XT / Bajaj BARFEG 240 watt / Surya SCF FL 250 Watt IP66 make (As per estimate) with pressure die cast alluminium housing, IP-65 reflector and enclosed with toughened glass with all accessories as supplied by the manufacturer including cost of all labour and material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of the work

N.S - 2 Supply and erection of 32/63 Amp. 3 Phase automatic time switch of L&T make alongwith contactor of required capacity of L&T make movement controlled by precisaty quartz osciliation operation on main supply of continue to run on built in rechargeable nickel cadium cell for 150 hours in the event of power failure including cost of contractor complete in all respect upto the entire satisfaction of Engineer-in-charge of the work.

N.S - 3 Supply and erection of 0.3 KVA capacity inverter with SMF battery for aviation light in existing panel including the cost of labour charges and connections and petty material etc. for complete in all respect upto the entire satisfaction of Engineer-in-charge of work. Make of Invertor :- Lumineous / Microtek / Sukam - Make of Battery: Exide / Amron

N.S - 4 Construction of RCC foundation for 12.5 / 16 / 20 mtr. high mast complete in all respect as per the appended design including the cost of digging sand filling 6" lean concrete 1:8:16 / bricks souling, Bar binding cement concret (M-20) shuttering, fixing of foundation bolts, refilling, carrying and erection of High Mast on foundation including petty material to complete the job in all respect up to the entire satisfaction of Engineer-in-Charge of work. (Foundation bolts and template to be supplied by department).

N.S - 5 Supply and Erection of LED flood light fitting Havells Make JETA-AIRISFLS150W or its equivalent model and specifications of Wipro LF20-192-060-57XX/Phillips BVP 122 LED146 CW FLNB FG XT FC Bajaj BJFL 150W LED Make with pressure die cast alluminium housing, IP-66 reflector and enclosed with toughened glass with all accessories as supplied by the manufacturer including cost of all labour and material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of the work

N.S - 6 Supply & Erection of double arm bracket made of 40mm dia G l pipe B class lSl 1.25mtr. Long with coller pipe (Gl) 75mm dia 60 cm Long top covered with ornamental cap duly welded painted 2 coats of aluminum paints on bracket and golden paint of ornamental cap including the cost of labour and petty material etc. complete in all respect up to the entire satisfaction of Engineer-in charge of the work.

(i) double arm bracket

N.S - 7 Supply and Erection of LED street light lumanaries of Havells make ENDURA CITY LINER NEO SL 90W or its equivalent make of Surya make SLEUL 90 Watt / Philips BRP410LED091CWHEMRPCS2PUSGR LED SL 90 60E/ Halonix make HLSLD-C10-90CWL1 with die cast housing, toughened glass with all acessories as supplied by the manufacturer with all labour and material required to complete the job in all respect upto the Entire Satisfaction of the Engineer-in-Charge of the work

N.S - 8 Supply & Erection of LED flood light fitting of Havels make JETA IRI SFL 100W LED or its equivalent make of LF20-122-060-57-XX of Wipro make / BVP 122 LED 110 W Philips Bajaj BJF 100W LED / Surya (As per estimate) with pressure die cast alluminium housing, reflector and enclosed with toughened glass with all accessories as supplied by the manufacturer complete in all respect upto the entire satisfaction of Engineer-in-Charge of the work

M/S NATWADIA ELECTRICAL COMPANY

GALAXY ELECTRIC SOLUTIONS

DEVENDER KUMAR CONTRACTOR