SPL REPAIR TO BLDG NO P-207 (01 TO 04) (OR GOVT MD ACCN) OF DOGRA AND OTHER SANCTION WKS AT ITARANA MIL STN, ALWAR

Amount

Demolition of brick/stone masonry built in cement/lime mortar of any mix including all quoins pillar ashlars masonry and removal complete .

Demolition cement concrete (unreinforcement) in ground floor and paving n exc 15 cm thickness (below or above ground level) & removal complete all rubbish materials .

Dismantling Fencing of wire mesh Any type .

Dismantling posts, purlins, or any part of truss, struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground or wall.

M & L brick work with FLY ASH BRICKS {As per IS-13757 (1993) burnt clay fly ash building bricks}, (OLD SIZE BRICKS) straight or curved on plan exc 6 mtr mean radius built in cement mortar 1:6 complete .

M & L brick work with FLY ASH BRICKS {As per IS-13757 (1993) burnt clay fly ash building bricks}, (OLD SIZE BRICKS) straight or curved on plan to any radius in half brick thick wall, built in cement mortar 1:4 complete .

Demolition of cement concrete (un-renforced) in ground floor and paving. N exc. 15 cm thickness (below or above ground level.) & removal of rubbish material complete.

Dismantling of stone slab and tiles of any description or thickness in floors, aprons etc laid, beded and pointed in any mortar including removing the dismantled material complete .

M&L for Granite (of any type) tiles 18-20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixure of pigment to match the shade of granite stone including cutting and polishing types and over screed bed 20 mm thick CM 1:6 cement concrete complete

Taking down Chowkatts or frames with shutters ( without taking off shutters from the frame exc 1.5 sq. m but n exc 4 sq m each.

Taking down Chowkatts or frames with shutters ( without taking off shutters from the frame n. exc 1.5 sq. m each.

Taking down shutter of any descriptioon exc 1 Sqm but n exc 2 Sqm each.

Dismantling floor hearth or wall tiling including cement mortar bedding but not backing removing serviceable tiles to store and rubbish of the premises

M&L for PCC (1:2:4) type B-0 (using 12.5mm graded stone aggregate), 25mm thick, as in Sub base complete .

M&L for Non Skid white ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.11 Sqm but not exc 0.18 Sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6, Complete. Make : Johnson, Kajaria, AGL.

M&L Non skid white Ceramic tiles 7 to 8 mm thick in light shade(square/rectangular) polished, area of each tiles exe 0.18 Sqm but not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl 15 mm thick cement screed in cm 1:6 complete. Make : Johnson, Kajaria, AGL.

All as per srl item No 13.00 but on walls in skriting and dedo over 10 mm thick rendering in CM 1:4 complete.

M&L 75 mm thick PCC(1:3:6) type C2 (using 40mm graded stone aggregate ) as in plinth protection finished even and smooth without using extra cement complete.

M&L 75 mm thick PCC(1:4:8) type D2 (using 40mm graded stone aggregate ) as in sub base of floor finished complete all as specified.

M&L Glazed ceramic coloured tiles in vertical surface 300X450X7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of the tiles and over 10 mm thick rendring in cm 1:4 complete. Make : Johnson, Kajaria, AGL.

M&L Green Marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete .

Taking up or down 15mm steel tubing and connections, complete all as specified and directed.

S&F steel tubing medium grade 15mm bore with all fittings fixed complete to wall and or laid in floor.

Taking up or down 20mm steel tubing and connections, complete all as specified and directed.

S&F 20mm GI tubing Medium grade fix to wall/floor complete .

Dismantling/demolition water tanks of capacity exc 250ltr but not exc 500ltr and removing from site complete .

Dismantling of 110mm bore PVC(SWR) drain pipe alongwith fittings and accessories jointed in cement mortar and taking out from walls, floors or from trenches, if required complete.

Dismantling of 75mm bore PVC(SWR) drain pipe alongwith fittings and accessories jointed in cement mortar and taking out from walls, floors or from trenches, if required complete .

M&L Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification.

S&F factory made solid PVC Moulded door shutter 28 to 30mm thick (Stiles) with 2,4 or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on front face & 2 mm plain colour PVC sheet on back face, supplying and fixing in frame at site as per specification and directed.

S&F 35mm thick IInd class hard wood factory made panelled door shutter(two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. the size of rail and stiles as per IS: 1003 (part-I), kiln seasoned and chemically pressure treated and fixed to chowkats complete.

S&F 35 mm thick 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.24 (a); supplied and fitted to chowkats complete.

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperature 1.18mm and fixed tinned tacks or GI wire stampe or nails and screws .

M&L for preparation of new wooden surfaces over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete.

S&F Butt hinges 100mm long medium weight, stainless steel complete.

S&F 150mm Aluminium, anodised, barrel tower bolts of extruded section and fixed complete.

S&F 150mm 'D' type Aluminium handles, anodised complete.

S&F 150mm extruded aluminium alloy handles ,fabricated type anodised all as specified.

S&F exctruted aluminum alloy with galavanisied mild steel hing pin Butt hinges 100mm long type B-21 .

S&F aluminium anodised barrel tower bolt 200 mm long extruded section and fixed

S&F aluminium alloy anodised sliding door bolt with hasp and staples type, 300mm long bolt type and fixing clips of sheet,cast or extruded sections and fixing bolts and sliding bolts of extruded sections fixed all as specified.

S&F 150mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring. Fixed in floor complete all as specified and directed

M&L for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings, cooler stands (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete confirming Fe 410 (Gde E-250 quality A) & making good the floor in PCC 1:2:4 type B-0 to match the existing floor.

M&L for flat iron as in hold fast, hooks, cleats welded to angle iron door/window frames etc complete all as specified and directed

S&F anodised aluminium powder coated (Mimimum thickness of powder coating 50 micron) frame for doors, windows, ventilators, with one or more rebates including joining cleat for fixing etc complete .

S&F aluminium powder coated (Mimimum thickness of powder coating 50 micron) window and ventilator shutters, side hung type without sash bars, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws,anodised aluminium fitting such as peg stays 150 mm long (01 Nos),hinges type B-1 100 mm long (2 nos) suitable handle (1 no) complete all as specified complete.

S&F Sheet glass, ordinary quality, in squares exc 0.5 sq. m each pane 5.5 mm in thickness complete.

Preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer .

Cutting holes in brick/stone walls n. exc. Half brick built in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required all as specified and directed

S & F mild steel cupboard shutter with frame, Godrej pattern made out of 22 guage mild steel sheet including chromium plated MS handle with proper locking arrangement (brass mortice lock vertical type size 65mm 4 lever with escutcheon plates & two keys) with & including two coats of spray painting with synthetic enamel paint of approved tint over a coat of red oxide primer including fixing with 6 Nos 12 mm dia bolt 150mm long grouted in brick wall/concrete including making good the disturbed surface as original complete . Note :- The measurement shall be taken of front elevation and not girthwise.

S&F in repairs 25 mm dia stainless steel curtain rod complete with SS brackets as required at site and SS side caps fancy type fixed in position by drilling holes in walls and fixed the brackers with rawl plug and steel screw compete .

M&L Plain cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in landing, chajjas, shelves and similar articler as directed including necessary scaffolding complete.

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete.

Ditto- all as per item above but 6 to 8 mm dia TMT bars.

Taking down cement plaster any description on brick or stone any description complete.

M&L Rendring 10mm thick in CM 1:6 on brick work or concrete surfaces fair faces of brick work & surfaces finished even and smooth without using extra cement all as specified.

M&L for rendering 15mm thick in CM 1:4 on brick or concrete wall surfaces fair faces of brick work & surfaces finished even and smooth without using extra cement with water proof compound ( water proof compound paid seperatly) all as specified.

M&L rendering 5mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & fair complete

Supply only Integral waterproofing compound

M & L for preparing newly plastered surfaces of wall and applying two or more coats of 100 % premium acrylic emulsion Paint having VOC less than 50gm/litre and UV resistance as per IS 15489:2004 ,Alkali and fungal resistance dirt resistance ,exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre / 10 Sqm over and including priming coat of Exterior primer @ 0.9 litre /10 sqm over 1mm thick Birla white wall care putty.

M & L for complete removal of existing treated surfaces of wall and applying two or more coats of 100 % premium acrylic emulsion Paint having VOC less than 50gm/litre and UV resistance as per IS 15489:2004 ,Alkali and fungal resistance dirt resistance ,exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre / 10 Sqm over and including priming coat of Exterior primer @ 0.9 litre /10 sqm over 1mm thick Birla white wall care putty.

M&L for preparing newly plastered surfaces and applying two coats of Oil bound distemper over a coat of alkali resistant primer on walls including 1 mm thick wall putty complete.

M & L for complete removing of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salt, trading oil greasy spots etc on old decorated surfaces of wall and applying two coats of oil bound distemper of approved shade/tint over and inclucluding 1 mm thick Birla white wall care putty complete .

M&L for preparation of new plastered surfaces of walls and applying three coats of white wash complete all as specified.

Material and labour preparation of newly plastered/unplastered surfaces of ceilings & applying three coats of white wash complete all as specified.

Material and labour complete removal of existing treatment of ceilings & applying two coats of white wash complete all as specified.

S&F in repair PVC connection pipe, 15mm dia & 600mm long with adopter and washer at both end complete.

S&F Rotational moulded polyethylene water storage tanks of 500 Ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete .

S&F in repair ball valves brass high pressure with polythelene float and fly net complete, screwed , iron pipes 15 mm dia complete .

S&F in repair fancy type bib taps, chromium plated alloy with crtuch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule and fixed bore in dia 15mm complete .

S&F in repair white vitreous china wash hand basin 'Flat back' of size 450x300mm fixed on and including new brackets CP waste coupling and PVC Waste pipe complete.

S&F in repair stop valves,fancy type, chromium plated alloy screwed down high presure, screwed both ends for iron pipe or for unions of 15 mm dia long sunk concealed type complete.

S&F in repair Stop/angle valves,fancy type, chromium plated alloy screwed down high presure, screwed both ends for iron pipe or for unions of 15 mm dia complete.

S&F in repair 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed complete. .

S&F in repair PVC waste pipe of 32mm bore of suitable length for WHB/Urinal/sink complete .

S&F in repair Soap dish, any type, fixed to plugs with chromium plated brass screws complete.

S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete.

S&F in repairs sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete.

S&F in repairs, vitreous China squatting pan, 'Orissa' pattern, size 580 x 440 mm, white with integral foot rest and 'P' or 'S' trap, including provision of Cement concrete bedding, connection to trap and Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level etc complete including making good to disturbed surfaces of floor to match with existing surface all as specified and directed.

S&F in repairs PVC low level flushing cistern 10 litrs capacity (white ISI marked) with inlet ball valve, float and handle, syphonic action type including brackets fixed in repairs, complete .

S&F 15mm dia CP pillar tap fancy type cast copper alloy, CP with capstan head, screwed down high pressure, with or without lettered 'HOT' or 'COLD' with long screwed shank and fly nuts screwed for iron pipe and fixed complete.

S&F in repair brass chromium plated shower rose 125mm size with swivel joint type including fixing to steel pipe of 15mm bore or union complete all as specified.

S&F in repair Tubular towel rail, 20mm dia, D type, 60cm long between flanges of Brass chromium plated complete.

S&F in repair Stainless steel plate rack 1mm thick of size 900mm x 900mm x 250mm including fixed with rawl plug and screws on walls complete.

S&F PVC (SWR) pipes 110 mm bore single socketed in any length with rubber ring joints fixed to walls/floor complete .

S&F PVC (SWR) bends any radius 110 mm bore complete .

S&F PVC (SWR) vent cowl 110mm complete .

S&F PVC (SWR),110mm junction single, (Single T) equal or unequal complete all as specified .

S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors/walls and making good the disturbed surface as per existing complete .

S&F in repair PVC (SWR) bends 75mm dia any radius complete all as directed.

S&F PVC (SWR) bends 75mm dia any radius complete all as directed.

S&F in repair Grating doom 100 mm dia of PTMT (Minimum weight 25 gms) fixed with cement complete .

S&F in repair 75mm dia PVC (SWR) floor trap plain with grating including jointing with solvent cement complete.

S&F in repair PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete.

Dismantling of old app membrane on roof surfaces in cluding removal of loose old plaster for receiving new plastering complete.

M&L screed laid 15mm thick in CM 1:4 with water proofing compound over green concrete surface(WPC will be measured and paid seperately) surface finished even and smooth (without using extra lime or cement) .

M&L for PCC 1:2:4 type B0 (using 12.5 mm graded crushed stone aggregate) as in roof padding, laid to a minimum consolidated thickness of 25 mm as leveling course, laid and compacted in min slope 1:30 over roof complete .

S&F APP based polymeric membrane not less than 3mm thick, weighing not less than 3.5 Kg/sqm , reinforced with polyster non-woven fabric (weighing not less than 150 gm/sqm . It shall be laid by torch application,side overlaps shall be 75mm and the ends shall be 100mm and all over laps shall be sealed by torch application including applying a coat of cold applied bitumen primer conforming IS:[email protected]/sqm and Two coats of aluminium paint over APP membrane surface complete.

M&L for 25mm thick Sand cushioning under floors complete all as specified and directed.

M&L 60mm thick machine pressed precast conctete interlocking rubberized paver block with grey cement and pigment any shape and size confirming to IS 15658-2006, M-35 Grade complete .

M&L Plain cement concrete 1:3:6 type C-1 (using 20 mm graded stone aggregate) set in cement mortar 1:4 as in kerb blocks with plain fair faces including chamfered weathering throating etc complete.

Cutting holes in brick walls Exc half brick but not exc one brick built in cement mortar or cement lime mortar and stone walls built in lime mortar etc for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B1 as required .

Demolition of reinforced cement concrete of any description and in any position (reinforcement cut as required to facilitate demolition) all as specified & as directed.

M&L for Precast RCC (1:2:4) type B-1 in manhole/soack well/septic tanks slabs/covers etc including necessary form work complete set in cement mortar 1:6 complete.

M&L for RCC (Nominal mix) in chajjas, kitchen shelves Type B1 1:2:4 (20mm graded stone)

Form work to chulla hoods, chajjas, troughs, kitchen slab and similar items including edges and fair finished surfaces.

M&L Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 or E-165

M&L for Rough cast plaster on exterior walls applying the under coat of cement and sand mortar 1:3 not less than 10mm thick and while it is still in plastic state the roughcast mixture consisting of crushed stone or fine gravel aggregate (size between 6 to 12mm) mixed with coarse sand and cement in the ratio of 1:1:1 shall be applied and finished even .The mix of cement and sand shall made slightly wetter than normal for rendering to ensure that larger aggregate are thoroughly covered complete.

Excavating in post holes (or similar) each n. exc 0.5 cum getting out returning filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25 cm as in soft/loose soil complete all as specified and directed

Excavation in trenches not exc 1.5m wide and not exc 1.5m deep for foundation or for shafts, walls, manholes etc not exc. 10 Sqm on plan and getting out in soft/loose soil.

Surface excavation n exc 30cm deep and averaging 15cm deep in any type of soil

M&L for 100mm thick PCC B-2, 1:2:4 (40mm graded aggregate) complete all as specified and directed.

M&L for 75mm thick PCC C-1, 1:3:6 (24mm graded stone aggregate) as in plinth protection complete all as specified and directed.

Returning, filling in, including spreading, leveling watering and well ramming in layers not exc 25 cm thick in soft/loose soil.

Removal of excavated soil/ material to a distance not exc 50 metre and depositing where directed at a level not exc 1.50 metre above the starting point complete all as specified.

Removing surplus excavated soil to a distance n.exc 50 metre and n exc 100 metre and depositing where directed at a level n.exc 1.5 m above the starting point.

Demolition and breaking up 150 mm bore drain pipes, salt glazed stone ware set in cement mortar including PCC haunching and bedding, complete.

M&L for 150 mm bore reinforced concrete pipe, class NP2, laid and jointed (in CM 1:1) complete with collars including forming cradles all as specified & as directed

M&L for PCC 1:4:8 type D-2 using 40 mm graded crushed stone aggregate in bedding to SGSW/NP2 drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested complete for 150 mm bore pipe all as specified and as directed.

M&L for providing and injecting chemical emulsion for post constructional anti termite treatment alongwith the external wall below concrete or masonry apron using chemical emulsion at the rate of 2.25 litre peri linear meter incl drilling and plugging 12mm dia holes with CM 1:2 to match the existing floors drilling and plugging holes etc all as specified and directed

M&L for providing and injecting chemical emulsion for post constructional anti termite treatment of soil under existing floor using chemical emulsion 300mm apart incl drilling and plugging 12mm dia holes with CM 1:2 to match the existing floors using emulsion @ 1 litre per hole complete .

Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around .

M & L for writing letters or figures (Block, Roman, Itslic or Indian) n. exc 30 cm height with thick synthetic enamel paint. complete all as specified and as directed by Engr- in - Charge.

S & F for Pipe Supporting Clamping - Single Pipe of dia 3" (75 mm/110mm) down take pipe fixing done with Clamping System consists of Profile Bracket + Continuous Slotted C Channel + U Bolt R/M System running vertically with wall distance 3": Pipe Support Clamping made of 1. Profile Bracket having Wall Distance 3" made of Low Carbon Hot Roll Gauge Corrected (HRGC) Steel (IS 1079 DD); material size 32 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result above 2000 hrs with SS304 Hex Flange Bolt with Serration 5/16 x 3/4 (A/F 13mm) as per DIN 6921and SS304 Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration as per DIN 6923. 2. Continuous Slotted "C" Channel with ribs to be used of size 10" made of Low Carbon Hot Roll Gauge Corrected (HRGC) steel (IS 1079 DD) are Hot Dip Galvanzied + Zn Al Flake coated with material thickness of 3mm. 3. U bolt R/M are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set as per DIN 6923 - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 DD used as per MTC confirms to EN 10204 3.1. Material Qty. for one unit : 1. Profile Bracket Wall distance 3" - 2 Nos. 2. Continuous Slotted C Channel of Size 10" - 1 No.; 3. U Bolt R/M for 3" (75 mm) CI or PVC Pipe Dia. - 1 No.; and 4. Justi Khilla 2 1/2" Zn coated - 4 nos. Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in the Technical Drawing No. : CE Jaipur Zone - Jaipur; TD/2022/102. Make: Shaivi or equivalent as approved by GE.

S & F for Pipe Supporting Clamping - Single Pipe of dia 3/4" (20 mm) down take pipeline fixing done with Clamping System consists of Mono Bracket + U Bolt R/M system running vertically with wall distance 3": Pipe Support Clamping made of 1. Mono Bracket for 3/4" (20 mm) pipe having Wall Distance 3" made of Low Carbon Hot Roll Gauge Corrected (HRGC) Steel (IS 1079 DD); material size 48 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result above 2000 hrs. 2. U bolt R/M are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 DD used as per MTC confirms to EN 10204 3.1. Material Qty. for one unit: 1. Mono Bracket for 3/4" pipe, Wall distance 3" - 1 Nos. 2. U Bolt R/M for 3/4" (20 mm) GI / UPVC/ CPVC pipe Dia. - 1 nos and 3. Justi Khilla 2 1/2" - 2 nos. Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in the Technical Drawing no. : CE Jaipur Zone - Jaipur; TD/2022/102. Make : Shaivi or equivalent as approved by GE.

S & F for Pipe Supporting Clamping - Single Pipe of dia 1/2" (15 mm) down take pipeline fixing done with Clamping System consists of Mono Bracket + U Bolt R/M system running vertically with wall distance 3": Pipe Support Clamping made of 1. Mono Bracket for 1/2" (15 mm) pipe having Wall Distance 3" made of Low Carbon Hot Roll Gauge Corrected (HRGC) Steel (IS 1079 DD); material size 48 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result above 2000 hrs. 2. U bolt R/M are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 DD used as per MTC confirms to EN 10204 3.1. Material Qty. for one unit: 1. Mono Bracket for 1/2" pipe, Wall distance 3" - 1 Nos. 2. U Bolt R/M for 1/2" (15 mm) GI / UPVC / CPVC pipe Dia. - 1 nos and 3. Justi Khilla 2 1/2" - 2 nos. Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in the Technical Drawing no. : CE Jaipur Zone - Jaipur; TD/2022/102. Make : Shaivi or equivalent as approved by GE.

Treatment for sunken portion is as follows:- M&L for water proofing treatment in sunken floors as described hereunder:- 1) Demelotion of lean concrete and other type of filling in sunken portion & cleaned the sunken portion incl vertical wall surface complete as directed. 2) PCC (1:2:4) type B0, covered filling in sunken portion 75mm thickness shall be provided at the junctions of RCC slab and adjoining walls. 3) Sunken floor and sides upto finished floor level shall be plastered with 15mm thick plaster in CM 1:4 wixed with WPC@ 3% by weight of cement. 4) Applying bitumen primer of sunken floor & side surfaces TANKMASTIC of M/s STP Ltd @ 0.40 ltr/Sqm. 5) Sunken portion shall be filled with lean concrete (1:5:10), Type E-2 using 40mm aggregate after carring out of satisfactory testing of CIpipes/Joints & Slab/walls by filling water 72 hrs. The sunken portion of Nahani trap/floor trap and pipes, joints shall be emmbeded in PCC (1:3:6) blocks 6) GI Spout pipe 32mm dia and 450mm long cross cutted ends shall be inserted at the time of repair to Sunken portion as directed. Note:- i) In case any defect is noticed the portion shall be grouted with cement slurry mixed with suitable chemical & tested again. This process of grouting and testing shall be repeated till leakage/seapage/dampness is elimaneted ii) Horizontal flat area only measured. iii) Above aspets are deemed to be included in quoted rate.

M&L cement concrete type C-2, 1:3:6 (40 mm graded aggregate) in foundation filling mass concrete for post holes etc complete all as specified and directed.

S&F mild steel posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 .

S&F mild steel bolt purpose made with hexagonal or square head one end screwed the other end or screwed both ends each screwed to be fuitte3d with washer and one hexagonal or square nuts exceeding 5cm and n exc 10 cm long dia of the shank 11 to 15 mm.

Fixing only chain link fencing including line wire any mesh size and type to any type of standards rails, straining bolts etc inlcluding provision of binding wire

Supply only chain link MS galvanised fencing any size or type

S&F mild steel MS round bar 10 mm dia and over cut to length bent to shape required including cranking bending hooking etc and binding with MS wire 0.9 mm dia (annealed)

M&L prepration of New steel Surfaces of any description, n.exc 10cm in width or girth and applying two coats of synthetic enamel paint when unconnected with other painting or when painted in a different tint over a coat of zinc chromate primer.

Preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer .

M&L PCC (1:4:8) type D-2, using 40 mm graded stone aggregate in fdn mass concrete.

M&L for hard core of broken stone or boulders of gauge n.exc. 63mm deposited spread and levelled in layers n.exc. 15 cm thick watered and rolled/ rammed to a true surface complete all as specified and directed.

M & L for brick work with sub class B bricks, straight or curved on plan to any radius in old type brick thick walls, built in C M in 1:4.

M&L Pre-cast (Factory casted) cement concrete Kerb stone casted in PCC (1:2:4) Type B-1 using 20mm graded stone aggregates with plan or interlocking joints (as directed) with solid blocks, exc. 10 cm in width and setting and jointed in cement mortar 1:6 complete.

Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes,channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement

M&L for prepreation of new stone/concrete surfaces and applying two coats of synthetic enamel paint of any description over 10cm girth or width not otherwise described

S&F of readymade Dholpur stone Ashok stambh with a base diameter of 0.30 meters and a height of 0.60 meters fixed over a Dholpur stone pillar with a diameter of 0.3 meters and a height of 2.10 to 2.40 meters (7' to 8') above the finished floor level ,completed all as specified and directed .

S& F galvanised, 2 strand, steel barbed wire 2.24 mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured)

M & L for treating ends of posts, backs of chowkhats, etc., area tarred exc. 0.1 Sqm but n.exc 0.5 Sqm each complete all as specified and directed.

M&L for preparing new steel surfaces of any description width or girth exc 10 cm applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer all as specified.

All as per item No 146.00 above but n.exc 10 cm width or girth

100 mm dia cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-I smooth finished and reforming benching as required complete all as specified and directed.

S&F 1000 Ltr capacity of rotational moulded polythylen water storage tank (Cylindrical vertical with closed tap) hoisted and fixed in position including S&F 20mm float valeve 20mm dia GI pipe medium grade washout pipe 450mm long with plug and 20mm dia GI pipe medium grade overflow pipe 600mm long with fitting and including dismantling of tank complete all as specified and as directed

S&F pre-painted galvalume zinc coating GI based corugated steel sheet 0.5mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed

M&L roof trusses (framed), trussed, purlins, crane gantries, rails and fastenigs and hevay bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, wind ties etc grade Fe-410-W quality A

S&F for plain cement concrete (1:2:4) type B-2, (using 40mm graded stone aggregate) in foundations, filling, mass concrete etc. complete all as specified and directed.

S&F for rolled mild steel plates (plain or chequred) channels, square cut or notched (Ordinary and counter sunk) forming holes, with out any attachment conforming to Fe 410W (Gde-E-250) quality A complete all as specified and directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1Cement:3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

M&L for preparing new concrete surfaces, stone, kerb stone surfaces of any description not otherwise over 10cm width or girth and applying towo coats of synthetic enamel paint over a coat of primer complete all as specified and directed.

Taking down carefully copper/Aluminium point wiring for light/fan/socket/light fitting/power point and taking down of teak wood batten / PVC casing caping/PVC conduit/steel conduit and making good disturbed surfaces of walls/ceilings /floors etc incl dismentling of fittings.

M&L for point wiring complete with 1.5 Sqmm single core multistranded copper conductor fire resistant low smoke (FRLS) PVC insulated and unsheathed cable 1100 Volts grade confirming to IS-694 drawn through non metallic rigid PVC heavy duty conduit in concealed (min 20 mm external dia) but shall be increased as per actual site requirement in accordance with clause No. 19.125 of SSR Part-I ISI marked with wall thickness not less than 1.8 mm including conduit accessories like bends, tees, junction boxes etc fixed concealed/recessed in wall or ceiling including 1.5 mm FRLS PVC insulated unsheathed copper earth wire including sunken type pressed steel terminal boxes electro plated of suitable size with bakellite white/coloured top sheet cover 3.0 mm thick for one light point controlled by one way switch including cutting chasis all as specified & directed.

All as per srl item No. 157.00 here-in-before but for one fan point controlled by one switch and regulator

All as per srl item No. 157.00 here-in-before but for one exhaust point/Fresh Air Fan Point controlled by one switch .

All as per srl item No. 157.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on same board.

All as per srl item No. 157.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on independent board.

All as per srl item No. 157.00 here-in-before but for one bell/buzzer point controlled by one bell push

All as per srl item No. 157.00 here-in-before but for one light point controlled two ,two way switches

All as per srl item No. 157.00 here-in-before but for one 3 pin 15/16 Amps socket outlet controlled by one 15/16 Amps switch on independent board with 2.5 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade including 2.5 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour.

Supply and fixing switch piano, flush type, single pole, one way, 5/6 Amp, 230 Volts.

S&F switch piano flush type single pole two way 5 Amps 230 Volts .

S&F bell push flush type 5 Amps 240 V complete all as specified & directed.

S&F bell/buzzer AC 230 volts single pole complete all as specified & directed.

Supply and fixing switch piano, flush type, single pole, one way, 15 Amp, 230 Volts.

Supply and fixing socket outlet, 3 pin (with 2 pin outlet also), 5/6 Amp, flush type, 240 Volts.

Supply and fixing socket outlet, 2 in 1, 3 pin, 5 and 15 Amp, flush type, 240 Volts.

Supply and fixing ceiling rose surface bakelite 65mmx50mm with two or three terminal complete all as specified.

Supply and fixing stepped type electronic fan regulator, flush type and connecting up, ISI marked, 240 Volts.

Supply and fix LED batten (1.2m) made of CRCA sheet housing with a PC glossy diffisure duly prewired connection having nominal system lumen output of 2000 lumens at a minimum system efficiency of 115 lumen per watt and total power consumption not more than 20 watt including driver. it should have rated system life time of 40000 burning hours at L70 and should have a temperature of 6500 K CRI >80, thd <10 and PF>0.95 complete all as specified and directed make - Crompton Cat Part CIS-305-40-57-SL-DP-NWH, Philips Cat part BN308C LED20S-6500 L120 PSU WH, Havells Cat Part STOUTPLUS600BS20WLED840SPCWH

S&F LED type building security light of aluminium housing light luminaire 25 watt 230 V 50 Hz including all as necessary fitting accessories and LED complete all as directed. Make : Philips/Havells/Crompton

Supply and fixing lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified.

Supply and Fixing 20 watt emergency LED inverter bulb B-22 capacity with inbuilt powerful lithium battery backup of atleast 4 hours and having minimum two years warranty. The lighting shall have deep discharge protection, fast charging, offering cool day light for atleast four hours in off hours. Make : - Havells/Philips/Bajaj

Supply and fixing sheet metal enclosures double door type suitable for fixing MCB's, SPN with 200 Amps rated bus bar, 8 way, 240 Volts.

S & F MCB 32/40 Amp, single pole & neutral, 240 Volt 10 KA complete all as pecified & directed.

S & F MCB 6-40 Amp, single pole 240 Volt 10KA complete all as pecified & directed.

Supply and fixing sheet metal enclosures double door type , suitable for fixing MCB, TPN with 200 amps rated bus bar , 4 way. 415 Volts with inbuilt MCCB 4 pole 63 Amp,16 KA

S&F sub main wiring on and including passing through PVC conduit in concealed (including cutting chasis) 1100 Volts grade with PVC flexible cable copper conductor unsheathed multistranded single core of size 6 sqmm and continuous earth with PVC flexible cable copper conductor unsheathed multistranded single core of size 6 sqmm of green colour confirming to IS 694/1990 including taking down existing U/S sub main wiring. (Note: Two runs of cable with one run of earth wire and one run of PVC Coundit should measured as one length)

Material and labour for earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level and connected to and including galvanized iron earth wire 4 mm dia by means of GI nuts, bolts, check nuts, washers thimbles, etc as shown in electrical plate No 3 of SSR Part-I and connection to main switch board/Test point/panel/equipment and testing on completion including excavation and earth work in any type of soil, returning filling in, and removal of surplus spoil to a distance not exc 50 metre, charcoal and salt in alternate layer 15 cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe medium grade 20 mm bore for watering and 15 mm bore 3.00 metre long GI pipe light grade for earth wire protection fixed with poles with two clamps, made from MS flat 25 mmx3mm, bolts, nuts and washers, PCC chamber (1:3:6) type C1, 40mm thick precast RCC cover 1:2:4 type B1 shall be provided on CI frame etc complete all as specified & directed.

M/L for GI pipe ( Light grade ) for protection of LT cable fixed to walls/ poles/road crossing including clamps complete of 40 mm bore

Supply and fix fresh air fan 250 mm sweep 240 vot 50 Hz plastic body complete with louvers all as specified and direted by Engr-In-Charge

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc. Old U/S Geysers will be deposited to E/M MES Store Yard.

Supply and fix ceiling fan complete with electronic type regulator , copper winding and accessories 230v 1200mm sweep BEE 5 star rated with brushless direct current motor (BLDC) including taking down old unserviceable ceiling fan and depositing to MES Store Yard complete all as specified and directed by engineer-in-charge.

supply and fix exhaust fan metal body AC single phase 230/240 V of size 300 mm sweep with louver including making suitable opening/hole in wall all as specified and directed by ebgineer-in-charge.

Supply and fixing in repair of GI water tubing IS-1239 marked, medium grade, in replacement including all necessary pipe fittings laid in trenches, on wall, under floor, under road on same or new route and making good the disturbed portion as existing and including taking down of old unserviciable pipe of the size 25 mm bore. Note :-Excavation Earth work will be measured and paid separately.

M & L for dry Sand cushioning to underground cable with screened, washed river sand, including punning gently all as specified and directed. Note: - Thickness after punning will be measured for payment.

Supply and lay burnt brick sub class `B' old size in trenches abutting each other width equal to length of brick etc complete as directed

Supply, laying and testing of cable LT XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured, electric power cable heavy duty with stranded aluminum conductor, 1100 Volts grade, of size 35 Sqmm 3.5 Core. Note:-Excavation, earthwork, will be measured and paid separately under respective items of this Schedule.

Supply and fix 2.5 Sqmm three core PVC insulated, unsheathed multistranded copper conductor cable 1100 volts grade complete all as specified and directed by Engr in Charge.

Supply and fix rigid non metallic PVC Conduit 20 mm dia exclusive of boxes, junction boxes, terminal but inclusive of all Tees, Bends, Elbows, reducers, bell mouth, tube ends and fixing accessories such as couplers, lock nuts, saddles pipe hooks etc complete all as specified and directed by Engr-In-Charge.

Supply and fix Vertical TPN DB 4 way suitable for Double Pole outgoing MCB-40 Amp-04 Nos with incoming 100 Amps, 16 KA, MCCB 4 pole-01 Nos complete with 250 Amps rated Copper busbar flush mounting, double door, proction class IP-30, IK08 complete all as specified

M&L for PCC 1:4:8 type D2 using 40 mm graded aggregate as in foundation of electric poles/struts etc including necessary form work and fair finish to exposed surface without using complete all as specified and directed. Note : Volume of poles/struts embedded in concrete shall be deducted.

M&L for PCC 1:3:6 type C2 using 40 mm graded aggregate as in coping for electric poles or for stay assy etc complete all as specified and directed.

Supply and fixing for LED 9 watt Bollard integral decorative LED Bollard with Opal acrylic and IP 65 protection complete including fixing arrangement complete all as specified and as directed. Make: Bajaj Cat Part No BGBOL 605 9W LED or equivalent in Philips/Havells/ Crompton.

Supply and fixing 170 Watt LED flood light with pressure die- cast aluminium housing, complete with all accessories, Energy saving, environmental friendly, long life, exclusive innovative die-cast aluminium IP65 flood light with high power LEDs as light source, suitable for highlighting architectural facade highmast and general purposelighting W Turo Floodlight luminaires with secondary optics made in pressure die cast housing and heat sink in aluminium extrusion and IP 66 Protection fixed in existing clamp and connecting with existing cable, including nuts, bolts and washer etc complete all as specified and directed by Engr-in-Charge. Note : Rates for T&P along with suitable nos of tradesmen to fix flood lights at high mast/Bldg/other suitable location as decided by Engr-In-Charge shall be deemed to be included in the quited rates by the contractor.

Supply and fixing 100 Watt SMD LED flood light with pressure die- cast aluminium housing, complete with all accessories, Energy saving, environmental friendly, long life, exclusive innovative die-cast aluminium IP65 flood light with high power LEDs as light source, suitable for highlighting architectural facade highmast and general purposelighting W Turo Floodlight luminaires with secondary optics made in pressure die cast housing and heat sink in aluminium extrusion and IP 66 Protection fixed in existing clamp and connecting with existing cable, including nuts, bolts and washer etc complete all as specified and directed by Engr-in-Charge

Material and labour for cross arms, bracings, supports,clamps and back plates fabricated from structural steel sections including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of paint.

Supply and fix Skid Mounted ETP of capacity 1 KL/ Day with Physiochemical Treatment of deimension 1.650 m X 0.75 m x 1.85 m including MS Structure, Skid mounted FRP Reactor Tanks(fiber Reinforce Plastic) Robust Design, rust & Mainteance free FRP construction for Long Life, PCB Complint Capable, Very compact design with No Civil work required, Light weight to easy accessible to narrow space, Automatic design for easy operation and comprisng the following :- (a Prefab FRP ETP Tank: FRP (Fiber Reinforced Plastic) DELTA (b) 1.1 Chemical Mix Tank FRP constructed tanks 5mm thick, 1.2 Tube Settier Tank Volume as suitable to ETP capacity (c) Clear Water Tank Cylindrical PVC Tank 0.3 KL SINTEX (d) MSEP SKID Box pipe Mild steel Epoxy painted DELTA equipment mount skid (e) Effluent Transfer Pump Centrifugal type, Horizontal pump. KIRLOSKAR 0.5m³/h 26mtr Head Cl body, 0.2HP, AC 220V (f) Level Controller High Quality Radar Type Float Sensor DELTA cum Controller for 220V (g) Pipe and Fittings UPVC Pipe & fittings ISTM 40 Schedule ASTRAL (Air, Submerge, Sludge) (h) Tube Media PVC UV Resistance Media MM AQUA (j) Automatic Control Panel, Controlling and Automation work for pumps, DELTA Cables and Wire Motors, Blowers, Cap. as required etc. (k) Sludge Transfer Pump CI Body, Self-priming pump. Horizontal Pump, KIRLOSKAR 0.5m³/h 10mtr Head AC 220V (l) Sludge Dry Bags Polyester bag, MS stand, etc DELTA (m) Filter Feed Pump CI Body, Self-priming, Mono Block Pump 1HP, KIRLOSKAR AC 220V (n) Air Blower Silent blower, 0.45 kg/cm², Air flow25m³/Hr., DELTA Motor-0.5 HP, 220V (o) Air Diffusers Fine and Coarse bubble diffusers as suitable to tank MM AQUA

(p) Pressure Gauges Burdon Type H Guru/Eq. Instruments (q) Activated Carbon Filter Vertical, FRP vessel, Multiport Valve, Pentair/Eq. Carbon media and piping (r) Multi Grade Sand Filter Vertical, FRP vessel, Multiport Valve, Pentair/Eq. Filter media and piping (s) PH monitor Online Digital Measuring ASTER (t) Chemical Tanks 60 LTR-LDP Chemical tank SHEETAL (u) Chemical Dosing Pumps PP Head, Diaphragm pump, 0-6 LPH, 30W, 220V E-DOSE (v) Flow meter-Turbine Inlet/Outlet of STP KRANTI (w) Multi Function Meter Energy, Volt, AMP, RPM, PF AMICI Oil & Grease Separator (x) Modular Oil Separator Bar Screen and Oil & Grease Chamber (O&G tank, Skimmer) MSEP Construction

Supply and fixing sheet metal enclosures single door type suitable for fixing MCB's, SPN with 200 Amps rated bus bar, 4 way, 240 Volts.

Supply and Laying in trenches or passing through pipe/fixed to pole/ wall XLPE insulated armoured heavy duty electric cable with alluminium conductor of 16 sqmm x 2 core size including taking out old U/S cable. Note : Excavation & earth work will be measured and paid separately under the respective items.

Material and labour of Earthing complete with GI earth plate electrode of size 600x600x6mm thick buried directly in ground (earth pit should not less than 4 mtr deep below normal ground level ) with top edge of the plate not less than 2.95 mtr deep below normal ground connected to and included GI earth strip 32mmx 6mm by means of bolts nuts check nuts and washer returning and filling the pits with excaviated vsoil mixing with charcoal 250 kg, crystal salt 200 kg ,magnisiun sulphate of 100 kg and vegitable soil all around the plate up to 350 mm above from top edge of plate and balence portion filling with excaviated soil in layers not exc 25 mm thick 25 mm bore galvanised iron medium grade watering pipe up to top of plate 50mm bore galvanised iron light grade pipe for earth strip protection including all excavation earth work in any type of soil pcc 1;3;6 type c1 ....for chamber of internal size 300mmx 300mmx300mm with 120mm thick wall and 700mmx700mmx150mm thick bed concreat RCC 1:2:4 ,type B1 for precast chamber cover 50mm thick reinforced with welded steel wire fabric orxPM jali (weight not less than 4.00 kg/sqmm) ,funnel,with wire mesh complete all as specied and directed. Note (i) Quoted rate shall be deemed to include for earth strip with protection pipe up to 7.5 M length

Supply and fixing in repair 40 Watt (Warm white) LED Post of with high aesthetics and premium looks provided with die cast aluminum housing and polycarbanate opal diffuser and IP 65 protection all as directed Make: crompton Cat Part No - CBP-610-40-30-SL-CA-NBK

Supply and fix of ^lithium based Energy Efficient Integrated solar street light of 40 watt ^ in single aluminium extruded body with duly polyurethane coating,encases with monocrystalline solar PV panel of 60 Wp ,lithium battery 11.1/12.8 v 30 AH with inbuilt BMS IP 65 high brightness W-LED (150 lm /watt) lamp with aluminium reflector for better light distrubtion CRI>70 colour temperature 5700-6500K . microcontroller basedcharge controller cum driver automatic diming function PIR motion sensor with diffirential dimming function dusk to dawn operation sutiable to working temperature -10 to 55 C .weight not more than 14-16 kg with adjustiable MS clamp sutiable for pole wall mounting etc complete as requirer protection-short circuit overload reverse polarity and battery protection firm should provide vital parameter test report from NABL accredited lab and should be made in india with CE and ROHS complaint including dismentling of old UNSV light and including bracket of 40 mm dia medium grade all as specified and directed by engineer-in-charge make-crompton cat part no-CSOP-807-40-57-HL4-PIR-LM-GG or equivilent to havells and bajaj

shiva construction (BID ID -3380986)