completion of incomplete work construction of tech building complex for LLLWR at Thoise

Amount

Schedule A Part-I (BUILDING WORK )Note: 1. This Schedule is pre priced by MES and the pre priced rate indicated under Col 5 signifies this fact only. Note: 2. Before quoting rate contractor is required to visit the site to ascertain the quality and quantity of work/ balance work / left over job. No claim shall be entertained after quoting of rate and rate quoted shall be final and binding.

Construction and completion of Left over work of block of building (Four storied) for mounting Radar with Ops and technical equipment, framed structure with RCC roof including rampsand plinth protection complete all as specified and shown on drawings For reference Ref Appendix 'A1' Note: Before quoting rate contractor is required to visit the site to ascertain the quality and quantity of work/ balance work / left over job. No claim shall be entertained after quoting of rate and rate quoted shall be final and binding.

Construction and completion of Left over work of Septic tank for 25 users complete all as specified and as shown on drawings and as directed. Note: Before quoting rate contractor is required to visit the site to ascertain the quality and quantity of work/ balance work / left over job. No claim shall be entertained after quoting of rate and rate quoted shall be final and binding.

Construction and completion of Left over work of Soakage well 3.0 mtr dia and 4.5 mtr deep complete all as specified, shown on drg and as directed. Note: Before quoting rate contractor is required to visit the site to ascertain the quality and quantity of work/ balance work / left over job. No claim shall be entertained after quoting of rate and rate quoted shall be final and binding.

Total amount of Schedule 'A' PART-I (BUILDING WORK)

Total amount of Schedule 'A' PART-II (Section-I) List of work and price cost for fire point

SCH 'A' PART-II ( SECTION-II): LIST OF WORKS AND PRICE FOR FIRE FIGHTING Note : This schedule is not pre priced by MES and the pre priced rate indicated as "Rs. 0.00" under Col.5 signifies this fact only.

Mild steel plain black sheet 4mm thick in wall cladding, steel gates and similar work, cut to size, holes punched, including round headed screws, clout nail or rivets etc, fixed to steel framing with plain 40mm lap joints with rivetd or welded seams, including, bending or turning up, mitred angles etc., complete all as specified and as directed by Engineer-in- Charge.

Total amount of SCH 'A' PART-II (Section-II) List of work and price cost for fire point

SCH 'A' PART-III : LIST OF WORKS AND PRICES FOR HARDSTANDING

SCH 'A' PART-IV : LIST OF WORKS AND PRICES FOR SEWAGE DISPOSAL

SCH 'A' PART-V( SECTION-I): LIST OF WORKS AND PRICE FOR FOR EXTERNAL ELECRIFICATION

SCH 'A' PART-V( SECTION-II): LIST OF WORKS AND PRICE FOR FOR EXTERNALL ELECRIFICATION SUPPLY Note : This schedule is not pre priced by MES and the pre priced rate indicated as "Rs. 0.00" under Col.5 signifies this fact only.

Supply, fixing and testing street light fitting 70 watt metal halide 230 V single piece pressure die cast aluminium housing with step pot optics reflecter, IP65 ingress protection and built in tilt of toughened clear glass cover for lamp & control gear compartment confirming to cat pt No SGP301 1 xSON 70 W FG for lamp 1 x SONT 70W(E) of philips or equivalent make crompton/GE complete with lamp and PVC insulated sheathed flexible copper conductor cable of size 1.0 sqmm from DB to street light all as required and directed.

Supply and fix mounting bracket for street light bend to shape as per requirement made of 40mm bore medium garde GI tubing 1.2 mtr long and clamp, nut bolts all as required at site or directed.

Blank

Total amount of SCH 'A' PART-V( SECTION-II

Total amount of SCH 'A' PART-VI (SEC-I) : LIST OF WORKS AND PRICES FOR EXTERNAL WATER SUPPLY

SCH 'A' PART-VI (SEC-II) : LIST OF WORKS AND PRICES FOR EXTERNAL WATER SUPPLY Note : This schedule is not pre priced by MES and the pre priced rate indicated as "Rs. 0.00" under Col.5 signifies this fact only.

Supplying, fixing and testingof mono block pump of capacity 1 HP 230 volts 50 HZ with all electrical connection and necessary PCC foundation as per manufacturer's instructions, complete all as specified and as directed.(Make:-Crompton/ABB/Kirloskar)

Total amount of SCH 'A' PART-VI (SEC-II)

SCH 'A' PART-VII (SEC-I): LIST OF WORKS AND PRICES FOR INTERNAL ELECTRIFICATION

SCH 'A' PART-VII (SEC-II): LIST OF WORKS AND PRICES FOR INTERNAL ELECTRIFICATION Note : This schedule is not pre priced by MES and the pre priced rate indicated as "Rs. 0.00" under Col.5 signifies this fact only.

Flourescent tube light fitting decorative Mirolta classic 1x40 watts complete with electronic ballast, with high power factor more than 0.9, concealed lamp holders, capacitor, connector block all accessories prewired with suitable size cable,conforming to Cat Part No. TMS 510 HF with end caps of make Philips or equivalent of make Bajaj/Crompton including 4',1x40 watts tube rod and connecting electrically to ceiling rose using PVC insulated and over all sheathed flexible copper conductor cable of size 0.50 sqmm 3 core-all as required at site or directed.

Surface mounted CFL luminaire mirror lighting confirming to cat part No. TLN 11 of Crompton or equivalent of make Philips/Bajaj Complete with lamp including connecting electrically to ceiling rose using cord flexible 3 core PVC insulated overall sheathed flexible copper conductor of size 0.50 sqmm, all as required at - site and directed.

Socket for telephone with top Make: Cona cat Part No. 1756 or equivalent of make Leader/SSK. Complete with CI/MS sunk box with 3mm thick plastic laminated top sheet cover all as required and directed.

Heavy duty exhaust fan 5 star rated (as per BEE recommendation) 300mm sweep, single phase, 230 volts 50Hz AC supply, totally enclosed, heavy duty motor with die cast aluminium rotor mounted on two ball bearings, complete louvers including cutting chases for fixing fan, connecting electrically using 3 core 0.75Sqmm PVC insulated flexible copper conductor cable over all sheathed all as required at site or directed by Engr-in-Charge. Make:- Khaitan/Bajaj/Crompton.

Heavy duty exhaust fan 5 star rated (as per BEE recommendation) 380mm sweep, single phase, 230 volts 50Hz AC supply totally enclosed heavy duty motor with die cast aluminium rotor mounted on two ball bearings complete louvers including cutting chases for fixing fan, connecting electrically using 3 core 0.75Sqmm PVC insulated flexible copper conductor cable over all sheathed all as required at site or directed by Engr-in-Charge. Make:- Khaitan/Bajaj/Crompton.

Ceiling fan 5 star rated (as per BEE recommendation) of 1200mm sweep suitable to work on single phase AC 230 volts 50 Hz complete alongwith supply and fixing of electronic regulator step type hum free suitable to control speed of fan 0 to 100% of Model PENTA of make Anchor or equivalent of make crompton/Bajaj, connecting electrically to ceiling rose or connector block using PVC insulated and over all sheathed 3 core cable of size 0.75 Sqmm with flexible copper conductor all as required at site or directed. Make:- Crompton/Khaitan/Bajaj.

Distribution board iron clad, double door with IP-43 1K-09 protection suitable for MCB TPN as incommer and MCB SP as outgoing 415 Volts 3 phase 50 C/s 4 way, complete with appropriate size copper bus bar and neutral link conforming to cat part No.607715 of Legrand or equivalent of make C&S/Merlin Gerin, complete including cutting chases to wall for fixing DB and making good the disturbed wall surface all as required at site and directed by Engr-in-Charge.

Sheet metal enclosure MCB distribution board, double door with IP43 1K-09 protection single phase 240 volts 8 way, including suitable size copper bus bar and neutral Ink conforming to cat part No. 607711 of legrand or equivalent of make Hager/Merlin Garin fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification.

MCB sinlge pole 240 volts 5 to 30 Amps, with rupturing capacity 10KA, "C" curve type Make: Hager, Legrand, Merlin Gerin(Multi-09).

MCB single pole 240 volts 40 Amps, with rupturing capacity 10KA, "C" curve type Make: Hager, Legrand, Merlin Gerin (Multi-09).

MCB three pole & Neutral 440 volts 32 Amps, with rupturing capacity 10KA, "C curve type Make: Hager, Legrand, Merlin Gerin(Multi-09).

MCB Single pole and Neutral 440 volts 40 to 63 Amps, with rupturing capacity 10KA, "C" curve type. Make:- Hager, Legrand, Merlin Gerin (Multi-09).

Tube light fittings surface mounting FRP body corrosion resistance with stove enameled white CRCA gear cum reflector tray complete with gasket and clear acrylic cover 1x40 watts complete with copper wound ballast, starter holder, spring loaded bipin holders, capacitor, connector block all accessories prewired with suitable size cable conforming to cat part No. BJI 136/140 of Bajaj or equivalent of make Phillips/Crompton including 4',40 watts tube rod and connecting electrically to ceiling rose using cord flexible of size 0.75 Sqmm 3 core overall sheathed. complete all as required and directed.

Lamp holder insulated body with back plate for batten fittings. Make: Cona cat part No. 2151/SSK cat part No. 571 or equivlent of make Leader including CFL 1x11 W of make Bajaj/Crompton/Helonix.

Point wiring one light/fan point controlled by one switch with 1.5 sqmm PVC insulated (FRLS) sheathed copper conductor single core multi strand flexible cable and 1.5 Sqmm PVC insulated (FRLS) sheathed copper conductor single core cable (green colour) as earth lead in and including concealed non metallic rigid PVC conduit medium grade with all fittings (ISI marked) controlled by one switch including CI/MS sunk box of required size, and as directed by Engr in charge and 3mm thick plastic laminated sheet, including cutting chases to wall making good the disturbed surfaces to match with the exising specifications complete all as specified. (Make of cable: L&T/Finolex/Grandlay).

Point wiring one light point controlled by 2 Nos two way switches with 1.5 sqmm PVC insulated (FRLS) sheathed copper conductor single core multi strand flexible cable and 1.5 Sqmm PVC insulated (FRLS) sheathed copper conductor single core cable (green colour) as earth lead in and including concealed non metallic rigid PVC conduit medium grade with all fittings (ISI marked) controlled by one switch including CI/MS sunk box of required size, and as directed by Engr in charge and 3mm thick plastic laminated sheet, including cutting chases to wall making good the disturbed. surfaces to match with the exising specifications complete all as specified. (Make of cable: L&T/Finolex/Grandlay).

Point wiring for 3 pin 5 Amps socket out let independent controlled by one switch with 1.5Sqmm PVC insulated (FRLS) sheathed copper conductor single core multi strand flexible cable and 1.5 Sqmm PVC insulated (FRLS) sheathed copper conductor single core cable (green colour) as earth lead in and including concealed non metallic rigid PVC conduit medium grade with all fittings (ISI marked) including CI/MS sunk box of required size, and as directed by Engr in charge and 3mm thick plastic laminated sheet, including cutting chases to wall making good the disturbed surfaces to match with the exising specifications, complete all as specified. (Make of cable: L&T/Finolex/Grandlay)

Point wiring for one 3 pin 15 Amps socket out let independent one flood light controlled by one switch with 2.5 sqmm PVC insulated (FRLS) sheathed copper conductor single core multi strand flexible cable and 1.5 Sqmm PVC insulated (FRLS) sheathed copper conductor single core cable (green colour) as earth lead in and including concealed non metallic rigid PVC conduit medium grade with all fittings (ISI marked)controlled one switch including CI/MS sunk box of required size, and as directed by Engineer-in-Charge and 3mm thick plastic laminated sheet, including cutting chases to wall making good the disturbed surfaces to match with the exising specifications, complete all as specified. (Make of cable: L&T/Finolex/Grandlay)

Total amount of SCH 'A' PART-VII (Section-II): LIST OF LEFT OVER WORKS FOR EXTERNAL WATER SUPPLY

SCH 'A' PART-VIII : LIST OF WORKS AND PRICES FOR INTERNAL WATER SUPPLY

SCH 'A' PART-IX ( SEC-I ) :LIST OF WORKS AND PRICE FOR FOR PLUMBING WORK

SCH 'A' PART-IX ( SEC-II ) :LIST OF WORKS AND PRICE FOR FOR PLUMBING WORK Note : This schedule is not pre priced by MES and the pre priced rate indicated as "Rs. 0.00" under Col.5 signifies this fact only.

Cast iron gully traps square mouthed type 'P' of size 150 mmX 100 mm including excavation and earth work in any type of soil, removal of surplus soil upto 50 metre, PCC 1:2:4 type B-1 in bends, surrounds, kerbs etc and cast iron equal hole grating, not less that 10 mm thick and CI cover of size 450mmX450mm, PGI sheet including jointing with cement complete all as specified and directed.

Total amount of SCH 'A' PART-IX ( SEC-II )

SCH 'A' PART - X (DEFECTIVE ITEMS OF WORKS IN RESPECT OF SCH 'A' PART -I Ser No -1) Note : This schedule is not pre priced by MES and the pre priced rate indicated as "Rs. 0.00" under Col.5 signifies this fact only.

Dismantling floor hearth or wall/stone tiling including cement mortar bedding (but not backing ) removing serviceable tiles to store and rubbish off the premises. all as specified and directed

Machine cut kota stone slab flooring/ treads of steps 18-20 mm thick over and incl 20 mm cement screed base in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the floor by picking , sweeping clean and washing down with water to remove dust, etc including moulding at edge , rubbing and polishing complete all as specified & directed .

Taking down cement plaster on brick walls of any description including racking out joints, hacking for key, scrubbing down with water etc complete all as specified.

Rendering 15 mm thick in cement mortar (1:6) on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified.

Demolition of Roofs, floors (other than ground floors), beams staircases, landing, chajjas, & similar suspended work Cement concrete (reinforced) complete all as specified.

Formwork to sides & soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors & beams, etc. Rough finished surfaces of concrete flat complete all as specified.

M&L RCC M-30 design mix using 20 mm graded aggregate in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified.

M&L Mild steel TMT bars 10mm dia & over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality complete all as specified.

M&L Mild steel TMT bars 6mm to 8mm dia,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality complete all as specified.

Total amount of SCH 'A' PART-X

M/S MOHD MUSSA (BID ID -3318332)