Loading
Loading…
Loading…
Tender Value
₹94.8 L
EMD Value
₹1.9 L
Closing Date
20 Aug 2026, 3:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
Above/Below/Par
DRAWING
15 conditions · 3 needing a document upload
Financial Eligibility Criteria: The tenderer must have minimum average annual contractual turnover of V/N or V whichever is less; where V= Advertised value of the tender in crores of Rupees. N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-F, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
Electrical License: The tenderer shall possess a valid Electrical Contractor License, issued by any State Government or Union Territory Administration, authorizing execution of electrical works up to 11 kV. The contractor shall have in his employment or shall engage a person holding a valid certificate of competency issued by any State Government or Union Territory Administration for supervision of electrical works up to 11 kV.Offers not accompanied by a valid Electrical Contractor License and requisite Supervisor competency for works up to 11 kV shall be summarily rejectedNote: In case of expiry of validity of license during contract, the contractor should renew the license so that it is always valid during contract).
Technical Eligibility Criteria: (a) The tenderer must have successfully completed or substantially completed any of the following during last 07 (seven) years, ending last day of month before the one in which tender is invited: Three similar works costing not less than the amount equal to 30% of advertised value of the tender, or Two similar works costing not less than the amount equal to 40% of advertised value of the tender, or One similar work costing not less than the amount equal to 60% of advertised value of the tender.
Definition of Similar nature of work: "Works of wiring/cabling or installation and commissioning of electrical items (other than on coaches) such as lights, fans, pumps, charging arrangements, earthing etc. (with or without supply of items / equipment) for 230V, 1phase or 415V, 3phase system or higher voltages".
9 conditions · 1 needing a document upload
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Tenderer /s are required to submit a scanned / attested copy of following information along with their tender- 1. Bank Account No 2. Name of Bank 3. Indian Financial System Code {IFSC} 4.PAN No 5. Tenderers Contact No Contractor should provide firms PAN, issued by Income Tax Department with his quote or within30 {Thirty} days of award of contract. No payment will be released without submission of PAN. All taxes including surcharge and cess shall be recovered from his payment as per tax provisions in vogue.
The tenderer shall thoroughly go through the entire tender document and strictly adhere the instructions and directions given at different pages.
It is responsibility of the tenderer that they ensure to see any corrigendum of the tender to check the corrigendum on the website from time to time.
All the required/supporting documents should be scanned and uploaded.
In case the date of closing mentioned in the Notice Inviting Tender is declared a holiday/bandh/strike etc. on any account, the date of closing tender online will not be changed as the application in the website of IREPS does not permit submission of any offer after closing date and time of the tender. However, opening of tenders online will be on any convenient day after the closing date/time of tenders.
Opening of e-tender online:- The e-tenders will be opened online using the IREPS portal. No representative is required to be present for opening of tender and taking notes of rates quoted and ranking as the complete details of rates etc. of all the bidders shall be available to the bidders in the website after the opening of the tender.
NED-Extension of Lalwadi Pit line No-1 by 03 Coaches -Electrical Arrangements
NED-E-18-2026-27
NED-E-18-2026-27
Open
Works - General
12 Months
Nanded, Maharashtra
₹0
₹1.9 L
20 Aug 2026
29 Jul 2026
6 Aug 2026
137 items across 1 schedule
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 94,84,305 | ||
| — | 500.00 | — | — | ||
| Supply of 16 W 3 directional LED cat walk light fitting (4W+8W+4W) aluminium de cast with ip 67 protection works on 24 V DC as per Specification. Note Prior Approval to be taken including all accessories. | — | — | — | 10,56,500 | |
| — | 500.00 | — | — | ||
| Erection of 16 W 3directional LED cat walk light fitting (4W+8W+4W) aluminium de cast with ip 67 protection works on 24 V DC as per Specification. Note Prior Approval to be taken including all accessories. | — | — | — | 60,000 | |
| — | 200.00 | — | — | ||
| Supply of 16 W 3 directional LED Pit Light fitting with IP 67 Protection(10W+4W+2W) aluminium die cast with IP 67 Protection as per specification. . Note Prior Approval to be taken including all accessories. | — | — | — | 4,40,800 | |
| — | 200.00 | — | — | ||
| Erection of 16 W 3 directional LED Pit Light fitting with IP 67 Protection (10W+4W+2W) aluminium diecast with IP 67 Protection as per specification. . Note Prior Approval to be taken including all accessories. | — | — | — | 24,000 | |
| — | 26.00 | — | — | ||
| Design, supply of SMPS control Panel unit containing 3 nos of 24 V 10 A SMPS power supply units enclosed in sheet steel enclosure with all necessary accesorries. .Note Prior Approval to be taken including all accessories. | — | — | — | 4,19,536 | |
| — | 26.00 | — | — | ||
| Erection of SMPS control Panel unit containing 3 nos of 24V 10 A SMPS power supply units enclosed in sheet steel enclosure with all necessary accesorries. .Note Prior Approval to be taken including all accessories. | — | — | — | 8,814 | |
| — | 3600.00 | — | — | ||
| Supply of CPVC pipe SDR-13.5 class -I pipe of size 20 mm (3/4 inch). | — | — | — | 4,53,600 | |
| — | 3600.00 | — | — | ||
| Erection of CPVC pipe SDR-13.5 class -I pipe of size 20 mm (3/4 inch). | — | — | — | 10,800 | |
| — | 700.00 | — | — | ||
| Supply of CPVC 20 mm dia (3/4 inch) Tee including fixing etc. | — | — | — | 23,100 | |
| — | 700.00 | — | — | ||
| Erection of CPVC 20 mm dia (3/4 inch) Tee including fixing etc. | — | — | — | 1,400 | |
| — | 1100.00 | — | — | ||
| Supply of metal clamp with suitable screws (length type) on concrete surface including provision of plugs with all accessories for CPVC 20 mm dia (3/4 inch). | — | — | — | 13,200 | |
| — | 1100.00 | — | — | ||
| Fixing of metal clamp with suitable screws (length type) on concrete surface including provision of plugs with all accessories for CPVC 20 mm dia (3/4 inch). | — | — | — | 1,100 | |
| — | 700.00 | — | — | ||
| Supply of cable junction box with terminals etc (size 93x93x62 mm) with IP66 integrated membrances for cable entry suitable for 20mm CPVC pipe. | — | — | — | 3,20,600 | |
| — | 700.00 | — | — | ||
| Erection of cable junction box with terminals etc (size 93x93x62 mm) with IP 66 integrated membrances for cable entry suitable for 20 mm CPVC pipe. | — | — | — | 44,800 | |
| — | 3760.00 | — | — | ||
| Supply of 2 Nos. of 2.5 Sq.mm, 1 No. 1.5 sq.mm of FRLS PVC insulated flexible multi strand copper wire including earth continuity wire . | — | — | — | 2,70,720 | |
| — | 3760.00 | — | — | ||
| Erection of 2 Nos. of 2.5 Sq.mm, 1 No. 1.5 sq.mm of FRLS PVC insulated flexible multi strand copper wire including earth continuity wire . | — | — | — | 33,840 | |
| — | 300.00 | — | — | ||
| Supply of Single core 6 sq. mm PVC insulated multi strand copper wire | — | — | — | 16,200 | |
| — | 300.00 | — | — | ||
| Erection of Single core 6 sq. mm PVC insulated multi strand copper wire | — | — | — | 2,100 | |
| — | 300.00 | — | — | ||
| Supply of Single core 10 sq. mm PVC insulated multi strand copper wire | — | — | — | 21,600 | |
| — | 300.00 | — | — | ||
| Erection of Single core 10 sq. mm PVC insulated multistrand copper wire | — | — | — | 3,000 | |
| — | 3600.00 | — | — | ||
| Cutting and chipping the wall for laying the PVC conduit pipe and plastering after laying the PVC conduit pipe with cement and sand mortar mixed with 1:8 ratio, but with out laying PVC conduit pipe. | — | — | — | 1,80,000 | |
| — | 50.00 | — | — | ||
| Supply of Thermo plastic poly carbonate box | — | — | — | 2,82,500 | |
| — | 50.00 | — | — | ||
| Erection of Thermo plastic poly carbonate box | — | — | — | 11,300 | |
| — | 32.00 | — | — | ||
| Supply and erection of earth electrode. | — | — | — | 1,26,496 | |
| — | 18.00 | — | — | ||
| Supply, fixing and installation of 32 A industrial 2P+E plug and socket with 32 A DP MCB. Make: Legrand/L&T/INDOASIAN/Schneider or similar | — | — | — | 47,160 | |
| — | 6.00 | — | — | ||
| Supply, fixing and connecting of 63 A 3P+N+E Industrial Panel Socket Box having IP 67 protection with 63A MCB as per the site conditions and as directed by site engineer. Make: Legrand/Havells/L&T/Schneider/INDOASIAN or similar | — | — | — | 48,390 | |
| — | 16.00 | — | — | ||
| Supplying of programmable digital almanactimer microcontroller based with real time clock to operate on derived switching-ON & switching-OFF street light as per daily sun setand sun rise respectively automatically having 4-digit LED continuous time display, relay output 230V/10A with 10 hrs. battery back up and manual over drive facility capable to drive different capacity contactors timer erected in provided M.S. box in an approved manner. | — | — | — | 1,00,688 | |
| — | 8.00 | — | — | ||
| Providing & erecting 5 m high (clear height) galvanized OCTAGONAL pole with foundation bolts having bottom of 130 mmA/F, top 70mm A/F on provided foundation as per specification No. OH-PL/OPL. | — | — | — | 1,01,888 | |
| — | 8.00 | — | — | ||
| Providing & casting of M - 20 grade reinforced cement concrete (RCC) foundation suitable for 3m to 5m high octagonal / conical G.I. pole considering the safe soil bearing capacity at site as 10 T/sq m at 1.5 m depth including supply of steel, concrete, excavation and fixing provided nut bolts with the help of template as per design in an approved manner. | — | — | — | 23,984 | |
| — | 8.00 | — | — | ||
| Supplying and erecting Street light bracket for erection of Double fitting made from 40 mm. dia 'B' class G.I. pipe 1.0 m in length along with pole cap of 300 mm length 100 mm dia duly welded as per specification no. FG-BKT/BPC | — | — | — | 9,160 | |
| — | 8.00 | — | — | ||
| Service connection to the fitting from the junction box of 5 mtrs Octogonal pole by means of PVC insulated copper conductor of 3 core 1.5 sq mm with necessary lugs at the junction box and necessary termination at the lumaninaire complete. | — | — | — | 3,360 | |
| — | 220.00 | — | — | ||
| "Supply and fixing of 40 W LED type weather proof street light fitting complete with all accessories and conforming to specification Make: Bajaj/Havells/ Philips or similar" | — | — | — | 5,34,160 | |
| — | 340.00 | — | — | ||
| Cutting of esphated road/ concrete/cement/under the track etc., and excavation of cable trench 30 cm wide x 90cm deep roadetc., for laying of HT/LT UG cable. After laying of cable the trench should be brought to its original position by providing tar/ concrete/cement as per the site conditions and as per directions of Rly.Engineer. | — | — | — | 76,840 | |
| — | 540.00 | — | — | ||
| Supply, fixing and laying of GI perforated cable tray of size 300 mm x 50 mm x 2 mm Thick with all connected accessories. | — | — | — | 4,55,760 | |
| — | 5.00 | — | — | ||
| "supply, erecting and connecting of SMPS Single Phase Power Supply - 100-240V Input - 24V DC Output - 100W - 4,5A Make: Schinder or similar" | — | — | — | 12,805 | |
| — | 5.00 | — | — | ||
| "Supply, fixing and installation of PANASONIC EQ34PNJ or equivalant Photo electric Sensor, EQ-30 Series, 2 m, Reflective, PNP, 10 V to 30 V. (it includes supply of sensor, plug in connector and mounting bracket ant etc..). Photo electric Sensor with PNP output, plug-in connector. Un affected by colour or material, 2m (6.562ft) distance adjustable fixed-focus sensing. Automatic interference prevention. It can be used in places splashed with water. Stability indicator -25 to 55°C Operating temperature IP67 Protection rating" | — | — | — | 78,000 | |
| — | 10.00 | — | — | ||
| "Supply, fixing and installation of 32 A 3 phase contactor with 1 NO and 1 NC Make: Schneider/Legrand/L & T/Siemens/Havells/INDOASIAN" | — | — | — | 27,730 | |
| — | 5.00 | — | — | ||
| Supply, fixing and installation of Off-Delay Electronic Timer 5 - 100 sec Input Voltage : 24/200-240 AC, 24 DC Make: Siemens or Similar | — | — | — | 16,240 | |
| — | 300.00 | — | — | ||
| Providing and fixing sheet metal work in CRCA sheet with fabrication of boxes panel boards etc. including cutting, bending, drilling, welding, riveting etc. treated with anti-rust treatment and duly power coated as per the above specification. | — | — | — | 74,400 | |
| — | 30.00 | — | — | ||
| Supplying and erecting of any size electrolyte copper Patti or bar in bus bar chamber / in panel or any other purpose, 500 V with require capacity with 99.9% copper purity with fixing arrangement (like lug or bottle type lug) to both the end with high grade poly olefin insulation sleeve complete. | — | — | — | 33,840 | |
| — | 6.00 | — | — | ||
| Supply, erection, testing, connecting and commissioning of out door type 230/110 Volts DC battery charger suitable to work on 240 Volts 50 HZ single phase AC supply with output current of 35 to 40 Amps as per RDSO Specification No. EL/TL/52 complete with all accessories. | — | — | — | 2,27,772 | |
| — | 6.00 | — | — | ||
| Construction of masonry plinth of suitable size for installation of battery charging with all connected works including required hardware etc. complete. The scope also includes fixing of the battery charger on the masonry plinth with suitable clamps and connected hardware for anti theft arrangement. This work is to be executed as per the planning and instructions of Railway site Engineer with all accessories. | — | — | — | 14,460 | |
| — | 6.00 | — | — | ||
| Supply, Fabrication, and fixing of battery charger mounting arrangements fabricated with MS channels and angles as per DEE/CN/BZA's drg. No. DEE/CN/Drg4A/95 and shall be painted with two coats of red oxide and two coats Aluminum paints with all accessories. | — | — | — | 11,292 | |
| — | 20.00 | — | — | ||
| Supply, erection and marking TPN MCB 63A, 10kA C series in provided distribution board as per specification No. SW-SWR/MCB Make: Legrand/Havells/L&T Or Similar | — | — | — | 30,840 | |
| — | 2.00 | — | — | ||
| Supply, fixing, testing and commissioning of Micro processor Release 125 A ; 4 Pole, MCCB suitable for operation on 415 V,50 Hz 3 Phase AC supply in LT Panel with supply of all connected accessories and allied materials as per specification attached. Make: L&T/Legrand/Havells Or Similar | — | — | — | 28,394 | |
| — | 2.00 | — | — | ||
| Supply, fixing, testing and commissioning of Microprocessor Release 160 A ; 4Pole, MCCB suitable for operation on 415V,50 Hz 3 Phase AC supply in LT Panel with supply of all connected accessories and allied materials as per specification attached.Make: L&T/Legrand/Havells Or Similar | — | — | — | 35,078 | |
| — | 1.00 | — | — | ||
| Supply, fixing, testing and commissioning of Microprocessor Release 200-250 A ; 4 Pole, MCCB suitable for operation on 415V,50 Hz 3 Phase AC supply in LT Panel with supply of all connected accessories and allied materials as per specification attached.Make: L&T/Legrand/Havells Or Similar | — | — | — | 22,546 | |
| — | 1.00 | — | — | ||
| Supply, fixing, testing and commissioning of Microprocessor Release 400 A range; 4 Pole, MCCB suitable for operation on 415V,50 Hz 3 Phase AC supply in LT Panel with supply of all connected accessories and allied materials as per specification attached. Make: L&T/Legrand/Havells Or Similar | — | — | — | 34,945 | |
| — | 1.00 | — | — | ||
| Supply & fixing testing and commissioning of 400 A on-load change over switch suitable to operate on 415 V, 50 Hz conforms to IS:13947-3 with sheet steel enclosure front handle operated. Make:L&T/Legrand/Havells Or Similar. | — | — | — | 29,765 | |
| — | 8.00 | — | — | ||
| Supply, erection, testing and commissioning of all material,excavation, and casting of cement concrete foundation/ concreting in ratio 1:3:6 | — | — | — | 48,568 | |
| — | 40.00 | — | — | ||
| Supplying, erecting & terminating 3 x 120 sq. mm. aluminium 11 kV (UG) HT, XLPE armoured cable on wall/ceiling or laid in provided trench /pipe in an approved manner as per specification No.IS 7098. Part-II(latest) | — | — | — | 38,520 | |
| — | 12.00 | — | — | ||
| Providing and erecting Heat shrinkable outdoor termination kit for 11 kV (E) XLPE HT cable 3 x 120 sq.mm. with necessary material as per specification | — | — | — | 87,648 | |
| — | 1.00 | — | — | ||
| Design, supply,transportation,erection, testing and commissioning of 3 phase 160 KVA,11KV/433V distribution transformer with double Copper winding, three phase, 50c/s, stepdown, off load manually operated tap changerfor HV voltage variation +5% to -5% in steps of2.5%, by off circuit tapchanger, vector group Dyn 11, HV delta, LV star connected ONAN Cooled, filled with fresh transformer oil as per ISS 335,complete with all standard fitting and accessories etc.distribution transformer confirming to IS:1180/2014,Amendment No.4 level-II (Earlier Level-III) or latest. | — | — | — | 7,79,744 | |
| — | 1.00 | — | — | ||
| Supply, testing and commisioning of 100 KVA DG set with AMF panel as per specifications attached | — | — | — | 13,51,376 | |
| — | 180.00 | — | — | ||
| Supply and laying of 4 core 120 sq mm crosslinked polyethylene (XLPE) insulated LT UG cable, PVC outer sheathed, armored with galvanized round steel wire or steel strip and with Aluminium conductor suitable for rated voltage at 1100 volts grade and conforming to IS:7098 (Part- 1)/1988 with amdt. no. 1, 2& 3 (reaffirmed 2005) or latest make:Polycab / KEI / Havells / Finecab / Finolex /Kenter or similar | — | — | — | 1,35,900 | |
| — | 610.00 | — | — | ||
| Supply,erecting, laying, connecting, testing and commissioning of 4 core 70 mm² LT XLPE UG Aluminium Cable, 1100 Volts as per IS:7098/Pt.I/1988 or latest make: Polycab / KEI / Havells / Finecab / Finolex /Kenter/LS/Gloster or similar. | — | — | — | 2,45,220 | |
| — | 610.00 | — | — | ||
| Supply and laying of 4 core 50 sq mm crosslinked polyethylene (XLPE) insulated LT UGcable, PVC outer sheathed, armored with galvanized round steel wire or steel strip and with aluminium conductor suitable for rated voltage at 1100 volts grade and conforming to IS:7098(Part- 1)/1988 with amdt.no. 1, 2 & 3(reaffirmed2005) or latest. make: Polycab / KEI / Havells / Finecab /Finolex /Kenter or similar | — | — | — | 1,87,270 | |
| — | 1180.00 | — | — | ||
| Supply,erecting, laying, connecting, testing and commissioning of 4core 25 mm² LT XLPE UG Aluminium Cable, 1100 Volts as per IS:7098/Pt.I/1988 or latest make:Polycab/KEI/Havells/Finecab/Finolex/Kenter/LS/Gloster | — | — | — | 2,28,920 | |
| — | 960.00 | — | — | ||
| Supply,erecting, laying, connecting, testing and commissioning of 4core 16 mm² LT XLPE UG Aluminium Cable, 1100 Volts as perIS:7098/Pt.I/1988 or latest make:Polycab/KEI/Havells/Finecab/Finolex/Kenter/LS/Gloster | — | — | — | 1,44,960 | |
| — | 3740.00 | — | — | ||
| Supply and running of 8 SWG GI wire is to be laid for earth continuity | — | — | — | 52,360 | |
| — | 200.00 | — | — | ||
| Supply,erecting and laying of HDPE pipe of PE 80 grade in PN-4 outer dia of HDPE pipe 110 mm (nearest 4" dia) and wall thickness minimum 4.1 mm maximum 4.3 mm with "T' joints,bends, elbows etc. including all other connected accessories.Make: M/s.Sudhakar/ Nagarjuna polymer/Nandi/Plasto or similar | — | — | — | 74,200 | |
| — | 800.00 | — | — | ||
| Supply, erecting and laying of HDPE pipe of PE-80 grade in PN-4 outer dia of HDPE pipe 63 mm (nearest 2"" dia) and wall thickness minimum 2.5 mm maximum 2.8 mm with ""T' joints, bends, elbows etc.including all other connected accessories.Make: M/s.Sudhakar/ Nagarjunapolymer/Nandi/Plasto or similar | — | — | — | 99,200 | |
| — | 6.00 | — | — | ||
| Supplying and erecting LT current transformer with bar primary 50/5 to 1000/5 ratio with 15 VA burden erected in provided CRCA box duly secured with insulating materials connected to the meter with test certificates. | — | — | — | 5,268 | |
| — | 1.00 | — | — | ||
| Supplying and erecting panel mounting type digital ammeter having three and half digit LED display,external CT operated,calibrated for 0 to 1000 A AC supply with necessary PVC wire leads and lugs and mounting hard ware on provided panel complete with calibration certificate from manufacturer suitableto operate on 500V. | — | — | — | 1,361 | |
| — | 1.00 | — | — | ||
| Supplying and erecting panel mounting type digital voltmeter having Three and half digit LED display,calibrated for 0-750 V AC suitable to operate on 500 VAC supply with necessary PVC wire leads and lugs and mounting hard ware on provided panel complete with calibration certificate from manufacturer suitable to operate on 500V. | — | — | — | 1,305 | |
| — | 2.00 | — | — | ||
| Supplying and erecting selector switch suitable for voltmeter/ammeter for 3phase AC supply 500/1000 V, 50Hz, on provided box / panel and duly connecting with necessary PVC wire leads and lugs. | — | — | — | 640 | |
| — | 2.00 | — | — | ||
| Supply & provision of 3 Nos RYB indication lamps of LED type including with all connected accessories complete. | — | — | — | 876 | |
| — | 14.00 | — | — | ||
| "Supply and fixing of Power contactor 63 A, 3 Pole AC, coil voltage- 220 V with 1 NO + 1 NC Aux contact cat no.- LC1D633M. Make- C&S electric, L&T, BCH or similar" | — | — | — | 95,466 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
GCC2022works.pdf
ATTACHMENT
GCCCorrectionSlips1to11_compressed.pdf
ATTACHMENT
Earthing Specification
ATTACHMENT
RitesInspectionLetter.pdf
ATTACHMENT
TenderNoNEDE18202627LalwadiPitlineExtension.pdf
ATTACHMENT
TechCircular05-2022provisionofearthelectrodesearthing3_compressed.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .