Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹1.5 CrAccepted-AOC | ₹1.5 Cr | L1 | Accepted-AOC Lowest rate quoted by bidder. |
| 2 | L2₹1.5 Cr+₹3.1 L (2.10%)Rejected-Finance | ₹1.5 Cr+₹3.1 L (2.10%) | L2 | Rejected-Finance Disqualified. |
Tender Value
₹1.5 Cr
EMD Value
₹3.0 L
Closing Date
5 Jan 2026, 3:00 pmClosed
Executive Engineer
Executive Engineer, D.W.and S.Hatia Proj. Division Ranchi.
Barricading work along the inspection road at Hatia Dam, Dhurwa, Ranchi.
2025_DWSD_108218_1
DWSD/F2/03/2025-26
Open Tender
Civil Works
Percentage
90 days
Ranchi
Please refer Tender documents.
2 documents required · 2 mandatory
₹10,000
₹3.0 L
Yes
26 Feb 2026
26 Dec 2025
7 Jan 2026
26 Dec 2025
5 Jan 2026
26 Dec 2025
Making 25cm (10") dia bore upto 4 M depth below ground with hand auger of approved quality in ordinary soil (vide classification of soil item-A) true to pump and without eccentricity in any stage of operation and disposal of the excavated earth upto 50 M lead including all lifts, all complete as per approved design and direction of E/I.
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size)
Chain link fabric fencing mesh of size 50x50 mm made of G.I wire of dia 4mm
Iron and Steel material 65mmx65mmx6mm M.S Angle
Iron and Steel material 50mmx50mmx6mm M.S Angle
Labour for fitting & fixing G.I. woven wire fencing including fixing of post in cement concrete at 2.5 M centres including cost of staples (but excluding the cost of cement concrete angle iron post ,its cutting and making holes,nuts and bolts) all complete as per building specification and direction of E/I.
Drilling 6mm dia holes M.S. angle Iron for fixing of staples etc. as per building specification and direction of E/I.
Supplying, fitting and fixing strainging bolt with nut size 25cmx 10mm dia to tighten the barbed wire comer post complete as per building specification and direction of E/I.
Nuts and Bolts . (using M16 x 24 mm bolts)
Labour for fabricating, erecting, hoisting and fixing in position structural steel work in R.S. joist, channel, Angle, Tee, flat, plate, latice member, built up compound section in column, girder, stair case, or truss including cost of gusset plates, holding down bolts, anchor plates at all heights and depths, bolting, welding(machining wherever necessary) with applying a priming coat of red lead paint all complete as per approved drawing, building specification and direction of E/I.
Providing two coat of painting with ready mixed paint of approved shade and make over steel surface including cleaning the surface throughly , scaffolding and taxes all after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I.
Carriage of materials-
Cement (Lead = 5 km)
Sand (Lead = 20 km)
Chips (Lead =20 km)
Steel Reinforcement (Lead =5 km)
ADD GST 18% Rs.
ADD Labour Cess 1% Rs.
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.21 MB
F2.pdf
Tender Documents • 0.71 MB
BOQ_146131.xls
BOQ • 0.39 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .