SPL REPAIR TO BLDG NO. NP-49 AND PROVN OF BATHROOM AND TOILET BLOCK AT NP-31 AND NP-55 AT 250 TRANSIT CAMP AND PROVN OF 04 X COUNTER, 01 X FPM COUNTER, FALSE CEILING TILING IN FRONT OF VERANDAH FPO AT HQ 71 SUB AREA AND PROVN OF FOUR WHEELER PARKING

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing and rubbish off the premises out side MD land, complete all as specified and directed.

Demolition of brick work or stone boulder masonry, built in cement mortor including all quoins, arches, pillars etc, complete all as specified and directed.

M&L for brick work with sub class ‘B’, old size bricks, straight or curved on plan exc 6 mtr mean radius, built in CM 1:6, complete all as specified and directed.

M&L for brick work with sub class ‘B’, old size bricks, straight or curved on plan exc 6 mtr mean radius, built in CM 1:4, complete all as specified and directed.

M&L for half thick brick work with sub class 'B' brick, old size, built in CM 1:4, complete all as specified and directed.

Demolition of cement concrete (un-reinforced) of any description and in any position, not otherwise specifically provided for, complete all as specified and directed.

Demolition of cement concrete reinforced of any description and in any position, not otherwise specifically provided for, complete all as specified and directed.

Taking down cement plaster of any description on brick work or stone masonry or cement concrete walls including raking out joints, hacking for key, scrubbing down with water including remaval of derbis, complete all as specified and directed.

M&L for 10mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:6, finished the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for 10mm thick rendering on fair faces of ceiling surfaces in CM 1:3, finished the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for 15mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:4 with using water proofing compound, finished the surface even and smooth without using extra cement and including necessary scaffolding (if required), complete all as specified and directed. Note :- (a) WPC shall be measured and paid separately under respective items of BOQ. (b) Rates for scaffolding shall be deemed to include in the quoted rates.

M&L for 15mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:6, finished the surface even and smooth without using extra cement and including necessary scaffolding (if required), complete all as specified and directed. Note :- Rates for scaffolding shall be deemed to include in the quoted rates.

Supply only integral water proofing compound.

M&L for preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of alkali resistance primer, complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over and including a coat of primer over and 2-3mm thick wall care putty, complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceiling and applying two coats of white wash, complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of white wash, complete all as specified and directed.

M&L for non skid ceramic coloured tiles of 7 to 8mm thick (square / rectangular), area of each tile exc 0.18 Sqm but not exc 0.38 Sqm as in floor including skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid/ fixed over and including 15mm thick plaster in CM 1:4, complete all as specified and directed.

M&L for non skid ceramic coloured tiles of 7 to 8mm thick (square / rectangular), area of each tiles exceeding 0. 11 Sqm but not exc 0.18 Sqm, superior premium quality, Grade B-1 as per IS in Water Splashing floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid/fixed over and including 15mm thick screed bed or bedding layer in CM 1:4, complete all as specified and directed.

S&F glazed ceramic coloured tiles of size 600mm x 330/300mm x7mm thick or 350/450mm x 250/300mm x 7mm thick as on verticle surfaces, set and jointed in neat cement slurry, fixed over and including 10mm thick rendering in CM 1:4 and pointed in coloured cement to match the shade of tiles, complete all as specified and diredted. Note :- Size of tiles shall only be decided by Engineer-in-Charge and rates for the same shall be deemed to include in the quoted rates.

Dismantling of stone slabs and tiles, laid, bedded and pointed in any mortar of any description or thickness as in floors, aprons etc, complete all as specified and directed.

M&L for 18-20mm thick machine cut kota stone slab flooring, jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete and rounding of edges, laid over and including 20mm thick screed bed in CM 1:3, complete all as specified and directed.

M&L for 18-20mm thick machine cut kota stone slab as in skirtings, dados, walls, jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, fixed over and including 10mm thick plaster in CM 1:4, complete all as specified and directed.

M&L for marble strip, cut to width not exc 100mm wide, fixed as border in stair case, walkways, strip for floor etc, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, laid/fixed over and including 20mm thick screed bed in CM 1:3, complete all as specified and directed.

M&L for 18-20mm thick granite (of any type) work (table rubbed and polished) as in steps, jambs, pillars, window cills, cooking platforms and the like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and including grinding and polishing with rounding to edges of stone slabs one edge complete, laid/ fixed over and including 20mm thick screed be/ plaster CM 1:4, complete all as specified and directed. Note :- Colure (Red / Black) of granite shall be decided by EIC before incorporating in the work and rates for the same shall be deemed to include in the quoted rates.

M&L for 50mm thick cement concrete 1:3:6 type C-1 (using 20mm graded crushed stone aggregates) as in plinth protection, laid in alternate ways (not exc 2.0 Sqm each) and finished the surface even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection, filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight, complete all as specified and directed.

Taking down chowkats or frames (without taking off shutters from frame), area not exc 1.50 Sqm each including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fasts shall be finished identical to existing finish without any extra cost to Govt.), complete all as specified and directed.

Taking down chowkats or frames (without taking off shutters from frame), area exc 1.50 Sqm but not exc 4.00 Sqm each including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fasts shall be finished identical to existing finish without any extra cost to Govt.), complete all as specified and directed.

M&L for pressed steel frames of size 125x60mm for doors with one or more rebates including necessary lugs, hinges, lock strike plate etc. complete and including one shop coat of red oxide zinc chrome primer, complete all as specified and directed.

S&F 30mm thick flush shutter, solid core construction with block board core and plywood face panels, commercial type on both sides (As per sample, fixed in Bldg No. NP-23 HQ 71 Sub Area), complete all as specified and directed.

S&F factory made 2nd class hard wood rail and style 35mm thick, plain framed, panelled shutters (two panels) with lock rail and panel of 9mm thick BWP commercial ply or 12mm thick veneered partical board with commercial veneering on both sides. The size of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated, complete all as specified and directed.

All as per serial item No. 31.00 here-in-above but glazed and skeleton shutter with sash bar for glass / wire gauge.

S&F galvanised mild steel wire cloth 0.63mm nominal dia of wire and average width of aperture 1.40mm, fixed with tinned tacks or galvanised with wire staples, complete all as specified and directed.

M&L for plain cement concrete 1:3:6 type C-0 (using 12.5mm graded crushed stone aggregates) as filling in back of pressed steel door frame / hold fasts, complete all as specified and directed.

S&F factory made pressed steel frame steel window/vent with glazed & gauged shutter (combined with side hung shutters including box type hinges, steel handle, necessary locking arrangements, peg stay complete with one shop coat of zinc chrome primer including PCC (1:3:6) type B-0 as filling in back side recess profile portion, complete all as specified and directed. Note :- Rates quoted shall be deemed to include for wire gauged and glazed window complete and shall be measurred as one unit.

M&L for mild steel framed work such as grills, gratings etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work including welding, conforming to Fe-290 Gde-E-165, complete all as specified and directed.

S&F 4mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane, complete all as specified and directed.

S&F 150mm long aluminium anodised barrel tower bolts with bright finish, complete all as specified and directed.

S&F 300mm long aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixing clip of sheet, cast or extruded sections and fixing bolts and sliding bolt of extruded sections or cast aluminium alloy, complete all as specified and directed.

S&F 150mm long alunminium handle, cast type, oval shape, complete all as specified and directed.

S&F 150mm long alunminium handle, fabricated type, anodised, complete all as specified and directed.

M&L for preparation of new steel and iron surfaces, exceeding 10cm width or girth and applying two coats of synthetic enamel paint over preprimered surface, complete all as specified and directed.

M&L for preparation of new steel/ iron surfaces of any description, over 10cm in width or girth and applying two coats of synthetic enameled paint over a coat of red oxide zinc chrome primer, complete all as specified and directed.

S&F vitreous china wash down water closet (pedestal pattern) white including connection to drain pipe and to flushing pipe antisyphonage pipe etc. and including plastic water closet seat cover, closet pattern with flat bottom and mild steel chromium plated or aluminum hinges device, complete all as specified and directed.

S&F vitreous china squatting pan ‘Orissa’ pattern of size 580x440mm, white with integral foot rest (excluding flushing system and flush pipe) with ‘P’ or ‘S’ trap, complete all as specified and directed.

S&F 10 Ltr capacity PVC valveless syphonic action type flushing cistern, low level, white with inlet including bracket and 32mm flush pipe of polythylene ball valve, float and handle of low or high density and including 15mm dia PVC connection pipe of 450mm long, complete all as specified and directed.

S&F in replacement viterous china wash basin, pedestral type, white, flat back, size 550mm x 400mm including CP waste couping of 32mm dia, chain and plug and porcelan stopper and Cl brackets of iron size 65x65x6mm including in cement concrete block with PCC 1:2:4 type B-1 and including 450mm long PVC waste pipe of 32mm dia, complete all as specified and directed.

S&F in replacement pillar tap, cast copper alloy, fancy type with capstan head, chromium plated, screwed down, high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed of 15mm bore iron pipe, complete all as specified and directed.

S&F in replacement PVC connection of 15mm dia with PTMT nuts of length 450mm, complete all as specified and directed.

S&F in replacement chromium plated tubular towel rail, 'D' type, 600mm long between flanges, complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connections including cleaning for refixing or removal to store, complete all as specified and directed.

Taking up or down 20mm bore steel tubing and connections including cleaning for refixing or removal to store, complete all as specified and directed.

S&F 15mm bore steel water tubing, medium grade, galvanised with all fittings and fixtures, fixed to wall or ceiling or laid in floors, complete all as specified and directed.

S&F 20mm bore steel water tubing, medium grade, galvanised with all fittings and fixtures, fixed to wall or ceiling or laid in floors, complete all as specified and directed.

S&F 25mm bore steel water tubing, medium grade, galvanised with all fittings and fixtures, fixed to wall or ceiling or laid in floors, complete all as specified and directed.

S&F in replacement of angle valve/ stop cock, cast copper alloy, screwed down high pressure with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe, complete all as specified and directed.

S&F stop valve, chromium plated, cast copper alloy, screwed down high pressure with crutch or butterfly handle, screwed both ends, fixed to 25mm bore iron pipe, complete all as specified and directed.

S&F stop valve, chromium plated, cast copper alloy, screwed down high pressure with crutch or butterfly handle, screwed both ends, fixed to 20mm bore iron pipe, complete all as specified and directed.

S&F stop valve, chromium plated, cast copper alloy, screwed down high pressure with crutch or butterfly handle, screwed both ends, fixed to 15mm bore iron pipe, complete all as specified and directed.

S&F in replacement of 15mm dia bib tap, cast copper alloy, fancy type, chromium plated with crtuch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule, complete all as specified and directed.

Dismantling water tank and remove to store of capacity exc 500 ltrs but not exc 1000 Ltrs with all necessary fittings, complete all as specified and directed.

S&F 1000 ltrs capacity tripple layered rotational moulded polyethylene water storage tank, white colour (cylindrical vertical with closed top) with, hoisted and fixed in position including nipple inlet and outlet and conneting pipes, complete all as specified and directed.

S&F 500 ltrs capacity tripple layered rotational moulded polyethylene water storage tank, white colour (cylindrical vertical with closed top) with, hoisted and fixed in position including nipple inlet and outlet and conneting pipes, complete all as specified and directed.

S&F in replacement ball brass valve, high pressure with polyethene float & fly-nut complete, screwed for 20mm bore iron pipe or brass ferrule, complete all as specified and directed.

S&F in replacement chromium plated towel ring (minimum weight 90 Gram), fixed with brass screws and wooden/plastic cleats, complete all as specified and directed.

S&F factory made 30mm thick PVC door shutter, consisting of panel of Hollow PVC Profile of 24mm thickness, consisting of frame made out of M.S tubes of 19 gauge thickness and size of 19mm x 19mm inserted inside the hollow section of stiles, top and bottom rails and two 19mm x 19mm MS tubes inserted horizontally inside the hollow profile section at an equal distance from top and bottom of door and fixed with hollow profile section using 3mm thick Prelam PVC sheet using screws. Hollow PVC profile shall be lipped with 10mm (5mm x 2) thick x 24mm width on stiles and rails using solvent cement. The inner panel shall be laminated with 5mm thick termite proof, water proof and fire retardant Prelam PVC sheet using solvent cement on both the sides of the panel etc complete as per direction of Engineer-in-Charge.

S&F solid PVC door frame of size 50mm x 47mm, made out of 5mm thick plain colour PVC sheet reinforced with MS. Square tube, in opening as per specification and drawings, complete all as specified and directed.

Dismantling of boarding of any description, fixed in any position with nails, complete all as specified and directed.

S&F false ceiling with everest fiber cement designer tile lvory/ white painted (high pressure steam cured) of 4mm thickness (as per IS-14862) of size 595mm x 595mm and any one of the design (occeanic, lake & hill cascade or electra) in true horizontal level, suspended on interlocking power coated certa black pattern metal grid of hot dipped galvanised steel section (galvanised @12 Grams both side inclusive) consisting of main 'T' runner with suitably spaced joint to get required length and 15x32mm, made of 0.30mm sheet spaced between main 'T' @ 600mm C/C from a ridge of 600x600mm and wall angle of size 15x20mm made of 0.30mm thick sheet and laying false ceiling tile in the grid including required cuttig / making opening for service like diffuser grils light suspended from ciling using GI soffit cleats fixed to existing rafters purlin etc. with dash fastener GI adjustable rod of 3mm dia with galvanised butterfly level clips spaced at 1200mm c/c along main 'T' bottom exposed width of 15mm of all T-sections shall be centre black prepainted with poiyester paint and having a load bearing capicity of 12 Kg/Sqm and re-fixed all existing electric wiring and fixtures, fixed at any height, complete all as specified and directed.

S&F in replacement 25mm dia stainless steel, fancy type curtain rod with bracket/ wall brackets, knobs as per approved design/ colour/ pattern, fixed to wall with SS screws and pvc/wooden gutties, complete all as specified and directed.

Dismantling of asbestos cement (corrugated, semi- corrugated etc.) or CGI or polycarbonate sheets in roof coverings including ridges and in other situation, complete all as specified and directed.

S&F 0.50mm thick prepainted galvalume aluminum zinc coating GI based corrugated steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws, complete all as specified and directed.

S&F 0.50mm thick prepainted galvalume aluminum zinc coating GI based plain steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed self tapping screws, complete all as specified and directed.

S&F 4mm thick solid coloured polycarbonate roof sheets (As per sample kept in GE's office) as in wall affairs or it's equivalent, fixed to wall / roof including angle, flat jointed / 'U' jointed required at conners/top of angling etc. or fixed in curve or circular area with coach screws, washers / 'J' or 'L' hooks, complete all as specified and directed.

S&F aluminium 'H' bar two piece, 50mm wide for jointing sheet including necessary sealant to seal the gaps, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description, not otherwise provided for, complete all as specified and directed.

M&L for rolled mild steel roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, conforming to Fe-410-W (Gde-E- 250) Quality 'A', complete all as specified and diredted.

M&L for hardcore of broken stone or boulders, not exc 63mm gauge, deposited, spread and leveled in layers not exc 15cm thick, watered and rammed to a true surface, complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregates) as in floors / sub base of floors, complete all as specified and directed.

M&L for machine pressed rubber moulded, manufactured / compacted by vibrating table method precast concrete interlocking paver block of any shape and size, confirming to IS:15658-2006 of 60mm thickness, M-35 grade with grey cement and pigment and joints filled with sand, complete all as specified and directed.

M&L for factory made, glossy finished or reflective type (As approved by GE/EIC), coloured chequred cement concrete tiles, size of each tile 30cm x 30cm x 25mm thick, machine pressed, set and jointed in neat cement slurry and jointing with white/ grey cement & pigments to match with tiles, laid/ fixed over and including 20mm thick screed bed in CM 1:4 as in floors, complete all as specified and directed. Note :- Type of chequered tiles shall be approved by GE/EIC before incorporating in the work at all stage.

M&L for sand cushoning bed (filling under floors) or under paver blocks including spreading, leveling, watering if required, complete all as specified and directed.

S&F factory made cement concrete kerb stone in PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregates), outer coloured surface, size 150mm long x 100mm wide x 350mm deep and setting in cement mortar 1:4 with joints to match, complete all as specified and directed.

S&F in replacement shower rose, brass, chromium plated, 125mm dia with or without swivel joint, with and including CP brass arm and wall flange, fixing to steel pipe or union, complete all as specified and directed.

S&F of 6 inch x 6 inch ultra slim shower head with 12 inches arm of chromium plated brass for fixing 15mm dia pipe with bend of 45 degree with flange, complete all as specified and directed.

S&F in replacement CP decorative soap dish of any type, fixed to with chromium plated brass screws, complete all as per specified and directed.

S&F in replacement glass shelf assembly, consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated brackets, guard and railing 60cm long, complete all as specified and directed.

Dismantling of 75/100mm dia cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out from trenches, complete all as specified and directed.

M&L for 100mm bore cast iron spun soil, waste and vent pipes in any length with or without ears with cement joints, laid in trenches/ floors or fixed to walls with MS clamps of suitable size, complete all as specified and directed.

M&L for 75mm bore cast iron spun soil, waste and vent pipes in any length with or without ears with cement joints, laid in trenches/ floors or fixed to walls with MS clamps of suitable size, complete all as specified and directed.

S&F cast iron floor trap of 75mm dia with CP grating including jointing to waste pipe, fixed in cement concrete 1:2:4 type B-1 of size 200mm x 200mm x 250mm, complete all as specified and directed.

S&F in replacement salt glazed stoneware gully traps of size 150x150mm, square or round mouthed, type 'P', complete all as specified and directed.

Surface excavation not exc 30cm deep and avaraging 15cm deep and getting out in any type soil, complete all as specified and directed.

Excavation in trenches not exc 1.5 mtr deep and not exc 1.5 mtr wide for foundation, shaft, well, laying of under groundcable, pipes etc. and getting out in any type of soil, complete all as specified and directed.

Excavation in over area, not exc 1.5 mtr deep for and getting out in any type of soil, complete all as specified and directed.

Returning, filling in including spreading, leveling and well ramming in layers not exc 25cm in thick, complete all as specified and directed.

Removing excavated material to a distance not exc 50 mtr and depositing where directed at a level not exc 1.5 mtr above the starting point, complete all as specified and directed.

Removing excavated material to a distance exc 250 mtr but not exc 500 mtr and depositing where directed, complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregates) as in foundation, filling in and mass concrete, complete all as specified and directed.

M&L for RCC M-25 (Design Mix) as in slabs, shelves, roof projections, drops, chajjas, stair case, complete all as specified and directed.

M&L for RCC M-25 (Design Mix) as in beams, cantilevers, bressummers, lintels over 1.5 mtr span, complete all as specified and directed.

M&L for RCC M-25 (Design Mix) as in columns, pillars, piers, posts, foundation and struts etc, complete all as specified and directed.

M&L for cement concrete 1:2:4, type B-1 (using 20mm graded crushed stone aggregates) as in lintels upto 1.5 mtr clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60cm in height, copings, kneelers, apex stones, bed plates, kerbs stones, water troughs and the like including weathering, slightly rounded and chamfered angles and throating, complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips, complete all as specified and directed.

M&L for mild steel TMT bars, 6-8mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips, complete all as specified and directed.

Use and waste of formwork to rough finished concrete soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200mm thick (Horizontal or sloping), complete all as specified and directed.

Use and waste of formwork to roofs, chhajjas, chullah hoods, trough and similar items including edges with rough finished flat surfaces of concrete, complete all as specified and directed.

Use and waste of formwork to sides and soffits of floor or roof beams haunching, lintels, cantilever shelves including supported overhangs etc. with rough finished flat surfaces of concrete, complete all as specified and directed.

Use and waste of formwork to spiral staircase with sloping or steppped soffits including risers and staingers, finished rough surfaces of concrete, complete all as specified and directed.

Use and waste of formwork to edges of concrete (rough finished) flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work, exc 10cm but not exc 20cm wide, complete all as specified and directed.

S&F factory made steel window (box type) with glazing bars, dovetailed or welded including hinges, steel handles, steel peg stays etc. including one shop coat of red oxide zinc chrome primer, complete all as specified & shown in drawings.

S&F factory made steel window (box type) without glazing bars, dovetailed or welded including hinges, steel handles, steel peg stays etc. including one shop coat of red oxide zinc chrome primer, complete all as specified & shown in drawings.

M&L for water proofing treatment with polymeric standard water proofing membrane, Aquaflex manufactured by M/s Bengal Bitumen / MULTIPLAS STANDARD manufactured by STP TEXAS Ltd / Hyperplas manufactured by IWL Ltd, having 10 years guarantee for water tightness, complete all as specified and with the followings :- (a) Preparation of RCC roof surface and applying one coat of polymeric modified bitumen 85/25 @ 1.2 Kg/Sqm over a coat of polymeric primer @ 0.30 Kg/Sam including cleaning surface, complete all as per manufacturer's specifications and as directed. (b) Providing water proofing treatment with polymeric proofing membrane of 3 Kg/Sqm, consting of 100 micron HMHDPE film centre core including coating he surface with the compatible primer and torch application of membrane with 10cm overlaps as required thereof.

M&L for solar reflective bitumenous aluminium paint @ 0.10 Kg per Sqm over membrance surfaces as in roof, complete all as specified and directed.

S&F factory made PVC internal door frame (Prelam) of size 100mm x 45mm with a wall thickness of 5mm ( +/- 0.25mm), made out of extruded 5mm (+/- 0.25mm) thick PVC sheet manufactured by an ISO:9001-2008 certified company and by joining 3 Nos heat bent PVC sheet sections, the inside section of size 90x30mm shall be made from plain colour PVC sheet of 5mm (+/- 0.25mm) thickness the inside section will be covered by sticking two sections of size 30x35mm and 70x45mm, made from (+/-0.25mm) thick plain PVC sheet. The frame shall be mitre cut at two corners and joined with 4 Nos of 150mm long brackets of 15mm x 15mm MS square tube. The two vertical door frames are to be reinforced with 40mm x 20mm MS tubes of 19 guage through out the farme. The door frame shall be fixed to the wall using 8/100mm long screw through the frame by using anchor fastners. A minimum of 4 Nos screw to be provided for each vertical members and minimum 2 Nos for horizontal member etc, complete as per manufacturer's specifications and direction of Engineer-in-Charge.

S&F 30mm thick factory made internal PVC flush door shutter, wood free, consisting of frame made out of MS tubes of 19 guage thickness and size 20mm x 40mm for stiles as well as top, bottom and lock rail. MS frame shall have a coat of metal primer of approved make and manufacturer. The inside panel shall consist of 20mm thick multi chamber hollow PVC section 1mm wall thickness bonded using solvent cement / cynoacrylate adhesive with 5mm (+/-0.25mm) thick plain/prelam PVC sheet manufactured by an ISO:9001-2008 certified company on both side of the inside panel. All the four edge of the panel to be sealed with lipping of 10mm thick and 20mm wide PVC sheet baton (made by sticking 2 Nos PVC sheet of 5mm (+/- 0.25mm) thickness using PVC solvent cement adhesive. Door edge lipping to be painted with PVC ink of matching colour of plain/ prelam moulded PVC sheet of door 0.20mm thick (5mm x 4mm) thick PVC sheet to be given for lock provision at lock height. Door to be fixed with frame with 3 Nos stainless steel butt hinges of size 100mm and 50mm long steel screws, drilled suitable to pass through both the wall of the MS tube other hardwares should be fixed with 25mm x 8mm size steel screws etc, complete as per manufacturer's specification and directed by Engineer-in-Charge.

S&F 100mm long stainless steel butt hinges, complete all as specified and directed.

Cutting into existing manholes for connecting new drains and making good to pipe and rendering, cutting out to exiting benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1, smooth finished and reforming benching as required for 150mm internal dia of pipe, complete all as specified and directed.

S&F urinal valve auto closing system with built in control cock & wall flange valve of 15mm bore including urinal sperader of CP, complete all as specified and directed.

S&F vitreous china urinal half stall type coloured with grating & union for discharge pipe (excluding flushing cistern) and including waste fitting and urinal spreader of CP, complete all as specified and directed.

M&L for marble works, 16 to 18mm thick Green Marble, machine cut and machine polished and moulding, one side green marble, fixed over jambs of doors/ window cills and urinal partition of wash basin platforms and flooring, skirting, dados and the like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of marble and jointed with grey cement slurry, complete all as specified and directed.

S&F fancy type vitreous china counter top, wash hand basin, "OVAL" shaped, white of size 550x400mm including CP bottle trap of suitable size, inserted in 16-18mm thick mounted green marble stone slab platform by cutting in oval shape etc, completed all as specified and directed. Note :- Green marble cutting shall be measured and paid separately under respective item of this BOQ.

Extra over for cutting and moulding of green marble in oval shape to accommodate WHB as specified in serial item No. 122.00 here-in-above, complete all as specified and directed.

S&F brass chromium plated pillar cock, water fall down type, fancy type, suitable for WHB as specified in serial iem No. 96.00 here-in-above, fixed to 15mm bore pipe, complete all as specified and directed. Note :- Make and model of pillar cock shall be decided and approved by GE/EIC. No extra claim whatsoever shall be admissible on this account.

S&F 110mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints, fixed to walls with MS clamps of suitable size or laid in floor/ trenches or provided in weep holes of retaining wall, complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints, fixed to walls with MS clamps of suitable size or laid in floor/ trenches, complete all as specified and directed.

S&F 75mm bore PVC (SWR) bends (any radius), complete all as specified and directed.

S&F 110mm bore PVC (SWR) bends (any radius), complete all as specified and directed.

S&F PVC (SWR) junction single or double equal or unequal, suitable for 75mm bore pipe, complete all as specified and directed.

S&F PVC (SWR) junction single or double equal or unequal, suitable for 100/110mm bore pipe, complete all as specified and directed.

S&F PVC (SWR) vent cowl, suitable for 75mm bore pipe, complete all as specified and directed.

S&F PVC (SWR) floor trap with CP mgrating including jointing with solvent cement, 75mm dia outlet, complete all as specified and directed.

S&F PVC (SWR) multi floor trap with CP mgrating including jointing with solvent cement, 75mm dia outlet, complete all as specified and directed.

S&F PVC (SWR) gully trap of 125/110mm, setting and jointing with solvent cement, complete all as specified and directed.

S&F 32mm bore low density polyethylene pipes (LDPE) of pressure rating 6 Kg/cm2, fixed complete to walls, ceilings or in floors etc, complete all as specified and directed.

M&L for plain cement concrete 1:3:6 type C-2 (using 40mm graded crushed stone aggregates) as in bed to drain pipes of 150mm bore including packing under and haunching against the sides of pipes after they are laid and tested, complete all as specified and directed.

M&L for 150mm bore reinforced cement concrete pipes, Class NP2, laid and jointed completed with collar, complete all as specified and directed.

M&L for walling of random rubble stone masonry, uncoursed or brought upto course, well bonded, bedded and solidly hearted, built in cement mortar 1:6 including providing weep holes, complete all as specified and directed. Note :- PCC bond stone shall be measured and paid separately under respective item of this BOQ.

S&F precast bond stones of cement concrete 1:3:6 type C-1 (using 20mm graded crushed stone aggregates) of any thickness, size and shape, set in cement mortar 1:6, complete all as specified and directed.

Extra over stone walling for hammer dressing to face stone and dressing of face beds and joints as specified of random rubble walling, uncoursed or brought upto course, hammer dressing with maximum depression on face from straight edge held against the dressed surface not exceeding 20mm for granite or trap stone, complete all as specified and directed.

M&L for hand packing (any thickness) of broken stone boulders at back of wall over arches etc. and raising (or lowering) to the required label, complete all as specified and directed.

M&L for raised pointing to random or polygonal rubble, uncoursed or brought upto courses in cement mortar 1:3, complete all as specified and directed.

Excavating in post holes (or similar holes), each not exc 0.50 Cum and getting out in any type of soil, returning, filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25cm thick, complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregates) as in foundation, filling in post holes, mass concrete etc, complete all as specified and directed.

S&F tinted toughened and tempered glass panels including unframed assemblies (such as frameess doors) comprising of 12mm thick glass pressed by controlled thermal of chemical treatment to increase it's strength compared with normal glass conforming to IS:2553 Part-I, to be fitted as per manufacturer's instructions, complete all as specified and directed by Engineer-in-Charge. Notes :- (a) No cutting and grinding of glass shall be allowed at site of work and the contractor shall procure actual size as required at site in consultation with Engineer-in-Charge prior to placing the order for the same. (b) Rates shall be deemed to include to all fittings such as suitable heavy duty hydraulic floor spring, locking arrangement with cover plates, top and bottom hinges with cover plates, stainless steel 300mm fancy type handle 02 Nos on each shutter and fixtures as stainless steels required at site. (c) The work shall be got executed by the specialist agency as approved of GE. (d) Existing door opening shall be finished identical to existing one, like finishes including holes, cut and any other damage to jambs and lintel. (e) Pattern, design and sticker shall be approved by GE.

S&F mortice lock with two lever MS body (vertical type), 100mm lenth of latch with 3 sets of key, fixed in door shutter with proper in position, complete all as specified and directed.

S&F powder coated aluminium (minimum thickness of powder coating 50 micron) sliding window, shutter of door, window and ventilators including providing and fixing hinges/pivots and making for fixing of fitting wherever required including the cost of roller, locking system, EPDM rubber / neoprene gasket as required with extruded built up standard tubular section / appropriate 'Z' section and other section of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size including necessary filling up the gaps at juction i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium snap beading for glazing/ paneling, CP brass/ stainless steel screws, complete all as specified and directed. Note :- All fitting shall be of ISI marked except cleats. Sizes of each shutter shall be as per site requirement. Aluminium section not less than 1.5mm thick.

S&F powder coated aluminium frame for doors, sliding windows, ventilators with one or more rebates including joining cleats for fixing etc, complete all as specified and directed.

M&L for 18/19mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with SS screws to timber frame work as in cupboard, kitchen cabinet or similar work etc. including 6mm thick teak wood lipping around the board/ shutter, complete all as specified and directed.

S&F 30mm (when opened) continuous (piano) hinges, mild steel, bright finish or electrogalvanised, complete all as specified and directed.

S&F 100mm long alunminium handle, cast type, complete all as specified and directed.

S&F 100mm size hasp and staple, aluminium anodised including bolt to hinge plate and fixed with screws, complete all as specified and directed.

S&F magnet catchers, 50mm steel plate MS body and striking plate including letting in and fixed with SS screws, complete all as specified and directed.

S&F stainless steel zero crank hinges (auto), fancy type (with Euro concealed hinges), fixed to shutters in cupboards of standard size and shape, suitable for modular kitchen, complete all as specified and directed.

S&F telescopic drawer side channels of standard size including roller for moving drawer, mild steel, bright finish or electrogalvanised, suitable for modular kitchen, complete all as specified and directed.

Taking down carefully existing surface / concealed unserviceable aluminum/ copper point wiring (light, fan, socket, power or sunken box) complete including fittings such as switches, ceiling roses, pendants, regulators, sockets, bracket holder, boards light fittings etc. and making good to disturbed surfaces of walls, floors, ceilings etc. where required and finished the existing surfaces after complete of new point wiring, complete all as specified and directed.

Taking down fluorescent tube light fittings, single/double, panel light / LED bulk head fitting, of any wattage or size, for repair or replacement of burnt/worn out accessories or carrying to MES store for reuse or taking in schedule of credit, complete all as specified and directed.

Taking down unserviceable / serviciable MCB DB's / AC's box including MCCB/MCBs of any size/rating and taking in schedule of credit, complete all as specified and directed.

M&L for point wiring using approved color coding as per IS code (Red, Black and Green for single phase circuit) with multi stranded copper condutor 1.5 Sqmm nominal cross section area, single core, PVC insulated and unsheathed FRLSH cable 1100V grade in and including medium grade,PVC concealed conduit ISI marked of dia not less than 20mm and conduit accessories, concealed in wall/ roof/ floor etc. with terminated to new pressed flush metal box and readily available modular cover with outer plates and inner plates etc, suitable for mounting modular type switches, sockets, fan regulators etc. and PVC insulated multistranded copper condutor 1.5 Sqmm nominal cross section area, single core FRLSH cable as earth continuity conductor to common earth and connecting to earth dolly, complete all as specified and directed for the followings :- One light Point, controlled by one, one way switch.

All as per serial item No. 160.00 here-in-above but for one ceiling fan point, controlled by one way switch.

All as per serial item No. 160.00 here-in-above but for one exhaust fan, controlled by one way switch.

All as per serial item No. 160.00 here-in-above but for 3 Pin 5 Amp socket on the same board with other switches.

All as per serial item No. 160.00 here-in-above but 3 Pin 5 Amp Socket on independent board.

All as per serial item No. 160.00 here-in-above but for point wiring with two runs of FRLSH PVC insulated unsheathed, 1100 V grade cable multi stranded copper conductor of size 2.5 Sqmm, drawn through in and including PVC conduit size of not less than 25mm concecled in wall / surface.

All as per serial item No. 160.00 here-in-above but for geyser / AC point with 4 Sqmm on independent board including 4 Sqmm multi stranded copper conductor earth wire connected to common earth/ earth dolly complete.

S&F single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of 16 to 32 Amps, 240 Volts capacity, complete all as specified and directed.

S&F modular switch, single pole, one way, 6 Amps, 240 volts with polycarbonate body, complete all as specified and directed.

S&F modular socket, 6 Amps, 5 pin, flush type, 240 volts with polycarbonate body, complete all as specified and directed.

S&F modular socket outlet, 5 pin, 6 Amps and 15 amps, multipurpose 2 in 1, flush type, 230 volts with polycarbonate body, complete all as specified and directed.

S&F modular switch, single pole, one way, 16 Amps, 240 volts with polycarbonate body, complete all as specified and directed.

S&F modular electronic fan regulator, step type, two module, 120 watt, 230 Volt and making all necessary connections, complete all as specified and directed.

S&F ceiling rose surface bakelite type, size 65x50mm three terminals, complete all as specified and directed.

Re-fixing of any type of LED tube light fittings / panel light / LED bulk head fitting, obtained from serial item No. 158.00 here-in-above, complete with all fixing accessories and connection wire if required, complete all as specified and directed.

S&F 20 Watt LED Light fitting, high quality materials and design, extruded aluminium housing enhances safety with high quality PC diffusers, reliable and robust housing structure, maximize the endurance over the lifetime slim integrated design, easy to install, Efficacy: 110 Im/W and also available in warm white and natural white complete making all connection using 1.5 Sqmm copper conductor multistranded PVC insulated twin core flexible cable from ceiling to light, complete all as specified and directed.

S&F 10 Watt LED light fitting, Trimline Neu is a robust and high performance batten. This LED luminaire comprises of extruded channel in thermally conductive material, high translucent serrated milky white diffusers used to get glare free and smooth light distribution, Efficacy : 110 ImW and also available in warm white and natural white complete making all connection using 1.5 Sqmm copper conductor multistranded PVC insulated 2 Core flexible cable from ceiling rose to fitting, complete all as specified and directed.

S&F in replacement of 35 Watt LED security light fitting with ASTRA NEO, street lights are made up of pressure die cast housing with toughened glass and high power LEDs with secondary optics and IP-66 protection and with 0.60 mtr long 20/25mm dia (As per manufacturer's standard) GI Pipe in 45 degree bend and necessary clamping devices as required at site, complete all as specified and directed.

M&L for submain wiring with two run single core 4.0 Sqmm FRLSH copper conductor cable PVC insulated, unsheathed, 1100 Volts grade including 25mm dia PVC concealed conduit, heavy duty, ISI marked with all accessories such as Tees, elbows, junction boxes etc. as required, fixed on wall alongwith one run of 4.0 Sqmm single core PVC FRLSH insulated unsheathed copper conductor cable as continuous earth wire and connecting to existing main switch board / distribution board, complete all as specified and directed. Note :- Two run of 4.0 Sqmm and one run 4.0 Sqmm cable and one run of PVC conduit shall be measured as one unit/RM.

S&F MCCB DB, TPN, 4 Ways with metal double door CRCA sheet steel power coated, IP-43 protection, suitable for MCB as outgoing, 415 Volts, 3 Phase, complete with appropriate size copper bus bar and neutral link, cutting chases to wall for fixing of DB and making good distrubed wall/surface to match with existing surfaces, complete all as specified and directed.

S&F MCB metalic distributition board 12 Way, double door, 230 Volts, concealed flush to wall for mounting MCBs, factory made, fabricated out of CRCA sheet fitted with DIN channel, neutral link and approriate rated bus bar. DBs shall be semi glossy finished with epoxy polyster based powder paint sprayed and backed at high temperature, between powder paint process to ensure smooth finish and protection against corrsion atmosphere. The DB shall be double door type with hinged door with locking arrangement. The DB shall be of same make as MCBs. DB shall also be provided with lable marking indicating the incoming and outgoing circuits on all ways as specified and shall be of IP-43 protection, complete all as specified and directed.

S&F MCB metalic distributition board 8 Way, double door, 230 Volts, concealed flush to wall for mounting MCBs, factory made, fabricated out of CRCA sheet fitted with DIN channel, neutral link and approriate rated bus bar. DBs shall be semi glossy finished with epoxy polyster based powder paint sprayed and backed at high temperature, between powder paint process to ensure smooth finish and protection against corrsion atmosphere. The DB shall be double door type with hinged door with locking arrangement. The DB shall be of same make as MCBs. DB shall also be provided with lable marking indicating the incoming and outgoing circuits on all ways as specified and shall be of IP-43 protection, complete all as specified and directed.

S&F MCB TPN, 440 Volts, 63 Amps breaking capacity, 10 KA, 'B' Series, complete all as specified and directed.

S&F MCB, SPN, 240 Volts, 32-40 Amps, 50 HZ, 10 KA, 'B' series, complete all as specified and directed.

S&F MCB, SP, 240 Volts, 40 Amps, 50 HZ, 10 KA, 'B' series, complete all as specified and directed.

S&F MCB, SP, 240 Volts, 6-32 Amps, 50 HZ, 10 KA, 'B' series, complete all as specified and directed.

S&F Residual Current Circuit Breakers (RCCB) / Earth Leakage Circuit Breakers (ELCB), AC type, double pole, 40 Amps, 30 mA, complete all as specified and directed.

Taking down the existing geyser of any capacity carefully and deposit to the MES store yard of GE (North) Udhampur and re-fixing the same after completion of B/R works, complete as specified and directed by Engineer-in-Charge.

Taking down ceiling fan / exhaust fan complete and re-fixing the same after completion of B/R works, connecting up to including provision of three core copper conductor cable 1.5 Sqmm nominal cross sectional area and length not less than 0.5 mtr from ceiling rose to fan, complete all as specified and directed. Note :- Fans shall be deposited to MES store yard after taking down.

S&F exhaust fan, steel body, AC, single phase, 230 Volts, size 300mm sweep with blades, frame and louvers, complete all as specified and directed.

Supplying, laying/fixing and testing XLPE insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cable (heavy duty), 1100 Volts grade with stranded aluminium conductor of size 25 Sqmm 4 Core, laid in trenches/ floor/ pole/ thorugh GI pipe complete including cutting/ chasing to any surface and making good to the disturbed surface to match the existing and including taking out/down existing cable of any type, complete all as specified and directed.

Supplying, laying/fixing and testing XLPE insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cable (heavy duty), 1100 Volts grade with stranded aluminium conductor of size 10 Sqmm 2 Core, laid in trenches/ floor/ pole/ thorugh GI pipe complete including cutting/ chasing to any surface and making good to the disturbed surface to match the existing, complete all as specified and directed.

Supplying, laying/fixing and testing XLPE insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cable (heavy duty), 1100 Volts grade with stranded aluminium conductor of size 6 Sqmm 2 Core, laid in trenches/ floor/ pole/ thorugh GI pipe complete including cutting/ chasing to any surface and making good to the disturbed surface to match the existing and including taking out/down existing cable of any type, complete all as specified and directed.

S&F LED garden light fitting, 9/10 Watt, post top lantern bollard 0.80 mtr bamboo, IP-65 generation energy saving environment friendly long life aesthetically designed, pressure die cast, powder coated housing with PC diffuser. Efficient high output LED with IP-65 protection suitable for garden ways and heritage sites including necessary electric connection and fixing arrangement on PCC block of size 45cm X 45cm alogwith fixing nuts, bolts and PVC insulated aluminium conductor, stranded type of size 4 Sqmm 2 Core including taking down old/unserviceable garden light fitting of any type and wattage, complete all as specified and directed. Note :- Cost of PCC block shall be deemed to include in the quoted rates.

S&F LED Gate Light in aluminum die cast with modern artistic design and white PC diffuser, suitable for retrofit LED lamps including of 1N x A60 7.5 Wwall LED Filament Lamp complete with internally prewired and connecting up with twin core flexible copper conductor cable of suitable size complete including taking down old/unserviceable gate light fitting, complete all as specified and directed.

M&L for earthing complete with galvanized steel earth plate electrode of size 600x600x6mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to earth lead wire of GI wire 4mm dia by means of nuts, bolts, washers and check nuts of galvanized iron and including 15mm bore GI pipe light grade upto 1.5 mtr below GL as protection pipe and excavation, earth work, charcoal dust, common salt, PCC 1:3:6 type C-1 chamber with cover and RCC 1:2:4 type B-1 (using 20mm graded crushed) stone aggregate, reinforced with 6mm dia round bars @ 75mm c/c both way with MS handle 12mm dia, PGI funnel and wire mesh, complete all as shown in electrical plate No. 3 of SSR Part-I and connected to earthing test point including testing on completion, complete all as specified and directed.

M&L for dry sand cushioning to underground cables with a layer of sand 8cm thick before laying the cable and 15cm thick after laying cable and stretching the cable, complete all as specified and directed.

Supply and laying old size brick, Class ‘B’ covering as mechanical protection to underground cable with well burnt, complete all as specified and directed.

M&L for 40mm bore GI tubing, light grade with all fitting and laid in floor or fixed to wall/ pole with and including MS clamps of suitable size, complete all as specified and directed.

S&F electric water heater, storage type, steel body with copper inner tank and heating element upto 2 KW, capacity 25 litters, BEE 5 Star rated, complete with all accessories such as safety valve, thermostate, NRV, connection piece etc, complete all as specified and directed.

M&L for cutting the existing MS/DI/CI/GI branch pipe line of any size carefully by means of gas cutter, removing the rusted MS pipe lines, making provision for joining new MS/CI/DI/GI pipes of same size by welding MS flanges of suitable size and making leake proof joint including all jointing materials like bolts, nuts and gaskets required at site complete all as specified and directed by the Engineer-in-Charge. Note :- GI pipes shall measured and paid separately under respective item of this BOQ.

M&L for point wiring with 1.5 Sqmm PVC insulated unsheathed FRLS multistranded copper conductor, medium grade, ISI marked, drawn into and including PVC concealed conduit with all accessories from terminal box to junction of ceiling and wall and rest of circuit conductor wire drawn into and including surface PVC rigid non metalic conduit for one ceiling fan / light point, controlled by one switch with and also including 1.5 Sqmm continious earth wire connected to common earth dolly complete including concealed conduit of dia not less tham 25mm and half portion surface wiring through ceiling/stress complete with all accessories including MS sheet metal 1.2mm thick switch board of suitable size, fixed/flush to wall with 3mm thick ebonite sheet cover and necessary screws, cap washers etc. complete all as specified and directed.

All as per serial item No. 201.00 here-in-above but for one ceiling fan point, controlled by one way switch.

All as per serial item No. 201.00 here-in-above but for 3 Pin 5 Amp socket on the same board with other switches.

All as per serial item No. 201.00 here-in-above but 3 Pin 5 Amp Socket on independent board.

All as per serial item No. 201.00 here-in-above but wire size 2.5 Sqmm to controlled the 3 Pin 5/15 Amps socket outlet on independent board and providing earth continuity wire using PVC insulated, FRLSH 1100 volts grade unsheathed single core multistranded copper conductor cable of size 2.5 Sqmm.

S&F switch piano, flush type, one way, single pole, 5 Amps, suitable for 240 Volts, 50 Hz, AC supply, complete all as specified and directed.

S&F switch socket combination, 5 Amps, suitable for 240 Volt, 50 Hz, AC supply, complete all as specified and directed.

S&F switch socket combination, 2-in-1, 5/15 Amps, suitable for 240 Volt, 50 Hz, AC supply, complete all as specified and directed.

S&F electronic fan regulator, stepped type, 240 Volt, flush type, suitable for 1200/1400mm sweep ceiling fan, complete all as specified and directed.

S&F surface/ recessed mounting LED luminaire 600mm x 600mm in size, 35/36 Watt, 220 Volts AC, recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders and LED lamp, suitable for roof ceiling including connecting up with driver with three core flexible copper conductor of suitable size, complete all as specified and directed.

M/S GURU DEV BUILDERS (BID ID -3424608)

HANS RAJ SHARMA (BID ID -3424627)