PROVISION OF RETAINING WALL NEAR BLDG NO. T-36 AND TOILET BLOCKS NEAR VTC BLDG AND CERTAIN REVENUE WORKS AT KALIMPONG UNDER GE 867 EWS

Amount

Surface excavation not exceeding 30cmdeep and averaging 15 cm deep and getting out in soft/loose soil complete all as specified and directed.

Excavating in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth; for foundation, laying of pipe, cable etc., or for shafts, wells, cesspits, manholes, pier holes, etc., not exceeding 10 sqm on plan and getting out in soft/loose soil all as specified and directed by Engineer-in-charge.

M&L for Plain cement concrete 1:4:8 mix type D2 (using 40 mm graded stone aggregate) in foundations, filling and mass-concrete etc., all as specified and directed by Engineer-in-Charge.

M&L for factory made precast cement block masonry with solid blocks made of Plain cement concrete 1:3:6 mix type C1 (using 20 mm graded stone aggregate) exceeding 10cm width and setting in cement mortar 1:6 complete all as specified and directed by Engineer-in-charge. Make : Shankar Saw Mills/Sangam Prefeb Products or equivalent make as approved by GE.

M&L for moorum/red bajri filling in floors or pavings, laid in layers not exceeding 15cm thick, spread, levelled and rammed including watering complete all as specified and directed by Engineer-in-Charge.

M&L for Hardcore with Broken stone/boulders of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface all as specified and directed by Engineer-in-charge.

M&L for factory made precast cement block masonry with solid blocks made of Plain cement concrete 1:3:6 mix type C1 (using 20 mm graded stone aggregate) 10cm width and setting in cement mortar 1:4 complete all as specified and directed by Engineer-in-charge. Make : Shankar Saw Mills/Sangam Prefeb Products or equivalent make as approved by GE.

M&L for 100 mm thick Plain Cement Concrete 1:4:8, type D2 (using 40mm graded stone aggregate) as in sub base and finishing even and rough to receive toping layer complete all as specified and directed by Engineer-in-charge.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick square/rectangular area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc., jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles laid on and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed by Engr-in-charge.

M&L for coloured glazed ceramic tiles of size 300x200x7mm thick on vertical surfaces such as skirting/dado, jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles laid on and including 10mm thick rendering in cement mortar 1:4 backing coat complete all as specified and directed by Engr-in-charge. Make for Item No 9&10: NITCO/ SOMANY/ ASIAN / JOHNSON/KAJARIA/ORIENT BELL

M&L for reinforced cement concrete 1:2:4 mix, type B1 (using 20 mm graded stone aggregate) as in beams, cantilevers, bressummers, lintels exceeding 1.5 m span, bands etc., all as specified and directed by Engineer-in-Charge. Note: Formwork and reinforcement shall be measured and paid seperately.

M&L for reinforced cement concrete 1:2:4 mix, type B1 (using 20 mm graded stone aggregate) as in chajjas and the like all as specified and directed by Engineer-in-Charge. Note: Formwork and reinforcement shall be measured and paid seperately.

Use and removal of steel formwork to sides and soffits of floor or roof beams, bands, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc., for rough finished surfaces of concrete flat all as specified and directed by Engineer-in-Charge.

Use and removal of steel formwork to soffits of chajjas and similar item including edges, for rough finished surfaces of concrete flat all as specified and directed by Engineer-in-Charge.

M&L for Mild steel deformed TMT bars 10mm dia and above as in reinforcement to concrete cut to length bent to shape required including cranking bending and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as directed by Engr-in-charge.

M&L for Mild steel deformed TMT bars 8mm dia as in reinforcement to concrete cut to length bent to shape required including cranking bending and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as directed by Engr-in-charge.

M&Lfor Mild steel deformed TMT bars 5mm dia and over up to and including 10 mm dia as in stirrups, spacers and binders , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with and including mild steel wire (annealed) not less than 0.9mm dia all as specified.

M&L for 40 mm thick Plain Cement Concrete Type B0 1:2:4 (using 12.5 mm graded stone aggregate) as in damp proof cource to horizontal or vertical surfaces including necessary formwork, with and including integral waterprofing compound @ 3% by weight of cement complete all as specified and directed by Engineer-in-Charge.

M&L for plain cement concrete 1:2:4 mix, type B1 (using 20 mm graded stone aggregate) as in lintels upto 1.5 mm clear span, cills,steps; seismic and other similar bands, plinth courses, string courses, lacing courses parapets and railings upto 60 cm in height, copings kneelers, apex stones, bed plates, water trough and like including weathering, slightly rounded or chamfered angles and throating including necessary form work complete all as specified and directed by Engineer-in-Charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in soft/loose soil complete all as specified and directed by Engineer-in-charge.

Removing surplus excavated soil to a distance not exceeing 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed by Engineer-in-charge.

S&F factory made PVC Solid Door frame of size 50mmx47mm made out of 5mm plain coloured PVC sheet reinforced with MS Square tube, fixed in opening as per specification and dawings.

S&F Factory made Solid panel PVC Door Shutter of 30mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colourr PVC 'C' channel having a PVC sheet strip 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail ; Panelling of plain clour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beeding and jointed together with solvent cement as per specification and drawing. Make for Item No. 22&23: - SINTEX / RAJSHRI PLASTIWOOD/ NANDI/ UNIVERSAL

S&F 100 mm size mild steel cold rolled medium weight butt hinges complete all as specified and directed.

S&F 250mm long aluminium alloy anodised sliding door bolts with hasp & staple (bolt type) and fixing clip of sheet , cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy all as specified and directed.

S&F 150 mm long Aluminium alloy handles cast type anodised all as specified and directed.

S&F 200 mm long Aluminium anodised barrel tower bolts of extruded aluminium section all as specified and directed. Make for Item No. 24 to 27: - CROWN/ CLASSIC/ JYOTHI/ AMIT/ MOWJEE/ARGENT/Bharat/Alans/Hettich/Everlite or any ISI marked make as approved by GE.

S&F steel ventilators with top hung shutters (glazed or wire mesh shutters) fitted with box type hinges with suitable MS handles, peg stays complete all as directed by Engr-in-charge. Make: M/s Madhu industries / M/s.SEN Harvick / M/s. Shiv Mular / M/s. AGEW. / M/s. Multiwyn Industries Corpn/ M/s Ganesh rolling shutters/M/s Venkateswara rolling shutters or equvalent make as approved by GE.

S & F 3mm thick figured glass pin head type fixed with oil putty and necessary clips/nut bolts area not exceeding 0.5Sqm in each pane complete all as directed by Engr-in-Charge. Make:- TRIVENI/ SAINT GOBAIN/ MODIGUARD/ATUL/ HINDUSTAN or equivalent as approved by GE.

M&L for rendering 15 mm thick on brickwork or concrete surfaces in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and directed by Engr-in-charge.

M&L for rendering 15 mm thick on brickwork or concrete surfaces in cement mortar 1:4 finished fair and even including waterproofing compound @ 3% by weight of cement as per manufacturer's instructions complete all as specified and directed by Engr-in-charge.

M&L for preparing newly plastered surfaces of walls and applying three coats of white wash complete all as specified and directed by Engineer-in-charge. Make: LOVELYCEM/ SURYACEM/ JANATHACEM / LUCKYCEM or equivalent make as approved by GE.

M&L for preparing newly plastered surfaces of walls and applying two coats of premium Exterior emulsion paint over one coat of primer complete all as specified and directed by Engineer-in-Charge. Make: APEX of ASIAN or equivalent in JENSON & NICHOLSON/ BERGER/ SHALIMAR

M&L for preparation of new or previously un treated surfaces of steel and iron surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed. Make: ASIAN/ SHALIMAR/ BERGER/ JENSON&NICHOLSON/IEL/NEROLAC/IEL

S&F Fe 410-W (Gde-E- 250) quality-A Rolled steel sections, as in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., complete all as specified and directed by Engineer-in-charge.

S&F Fe 410-W (Gde-E- 250) quality-A rolled mild steel plates (plain or chequered), as in base plates etc., square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment complete all as specified and directed by Engineer-in-charge.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet (trepezium or tile pattern etc.) 0.50 mm thick (with 0.45 mm BMT) of any colour having tensile strength of 550 Mpa (pitch of corrugation shall be 200mm to 250mm and crest shall be 28mm to 32mm) as in roof covering/ cladding to wall fixed with self tapping screws complete all as specified and as directed by Engineer-in-charge. Make: TATA BLUESLOPPE/ LLYODS /JMBS/EVEREST INDUSTRIES LTD/CRIL or equivalent as approved by GE.

M&L 75 mm thick PCC 1:3:6, type C1 (using 20mm graded stone aggregate) in plinth protection/path laid in alternative bays finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

S&F soap dish, vitreous China White, approximate size 160 x 160 x 90mm fixed with plugs with chromium plated brass screws all as specified and directed by Engineer-in-Charge.

S&F Orrissa pattern vitreous china squatting pan white colour of size 580x440mm with integral footrest (Excluding flushing cistern and flush pipes) but including cement concrete bedding and P or S trap as required including PVC pipe upto finished floor level to connect flush pipe, complete all as directed by Engineer-in-Charge. Make: HINDWARE / NEYCER/ PARRYWARE / CERA

S&F bib taps 15 mm bore, cast copper alloy chromium plated screwed down high pressure, with crown or capstan head, screwed for iron pipe all as specified and directed by Engr-in-Charge. Make: SEIKO/RYBO/SPECTRUM/ NMC/L&K

S&F Grating doom 100 mm dia of PTMT (Minimum weight 25 grams) all as specified and directed by Engineer-in-Charge. Make: PRAYAG/POLYTUFF or equivalent as approved by GE.

S&F Vitreous China wash basin, white, angle back, of size 580x440 mm, excluding taps, waste chain and plug and porcelain stopper but including brackets and 40mm dia brass chromium plated waste fitting and 40mm dia 90cm long PVC waste pipe, all as specified and directed by Engr-in-Charge. Make: HINDWARE / NEYCER/ PARRYWARE / CERA

S&F Pillar taps fancy type 15 mm bore, cast copper alloy, chromium plated with crown or capstan head screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks & fly-nuts, screwed for iron pipe, all as specified and directed by Engr-in-Charge. Make: SEIKO/RYBO/SPECTRUM/ NMC/L&K

S&F PVC valveless, symphonic action type, flushing cistern 10ltr capacity, low level, white with inlet ball valve float and handle along with suitable flush pipe/bend including brackets complete all as directed by Engr-in-Charge. Make: PARRY WARE (SLIMLINE)/ COMMANDER/ HINDWARE

S&F vitreous china bowl urinal flat back, size of 465 x 355 x 265 mm (minimum), white with grating and union for discharge pipe incl providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement complete all as directed by Engr-in-charge. Make: HINDWARE / NEYCER/ PARRYWARE / CERA

S&F Stop/angle valves 15 mm bore, cast copper alloy chromium plated screwed down high pressure, with crown or capstan head, screwed both ends for iron pipe or for unions all as specified and directed by Engr-in-Charge. Make: SEIKO/RYBO/SPECTRUM/ NMC/L&K

S&F 15mm bore GI water tubing medium grade with all fittings and fixed to wall, floor, ceiling complete all as specified and as directed by Engr-in-charge. Make: TATA/JINDAL/ZENITH

S&F towel rail 600mm long of PTMT fixed with and including chromium plated brass scres and wooden/plastic cleats (Minimum weight 190gms) complete all as directed by Engr-in-Charge. Make: PRAYAG/POLYTUFF or equivalent as approved by GE.

S&F PVC connection pipe 15mm dia, 300mm long with PTMT check nuts and washer on both ends complete all as directed by Engr-in-Charge. Make:- PRAYAG/POLYTUFF or equivalent as approved by GE.

M&L PVC (SWR) gully trap 125/110mm plain with grating including jointing with solvent cement complete all as specified and directed by Engr-in-Charge.

S&F PVC (SWR) pipes 110mm bore single socket in any length with rubber ring joints fixed to wall or laid in floors complete all as directed by Engr-in-Charge.

S&F PVC (SWR) pipes 110mm bore single socket in any length with rubber ring joints laid in trenches or under floors complete all as directed by Engr-in-Charge.

S&F PVC (SWR) pipes 75mm bore single socket in any length with rubber ring joints fixed to wall or laid in floors complete all as directed by Engr-in-Charge.

S&F PVC (SWR) bends (any radius) suitable for 75mm bore pipe fitted with access door complete all as directed by Engr-in-charge.

S&F PVC (SWR) bends (any radius) suitable for 110mm bore pipe fitted with access door complete all as directed by Engr-in-charge.

S&F PVC (SWR) vent cowl suitable for 110mm bore pipe complete all as directed by Engr-in-charge. Make for item No 52 to 58: PRINCE/ SUDHAKAR/ NANDI/ FINOLEX/ SWASTIK/SUPRIME

M&L for plain cement concrete bed 1:3:6, type C2 (using 40 mm graded stone aggregate) to drain pipe 100/110 mm bore including packing under and hunching against the sides of pipes after they laid and tested complete all as directed by Engineer-in-Charge.

M&L for PCC 1:3:6 type C2 (using 40 mm graded stone aggregate) as in surface channels, drains including fair finishing inner surface of drain or channel using extra cement, including forms, moulds, mitred/ stopped ends etc., complete all as specified and directed.

M&L for excavation over areas not exceeding 1.5 m deep and getting out in soft/loose soil complete all as specified and directed.

M&L for excavation over areas exceeding 1.5 m deep and not exceeding 3 m deepand getting out in soft/loose soil complete all as specified and directed.

M&L for Plain cement concrete 1:3:6 mix type C2 (using 40 mm graded stone aggregate) in foundations, filling and mass-concrete etc., all as specified and directed by Engineer-in-Charge.

M&L for reinforced cement concrete 1:2:4 mix, type B1 (using 20 mm graded stone aggregate) as in walls, retaining walls, basement walls, ballast walls and the like, any thickness complete all as specified and directed by Engineer-in-Charge. Note: Formwork and reinforcement shall be measured and paid seperately.

M&L for reinforced cement concrete 1:2:4 mix, type B1 (using 20 mm graded stone aggregate) as in slabs supported on walls, colums, beams, etc., complete all as specified and directed by Engineer-in-Charge. Note: Formwork and reinforcement shall be measured and paid seperately.

Use and removal of steel formwork to soffits of slabs etc., for rough finished surfaces of concrete flat all as specified and directed by Engineer-in-Charge.

Use and removal of steel formwork to edges of concrete slabs etc., exceeding 20 cm wide for rough finished surfaces of concrete flat all as specified and directed by Engineer-in-Charge.

Use and removal of steel formwork to faces of walls, retaining walls, basement walls, ballast walls and the like vertical or batter for rough finished surfaces of concrete flat all as specified and directed by Engineer-in-Charge.

M&L for rendering 15 mm thick on brickwork or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement including waterproofing compound @ 3% by weight of cement as per manufacturer's instructions complete all as specified and directed by Engr-in-charge.

M & L Precast RCC 1:2:4 type B1 (using 20 mm graded stone aggreagate) as in cover slabs set in cement mortar 1:4 including all necessary form work and finishing exposed surfaces of concrete fair and even complete all as specified and directed by Engr-in-charge.

M&L for brick work with sub class 'B' old size bricks, in one brick thick honey-comb walling built in cement mortar l:4 complete all as specified and directed by Engineer-in-Charge.

M&L for loose filling with broken brickbats of gauge 80 to 150 mm in soakage pits, soakage wells etc., complete all as specified and directed by Engineer-in-Charge.

M&L for plain cement concrete 1:3:6 mix, type C2 (using 20 mm graded stone aggregate) as in retaining walls, any thickness, size or shape including pilasters, buttresses etc., complete all as specified and directed by Engineer-in-Charge. Note: Formwork shall be measured and paid seperately.

M&L for plain cement concrete 1:3:6 mix, type C1 (using 20 mm graded stone aggregate) as in coping, kneelers, apex stones, bed plates, water trough and like including weathering, slightly rounded or chamfered angles and throating including necessary form work complete all as specified and directed by Engineer-in-Charge.

M&L for boulder pitching, hand packed tightly and grouted with cement and sand mortar 1:6 complete all as specified and directed by Engr-in-charge.

S&F for 75mm dia PVC(SWR) pipe(4.50 KGF) for weep holes complete all as specified and directed by Engineer-in-Charge. Make: PRINCE/ SUDHAKAR/ NANDI/ FINOLEX/ SWASTIK

M&L for broken stone or boulders of gauge n exc. 150 mm as in hand packing (any thickness) at back of retaining wall/ walls over arches etc. and raising (or lowering) to the required level complete all as specified and directed.

M&L for 75 mm thick Plain Cement Concrete 1:4:8, type D2 (using 40mm graded stone aggregate) as in sub base and finishing even and rough to receive toping layer complete all as specified and directed by Engineer-in-charge.

M & L for 100 mm thick plain cement concrete 1:2:4 type B2 (using 40 mm graded stone aggregate) as in floor and the like laid in alternative bays in panels, and finishing cement concrete surface even and smooth without using extra complete all as specified and directed by Engr-in-charge.

Forming 65 mm deep x 10 mm wide construction (Dummy) joint filled with sealing compound grade A complete all as specified and directed by Engineer-in-Charge.

S&F 20 mm dia bore medium grade galvanised iron tubing with all fittings and fixtures fixed to wall, roof, floor or laid in trenches complete all as specified and as directed by Engineer-in-Charge.

All as per item No. 81 above but 25 mm dia bore. Make for Item No. 81&82: TATA/ ZENITH / JINDAL

Supply and fixing Rotational moulded polyethylene water storage tank cylindrical vertical double layered, 500 ltrs capacity with closed top hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed by Engineer-in-Charge. Make: SINTEX/ INFRA/ GP/ ROTEX/ ORIPLAST/ ASHISH/ POLYCON or equivalent ISI marked make as approved by GE.

S&F Symet ball valve 25 mm with high pressure of PTMT with epoxy coated aluminum rod & high density plastic ball screwed for iron pipe and fixed min weight for 25 mm 455 gms complete all as specified and directed by Engineer-in-Charge. Make:- PRAYAG/POLYTUFF or equivalent as approved by GE.

S&F gun-metal, globe or gate valves of with iron wheel head, screwed both ends for iron pipe of 20 mm dia bore and fixed including taking down existing unserviceable valve complete all as specified and directed by the Engineer-in-Charge.

All as per item No. 85 above but 25 mm dia bore. Make for Item No. 85&86: LEADER/NETA/ANCHOR/NMC/ DURGA/ZOLOTO or equivalent ISI marked make as approved by GE.

M & L Fe 290 Gde -E-165 mild steel of angle or tee with web and flanges cut to shape, drilled and counter-sunk for screw, including bending and weilding angles as necessary ,as in staging for water tanks including painting with two coats of black bitiminious paint over a coat of red oxide zinc chrome primer complete all as specified and as directed by Engineer-in-Charge.

M&L for point wiring complete with 1.5 Sqmm PVC insulated unsheathed single core multi standard copper conductor 1100 V grade drawn through in and including PVC conduit concealed walls/ceiling and terminated in sunken box of modular type suitable for fixing switches, sockets etc.,including inner and outer cover plate, including 1.5 Sqmm PVC insulated Copper conductor cable as earth continuity conductor and connecting to common earth dolly for One light/fan point controlled by one 5 Amps one way switch/One 3 pin 5 Amps socket outlet point on independent board including testing on completion complete all as directed by Engr-in-charge.

M&L for point wiring complete with 2.5 Sqmm PVC insulated unsheathed single core multi standard copper conductor 1100 V grade drawn through in and including PVC conduit concealed walls/ceiling and terminated in sunken box of modular type suitable for fixing switches, sockets etc.,including inner and outer cover plate, including 2.5 Sqmm PVC insulated Copper conductor cable as earth continuity conductor and connecting to common earth dolly for One 3 pin 15 Amps socket outlet point on independent board including testing on completion complete all as directed by Engr-in-charge. Make for Item No. 88&89 Cable: (i) Finolex, (ii) Plaza, (iii) Havells, (iv) Polycab, (v) KEI, (vi) Anchor Conduit: (i) Kinjal, (ii) Alwyn (iii) Harsh, (iv) Finolex (v) Berlia (vi) Plaza

Supply and fixing modular switch one way 6 Amps, 1 module complete all as directed by Engr-in-charge.

Supply and fixing modular switch one way 16 Amps, 1 module complete all as directed by Engr-in-charge.

Supply & fixing modular socket, 6A-2/3 pin combined 2 module complete all as directed by Engr-in-charge.

Supply and fixing modular socket 6/16A, 6 pin, 2 module complete all as directed by Engr-in-charge. Make for Item No 90 to 93: - MK/ANCHOR ROMA/CRABTREE/ NORTH WEST/LEGRAND/HAVELLS

S&F decorative wall mounting, SS finish fixture with opal glass diffuser suitable for 40 W incandescent candle lamp including lamp complete all as specified and as directed by Engineer-in-Charge. Make: Cat part No. LHJE02106499 of Havells or quivalent model of Crompton /Philips /Surya

Supply and fixing surface mounting LED round shape down lighter 10 watts, slim, sleek profile, low glare to prevent eye strain, surge protection of 2 KV with wide voltage 160-360V, BIS certified, CCT 6500K, light neutral white colour temp-5700K complete all as specified and as directed by Engineer-in-Charge. MAKE: Philips Model-Astra Prime Cat No. (HSN Code) - 9451090 or equivalent model of Surya/Crompton/Havells.

S&F Sleek LED mirror light fitting 2ft fitting surface/pendent mounting provided with high output diffuser complete all as specified and as directed by Engineer-in-Charge. Make: Cat Part No. LCL-07-CDL of Crompton or equivalent in Philips /Bajaj/Surya//Havells

S&F sheet metal enclosure DB SPN 4 way 240 V with 200 Amp rated bus bar, powder coated, double door complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing MCB SPN 40 Amps, 10 KA breaking capacity, 240 volts, 50 Hz complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing MCB SP 5 to 32 Amps, 10 KA breaking capacity, 240 volts, 50 Hz complete all as specified and as directed by Engineer-in-Charge. Make for Item No. 97 to 99: HPL/INDOASIAN/ HAVELLS/C&S/ STANDARD

S&F ceiling rose 3 terminal PVC/Polycarnonate, isolated body complete all as specified and as directed by Engineer-in-Charge. Make: (i) Anchor (ii) Plaza, (iii) Havells (Crabtree) (iv) ABB (v) Shalabh

S&F Exhaust Fan heavy duty PVC body AC Single Phase 230/240 Volts of size 200mm Sweep complete all as directed. MAKE: Riviera bolt 8" Cat No. 1335 of Crompton Greaves or equivalent in Havells/Bajaj

M&L for sub main wiring complete with 2 runs of 6 Sqmm PVC insulated heavy duty and unsheathed cable with multistranded copper conductor and drawing through and including rigid PVC conduit of 25 dia concealed in wall/ceiling and connecting terminal ends including provision of 1 run of 6 Sqmm insulated multistranded copper cable as earth continuity conductor and connecting to earth dolly complete all as directed by Engr-in-charge. Note: 2 runs of 6 Sqmm and one run of 6 Sqmm and one run of conduit pipe shall be measured as one unit length. Make Cable: (i) Finolex, (ii) Plaza, (iii) Havells, (iv) Polycab, (v) KEI, (vi) Anchor Conduit: (i) Kinjal, (ii) Alwyn (iii) Harsh, (iv) Finolex (v) Berlia (vi) Plaza

MS BRAHMA CONSTRUCTION

HEM RAJ GURUNG

SANJAY SAW MILL

M/S G. K. SUTHAR

S K ENTERPRISES

MS MAYA PRAKASH GOEL AND SONS

SANJAY MITTAL