ADDITION ALTERATION IMPROVEMENT TO CERTAIN OMQs AND SMQs AT VSN NAGPUR

Amount

B/R PORTION

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Demolition of cement concrete (un-reinforced) floors and pavings exc 15 cm thickness above ground floors such as in roofs, floors (other than ground floors), staircases, landings, chajjas, beams and similar suspended work including floor finishes complete all as specified and as directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exc 15 cm thickness below or above ground level complete all as specified and as directed.

Material and Labour for 25mm thick Cement concrete 1:2:4, type B-0 (12.5 mm graded stone aggregate) complete all as specified and as directed.

Material and Labour for Screed bed or bedding layer of mortar 15mm thick for laying floor finishes in CM 1:6 complete all as specified and as directed.

Material and labour for Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tile not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match shade of tile complete all as specified and as directed.

Material and Labour for vitrified ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm, in vertical surfaces such as skitings, dado set and jointed in neat cement slurry and pointed in white or coloured cement to match shade of tile complete all as specified and as directed.

Material and Labour for joint free Non-skid Coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06sqm but not exceeding 0.11 sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match shade of tile complete all as specified and as directed.

Material and Labour for glazed ceramic coloured tiles in vertical surface 300x450x7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match shade of tile complete all as specified and as directed.

Material and Labour for rendering 10 mm thick as in backing coat on fair face of brick walls/ concrete surfaces for tiles in CM 1:4 complete all as specified and as directed.

Taking down cement plaster on brick or stone wall/ceiling/chajjas etc including raking out joints hacking for key ,scrubbing down with water etc complete all as specified and as directed.

Material and Labour for rendering 15 mm thick in CM 1:6 over brick or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

Material and Labour for rendering 15 mm thick in CM 1:4 over brick or concrete surfaces finished even and smooth without using extra cement mixed with water proofing compound @ 3% by weight of cement complete all as specified and as directed. Note : WPC will be measured and paid separately

Material and Labour for rendering 10 mm thick in 1:3 over brick or concrete surfaces or on chajjas finished even and smooth without using extra cement complete all as specified and as directed.

Supply only approved integral water proofing compound.

Material and Labour for preparing newly plastered surfaces and applying two coats of acrylic distemper over one coat of primer over two coats of wall care putty complete all as specified and as directed.

Material and Labour for preparing newly plastered ceiling surfaces and applying three coats of white wash complete all as specified and as directed.

Material & Labour for preparation of newly plastered wall surfaces and applying two coats of exterior emulsion paint of electric blue or AF blue colour or equivalent colour as approved by GE, including cornices, pilasters etc complete all as specified and directed. Make of Paint : Dulux ICI or Apex Ultima of Asian Paints or equivalent in Berger Paints

Material and Labour for preparing of old decorated plastered surfaces of ceiling and applying two coats of white wash complete all as specified and as directed.

Material and Labour for complete removal of existing treatment of surfaces, including filling the cracks with crack filler if any on surfaces of ceiling and applying two coats of white wash complete all as specified and as directed.

Material and labour for complete removal of existing treatment from old decorated wall surfaces including filling the cracks with crack filler and applying two coats of acrylic distemper over a coat of primer, over a coat of wall care putty, complete all as specified and as directed.

Material and Labour for preparing old surfaces wall and applying two coats of white wash complete all as specified and directed

Supply and fixing Grating doom 100mm dia of (Minimum weight 25gms) complete all as specified and as directed.

Supply and fixing 100mm dia bore CI Bend diminishing pieces or tapers (larger bore measured) complete all as specified and as directed.

Supply and fixing 75mm dia bore CI Bend diminishing pieces or tapers (larger bore measured) complete all as specified and as directed.

Supply and fixing 100mm bore Cast iron soil ,waste and vent pipes in any length with or without ears with cement joints, laid in trenches or in floors complete all as specified and as directed.

All as per item No. 26 above but fixed on wall complete all as specified and as directed.

Supply and fixing 75 mm bore Cast iron soil, waste and vent pipes in any length with or without ears with cement joints, laid in trenches or in floors complete all as specified and as directed.

All as per item No. 28 above but fixed on wall complete all as specified and as directed.

Supply and fixing 100mm bore Slotted vent cowl complete all as specified and as directed.

Supply and fixing 100mm dia Cast iron floor trap,with grating including jointing waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and as directed.

All as per item No 31 above but 75mm dia Nahani trap complete all as specified and as directed.

Supply and fixed in repairs 32mm dia, polyethylene pipe (LDPE) of low density of pressure rating 6kgf/cm2 fixed completely to wall/floor for wash hand basin complete all as specified and as directed.

Supply and fixed in repairs PVC connection 15mm size with PTMT nuts of length 450 mm complete all as specified and as directed.

Taking down chowkat with shutters without taking off shutters from the frame, area exceeding 1.5sqm but not exceeding 2 sqm each complete all as specified and as directed.

Taking down chowkat with shutters without taking off shutters from the frame, area not exceeding 1.5sqm each complete all as specified and as directed.

Taking down shutters of any description, area not exceeding 1 sqm each complete all as specified and as directed.

Re fixing same opening of shutters of any description, area exceeding 1 sqm each and not exceeding 2 sqm each complete all as specified and as directed.

Material and Labour for 18/19mm thick Block boards,grade 2 quality interior grade commercial type fixed with screws to timber frame work complete all as specified and as directed.

Supply and fixing IInd class hard wood plain solid, straight ,chowkats and frame, framed rebated on the solid, rounded or chamfered put together with glue pinned at joints complete all as specified and as directed.

Supply and fixing pressed steel frames for doors with one or more rebates of size 125mm x 60mm including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and as directed.

Supply and fixing 30mm thick flush door shutter solid core construction with block board core and plywood face panels commercial type on both sides complete all as specified and as directed.

Supply and fixing FRP moulded door shutter of approved brand, 35mm thick, gel coat finish on both sides, having raised panel design. Total construction of door, glass reinforcement combination, resin used other parameters shall be confirming to IS 14856 : 2000. Shutter to have "C"in "C" contraction with extra reinforcement on side & edges. Cavity of panels to be filled with 32-35 Kg/cum density rigid polyurethane foam and wooden member to be provided for taking up hinges & fixtures. the total shutter to be water proof & resistant mild acids & alkalis, complete all as specified and as directed.

Supply and fixing 30mm thick Flush shutters for loft, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

Supply and fixing second class hardwood glazed and skeleton shutters 35mm thick open rebated and prepared to receive glass gauge etc with sash bar divided into squares edges of framing plain chamfered or rounded fitted with cut and mitered beads for securing glass or gauze etc sizes of members of shutters as specified in SSR part-I section 8 clause 8.20 (a) fitted to chowkats complete all as specified and as directed.

Dismantling of Wall and ceiling boards (fibre,pulp,insulation etc) or insulation boards /slabs /blankets ,any thickness including cover fillets complete all as specified and as directed.

Material and Labour for 25mm thick prelaminated particle board interior grade prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with screws to timber frame work complete all as specified and as directed.

Material and Labour for 1.5 mm thick Decorative laminate type 1 of surface finish ,colour and pattern as approved complete all as specified and as directed.

Material and Labour for 6mm thick Cover fillets of standard hard board 40mm wide and fixing with screws complete all as specified and as directed.

Supply and fixing 300 mm long, mild steel ordinary rat rail springs including roller and roller plate complete all as specified and as directed.

Supply and fixing butt hinge, medium weight ,cold rolled mild steel 100mm long complete all as specified and as directed.

Supply and fixing butt hinges, medium weight ,cold rolled mild steel 75mm long complete all as specified and as directed.

Aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolt and sliding bolts of extruded sections or cast aluminium alloy 300 mm long and fixed complete all as specified and as directed.

Supply and fixing floor door stopper of aluminium alloy body double and tongue anodised with rubber shoe and fixed of size 150 mm complete all as specified and as directed.

Supply and fixing aluminium anodised barrel tower bolt of extruded section 200 mm long and fixed complete all as specified and as directed.

Supply and fixing aluminium anodised barrel tower bolt of extruded section 100 mm long and fixed complete all as specified and as directed.

Supply and fixing extruded aluminium alloy handle fabricated type anodised 150 mm long complete all as specified and as directed.

Supply and fixing extruded aluminium alloy handle fabricated type anodised 100 mm long complete all as specified and as directed.

Supply and fixing hasp and staple, safety type aluminium anodised with hinge pin including bolt to hinge plate and fixed with screw 125 mm long complete all as specified and as directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

Supply and fix framed work such as grills, gratings,gates etc, with ends of bars shouldered and or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders framed balusters walk ways, railings, frame work of water tanks and similar work conforming to Fe.290, Gde-E-165 complete all as specified and as directed.

Supply and fixing solid PVC Door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with M.S square tube, complete all as specified and as directed.

Supply and fixing factory made solid panel PVC doors shutter 30mm thick (Style) consisting of frame made out of M.S tubes for top &bottom rails M.S frame shall be coved with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail lock rail & bottom rail on either side & as gap insert for top rail & bottom rail panelling of plain colour PVC sheet to be fitted in the M.S frame welded /sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, complete all as specified and as directed.

Supply and fixing aluminium framed windows any pattern, fixed/side hung/sliding (two or three track) using powder coated standard alluminium sections, of approved make with or with out sash bars suitable for 4mm thick glazing including necessary jointing cleats, complete all as specified and as directed. Note : Glazing shall be measured and paid separately

Supply and fixing aluminium louvered type ventilator weighing 0.55kg/M with 4mm thick frosted glass and all fittings, closing and opening type complete all as specified and as directed.

Supply and fixing steel windows with side hung shutters including projecting type hinges, with steel handles, steel peg stay complete with glazing bars, dovetailed or welded including taking down old one complete all as specified and as directed.

Supply and fixing steel ventilators with top hung shutters including hinges, with steel peg stay complete including taking down old one complete all as specified and as directed.

Supply and fixing 4mm thick figured glass pin head type and glazing with, in squares exc 0.5 sqm in each pane complete all as specified and as directed.

Supply and fixing 4mm thick sheet plain glass ordinary quality and glazing with, in squares exc 0.5 sqm in each pane complete all as specified and as directed.

Supply and fixing 4mm thick sheet tinted glass ordinary quality and glazing with in squares exc 0.5 sqm in each pane complete all as specified and as directed.

Supply and fixing stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and as directed.

Supply and fixing of high strength fancy type ornamental curtain rod of outer dia 19mm & inner dia of 16mm including matching colour galvanised steel brackets of thickness 1.6mm complete all as specified and as directed.

Material and Labour for preparing of new surfaces of steel and iron work of any description not specifically mentioned otherwise over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

Material and Labour for preparing of old painted surface of steel and iron work of any description not specifically mentioned otherwise over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

Material and Labour for preparing new surfaces of wood of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

Material and Labour for preparing of old painted surface of wood work of any description not specifically mentioned otherwise over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

Dismantling of stone slabs and tiles of any description or thickness in floors ,aprons etc and laid bedded and pointed in any mortar complete all as specified and as directed.

Material and Labour for 20mm thick granite (of any type ) work (table rubbed and polished ) in steps, jambs, pillars, window cills, cooking platforms and like in cement (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

Demolition or brick work or stone/boulder masonry built in cement mortar or cement lime mortar including all quoins,arches,pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed.

Material and Labour for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:4 complete all as specified and as directed.

Material and Labour for Brick work with fly ash bricks, straight or curved on plan to any radius in half brick thick walls, built in CM 1:4 complete all as specified and as directed.

Material and Labour for preparing newly plastered surfaces and applying three coats of white wash complete all as specified and as directed.

Material and labour for machine cut kota stone flooring 20-25 mm thick over cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and making 2 Nos of 3mm thick grooves on edge of treads of staircase etc complete all as specified and as directed.

Material and labour for machine cut kota stone slab 20-25 mm thick in riser of steps,skirting,dado and pillar laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab, complete all as specified and as directed.

Material and labour for machine cut cudappah stone 20-25 mm thick over cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

Material and Labour for Rounding to edges of stone slabs one edge ,such as in steps cooking platform and other similar situations complete all as specified and as directed.

Material and Labour for providing PCC 1:3:6 type C2 (using 40mm graded stone aggregate) 75mm thick finishing cement concrete surfaces even and fair without using extra cement as in plinth protection , path etc including necessary form work and provision of joints filled with bitumen complete all as specified and as directed.

Supply and fixing in repairs sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs washers and wastes including cement mortar bedding to dwarf wall or including supply & fixing CI cantilever brackets and connecting union to pipe overall size 915mm X460mm and bowl size 410mm X330mm X160mm complete all as specified and as directed. Make : Johnson or equivalent in jaquar/parry ware /prayag

Supply and fixing 75mm bore pipe traps "P" or "S" complete all as specified and as directed.

Supply and fixing 100mm bore pipe traps "P" or "S" complete all as specified and as directed.

Supply and fixing 100mm cast iron sanitary connection "P" branch with branch 375 to 450 mm long excluding joint complete all as specified and as directed.

Material and Labour for PVC (SWR) gully trap 125/110 mm setting and jointing with solvent cement complete all as specified and as directed.

Supply and fixing 75mm PVC (SWR) bend any radius complete all as specified and as directed.

Supply and fixing 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed.

Supply and fixing 75mm PVC (SWR) pipes single socket in any length with rubber ring joints in trenches or in floors complete all as specified and as directed.

Supply and fixing 15mm dia Bib taps cast copper alloy with crutch or butterfly handles screwed down screwed for iron pipe fixed in repair complete all as specified and as directed. Make : Jaquar, Model : FLR 5047N Quarter turn or equivalent model in Zoloto/Leader

Supply and fixing paper holder fixed to walls with chromium plated (CP) brass screws complete all as specified and as directed. Make : Jaquar, Model : AHS-1553 or equivalent model in Zoloto/Leader

Supply and fixing wash basins vitreous china (flat back or angle back type and any size ,including cutting for and pinning in ends of brackets or erecting stand but inclusive of supply and fixing of suitable size and length waste pipe complete all as specified and as directed. Make : Jaquar, Model : JDS-WHT-25501 or equivalent model in Parryware/Cera

Supply and fixing Chromium plated shower rose with or without swivel joints and any size including fixing to steel pipe or union complete all as specified and as directed. Make : Jaquar, Model : OHS 1789 or equivalent model in Zoloto/Leader

Supply and fixing Glass shelf 22" with brass chromium plated railing complete all as specified and as directed. Make : Jaquar, Model : AKB-35771 or equivalent model in Zoloto/Leader

Supply and fixing glazed shelf with brass chromium plated railing complete all as specified and as directed. Make : Jaquar, Model : CAN-1173 or equivalent model in Zoloto/Leader

Supply and fixing towel rail of stainless steel 600mm long between flanges including screws and wooden /plastic cleats complete all as specified and as directed. Make : Jaquar, Model : AHS 1581H or equivalent model in Zoloto/Leader

Supply and fixing CP soap dish including fixed to plugs with chromium plated brass screws complete all as specified and as directed. Make : Jaquar, Model : AQN-7731 or equivalent model in Zoloto/Leader

Supply and fixing brass chromium plate concealed stop cock full turn regular body with adjustable wall flange size 15mm complete all as specified and as directed. Make : Jaquar, Model : CON-083 KN or equivalent model in Zoloto/Leader

Supply and fixing brass chromium plated, 3 in 1 wall mixture model regular half turn complete all as specified and as directed. Make : Jaquar, Model : CON-281KN or equivalent model in Zoloto/Leader

Supply and fixing in repair PVC mirror cabinet of size 350x450mm complete all as specified and as directed. Make : Prayag, Code : 551 or equicalent model in Commander

Supply and fixing brass chromium plated tumbler holder complete all as specified and as directed. Make : Jaquar, Model : AKP-35741P or equivalent model in Zoloto/Leader

Supply and fixing low level flushing cistern 10 litres capacity (exclusive of brackets) and connections to pipes and fixing of chain and pull or lever if any complete all as specified and as directed. Make : Jaquar, Model : CHS-WHT-205 or equivalent model in Parryware/Cera

Supply and fixing brass chromium plated pillar cock 15mm size quarter turn type, central hole basin mixer with popup waste system with 450mm long braided hoses complete all as specified and as directed. Make : Jaquar, Model : FUS-29052 B or equivalent model in Zoloto/Leader

Supply and fixing water closet (EWC), vitreous china, white (excluding fixing bolt, flushing cistern and flush pipe) with 'S' or 'P' trap Size 790 x350 x630 mm (squatt pattern) complete including provision of lime concrete bedding all as specified and as directed. Make : Jaquar, Model : CNS-WHT-753SB or equivalent model in Parryware/Cera

Supply and fixing plastic water closet seat ,cover black ,closet pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified and as directed. Make : Jaquar, Model : CNS-WHT-111N or equivalent model in Parryware/Cera

Supply and fixed in repair 15mm dia 2 way Bib cock cast copper alloy with crutch or butterfly handles screwed down screwed for iron pipe complete all as specified and as directed. Make : Jaquar, Model : OPL-15041 or equivalent model in Zoloto/Leader

Supply and fixing brass chromium plated hand shower (Health faucet) with 1meter long easy flex tube in chrome finish and wall hook with NRV (back flow preventer) complete all as specified and as directed. Make : Jaquar, Model : ALD-577 or equivalent model in Zoloto/Leader

Supply and fixing towel rack 600mm long with lower hangers of CP with and including chromium plated brass screws and wooden /plastic cleats complete all as specified and as directed. Make : Jaquar, Model : AQN-7781 or equivalent model in Zoloto/Leader

Supply and fixing in repair stainless steel wall mounted rack of size 630 x700 x220 mm and thickness of sheet not less than 0.05 mm with provision of keeping plates and other crockery fixed with screws and rawl plug etc on wall complete all as specified and as directed.

Supply and fixing SS 202 steel grade 5mm wire Thali basket (Size 17"x20"x8") complete all as specified and as directed.

Supply and fixing SS 202 steel grade 5mm wire Cup- saucer basket (Size 17"x20"x4") complete all as specified and as directed.

Supply and fixing SS 202 steel grade Plain utility (Size 17"x20"x4") complete all as specified and as directed.

Supply and fixing SS 202 steel grade 5mm wire plain utility (Size 17"x20"x8") complete all as specified and as directed.

Supply and fixing SS 202 steel grade 5mm wire cutlery basket (Size17"x20"x4") complete all as specified and as directed.

Supply and fixing SS 202 steel grade 5mm thick wire Dustbin holder(Size 9"x12" ) complete all as specified and as directed.

Supply and fixing Telescopic channels 500mm regular complete all as specified and as directed.

Supply and fixing Nickel and chromium plated auto close hinges regular complete all as specified and as directed.

Supply and fixing shutter 18 mm thick waterproof marine ply with both lamination one side white and other side specified colour with edge binding complete all as specified and as directed.

Supply and fixing 600mm carecase made with MDF board and doors with Marine ply with both side lamination one side white and other side specified colour with edge binding complete all as specified and as directed.

Supply and fixing aluminium 'G' section handles complete all as specified and as directed.

Supply and fixing 20 Gde steel hollow section welded frame with powder coated (white colour) of various section for base frame complete all as specified and as directed.

Supply and fixing asbestos Cement sheet 12mm thick for loose (panel) complete all as specified and as directed.

Supply and fixing ply 18mm thick lamination (white colour ) both side Innotek drawer (Heavy drawer capacity 35 Kg) complete all as specified and as directed.

Supply and fixing in repair vitreous china squatting pan of orissa pattern, long pan, size 580mmX440mm white with 'P' or 'S' trap, front or back inlet and integral foot rests, any pattern including making good to floor complete all as specified and as directed.

Supply and fixed in repairs 15mm dia Chromium plated fancy type Bib taps cast copper alloy with crutch or butterfly handles screwed down screwed for iron pipe complete all as specified and as directed.

Taking down carefully existing bitumen tar felt including plaster, concrete/brick coba /tiling from the roof till RCC slab and roughening the surface and removing the rubbish to a distance exceeding 500m but n.exc 1Km & depositing where directed.

Taking down carefully existing bitumen tar felt including plaster (excluding brick coba) till RCC slab and roughening the surface and removing the rubbish to a distance exceeding 500m but n.exc 1Km & depositing where directed .

Material and labour for roof treatment on RCC non accessible roof slab including parapet if any etc. complete as mentioned below and all as specified and as directed:- (i) Cleaning the concrete surfaces of RCC roof slab after demolition/taking down of existing water proofing treatment thoroughly with wire brushes, washed and dried. (ii) Checking the roof slab by flooding test with water till total elimination of leakage/seepage/ dampness all as specified in SSR Part-I (after ascertaining location of leakage/seepage/ dampness, pressure grouting shall be operated at the required locations). (iii) Brushing surface with neat cement slurry at the rate of 3.00kg of cement per Sqm. (iv) Cleaning the plastered roof surfaces and applying a coat of hot blown bitumen primer 85/25 @ 0.3 kg/sqm on top of dry surface. (v) Aluminium Foil APP membrane of 3mm thick with non woven polyester core laid and bonded to the sub-strata and over-laps shall be sealed/fused by flame "torch', application method and all as per manufacturer's instructions.

Material and labour for roof treatment on RCC accessible roof slab complete as mentioned below and all as specified and as directed:- (i) Cleaning the concrete surfaces of RCC roof slab after demolition/taking down of existing water proofing treatment thoroughly with wire brushes, washed and dried. (ii) Checking the roof slab by flooding test with water till total elimination of leakage/seepage/ dampness all as specified in SSR Part-I (after ascertaining location of leakage/seepage/ dampness, pressure grouting shall be operated at the required locations). (iii) Brushing surface with neat cement slurry at the rate of 3.00kg of cement per Sqm. (iv) Cleaning the plastered roof surfaces and applying a coat of hot blown bitumen primer 85/25 @ 0.3 kg/sqm on top of dry surface. (v) APP modified polymeric membrane of 3mm thick with non woven polyester core laid and bonded to the sub-strata and over-laps shall be sealed/fused by flame "torch', application method and all as per manufacturer's instructions. (vi) A coat of hot blown bitumen @ 1.20 Kg/Sqm shall be applied over polymeric membrane and blinded with clean dry sand at the @ of 0.5 kg/Sqm.

Material and Labour for Screed bed or bedding layer of mortar 20 mm thick in CM 1:4 with WPC for laying floor finishes complete all as specified and as directed.

Material and Labour for Cement concrete tiles 25cm x 25cm x 22mm thick, machine pressed; set jointed and pointed with chemical compound as per manufactures instruction complete all as specified and as directed.

Material and Labour for PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in filleting and benching slightly rounded etc including necessary form work complete all as specified and as directed.

Material and Labour for PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate to fill undulations to achieve uniform slope of RCC roof slabs complete all as specified and as directed.

Material and Labour for rendering over roof slab 10 mm thick in CM 1:3 on concrete surfaces mixed with water proofing compound @ 3% by weight of cement and finished surfaces fair and even complete all as specified and as directed. Note : WPC shall be measured and paid separately

Material and Labour for cutting groove exc 200mm but n exc 250 mm girth in brick or stone walls and making good the surfaces using PCC 1:2:4 type B0 or screed in CM 1:3 after inserting water proof bituminous membrane complete all as specified and as directed.

Dismantling existing PVC water tanks exc 500 litres & n. exc 1000 litres complete all as specified and as directed.

Disconnecting existing PVC water tanks, of capacity exc 500 liters & n.exc 1000 litres setting aside (or lowering) for repair work and hoisting if required, reconnecting, refixing after repairs complete all as specified and as directed.

Supply and fixing 1000 Litres triple layered Rotational moulded polyethylene water storage tank (Cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and as directed.

Taking up/down steel tubing 15 mm bore and connections complete all as specified and as directed.

Taking up/down steel tubing 20 mm bore and connections complete all as specified and as directed.

Taking up/down steel tubing 25 mm bore and connections complete all as specified and as directed.

Supply and fixing GI water tubing of bore 15 mm dia medium grade with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and as directed.

Supply and fixing GI water tubing of bore 20 mm dia medium grade with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and as directed.

Supply and fixing GI water tubing of bore 25 mm dia medium grade with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and as directed.

Supply and fixing 20 mm dia Stop valves,cast copper alloy,screwed down,high pressure,with crutch or butterfly handle,screwed both ends for unions and fixed complete all as specified and as directed.

Supply and fixing 25 mm dia Stop valves,cast copper alloy,screwed down,high pressure,with crutch or butterfly handle,screwed both ends for unions and fixed complete all as specified and as directed.

Supply and fixing PVC SWR 75 mm bore pipe single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed.

Supply and fixing PVC SWR 110 mm bore pipe single socketed in any length with rubber ring joints fixed to walls including taking down old one complete all as specified and as directed.

Supply and fixing for 20 mm bore ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule complete all as specified and as directed.

Supply and fixing for 25 mm bore ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule complete all as specified and as directed.

Material and Labour for reinforcement exposed RCC surfaces by removing the loose material, cleaning the reinforcement with rust remover & applying bonding agent and finishing with 20 mm thick screed in CM (1:3) with mixing adhesive complete all as specified and as directed. Note : Reinforcement bars required to be welded to exposed reinforcement if necessary shall be measured & paid separately.

Material and Labour for 6 to 8 mm dia reinforcement mesh including welding to the existing exposed reinforcement complete all as specified and as directed.

Supply and fixing 10 litre capacity PVC low level flushing cistern (ISI marked), white syphonic action type valve less with inlet ball valve, float and handle complete including 32mm dia PVC flush pipe and 15mm bore PVC connection 30cm long with brass nuts and washer both side and connected complete all as specified and as directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition), in chajjas, beams and similar suspended work including floor finishes complete all as specified and as directed.

Grubbing up plants from concrete roof/brick wall surfaces and applying antiweed chemical on surface and making good by filling holes and leveling with PCC 1:2:4, type B0 including necessary scaffolding if required (upto G+1 building) etc., complete all as specified and as directed.

Excavating in trenches, not exc 1.5m wide and not exc 1.5m in depth; for foundation etc. or for shafts, wells, cesspits, manholes, pier holes etc. not exc 10 sq. m on plan and getting out in hard/dense soil, complete all as specified and as directed.

Material and Labour for PCC 1:4:8 Type D2 using 40mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and as directed.

Use and removal of formwork to sides of concrete foundations, footings, bases of columns, raft and beams, sides and soffits (if any) of foundation and plinth beams , and similar work, vertical or to batter, work in rough finished flat surfaces of concrete complete all as specified and as directed.

Material and Labour for RCC, M-25 design mix using 20mm graded stone aggregate as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under reamed piles and mass concrete complete all as specified and as directed.

Use and removal of formwork to sides of pillars, posts, struts, piers, columns and stanchions, square, rectangular or polygonal surfaces of concrete work in rough finished complete all as specified and as directed.

Material and Labour for RCC, M-25 design mix using 20mm graded stone aggregate as in columns, pillars, piers, posts and struts etc complete all as specified and as directed.

Use and removal of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports overhangs etc, also splays between floors and beams, etc., work in rough finished flat surfaces of concrete complete all as specified and as directed.

Material and Labour for RCC, M-25 design mix using 20mm graded stone aggregate as in beams complete all as specified and as directed.

Use and removal of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), work in rough finished flat surfaces of concrete complete all as specified and as directed.

Material and Labour for RCC, M-25 design mix using 20mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

Material and Labour for mild steel TMT bars of 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Material and Labour for mild steel TMT bars 5mm dia and over upto including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Material and Labour for complete removal of existing treatment from wall surfaces including cornices, pilasters etc and applying two coats of exterior emulsion paint of electric blue or AF blue colour or equivalent colour as approved by GE over a coat of exterior wall care putty (Make : Birla) complete all as specified and as directed. Make of Paint : Dulux ICI or Apex Ultima of Asian Paints or equivalent in Berger Paints

Supply and fixing precast ornamental type POP cornices of width not exceeding 250mm on both side at the junction of wall and ceiling wall all necessary fixtures complete all as specified and as directed.

Supply and fixing in repair to 9 feet pulley operated cloth drying system aluminium anodised 20mm dia pipes, channels assembly, locking system to hide rope knot, rope 4 mm dia HDPE double core and fitting materials etc. complete all as specified and as directed.

Material and Labour for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete all as specified and as directed.

Supply and fixing mild steel flat iron hold fast including bolts conforming to Fe 410-0of E-250 complete all as specified and as directed.

Material and Labour for plain cement concrete 1:3:6 type C1 using 20mm graded stone aggregate for fixing hold fast and making good to disturbed surfaces complete all as specified and as directed.

Supply and fixing joint free Non - skid Ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match shade of tile complete all as specified and as directed.

Material and Labour for 2nd class hard wood exc 3 but n. Exc 6 Sqcm plain fillets, bullnosed, splayed, chamfered or rounded on one edge or face,, clean sawn, secured with nails or brads complete all as specified and as directed.

Supply and fixed in repairs 15mm dia fancy type chromium plated concealed angular stop valves screwed down high pressure with crutch or butterfly handle screwed both end for iron pipe or union and fixed complete all as specified and as directed.

Material and Labour for plain cement concrete 1:5:10, type E2 using 40 mm graded stone aggregate as in sunken floor complete all as specified and as directed.

Dismantling existing PVC water tanks exc 250 litres & n. exc 500 litres complete all as specified and as directed.

Supply and fixing 500 Litres capacity, triple layered Rotational moulded polyethylene water storage tank (Cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and as directed.

Supply and fixing waste coupling of PTMT suitable for 32mm bore discharge pipe (half or full threaded with minimum weight of 45gms) complete all as specified and as directed.

Supply and fixing PVC waste pipe 32mm dia fixed to waste coupling complete all as specified and as directed.

Supply and fixing pillar taps 15mm bore dia of pipe cast copper alloy with capstan heads; chromium plated screwed down high pressure with or without lettered HOT or cold with long screwed shanks and fly-nuts screwed for iron pipe and fixed complete all as specified and as directed.

Material and Labour for anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed.

Material and Labour for at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and as directed.

Refixing 15mm dia old steel tubing and connections in new or old position (Walls, ceiling, floors, etc) complete all as specified and as directed.

Refixing 20mm dia old steel tubing and connections in new or old position (Walls, ceiling, floors, etc) complete all as specified and as directed.

Material and labour for grouting in roof through PVC nipples at a spacing of 45 to 60cm C/C including drilling injection points to a depth of 75-100mm, providing 10mm dia PVC nipples and pressure grouting using with and including cement mixed with plasticizing admixture @ 225gms/50kg of cement to fill up all capillaries/ voids/ honeycombing areas inside concrete with pressure of 2 to 4 Kg/Sqcm and continued till refusal. After grouting, nozzles to be sealed with the sealing compound/mortar etc, all as per manufacturers instructions complete all as specified and as directed. Make : FOSROC (model CEBEX100) or PIDILITE (model 207 PIDICRET 8AM)

Disconnecting existing PVC water tanks, of capacity exc 250 liters & n.exc 500 litres setting aside (or lowering) for repair work and hoisting if required, reconnecting, refixing after repairs complete all as specified and as directed.

E/M PORTION

Taking down DB/main switch of any size and making good disturbed surface to match the existing complete all as specified and as directed.

Taking down carefully sub-main wiring of any description and making good disturbed surfaces to match the existing complete all as specified and as directed.

Material and Labour for sub main wiring (concealed) complete with four single core 6 Sqmm FRLS PVC insulated unsheathed stranded copper conductor cable drawn through in and including 25 mm dia rigid non-metallic PVC conduit heavy grade and conduit accessories including 6 Sqmm FRLS PVC insulated unsheathed stranded copper earth cable connected to common earth dolly complete and including cutting chasing in walls for concealed wiring using machine cutting and making good the disturbed surface complete all as specified and as directed. Note: 5 runs of 6 sqmm cable including earth wire & one run of PVC conduit shall be measured as single unit

Material and Labour for sub main wiring (concealed) complete with two single core 6 Sqmm FRLS PVC insulated unsheathed stranded copper conductor cable drawn through in and including 20 mm dia rigid non-metallic PVC conduit heavy grade and conduit accessories including 6 Sqmm FRLS PVC insulated unsheathed stranded copper earth cable connected to common earth dolly complete and including cutting chasing in walls for concealed wiring using machine cutting and making good the disturbed surface complete all as specified and as directed. Note: 3 runs of 6 sqmm cable including earth wire & one run of PVC conduit shall be measured as single unit

Material and Labour for sub main wiring (concealed) complete with two single core 4 Sqmm FRLS PVC insulated unsheathed stranded copper conductor cable drawn through in and including 20 mm dia rigid non-metallic PVC conduit heavy grade and conduit accessories including 4 Sqmm FRLS PVC insulated unsheathed stranded copper earth cable connected to common earth dolly complete and including cutting chasing in walls for concealed wiring using machine cutting and making good the disturbed surface complete all as specified and as directed. Note: 3 runs of 4 sqmm cable including earth wire & one run of PVC conduit shall be measured as single unit.

Material and Labour for sub main wiring (Surface) complete with two single core 1.5 Sqmm FRLS PVC insulated unsheathed stranded copper conductor cable drawn through in and including 20 mm dia rigid non-metallic PVC conduit/Capping casing heavy grade and conduit accessories including 4 Sqmm FRLS PVC insulated unsheathed stranded copper earth cable connected to common earth dolly complete all as specified and as directed. Note: 3 runs of 1.5 sqmm cable including earth wire & one run of PVC conduit shall be measured as single unit

Taking down carefully any type point wiring (light, fans, socket etc) complete including battens and fittings such as switch, ceiling rose, light fittings, regulators, socket, etc. and making good disturbed surface to match the existing etc. complete all as specified and as directed.

Material and Labour for point wiring (concealed) on walls and surface on ceiling complete with FRLS PVC insulated unsheathed 1100 Volts grade, conforming to IS-694, 1.5 sq mm (nominal area) multi stranded copper conductor cable drawn though in and including non metallic medium grade rigid PVC conduit heavy grade accessories, ISI marked, 20 mm dia including all accessories, concealed in walls by cutting chases using machine and making good the disturbed surface with and including suitable sunken boxes for modular switch plates of suitable make in OMQ area and for hylam sheet with provision for fixing pendant type switch, sockets etc in SMQ area and 1.5 sq mm copper earth continuity wire connected to earth dolly complete for the following complete all as specified and as directed. (a) One light point controlled by one switch

(b) One fan point controlled by one switch

(c) One exhaust fan point controlled by one switch.

(d) One bell/ buzzer point controlled by one push switch.

(e) One switch socket outlet modular type 3 pin 6 amp on same board.

(f) One light point controlled by two, two way switches,

All as per item No 203 above but 1.5 sq mm cable size and 1.5 sq mm earth continuity wire for one 3 pin socket outlet, 6 amps on Independent board.

All as per item No 203 above but 2.5 sq mm cable size with 2.5 sq mm earth continuity wire for one 3 pin socket outlet, 16 Amps on independent board.

Supply and fixing LED security light fitting 25 W made out of pressure die cast aluminium powder coated housing high impact resistant 4 mm thick toughened glass cover and matrix of power LEDs in built electronic driver up to 4 KV surge protection fitted with adjustable pole adopter to enable on site tilt angle setting and input power 25 W system lumens 85/W operating voltage 160-260 V complete in all respect including supply and fix brackets made out of 25 mm dia GI medium grade tubing of suitable length and bend to shape including fixing MS flat iron clamps, bolts & nuts complete all as specified and as directed. Make : CG Cat Part No. LSTS-25-CDL or equivalent model of Havels/Philips

Supply, Installation, Testing and Commissioning of 10 Watt LED Bulkhead with a nominal system lumen output of 1000 lumens and a minimum system efficiency of 100 lm/W complete all as specified and as directed.

Supply & fix new master led tube 4ft 20 W LED batten of high-quality materials and design, Extruded aluminum housing enhances safety, High quality PC Diffuser. Reliable and robust housing structure having nominal system lumen output of 2500 lumens and a minimum system efficacy of 125 lm/W. The luminarie shall have a rated system lifetime of 50,000 burning hours at L70.The luminarie should have a color temperature of 6500K and CRI>83. The luminarie shall meet IP20 rating with THD < 10% and PF > 0.95. The total power consumption should not exceed 20W (including driver) complete all as specified and as directed.

Supply and fixing Surface mounting LED Luminaries and 1 x 10 Watt LED fitting with connecting up with copper 3 core flexible cord of minimum size 1.5 Sqmm size complete all as specified and as directed.

Supply and fixing Lamp holder, PVC/Polycarbonate type with cord grip cap suitable for pendant fittings complete all as specified and as directed.

Supply and fixing LED Bulb of 9 Watt with minimum luminarie of 100 Lm/W complete all as specified and as directed.

Supply and fixing 4 step type, one module, modular type electronic fan regulator for ceiling fan 1200 mm sweep, 240 volts, 100 Watts single pole, complete all as specified and as directed.

Supply and fixing calling bell ding dong type , AC, single pole one way 230 volts complete all as specified and as directed.

Supply and fixing bell push switch, modular type, 6 Amps, 1 module, 250 volts complete all as specified and as directed.

Supply and fixing switch modular type single pole two way 6 amps 250 volts, complete all as specified and as directed.

Supply and fixing Switch modular type, single pole one way 6 Amps, 250 volts Ac suitable for modular switch boxes without indicator, complete all as specified and as directed.

Supply and fixing socket modular type 6 Amps 3 pin 2 module 250 volts complete all as specified and as directed.

Supply and fixing ceiling rose, surface bakelite, 65 x 50 mm, two to three terminals complete all as specified and as directed.

Supply and fixing socket modular type 6/16 Amps, 3 pin combine, 2 module, 240 volts complete all as specified and as directed.

Supply and fixing switch modular type 16 Amps,one way with indicator, 1 module,240 volts complete all as specified and as directed.

Supply and fixing power unit for upto 2 ton AC and geyser up to 3.5 KW modular type , 4 module,240 volts complete all as specified and as directed.

Supply and fixing stepped type electronic fan regulator flush type for ceiling fan 1200 mm sweep, 240 volts, 100 Watts single pole, complete all as specified and as directed.

Supply and fixing bell push switch, flush type, 5 Amps, 250 volts complete all as specified and as directed.

Supply and fixing switch flush type single pole two way 16 amps 250 volts, complete all as specified and as directed.

Supply and fixing Switch piano, flush type, single pole one way 6 Amps, 250 volts AC, complete all as specified and as directed.

Supply and fixing socket flush type 6 Amps, 3 pin 250 volts complete all as specified and as directed.

Supply and fixing socket flush type 6/16 Amps, 3 pin combine, 240 volts complete all as specified and as directed.

Supply and fixing switch piano, flush type 16 Amps,one way with indicator, 240 volts complete all as specified and as directed.

Supply and fixing sheet metal enclosures for DB's for incorporating MCBs, TPN, 4 way, IP-43 with metal double door, 415 volts, as per IS-8623, complete all as specified and as directed.

Supply and fixing MCB TPN, 40-63 Amps, breaking capacity 10 KA 'C' curve confirming to IS/IEC 60898-1 2002,integrated label holder, sliding bottom clamp , IP 20 protected terminal, sliding shutters, 240 volts, 50 HZ including making necessary incoming and outgoing electrical connection with suitable size of copper lugs etc complete all as specified and as directed. Make : Legrand/Seimens/ABB

Supply and fixing sheet metal enclosures for SPN DB's with metal double door for incorporating MCBs,IP-43 , 8 way, 240 volts, as per IS-8623 complete all as specified and as directed. Make : Legrand/Seimens/ABB

Supply and fixing sheet metal enclosures for SPN DB's 2 way, 240 volts, as per IS-8623 complete all as specified and as directed. Make : Legrand/Seimens/ABB

Supply and fixing MCB SPN, 6-32 Amps, breaking capacity 10 KA 'C' curve confirming to IS/IEC 60898-1 2002,integrated label holder, sliding bottom clamp , IP 20 protected terminal, sliding shutters, 240 volts, 50 HZ including making necessary incoming and outgoing electrical connection with suitable size of copper lugs etc complete all as specified and as directed. Make : Legrand/Seimens/ABB

Supply and fixing MCB SP 6-32 Amps, breaking capacity 10 KA 'C' curve confirming to IS/IEC 60898-1 2002,integrated label holder, sliding bottom clamp , IP 20 protected terminal, sliding shutters, 240 volts, 50 HZ including making necessary incoming and outgoing electrical connection with suitable size of copper lugs etc complete all as specified and as directed. Make : Legrand/Seimens/ABB

Supply and fixing 'D' clamp after cutting the ceiling of roof and binding with reinforcement and making good with cement reinforcement and finishing with matching with existing surfaces, including anchor bolt having four nuts and washers for hanging of ceiling fans complete all as specified and as directed.

Material and Labour for earthing complete with galvanised steel plate electrode, 600 x 600 x 6 mm thick, buried directly in ground (earth pit not less than 2.25 mtrs deep below nominal ground level) with top edge of the plate not less than not less than 1.5 metres below nominal ground level connected to earthing lead of 4 mm dia galvanised iron or steel wire all as shown in plate No. 4 of SSR Part-I of 2009 to the earthing test point including necessary excavation and earth work in any type of soil, PCC 1:3:6 type C-2 pit and RCC1:2:4 type B-2 cover funnel & watering pipe 20mm dia GI medium grade, wiremesh, charcoal dust and common salt earth lead protection pipe 15mm dia light grade upto 7.5m complete all as specified and as directed.

Taking down fan of any size and any make, sealing cable end with insulation tape, dismantling the fan blade and removing fan and blade to store complete all as specified and as directed.

Hanging only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and as directed.

Supply and fixing New Energy saving ceiling fan 1200 mm sweep with double ball bearing in opal white colour and BEE 5 star rated BLDC type complete including provision of 3 core copper wire of size 1.5 sqmm , connected from ceiling rose to fan and marking MES No in black paint complete all as specified and as directed. Make : Havells/Bajaj/Orient/Crompton

Supply and fixing New Exhaust fan PVC body 10" ( 250 mm) sweep 230 V, 50 Hz, complete with all accessories & connector etc internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size, complete all as specified and as directed. Make : Havells/Bajaj/Orient/Crompton

Fixing only exhaust fan and connecting up including provision of cable from ceiling rose/connector to fan complete all as specified and as directed.

Supply and fixing Wall mounted fan of size 16" plastic body including all accessories and connected material complete all as specified and as directed. Make : Havells/Bajaj/Orient/Crompton

Taking down old geyser and depositing it to E/M store and Refixing the same at exact location including making electric and water connection complete all as specified and as directed.

Supply, fixing & testing of water heater storage vertical type of capacity 25 Ltrs, 5 Star rating, rated pressure of 8 bar, unique polymer coating tech, special titanium enamelled heating element of capacity upto 2 KW, special deflector alongwith grouting and fixing with suitable size of nuts and bolts fixing in the wall with PCC 1:2:4 type BI using 20 mm graded stone aggregate and making good the disturb surface including electric and water connection complete all as specified and as directed. Make : Racold/Bajaj/Usha/Crompton

Note : The amount against Schedule of Credit on Page No. 70 shall be deducted from the total amount quoted against Sch 'A' while deriving Contract Sum for Acceptance.

chronicle enterprises