Loading…
Loading…
Tender Value
₹2.7 Cr
EMD Value
₹5.5 L
Closing Date
10 Jun 2026, 12:00 pm4d left
Replacement of Old & Overaged Power Supply Lines and Other assets to improve reliability of power supply system in wayside sections under Sr.DEE(G)/KGP as Phase-1.
114-ELC-G-KGP-26-27-05
114-ELC-G-KGP-26-27-05
Open
12 Months
Unknown (Unspecified Location)
₹0
₹5.5 L
18 May 2026
18 May 2026
27 May 2026
Item Breakup - A-Work under SSEE/P/BLS.
Laying of LT cable/cables in underground Metre along the road through cable trench etc. as mentioned in explanatory note. PROJECT-KGP-ELECTRICAL/SOUTH EASTERN RLY
Laying of LT cable/cables across the road, Metre track, drain through RCC/GI pipe as mentioned in explanatory note.
Laying of LT cable/cables on wall/structure Metre through PVC casing pipe of size 4inches or 3inches with accessories as mentioned in explanatory note.
Laying of extra cables in the excavated same Metre trench.
Transportation of cables in drum/rolls with or Each without wooden drums/roll from the store of concerned SSEE or any store of Kharagpur Division to the site of works.
Supply, transportation and fixing of RCC Cable Numbers Route Marker of size L-12", B-6" and H-2.6" or as per site requirement with all accessories.
Supply, erection, testing and commissioning Set of LT XLPE cable gland made of Brass with aluminum lugs/sockets (4 Nos.) suitable for termination work of LT 4 Core X 16-25 sq. mm XLPE aluminum conductor armored cable.
Supply, erection, testing and commissioning Set of LT XLPE cable gland made of Brass with aluminum lugs/sockets (4 Nos.) suitable for termination work of LT 4 Core X 35-50 sq. mm XLPE aluminum conductor armored cable.
Supply, erection, testing and commissioning Set of LT XLPE cable gland made of Brass with aluminum lugs/sockets (4 Nos.) suitable for termination work of LT 4 Core X 70-95 sq. mm XLPE aluminum conductor armored cable.
Supply of 75mm Outer Dia. HDPE pipe of Metre Grade PE-100 with all accessories like suitable couplers, plugs, end caps, spacer, T band etc. as mentioned in explanatory note.
Erection and commissioning of HDPE pipe of Metre any size with all accessories to complete job.
Supply of 63A Copper Bus-bar Chamber Box Numbers provided with 6-ways, made of Polycarbonate/ Thermoplastic of size: 350 X 300 X 146 mm or above including 4 Nos. Cu Bus-bar of size- 15X3mm or above as approved by competent authority, 5 sets of brass cable glands suitable for 25-70 sq.mm Alm Armoured cable. The Box should have Ingress Protection of IP65 or better, Impact Protection of IK09 or better, with rust, dust, moisture and shock proof, anti-corrosive, fire retardant properties and hinged arrangement for easy operation.
Fixing & Commissioning of 63A Copper Bus- Numbers bar Chamber Box made of Polycarbonate/ Thermoplastic with 5 sets of brass cable glands suitable for 25-70 sq.mm Alm Armoured cable. Cost also includes fixing of the box in wall or electric pole with suitable fixing arrangement and proper termination and connection of cables to complete the job. PROJECT-KGP-ELECTRICAL/SOUTH EASTERN RLY
Supply of 100A Copper Bus-bar Chamber Box Numbers provided with 6-ways, made of Polycarbonate/ Thermoplastic of size: 450 X 300 X 210 mm or above including 4 Nos. Cu Bus-bar of size- 25X3mm or above as approved by competent authority, 5 sets of brass cable glands suitable for 35-95 sq.mm Alm Armoured cable. The Box should have Ingress Protection of IP65 or better, Impact Protection of IK09 or better, with rust, dust, moisture and shock proof, anti-corrosive, fire retardant properties and hinged arrangement for easy operation.
Fixing & Commissioning of 100A Copper Bus- Numbers bar Chamber Box made of Polycarbonate/ Thermoplastic with 5 sets of brass cable glands suitable for 35-95 sq.mm Alm Armoured cable. Cost also includes fixing of the box in wall or electric pole with suitable fixing arrangement and proper termination and connection of cables to complete the job.
Supply of 6M HDG (Hot Dip Galvanized) Numbers Octagonal Pole with cable junction compartment, Pole top dia. 70mm, bottom dia. 130mm, sheet thickness 3mm, base plate dimensions (L X B X T)-220mm X 220mm X 12mm with 500 mm long single/double arm and foundation bolts etc. as per specifications mentioned in explanatory note.
Supply of Insulated Cable Connector 4-way Set and SP 6A MCB, Type B- 01 No. along with Bakelite sheet for Octagonal Pole.
Fixing and Commissioning of 6M HDG (Hot Dip Numbers Galvanized) Octagonal Pole, top dia. 70mm, bottom dia. 130mm, sheet thickness 3mm, base plate dimensions (L X B X T)- 220mm X 220mm X 12mm with 500 mm long single/double arm and foundation bolts etc. with RCC foundation works to complete the job as per specifications mentioned in explanatory note.
Supply of LED 45 watt or higher wattage Numbers street light with Colour Rendering Index (CRI) >=70, confirming IP66 as per specifications mentioned in explanatory note.
Fixing and commissioning of LED 45 watt or Numbers higher wattage street light including wiring of light from loop box. PROJECT-KGP-ELECTRICAL/SOUTH EASTERN RLY
Supply with testing of Indoor Type LT Panel Set made of Powder Coated CRCA Sheet Steel of thickness (minimum): 2mm with Ingress Protection: IP 53 or higher consisting with 4- pole 250A 36kA microprocessor based MCCB - 01no. as incoming and 4-pole 160A 36kA microprocessor based MCCB -02nos, 4-pole 63A 36kA microprocessor based MCCB - 02nos, DP 32A, 10kA MCB with 2PP, Type B- 06nos. as outgoing with suitable Cu. Bus bar, Digital Multifunctional Meter in all Incoming & Outgoing MCCB, Capable to measure and display Voltage, Current, Frequency, Power factor, kW, kVAR, kWh, kVAh, kVARh etc., appropriate spreader link for MCCB, Automatic Fire Ball, Insulating Mats and with necessary item for seal the cable entry and outgoing point duly conforming PCEE/SER/GRC Specification of LT Distribution Panel as applicable with Description No. SER/ELEC/GS/ DESCRIPTION/LT PANEL/1/REV- 2/JUNE 2025, Dtd.16/06/2025. Location- for JER & ROP Switch Room or Any other suitable location as per consignee.
Fixing and commissioning of Indoor Type LT Set Panel made of Powder Coated CRCA Sheet Steel of thickness (minimum): 2mm with Ingress Protection: IP 53 or higher consisting with 4-pole 250A 36kA microprocessor based MCCB -01no. as incoming and 4-pole 160A 36kA microprocessor based MCCB -02nos, 4- pole 63A 36kA microprocessor based MCCB - 02nos, DP 32A, 10kA MCB with 2PP, Type B- 06nos. as outgoing with suitable Cu. Bus bar, Digital Multifunctional Meter in all Incoming & Outgoing MCCB, Capable to measure and display Voltage, Current, Frequency, Power factor, kW, kVAR, kWh, kVAh, kVARh etc., appropriate spreader link for MCCB, Automatic Fire Ball, Insulating Mats and with necessary item for seal the cable entry and outgoing point and all other Civil work and accessories to complete job.
Supply with testing of Indoor Type LT Panel Set made of Powder Coated CRCA Sheet Steel of thickness (minimum): 2mm with Ingress Protection: IP 53 or higher consisting with FP 160A, 36kA microprocessor based MCCB- 01 no. as incoming and FP 63A, 36kA microprocessor based MCCB- 03 nos., FP 32A, 10KA MCB with 4PP- 03 nos. as outgoing with suitable Cu. Bus bar, Digital Multifunctional Meter in all Incoming & Outgoing MCCB, Capable to measure and display Voltage, Current, Frequency, Power factor, kW, kVAR, kWh, kVAh, kVARh etc., appropriate spreader link for MCCB, Automatic Fire Ball, Insulating Mats and with necessary item for seal the cable entry and outgoing point duly conforming PCEE/SER/GRC Specification of LT Distribution Panel as applicable with Description No. SER/ELEC/GS/ DESCRIPTION/LT PANEL/1/REV-2/JUNE 2025, Dtd.16/06/2025. Location- for MKO & KHE Switch Room or Any other suitable location as per consignee. PROJECT-KGP-ELECTRICAL/SOUTH EASTERN RLY
Fixing and commissioning of Indoor Type LT Set Panel made of Powder Coated CRCA Sheet Steel of thickness (minimum): 2mm with Ingress Protection: IP 53 or higher consisting with FP 160A, 36kA microprocessor based MCCB- 01 no. as incoming and FP 63A, 36kA microprocessor based MCCB- 03 nos., FP 32A, 10KA MCB with 4PP- 03 nos. as outgoing with suitable Cu. Bus bar, Digital Multifunctional Meter in all Incoming & Outgoing MCCB, Capable to measure and display Voltage, Current, Frequency, Power factor, kW, kVAR, kWh, kVAh, kVARh etc., appropriate spreader link for MCCB, Automatic Fire Ball, Insulating Mats and with necessary item for seal the cable entry and outgoing point and all other Civil work and accessories to complete job.
Supply with testing of Outdoor Type LT Panel Set made of Powder Coated CRCA Sheet Steel of thickness (minimum): 2mm with Double Door arrangement (Front side openable & operatable compartmental doors and front side outer door is to be provided) to meet Ingress Protection of IP 65 or higher, a canopy at the top made of minimum 2.0mm thick CRCA Sheet Steel to protect panel from rainwater consisting of FP 250A, 36kA microprocessor based MCCB- 01 no. as incoming and FP 100A, 36kA microprocessor based MCCB- 2nos., FP 32A, 10KA MCB with 4PP- 03nos. as outgoing with suitable Cu. Bus bar, Digital Multifunctional Meter in each Incoming & Outgoing MCCB, Capable to measure and display Voltage, Current, Frequency, Power factor, kW, kVAR, kWh, kVAh, kVARh etc., appropriate spreader link for MCCB and with necessary item for seal the cable entry and outgoing point duly conforming PCEE/SER/GRC Specification of LT Distribution Panel as applicable with Description No. SER/ELEC/GS/DESCRIPTION/LT PANEL/1/REV-2/JUNE 2025, Dtd.16/06/2025.
Fixing and commissioning of Outdoor Type LT Set Panel made of Powder Coated CRCA Sheet Steel of thickness (minimum): 2mm with Double Door arrangement (Front side openable & operatable compartmental doors and front side outer door is to be provided) to meet Ingress Protection of IP 65 or higher, a canopy at the top made of minimum 2.0mm thick CRCA Sheet Steel to protect panel from rainwater consisting of FP 250A, 36kA microprocessor based MCCB- 01 no. as incoming and FP 100A, 36kA microprocessor based MCCB- 2nos., FP 32A, 10KA MCB with 4PP- 03nos. as outgoing with suitable Cu. Bus bar, Digital Multifunctional Meter in each Incoming & Outgoing MCCB, Capable to measure and display Voltage, Current, Frequency, Power factor, kW, kVAR, kWh, kVAh, kVARh etc., appropriate spreader link for MCCB and with necessary item for seal the cable entry and outgoing point and all other Civil work and accessories to complete job. PROJECT-KGP-ELECTRICAL/SOUTH EASTERN RLY
Supply with testing of Outdoor Type LT Panel Set made of Powder Coated CRCA Sheet Steel of thickness (minimum): 2mm with Double Door arrangement (Front side openable & operatable compartmental doors and front side outer door is to be provided) to meet Ingress Protection of IP 65 or higher, a canopy at the top made of minimum 2.0mm thick CRCA Sheet Steel to protect panel from rainwater consisting of FP 160A, 36kA microprocessor based MCCB- 01 no. as incoming and FP 63A, 36kA microprocessor based MCCB- 2nos., FP 32A, 10KA MCB with 4PP- 03nos. as outgoing with suitable Cu. Bus bar, Digital Multifunctional Meter in each Incoming & Outgoing MCCB, Capable to measure and display Voltage, Current, Frequency, Power factor, kW, kVAR, kWh, kVAh, kVARh etc., appropriate spreader link for MCCB and with necessary item for seal the cable entry and outgoing point duly conforming PCEE/SER/GRC Specification of LT Distribution Panel as applicable with Description No. SER/ELEC/GS/DESCRIPTION/LT PANEL/1/REV-2/JUNE 2025, Dtd.16/06/2025.
Fixing and commissioning of Outdoor Type LT Set Panel made of Powder Coated CRCA Sheet Steel of thickness (minimum): 2mm with Double Door arrangement (Front side openable & operatable compartmental doors and front side outer door is to be provided) to meet Ingress Protection of IP 65 or higher, a canopy at the top made of minimum 2.0mm thick CRCA Sheet Steel to protect panel from rainwater consisting of FP 160A, 36kA microprocessor based MCCB- 01 no. as incoming and FP 63A, 36kA microprocessor based MCCB- 2nos., FP 32A, 10KA MCB with 4PP- 03nos. as outgoing with suitable Cu. Bus bar, Digital Multifunctional Meter in each Incoming & Outgoing MCCB, Capable to measure and display Voltage, Current, Frequency, Power factor, kW, kVAR, kWh, kVAh, kVARh etc., appropriate spreader link for MCCB and with necessary item for seal the cable entry and outgoing point and all other Civil work and accessories to complete job.
Supply of FP 200 Amps, 36kA Microprocessor Numbers Based MCCB including spreader link and sheet steel powder painted enclosure of thickness (minimum): 1.6mm as mentioned in explanatory note.
Fixing and commissioning of FP 200 Amps Numbers MCCB with sheet steel powder painted enclosure as per site requirement to complete job.
Supply of FP 100 Amps, 36kA Microprocessor Numbers Based MCCB including spreader link and sheet steel powder painted enclosure of thickness (minimum): 1.6mm as mentioned in explanatory note.
Fixing and commissioning of FP 100 Amps Numbers MCCB with sheet steel powder painted enclosure as per site requirement to complete job. PROJECT-KGP-ELECTRICAL/SOUTH EASTERN RLY
Supply of Floor/Panel/Tower/Wall mounted 3- Numbers Phase Timer Panel, consisting of auto/manual switch, Digital Time Switch- 01no, FP Contactor Rating (A): 40A or above- 01 No. (with required number of NO and NC Contacts as per panel design), MCB Rating: FP 40A, 10kA MCB with 4PP (Protected Pole) as incoming, SP 20A, 10kA MCB with 1PP (Protected Pole) -06 Nos. as outgoing and SP 6A, 10kA MCB with 1PP (Protected Pole) -01 No. for control circuit protection with provision of pad lock, cable gland etc.
Fixing and commissioning of Timer Panel with Numbers all accessories. The panel should be mounted on 0.5mtr civil foundation along with 0.5mtr iron frame body to support the panel for water protection in case if it is floor mounted.
Supply, laying, fixing and commissioning of 25 Metre x 5mm GI strip as and where required extra for earth connection between earth electrode and main switch/ DB/ Electric pole etc. as per site supervisor's instruction, including connection & termination with stainless steel nut, bolt, spring, washer etc. as required.
Supply of Earthing arrangement with supply Each of Hot Dip Galvanized (HDG) earth cone and all other requisite materials as per CEE/GRC's Drg. No.CEE/G/A3/P-150, Alt.1 including sump box, cover with salt and charcoal etc. as per site supervisor's instruction. Cost includes supply of all materials mentioned in the Drawing including 02 meters 25 x 5mm GI strip for connection from earth electrode pipe to light pole /Rail pole etc.
Erection of Earthing arrangement with Each erection of Hot Dip Galvanized (HDG) earth cone and all other requisite materials as per CEE/GRC's Drg. No.CEE/G/A3/P-150, Alt.1 including sump box, cover with salt and charcoal etc. as per site supervisor's instruction. Cost includes erection of all materials mentioned in the Drawing including 02 meters 25 x 5mm GI strip for connection from earth electrode pipe to light pole /Rail pole etc.
Electric Pole cutting / dismantling and deposit Numbers in Consignee's Store.
Disconnection, Dismantling and Removal of Metre overhead bare conductor bunch (consisting with four / five / six conductors as per site), insulator & other all accessories from pole including transportation of released materials from site and handing over the same to Consignee's Store as per advice of the competent authority. Total 6546278.04
Item Breakup - B-Work under SSEE/P/MCA including HLZ & DGHA section.
Laying of LT cable/cables in underground Metre along the road through cable trench etc. as mentioned in explanatory note.
Laying of LT cable/cables across the road, Metre track, drain through RCC/GI pipe as mentioned in explanatory note. PROJECT-KGP-ELECTRICAL/SOUTH EASTERN RLY
Laying of LT cable/cables on wall/structure Metre through PVC casing pipe of size 4inches or 3inches with accessories as mentioned in explanatory note.
Laying of extra cables in the excavated same Metre trench.
Transportation of cables in drum/rolls with or Each without wooden drums/roll from the store of concerned SSEE or any store of Kharagpur Division to the site of works.
Supply, transportation and fixing of RCC Cable Numbers Route Marker of size L-12", B-6" and H-2.6" or as per site requirement with all accessories.
Supply, erection, testing and commissioning Set of LT XLPE cable gland made of Brass with aluminum lugs/sockets (4 Nos.) suitable for termination work of LT 4 Core X 16-25 sq. mm XLPE aluminum conductor armored cable.
Supply, erection, testing and commissioning Set of LT XLPE cable gland made of Brass with aluminum lugs/sockets (4 Nos.) suitable for termination work of LT 4 Core X 35-50 sq. mm XLPE aluminum conductor armored cable.
Supply, erection, testing and commissioning Set of LT XLPE cable gland made of Brass with aluminum lugs/sockets (4 Nos.) suitable for termination work of LT 4 Core X 70-95 sq. mm XLPE aluminum conductor armored cable.
Supply, erection, testing and commissioning Set of LT XLPE cable gland made of Brass with aluminum lugs/sockets (4 Nos.) suitable for termination work of LT 4 Core X 120-150 sq. mm XLPE aluminum conductor armored cable.
Supply of 75mm Outer Dia. HDPE pipe of Metre Grade PE-100 with all accessories like suitable couplers, plugs, end caps, spacer, T band etc. as mentioned in explanatory note.
Erection and commissioning of HDPE pipe of Metre any size with all accessories to complete job.
Supply of 63A Copper Bus-bar Chamber Box Numbers provided with 6-ways, made of Polycarbonate/ Thermoplastic of size: 350 X 300 X 146 mm or above including 4 Nos. Cu Bus-bar of size- 15X3mm or above as approved by competent authority, 5 sets of brass cable glands suitable for 25-70 sq.mm Alm Armoured cable. The Box should have Ingress Protection of IP65 or better, Impact Protection of IK09 or better, with rust, dust, moisture and shock proof, anti-corrosive, fire retardant properties and hinged arrangement for easy operation.
Fixing & Commissioning of 63A Copper Bus- Numbers bar Chamber Box made of Polycarbonate/ Thermoplastic with 5 sets of brass cable glands suitable for 25-70 sq.mm Alm Armoured cable. Cost also includes fixing of the box in wall or electric pole with suitable fixing arrangement and proper termination and connection of cables to complete the job. PROJECT-KGP-ELECTRICAL/SOUTH EASTERN RLY
Supply of 100A Copper Bus-bar Chamber Box Numbers provided with 6-ways, made of Polycarbonate/ Thermoplastic of size: 450 X 300 X 210 mm or above including 4 Nos. Cu Bus-bar of size- 25X3mm or above as approved by competent authority, 5 sets of brass cable glands suitable for 35-95 sq.mm Alm Armoured cable. The Box should have Ingress Protection of IP65 or better, Impact Protection of IK09 or better, with rust, dust, moisture and shock proof, anti-corrosive, fire retardant properties and hinged arrangement for easy operation.
Fixing & Commissioning of 100A Copper Bus- Numbers bar Chamber Box made of Polycarbonate/ Thermoplastic with 5 sets of brass cable glands suitable for 35-95 sq.mm Alm Armoured cable. Cost also includes fixing of the box in wall or electric pole with suitable fixing arrangement and proper termination and connection of cables to complete the job.
Supply of 5M HDG (Hot Dip Galvanized) Numbers Octagonal Pole with cable junction compartment, Pole top dia. 70mm, bottom dia. 130mm, sheet thickness 3mm, base plate dimensions (L X B X T)-200mm X 200mm X 12mm with 500 mm long single/double arm and foundation bolts etc. as per specifications mentioned in explanatory note.
Supply of Insulated Cable Connector 4-way Set and SP 6A MCB, Type B- 01 No. along with Bakelite sheet for Octagonal Pole.
Fixing and Commissioning of 5M HDG (Hot Dip Numbers Galvanized) Octagonal Pole, top dia. 70mm, bottom dia. 130mm, sheet thickness 3mm, base plate dimensions (L X B X T)- 200mm X 200mm X 12mm with 500 mm long single/double arm and foundation bolts etc. with RCC foundation works to complete the job as per specifications mentioned in explanatory note.
Supply of LED 45 watt or higher wattage Numbers street light with Colour Rendering Index (CRI) >=70, confirming IP66 as per specifications mentioned in explanatory note.
Fixing and commissioning of LED 45 watt or Numbers higher wattage street light including wiring of light from loop box. PROJECT-KGP-ELECTRICAL/SOUTH EASTERN RLY
Supply with testing of Indoor Type LT Panel Set made of Powder Coated CRCA Sheet Steel of thickness (minimum): 2mm with Ingress Protection: IP 53 or higher consisting with 4- pole 400A 50kA microprocessor based MCCB - 01nos as incoming and 4-pole 160A 36kA microprocessor based MCCB -04nos, 4-pole 100A 36kA microprocessor based MCCB - 02nos and 4-pole 63A, 10kA MCB with 4PP - 02nos as outgoing with suitable Cu. Bus bar, Digital Multifunctional Meter in all Incoming & Outgoing MCCB, Capable to measure and display Voltage, Current, Frequency, Power factor, kW, kVAR, kWh, kVAh, kVARh etc., appropriate spreader link for MCCB, Automatic Fire Ball, Insulating Mats and with necessary item for seal the cable entry and outgoing point duly conforming PCEE/SER/GRC Specification of LT Distribution Panel as applicable with Description No. SER/ELEC/GS/ DESCRIPTION/LT PANEL/1/REV- 2/JUNE 2025, Dtd.16/06/2025. Location- for KIG RRN Colony Switch Room or Any other suitable location as per consignee.
Fixing and commissioning of Indoor Type LT Set Panel made of Powder Coated CRCA Sheet Steel of thickness (minimum): 2mm with Ingress Protection: IP 53 or higher consisting with 4-pole 400A 50kA microprocessor based MCCB -01nos as incoming and 4-pole 160A 36kA microprocessor based MCCB -04nos, 4- pole 100A 36kA microprocessor based MCCB - 02nos and 4-pole 63A, 10kA MCB with 4PP - 02nos as outgoing with suitable Cu. Bus bar, Digital Multifunctional Meter in all Incoming & Outgoing MCCB, Capable to measure and display Voltage, Current, Frequency, Power factor, kW, kVAR, kWh, kVAh, kVARh etc., appropriate spreader link for MCCB, Automatic Fire Ball, Insulating Mats and with necessary item for seal the cable entry and outgoing point and all other Civil work and accessories to complete job.
Supply with testing of Indoor Type LT Panel Set made of Powder Coated CRCA Sheet Steel of thickness (minimum): 2mm with Ingress Protection: IP 53 or higher consisting with 4- pole 250A 36kA microprocessor based MCCB - 01no. as incoming and 4-pole 160A 36kA microprocessor based MCCB -02nos, 4-pole 63A 36kA microprocessor based MCCB - 02nos, DP 32A, 10kA MCB with 2PP, Type B- 06nos. as outgoing with suitable Cu. Bus bar, Digital Multifunctional Meter in all Incoming & Outgoing MCCB, Capable to measure and display Voltage, Current, Frequency, Power factor, kW, kVAR, kWh, kVAh, kVARh etc., appropriate spreader link for MCCB, Automatic Fire Ball, Insulating Mats and with necessary item for seal the cable entry and outgoing point duly conforming PCEE/SER/GRC Specification of LT Distribution Panel as applicable with Description No. SER/ELEC/GS/ DESCRIPTION/LT PANEL/1/REV- 2/JUNE 2025, Dtd.16/06/2025. Location- for KIG Station Switch Room or Any other suitable location as per consignee. PROJECT-KGP-ELECTRICAL/SOUTH EASTERN RLY
Fixing and commissioning of Indoor Type LT Set Panel made of Powder Coated CRCA Sheet Steel of thickness (minimum): 2mm with Ingress Protection: IP 53 or higher consisting with 4-pole 250A 36kA microprocessor based MCCB -01no. as incoming and 4-pole 160A 36kA microprocessor based MCCB -02nos, 4- pole 63A 36kA microprocessor based MCCB - 02nos, DP 32A, 10kA MCB with 2PP, Type B- 06nos. as outgoing with suitable Cu. Bus bar, Digital Multifunctional Meter in all Incoming & Outgoing MCCB, Capable to measure and display Voltage, Current, Frequency, Power factor, kW, kVAR, kWh, kVAh, kVARh etc., appropriate spreader link for MCCB, Automatic Fire Ball, Insulating Mats and with necessary item for seal the cable entry and outgoing point and all other Civil work and accessories to complete job.
Supply with testing of Indoor Type LT Panel Set made of Powder Coated CRCA Sheet Steel of thickness (minimum): 2mm with Ingress Protection: IP 53 or higher consisting with FP 160A, 36kA microprocessor based MCCB- 01 no. as incoming and FP 63A, 36kA microprocessor based MCCB- 03 nos., FP 32A, 10KA MCB with 4PP- 03 nos. as outgoing with suitable Cu. Bus bar, Digital Multifunctional Meter in all Incoming & Outgoing MCCB, Capable to measure and display Voltage, Current, Frequency, Power factor, kW, kVAR, kWh, kVAh, kVARh etc., appropriate spreader link for MCCB, Automatic Fire Ball, Insulating Mats and with necessary item for seal the cable entry and outgoing point duly conforming PCEE/SER/GRC Specification of LT Distribution Panel as applicable with Description No. SER/ELEC/GS/ DESCRIPTION/LT PANEL/1/REV-2/JUNE 2025, Dtd.16/06/2025. Location- for DTE, BOP, DZK, NDKR & DSPN Switch Room or Any other suitable location as per consignee.
Fixing and commissioning of Indoor Type LT Set Panel made of Powder Coated CRCA Sheet Steel of thickness (minimum): 2mm with Ingress Protection: IP 53 or higher consisting with FP 160A, 36kA microprocessor based MCCB- 01 no. as incoming and FP 63A, 36kA microprocessor based MCCB- 03 nos., FP 32A, 10KA MCB with 4PP- 03 nos. as outgoing with suitable Cu. Bus bar, Digital Multifunctional Meter in all Incoming & Outgoing MCCB, Capable to measure and display Voltage, Current, Frequency, Power factor, kW, kVAR, kWh, kVAh, kVARh etc., appropriate spreader link for MCCB, Automatic Fire Ball, Insulating Mats and with necessary item for seal the cable entry and outgoing point and all other Civil work and accessories to complete job. PROJECT-KGP-ELECTRICAL/SOUTH EASTERN RLY
Supply with testing of Outdoor Type LT Panel Set made of Powder Coated CRCA Sheet Steel of thickness (minimum): 2mm with Double Door arrangement (Front side openable & operatable compartmental doors and front side outer door is to be provided) to meet Ingress Protection of IP 65 or higher, a canopy at the top made of minimum 2.0mm thick CRCA Sheet Steel to protect panel from rainwater consisting of FP 250A, 36kA microprocessor based MCCB- 01 no. as incoming and FP 100A, 36kA microprocessor based MCCB- 2nos., FP 32A, 10KA MCB with 4PP- 03nos. as outgoing with suitable Cu. Bus bar, Digital Multifunctional Meter in each Incoming & Outgoing MCCB, Capable to measure and display Voltage, Current, Frequency, Power factor, kW, kVAR, kWh, kVAh, kVARh etc., appropriate spreader link for MCCB and with necessary item for seal the cable entry and outgoing point duly conforming PCEE/SER/GRC Specification of LT Distribution Panel as applicable with Description No. SER/ELEC/GS/DESCRIPTION/LT PANEL/1/REV-2/JUNE 2025, Dtd.16/06/2025.
Fixing and commissioning of Outdoor Type LT Set Panel made of Powder Coated CRCA Sheet Steel of thickness (minimum): 2mm with Double Door arrangement (Front side openable & operatable compartmental doors and front side outer door is to be provided) to meet Ingress Protection of IP 65 or higher, a canopy at the top made of minimum 2.0mm thick CRCA Sheet Steel to protect panel from rainwater consisting of FP 250A, 36kA microprocessor based MCCB- 01 no. as incoming and FP 100A, 36kA microprocessor based MCCB- 2nos., FP 32A, 10KA MCB with 4PP- 03nos. as outgoing with suitable Cu. Bus bar, Digital Multifunctional Meter in each Incoming & Outgoing MCCB, Capable to measure and display Voltage, Current, Frequency, Power factor, kW, kVAR, kWh, kVAh, kVARh etc., appropriate spreader link for MCCB and with necessary item for seal the cable entry and outgoing point and all other Civil work and accessories to complete job. PROJECT-KGP-ELECTRICAL/SOUTH EASTERN RLY
Supply with testing of Outdoor Type LT Panel Set made of Powder Coated CRCA Sheet Steel of thickness (minimum): 2mm with Double Door arrangement (Front side openable & operatable compartmental doors and front side outer door is to be provided) to meet Ingress Protection of IP 65 or higher, a canopy at the top made of minimum 2.0mm thick CRCA Sheet Steel to protect panel from rainwater consisting of FP 160A, 36kA microprocessor based MCCB- 01 no. as incoming and FP 63A, 36kA microprocessor based MCCB- 2nos., FP 32A, 10KA MCB with 4PP- 03nos. as outgoing with suitable Cu. Bus bar, Digital Multifunctional Meter in each Incoming & Outgoing MCCB, Capable to measure and display Voltage, Current, Frequency, Power factor, kW, kVAR, kWh, kVAh, kVARh etc., appropriate spreader link for MCCB and with necessary item for seal the cable entry and outgoing point duly conforming PCEE/SER/GRC Specification of LT Distribution Panel as applicable with Description No. SER/ELEC/GS/DESCRIPTION/LT PANEL/1/REV-2/JUNE 2025, Dtd.16/06/2025.
Fixing and commissioning of Outdoor Type LT Set Panel made of Powder Coated CRCA Sheet Steel of thickness (minimum): 2mm with Double Door arrangement (Front side openable & operatable compartmental doors and front side outer door is to be provided) to meet Ingress Protection of IP 65 or higher, a canopy at the top made of minimum 2.0mm thick CRCA Sheet Steel to protect panel from rainwater consisting of FP 160A, 36kA microprocessor based MCCB- 01 no. as incoming and FP 63A, 36kA microprocessor based MCCB- 2nos., FP 32A, 10KA MCB with 4PP- 03nos. as outgoing with suitable Cu. Bus bar, Digital Multifunctional Meter in each Incoming & Outgoing MCCB, Capable to measure and display Voltage, Current, Frequency, Power factor, kW, kVAR, kWh, kVAh, kVARh etc., appropriate spreader link for MCCB and with necessary item for seal the cable entry and outgoing point and all other Civil work and accessories to complete job.
Supply of FP 200 Amps, 36kA Microprocessor Numbers Based MCCB including spreader link and sheet steel powder painted enclosure of thickness (minimum): 1.6mm as mentioned in explanatory note.
Fixing and commissioning of FP 200 Amps Numbers MCCB with sheet steel powder painted enclosure as per site requirement to complete job.
Supply of FP 100 Amps, 36kA Microprocessor Numbers Based MCCB including spreader link and sheet steel powder painted enclosure of thickness (minimum): 1.6mm as mentioned in explanatory note.
Fixing and commissioning of FP 100 Amps Numbers MCCB with sheet steel powder painted enclosure as per site requirement to complete job. PROJECT-KGP-ELECTRICAL/SOUTH EASTERN RLY
Supply of Floor/Panel/Tower/Wall mounted 3- Numbers Phase Timer Panel, consisting of auto/manual switch, Digital Time Switch- 01no, FP Contactor Rating (A): 40A or above- 01 No. (with required number of NO and NC Contacts as per panel design), MCB Rating: FP 40A, 10kA MCB with 4PP (Protected Pole) as incoming, SP 20A, 10kA MCB with 1PP (Protected Pole) -06 Nos. as outgoing and SP 6A, 10kA MCB with 1PP (Protected Pole) -01 No. for control circuit protection with provision of pad lock, cable gland etc.
Fixing and commissioning of Timer Panel with Numbers all accessories. The panel should be mounted on 0.5mtr civil foundation along with 0.5mtr iron frame body to support the panel for water protection in case if it is floor mounted.
Supply, laying, fixing and commissioning of 25 Metre x 5mm GI strip as and where required extra for earth connection between earth electrode and main switch/ DB/ Electric pole etc. as per site supervisor's instruction, including connection & termination with stainless steel nut, bolt, spring, washer etc. as required.
Supply of Earthing arrangement with supply Each of Hot Dip Galvanized (HDG) earth cone and all other requisite materials as per CEE/GRC's Drg. No.CEE/G/A3/P-150, Alt.1 including sump box, cover with salt and charcoal etc. as per site supervisor's instruction. Cost includes supply of all materials mentioned in the Drawing including 02 meters 25 x 5mm GI strip for connection from earth electrode pipe to light pole /Rail pole etc.
Erection of Earthing arrangement with Each erection of Hot Dip Galvanized (HDG) earth cone and all other requisite materials as per CEE/GRC's Drg. No.CEE/G/A3/P-150, Alt.1 including sump box, cover with salt and charcoal etc. as per site supervisor's instruction. Cost includes erection of all materials mentioned in the Drawing including 02 meters 25 x 5mm GI strip for connection from earth electrode pipe to light pole /Rail pole etc.
Electric Pole cutting / dismantling and deposit Numbers in Consignee's Store.
Disconnection, Dismantling and Removal of Metre overhead bare conductor bunch (consisting with four / five / six conductors as per site), insulator & other all accessories from pole including transportation of released materials from site and handing over the same to Consignee's Store as per advice of the competent authority. Total 15033067.89
Item Breakup - C-Work under SSEE/P/GII.
Laying of LT cable/cables in underground Metre along the road through cable trench etc. as mentioned in explanatory note.
Laying of LT cable/cables across the road, Metre track, drain through RCC/GI pipe as mentioned in explanatory note. PROJECT-KGP-ELECTRICAL/SOUTH EASTERN RLY
Laying of LT cable/cables on wall/structure Metre through PVC casing pipe of size 4inches or 3inches with accessories as mentioned in explanatory note.
Laying of extra cables in the excavated same Metre trench.
Transportation of cables in drum/rolls with or Each without wooden drums/roll from the store of concerned SSEE or any store of Kharagpur Division to the site of works.
Supply, transportation and fixing of RCC Cable Numbers Route Marker of size L-12", B-6" and H-2.6" or as per site requirement with all accessories.
Supply, erection, testing and commissioning Set of LT XLPE cable gland made of Brass with aluminum lugs/sockets (4 Nos.) suitable for termination work of LT 4 Core X 16-25 sq. mm XLPE aluminum conductor armored cable.
Supply, erection, testing and commissioning Set of LT XLPE cable gland made of Brass with aluminum lugs/sockets (4 Nos.) suitable for termination work of LT 4 Core X 35-50 sq. mm XLPE aluminum conductor armored cable.
Supply, erection, testing and commissioning Set of LT XLPE cable gland made of Brass with aluminum lugs/sockets (4 Nos.) suitable for termination work of LT 4 Core X 70-95 sq. mm XLPE aluminum conductor armored cable.
Supply of 75mm Outer Dia. HDPE pipe of Metre Grade PE-100 with all accessories like suitable couplers, plugs, end caps, spacer, T band etc. as mentioned in explanatory note.
Erection and commissioning of HDPE pipe of Metre any size with all accessories to complete job.
Supply of 63A Copper Bus-bar Chamber Box Numbers provided with 6-ways, made of Polycarbonate/ Thermoplastic of size: 350 X 300 X 146 mm or above including 4 Nos. Cu Bus-bar of size- 15X3mm or above as approved by competent authority, 5 sets of brass cable glands suitable for 25-70 sq.mm Alm Armoured cable. The Box should have Ingress Protection of IP65 or better, Impact Protection of IK09 or better, with rust, dust, moisture and shock proof, anti-corrosive, fire retardant properties and hinged arrangement for easy operation.
Fixing & Commissioning of 63A Copper Bus- Numbers bar Chamber Box made of Polycarbonate/ Thermoplastic with 5 sets of brass cable glands suitable for 25-70 sq.mm Alm Armoured cable. Cost also includes fixing of the box in wall or electric pole with suitable fixing arrangement and proper termination and connection of cables to complete the job.
Supply of 100A Copper Bus-bar Chamber Box Numbers provided with 6-ways, made of Polycarbonate/ Thermoplastic of size: 450 X 300 X 210 mm or above including 4 Nos. Cu Bus-bar of size- 25X3mm or above as approved by competent authority, 5 sets of brass cable glands suitable for 35-95 sq.mm Alm Armoured cable. The Box should have Ingress Protection of IP65 or better, Impact Protection of IK09 or better, with rust, dust, moisture and shock proof, anti-corrosive, fire retardant properties and hinged arrangement for easy operation. PROJECT-KGP-ELECTRICAL/SOUTH EASTERN RLY
Fixing & Commissioning of 100A Copper Bus- Numbers bar Chamber Box made of Polycarbonate/ Thermoplastic with 5 sets of brass cable glands suitable for 35-95 sq.mm Alm Armoured cable. Cost also includes fixing of the box in wall or electric pole with suitable fixing arrangement and proper termination and connection of cables to complete the job.
Supply of 5M HDG (Hot Dip Galvanized) Numbers Octagonal Pole with cable junction compartment, Pole top dia. 70mm, bottom dia. 130mm, sheet thickness 3mm, base plate dimensions (L X B X T)-200mm X 200mm X 12mm with 500 mm long single/double arm and foundation bolts etc. as per specifications mentioned in explanatory note.
Supply of Insulated Cable Connector 4-way Set and SP 6A MCB, Type B- 01 No. along with Bakelite sheet for Octagonal Pole.
Fixing and Commissioning of 5M HDG (Hot Dip Numbers Galvanized) Octagonal Pole, top dia. 70mm, bottom dia. 130mm, sheet thickness 3mm, base plate dimensions (L X B X T)- 200mm X 200mm X 12mm with 500 mm long single/double arm and foundation bolts etc. with RCC foundation works to complete the job as per specifications mentioned in explanatory note.
Supply of LED 45 watt or higher wattage Numbers street light with Colour Rendering Index (CRI) >=70, confirming IP66 as per specifications mentioned in explanatory note.
Fixing and commissioning of LED 45 watt or Numbers higher wattage street light including wiring of light from loop box.
Supply with testing of Indoor Type LT Panel Set made of Powder Coated CRCA Sheet Steel of thickness (minimum): 2mm with Ingress Protection: IP 53 or higher consisting with 4- pole 400A 50kA microprocessor based MCCB - 01nos as incoming and 4-pole 160A 36kA microprocessor based MCCB -04nos, 4-pole 100A 36kA microprocessor based MCCB - 02nos and 4-pole 63A, 10kA MCB with 4PP - 02nos as outgoing with suitable Cu. Bus bar, Digital Multifunctional Meter in all Incoming & Outgoing MCCB, Capable to measure and display Voltage, Current, Frequency, Power factor, kW, kVAR, kWh, kVAh, kVARh etc., appropriate spreader link for MCCB, Automatic Fire Ball, Insulating Mats and with necessary item for seal the cable entry and outgoing point duly conforming PCEE/SER/GRC Specification of LT Distribution Panel as applicable with Description No. SER/ELEC/GS/ DESCRIPTION/LT PANEL/1/REV- 2/JUNE 2025, Dtd.16/06/2025. Location- for JGM Switch Room or Any other suitable location as per consignee. PROJECT-KGP-ELECTRICAL/SOUTH EASTERN RLY
Fixing and commissioning of Indoor Type LT Set Panel made of Powder Coated CRCA Sheet Steel of thickness (minimum): 2mm with Ingress Protection: IP 53 or higher consisting with 4-pole 400A 50kA microprocessor based MCCB -01nos as incoming and 4-pole 160A 36kA microprocessor based MCCB -04nos, 4- pole 100A 36kA microprocessor based MCCB - 02nos and 4-pole 63A, 10kA MCB with 4PP - 02nos as outgoing with suitable Cu. Bus bar, Digital Multifunctional Meter in all Incoming & Outgoing MCCB, Capable to measure and display Voltage, Current, Frequency, Power factor, kW, kVAR, kWh, kVAh, kVARh etc., appropriate spreader link for MCCB, Automatic Fire Ball, Insulating Mats and with necessary item for seal the cable entry and outgoing point and all other Civil work and accessories to complete job.
Supply with testing of Indoor Type LT Panel Set made of Powder Coated CRCA Sheet Steel of thickness (minimum): 2mm with Ingress Protection: IP 53 or higher consisting with 4- pole 250A 36kA microprocessor based MCCB - 01no. as incoming and 4-pole 160A 36kA microprocessor based MCCB -02nos, 4-pole 63A 36kA microprocessor based MCCB - 02nos, DP 32A, 10kA MCB with 2PP, Type B- 06nos. as outgoing with suitable Cu. Bus bar, Digital Multifunctional Meter in all Incoming & Outgoing MCCB, Capable to measure and display Voltage, Current, Frequency, Power factor, kW, kVAR, kWh, kVAh, kVARh etc., appropriate spreader link for MCCB, Automatic Fire Ball, Insulating Mats and with necessary item for seal the cable entry and outgoing point duly conforming PCEE/SER/GRC Specification of LT Distribution Panel as applicable with Description No. SER/ELEC/GS/ DESCRIPTION/LT PANEL/1/REV- 2/JUNE 2025, Dtd.16/06/2025. Location- for CKU Switch Room or Any other suitable location as per consignee.
Fixing and commissioning of Indoor Type LT Set Panel made of Powder Coated CRCA Sheet Steel of thickness (minimum): 2mm with Ingress Protection: IP 53 or higher consisting with 4-pole 250A 36kA microprocessor based MCCB -01no. as incoming and 4-pole 160A 36kA microprocessor based MCCB -02nos, 4- pole 63A 36kA microprocessor based MCCB - 02nos, DP 32A, 10kA MCB with 2PP, Type B- 06nos. as outgoing with suitable Cu. Bus bar, Digital Multifunctional Meter in all Incoming & Outgoing MCCB, Capable to measure and display Voltage, Current, Frequency, Power factor, kW, kVAR, kWh, kVAh, kVARh etc., appropriate spreader link for MCCB, Automatic Fire Ball, Insulating Mats and with necessary item for seal the cable entry and outgoing point and all other Civil work and accessories to complete job. PROJECT-KGP-ELECTRICAL/SOUTH EASTERN RLY
Supply with testing of Outdoor Type LT Panel Set made of Powder Coated CRCA Sheet Steel of thickness (minimum): 2mm with Double Door arrangement (Front side openable & operatable compartmental doors and front side outer door is to be provided) to meet Ingress Protection of IP 65 or higher, a canopy at the top made of minimum 2.0mm thick CRCA Sheet Steel to protect panel from rainwater consisting of FP 250A, 36kA microprocessor based MCCB- 01 no. as incoming and FP 100A, 36kA microprocessor based MCCB- 2nos., FP 32A, 10KA MCB with 4PP- 03nos. as outgoing with suitable Cu. Bus bar, Digital Multifunctional Meter in each Incoming & Outgoing MCCB, Capable to measure and display Voltage, Current, Frequency, Power factor, kW, kVAR, kWh, kVAh, kVARh etc., appropriate spreader link for MCCB and with necessary item for seal the cable entry and outgoing point duly conforming PCEE/SER/GRC Specification of LT Distribution Panel as applicable with Description No. SER/ELEC/GS/DESCRIPTION/LT PANEL/1/REV-2/JUNE 2025, Dtd.16/06/2025.
Fixing and commissioning of Outdoor Type LT Set Panel made of Powder Coated CRCA Sheet Steel of thickness (minimum): 2mm with Double Door arrangement (Front side openable & operatable compartmental doors and front side outer door is to be provided) to meet Ingress Protection of IP 65 or higher, a canopy at the top made of minimum 2.0mm thick CRCA Sheet Steel to protect panel from rainwater consisting of FP 250A, 36kA microprocessor based MCCB- 01 no. as incoming and FP 100A, 36kA microprocessor based MCCB- 2nos., FP 32A, 10KA MCB with 4PP- 03nos. as outgoing with suitable Cu. Bus bar, Digital Multifunctional Meter in each Incoming & Outgoing MCCB, Capable to measure and display Voltage, Current, Frequency, Power factor, kW, kVAR, kWh, kVAh, kVARh etc., appropriate spreader link for MCCB and with necessary item for seal the cable entry and outgoing point and all other Civil work and accessories to complete job. PROJECT-KGP-ELECTRICAL/SOUTH EASTERN RLY
Supply with testing of Outdoor Type LT Panel Set made of Powder Coated CRCA Sheet Steel of thickness (minimum): 2mm with Double Door arrangement (Front side openable & operatable compartmental doors and front side outer door is to be provided) to meet Ingress Protection of IP 65 or higher, a canopy at the top made of minimum 2.0mm thick CRCA Sheet Steel to protect panel from rainwater consisting of FP 160A, 36kA microprocessor based MCCB- 01 no. as incoming and FP 63A, 36kA microprocessor based MCCB- 2nos., FP 32A, 10KA MCB with 4PP- 03nos. as outgoing with suitable Cu. Bus bar, Digital Multifunctional Meter in each Incoming & Outgoing MCCB, Capable to measure and display Voltage, Current, Frequency, Power factor, kW, kVAR, kWh, kVAh, kVARh etc., appropriate spreader link for MCCB and with necessary item for seal the cable entry and outgoing point duly conforming PCEE/SER/GRC Specification of LT Distribution Panel as applicable with Description No. SER/ELEC/GS/DESCRIPTION/LT PANEL/1/REV-2/JUNE 2025, Dtd.16/06/2025.
Fixing and commissioning of Outdoor Type LT Set Panel made of Powder Coated CRCA Sheet Steel of thickness (minimum): 2mm with Double Door arrangement (Front side openable & operatable compartmental doors and front side outer door is to be provided) to meet Ingress Protection of IP 65 or higher, a canopy at the top made of minimum 2.0mm thick CRCA Sheet Steel to protect panel from rainwater consisting of FP 160A, 36kA microprocessor based MCCB- 01 no. as incoming and FP 63A, 36kA microprocessor based MCCB- 2nos., FP 32A, 10KA MCB with 4PP- 03nos. as outgoing with suitable Cu. Bus bar, Digital Multifunctional Meter in each Incoming & Outgoing MCCB, Capable to measure and display Voltage, Current, Frequency, Power factor, kW, kVAR, kWh, kVAh, kVARh etc., appropriate spreader link for MCCB and with necessary item for seal the cable entry and outgoing point and all other Civil work and accessories to complete job.
Supply of Floor/Panel/Tower/Wall mounted 3- Numbers Phase Timer Panel, consisting of auto/manual switch, Digital Time Switch- 01no, FP Contactor Rating (A): 40A or above- 01 No. (with required number of NO and NC Contacts as per panel design), MCB Rating: FP 40A, 10kA MCB with 4PP (Protected Pole) as incoming, SP 20A, 10kA MCB with 1PP (Protected Pole) -06 Nos. as outgoing and SP 6A, 10kA MCB with 1PP (Protected Pole) -01 No. for control circuit protection with provision of pad lock, cable gland etc.
Fixing and commissioning of Timer Panel with Numbers all accessories. The panel should be mounted on 0.5mtr civil foundation along with 0.5mtr iron frame body to support the panel for water protection in case if it is floor mounted. PROJECT-KGP-ELECTRICAL/SOUTH EASTERN RLY
Supply, laying, fixing and commissioning of 25 Metre x 5mm GI strip as and where required extra for earth connection between earth electrode and main switch/ DB/ Electric pole etc. as per site supervisor's instruction, including connection & termination with stainless steel nut, bolt, spring, washer etc. as required.
Supply of Earthing arrangement with supply Each of Hot Dip Galvanized (HDG) earth cone and all other requisite materials as per CEE/GRC's Drg. No.CEE/G/A3/P-150, Alt.1 including sump box, cover with salt and charcoal etc. as per site supervisor's instruction. Cost includes supply of all materials mentioned in the Drawing including 02 meters 25 x 5mm GI strip for connection from earth electrode pipe to light pole /Rail pole etc.
Erection of Earthing arrangement with Each erection of Hot Dip Galvanized (HDG) earth cone and all other requisite materials as per CEE/GRC's Drg. No.CEE/G/A3/P-150, Alt.1 including sump box, cover with salt and charcoal etc. as per site supervisor's instruction. Cost includes erection of all materials mentioned in the Drawing including 02 meters 25 x 5mm GI strip for connection from earth electrode pipe to light pole /Rail pole etc.
Electric Pole cutting / dismantling and deposit Numbers in Consignee's Store.
Disconnection, Dismantling and Removal of Metre overhead bare conductor bunch (consisting with four / five / six conductors as per site), insulator & other all accessories from pole including transportation of released materials from site and handing over the same to Consignee's Store as per advice of the competent authority. Total 5903552.48
A-Work under SSEE/P/BLS.
B-Work under SSEE/P/MCA including HLZ & DGHA section.
C-Work under SSEE/P/GII.
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
Annexure-VA.pdf
ATTACHMENT
Declerationregardingretdrlyemployee.pdf
ATTACHMENT
BidSecurityAnnexure-VIA.pdf
ATTACHMENT
IndemnityBond.pdf
ATTACHMENT
FinancialEligibilityAnnexure-VIB.pdf
ATTACHMENT
CEE_G_A3_P-150_Alt.1-EarthingDrg.Spec..pdf
ATTACHMENT
Performancereportsheet.pdf
ATTACHMENT
GEN-Rep-OH-Line-BLS-MCA-GII.pdf
ATTACHMENT
PaymentConditionsLatest.pdf
ATTACHMENT
PoliceVerificationLetter.pdf
ATTACHMENT
Similar-Nature-Work-Consolidated-02-04-26.pdf
ATTACHMENT
NEFTMandateForm.pdf
ATTACHMENT
JPOfordiggnigwork.pdf
ATTACHMENT
Tendererform.pdf
ATTACHMENT
HQLTPanelSpec-16-06-25.pdf
ATTACHMENT
InstructionsregardingMakeApprovalofMaterials.pdf
ATTACHMENT
Download all tender documents and submit your bid