Renovation work at the Police Community Hall, Gorimedu, Puducherry

Amount

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size).

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacture's specification.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately) -Vengai wood.

Providing and fixing panelled or panelled and glazed shutters for doors, windows, and clerestory windows, including ISI marked M.S.pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete - Padak wood - 35 mm thick shutters.

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick - Padak wood.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part 1) decorative type, core of block board construction with frame of 1 st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters - 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

Extra for providing lipping with teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Providing and fixing plywood 4mm thick, one side decorative veneer conforming to IS: 1328 (type-1), for plain lining / cladding with necessary screws, including priming coat on unexposed surface with - Decorative veneer facings of approved manufacture.

Providing and fixing curtain rods of 1.25 mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with C.P.brass screws and wooden plugs, etc., wherever necessary complete - 25mm dia.

Providing 40 X 5 mm flat iron hold fast 40 cm long including fixing to frame with 10mm diameter bots, nuts and wooden plugs and embeddings in cement concrete block 30 x10 x 15 cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Providing and fixing ISI marked powder coating handles conforming to IS : 4992 with necessary screws etc.complete - 125 mm.

Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc.complete - 125 X 75 X 4 mm.

Providing and fixing aluminium sliding door bolts, ISI marked, anodised ( anodic coating not less than grade AC 10 as per IS: 1868), transparent or dyed to required colour or shade, with nuts and screws etc complete - 250 X 16 mm.

Providing and fixing aluminium tower bolts, ISI marked , anodised (anodic coating not less than grade AC 10 as per IS :1868), transparent or dyed to required colour or shade, with necessary screws etc. Complete - 250 x10 mm.

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS :1868), transparent or dyed to required colour or shade, with necessary screws etc. Complete - 200 x10 mm.

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc complete - Twin rubber stopper.

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50m in height dimension comprising of uPVC multi - chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 + or - 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook , zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I. fastners 100 x8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shyall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc.After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing.(Single / double glass panes, wire mesh and silicon sealent shall be paid separately) - Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels ) made of (bigl series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3+ or - 0.2 mm and single glazing bead / double glazinf bead of appropriate dimension.(Area of window above 1.75 sqm) - sliding window size 1.80x1.35 m.

Providing and fixing of 65 mm Godrej Navatal lock of 7 levers with 3 keys etc complete.

Steel work in built up tubular (round,square or rectanglar hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete - hot finished welded type tubes.

Providing and laying fully vitrified floor tiles of size 600 x600 mm (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622 of approved make (Nitco / Rak / Johnson /Asian ) in all colours and shades , laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete - size of tile 600 x600 mm.

Providing and fixing on wall face unplasticised rigid PVC rain water pipes conforming to IS: 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10mm gap for thermal expansion, (i) Single socketed pipes - 110 mm diameter.

Providing and fixing unplasticised - PVC pipe clips of approved design to unplasticised- PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length, including cutting brickwork and fixing in cement mortar 1:4 ( 1 cement : 4 coarse sand) and making good the wall etc., complete - 110mm.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.5mm (+0.05%) total coated thickness, zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both sides of the sheet and polyster top coat 15-18 microns using self drilling / self tapping screws complete - Flashings / Aprons (upto 600 mm).

20mm cement plaster of mix -1:4 (1 cement : 4 fine sand).

15mm cement plaster on rough side of single or half brick wall of mix - 1:4 (1 cement : 4 coarse sand).

Providing and applying ready mixed wall putty (JK / Birla) of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Applying one coat of water thinnable cement primer of approved brand and manufacturer on wall surface - water thinnable cement primer.

Finishing walls with acrylic smooth exterior paint of required shade - New work (two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg / 10 sqm).

Wall painting with plastic emulsion paint - Premium of approved brand and manufacture to give an even shade - two or more coats on new work.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade - Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacure.

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc complete.

Wall painting with plastic emulsion paint - Premium of approved brand and manufacture to give an even shade - One or more coats on old work.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade - One or more coats on old work.

Repair to plaster of thickness 12mm to 20mm in patches of area 2.5sqm and under including cutting the patch in proper shape, raking out joints and preparing plastering the wall surface with white cement based polymer modified self curing mortar, including disposal of rubbish, all complete.

Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead - in cement mortar.

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead - of area 3 sqm and below.

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead - for thickness of tiles 10mm to 25mm.

Dismantling cement asbestos or other hard board ceiling or partion walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Poilising the existing mosaic floor with Power polisher to a high degree of polish as to be perfectely smooth.

Acid cleaning for the existing Mosaic floors , glazed tiles work and removing the stains and decays to give a glassy look etc complet (The Acid used shall be 32% concentrated hydrochloric acid after taking on the precautionary measures).

Providing and fixing water closet squatting pan (Indian type W.C.pan) with 100 mm Sand Cast Iron P or S trap, 10 litre low level white P.V.C flusing cistren, including flush pipe, manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. Stainless steel AISI - 304 (18/8) Orissa pattern W.C.pan of size 585x480mm with flush pipe and integrated type foot rests.

Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps, 32mm C.P.brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required - white vitreous china anglet back wash basin size 600x480 mm with single 15mm C.P. brass pillar tap.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265mm sizes respectively.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P.brass screws and washers complete.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour - 600 mm long towel rail with total length of645 mm, 78 mm wide and effective height of 88mm, weighing not less than 190 gms.

Providing and fixing ASTM pipes including all ASTM plain & brass threaded fittings this included jointing of pipes & fittings with one step ASTM solvent cement, trenching refilling & testing of joints complete (External work) - 50 mm nominal outer dia pipes.

Providing and fixing unplasticised PVC connection pipe with brass unions - 45 cm length - 15mm nominal bore.

Providing and fixing C.P.brass bib cock of approved quality conforming to IS: 8931 - 15 mm nominal bore.

Providing and fixing C.P.brass stop cock (concealed ) of standard design and of approved make conforming to IS :8931 - 15 mm nominal bore.

Providing and fixing C.P.brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 8931- 15 mm nominal bore.

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality - LD - 2.5 - rectangular shape 600x450 mm inernal dimensions.

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I.cover with frame (light duty) 455 x 610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15kg), R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 (1 cement : 5 fine sand : 10graded stone aggregate 40mm nominal size ), inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete extra complete as per standard design - inside dimensions 600 x 850 mm and 45 cm deep for pipe line with three or more inlets - with common burnt clay F.P.S. (non modular) bricks of class designation 7.5.

Providing and fixing on wall / column face unplasticed - PVC soil and waste pipes (type - B) conforming to IS : 13592- 1992 including jointing with seal ring conformation to IS : 5382 leaving 10mm gap for thermal expansion - single socked pipes -110mm diametre.

Providing and fixing on wall face / column face unplasticised - PVC moulded fittings / accessories for unplasticisd - PVC soil and waste pipes conforming to IS:14735 - 1999 including jointing with seal ring conforming to IS :5382 leaving 10mm gap for thermal expansion - Single tee without door - 110 x110x110mm.

Providing and fixing on wall face / column face unplasticised - PVC mould fittings / accessories for unplasticisd - PVC soil and waste pipes conforming to IS : 14735 - 1999 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - bend 110 mm.

Providing and fixing on wall face / column face unplasticised - PVC mould fittings / accessories for unplasticisd - PVC soil and waste pipes conforming to IS : 14735 - 1999 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - heel rest bend 110 mm.

Providing and fixing on wall/column face unplasticised - PVC soil and waste pipes (type B) conforming to IS:13592 - 1992 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - single socketed pipes 75mm diameter

Providing and fixing on wall/column face unplasticisd - PVC moulded fittings /accessories for unplasticisd - PVC soil and waste pipes conforming to IS:14735 - 1999 including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion - Single tee with door -75x75x75mm

Providing and fixing on wall/column face unplasticisd - PVC moulded fittings /accessories for unplasticisd - PVC soil and waste pipes conforming to IS:14735 - 1999 including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion - Single tee without door -75x75x75mm

Providing and fixing on wall / column face unplasticised - PVC moulded fittings /accessories for unplasticisd - PVC soil and waste pipes conforming to IS:14735 - 1999 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - bend 75mm

Providing and fixing on wall / column face unplasticisd - PVC moulded fittings / accessories for unplasticisd - PVC soil and waste pipes conforming to IS :14735 -1999 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - heel rest Bend 75 mm.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS:733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e at top, bottom and sides with required EPDM rubber / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P.brass / stainless steel screws, all complete as per architectural drawings (Glazing, paneling and dash fasteners to be paid for separately) - for fixed portion - Powder coated aluminium (minimum thickness of powder coating 50 micron).

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS:733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e at top, bottom and sides with required EPDM rubber / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling , C.P.brass / stainless steel screws, all complete as per architectural drawings (Glazing, paneling and dash fasteners to be paid for separately) - for shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (fittings shall be paid for separately) - Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings ( cost of aluminium snap beading shall be paid in basic item) - with float glass panes of5.50 mm thickness.

Providing and fixing factory made single extruded WPC (Wood Polymer composite) solid door / window / Ceosetory windows and Other frames/ Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade) calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frames density of 750 kg / cum, screw withdrawal strength of 2200 N (Face) and 1100 N (Edge), minimum compresssive strength of 58N/sq.mm, modulus of elasticity 900 N/sq.mm and resistance to spread of flame of class A category with property of being termite / borer proof, water / moisture proof and fire retardant and fixed in position of with M.S hold fast/lugs /SS dash fasteners of required dia and length complete as per direction of Engineer-in-charge (M.S hold fast/lugs or SS dash fastners shall be paid for separately) Note: For WPC solid door / window frames, minus 5mm tolerance in dimensions i.e. depth and width of profile shall be acceptable. Variation in profile dimension on plus side shall be acceptable but no extra payments on this account shall be made. - Frame size 50 x 100 mm.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of required size comprising of virgin polymer K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawl strength of 1800 N (Face) and 900 N (Edge), minimum compressive strength 50N/sq.mm, modulus of elasticity 850 N/sq.mm and resistance to spread of flame of class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S.screws, all as per direction of Engineer-in-charge. (Note: Stainless steel butt hinges and necessary S.S.screws shall be paid separately) - 30mm thick.

Providing, laying and jointing UPVC pipes(Finolex / jain / Supreme / Truebore / Nandi) (0.6 Mpa)conforming to IS specification 4985 and ISI marked including transportation to the site, lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment,including cost of solvent cement,excluding UPVC specials such as bends,tees, threaded pieces,couplers,reducer,endcaps etc.,complete all as per IS and CPWD specification. - 160mm dia.

Providing and fixing in position UPVC fabricated coupler (Finolex / jain)(1 Mpa) conforming to IS 7834 part II and ISI marked, including labour charges for jointing, jointing materials etc, complete - 160 mm dia.

Providing and fixing of C.P brass health faucet of approved quality - 15mm nominal bore JAGUAR make as special type (Nos.573).

Providing two legged scaffolding on the exterior side, upto seven storey height using best quality of casurina posts of size 10 - 15 cm dia and the spacing of posts being 2 metre in both rows with two horizontal posts including longitudinal and transverse middle braces to set up and providing a platform with country wood planks of 40mm thick and to the required width etc., in a complete from using coir and rails with handrail for safety measures keeping the scaffolding till all the works are completed including the cost of all materials, lead and lift etc., complete as directed by the Engineer-in-charge. The elevational area of the scaffolding shall be measured for payment purpose. The payment will be made once irrespective of duration of scaffolding. (To be used for maintenance work judicically, necessary deduction for scaffolding in the existing item to be done.)

Providing and fixing of precoated galvanized iron profile sheets (size, shape and pitch of corrugation as 0.50mm (+0.05%), total coated thickness (TCT) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both sides of the sheet and polyster top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimm to avoid scratches whib transportation and should be supplied in single length upto 12 metre or as desired. The sheet shall be fixed using self drilling / self tapping screws of size (5.5 x 55mm) with EPDM seal (or with polymer coated J or I hooks) bolts and nuts 8mm diameter with bitumen and G.I limpet washer or with G.I limpet washers filled with white lead) complete upto any pitch in horizontal / vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. The rate includes all taxes.

SETSEAL A-A per packed water proofing two part system coating over the rough plastered surface after wetting the surface including all complete.

Providing a layer of trowel applied cementitious water proofing membrane of 5mm thick nominal SETSEAL TANKING-A pre packed water proofing single part system over the SETSEAL APPLIED primer surface after wetting the surface including all complete.

Providing and fixing PVC trap with PVC grating with or without vent arm complete including providing necessary lubricant and slip ring for fixing fittings, cost of cutting and making good the walls and floors- 110mm inlet and 110mm outlet.

Providing and fixing 125x125mm stainless steel grating for floor trap etc complete as directed by the Engineer-in-charge.

Providing and fixing 8mm thick prelaminated Bison Board flat pressed three layer or graded wood particle board conforming to IS:12823 grade-I type-II in paneling fixed in aluminium door, window shutters and partition frames with C.P brass/ stainless steel screws etc., complete as per architectural drawings perlaminated particle board with decorative lamination on one side and balancing lamination on other side all as directed by the Engineer-in-charge.

Sealing of cracks/porous concrete by Pressure grouting using cement slurry mixed with non shrink expanding grouting compound of CERA/ SIKA/ FOSROC/ Mc Bauchmie/ Don/ BASF or equivalent make certified & tested by accredited institutions. like IIT/SERC or so (Confirming to BS 8110 Part I), mixed in the ratio of 225g per 50Kgs bag of cement for injection grouting the RCC slab to strengthen the RCC Slab.

Providing and fixing 25mm dia ASTM Half turn valve of approved quality.

Providing and fixing C.P brass shower arm casted 190mm long light body for wall mounted shower with flange of Jaguar make Model No.SHA-477.

Providing and fixing C.P brass shower rose (Guru Make) with 15 or 20mm inlet 150 x 150mm square type of approved quality 15mm Nominal bore.

Removal of sludge from the septic tank and disposal of the same through the sewage tanker in safe location with an average lead of 10km. The rate to include the cost of labour charge for removing and relaying of cover slab laid over the septic tank mixing of Ferro Sulphate in to the septic tank for Through mechanical device and disposal of the same including hire charge for sewage tanker etc. complete as directed by the Engineer-in-charge.

Providing and laying architecturally designed false ceiling works using superior fire rated St.Gobain make gypsum board of 12.5mm thick mounted on GI frame work with ceiling section of size 80x26x0.55x3660mm spacing at 600mm c/c suspended from ceiling using hanger rods at 1200 c/c with screw to level and line and applying one coat of primer, two coats of putty followed by and reflective paint in front of the stage area to the pequired shape and size, including scaffolding etc., comlete as directed by the Engineer-in-charge upto 6.5m height.

Disposal of building rubbish and unserviceable dismantled materials upto 5 Km radius. The rate include incidental charge transportation by mechanical means loading and unloading etc., complete as directed by the Engineer-in-charge.

SIVAKUMAR K

S. SUDEESH

ASOKAN V