Construction of Faecal Sludge Treatment Plant -FSTP- of capacity 05 KLD at Dasarathpur, Rangat under CD-I, APWD, Rangat.

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lif.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:2:4 (1 cement : 2 coarse sand (zone-Ill) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

1:4:8 (1 Cement : 4 coarse sand (zone-Ill) derived from natural sources: 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Centering and shuttering including strutting, propping etc. and removal of form for

Foundations, footings, bases of columns, etc. for mass concrete

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access platform

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the following grades of concrete.: Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All works upto plinth level Concrete of M30 grade with minimum cement content of 350 kg /cum

All works above plinth level upto floor V level Concrete of M30 grade with minimum cement content of 350 kg /cum

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Electric resistance or induction butt welded tubes

Providing and fixing mild steel round holding down bolts with nuts and washer plates complete.

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.

40 mm thick with 20 mm nominal size stone aggregate

Providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with Zinc coating 120 gram per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :

Ridges plain (500- 600mm)

12 mm cement plaster of mix:

1:4(1 cement: 4 fine sand)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :

Two or more coats on new work

12 mm cement plaster finished with a floating coat of neat cement of mix:

1:4(1 cement: 4 fine sand)

Finishing walls with Acrylic Smooth exterior paint of required shade:

New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm)

Providing and laying 60 mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :

1:1.5:3(1 cement: 1.5 coarse sand (zone-Ill) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement:

1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Cement concrete pavement with 1:2:4(1 cement: 2 coarse sand :4 graded stone aggregate 20 mm nominal size), including finishing complete.

Providing and filling of filter media with 2 to 12mm stone aggregate laid for sludge drying bed etc all complete as per the direction of Engineer-in-charge.

Providing and laying hollow cement concrete block walling up to floor five level 200 mm thick consisting of hollow block of size 400 x 200 x 200 mm of 1:3:6 (1 cement : 3 coarse sand : 6 stone aggregate 12.5 mm nomial size) laid in cement mortor 1:6 (1 cement : 6 coarse sand).

Providing and fixing in position PVC pipe for weep hole in walls including cutting into size and placed at proper intervals by binding etc. all complete as per the direction of Engineer-in-chagre.

50 mm dia.

Providing and filling of material behind the wall for weep holes etc all complete as per the direction of Engineer-in-charge.

Stone aggregate of size 53 mm to 22.40 mm

Providing and fixing pre-painted galvalume (PPGL) steel profile sheets AZ-150 of brand Tata Bluescope steel, Everest Industries Ltd., JSW Steel Ltd., Jindal India Ltd. or equivalent (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50mm (+ 0.05%) total coated thickness with aluminium zinc coating 150 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping aluminium screws (Xylan) of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Sub Work: Complete assembly intergation testing and commisioning of Faecal Sewage Treatment Plant 5 KLD.

Feacal Sewage Treatment Plant- Supply, installation, testing and commissioning of Non clog Submersible Raw Sewage Tr. pumping set with CI body & impeller, connected to a motor suitable for 415 +/ 10% volts, 3 phase 50 cycles A.C supply as required and directed by Engineer-in-charge ( Make: Steron Pumps 3 Hp, 3 Phase or Equivalent) Raw Sewage Transfer Pump- Make: Kirloskar/Lubi or Equivalent (Pumps to be suitable to handle Solid handling capacity upto 28 mm size) WITH ALL FITTINGS No. of pumps : 02 Nos.(1 Working + 1 Standby) Capacity - 2.50 M3/Hr Head - 8.0-10 Mtr.

Supply, installation, testing & commissioning of Twin lobe rotary type Air blower & suitable motor of 415 ± 10% volts, 3 phase, 50 cycles A/C supply as required and directed by Engineer-in-charge No. of Blower : 02 no. (1 Working + 1 Standby) Make: blowvacc/KPT or Equivalent Capacity - As per OEM calculation Head - 3.0- 3.5 Mtr. pressur 0.3 ccm

Supply, installation, testing & commissioning of EPDM Tubuler type fine bubble diffusers having Length of 1000/600 mm and dia will be 63 mm with diffusion capacity 5-8 m3/hr for MBBR reactors .( Make: Scogen/EDI/OTT or Equivalent) as 1 Lot= 60 Pieces

Supply, installation, testing & commissioning of Lateral & Header type Coarse bubble diffussion system having diffusion capacity 3-5 m3/hr for equilisation tank, Anoxic tank & Sludge Holding tank .( Make: As per OEM) as 1 Lot= 60 Pieces

Supply, installation, testing & commissioning of Lateral & Header type sewage distribution grid for upflow Anaerobic bacteria, ecogiya. ( Make: As per OEM)

Supply, installation, testing and commissioning of floating /Fixed upflow Anaerobic filter media made of PVC/HDPE having surface area of 100-125 m2/m3 . ( Make: Guddi /Airfin or Equivalent) Type : Floating Ring/Fixed Fins : Internal Surface Arae : 100-125 m2/m3 Color : Black Treatment : UV sterlized MOC : HDPE

Supply, installation, testing and commissioning of high surface area floating MBBR media made of PVC/HDPE having surface area of 400 m2/m3 to be used in MBBR Reactor .( Make: Guddi /Airfin or Equivalent) Type : Floating Ring Fins : Internal Surface Arae : 400 m2/m3 Color : Black Treatment : UV sterlized MOC : HDPE

Supply, installation, testing and commissioning of OZONATER 5 gm as required and directed by Engineer-in-Charge ( Make: Guddi /Airfin or Equivalent)

Supply, installation, testing and commissioning of filter feed pump of horizontal centrifugal pumping set of suitable horsepower as required with CI body & impeller, shaft of Carbon steel and C.I. base & head with mechanical seal, connected to a TEFC induction motor suitable for 415 +/- 10% volts, 3 phase 50 cycles A.C supply including suction and delivery headers with G.I as required and directed by Engineer-in-Charge( Make: Kirloskar/Shakti 2 HP 3Phase Monobloc Pump KDI-225++ or Equivalent) Filter Feed Pumps- No. of pumps : 02 Nos.(1 Working + 1 Standby ) Capacity - 2.5 m3/hr Head - 25.0-30 Mtr.

Supplying, installation, testing & commissioning of MSEP/FRP vessel filter with frontal piping and Valves with all the required accessories. Filter shall include media, standard fittings like , sampling cock, rinse drain etc as required and directed by Engineer-in-Charge Mulitgrade Filter Capacity - 2.5 m3/hr Filtration rate - 12000 lph/sqm Filter dia approx. -400 mm Working pressure: 2.5 Kg/sq cm. Test pressure : 4. 5 Kg/sq cm

Hypo Dosing System - Supplying, Installation, testing and commissioning of floclation agent/settling agent dosing system comprising of Sintex Tank with inlet/ outlet connection, piping and valves along with metering pump & Tank for dosing. Flow rate (each) = 0-6 LPH Head = 3-4 mtr No. of Pumps: 02 Nos. ( 1 working + 1 Stand by ) Tank Capacity : 100 Ltrs

Supply, installation, testing & commissioning of MS FRP tanks , These tank should be fabricated from 4/5 mm thick for side wall & bottom respectively along with 1 mm FRP lining complete in all respects for making the system complete. lameela clarifier for 20 min. detetion time 01 no. MBBR Tank : 2 hours detetion time 02 Nos. lamella tyep Settler : 20 min. detetion time 01 no holding sump 2-3 cum

Supply, installation, testing & commissioning of all pipings (as described below) and isolation control valves including all necessary fittings and clamps, supports, hangers as required i/c cutting and making good the walls wherever required complete in all respects for making the system complete. ( Make: TATA/Jindal/su preme or Equivalent) uPVC : Submerged air piping MS Epoxy/uPVC : Air piping & pumped effluent riser (non-submerged)

Supplying, Installation, testing and commissioning of motor control centre fabricated out of 14 gauge CRCA sheet steel. Cable gland plates shall be provided on top as well as at the bottom of the panels. Panels shall be treated with all anticorrosive process before painting as per specifications with 2 coats of red oxide primer and final approved shade of powder coated paint. 2 Nos. earthing terminals shall be provided for 3 phase, 4 wire, 50 Hz supply system. Lifting hooks shall also be provided in case of large panels. Approval shall be taken for each panel before fabrication. Quoted rates shall be inclusive of cables (in accordance to specification) with earthing from panel to each motor/equipment and Instrumentation as required

Motor Control Centre Necessary cable alleys, internal/cabling, wiring, cabling from MCC to various pumps/equipment and interlocking, earthing for all equipment shall also included All motor & pumps shall be provided with Automatic level controller elctric panel for atuomation system with all respect

Supplying, installing and commissioning of Silent type ' Diesel generating set of 10 KVA with water cooled Diesel Engine, Electric start with suitable capacity 12 V battery, fitted complete with all the required accesories along with AC Alternator 3 Phase, 415 Volts, 50 Hz, 0.8 pf self Excited, Self Regulated Designed with Acoustic Enclosure(sound proof) as per CPCB-IV+, emission norms approved DG Set similar to KIRLOSKAR GREEN Make,Model:3R5

50NA 4GI or Equivalent.

Wiring for light point / Fan point / Exhaust Fan point / Call Bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed PVC conduit, with modular switch, modular plate, suitable size G.I. box and earthing the point with 1.5 sqmm.FRLS PVC insulated copper conducotor single core cable etc. as required .

Group-C

Wiring for Light/ power plug wiring with 2 x 4 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed PVC conduit alongwith 1 No. 4 sq.mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for Circuit/ sub main Wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed PVC conduit as required.

2x1.5 sq.mm + 1x1.5 sq.mm. earth wire

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 A & 15/16 A modular switch, connections etc. as required.

Installation, testing and commissioning of wall barcket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps per fitting, complete with all accessories including connections etc. as required.

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.

Supplying and Fixing of PVC Button / Angle Holder including connection etc as required.

Supplying and fixing following way, horizontal type Single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But withoutMCB/RCCB/Isolator)

6 -way , Double door.

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA 'C' curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single Pole

Supplying and fixing following rating , double pole , 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying of smart LED Bulb Similar to Havells LED ADORE 9w B22 CDL 2 STAR Lamp or Cromton/ Bajaj/ Havells/ Philips.

Supplying of 12W LED, 6000K ED Bulk head fittings similar to Luker, cat no. LBKOVSL 12 its equivalent.

Supply of 20W LED Retrofit Tube light Batten Make: Crompton, Model: DIJB12LT8-20 or its equivalent to IS specification.

Supply of 20W LED,6500K, 4 Feet, Retrofit Tube light similar to Philips, Model no. 20W865 T8 IND I 2100lm or its equivalent to IS specification.

Supplying of 5 star Energy saving ceiling fans BLDC (26W to 32W), 1200mm sweep (White), Make: USHA Model: Techno Air (Without remote) or equivalent.

Supplying of one number XLPE insulated PVC outer sheathed with galvanised round steel wire or steel srtip armoured aluminium conductor power cable of 1.1 KV grade of size 25 sq.mm x 3.5 core conforming to IS 7098 (Part-I) 1988 amended upto date.

Supplying and laying of DWC HDPE pipe of size 50/38, ISI marked along with all accessories like socket, bend, couplers etc . Conforming to IS 16205 (Part 24): 2018/IS, complete with fitting and cutting, jointing etc. on open surface as required.

50 mm dia (OD-50 mm & ID-38 mm nominal)

Laying of one number PVC insulated and PVC sheathed/ XLPE power cable of 1.1kV grade of following size in the existing HDPE/DWC pipe as required.

Upto 35 sq. mm

Laying of one number PVC insulated and PVC sheathed/ XLPE power cable of 1.1kV grade of following size in the existing HDPE/DWC pipe as required.

Laying of one number PVC insulated and PVC sheathed/ XLPE power cable of 1.1kV grade of following size in the existing open surface/duct as required.

Providing Earthing with safe earthing electrode of galvanization 80 to 100 microns length 2000 mm, 48mm dia and inner space to be filled with crystaline conuctive mixture including filling - up with electrodite (Back fill Compound) 50kg for safe earth electrode and provoding masonary enclosure with cover plate having locking attagement etc. as required. (Similar to ASHLOK make SEE brand safe earthing or equivalent)

Providing· and fixing 25 mm X 5 mm· G.l. strip in 40 mm dia G.l. pipe from earth electrode including connection with G.l. nut, bolt, spring, washer excavation and refilling etc. as required.

Supplying and laying of DWC pipe of size 40/32, ISI marked along with all accessories like socket, bend, couplers etc . Conforming to IS 16205 (Part 24): 2018/IS, complete with fitting and cutting, jointing etc.direct in ground (50 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required.

40 mm dia (OD-50 mm & ID-32 mm nominal)

Supplying and laying of DWC HDPE pipe of size 40/32, ISI marked along with all accessories like socket, bend, couplers etc . Conforming to IS 16205 (Part 24): 2018/IS, complete with fitting and cutting, jointing etc. on open surface as required.

40 mm dia (OD-40 mm & ID-32 mm nominal)

Supplying of one number XLPE insulated PVC outer sheathed with galvanised round steel wire or steel srtip armoured aluminium conductor power cable of 1.1 KV grade of size 6 sq.mm x 3 core conforming to IS 7098 (Part-I) 1988 amended upto date.

Fabricating and Supplying of metallic street light pole made out of an overall length of 6.5 meters long having a bottom section length of 5.00 meters with 65 mm dia 'B' class ISI marked G.I Pipe.Top section having a length of 1.5 meters with 40 mm dia 'B' class ISI marked G.I Pipe suitably bended for installing 01 No Street Light having earth stud and necessary GI reducer/coupling fixed at the top & middle. Welding 300 mm x 300mm x 6mm thick MS base plate to the bottom including welding 100 mm X 25mm X 5mm M.S Flat for fixing PVC junction Box with 6A MCB on the Pole, i/c one coat of metalic primer and 02 coat of silver paint.Providing necessary wiring between junction box and st light fitting by 2x 1.5 Sq mm FR-LSH PVC Insulated copper conductor cable etc. as required.

Erection of pole of following length in brick ballast and ramming the foundation, finishing with 150mm thick cement concrete (1 :3:6) layer on top with including excavation and refilling etc. as required.

Above 4.5 meter and upto 6.5 meter

Supplying and Fixing LED street light of 30W with IP66 protection and impact resistance