Supply, Delivery, installation, testing, commissioning with 3 month trial run 5 years operation and maintenance of Pumping Machineries Raw water pumping -6 no of pumps each of (1250 cum/hr.) 415V MCC at pump house, power distribution of th

Amount

PUMPING MACHINARY (LT 415 Volts Design,Manufacture, supply, Installing, testing & commissoning of Vetical Turbine Pumps with suitable rpm for following duty points. a) Duty point discharge 1250 cum/hr.(each pump) b) Duty point head(28m) suitable to provide combined discharge at rated head as mentioned and pump efficiency shall be not less than 75%. c) These pumps should be suitable for parallel operation to deliver the required combined flow of 5000cum/hr for 20 Hrs in a day, continuous operation by running 4 pumps with 2 standby pump at Combined Duty point head 28m, 0.415 KV 3 Phase 50 Hz Vertical squirrel cage induction motor ,Design ,Manufacture ,supply, erection ,testing and commissioning of 0.415 kv 3 Phase 50 Hz Vertical squirrel cage induction motor suitable to the above pump. The motor shall be conforming toIP55 Class of protection TEFC,CACA,TEWC type of enclosure Class F insulation with a temperature rise limited to ClassB and as per the standard specifications. d) Specific gravity of Raw water 1.05.

Supply, Delivery, Installation, Testing & commissioning of 10 Ton EOT/HOT crane for Raw water pump house. C/C Span is 15 m and movable length is 25.5 m and Hoist lift is 10 m

Supply, Delivery, Installation, Testing & commissioning of LT MCC Panel Board and capacitor bank for all LT motors of Raw water Pump house as per SLD

Supply, Delivery, Installation, Testing & commissioning of FCMA Soft Starter Panel for 415 V LT Motors of Raw water pumps

LT 1.1 KV grade XLPE Cable from MCC panel to corresponding motor/stater etc. within the pump house.

Supply, Delivery, Installation, Testing & commissioning of Ventilation Fans for Pump House

Supply, Delivery, Installation, Testing & commissioning of Local control panel and push button stations.

Supply, Delivery, Installation, Testing & commissioning of different earthing systems of equipments (Other than Sub station),cable trays,lighting arrester etc.

Supply, Delivery, Installation, Testing & commissioning of indoor & outdoor lighting and small power distribution system

Internal illumination of Pump House with complete wiring

Supply, Delivery, Installation, Testing & commissioning of Instrumentation work & other ancilliary works

Supply, Delivery, Installation, Testing & commissioning of different MS/DI specials,joints, valves (Motorized BF, non return valve, Dismantling joints) 500 mm Dismantling Joint: Manufacture, Supply And Delivery Of M.S. Dismantling Joints With Gl Studs Of 500Mm Size With Both Side Flange End Suitable For Installation In Between Flanged End Pipes. Pressure Rating Pn-10 And Drilling Standards Shall Be As Per Is:1538.

Supply, Delivery, Installation, Testing & commissioning of different MS/DI specials,joints, valves (Motorized BF, non return valve, Dismantling joints) 500 mm PN 1.0 DI D/F Swing Check type reflux non return valve Of Below Mentioned Pn Ratings , Dia / Sizes Confirming To The Body And Door Shall Be Of Closed Grained Cast Iron Is:210 Gr 20; Body Seat Shall Be Of Stainless Steel Ss 304, Disc Seat Shall Of Natural Rubber And The Trunnion Shaft Shall Be Of Stainless Steel AISI 410,As Per Is:5312 (Part 1) With Drilling And Thickness As Per Is: 1538.

Supply, Delivery, Installation, Testing & commissioning of different MS/DI specials,joints, valves (Motorized BF, non return valve, Dismantling joints) 500 mm PN-10 ,ELECTRICALLY OPERATED D.I.DF BUTTERFLY VALVE : Butterfly valves shall be of wafer type double flanged and short body type conforming to IS: 13095; The drive shaft and end shaft shall be of stainless steel IS: 6603 Gr 12 Cr 12 or Stainless steel BS 970 Grade 413 S19 ; Face to face dimensions as per As per IS:13095 or BS:5155, Disc seal ring - EPDM,Disc seal retaining ring - Stainless steel ASTM 351-CF8M, Body seat - Stainless steel AISI 316/ nickel weld overlay micro finished/ integral micro finished seat with valve body. Drilled as per lS 1538. Acuators shall be with integral stafters and shall have position transmitters.

Supply, Delivery, Installation, Testing & commissioning of different station pipes, specials and misc. materials A) Manufacturing of MS pipes shall be done in conformity with IS: 3589, 500 MM (OD) With 6.3 MM ThicknessMs-Pipe B) Manufacturing of MS pipes shall be done in conformity with IS: 3589, 1000 MM (OD) With 11.00 MM ThicknessMs-Pipe

Supplying, installation of Valves (Air valves/Sluice/Butterfly/Washout /Pressue Reducing etc.), Electro-magnetic flowmeter on Raw water Pumping Main from Intake Pump House and upto WTP all complete. 1000MM, PN-10 ,ELECTRICALLY OPERATED D.I.DF BUTTERFLY VALVE : Butterfly valves shall be of wafer type double flanged and short body type conforming to IS: 13095; The drive shaft and end shaft shall be of stainless steel IS: 6603 Gr 12 Cr 12 or Stainless steel BS 970 Grade 413 S19 ; Face to face dimensions as per As per IS:13095 or BS:5155, Disc seal ring - EPDM,Disc seal retaining ring - Stainless steel ASTM 351-CF8M, Body seat - Stainless steel AISI 316/ nickel weld overlay micro finished/ integral micro finished seat with valve body. Drilled as per lS 1538. Acuators shall be with integral stafters and shall have position transmitters.

Supplying, installation of Valves (Air valves/Sluice/Butterfly/Washout /Pressue Reducing etc.), Electro-magnetic flowmeter on Raw water Pumping Main from Intake Pump House and upto WTP all complete. 1000Mmϕ Electro Magnetic Flow Meter On Rising Mains With Range-5000 M3/Hr ,Type-Electromagnetic Flow Meter Accuracy-+/- 0.5% Of Full Scale Or Better All Required Mounting Accesaries,O/P-4-20Mamp Sensors & Transmitter Shall Be Seprated Pressure Rating -Pn 1.0,Scada Compartble..

ADD GST 18%

integrated engineering (BID ID -6544462)

Bhugan Infracon Pvt. Ltd. (BID ID -6552535)

Sri Padmavathi Engineering Works (BID ID -6551140)