Civil, Electrical, Data and Telephone works for placing the 40 feet container for Drone Assembly Integration Testing Facility at NIOT Campus, Chennai

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.Note i)M-Sand Maybe used

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) Note i)M-Sand Maybe used ii) RMC concrete should be used

Centering and shuttering including strutting, propping etc. and removal of form work for : Foundations, footings, bases of columns, etc. for mass concrete all complete as per instruction of Engineer In - Charge.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.All works upto plinth level. Concrete of M25 grade with minimum cement content of 330 kg /cum Note i)M-Sand Maybe used ii) RMC concrete should be used iii) concrete must cube test 7th day , 28th day for compressive strength of concrete to submit orginal test report. iv) M-25 Design mix should be submitted

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. Make: TATA / Isteel /Vizag/Sail

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. Note: For Hook (30 Nos) Make: TATA / Isteel /Vizag/Sail

Wall painting with External wall primer paint of approved brand and manufacture to give an shade: one or more coats on new work. Note Apex Dust Proof Exterior Emulsion appropriate priming coat/ Trucare Exterior Wall Primer or equivalent

Wall painting with exterior emulsion paint of approved brand and manufacture to give an even shade :Two or more coats on new work Note: Apex Dust Proof Exterior Emulsion or equivalent

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:6 (1 cement : 6 coarse sand Note i)M-Sand Maybe used

Half brick masonry with common burnt clay F.P.S (non modular) bricks of class designation 7.5 in foundations and plinth in. Cement mortar 1:3 (1 cement: 3 coarse sand(m-sand)) Note i)M-Sand Maybe used

15mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement:6 fine sand) Note i)M-Sand Maybe used

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 100 metres lead as per direction of Engineer-in-charge. In cement mortar

Supply and laying of 4C x 16sqmm XLPE insulated Copper armoured 1.1kV graded UG cable with suitable clamb and all accessories along the Cable trench/Container wall as required as per site condition. Location: Solar Panel room PDB Panel to Drone Assembly Integration facility Container. Make: Polycab/RR kabel/KEI/SN cab/Gloster

Supply and Making of end termination with single compression gland (4C x 16sqmm) suitable crimping lugs.The gland should be double earthed by suitable copper wire and earth strip. Location: * Solar Panel room PDB Panel - 1no. * Container New VTPN - 1no. Make: Comet / Comex

Supply and laying of 2C x 6sqmm XLPE insulated Copper armoured 1.1kV graded UG cable with suitable clamb and all accessories along the Cable trench/Container wall as required as per site condition. Location: Solar Panel room PDB Panel to Drone Assembly Integration facility Container.(For EARTH) Make: Polycab/RR kabel/KEI/SN cab/Gloster

Supply and Making of end termination with single compression gland (2C x 6sqmm) suitable crimping lugs.The gland should be double earthed by suitable copper wire and earth strip. Location: * Solar Panel room PDB Panel - 1no. * Container New VTPN - 1no. Make: Comet / Comex

Supply,fixing and termination of 4way Three phase double door protection MCB VTPN DB along the Container wall and fixing of following rating MCB's along the VTPN DB. The job including of minor welding work and MS materials. A) C63A FP MCB - 1nos.(VTPN Incomer) B) C20A SP MCB - 5nos.(For A/C) C) MCB Dummy - 7nos. Make : Legrand/Hager

Supply and laying of 4C x 6sqmm XLPE insulated Copper armoured 1.1kV graded UG cable with suitable clamb and all accessories along the Cable trench/Container wall as required as per site condition. Location: Solar Panel room LDB VTPN to Drone Assembly Integration facility Container.(For Lighting) Make: Polycab/RR kabel/KEI/SN cab/Gloster

Supply and Making of end termination with single compression gland (4C x 6sqmm) suitable crimping lugs.The gland should be double earthed by suitable copper wire and earth strip. Location: Container Lighting DB - 1no. Make: Comet / Comex

Supply, fixing and termination of 12way Single phase double door protection MCB DB along the Container wall and fixing of following rating MCB's along the SP DB. The job including of minor welding work and MS materials. A) C40A DP MCB - 1nos. B) C16A SP MCB - 5nos. C) C10A SP MCB - 5nos. Make : Legrand/Hager

Laying and termination of existing 20pair copper jelly filled Telephone armoured UG cable along the wall/Cable trench.The job including of suitable clamps with all accessories as required as per site condition. Location: Solar Panel Room.

Supply, fixing, wiring and termination of 4 module telephone Krone block (4nos 10pair IDC Module) with suitable Aluminium telephone krone frame,suitable surface powder coated box along the wall and complete fixing accessories. Location : Solar Panel room & Container. Make: Amp/Krone/Molex

Supply of Caller Id 16 digit single LCD display,30 incomer and 5 outgoing memory,real time clock with year,date and month display land line Telephone instrument. Colour : Black. Model : C51, Make : Beetel

Supply and laying of Cat6 4pair UTP data shielded Armoured cable along the wall/Cable trench/excavation area required as per site condition with termination of the cable to the RJ45 data end jack's.The job includes of minor excavation work. Location: * Solar Panel Room Krone box to Container Krone Box- 120Mtrs. * Second gate security cabin data switch to cantainer data rack - 120Mtrs. Make : Molex/Krone/Amp

Supply, installation, testing and commissioning of IP65 weather proof 30watts flood light along the container outside wall with Suitable clamp.the job including of Minor welding works with MS materials.one year Product replacement warranty. Make : wipro / Crompton / Luker

Supply and fixing of IP65 weather proof 6way Thermo plastic box with 4nos of C6A SP MCB & 2nos of MCB Dummy, Box alone the Container wall.the job including of Minor welding works with MS materials.(Control for flood light's) Location : Drone Container Make:Legrand/Hager/Hensel/Sintex

Supply, Installation, testing, commissioning and programming of 24Port Analog Subscriber Card (SLMAV24) with 24 Pair MDF Cable Suitable for existing Hi Path 4000 EPABX system. Make : Unify ( Specific brand )

TOTAL WITHOUT GST

jayaa enterprises (BID ID -3218664)

WINTECH ENGINEERING SERVICES (BID ID -3218400)

JPS CONSTRUCTIONS (BID ID -3222619)

Udaya Technologies Private Limited (BID ID -3222671)

Janta Engineers and Company (BID ID -3218300)