REPAIR AND MAINT OF PUMPS MOTOR STARTERS DOZER CHLORINATION PLANT CLEANING OF SUMP/OH TANK AND OTHER CONNECTED WORKS AT DHAR ROAD AND SAMNABANJ UNDER GE (ARMY) DHAR ROAD

Amount

Taking out with proper shut down by disconnecting all the electrical connections, dismantling the unserviceable 100 HP 3 phase induction motor and disconnected with Vertical turbine pump set , four stage (BHR 28-18) (installed at Jackwell) from the base plate,column pipe and shifting the same to approved workshop for repair/rewinding. Dismantling the motor, rotor ,shaft, slip rings,carbon brush assembly etc carefully. cutting and removing the old heated up/burnt winding of the stater /rotor, cleaning the slots and replacement of brunt spare parts and reassembling the motor including transportation back the same after rewinding and reassembling, all as specified and directed by Engr -in- Charge. Note:- (a) cost of rewinding will be measured and paid separately. (b) Motor shall be dismantled at workshop and its winding cut shall be made in presence of authorised MES rep. (c) Major Spare parts such as bearing, shaft will be measured and paid separately. (d) The contractor shall reinstall/make the UNSV motor serviceable within one week after loadging of complaint either by handing over the written complaint/ any means of tele messaging services , failing which a penelity @ Rs. 5000/- per day of delay will be charged from the contractor. (e) The rates quoted shall be deemed to include the cost of loading/unloading, transportation, grease, nuts, bolts,pins, rubber gaskit, washers insulating materials i.e varnish, cotton tape insulating paper and soldering of any size and shape duly functional and testing at its original location/position complete. (f) After repair of motor One Year guarantee will be borned by the Contractor.

Taking out with proper shut down by disconnecting all the electrical connections, dismantling the unserviceable Vertical terbine pump set , four stage (BHR 28-18) 100 HP (installed at Jackwell) from the base plate,column pipe and shifting the same to approved workshop for repair of pump set. Dismantling the pump parts such as key, coupling,bush, gland, ring, shaft sleeve,impleer, bearing, nut,bolt,washers,rubber gaskit etc any type and size from the pump carefully. Replacement of UNSV spare parts and reassembling the Pump set complete as before including transportation and fixing it back after repairing and duly tested all as specified and directed. Note:- (a) Pump shall be dismantled at workshop in presence of authorised MES rep. (b) The rate of materials includes the labour for fixing of any type Spare parts will be measured and paid separately. (b) The rates quoted shall be deemed to be included the cost of loading/unloading, transportation, grease, nuts, bolts,pins, rubber gaskit and washers etc of any size and shape duly. (c) Major Spare parts will be measured and paid separately. (d) the rate includes refixing the pumps in its original positioin, testing complete all as directed.. (e) The contractor shall reinstall/make the UNSV Pump set serviceable within one week after loadging of complaint either by handing over the written complaint/ any means of tele messaging services , failing which a penelity @ Rs. 5000/- per day of delay will be charged from the contractor. (f) After repair of the pump set One Year guarantee will be borned by the Contractor.

Taking out with proper shut down by disconnecting all the electrical connections, dismantling the unserviceable 3 Ph induction motor 55/75 KW/HP, DSM 125/40 (installed at Fresh water sump) from the base plate and shifting the same to approved workshop for repair/rewinding. Dismantling the motor, rotor ,shaft, slip rings,carbon brush assembly etc carefully. cutting and removing the old heated up/burnt winding of the stater /rotor, cleaning the slots and replacement of brunt spare parts and reassembling the motor including transportation back the same after rewinding and reassembling, all as specified and directed by Engr -in- Charge. Note:- (a) cost of rewinding will be measured and paid separately. (b) Motor shall be dismantled at workshop and its winding cut shall be made in presence of authorised MES rep. (c) Labour for fixing of any type Spare parts will be measured and paid separately. (e) Major Spare parts such as bearing, shaft will be measured and paid separately. (f) The contractor shall reinstall/make the UNSV motor serviceable within one week after loadging of complaint either by handing over the written complaint/ any means of tele messaging services , failing which a penelity @ Rs. 5000/- per day of delay will be charged from the contractor. (g) The rates quoted shall be deemed to include the cost of loading/unloading, transportation, grease, nuts, bolts,pins, rubber gaskit,washers ,insulating materials i.e varnish, cotton tape insulating paper and soldering of any size and shape duly functional and testing at its original location/position complete. (h) After repair of motor One Year guarantee will be borned by the Contractor.

Taking out with proper shut down by disconnecting all the electrical connections, dismantling the unserviceable Pump set DSM 125/40, 55/75KW/HP alongwith (installed at Fresh water sump) from the base plate and shifting the same to approved workshop for repair of pump set. Dismantling the pump parts such as key, coupling,bush, gland, ring, shaft sleeve,impleer, bearing, nut,bolt,washers,rubber gaskit etc any type and size from the pump carefully. Replacement of UNSV spare parts and reassembling the Pump set complete as before including transportation and fixing it back after repairing and duly tested all as specified and directed. Note:- (a) Pump shall be dismantled at workshop in presence of authorised MES rep. (b) The rate includes the labour for fixing of any type Spare parts will be measured and paid separately. (b) The rates quoted shall be deemed to be included the cost of loading/unloading, transportation, grease, nuts, bolts,pins, rubber gaskit and washers etc of any size and shape duly. (c) Major Spare parts will be measured and paid separately. (d) the rate includes refixing the pumps in its original positioin, testing complete all as directed.. (e) The contractor shall reinstall/make the UNSV Pump set serviceable within one week after loadging of complaint either by handing over the written complaint/ any means of tele messaging services , failing which a penelity @ Rs. 5000/- per day of delay will be charged from the contractor. (f) After repair of the pump set One Year guarantee will be borned by the Contractor.

Taking out with proper shut down by disconnecting all the electrical connections, dismantling the unserviceable multi stage Kirloskar make pump set 20 HP, Speed 2930 rpm, pump head 300 Mtrs, discharge 7.20 cubic meter/hour, pump inupt 11.32 KW installed at Samana Banj location from the base plate and shifting the same to approved workshop for repair of pump set. Dismantling the pump parts such as key, coupling,bush, gland, ring, shaft sleeve,impleer, bearing, nut,bolt,washers,rubber gaskit etc any type and size from the pump carefully. Replacement of UNSV spare parts and reassembling the Pump set complete as before including transportation and fixing it back after repairing and duly tested all as specified and directed. Note:- (a) Pump shall be dismantled at workshop in presence of authorised MES rep. (b) The rate includes the labour for fixing of any type Spare parts will be measured and paid separately . (b) The rates quoted shall be deemed to be included the cost of loading/unloading, transportation from Samanabanj station under GE (A) Dhar Raod, grease, nuts, bolts,pins, rubber gaskit and washers etc of any size and shape duly. (c) Major Spare parts will be measured and paid separately. (d) the rate includes refixing the pumps in its original positioin, testing complete all as directed.. (e) The contractor shall reinstall/make the UNSV Pump set serviceable within one week after loadging of complaint either by handing over the written complaint/ any means of tele messaging services , failing which a penelity @ Rs. 5000/- per day of delay will be charged from the contractor.

Taking out with proper shut down by disconnecting all the electrical connections, dismantling the unserviceable 3 Ph induction motor 15 KW/20 HP make Kirloskar, having RPM 2940, From Samana Banj Station under GE (A) Dhar Road from the base plate and shifting the same to approved workshop for repair/rewinding. Dismantling the motor, rotor ,shaft, slip rings,carbon brush assembly etc carefully. cutting and removing the old heated up/burnt winding of the stater /rotor, cleaning the slots and replacement of brunt spare parts and reassembling the motor including transportation back the same after rewinding and reassembling, all as specified and directed by Engr -in- Charge. Note:- (a) cost of rewinding will be measured and paid separately. (b) Motor shall be dismantled at workshop and its winding cut shall be made in presence of authorised MES rep. (c) Labour for fixing of any type Spare parts will be measured and paid separately. (e) Major Spare parts such as bearing, shaft, winding required for the repair will be measured and paid separately. (f) The contractor shall reinstall/make the UNSV motor serviceable within one week after loadging of complaint either by handing over the written complaint/ any means of tele messaging services , failing which a penelity @ Rs. 5000/- per day of delay will be charged from the contractor. (g) The rates quoted shall be deemed to include the cost of loading/unloading, transportation from Samanabanj station under GE (A) Dhar Raod, grease, nuts, bolts,pins, rubber gaskit,washers ,insulating materials i.e varnish, cotton tape insulating paper and soldering of any size and shape duly functional and testing at its original location/position complete.

Taking out with proper shut down by disconnecting all the electrical connections, dismantling the unserviceable Diesel engine driven Kirloskar make having prime mover rating 32 WHP, 1500 RPM alongwith speed increasing gear box, pump head 280 Mtrs, discharge 7.20 cubic meter/hour, installed at Samana Banj location from the base plate and shifting the same to approved workshop for repair of pump set. Dismantling the pump parts such as key, coupling,bush, gland, ring, shaft sleeve,impleer, bearing, nut,bolt,washers,rubber gaskit etc any type and size from the pump carefully. Replacement of UNSV spare parts and reassembling the Pump set complete as before including transportation and fixing it back after repairing and duly tested all as specified and directed by Engr -in- Charge. Note:- (a) Pump shall be dismantled at workshop in presence of authorised MES rep. (b) The rate includes the labour for fixing of any type Spare parts will be measured and paid separately. (b) The rates quoted shall be deemed to be included the cost of loading/unloading, transportation from Samanabanj station under GE (A) Dhar Raod, grease, nuts, bolts,pins, rubber gaskit and washers etc of any size and shape duly. (c) Major Spare parts will be measured and paid separately. (d) the rate includes refixing the pumps in its original positioin, testing complete all as directed.. (e) The contractor shall reinstall/make the UNSV Pump set serviceable within one week after loadging of complaint either by handing over the written complaint/ any means of tele messaging services , failing which a penelity @ Rs. 5000/- per day of delay will be charged from the contractor.

M&L for cleaning of over head tank /under ground sump by scraping/removing all funges, scales, dust, sludge etc from inside of the over head tank and depositing the same to a distance exc 50 mtrs and n.exc. 100 mtrs including washing the walls & bottom of the over head tank with water and disinfection chemical such as bleaching powder etc and writing date of cleaning, Capacity of tank, CA No with synthetic enamel black/white paint complete for 150000 gallons capacity complete all as specified and directed. (Near Filter plant)

All as per item No 08.00 above but of capacity 75000 Gallon (MRS &Bde)

All as per item No 08.00 above but of capacity 50000 Gallon (Bde and MRS)

All as per item No 08.00 above but of capacity 25000 Gallon (Kamlesh vihar)

M&L for opening the body of monoblock pump/centrifugal pump taking out impeller, bush, bearing shaft, stuffing box, reassembling the same after replacing the defective parts & carrying out the necessary repair, cleaning the slot, remetalling, turning, polishing the pump shaft, replacement of steel studs and unserviceable nuts & bolt, repair / replacement of ball bearing, impellor, stuffing box, greasing, varnishing, etc. and testing on completion and commissioning complete all as specified and as directed for the following capacities of pump sets:

(a) for 10 HP to 15HP

(b) for 5 to 7.5 HP

(c) for 2 to 5HP sludge pump/monoblock pump/induction pump

Taking down unserv motor and Rewinding the motor rotor with super enamelled copper winding wire/strip as per existing size and truns etc including all the insulating materials i.e varnish, cotton tape insulating paper and soldering,grease, nuts, bolts,pins, rubber gaskit,washers etc of any size are incl for the motor capacity 10 to 15 HP complete all as specified and directed by Engr-in-Charge.Note:- (a) Winding cut shall be made in presence of MES Rep and reassembling shall be done after inspection by MES Rep. (b) Rewinding wire of motor will be measured and paid separately under relevent item. (c) The motor shall be squerrel cage induction/slipring induction motor.

Taking down unserv motor and Rewinding the motor rotor with super enamelled copper winding wire/strip as per existing size and truns etc including all the insulating materials i.e varnish, cotton tape insulating paper and soldering,grease, nuts, bolts,pins, rubber gaskit,washers etc of any size are incl for the motor capacity 5 to 7.5 HP complete all as specified and directed by Engr-in-Charge.Note:- (a) Winding cut shall be made in presence of MES Rep and reassembling shall be done after inspection by MES Rep. (b) Rewinding wire of motor will be measured and paid separately under relevent item. (c) The motor shall be squerrel cage induction/slipring induction motor.

Taking down air comperssor set with motor and Rewinding the motor rotor with super enamelled copper winding wire/strip as per existing size and truns etc including all the insulating materials i.e varnish, cotton tape insulating paper and soldering, grease, nuts, bolts,pins, rubber gaskit,washers etc of any size are incl for motor capacity 30 HP complete all as specified and directed by Engr-in-Charge.Note:- (a) Winding cut shall be made in presence of rep of EIC and reassembling shall be done after inspection by Ref of EIC. (b) Rewinding wire of motor will be measured and paid separately under relevent item. (c) The motor shall be squerrel cage induction/slipring induction motor.

Taking out unserviceable motor shifting to workshop and dismantalling, cutting of burnt windings and rewinding with supper enameled copper winding wire as per existing size and truns etc including all the insulating materials ie. varnish, cotton,tape, insulating paper and soldering, grease, nuts, bolts,pins, rubber gaskit,washers etc of capacity below 5 HP, 3 phase 415 volts, incl. reassembling, reinstalling at original location or including testing complete all as specified and directed. Note:- (a) Winding cut shall be made in presence of Rep of EIC and reassembling shall be done after inspection by the Rep of EIC. (b) Rewinding wire of motor will be measured and paid separately under relevent item. (c) The motor shall be squerrel cage induction/slipring induction motor.

Rewinding the motor stater with super enamelled copper winding wire of existing size and gauge and truns etc including all the insulating materials i.e varnish with suppr high quality of cotton tape, insulating paper and other misc items of motor any capacity (vertical terbine/ centrifugal/induction) all as specified and directed

Supply & Fixing in replacement of 100 HP Motor bearing DE/NDE 6318-C3 or as per existing make and type complete all as specified and directed.

Supply & Fixing in replacement of 75 HP Motor bearing DE6314 C3 or as per existing make and type complete all as specified and directed.

Supply & Fixing in replacement of 75 HP Motor bearing NED 6311 C3 or as per existing make and type complete all as specified and directed.

Supply & Fixing in replacement of compressor Motor bearing DE/NED 6311 2Z or as per existing make and type complete all as specified and directed.

Supply & Fixing in replacement of Alum/bleaching Motor bearing DE/NED 6203 2Z or as per existing make and type complete all as specified and directed.

M&L for taking out old unserviceable existing chlorination dozing spare parts from dozing plant and repair/replacement of the unserviceable spare parts as per existing type and size like NRV, suction/delivery pipes of existing length and type/size with fixing arrangement, motor required, filter for making dozing system functional and testing and commissioing including disposing off all unserviceable taken out parts / components complete all as specified and as directed

Supply of Cooling fan blade for Induction motor of capacity 50 to 100 HP same as per the present type and size all as directed.

Disconnecting the Blower of 1200 RPM, 8.5 CFM, 30 HP and type and make carefully dismantling it with commected motor complete for servicing by cleaning the bearing/bush by cleaining solution and replacing the unserviceable items like bearing, Nut Bolt& washer,Greasing of bearing etc., assembling Blower and refixing in the original place connection and testing complete all well as specified and as directed.

Supply and fix as in repair Non Return Valve of 125 MM, PN 1 NRV along with nut, bolt, washer and rubber gas kit , including taking down of old UNSV one complete all as spd and directed.

Supply and fix as in repair Non Return Valve of 150 MM, PN 1 NRV along with nut, bolt, washer and rubber gas kit , including taking down of old UNSV one complete all as spd and directed.

Supply and fix as in repair Non Return Valve of 200 MM, PN 1 NRV along with nut, bolt, washer and rubber gas kit , including taking down of old UNSV one complete all as spd and directed.

Supply and fix as in repair Non Return Valve of 300 MM, PN 1 NRV along with nut, bolt, washer and rubber gas kit , including taking down of old UNSV one complete all as spd and directed.

Removing the valve with the help of crane/triport, repairing and refixing NRV 300 mm by replacing its old rubber/leather with new sheet as per present shape, size and type, gaskit, nut ,bolt, washer,breazing,welding,lathe work etc required to repair valve complete.

Taking out sludge/foreign material//silt/vegetation/mud from filter bed tank at tawi filter plant (into two parts) including taking down old muddy unserviceable media filter and provide new filter media ie gravels,sand media etc as required and dewatering the residual water and cleanings the walls with the help of blade/scrapper/wire brush, preparation of old surface and applying one coat of lime wash including removing the sludge/silt/foreign material complete and depositing where directed out side the defence area complete all as specified and directed.

Taking out sludge/foreign material/silt/vegetation/mud from the square clear water UG sumps capacity 12 Lakh gallons (in two part) dewatering the residual water and cleaning the wall with help of blade/scrapper/wire brush, preparation of old surface and applying one coat of lime wash including removing the sludge/silt/foreign material complete and depositing where directed out side defence land complete all as specified and directed.

Taking out sludge/foreign material//silt/vegetation/mud from the clarifloculator tanks circular type capacity 1.5 Lakh gallon and cleaning the walls with wire brush/blade/ scrapper, preparation of old surface and applying one coat of lime wash including removing the sludge/silt/foreign material complete and depositing where directed out side defence land as and when required basis complete all as specified and directed.

Taking out sludge/foreign material/silt/vegetation/mud from the pre-sedimentation tank of capacity 1.5 lakh gallon and cleaning the wall tile with cleaning agent including removing the sludge/silt/foreign material and depositing where directed out side defence land as and when required basis complete all as specified and directed.

Taking out sludge/foreign material/silt/vegetation/mud from the back wash chamber and Jack well by cleaning the wall tiles with cleaning agent including removing silt/sludge and depositing where directed out side defence land as and when required basis complete all as specified and directed by Engineer-in-Charge. Note: The works to be carried out in parts as at least one supply of water is to be restored per day and the contractor will arrange all type of T&P such as suction pump, wire brush, castic soda, tools & plants for destroy/dispose of mud and sludge etc. Hence tenderes are required to quote their rates accordingly after site visit.

M&L as in repair of manhole covers / valve pit covers fabricated out of MS sheet, MS flat and angle iron of required sizes or shapes required at site and painting with one coat of black synthetic enamel paint over a coat of red oxide primer including taking out / dismantling rusted or unserviceable covers of UG sump/OHT/valve pits, etc. and disposing off complete all as specified

S&F in replacement of double flanged sluice valve of size 400 mm bore class PN 1 with stainless steel spindle including replacement of worn out rubber sheet nut, bolts and washers, including taking down of old and UNSV valve complete all as specified and directed

S&F in replacement of double flanged sluice valve of size 300 mm bore class PN 1.6 with stainless steel spindle including replacement of worn out rubber sheet nut, bolts and washers, including taking down of old and UNSV valve complete all as specified and directed

S&F in replacement of double flanged sluice valve of size 200 mm bore class PN 1.6 with stainless steel spindle including replacement of worn out rubber sheet nut, bolts and washers, including taking down of old and UNSV valve complete all as specified and directed

S&F in replacement of double flanged sluice valve of size 150 mm bore class PN 1.6 with stainless steel spindle including replacement of worn out rubber sheet nut, bolts and washers, including taking down of old and UNSV valve complete all as specified and directed

Taking out/ lifting defective submersible pump set capacity 12.5 to 15 HP motor from bore well including motor, column pipes, steel rope, submersible cable and accessories etc for its further repair all as directed..

Lowering only submersible pump set along with motor, column pipes, steel rope, submersible cable and accessories etc after repairing including testing commissioning of submersible pump set of 20000 GPH capacity 12.5 to 15 HP motor. Note: All spares required to make the motor, pumps, column pipe etc serviceable shall be measured and paid separately under relevent items as supply only including transportation to & from upto contractor workshop

Rewinding of submersible motor, 12.5 to 15 H.P. 3 Phase, 50 Hz, 415 Volt with PVC insulated / coated copper winding wire of existing gauge with other winding material such as insulating paper, sleeves, bamboo stick etc. as per standard manufacturers specification including cleaning of stator, slots replacement of defective parts and testing complete all as directed . Note :- (a) Winding cut shall be made in presence of Rep of EIC and reassembling shall be done after inspection by the rep of EIC. (b) Rewinding wire of motor will be measured and paid separately under relevent item. (c) The motor shall be squerrel cage induction/slipring induction motor. (d) Spare parts other than winding wire shall be included.

Dismantling of pump motor set complete with 12.5 to 15 HP, (Taken out above/lying U/S in store yard of AGE E/M) cleaning all dismantled spares parts / winding for inspection of Engineer-in-Charge to ascertian the scope of work for repair/replacement of parts.

Supply and fixing epoxy type cable jointing kit 10/16 Sqmm 3 core complete with all the jointing material ferrule insulation tape etc for 1100 Volts flat submersible copper conductor cable.

Machining work required for repair to submersible pump set by straightning, polishing of pump shaft, making screw and key way, including replacement of wornout parts re-assembling pump after repair for smooth functioning of pump. Note :- Fixing payment shall be deemed to be included in quoted rates.

Supply & Fixing of SS impellers for submersible pump set with key and distance bushes suitable for 12.5 to 15 HP pump

Supply & Fixing of submersible pumps set Bearing/ bush upper & lower for 12.5 to 15 HP

Supply & Fixing of submersible pumps set Neck ring for 12.5 to 15 HP

Supply & Fixing of distance sleeves for 12.5 to 15 HP submersible pump set.

Supply & Fixing of GM motor bush upper and lower (set of two) for submersible pump set 12.5 to 15 HP.

Supply & Fixing of coupling with key for motor pump for submersible pump set 12.5 to 15 HP

Supply & Fixing of Sand Guard for submersible pump set for 12.5 to 15 HP

Supply & Fixing of housing upper and lower for submersible pump set 12.5 to 15 HP

Supply & Fixing of Thurst bearing assembly for submersible pump set motor of 12.5 to 15 HP

Supply & Fixing of Casing bearing for submersible pump set 12.5 to 15 HP

Supply & Fixing of Bowl suitable for submersible pump set 12.5 to 15 HP

Supply & Fixing of Flat water proof submersible cable 3 core copper conductor, PVC insulated 1100 volts grade stranded 16 Sqmm 3 Core, ISI marked and connected to pump motor through water tight sealing joints complete all as specified.

M&L for replacement of MS bolt & nuts of different size for column pipes/valves/flanges etc

M&L for replacement of rubber flange 3mm thick upto 100mm bore pipe complete all as specified and as directed

Supply and lowering in bore hole galvanized iron column pipe 100mm dia medium grade (appromimately in 3m lengths) each duly flanged at both ends by welding with specials such as slots for housing and holes for fixing nut bolts including painting with one coat of synthetic enamel paint over a coat of primer, taking out and disposing off old unseviceable pipes complete as specified and as directed

Supply & fixing in replacement of old unserv starter by Automatic Star Delta starter consisiting of ampmetre,voltmetre,indicator lamp,ON/OFF push button,TP MCB etc suitable for motor pump set of capacity 20 P. including making all electric connection complete all as specified.

Servicing , repairing and over hauling of flaculator including replacement of chain and gear box including oiling greasing and making good as serviceable condition all as specified and directed Note :- repairing of flaculator for both tank sedimentation and pre sedimentation tank seperatly)

Servicing repairing and over hauling of slip ring for flaculator all as specified and directed.

Painting and Preparation of surface of steel section incl complete moving bridge and structure of clarifloculator tank /pre sedimentation tank and applying two coat after rubbing of rusted surface of synthetic enamel paint including marking all sign of requisite colour complete all as specified and directed.

Repairing of clarifloculator rubber pading (wheel), bearing, chain, motor and overhauling complete and cleaning well mentained all as specified and directed Note rubber padding taken seperately

Painting of pump motor set, air blower, VT pump etc of applying two coat of synthetic enamel paint after rubbing of rusted surface including marking all sign of requisite colour complete all as specified and directed.

Supply and fixing in replacement of sets of bearings for 1.5 to 5 HP motor of DE and NDE complete all as specified and directed.

Repair and Maint of automatinc star delta starter, decarbonised of all contects, relay,thimbles etc and cleaning, making good, tightning of all cables, wires and other connected items oiling in moving macnisiam etc incl replacement of burnt parts as requirment basis all as specified and directed for 75/100 HP starter complete all as specified and directed .

Repair and Maint of automatinc star delta starter, decarbonised of all contects, relay,thimbles etc and cleaning, making good, tightning of all cables, wires and other connected items oiling in moving macnisiam etc incl replacement of burnt parts as requirment basis all as specified and directed for 15 to 50HP starter complete all as specified and directed .

M&L for maintenance of Motor any type and size Electric supply panel any type and size by replacing / repairing of necessary spares as per existing capacity / type required for healthy operation of the motor like contacts of various types/capacity, over load relay, single phase preventor, voltage fluctuation protector, ammeter/voltmeter of exiting size/capacity and type, 3phase indicator lamps complete all as specified and as directed

M&L for maintenance of power factor improvement correction panel, comprising of PF meter, ammeter, voltmeter, capacitor bank, conductor relay etc suitable for 3 Phase, 415 Volts, 50 Hz panel complete all as specified and as directed. Note Capacitor of required size will be measured and paid separately.

Supply, fixing and testing in repairs water pressure gauge , dial type 100mm nominal dia with control valve, socket, union, and adopter, range 0-100 PSI fixed with 150mm long, 15mm dia GI pipe medium grade with suitable arrangement for fixing on 150/200mm DI/CI by using clamps, complete all as specified and as directed

Supply and fix as in repair electronic motor protection relay type Selec MPR-341-2 or equvalent as per existing type and size and as directed.

Supply and fix as in repair of Contactor of 3 P, AC & DC control 300A, 185a having Aux contact No 02 and NC 02 cat part No IC 185AN3P**22 of HPL or equavalent as per existing type and size and as directed.

Supply and fix as in repair of Contactor of 3 P, AC & DC control 150a having Aux contact No 02 and NC 02 cat part No IC 150AN3P**22 of HPL or equavalent as per existing type and size and as directed.

Supply and fixing in repair MCCB 400 Amp, 4 Pole, 50 Hz, 36 KA magnetic and thermal adjustments type complete as to be fitted in existing size panel all as spd and directed.

Supply and fixing in repair MCCB 250 Amp, 3 Pole, 50 Hz, 25 KA magnetic and thermal adjustments type complete as to be fitted in existing size panel all as spd and directed.

Supply and fixing in repair MCCB 315 Amp, 4 Pole, 50 Hz, 36 KA magnetic and thermal adjustments type complete as to be fitted in existing size panel all as spd and directed.

Supply and fixing in repair MCCB 160 Amp, 3 Pole, 50 Hz, 25 KA magnetic and thermal adjustments type complete as to be fitted in existing size panel all as spd and directed.

Supply and fix as in repair of L&T 66 -110 A Thermal Overload Relays for MNX R4 , 500V, 50Hz, 2Z, AC 15 Max fuse 6A or equavalent as per existing type and sizse and as directed.

Supply and fix as in repair of Contactor of L&T MNX 110 3 Pole Power Contactor 110 A 2 NO + 2 NC CS94137 or equavalent as per existing type and sizse and as directed.

Supply and fix as in repair timer type ET 100 or as per existing type and size and as directed.

Supply and fix as in repair 3 Pole DC control power contactor (LC1E120) 3P(3 NO) - AC-3 - <= 440 V 120A - 24 V AC coil or equvalent as per existing type and size and as directed.

Supply and fix as in repair schneder Overload RELAY LRE 08A class 10A type or as per existing type and size and as directed.

Supply and fix as in repair Electronic Timer -series Micon Tm 175240VAC, 50 Hz, tolerance -20% to 10% ,or as per existing type and size to match the panel and as directed.

Supply & fixing in repair of panel mounted AC Amp meter, three phase square size, flush mounted case, accuracy class - 0.5 complete as per existing type and size to match the panel and as directed.

Supply & fixing in repair of panel mounted AC Volt meter , three phase in square size, flush mounted case, accuracy class - 0.5 complete as per existing type and size to match the panel and as directed.

Supply & Fixing of Bearing as in repair for three phase induction motor of make Kirloskar, 15/20 (KW/20HP) motor part No SKF Deep Groove Ball Bearings, 6309-2Z or as per existing make and type all as directed.

Supply and fixing in repair On load changeover switch 250 Amp, Open Execution, 4 Pole, 415 V AC complete all as spd and directed

Taking down unserviceable copper pipe of any size and type carefully from VT pump set and supply & fixing new copper pipe 1/2" complete including brazing, welding, but bolts and screws of reqd size complete all as existing type and size as directed.

Taking down ball valve as in repair and supply & fixing new brass ball valve of 25 mm complete all as directed.

Taking down ball valve as in repair and supply & fixing new brass ball valve of 20 mm complete all as directed.

Taking down ball valve as in repair and supply & fixing new brass ball valve of 15 mm complete all as directed.

Supply & Fixing of Intermediate Shaft Part No 1840101 complete to match with the Kirloskar vertical turbine pump model BHR 28 Pump model all as directed.

Supply & Fixing of Head Shaft Part No 1850001 complete to match with the Kirloskar vertical turbine pump model BHR 28Pump all as directed.

Supply & Fixing of Impeller shaft Part No 1860101 complete to match with the Kirloskar vertical turbine pump model BHR 28Pump all as directed.

Supply & Fixing of Wearing Ring Part No 1900101 complete to match with the Kirloskar vertical turbine pump model BHR 28Pump all as directed.

Supply & Fixing of Sealing ring Part No 1940101 complete to match with the Kirloskar vertical turbine pump model BHR 28Pump all as directed.

Supply & Fixing of Split Gland Part No 2290001 complete to match with the Kirloskar vertical turbine pump model BHR 28Pump all as directed.

Supply & Fixing of Liquid deflector Part No 2360001 complete to match with the Kirloskar vertical turbine pump model BHR 28Pump all as directed.

Supply & Fixing of Bearing spider Part No 2450101 complete to match with the Kirloskar vertical turbine pump model BHR 28Pump all as directed.

Supply & Fixing of Bearing Spider Lower Part No 2450102 complete to match with the Kirloskar vertical turbine pump model BHR 28Pump all as directed.

Supply & Fixing of Brg Spider lower with WR Part No 2450202 complete to match with the Kirloskar vertical turbine pump model BHR 28Pump all as directed.

Supply & Fixing of Shaft Sleeve Part No 3100001 complete to match with the Kirloskar vertical turbine pump model BHR 28Pump all as directed.

Supply & Fixing of Shaft Sleeve Part No 3110101 complete to match with the Kirloskar vertical turbine pump model BHR 28Pump all as directed.

Supply & Fixing of Shaft Sleeve Part No 3110201 complete to match with the Kirloskar vertical turbine pump model BHR 28Pump all as directed.

Supply & Fixing of Shaft Sleeve Part No 3120201 complete to match with the Kirloskar vertical turbine pump model BHR 28Pump all as directed.

Supply & Fixing of Distance Sleeve Part No 3170001 complete to match with the Kirloskar vertical turbine pump model BHR 28Pump all as directed.

Supply & Fixing of Key Part No 3200101 complete to match with the Kirloskar vertical turbine pump model BHR 28Pump all as directed.

Supply & Fixing of Key Part No 3200201 complete to match with the Kirloskar vertical turbine pump model BHR 28Pump all as directed.

Supply & Fixing of Key Part No 3200401 complete to match with the Kirloskar vertical turbine pump model BHR 28Pump all as directed.

Supply & Fixing of Key Part No 3210001 complete to match with the Kirloskar vertical turbine pump model BHR 28Pump all as directed.

Supply & Fixing of Key Part No 3230301 complete to match with the Kirloskar vertical turbine pump model BHR 28Pump all as directed.

Supply & Fixing of Key Part No 3280001 complete to match with the Kirloskar vertical turbine pump model BHR 28Pump all as directed.

Supply & Fixing of Impeller and Nut Part No 3300201 complete to match with the Kirloskar vertical turbine pump model BHR 28Pump all as directed.

Supply & Fixing of Shaft Sleeve Nut Part No 3340001 complete to match with the Kirloskar vertical turbine pump model BHR 28Pump all as directed.

Supply & Fixing of Bearing nut Part No 3350001 complete to match with the Kirloskar vertical turbine pump model BHR 28Pump all as directed.

Supply & Fixing of Lock nut Part No 3360101 complete to match with the Kirloskar vertical turbine pump model BHR 28Pump all as directed.

Supply & Fixing of Rubber bearing lower Part No 3540101 complete to match with the Kirloskar vertical turbine pump model BHR 28Pump all as directed .

Supply & Fixing of Rubber bearing Part No 3540501 complete to match with the Kirloskar vertical turbine pump model BHR 28Pump all as directed.

Supply & Fixing of Rubber bearing Part No 3570101 complete to match with the Kirloskar vertical turbine pump model BHR 28Pump all as directed.

Supply & Fixing of Journal Bearing Part No 3710001 complete to match with the Kirloskar vertical turbine pump model BHR 28Pump all as directed.

Supply & Fixing of SCR. Coupling Part No 3950101 complete to match with the Kirloskar vertical turbine pump model BHR 28Pump all as directed.

M & L for Gland Packing for pumpmotor set as per the existing size and type complete all as directed.

Supply & Fixing of CI Impeller I-Stg DSM 125-40 (Full dia) Part No 1570001 complete to match with the Kirloskar DSM 125/40 Pump set all as directed.

Supply & Fixing of CI Impeller II-STG DSM 125-40 (Full dia) Part No 1580001 complete to match with the Kirloskar DSM 125/40 Pump set all as directed.

Supply & Fixing of pump shaft (CS40C8) Part No 1800001 complete to match with the Kirloskar DSM 125/40 Pump all as directed.

Supply & Fixing of wear Ring Part No 1900001 complete to match with the Kirloskar DSM 125/40 Pump all as directed.

Supply & Fixing of Shoulder Ring 63 DX10L Part No 1990101 complete to match with theKirloskar DSM 125/40 Pump all as directed.

Supply & Fixing of Interstage Ring Part No 2040001 complete to match with the Kirloskar DSM 125/40 Pump all as directed.

Supply & Fixing of Split lantern Ring Part No 2270001 complete to match with the Kirloskar DSM 125/40 Pump all as directed.

Supply & Fixing of Gland Part No 2290001 complete to match with the Kirloskar DSM 125/40 Pump all as directed.

Supply & Fixing of Liquid Defletor-48D (Na Rubber) Part No 2360101 complete to match with the Kirloskar DSM 125/40 Pump all as directed .

Supply & Fixing of Brg Cartridge-DE Part No 2410001 complete to match with the Kirloskar DSM 125/40 Pump all as directed.

Supply & Fixing of Brg Cartridge-NDE Part No 2530001 complete to match with the Kirloskar DSM 125/40 Pump all as directed .

Supply & Fixing of Bearing Cover Part No 2700001 complete to match with the Kirloskar DSM 125/40 Pump all as directed..

Supply & Fixing of Bearing Cap Part No 2740001 complete to match with the Kirloskar DSM 125/40 Pump all as directed..

Supply & Fixing of shaft sleeve Part No 3100001 complete to match with the Kirloskar DSM 125/40 Pump all as directed..

Supply & Fixing of Bronze Shaft Sleeve nut Part No 3340001 complete to match with the Kirloskar DSM 125/40 Pump all as directed..

Supply & Fixing of lock nut M45X1.5 RH Part No 3360101 complete to match with the Kirloskar DSM 125/40 Pump all as directed..

Supply & Fixing of Throat Bush Part No 3500001 complete to match with the Kirloskar DSM 125/40 Pump all as directed..

Supply & Fixing of set of keys Part No SSOK1 complete to match with the Kirloskar DSM 125/40 Pump all as directed..

Supply & Fixing of Set of Gland Packing Part No SSOG complete to match with the Kirloskar DSM 125/40 Pump all as directed..

Supply & Fixing of Set of O Rings Part No SSOR1 complete to match with the Kirloskar DSM 125/40 Pump all as directed..

Supply and fixing of Set of bearing for 1.5 HP motor (for sedimentation/clariflocculator unit) of end carriage drive complete all to match with the motor all as directed.

Supply and fixing of Set of bearing for Premium reduction gear box (A-337 of end carriage drive complete all to match with the motor all as directed.

Supply and fixing of Worm Shaft for A-377 Gear Box complete all to match with the motor all as directed.

Supply and fixing of Set of Oil seals for A-337 Gear Box complete all to match with the motor all as directed.

Supply and fixing of Set of cabon brush (motor cap 1.5 to 2 HP) for the central current collector complete all to match with the motor all as directed.

Supply and fixing of Central current collector complete all to match with the motor (motor cap 1.5 to 2 HP) all as directed.

Supply and fixing of CI wheel (for sedimentation and clariflocculator unit) with rubber padding, plummer block with bearing for end carriage drive complete all to match with the motor all as directed.

Supply and fixing of Set of bearing for 1 HP motor

Supply and fixing Set of bearing for 2 HP motor of the flocculator drive complete all to match with the motor all as directed.

Supply and fixing Set of bearing for Premium V-400 reduction gear box of the flocculator drive complete all to match with the motor all as directed..

Supply and fixing Worm Shaft for V-400 Gear Box complete all to match with the motor all as directed.

Supply and fixing Set of Oil seals for V-400 Gear box complete all to match with the motor all as directed.

Supply fix as in repair of ductile iron pressure pipes, flange ends K-9 centrifulally cast of nominal bore 300mm , laid in trenches or fixed on blocks or laid on surface complete all as spd and directed

S& F as in repair joint with rubber or fibre board gasket for flanged pipes and pipe fitings of size 300 mm bore complete all as spd and directed.

M & L for DI/CI fittings for spigot socketed/flanged pipes such as bends, tappers, tee pieces single/double branches any tpe and angle /radious and straight connecting pieces for size upto 300 mm complete all as spd and directed.

Taking up old rusted / unserviceable CI / DI water main pipes upto to 300 mm bore with spigot and socketed / flanged ends with all fittings including burning out lead joints and recovering lead, etc. and disposing off complete all as specified and as directed of the following sizes: Note: Excavation and earthwork shall be measured and paid for separately under respective items

Excavation in trenches in Hard and dense soil n.exc 1.5 m wide and n.exc 1.5 m in depth for foundation of poles,cable laying etc, including forming bottom surface to required level and getting out in soft/loose soil all as specified and directed.

Returning, filling in soil/loose soil including spreading, leveling,watering & well ramming in layers not .exceeding 25 cm thick complete all as specified and directed.

Removing of surplus spoil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified.

M&L for PCC 1:4:8 type D2 using 40mm graded mechanically crushed stone aggregates for making good disturbed surfaces of roads / hard standing, etc. and finishing the top surfaces even and smooth without using extra cement complete all as specified and as directed

Supply and fixing as in repair of Polypropylene Filter Nozzles for Rapid gravity filters as per sample and as directed..

Supply and fixing as in repair of Polypropylene Air Stems for rapid gravity filters as per sample and as directed..

Supply and fixing 14/25 mesh fine sand filter media as per sample and as directed..

Supply and fixing 6/14 mesh coarse sand filter media as per sample and as directed..

Supply and fixing 1/4" x 1/10" gravel filter media all as per sample and as directed..

Supply and fixing as in repair of Set of bearing for Air Blower Model SMW 713 AC complete all as directed..

Supply and fixing as in repair of Air Filter for the Air Compressor, Cap 30 HP / 22 KW, 415 Volts, 1475 RPM complete all as directed..

Supply and fixing as in repair of set of oil seals for the Air Compressor, Cap 30 HP / 22 KW, 415 Volts complete all directed by EIC.

Supply and fixing as in repair of V belts for the Air Compressor, Cap 30 HP / 22 KW, 415 Volts, 1475 RPM complete all as directed..

Supply and fixing as in repair of Set of bearing for monoblock pump set of 7.5 KW, 10 HP, 2900 RPM, Model KDS-1030 complete all as directed..

Supply and fixing as in repair of Impeller for KDS 1030 Pump set complete all as directed..

Supply and fixing as in repair of Shaft with Rotor for KDS-1030 Pump set complete all as directed..

Supply and fixing as in repair of SS Strainer Basket for 100 mm T type hair strainier complete all as directed..

Supplying, lowering and fixing of MS casing pipe ERW, 8mm wall thickness both end flanged Column Pipe of size 200 mm bore , with flanged having minimum 08 holes duly welded with MS pipe at both end, fixing with the existing bore hole/jackwell pipe with suitable size nut ,bolt and washers complete to match with the existing alignment of VT pump complete all as spd and dir by EIC.

S& F as in repair of fabrication of VT pump Net from MS steel sheet/Wire (as per sample given) having height of 45 CM and dia of 40 Cm, of weight not less than 25 kg the net (size of hole in net will be as per sample provided) to be fixed with VT shaft in suction line of VT pump inside the jackwell with suitable size nut, bolt and washers all as directed..

M&L as in repair for earthing as per IS:3043 with galvanized steel earth plate electrode 600 x 600 x 6.0 mm thick buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metre below normal ground level connected to galvanized iron Strip 32 x 6 as earthing lead protected by GI pipe medium grade 15 mm bore for protection of GI earth wire and 20 mm dia GI pipe medium grade for watering with alternate layers of charcoal /coke and salt including all accessories like nut, bolts, reducer, nipple, wire meshed/screened funnel and making brick masonry finished chamber of internal size 300 mm x 300 mm x 300 mm with concrete base, covered with PCC cover which shall be embedded in the block masonry including excavation works, refilling, connected to main switch/MCB DB for feeding the electric supply to domestic quarters compete all as specified as shown in electricall plateNo. 3 of SSR Part-I and testing of earth resistance as required. Note : Earthing lead/G.I.Earth wire upto 7.5 metre length shall be deemed to be included in quoted unit rate beyond 7.5 metre, the same shall be measured and paid separately).

Replacement of single phase preventer relay for protection of motor 100/75 HP motor and connection with existing starter/LT panel all as specified and directed.

Replacement of over current relay for protection of motor 100/75 HP motor and connection with existing LT panel/starter

Replacement of dry motor run protection relay or under load relay for 75/100 HP motor

Replacement of CTs as per exisiting capacity upto 250 AMP and connected with existing panel/electric connection

LUXMI ELECTRONIC WORKS

DAVINDER SINGH

PAWAN KUMAR GOVT. CONTRACTORS