Development of Climate resilient coastal fishermen village at Erayumanthurai in Kanniyakumari District

Amount

Earthwork excavation for foundation and basement in all classes of soils, sub soils and ordinary soil loose soil, in Sand, Silt or other loose soil, wet sand or silt not under water, light black cotton soil sandy loam and ordinary soil including excavated earth SS 20.B wet sand except hard rock requiring blasting with an initial lead of 10M and lift of 2 M including shoring, strutting and bailing and water strutting and bailing and water wherever necessary and refilling the side of foundation with excavated earth laid in layers of not more that 15 cm thick well watered and consolidated and depositing the surplus earth as directed by the department officers etc., complete as per standard specifications - Narrow cutting.

Cement concrete of mix 1:4:8 (One cement four sand and eight aggregate) using 40mm gauge HBG Jelly for foundation and flooring including cost and conveyance of all material and labour charges for laying land in layer of not more than 15cm thick well rammed and curing etc., complete

Supplying and filling in foundation, basement, etc with filling crushed stone sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Refilling with excavated earth other than crushed stone sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officers in layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification

Cement Concrete 1:3:6 (One Cement, Three sand and Six broken stone jelly) using 20mm size hard broken stone jelly including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the departmental officers.

Supplying and Filling with conveyed earth in layers not more than 15cm thick well rammed and consolidated etc., completed per standard spectification

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid)

(a) For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

(c) For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc.

Reinforced Cement Concrete 1:1½:3 (one cement, one and half sand & three of HBG stone jally) using 20 mm. gauge hard broken granite stone jelly for all RCC items of works with minimum cement content of 430.80Kgs/ Cum of concrete, excluding cost of reinforcement grill and fabricating charges centering strutting and shuttering but including laying vibrating with mechanical vibrator finishing curing etc., completed as directed by the department officers.

a) For Foundation & Basement

b) For Superstructure

Supplying and fabricating and placing in poisition of MS (or) RTS grills for all RCC Works including cost of steel and binding wire and labour charges for cutting bending tying etc., complete., Steel rod of all sizes - Plain

Brick work in cement mortar 1:5, using country bricks of size 8 ¾"x 4¼"x2¼" for foundation and basement and superstructure etc., complete.

a) For Foundation & Basement

b) For Superstructure

Brick partition walls using best quality using Country Bricks of size 8-3/4" x 4-1/4" X2-3/4" in Cement Mortar 1:3 (One Cement and Three crushed stone Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

Supplying and fixing of M.S.grill of approved design for open courtyard, grill, grill work to doors and window openings etc., using necessary mild steel flats for inner and outer members which should be fixed on edges including priming coat of best approved quality red oxide primer etc., complete complying with standard specification.

Supplying and Filling the basement with Gravel earth in layers of not exceeding 15cm thick well rammed and consolidated etc.

Special plastering with cement mortar 1:3 - 10mm thick for RCC exposed surfaces including curing etc., complete.

Plastering the surface of walls with Cement Mortar 1:3 (One cement and Three plastering sand), 12mm thick in all floors including curing etc., complete complying with standard specification and as directed by the departmental officers.

Paving the floor with best quality Vertified Tiles of size 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three crushed stone sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with pre-polished concrete anti-skid tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three crushed stone sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Dadooing with printed design colour glazed tiles of size 150mm x 150mm x 6mm

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no crushed stone sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Paving the Top of roof with Solar refelective ceramic tiles of size 305 x 305 x 7mm thick of approved quality and colour laid in Cement mortar 1:3 (One cement and three crushed stone sand) 12mm thick and pointed with tile grout (Nitotile Grout or equivalent) and cement in the ratio of 1:3 for joint, curing etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by the Executive Engineer before use on works)

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Crushed stone Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Paving the floor with best approved quality fine polished Kota stone slabs of size 600 x 600 of 18 / 20mm with machine cut edges and matching marble slab not less than 100mm width other than Adanga Marbles as border laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three sand) fixing the slabs in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments and polishing with floor polisher to a high degree of finish etc., The kota stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Painting new iron work with three coats of synthetic enamel paint of approved colour and quality over the existing primary coat in all floor including the cost of paint etc., complete complying with standard specifications and as directed by the departmental officers.( The paint to be used should be got approved by the Executive Engineer before use on the work).

Supplying and fixing 110 mm dia PVC rain water pipe (down full) with necessary bends; shoes and other specials etc., Complete as per standard specification.

Manufacturing, supplying and fixing Precast Reinforced Cement Concrete slabs of following thickness in RCC 1:2:4 (one cement, two sand and four aggregates), using following HBGS jelly excluding cost of reinforcement steel in position but including cost of moulding charges, casting of slab, finishing, curing and fixing in position in all floors etc., complete complying with standard specification and as directed by the departmental officers

Supplying and fixing in position white / colour glazed European Water Closet of best quality and approved make with 100 mm "P" or "S" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings..... (e) White glazed European Water Closet with 12.5 litre capacity porcelin flushing tank fixed on to wall

Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).

Supplying and fixing best quality and make of ready mixed HDPE water storage tanks having 1000 litres capacity made of PVC materials including necessary provision for conveying, jointing delivery lilne, scour pipe, over flow pipe et c., and lifting the tank to the top of the building placing in position etc., complete as directed by the departmentaal officers. etc complete.

Construction of INSPECTION CHAMBER of size 0.60mx0.60m sizes including earth work excavation, CC 1:5:10 of 10 cm thick and brick work in Cement Mortar 1:5 [One cement and Five sand] using best quality of second class Table Mould Bricks of size 9" x 43/8" x 23/4" with Plastering with Cement Mortar 1:3 [One Cement and Three Sand] 12 mm thick to inner and outer sides and wearing coat 1:3:6 [One Cement, Three Sand and Six Aggregate] 15 cm thick and covered with precast slab 5 cm thick etc., complete complying as directed by the departmental officers as per standard specification.

Supplying and fixing in position 15mm dia brass CP screw down tap / Pillar tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)

Supplying and fixing position CI Nahani Trap / Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)

Supplying and fixing AC ventilating shaft of 100mm dia with 3 metre height including cost of 100mm dia AC cylindrical cowl of best approved quality etc., complete complying with standard specifications and as directed by the departmental officers

Supplying, laying and jointing PVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing PVC specials using PVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works.

25 mm dia - PVC Delivery line

25mm dia - PVC Tee

25mm dia - PVC Bend

25mm dia - PVC elbow

25mm dia - PVC coupler

32 mm dia - PVC Delivery line

32mm dia - PVC Tee

32mm dia - PVC Bend

32mm dia - PVC elbow

32mm dia - PVC coupler

110mm dia - PVC pipe

25mm dia Gun metal Gate valve

32mm dia Gun Metal Gate Valve

Painting two coats with ready mixed plastic Emulsion paint of first class quality paint and of approved color over a Preventive coat, including through scraping clean removal of dirt etc., complete including necessary plaster of pairs putty where ever necessary.

Fabricating, Supplying and fixng in position of steel sheeted windows ( Three Leaves) with the following specifications. Outer frames of windows made of 'Z' section F7D of size 33 x 25 x 3mm at 1.419 kg/ m and mullion 'J' section (F4B) of size 46x25x3mm at 2.28kg/m and shutter section of made of F7D of 33x25x3mm at 1.419 kg/m as specified in IS 7452/1990. Each openable shutter should not exceed a width of 600mm to enable separate operations and easy maintenance. The panel of the shutters to be covered with 18 gauge cold rolled sheet of superior quality and welded intact with shutter frames. Horizontal stiffeners using 18x5mm MS Flat at 0.70kg/m at 3 Nos. for each shutter and additional diagonal stiffners of the same MS flats at all the four corners of each shutters to the suitable length welded to the shutters, for holding the CR Sheets in position firmly.2 numbers of sturdy hinges and one number of handle-cum-latch of special type made with 18x5mm MS flats are revetted to the shutters at an appropriate height in window. suitable opening is left for its easy operation. a stopper square rod for handle is provided in the mullion section at suitable place to catch the window handle. each window shutter having an adustable stay made out of 18 x 5mm at 0.70 kg/ m MS flat of lenght 320mm with three adjustable position. A matching peg is provided in the outer frame of the window at suitable place. 4 Nos. of hold fasts of 120mm length spliced at the ends are welded to the outer frame of the window by using MS flat of 18x5mm at 0.70kg/m, welded to the shutter at two place equivalent from each from top and bottom of the shutter.An MS square bar of 12mm size is welded to the inner face of the window at an equal interval not exceeding 100mm edge between them. All members are painted with one coat of anti-corrosive red oxide primer as directed by the departmental officers.All sections should be in confirmed with IS 7452/1990.The cost includes cost of all materials, labour charges and other incidental charges, etc., complete

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x6mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.

Supplying, fabricating and fixing inposition Aluminium anodised natural colour matt finish louvered ventilator size 600mm x 600 mmof with outer frame section with 62x38x2mm at 1.174 kg/m and the louvered with moving arrangements made with aluminium channel of size 60x30x4mm @ 1.274 kg/m ALuminium clips 19.05x17.27/ 11.05x0.075mm @ 0.169kg/m with necessary 4mm thick plain glass panel for louvers including cost of all materials, labour and power required for fabrications, chipping dismantling making holes in RCC, masonry and made good to the original condition after fixing etc., complete. The Aluminium surface is to be anodised with matt finish under electrically controlled condition in accordance with ISI specification 1868/1962 for anodic film thickness of notless than 15 Microns,etc., complete.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over one coat of red oxide priming coat in all floors including cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Solid PVC Door Shutters using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC Sheets. Shutter using 5mm thick solid PVC Sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm with suitable rabate for housing the shutter (Solid panel pvc door with frame) (M-0391 P.No.81 SOR 2024-25)

Supplying and Erecting Pull and Push Type Rolling Shutter with ISI make of approved size and section using 18 GI sheet. The shutter shall be painted with one coat of red oxide primer and the rate is inclusive of hood covers, transportation charges etc

Solid core Flush shutters with commercial ply on both side with teak wook lipping alround 35 mm thick

Supplying and fixing door shutters for Medium Density Fibre board of exterior grade, Plain with Teakwood external lipping alround of 35 mm thick conforming to IS 12406 / 1989 with 35 x 12mm T.W. on all edges with necessary adhesive and C.P. screws, including fixing of aldrops, tower bolts, hinges and lock strike plates, putty, fevical, varnish for T.W. lipping with thinner colouring agent etc., The rate includes cost of materials and cost for aluminium furniture fittings such as 6 nos Alu. hinges 125mm, 1 no Alu. aldrop 250 x 16mm, 2nos Alu. tower bolt of 300x12mm and 1 no Alu. tower bolt of 200x12mm, 3 Nos Alu. Handles, 2 nos door stopper with rubber bush incase of Single leaf door inclusive of labour charges for fixing in position etc., complete. All Aluminium furniture fittings are to be anodised with matt finish under electrically controlled condition in accordance with ISI specification 1868/1968 for anodic film thickness of not less than 15 microns, The rate is inclusive cost of fevical and fixing charges, transportation, loading, unloading and all other incidential charges, handling charges etc., complete complying with standard specification.

Supplying and Fixing of 5 star rated inverter (Carrier/Voltas/o General / Equivalent) 2 Ton Inverter Spilit AC for Large room and one year warranty including cost of material and fixing charges. SOR XIV 1 M-1985 (Page No.208)

UPVC Ventilator Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Wiring with 2x4 sq mm PVC insulated SC unsheathed Cu. conductor cable of I100V. Plinth in suitable PVC casing on wall ci ceiling with bP switch box, non inter locking C.5. plug with continuous earth wire connection of 14 SWGTC wire far open PVC power plug point SD 13

Wiring with 2 x 1.5 sq.mm PVC insulated single core unsheathed copper conductor cable 1100 V. Plinth in suitable PVC pipe on wall/ceiling with all accessories with continuous earthwire connection of SWG TC wire for open PVC Iight point SD.16

Wiring with 2x 1.5 Sq.mm (22/0.3) PVC insulated single core unsheathed copper conductor cable of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories in flush with wall with 3mm thick hylum sheet cover with TW switch box and 5A F.T switch with continuous earth wire connection of 14 SWG TC wire for making good of the concealed portio with suitable colour for PVC concealed light point / fan point (for Electronic Regulator) - SD 24

Wiring with 2 x 4 sq.mm. (56 / 0.3) PVC insulated SC unsheathed copper conductor cable of 1100V grade in suitable pipe on wall and ceiling with PVC accessories with 150mm x 100mm x 113mm TW switch box for 15A 3 pin non inter locking wall socket with 15A flush type switch with painting of suitable colour with continuous earth wire connection of 14 SWG TC wire for open PVC power plug point (SD 39)

Wiring with 2 x 4 Sq.mm ( 56/0.3) PVC insulated SC unsheathed Cu. Conductor cable of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with 150 mm X 100 mm x 113mm Switch box in flush with wall with 3mm thick hylum sheet cover for 15A 3 pin Non-inter locking Cs Plug with painting of suitable color with continuous earth wire connection of 14 SWG TC wire for concealed power Plug Point. - SD 40

Supply and fixing of single box type 4'36W fluorescent fitting complete with electronic ballast with TW round blocks on wall or ceiling with flu tube with PVC unsheathed Copper leads from terminals to the fitting (SD 87)

Supply and fixing of 1200mm (48") sweep AC ceiling fan complete with stepped electronic 300W regulator with 1 metre down rod with fan clamp with side plates and cross arm of size 450mm (18") (SD 106)

supply and fixing of 48W LED street light fitting with LED (Higher end) with 32mm dia. GI pipe (class B) with 1 no.32 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting . (SD 448)

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) 1 No. 32A DP MCB as incoming and 6 Nos. 6A to 32A SPMCB outgoing in flush with wall and making good of the concealed portion with earth connection only. The MCB DB and MCB's should be with ISI mark (like standard make)(SD 514)

Supply and fixing of 32A TPNMC switch on suitable angle iron frame work with MS cable entry box with earth connection only

Earthing as per PWD standard with an earth electrode of 2 metre Class 'B' GI pipe of dia not less than 32mm complete with necessary masonry work (SD 212)

Supply and run of 4 x 6 sq.mm. (84 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V on 7 / 20 GI bearer wire for service connection mains (SD 368)

Supply and fixing of TNEB meter board suitable for 32A single phase service connection with 32A fuse unit (500V) 32A neutral link and earth link (1" x 1/8" copper flat) on TW plank of size 375mm x 300mm x 19mm with supporting TW reepers of 1" thick an either side with painting with suitable bolt and nuts for fixing the TW plank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit (SD 125)

Supply and fixing of 15A aerial fuse unit (500A) on suitable 100x100mm TW concealed box with hylem sheet on the tapping pole with necessary clamps and as directed by the departmental engineers(SD 130)

Supply and run of 2 of 6sq.mm. (84/0.3) PVC insulated SC unsheathed copper conductor of 1100V on7/20GI bearer wire for service connection mains and as directed by the departmental engineers(SD 66)

Supply and fixing of 32A DP switch of 500V with metal clad with fuse and neutral(sidehandle) on suitable TW board with earth connection only and as directed by the departmental engineers(SD 144)

Wiring with 2x1.5sq.mm. (22/0.3) PVC insulated unsheathed SC copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with TW switch box with 5A FT switch in flush with wall covered with hylum sheet of 3mm thick with painting of suitable colour for open PVC light / fanpoint (for electronic regulator) (5 points per coil) and as directed by the departmental engineers (SD 22)

Supply and fixing of single box type 4'40W fluorescent fitting complete with copper choke and condensor with TW round blocks on wall or ceiling with flu tube with PVC unsheathed copper leads from terminals to the fitting and as directed by the departmental engineers (SD 88)

Supply and fixing of TNEB meter board suitable for 3 phases 63 A service connection made up of suitable angle iron from work of size 2'x1'x1/2' using angle iron of size 1 1/2" x1 1/2" x 1/4" fixed on wal 63 A fuse unit (500V) 1 No. neutral link, and copper earth link (1" x 1/4" copper flat) on with earth connection and inter connection of EB meter to earth unit by 7/16 PVC insulated copper wire with earth connection complete - SD 131

Supply and fixing of 63 A TPN MC switch on suitable angle iron fram work with ms cable entry box with earth connection only - SD 150

Supply and fixing of 3 phase 4 wire ICDB of 16 A per way with 32 A TPN MC switch with suitable trunking box ms cable entry boxes and internal connection on suitable angle iron frame work with with earth connection only - SD 174

supply and fixing of AC/DC 76mm Buzzer/ call bell suitable for 220 Volts 50 C/C single phase AC supply on suitable TW Board with push switch. - SD 105

Supply anf fixing of 30W LED Street Light Fitting with LED suitable for LED Outdoor Fittings (Light Emitting diode, Higher End Philips/Havells/Equivalent) with necessary supporting items. (SD 445)

Supply and run of 2of4sq.mm.(56/0.3) PVC insulated SC unsheathed copper conductor of 1100V grade insuitable PVC rigid pipe on wall and ceiling with continuous earth wire connection of 14SWGTC wire with painting of suitable colour and as directed by the departmental engineers (SD 56)

Supply and fixing of 3 Phase 32 A aerial fuse unit for 3 Nos 32 A fuse units (500A) on suitable MS sheet covered with 6 mm thick hylem sheet on suitable angle iron work the tapping pole with necessary clamps - SD 135

Supplying and fixing of 1200mmm (48") ceiling fan complete with stepped electronic 300 w regulator with 300 mm down rod on the existing clamp - SD 110

Provision for furniture items etc., (As per Quotation)

Provision for Computer Accessories etc., (As per Quotation)

Provision for Locker Arrangements etc., (As per Quotation)

Provision for Puf Panel, Doors and Refrigeration unit & Electrification charges (As per Quotation)

Sub Total Amount for above all items (excluding GST)

GST 18% for above SubTotal Amount

VMP ASSOCIATES (BID ID -1356905)