Providing and fixing Porta Cabin for RWA Office in different locations in RK Puram Assembly Constituency-44.

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

PPGI Puff Panel material used for developing of porta cabin: Material Details for Puff Panel Office (i) Bottom fixing with coated mm thick “C” channel flashing 50x50x50mm with 8mm fastener. (ii)50mm thick powder-coated(PPGI) sandwich puff panel for side wall . (iii) 50x80mm thick powder-coated(PPGI) sandwich puff panel for roof. (iv).Corner panels(inner & outer) covered with PPGI 0.5mm thick powder coated flashing 50x50mm. (V) Roof Corner flashing outer covered with 0.5mm thick ”C” channel flashing 75x75mm. (vi) Cam-lock for holding/joint puff panel sheets covered with PVC lock and cap.(vii)Silicon for fixing joints between every puff panel sheet. (viii)Pop-ripit for fixing flashing with puff panels. (ix) ”L” shape corner outer column flashing 10x100mm. (x)30mmthick puff panel door with patam /chokhat flashing. (xi)Door lock, SS handle,4” SS Kabze. (Xii)Aluminum powder coated sliding windows with aluminum safety grill(4’x3’). (xiii) Electric open fitting with ISO mark wires of 4mm,2.5mm,1.5mm and 0.75mm (xiv)ISO mark switch & socket, LED tube light, mcb and bulket light(outer). (xv)500x500mm vitrified tiles on the carpet area of porta cabin. (xvi) Labour charges fo installation/fixing job of puff panel, tiles and electric work. (xvii)Switch, socket, tubelight and MCB for porta cabin and 02no. separate MCB for spilt AC. (xviii)Separate toilet with WC, washbasin, Urinal and water tap(Size:8'x 4’). (xix) Separate Kitchen with sink , water tap and storage(Size:8'x 4’). (xx) Two nos. of Spilt A.C. 1.5 Ton. Transportation Charge included.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Manufacturing, supplying and fixing retro reflective overhead signage boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type - III of ASTM-D-4956-01 as approved by Engineer-in-charge, letters, borders etc. as per IRC : 67-2001 in silver white with blue colour back ground and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class II of ASTM-D-4956-01 and fixing the same to the plate of structural frame work by means of suitable sized aluminium alloys, rivets or bolts & nuts @ 300 mm centre to centre all along the periphery as well as in two vertical rows along with theft resistant measures, including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminium sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all complete as per drawings, specification and direction of the engineer-in-charge.(Structural frame work including M.S. plate to be provided separately. Rectangular area of the sheet only shall be measured for payment). Overhead informatory road signage