REPAIR/RENEWAL OF FURNITURE AT GE BHARATPUR

Amount

Form with back/without back (FD- 77 M, FD- 78, FD-1027):-Taking out old unserviceable seat of form with back/without back (FD- 77 M, FD- 78, FD-1027) and S&F new plank on seat of form with back/without back with nut and bolt with washer of size 65X6mm . Plank should be made of 1 st class hard wood well seasoned (sheesham) free from all knots & creck, rest all as per shown in drawing and directed by Engineer- in-charge.

Form with back (FD- 78(M)):- Taking out old unserviceable back of form with back (FD- 78(M)) and S&F new plank on back of form with back with nut and bolt with washer of size 65X6mm . plank should be made of 1 st class hard wood well seasoned (Sheesham) free from all knots & creck, rest all as per shown in drawing and directed by Engeer- in-charge.

M&L for preparing old painted steel surfaces of form with back/without back (FD- 77 M, FD- 78, FD-1027) with one coat of synthetic enamel paint on surfaces complete all as specified and directed by Engineer-in-Charge.

Charpoy GI Pipe 32mm with MDF ToP (FD-220) :- Taking out old unserviceable MDF top from each charpoy GI pipe 32mm with MDF top (FD-220) and S&F new plywood BWR 6.5'x3'x12 mm thick ISI marked on top with flate head nut & bolt size 10 mmx75 mm long with washer, rest all as per shown in drg & diracted by Engr-in-charge

Taking out old UNSV long rail of charpoy GI 32mm dia (FD-220 & FD-270) plywood top and S&F new long rail. Long rail should be made of 32 mm dia medium grade ISI marked GI pipe, make : Tata/Jindal/Sail of charpoy GI. Rest all as per drg and directed by Engineer-in-charge

Taking out existing old broken short rail from GI charpoy 32 mm dia and providing in position short rails made out of old broken long rail obtained from taking down above item No 05 including threading on both ends complete fixing all as specified and shown on drg and by the Engineer-in-charge.

Taking out existing old broken legs from charpoy and providing in position made out from GI pipe 32 mm dia obtained from item No 06 & S&F IInd class HW block fitted at bottom of leg with screw and two nos MS clamp made out 25 x 3 mm size and welded legs incl painting of clamps with two coat of synthetic enemel black paint over a coat of red oxide primer complete all as specified and directed and by the Engineer-in-charge.

Taking out old unserviceable three way elbow from long rail/short rail etc of charpoy GI plywood (FD-220). Supply and fixing in position new three way elbow 32mm dia med. grade (ISI marked) all as per drg and directed by the Engineer-in-charge.

Taking out old unserviceable check nut from long rail/short rail etc of GIP/IP charpoy pltwood top (FD-220 ) and supply and fixing in position new check nut 32mm dia 6mm thick complete all as per drg and directed by the Engineer-in-charge.

Supply and fixing of flat Iron size of 40x6 mm from each charpoy GI pipe 32mm with support flate Iron 40x6 mm and two Nos fixing and welding each charpoy all as per shown in drg & diracted by Engr-in-charge

Charpoy Charpoy GI Pipe 32mm with nylone niwar (FD-220 & FD- 270) :-Taking out old unserviceable nylone niwar from existing charpoy Charpoy GI pipe 32mm with nylone niwar (FD-220 & FD- 270) and charpoy GI folding and complete reviving with new nylone niwar 50-55 mm wide, double knitted complete all as specified and directed by Engineer - in charge. ( colour of nylone newar should be light or mixed colour and weight not be less than 1.5 Kgs for each charpoy.

Taking out old UNSV long rail of charpoy GI 32mm dia (FD-220 & FD-270) nylone niwar and S&F new long rail. Long Rail should be made of 32 mm dia medium grade ISI marked GI pipe, make : TATA/JINDAL/SAIL of charpoy GI. Rest all as per drg and directed by Engineer-in-Charge

Taking out existing old broken short rail from GI charpoy 32 mm dia and providing in position short rails made out of old broken long rail obtained from taking down above item No 12 including threading on both ends complete fixing all as specified and shown on drg and by the Engineer-in-charge.

Taking out existing old broken legs from charpoy and providing in position made out from GI pipe 32 mm dia obtained from item No 13 & S&F IInd class HW block fitted at bottom of leg with screw and two Nos MS clamp made out 25 x 3 mm size FI welded legs incl painting of clamps with two coat of synthetic enemel black paint over a coat of red oxide primer complete all as specified and directed and by the Engineer-in-charge.

Taking out old unserviceable three way elbow from long rail/short rail etc of charpoy GI nylone niwar (FD-220 ). Supply and fixing in position new three way elbow 32mm dia med. grade ( ISI marked ) all as per drg and directed by the Engineer-in-charge.

Taking out old unserviceable check nut from long rail/short rail etc of GIP/IP charpoy nylone niwar (FD-220 ) and supply and fixing in position new check nut 32mm dia 6mm thick complete all as per drg and directed by the Engineer - in - charge.

Almirah steel large/ Medium/Small (FD-67M, FD-1032, FD-243, FD-1033, FD-1034 :-Taking out existing old MS handle of almirah steel large/medium/small (FD-67M, FD-1032, FD-243, FD-1033, FD-1034). S&F new MS handles chromium plated (ISI marked, make :- Godrej/Rina/Link) suitable for almirah steel large/ medium/small. MS handle chromium plated will fixed with shutter of almirah steel large/medium, rest all as per Drg and directed by Engr- in-Charge.

Taking out existing old lock of almirah steel large/medium/small (FD-67M, FD-1032, FD-243, FD-1033, FD-1034). S&F new lock with double key (ISI marked, make :- Godrej/Link) suitable for almirah steel large/ medium. Lock with double key will fixed with shutter of almirah steel large/medium, rest all as per Drg and directed by Engr- in-Charge.

Repairing lock godrej pattern of almirah steel large/medium/small (FD-67M, FD-1032, FD-243, FD-1033, FD-1034) to make it serviceable condition by making new keys in duplicate all as specified and directed by Engineer-in-Charge.

Taking out existing old lock cap of almirah steel large/medium/small (FD-67M, FD-1032, FD-243, FD-1033, FD-1034). S&F for new lock cap of almirah steel large/medium. Lock cap will be fixed by riveted or screws as applicable, rest all as per Drg and directed by Engineer-in-Charge.

Taking out existing old Unsv leg portion of almirah steel large (FD-67M, FD-1031, FD-1034) and S&F new leg portion by welding of leg portion made to shape by 18 gauge plain sheet (1.2mm) of size 470 x 82 x 100 mm duly painted by two coats of synthetic enamel paint after a coat of red oxide primer. Rest all as per Drg and directed by Engr- in-Charge.

Removing of old Unsv leg portion of Almirah steel medium/Small (FD-1032, FD-243, FD-1034) and S&F new leg portion by welding of leg portion made to shape by 18 gauge plain sheet (1.2mm) of size 415 x 82 x 100 mm duly painted by two coats of synthetic enamel paint after a coat of red oxide primer as directed by Engineer-in-Charge

(FD-67M, FD-1032, FD-243, FD-1033, FD-1034) : Fixing only of steel sheet shelves in almirah of any thickness and any size / shape by providing new screws or brackets or stoppers as fixed in repair as directed by Engr-in-Charge.

(FD-67M, FD-1032, FD-243, FD-1033, FD-1034) S&F godrej pattern hinges of MS and shape & size as existing in steel almirah by fixing duly welded if required all as directed by Engr-in-Charge.

M&L for preparing old painted steel surfaces of steel almirah (large) (FD-67M, FD-1031, FD-1033) and painted to all internal and external surfaces complete by spray/Brush with one coat of synthetic enamel paint (OG).

'-do- all as item No 25 but steel almirah medium and Small '(FD-1032, FD-1034)

Locker Bed Side Steel FD-1029, FD-257 :- Removing of old leg portion of locker bed side steel FD-1029, FD-257 and S&F new leg portionby welding of leg portion made to shape by 18 gauge plain sheet (1.2mm thick) duly painted by two coats of synthetic enamel paint after a coat of red oxide primer rest all as per drg and directed by Engineer-in-Charge

Taking out existing old MS handle of locker bed side steel (FD-1029, FD-257). S&F new MS handles chromium plated suitable for locker bed side steel. MS handle chromium plated will fixed with shutter of locker bed side steel, rest all as per Drg and directed by Engr- in-Charge.

Taking out existing old UNSV haspe and staple of locker bed side steel (FD-1029, FD-257). S&F new hapse and staple suitable for locker bed side steel,rest all as per Drg and directed by Engr- in-Charge.

M&L for preparing old painted steel surfaces of locker bed side steel (FD-1029, FD-257) and spray/brush painted with one coat of synthetic enamel paint(OG) to all internal and external surfaces complete

Chair CB Steel with arms FD - 75M :- Removing of old UNSV arms of chair CB Steel with arms FD - 75M and S & F new arms of chair CB steel office(FD75(M). Arms should be made of II nd class HW of size 450X50X25 mm with painted with two coats of black synthatic enamal paint over a coat of pink primer after preparation of surface and fixing to chair with 75 mm long full threaded steel screws ,washers and nut bolts as applicable. Rest all as per drg and directed by Engineer- in- Charge.

M & L for back frame of chair CB steel with arms (FD75(M), FD-78M) made up of IInd class HW back frame of size 368X460 mm of section 40X25 mm duly caned with white coloured of 2 to 2.5mm wide half round cane and bordered with 3.5 mm half round cane and painted with two coats of black synthatic enamal paint over a coat of pink primer after preparation of surface and fixing to chair with 75 mm long full threaded steel screws ,washers and nut bolts as applicable including taking down old unserviciable back completed all as spacified and directed by Engineer- in- Charge.

All as per item ser No 32 but size of seat frame 460X440 mm.

M&L for prepairing old painted steel surfaces of chair CB steel with arms (FD75(M), FD-78M) with one coat of synthatic enamal paint on surfaces complete all as spacified and directed Engineer- in- Charge.

Taking out of old unserviceable pvc hard rubber ring of chair CB Steel with arms (FD75(M), FD-78M) and S & F new pvc hard rubber ring of chair CB Steel with arms . PVC hard rubber ring should be best quality , rest all as per shown in drawing and directed by Engeer- in-charge.

All as per item ser No 32 but chair CB steel without arms (FD75(M).

All as per ser No 32 but size of seat frame 460X440mm of chair CB steel without arms (FD75(M).

M&L for prepairing old painted steel surfaces of chair CB steel without arms (FD75(M) with one coat of synthatic enamal paint on surfaces complete all as spacified and directed Engineer- in- Charge.

Taking out of old unserviceable pvc hard rubber ring of chair CB Steel without arms FD75(M), FD-78M) and S & F new pvc hard rubber ring of chair CB Steel without arms . PVC hard rubber ring should be best quality , rest all as per shown in drawing and directed by Engeer- in-charge.

FD-34, FD-1003, FD-84, FD-75(M) FD-256, FD-359 ) S&F for frame work any pattern of MS steel furniture by circular shaped pipe 15 mm external dia pipe of 18 SWG thick with required welding work and resetting as per standard Drgs of steel furniture including two coat of synthetic enamel paint over a coat of red oxide primer after preparation of surfaces complete all as specified and directed by Engineer- in- Charge.

'(FD-1007, FD-1008, FD-1009) '-ditto- but 25 mm square/circular shaped pipe hollow section 18 SWG thick.

Chair varandah (FD-256 & FD-359) :- Recaning of chair varandah (FD-256 & FD-359) with plastic cane 5 mm wide (white) including taking out all cane from the chair and one coat painting with synthatic enamal paint in white colour complete all as per shown on drawing and directed by Engineer-in-Charge.

Taking out of old unserviceable pvc hard rubber ring of chair Varandah (FD-256 & FD-359) and S & F new pvc hard rubber ring of chair Varamdah including . PVC hard rubber ring should be best quality & not less than 25mm , rest all as per shown in drawing and directed by Engeer- in-charge.

Recaning of chair varandah (FD-256 & FD-359) with nylon niwar 50 mm wide (white) including taking out all UNSV nylon niwar from the chair and one coat painting with synthatic enamal paint in white colour complete all as per shown on drawing and directed by Engineer-in-Charge.

Taking out of old unserviceable pvc hard rubber ring of chair varandah (FD-259 & FD-357) and S & F new pvc hard rubber ring of chair varandah including . PVC hard rubber ring should be best quality & not less than 25mm , rest all as per shown in drawing and directed by Engeer- in-charge.

Taking out old UNSV table top for table 3'x3' ,table 3'x2' with drawer , table clk office steel, table office officer steel, tepoy map, tepoy varandah. Top should be made of 18 mm thickprelaminated particle board on both faces decorated type exterier grade, including half round teak wood beading around the tabletop with fixed to table frame by steel screw completed.

Book self open large steel FD-69(M)):-Removing of old UNSV shelves of book shelf open large steel and S&F new shelves on the same place with proper nut bolt /welding. Shelves should be made of 01 mm thick plain sheet duly painted by two coats of synthatic enamal paint after a coat of red oxide primer as directed by Engineer-in-charge.

M&L for preparing old painted steel surfaces of book self open large steel FD-69(M) and spray painted with one coat of synthetic enamel paint (OG) to all internal and external surface complete

Book case open small steel:- Taking out existing old shelves of book case open small steel , and S&F new in the same place . shelves should be made of 18 gauge plain sheet (1.2 mm) duly painted by two coats of synthetic enamel paint after a coat of red oxide primer, rest all as per drawing and directed by Engineer-in-charge.

M&L for preparing old painted steel surface of book case open small steel and spray painted with one coats of syntshetic enamel paint(OG) to all internal and external surfaces complete. Rest all as per directed by Engineer-in-charge.

Chair Writing (FD-280, FD-202) :- Taking out of old unserviceable wooden front legs of chair writing and S & F new legs of chair writing including all wood work surface shell be one coat of wood primer. Legs should be made of 1 st class hard wood well seasoned (Teak Wood) free from all knots & creck, rest all as per shown in drawing and directed by Engineer- in-charge.

All as per items ser No 51 above but rear legs of chair writing

All as per items ser No 51 above but front rail of chair writing

All as per items ser No 51 above but rear rail of chair writing

All as per items ser No 51 above but side rail of chair writing

All as per items ser No 51 above but stiffener of chair writing

All as per items ser No 51 above but Arms of chair writing

Taking out of old unserviceable pvc hard rubber ring from various types legs of wooden chairs,tables, bed plywood etc and S & F new pvc hard rubber ring on the legs of wooden chairs, tables & bed plywood etc . PVC hard rubber ring should be best quality & not less than 25mm , rest all as per shown in drawing and directed by Engineer- in-charge.

Prepration of surface of chair writing with fixing all loose wooden parts of furniture by well skilled work men ship and M&L two coat french polish on all exposed surface of chair writing with best work man ship, rest all as per shown in drawing and directed by Engineer- in-charge.

Chair Easy (FD-229 ) :- Taking out of old unserviceable wooden front legs of chair easy and S & F new front legs of chair easy including all wood work surface shell be one coat of wood primer. Legs should be made of 1 st class hard wood well seasoned (teak wood) free from all knots & creck, rest all as per shown in drawing and directed by Engineer- in-charge.

All as per items ser No 60 but rear legs of chair easy.

All as per items ser No 60 but back frame of chair easy.

All as per items ser No 60 but side frame of chair easy.

All as per items ser No 60 but front frame of chair easy

All as per items ser No 60 but rear rail of chair easy.

All as per items ser No 60 but side rail of chair easy.

All as per items ser No 60 but arms of chair easy.

Prepration of surface of chair Easy with fixing all loose wooden parts of furniture by well skilled work men ship and M&L two coat french polish on all exposed surface of chair easy with best work man ship, rest all as per shown in drawing and directed by Engineer- in-charge.

Chair Dinning (FD-279, FD-228) :- Taking out of old unserviceable wooden front legs of chair Dinning and S & F new legs of chair Dinning including all wood work surface shell be one coat of wood primer. Legs should be made of 1 st class hard wood well seasoned (teak wood) free from all knots & creck, rest all as per shown in drawing and directed by Engineer- in-charge.

All as per items ser No 69 but rear legs of chair dinning.

All as per items ser No 69 but fron rail of chair dinning.

All as per items ser No 69 but rear rail of chair dinning..

All as per items ser No 69 but side rail of chair dinning.

All as per items ser No 69 but stiffner of chair dinning.

Prepration of surface of chair dinning with fixing all loose wooden parts of furniture by well skilled work men ship and M&L two coat french polish on all exposed surface of chair dinning with best work man ship, rest all as per shown in drawing and directed by Engineer- in-charge.

Teapoy Wooden (FD-278, FD-382) : Taking out of old unserviceable top of teapoy wooden and S & F new top of teapoy wooden including 3mm thick teak wood beading alround of top. Top should be made of 18/19 mm thick prelaminated particle board bonded with phenol fromaldehyde confirming IS- 3087-1985 one side decorative type other side balansing white, rest all as per shown in drawing and directed by Engineer- in-charge.

Taking out of old unserviceable legs of teapoy wooden and S & F new legs of teapoy wooden including all wood work surface shell be one coat of wood primer axcept where painting is indicated in Drg. Legs should be made of 1 st grade hard wood well seasoned (Teak wood) free from all knots & creck, rest all as per shown in drawing and directed by Engineer- in-charge.

All as per items ser No 77 but Top rail of teapoy wooden.

All as per items ser No 77 but Bottom rail of teapoy wooden

Prepration of surface of teapoy wooden with fixing all loose wooden parts of furniture by well skilled work men ship and M&L two coat french polish on all exposed surface of teapoy wooden with best work man ship, rest all as per shown in drawing and directed by Engineer- in-charge.

Table with Drawer (900 x 600 x 760mm) (FD-283, FD-223) : Taking out of old unserviceable top of table with drawer (900 x 600 x 760) mm and S & F new top of table with drawer (900 x 600 x 760)mm encluding 4mm thick teak wood beading alround of top. Top should be made of 18/19 mm thick pre laminated particle board bonded with phenol fromaldehyde one side decorative type other side balancing white, rest all as per shown in drawing and directed by Engineer- in-charge

Taking out of old unserviceable legs of table with drawer (900 x 600 x 760mm) and S & F new legs of table with drawer (900 x 600 x 760mm) including all wood work surface shell be one coat of wood primer axcept where painting is indicated in Drg. Legs should be made of 1 st grade hard wood well seasoned (teak wood) free from all knots & creck, rest all as per shown in drawing and directed by Engineer- in-charge.

All as per items ser No 82 but top (long) rail of table with drawer (900 x 600 x 760mm).

All as per items ser No 82 but but top (short) rail of table with drawer (900 x 600 x 760mm).

All as per items ser No 82 but but lower rail of table with drawer (900 x 600 x 760mm).

Prepration of surface of Table with drawer with fixing all loose wooden parts of furniture by well skilled work men ship and M&L two coat french polish on all exposed surface of Table with drawer with best work man ship, rest all as per shown in drawing and directed by Engineer- in-charge.

Taking out of old unserviceable drawers of table with drawer (900 x 600 x 760mm) and S & F new drawers of table with drawer (900 x 600 x 760mm) including best quality fancy type PVC knob 32 mm dia, rest all as per shown in drawing and directed by Engineer- in-charge.

Table without Drawer (900 x 600 x 760mm) (FD-284) : Taking out of old unserviceable top of table without drawer (900 x 600 x 760) mm and S & F new top of table without drawer (900 x 600 x 760)mm encluding 4mm thick teak wood beading alround of top. Top should be made of 18/19 mm thick pre laminated particle board bonded with phenol fromaldehyde one side decorative type other side balancing white, rest all as per shown in drawing and directed by Engineer- in-charge

Taking out of old unserviceable legs of table without drawer (900 x 600 x 760mm) and S & F new legs of table without drawer (900 x 600 x 760mm) including all wood work surface shell be one coat of wood primer axcept where painting is indicated in Drg. Legs should be made of 1 st grade hard wood well seasoned (teak wood) free from all knots & creck, rest all as per shown in drawing and directed by Engineer- in-charge.

All as per items ser No 89 but top (long) rail of Table without Drawer (900 x 600 x 760mm).

All as per items ser No 89 but top (short) rail of Table without Drawer (900 x 600 x 760mm).

All as per items ser No 89 but but lower rail of Table with Drawer (900 x 600 x 760mm).

Prepration of surface of table without drawer with fixing all loose wooden parts of furniture by well skilled work men ship and M&L two coat french polish on all exposed surface of table without drawer with best work man ship,rest all as per shown in drawing and directed by Engineer- in-charge.

Table (900 x 900 x 760mm) (FD-291, FD-223) : Taking out of old unserviceable top of table (900 x 900 x 760) mm and S & F new top of table (900 x 900 x 760)mm encluding 4mm thick teak wood beading alround of top. Top should be made of 18/19 mm thick pre laminated particle board bonded with phenol fromaldehyde one side decorative type other side balancing white, rest all as per shown in drawing and directed by Engineer- in-charge

Taking out of old unserviceable legs of Table (900 x 900 x 760mm) and S & F new legs of Table (900 x 900 x 760mm) including all wood work surface shell be one coat of wood primer axcept where painting is indicated in Drg. Legs should be made of 1 st grade hard wood well seasoned (teak wood) free from all knots & creck, rest all as per shown in drawing and directed by Engineer- in-charge.

All as per items ser No 95 but Top rail of Table (900 x 900 x 760mm).

Prepration of surface of Table (900 x 900 x 760) mm with fixing all loose wooden parts of furniture by well skilled work men ship and M&L two coat french polish on all exposed surface of Table (900 x 900 x 760) mm with best work man ship, rest all as per shown in drawing and directed by Engineer- in-charge.

Table Dinning 6 Pers (FD-376, FD-373) : Taking out of old unserviceable top of table dinning 6 pers and S & F new top of table dinning 6 pers mm including 4mm thick teak wood beading alround of top. Top should be made of 18/19 mm thick pre laminated particle board bonded with phenol fromaldehyde one side decorative type other side balancing white, rest all as per shown in drawing and directed by Engineer- in-charge

Taking out of old unserviceable legs of table dinning 6 pers and S & F new legs of table dinning 6 pers including all wood work surface shell be one coat of wood primer axcept where painting is indicated in Drg. Legs should be made of 1 st grade hard wood well seasoned (teak wood) free from all knots & creck, rest all as per shown in drawing and directed by Engineer- in-charge.

All as per items ser No 99 but long rail of Table Dinning 6 Pers.

All as per items ser No 99 but short rail of Table Dinning 6 Pers.

All as per items ser No 99 but Stiffner of Table Dinning 6 Pers.

All as per items ser No 99 but Bracket of Table Dinning 6 Pers.

Prepration of surface of Table Dinning 6 Pers with fixing all loose wooden parts of furniture by well skilled work men ship and M&L two coat french polish on all exposed surface of Table Dinning 6 Pers with best work man ship, rest all as per shown in drawing and directed by Engineer- in-charge.

Chair Wooden Bottom W/O Arms (FD-285, FD-225) : Taking out of old unserviceable wooden front legs of Chair Wooden Bottom W/O Arms and S & F new legs of Chair Wooden Bottom W/O Arms including all wood work surface shell be one coat of wood primer. Legs should be made of 1 st class hard wood well seasoned (Teak Wood) free from all knots & creck, rest all as per shown in drawing and directed by Engineer- in-charge.

All as per item ser No 105 but rear legs of chair wooden bottom W/O arms

All as per item ser No 105 but fron rail of chair wooden bottom W/O arms

All as per item ser No 105 but rear rail of chair wooden bottom W/O arms

All as per item ser No 105 but side rail of chair wooden bottom W/O arms

All as per item ser No 105 but stiffner of chair wooden bottom W/O arms

All as per item ser No 105 but but Back of chair wooden bottom W/O arms

Taking out of old unserviceable ply from chair wooden bottom W/O arms and S & F new plywood on the seat of chair wooden bottom W/O arms . Top should be made of 06 mm thick ISI marked commercial plywood BWR quality , rest all as per shown in drawing and directed by Engineer- in-charge

Prepration of surface of chair wooden bottom W/O arms with fixing all loose wooden parts of furniture by well skilled work men ship and M&L two coat french polish on all exposed surface of chair wooden bottom W/O arms with best work man ship, rest all as per shown in drawing and directed by Engineer- in-charge.

Bed Ply wood top (FD-246/247):- Taking out of old unserviceable ply wood from bed ply wood top and S & F new ply wood 12mm thick, ISI marked commarcial BWR quality on bed ply wood top . Ply wood should be made of 12 mm thick ISI marked commarcial BWR with phenol fromaldehyde, rest all as per shown in drawing and directed by Engineer- in-charge

Taking out of old unserviceable head rest of bed ply wood Top and S & F new head rest with short rail of plywood top. Head rest made of commercial ply wood 4 mm thick (Both side i.e. Inside & outside)with teak wood beading 35mm wide and 6mm thick around of the head rest, rest all as per shown in drawing and directed by Engineer- in-charge.

Taking out of old unserviceable foot rest of bed ply wood top and S & F new foot rest with short rail of plywood top. foot rest made of commarcial ply wood 4 mm thick (both side i.e. Inside & outside)with teak wood beading 35mm wide and 6mm thick around of the head rest, rest all as per shown in drawing and directed by Engineer- in-charge.

Taking out of old unserviceable long rail of bed ply wood top and S & F new long rail of plywood top including all wood work surface shell be one coat of wood primer axcept where painting is indicated in Drg. Legs should be made of 1 st grade hard wood well seasoned (Teak wood) free from all knots & creck, rest all as per shown in drawing and directed by Engineer- in-charge.

Taking out of old unserviceable wooden stiffner of bed ply wood top and S & F new stiffner of bed ply wood top including all wood work surface shell be one coat of wood primer. Stiffner should be made of 1 st class hard wood well seasoned (Teak Wood) free from all knots & creck, rest all as per shown in drawing and directed by Engineer- in-charge.

Taking out of old unserviceable wooden legs of Bed ply wood top and S & F new legs of bed ply wood top including all wood work surface shell be one coat of wood primer. Legs should be made of 1 st class hard wood well seasoned (Teak Wood) free from all knots & creck, rest all as per shown in drawing and directed by Engineer- in-charge.

Prepration of surface of bed ply wood top with fixing all loose wooden parts of furniture by well skilled work men ship and M&L two coat french polish on all exposed surface of bed ply wood top with best work man ship, rest all as per shown in drawing and directed by Engineer- in-charge.

Table Centre (FD-246/247) :- Taking out of old unserviceable top of table centre and S & F new top of Table Centre (900X450X400)mm encluding 4mm thick half round teak wood beading alround of top. Top should be made of 18/19 mm thick pre laminated particle board bonded with phenol fromaldehyde one side decorative type other side balancing white, rest all as per shown in drawing and directed by Engineer- in-charge

Table Centre (FD-246/247) :- Taking out of old unserviceable legs of Table Centre and S & F new legs of Table centrer including all wood work surface shell be one coat of wood primer axcept where painting is indicated in Drg. Legs should be made of 1 st grade hard wood well seasoned (Teak wood) free from all knots & creck, rest all as per shown in drawing and directed by Engineer- in-charge.

All as per items ser No 122 but long rail of Table Centre.

All as per items ser No 122 but short rail of Table Centre.

All as per items ser No 122 but Bottom rail of Table Centre.

Prepration of surface of table centre with fixing all loose wooden parts of furniture by well skilled work men ship and M&L two coat french polish on all exposed surface of table centre with best work man ship, rest all as per shown in drawing and directed by Engineer- in-charge.

Table dressing ladies (FD-378) :- Taking out of old unserviceable mirror of table dressing ladies and S & F new mirror of table dressing ladies as per Drg. Mirror should be made of 5.5 mm thick electro copper plated of polished sheet glass as specified ISI marked best quality, Rest all as per shown in drawing and directed by Engineer- in-charge

Taking out of old unserviceable drawers of table dressing ladies and S & F new drawers of table dressing ladies including best quality fancy type pvc knob 32 mm dia, rest all as per shown in drawing and directed by Engineer- in-charge.

Taking out of old unserviceable top portion of table dressing ladies and S & F new top portion of table dressing ladies , rest all as per shown in drawing and directed by Engineer- in-charge.

Taking out of old unserviceable bottom portion of table dressing ladies and S & F new bottom portion of table dressing ladies , rest all as per shown in drawing and directed by Engineer- in-charge.

Taking out of old unserviceable back portion of table dressing ladies and S & F new back portion of table dressing ladies , rest all as per shown in drawing and directed by Engineer- in-charge.

Taking out of old unserviceable side portion of table dressing ladies and S & F new Side portion of Table dressing ladies , rest all as per shown in drawing and directed by Engineer- in-charge.

Taking out of old unserviceable sliding glass of table dressing ladies and S & F new sliding glass with fancy type pvc knob 32mm dia of table dressing ladies , rest all as per shown in drawing and directed by Engineer- in-charge.

M&L two coat french polish on all wooden surface of table dressing ladies as per shown in FD, rest all as per shown in drawing and directed by Engineer- in-charge.

Table dressing gents FD- 379:- Taking out of old unserviceable mirror of table dressing gents and S & F new mirror of table dressing gents as per Drg. Mirror should be made of 5.5 mm thick electro copper plated of polished sheet glass as specified ISI marked best quality, Rest all as per shown in drawing and directed by Engineer- in-charge

Taking out of old unserviceable top portion of table dressing gents and S & F new top portion of table dressing gents , rest all as per shown in drawing and directed by Engineer- in-charge.

Taking out of old unserviceable bottom portion of table dressing gents and S & F new bottom Portion of table dressing gents , rest all as per shown in drawing and directed by Engineer- in-charge.

Taking out of old unserviceable side portion of table dressing gents and S & F new side portion of table dressing gents , rest all as per shown in drawing and directed by Engineer- in-charge.

Taking out of old unserviceable drawers of table dressing gents and S & F new drawers of table dressing gents including best quality fancy type pvc knob 32 mm dia, rest all as per shown in drawing and directed by Engineer- in-charge.

M&L two coat french polish on all wooden surface of table dressing ladies as per shown in FD , rest all as per shown in drawing and directed by Engineer- in-charge.

Peg Table : Taking out of old unserviceable top of peg table and S & F new top of peg table encluding 4mm thick half round teak wood beading alround of top. Top should be made of 18/19 mm thick pre laminated particle board bonded with phenol fromaldehyde one side decorative type other side balancing white, rest all as per shown in drawing and directed by Engineer- in-charge

Taking out of old unserviceable legs/ top rail of peg table and S & F new legs/top rail of peg table including all wood work surface shell be one coat of wood primer axcept where painting is indicated in Drg. Legs should be made of 1 st grade hard wood well seasoned (teak wood) free from all knots & creck, rest all as per shown in drawing and directed by Engineer- in-charge.

Taking down of old canning from chairs (FD-280 , FD-202, FD-229, FD-279, FD-228) M&L for recanning of both type of chairs with best quality white plastic cane 2 to 2.5mm wide and border with 4mm wide plastic cane. Weaving of chairs shall be godrej pattern, rest all shown in Drg and directed by Engineer-in-charge.

Table office clerk wooden (FD-381) : Taking out of old unserviceable top of Table office clerk wooden and S & F new top of Table office clerk wooden including 6mm thick half round teak wood beading alround of top. Top should be made of 18 mm thick prelaminated particle board bonded with phenol fromaldehyde confirming IS both side decorative type, rest all as per shown in drawing and directed by Engineer- in-charge.

Taking out of old unserviceable legs of table office clerk wooden and S & F new legs of table office clerk wooden including all wood work surface shell be one coat of wood primer axcept where painting is indicated in Drg. Legs should be made of 1 st grade hard wood well seasoned (teak wood) free from all knots & creck, rest all as per shown in drawing and directed by Engineer- in-charge.

All as per items ser No 145 but long rail including concerned side 6mm thick commercial plywood of table office clerk wooden.

All as per items ser No 145 but short rail including concerned side 6mm thick commercial plywood of table office clerk wooden.

All as per items ser No 145 but stiffner of table office clk wooden.

Taking out of old unserviceable drawers of table office clerk wooden and S & F new drawers of table office clerk wooden including best quality fancy type pvc knob 32 mm dia, rest all as per shown in drawing and directed by Engineer- in-charge.

Prepration of surface of table office clerk wooden with fixing all loose wooden parts of furniture by well skilled work men ship and M&L two coat french polish on all exposed surface of table office clerk wooden with best work man ship, rest all as per shown in drawing and directed by Engineer- in-charge.

Table Writing (1145x 600 x 760mm) (FD-275, FD-276) :Taking out of old unserviceable top of table writing (1145 x 600 x 760) mm and S & F new top of table writing including 4mm thick teak wood beading alround of top. Top should be made of 18/19 mm thick pre laminated particle board bonded with phenol fromaldehyde one side decorative type other side balancing white, rest all as per shown in drawing and directed by Engineer- in-charge

Taking out of old unserviceable legs of table writing (1145 x 600 x 760mm) and S & F new legs of table writing (1145 x 600 x 760mm) including all wood work surface shall be one coat of wood primer except where painting is indicated in Drg. Legs should be made of 1 st grade hard wood well seasoned (teak wood) free from all knots & creck, rest all as per shown in drawing and directed by Engineer- in-charge.

All as per items ser No 152 but top (long) rail of table writing (1145 x 600 x 760mm).

All as per items ser No 152 but but top (short) rail of table writing (1145 x 600 x 760mm).

All as per items ser No 152 but but lower rail of table writing (1145 x 600 x 760mm).

Prepration of surface of table writing (1145 x 600 x 760mm) with fixing all loose wooden parts of furniture by well skilled work men ship and M&L two coat french polish on all exposed surface of table writing (1145 x 600 x 760mm) with best work man ship, rest all as per shown in drawing and directed by Engineer- in-charge.

Taking out of old unserviceable drawers of table writing (1145 x 600 x 760mm) and S & F new drawers of table writing (1145 x 600 x 760mm) including best quality fancy type PVC knob 32 mm dia, rest all as per shown in drawing and directed by Engineer- in-charge.

Sofa set 5/4 Seater (FD-281/373) :- Taking out of old unserviceable cushioned seat of sofa set 5/4 seater . S & F new 100 mm thick cool foam 40 D cushion of size 560 mmx560 mm for seat of sofa set 5/4 seater . Cushion shall be covered with best quality tapestry cloth duly stitch. Colour /quality of cloth shall be approved by Engineer-in-charge. Rest all as per shown in drawing and directed by Engineer-in-charge.

Taking out of old unserviceable cushioned back of sofa set 5/4 seater . S & F new 100 mm thick cool foam 40 D cushion of size 560 mmx560 mm for seat of sofa set 5/4 seater . Cushion shall be covered with best quality tapestry cloth duly stitch. Cololur /quality of cloth shall be approved by Engineer-in-charge. Rest all as per shown in drawing and directed by Engineer-in-charge.

Bin solid linen FD-244:-Tacking out old UNSV leg of bin solid linced FD-244. S&F new leg bin solid linced including all wood work surface shell be one coat of wood primer axcept where painting is indicated in Drg. Legs should be made of 1 st grade hard wood well seasoned (Teak wood) free from all knots & creck, rest all as per shown in drawing and directed by Engineer- in-charge.

All as per items ser No 160 but long rail of bin solid linen FD-244.

All as per items ser No 160 but short rail of bin solid linen FD-244 .

Taking out old UNSV top of bin soliid ninen and S&F new top, top should be made of 06 mm thick ISI marked commercial plywood BWR quality with fixing of top sunmika size 36" x 18" incl four side bedding of top of bin solid linced FD-244. rest all as per shown in drawing and directed by Engineer- in-charge.

Taking out old UNSV botom of bin soliid linen anf S&F new botom, botom should be made of 12 mm thick ISI marked commercial plywood BWR quality with fixing of botom size 36" x 18" of bin solid linen FD-244. rest all as per shown in drawing and directed by Engineer- in-charge.

Taking out old UNSV back portion and S&F New back portion, it should be made of 06 mm thick ISI marked commercial plywood with fixing of top sunmika of Size 32 " x 10" of Bin solid linend FD-244. rest all as per shown in drawing and directed by Engineer- in-charge.

Taking out old UNSV front portion and S&F new front portion, front portion should be made of 06 mm thick ISI marked commercial plywood with fixing of top sunmika of Size 32 " x 10", bin solid linced FD-244. rest all as per shown in drawing and directed by Engineer- in-charge.

Tacking out old UNSV side wire mesh of bin solid linen and S&F new side wire mesh of size 14" x 10" in cluding four side beding of wire mess of bin solid linen.rest all as per shown in drawing and directed by Engineer- in-charge.

Prepration of surface of bin solid linen with fixing all loose wooden parts of furniture by well skilled work men ship and M&L two coat french polish on all wooden exposed surface of bin solid linen with best work man ship, rest all as per shown in drawing and directed by Engineer- in-charge.

F.M. KHAN SONS

M/S CHANDER SHEKHAR

AJAY TRADERS

SK INDUSTRIES