North Div Repair work

Earth work n in excavation of foundation trenches of drain or septic tank, soak well etc. in all sorts of soil including removing, spreading or stacking the spoils within a lead of 75 mtr. or as directed and including trimming the sides of trenches, leveling, dressing and ramming the bottom bailing or pumping out water etc. as required complete.a) Depth of excavation not exceeding 1500mm.

b) Depth of excavation for additional depth beyond 1500 mm, and upto 3000mm. But not requiring sharing.

a)Filling in foundation or plinth by fine sand in layer not exceeding 15 cm. as directed and consolidating same by through saturation with water and ramming complete, including the cost of supply of sand. Do by fine sand

b)Earth work in filling in foundation trenches or plinth with good earth in layers not exceeding 150 mm including watering and ramming etc layer by layer complete (Payment to be made on the basis of measurement of finished quantity of work) i)With earth obtained from exavation of foundation.

Single brick flat soling or picked jhama bricks including ramming and dressing bed to proper leveling and filling joint with power earth or local sand including cost of sand or earth.

Brick work with 1st class bricks in cement mortar (1:6) (a) In foundation and plinth

b) In superstructure Gr. Floor

1st floor

2nd floor

125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor.

1st floor

2nd floor

125 mm Thick brick work with 1st class bricks in cement mortar (1:4) in ground floor using approved H.B. netting in every third layer.

Hire and labour charges for shuttering with centreing and necessary staging upto 4 m. using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams, columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor). (When the height of a particular floor is more than 4 m. the equivalent floor ht. shall be taken as 4 m. and extra for works beyond the initial 4 m. ht. shall be allowed under 12(e) for every 4 m. or part thereof.) (Mode of measurement : Area in plan X mean height of staging upto soffit of shuttering above initial 4 m.) a) 25mm. to 30mm. thick wooden shuttering.

c)25mm. to 30mm. shuttering without staging in foundation.

d) Steel shuttering or 9 mm to 30 mm thick approved quality plyboard shuttering in any concrete.

(a)Ordinary cement concrete (mix 1:1:5:3) with graded stone chips (20 mm. nominal size) excluding shuttering and reinforcement, if any, in ground floor as per relevant IS codes, Pakur variety.

1st floor

2nd floor

Ordinary cement concrete (mix 1:2:4) with graded stone chips (20 mm. nominal size) excluding shuttering and reinforcement, if any, in ground floor as per relevant IS codes Pakur variety

1st floor

2nd floor

Reinforcement for reinforced concrete in all sorts of structures work including distribution bars. Stirrups binders etc. initial straightening and removal of loose rust cutting to requisite length, hooking & bending to correct shape, placing in proper position and binding with 1.6 gauge black annealed wire at every intersection, complete as per drawing and direction.Tor steel / Mild steel. SAIL/ TATA/RINL a)For works in foundation, basement and upto roof of ground floor up to 4 m.

Labour for chipping of concrete surface before taking up plastering work.

Scraping of moss, blisters etc.thoroughly from exterior surface of walls necessitating the use of scraper, wire brush etc. (Payment against this item will be made only when this has been done on the specific direction of the Engineer-in-charge)

Stripping off worn out plaster and raking out joints of walls,ceillings etc.upto any height and in any floor including removing rubbish within a lead of 75m as directed.

Plaster ( to wall, floor, ceiling etc.) with sans and cement mortar including rounding off or chamfering corners as directed and racking out joints including throating, nosing and drip course, scaffolding/ staging where necessary. i) With 1:6 cement mortar : a)15mm. thick ( Gr. Floor)

c) 20mm. thick ( Gr. Floor)

ii) With 1:4 cement mortar : a) 10mm. thick ( Gr. Floor) for ceiling bottom of chujja, beam etc.

Artificial stone in floor, dado, straicase etc. with cement concrete (1:2:4) with stone chips laid in panel as directed with topping made with ordinary or white cement (as necessary) and marble dust in proportion (1:2) including smooth finishing and rounding off corners including raking out joints or roughening of concrete surface and application of cement slurry before flooring works using cement @ 1.75 kg/sq.m. All complete including all materials and labour in ground floor. 3mm. thick topping using grey cement. 35 mm

Neat cement punning about 1.5 mm. in wall dado window sills drain etc.

Wood work in door and window frame in fitted and fixed in position complete including a protective coat of painting at contact surface of the frame excluding cost of concrete, iron butt hings and M.S. clams sal (siliguri)

Supplying, fitting & fixing M.S. clamps for door and window frame made of flat bifurcated with necessary screws etc. by cement concrete(4:2:1) as per direction. 40mm. x 6 mm. 250 mm. length.

Oxidised iron butt hinges of approved quality fitted and fixed with steel screw with ISI mark. 100 x 58 x 1.90 mm. (Oxidised)

Supplying, fitting and fixing anodized aluminum barrel / tower / socket bolt 225 mm. long & 10 mm. dia bolt of approved quality make from extruded section with conforming to I.S. 204/74 fitted and fixed with cadmium plated screws 225 mm. long & 10 mm. dia bolt.

Supplying, fitting and fixing anodized aluminum ‘D’ type handle of approved quality manufactured from extruded section confirming to I.S. specification (I.S. 230/72) complete with contibuous plate base. 100 mm. grip x 10 mm. dia rod.

Supplying, fitting and fixing anodized aluminum aldrop / sliding bolt of approved quality manufactured from extruded section confirming to I.S. specification (I.S. 2681/66) complete .250 mm. long by 16 dia bolt.

Door stopper (Brass)

125 mm. long wooden buffer block fitted and fixed complete with necessary screws teak.

M.S. or W.I. ornamental grill of approved design, joint continuously welded with M.S W.I flat sand bars for windows railing etc. fitted and fixed with necessary screws and hugs in ground floor. . Grill weighing above 10kg/m2 and upto 16kg/m2

Collapsible gate with 40 x 40 mm. 6 mm. Tee as top and bottom guided rail 20 x 10 x 2 mm. vertical channels 100 mm. apart in fully stretched position 20x5 mm. M.S. flat as collapsible bracings properly riveted and washered including 38 mm. steel rollers including locking arrangement, fitted and fixed in position with lugs set in cement concrete and including cutting necessary holes chasing etc. in walls, floor etc. and making good damages complete in groung floor (Payment will be made on the area of the gate covered by two guard rails and two extreme channels)

Supplying solid flush type doors of commercial quality the timber frame consisting of top and bottom rails and side style of well seasoned timber 6.5 cm wide each and the entire frame fitted with 37.5 mm. wide battens places both ways in order to make the door of soild core, internal lapping gurjan or similar wood veneers using phenol formaldehyde as gluee etc. complete including fitting and fixing the shutter in position but excluding the cost of hinges and other fittings in groung floor. 32 mm thick shutters ( single leaf)

Supplying, fitting and fixing steel window and ventilators

with or without integrated grills conforming to IS 1038-1975 as per drawing and manufactured from rolled steel section conforming to Is 7452-1974 with non-friction projecting type, box type hinges glazing blips, lung locking brackt, handle plate etc. including hoisting in position, straightering reguired, fixing lugs in cement concrete (1:2:4) with stone chips 20 mm. down cutting holes and mending good damages to match with existing surface complete in all respect excluding glaxing in ground floor, flash butt welded windows and ventilators. . a) Without integrated grill. i) Fixed type steel window as per I.S sizes with horizontal glazing bars.

ii)Open-able steel windows as per I.S.sizes with side hung shutters.

iii) Two point nose steel handle including fitting and fixing.

iv) Aluminium peg stay 300 mm. long including fitting and fixing.

v) Centre hung ventilator as per I.S. sizes 58 cm.

c) Supplying best Indian sheet glass panes set in putty and fitted and fixed with nails and putty complete. ( in all floors for internal wall & upto 6 m height for external wall). 3 mm thick (weighing 7.4 Kg/ Sqm)

Supplying, fitting and fixing Godrej mortice lock (local best approved quality ) 6 lever with handle connected rods and keys crossing a with chromium plated handle.

Supplying, fitting and fixing Godrej mortice lock chromium plated with latch and keys 4 levers, including fitting and fixing complete

Supplying, fitting and fixing in position approved PVC door frame made of extruded PVC multichamber hallow section having dimensions 60mm. x 50 mm. x 2 mm.(+0.2mm.), horizontal section by galvanized steel screws after inserting two number steel brackets as reinforcement making suitable space for placing hinges, one steel tube 40mm. x 20mm. x 1.2mm. will be inserted on one full vertical side of the frame as reinforcement the frame will then be fixed in the opering with the help of PVC expandable fastener wooden gutties and galvanished steel screws including cost of all materials and labour hire charges of all materials, taxes and all other incidental charges complete.

Supplying, fitting and fixing P.V.C door shutter of approved quality and shade in position, the style & rail of the PVC door shutter will be made of rigid PVC multicavity hollow chamber of 50mm. x 30mm. section with 2.0 mm.(+0.2mm.) wall thickness horizontal & vertical section shall be fixed to each other by self tapping screws and one solid ..tools and plants and appliances carriage of all materials, taxes and all other incidental charges complete. The rate is exclusive of cost of hinges, hasp bolt, tower bolt, door ring etc.P.V.C door shutter 30mm. thick :

a) Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality, including smoothening surface by sand papering etc.

b) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality, including smoothening surface by sand papering etc

Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface if necessary. a) On timber or plastered surface with super gloss(hi-gloss) On timber or plastered surface with super gloss(hi-gloss) 2 coats (any shade except white)

b)On steel or other metal surface with super gloss (hi-gloss) 2 coats (with any shade except white)

Cement washing including cleaning and smoothening surface thoroughly external surface one coat.

Supplying, fitting and fixing UPVC pipes A-type and fittings conforming to IS : 13592-1992 with all necessary clamps, nails, including making holes in wall, floor etc. cutting trenches in any soil, thorough masonry concrete structure etc. . UPVC pipes. i) 110 mm. dia

A)UPVC pipes-110mm.dia

B)plain tee-110mm. Dia

C)plain y-110. dia

D)bend 87.5 degree-110mm. Dia

E)shoe-110mm. Dia

Supplying, fitting and fixing flat back urinal in white vitreous china ware of approved make in position with brass screws on 75 x 75 x 75 mm. wooden blocks complete. 470 x 280 x 340 mm.

Supplying, fitting and fixing Anglo-Indian W.C. in white glazed vitreous china ware of approved make complete in position with necessary bolts, nuts etc.(b) With 'S' trap (with vent)

Supplying, fitting and fixing 10 liter PVC low down cistern conforming to I.S. specification with PVC fittings complete C.I. brackets including two coats of painting to bracket etc.

Supplying, fitting and fixing approved brand 32 mm. dia PVC waste pipe, with PVC coupling at one end fitted with necessary clamps.900 mm. long.

Supplying, fitting and fixing approved brand 32 mm. dia PVC waste pipe, with PVC coupling at one end fitted with necessary clamps.750 mm. long.

Supplying, fitting and fixing approved brand PVC connector white flexible with both end coupling with heavy brass CP nut 15 mm. Dia . 450 mm. long.

Supplying, fitting and fixing white china best quality of approved make wash basin with C.I. brackets on 75 x 75 mm wooden blocks C.P.waste fittings of 32 mm. dia one of approved quality brass C.P. pillar cock of 15mm. ………..including mending good all damages and painting the brackets with two coats of approved paints. 550 x 400 mm. size.

Supplying, fitting and fixing best quality Indian make mirror 5.5 mm. thick with silvering approved quality as per I.S.I. specification supported on fiber glass freme of any colour frame size 600 x 450 mm. complete in all respect as per direction of engineer-in-charge.

Glass shelves with aluminium guard rails size 600 x 125 mm. with 505 mm. thick glass.

Supplying, fitting and fixing porcelin soap tray of approved make. (i) Recessed soap tray of size 150 mm. X 150 mm.

Supplying, fitting and fixing allumium approved brand towel rail 25 mm. dia 450 mm. long with two brackets complete all respect as per direction of engineer-in-charge.

b)Supplying, fitting and fixing of following specials with valamoid joints including sealing the top with cement mortar (4:1) i) Cast iron single branch 100 mm. dia.

ii) H.C.I bend with door 100 mm. dia.

iii) H.C.I heal rest bend 100 mm. dia

Supplying, fitting and fixing cast iron ‘P’ or ‘S’ trap conforming to IS 3989/1970 and 1729/1964 including lead caulked joints sand painting two coats to the exposed surface. 100 mm. ‘P’ trap.

Supplying, fitting and fixing C.P. stop / bib cock.i) Chromium plated bib cock short body.

ii)Chromium plated stop cock

Supplying, fitting and fixing pillar cock of approved make. a) (i) CP Pillar C

ock - 15 mm. (Equivalent to Code No. 507 & Model - Tropical / Sumthing Special of ESSCO or similar brand).

Supplying, fitting and fixing peets valve full way gun metal standard pattern best quality of approved brand with fittings. i) 25 mm.

Supplying, fitting and fixing shower of approved brand and make.Chromium plated round shower with revolving joint.

18 mm. thick marble partition slab with chawk doongri marble square cut, both side polished with two front corners rounded and edges polished fitted and fixed complete.

Supplying, fitting and fixing 1st quality ceramic tiles in walls and floors to match with the existing work and 4 nos of key stones(10mm.) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc . with sand cement mortar (1:4) 20 20mm thick 2 mm thick cement slurry at back side of tiles using cement @ 2.91 kg/sqm & joint filling using white cement slurry @ .20 kg/sqm area of each tile upto 0.09 sqm coloured decorative (wall)

Supplying, fitting and fixing 100 mm. C.I. round gratings (heavy type)

Supplying, fitting and fixing pedestal of approved make for wash basin (white)

Supplying, profiles of required section made of aluminum alloy extrusive confirming to I.S. 733-1983 and I.S. 1285-1975 anodised film thickness and specification colour/natural) matt finished confirming I.S. 1868-1983 for fabrication of composite door, sliding & casement windows, partitios, formed of basic sections of any ISI embossed/certified make and brand as per direction of Engineer-in -charge (payment will be made on finished length of the work). A) 15 micron colour Anodizing (i) a) 2- track sliding window i) Bottom frame Coloured.

Supplying, fitting and fixing pedestal of approved make for wash basin (white)

ii) Top and side frame.

b) 3- track sliding window i) Bottom frame

c) Shutter for all track sliding window. i) Bottom & Top member.

c) Shutter for all track sliding window. ii) Style side member.

c) Shutter for all track sliding window. iii) Interlock member.

Supplying PVC rollers for sliding windows as per direction of Engineer in charge.

Supplying maruti lock (100mm)

Supplying bubble free float glass of approved make and brand. Conforming to IS:2835-1987 5mm thick clear glass .

6mm thick clear glass.

Supplying concealed type heavy duty hydraulic double action floor spring along with top / pin set of pivots conforming to IS: 6315 or any approved make as per direction of Engineer in charge..

Supplying concealed type PVC headed aluminum tower bolt for double leaf doors as per approved make. 300 mm long

Supplying ‘U’ shaped EPDM gasket of approved make and brand and brand as per direction of EIC.

Supplying T' shaped EPDM gasket of approved make and brand as per direction of EIC.

weather gasket / wool pile for door vertical

Labour charges for fabrication and installation of composite door window, partition made from anodized extended alloy aluminum sections. For the following units:- fully glazed single leaf reamless swing door made of anodised aluminium alloy extrusions fabrication after cutting to proper shape and size, drilling and aligning fitted with heavy duty hydrolic action floor spring with top pin assembly and fitted with inbuilt locking arrangement and all other necessary fittings, fixture, adhesives and joineries, cutting the glass to requisite shape and size mounting the edges for fitting the same with dry set neoprine / EPDM gasket

Supplying profiles of required section made of Aluminium Alloy Extrusions conforming to IS: 732-1983 and IS: 1285- 1975; Annodized (with required film thickness and specified colour / natural) matt finished conforming to IS: 1868-1983 for fabrication of composit door, sliding & casement windows, partitions, formed of basic sections of any ISI embossed / certified make and brand as per direction of Engineer - InCharge. (Payment will be made on finished length of the work)(A) In 10-12 Micron thickness Annodizing film.Movable door shutteri) Door frame. (Top & sides).

ii) Shutter : Top rail.

iii) Shutter:Bottom rail.

iv) Shutter:Lock rail

v)Door vertical.

vi)Glazing cleap

Labour charge for fabrication and installation of composite door, window, partitions made from annodized extruded alloy aluminium sections for the following units.Partly glazed partly panelled or fully glazed single leaf alunminium swing door made of extruded and annodized alloy aluminium sections, fabrication including cutting to proper shape and size, drilling and aligning, fitted with heavy duty hydraulic action floor sping placed in the floor with mending damages,with top pin assembly of approve make and brand, fitted with in built locking arrangement, flush bolt, glazing clips and all other necessary fittings, fixtures, adhesives and joineries, cutting glass of approved make to requisite shape and size fitting with dry set neoprene or EPDM gasketing, cutting to requisite shape and size panel board (prelaminated particle block) fixing them with glazing clips as per drawing, specification and direction of Engineer in charge.

Partly glazed and partly panelled partition or fixed glazing made of extruded and anodised alloy aluminium sections, fabrications after cutting to proper shape and size, drilling and aligning fitted with inbuilt locking arrangement cutting the glass / board (prelaminated / particle / block) to requisite shape and size moulding the edges fitted and fixed glazing clips and dry set neoprine /EPDM gasket, along with all other necessary arrangements for fixing the partition to walls, floors, beams, columns polysulphide sealant for water proofing if necessary complete in all respect as per drawing and specifications and direction of the Engineer in charge.for partition using section of size:63.50 mmx 38.10 mm

Applying exterior grade acrylic primer of approved quality and brand on plastered or concrete surface old or new surface to receive decorative textured ( matt finish ) or smooth finish acrylic exterior emulsion paint including scraping and preparation the surface thoroughly complete as per manufacturer`s specification and as per direction of the EIC. G.Fl.

Protective and decorative acrylic exterior emulsion paint of approved quality as per manufacturer`s specification and as per direction of EIC to be applied over acrylic primer as required. the rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer (G.Fl 2 coats) normal acrylic emulsionprimer 100% acrylic exterior emulsion paint of approved quality as per manufacturer’s specification. i)In ground floor

Rendering the Surface of walls and ceiling with White Cement base WATER PROOF wall putty of approved make & brand.(1.5 mm thick).

Applying interior grade acrylic primer of approved quality and surface old or new surface to receive distemper / acrylic emulsion paint including scraping and preparing the surface thoroughly. Water based interior grade

acrylic primer.

Applying acrylic emulsion paint of approved make and brand on walls and ceiling including sand papering in intermediate coats including putty (two coats) Luxury quality

18 mm. to 22 mm. thick, kota stone slab set in 20 mm thick (avg) cement mortar (1:4) in floor, stair & lobby including pointing in cement slurry with admixture of pigment matching the stone shade, including grinding & polishing as per direction of Engineer - in -charge to match with the existing work. [Slurry for bedding @ 4.4 kg/Sq.m and pointing @2.0 kg/Sq.m]

Supplying and laying Polythene Sheet (150gm / sq.m.) over damp proof course or below flooring or roof terracing or in foundation or in foundation trenches.

Dismantling all types of masonry excepting cement concrete plain or reinforced. Stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m. (a) In ground floor including roof.

Dismantling all types of plain cement concrete works, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m. In groung floor including roof. (a) upto 150 mm. thick .

Dismantling R.C. floor, roof, beams etc. including cutting rods and removing rubbish as directed within a lead of 75 m. including stacking of steel bars. (a) In ground floor including roof.

Cleaning compound premises of shrubs,plants,jungles etc by cutting and removing as directed(specific permission of Engineer-in-Charge prior to execution will be necessary)(payment to be made on area cleared)

Supplying, fitting and fixing CPVC (Chlorinated Polyvinyl Chloride) pipes of approved make conforming to IS-15778: 2007 . with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. (a) For Exposed Work CPVC Pipes Class-1, SDR-11 1. 15 mm dia.

2. 20 mm dia.

Dismantling R.C. floor, roof, beams etc. including cutting rods and removing rubbish as directed within a lead of 75 m. including stacking of steel bars. (a) In ground floor including roof.

Cleaning compound premises of shrubs,plants,jungles etc by cutting and removing as directed(specific permission of Engineer-in-Charge prior to execution will be necessary)(payment to be made on area cleared)

3. 25 mm dia.

4. 40 mm dia.

(b) For Concealed Work CPVC Pipes Class-1, SDR-11 1. 15 mm dia.

Reducing Socket 200 mm X 250 mm

Supplying, fitting and fixing of steel cutter piece up to 450 mm long with sockets .75 mm dia.

Supplying, fitting and fixing plug of approved make conforming to I.S. specifications.75mm dia