Renovation Addition and alteration of Existing bath house inside the swimming pool at IITM and Converting the existing men changing room into womens changing and shower room at ground floor and Construction of additional floor over the existing

Amount

Schedule -A -Civil Works

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. - In cement mortar

Dismantling tile work / Cement concrete flooring in floors/roofs/Skirting laid in cement mortar including stacking material within 50 metres lead. - For thickness up to 40 mm

Demolishing brick tile covering in terracing including stacking of serviceable material and disposal of unserviceable material within 50 metres lead.

Demolishing mud phaska in terracing and disposal of material within 50 metres lead.

Demolishing R.C.C. work by mechanical means and stockpiling at designated locations and disposal of dismantled materials up to a lead of 1 kilometre, stacking serviceable and unserviceable material separately including cutting reinforcement bars

Disposal of all building rubbish/malba/similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved corporation dumping ground outside IIT Madras campus or as approved by Engineer-in charge, beyond 50m initial lead, for all leads including all lifts involved. Contractor shall remove all debris generated during construction/ renovation work

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - 1:3:6 (1 Cement : 3 M Sand : 6 graded stone aggregate 20 mm nominal size)

Providing and fixing stainless steel ( Grade 304) railing / gate / frames made of Hollow tubes, channels, plates, hinges etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge. Bolting arrangement for fixing SS hand rail shall be as per the drawing enclosed. (for payment purpose only weight of stainless steel members shall be considered. No additional payment will be made for bolting arrangements, fixing accessories such as nuts, bolts, fasteners etc.)

Providing and laying in position ready mixed plain cement concrete, All works above plinth and upto floor V level. with cement content as per approved design mix and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for plain cement concrete work, including pumping of R.M.C. from transit mixer to site of laying and curing, excluding the cost of centering, shuttering and finishing, including cost of curing, admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. M-10 grade plain cement concrete (cement content considered @ 220 kg/cum).

Half brick masonry with fly ash concrete blocks of class designation 100, in super structure above plinth and upto floor V level. Cement mortar 1 : 4 (1 cement : 4 coarse sand)

Extra for providing and placing in position 2 Nos 8mm dia. TMT bars at every third course of half brick masonry.

Providing and fixing 18mm thick gang saw cut mirror polished (premoulded and prepolished) machine cut for flooring , kitchen platforms, vanity counters ,window sills , facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing moulding and polishing to edge to give high gloss finish etc. complete at all levels. Granite of any colour and shade Area of slab over 0.50 Sqm.

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. With cement mortar 1:4 (1 cement : 4 fine sand)

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location in marble/Granite/stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete.

Providing and fixing stone slab table rubbed, edges rounded and polished of size 75x50 cm deep and 1.8 cm thick fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. Granite Stone of approved shade.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash Fastener shall be paid for separately) : Second class teak wood

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters : 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of shutters (over all area of door shutter to be measured)

Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured).

Providing and fixing IS:12817 marked Stainless steel butt hinges (heavy weight) with Stainless steel screws etc., complete. 125x64x2.5mm

Providing and fixing aluminium sliding door bolts, ISI marked anodised (Anodic coating not less that grade AC 10 as per IS1868) transparent of dyed to required colour of shade, with nuts and screws etc., complete 250x16mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (Anodic coating not less that grade AC 10 as per IS1868) transparent of dyed to required colour of shade, with necessary screws etc., complete 200x10mm

Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 100 mm

Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. Single rubber stopper

Providing and fixing aluminium tee channels for sliding doors (Heavy duty), anodised (Anodic coating not less that grade AC 10 as per IS1868) transparent of dyed to required colour of shade, with rollers & stop end necessary screws etc., complete

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Anchor & connection bolts included Hot finished welded type tubes.

Applying priming coat with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel works ( 2 Coats)

Finishing with Epoxy Paint (2 or more coats ) at all locations prepared and applied as per manufacturers specifications including appropriate priming coat , preparation of surface etc on steel works

Providing and fixing 1st quality Ceramic glazed wall tiles (thickness to be specified by the manufacturer) conforming to IS : 15622 of all colours and shades except burgundy, bottlegreen and black of any size as approved by engineer in charge , in skirting, steps risers and dadooing laid on 12 mm thick cement mortar 1:3 (1 Cement : 3 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.

Cement bonded particle baord / Calcium silicate board partition of thickness 100mm thick Supplying and fixing of bison panel boards of 10mm thick panel of size 8' x4' as approved by Architect/ Engineer -in charge, fixed over G.I stud framework of required size or frame with aluminum sections 100x40 x2mm sections’ studs @ 610mm Vertical x 1200mm Horizontal spacing . The gap between the boards shall be filled with 100mm thick SoundSynth AW wool. The tiles are to be fixed to Aluminium frame using seam fasteners etc. The surface should be finished with 1mm thick mica of appropriate shade or acrylic interior paint by using necessary adhesive, nails etc complete as directed by Engineer in charge. (deduction towards opening will be made for the measurement)

Supplying and erecting Installation of fabric structure as per the approved design and the structure to be designed, fabricated and installed as per relevant Indian Standard norms. The canopy / fabric structure shall be designed for as per the wind speed prevalent in that area as per I.S. 875-Part 3. The steel structure shall be designed as per I.S. 800. The steel fabrication and erection shall be as per I.S. norms. The membrane will be 850GSM block out PVC Coated Fabric of make Ferrari or Equivalent. The above fabric will be patterned, and welded with the high frequency welding machine and at the end pockets will be made to slide the Kedar profile and will be fixed using a special aluminum extrusions at the end of the roof truss. The rate quoted for the structure should be on area covered by canopy and the rate inclusive of design, preparation of detailed drawing, approval from IITM, supply and installation of canopy as per the approved design etc. complete. The rate inclusive of providing necessary anchor fastener for fixing the trusses to the existing building and foundation bolts etc., complete.

Supply and installation of125 x 125 mm SS floor grating. Suggested model: Neco/Neer/Chilli or equivalent

Providing and fixing wash basin (counter top ) Oval type wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with single of 15 mm C.P. brass pillar taps

Providing and fixing unplasticised PVC connection pipe with brass unions : 45 cm length and 15 mm nominal bore

Providing and fixing PVC waste pipe for sink or wash basin including PVC waste fittings complete. Flexible pipe 40mm dia

Providing and fixing PTMT grating of approved quality and colour Circular type 125 mm nominal dia with 25 mm waste hole

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Internal work. Concealed work, including cutting chases and making good the walls etc. 20 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work : 40mm nominal dia Pipes

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge.

Labour charges for dismantling and removing the existing water closet including debris cleaning up to lead of 50m lead.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

Providing and fixing brass stop cock of approved quality : 20 mm nominal bore

Providing and fixing brass bib cock of approved quality : 20 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

25 mm nominal bore

40 mm nominal bore

Supply and installation of PARRY WARE LAVATORY WITH BRACKET , ITEM CODE LW814CJW/F#W, HS CODE 69101000, NSize - 750W x 480D x150mm) complete with auto faucet, sensorcontroller, pipe to wall, escutcheon plate and rubber adaptor for waste connection

Providing and fixing of mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6mm thick hard board backing. Rectangular shape 1500x450 mm

Providing and fixing PTMT Soap dish holder having length of 138mm breadth 102mm, height of 75mm concealed fitting arrangements, weighing not less than 106 gms.

Supplying and fixing PTMT Health faucet - 15mm dia of Prayag or equivalent make as approved by the Engineer-in-charge (Prayag Cat No.187 with a Base price of Rs.309 or Equivalent)

Providing and fixing SWR PVC heavy duty nahini trap of size 110mm X 75mm (Finolex/ Prince) complete as approved by Engineer -in-charge

Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with bracket of the same materilas with snap fittings of approved quality and colour, weighing not less than 105 gms.Soap dish holder having length of 138mm breadth 102mm, height of 75mm concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing hand drier of CAMRY make with single blower, with time delay, summer & winter control, music while drying, volume ON/ OFF controls including providing necessary brackets, cable from drier to Plug, Plug top key and lock etc, complete as required.

Providing and fixing SS hangers in changing rooms and the hangers shall have minimum 6 hooks. The rate quote shall include the cost of the materials, labours, tools etc and complete as per the direction of the engineer incharge

Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar bent to shape with hooked ends in R.C.C. slabs, beams during laying including painting the exposed portion of loop, all as per standard design complete.

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp of internal dia 140mm, 73mm height, top lid of 1.5mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3mm dia. round headed screws, one lock at the corners. Clamp shall be made of 12mm dia M.S. bar bent to shape as per standard drawing.

Providing and fixing factory made uPVC white colour fixed glazed windows/ventilators comprising of uPVC multi-chambered frame and mullion(where ever required) extruded profiles duly reinforced with 1.60 ± 0.2mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plasticpackers, plastic caps and necessary stainless steel screws etc. Profileof frame shall be mitred cut and fusion welded at all corners, mullion (ifrequired) shall be also fusion welded including drilling of holes for fixinghardware's and drainage of water etc.After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. Fixed window /ventilator without mullion / transom .Using R2 series with frame (39mm & above) X(39mm & above).Height upto 1.2 metre

Two or more coats : Enamel painting for doors / windows / steel works / wall panels (two or more coats including primer) on both exterior and interior surface of wooden and steel joineries using approved colour, make and brand of synthetic enamel paint two or more coats. The contractor should ensure complete covering of floors using tarpaulin / plastic sheet while taking up the work. The work shall be executed as per the detailed specifications and special conditions. The rate quoted shall be inclusive of charges towards all labour, material, transport, scaffolding, safety arrangements, Personal Protective Equipments (PPE), tools and plants etc.

Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after .The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineerin- charge .The elevational area of the scaffolding shall be measured for payment purpose .The payment will be made once irrespective of duration of scaffolding.

Providing and fixing precoated colour or mill finish aluminium roofing accessories in 0.71mm thichness, Alloy 31500 (IS designation) (Aluminium Alloy (AA) 3004 (ISO Designation)) for colour coating shall be 5-7 microns epoxy primer on both sides of the sheet and polyester top coat 15-18 microns, using self drilling / tapping SS screws of size 6x50mm with 3mm thick EPDM seal and SS plain washer complete :

Precoated mill finish aluminium gutter (600 mm over all girth )

Precoated mill finish aluminium Ridges (500-600 mm)

Precoated mill finish aluminium flashings /Aprons (upto 600 mm)

Cement bonded particle board 8mm thick (Fire, termite & moisture resisitance) as per IS:14276:1995

Providing and applying white cement based putty of average thickness upto 1mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting with two coats premium acrylic emulsion paint of interior grade having VOC content less than 50gms/litre of approved brand and manufacture including applying additional coats wherever required to achieve even shade and colour : Applying priming coats with primer of approved brand and manufacture having low VOC content : with water thinnable cement primer on wall surface having VOC content less than 50 gms/litre .

Providing and Fixing factory made PVC door frame made of PVC extruded sections of size 75 mm x 53 mm, having wall thickness 2.0 mm (± 0.2 mm). Both verticalssides of the frame reinforced with PVC profile of cross section size 28 mm x 30 mm x 2 mm thickness (± 0.2 mm) and 75 mm x 200 mm long, including reinforcing both ends of the top frame with PVC profile. PVC Door Frame and PVC reinforcement profile to be mitred cut, jointed and fusion welded together, including providing and fixing 3 nos of 125 mm long stainless steel hinges to frame, fixing the frame with jamb with required nos & sizes of anchor dash fastener, all complete as per manufacturer's specification and direction of Engineer-in-charge..

Providing and fixing 37 mm thick factory made PVC Door shutter, styles and rails made of PVC hollow extruded printed and laminated section having overall dimension 115 mm x 37 mm with wall thickness 2 mm (± 0.2 mm) with inbuilt beading on one side, the styles and rails mitred cut and joint at corners by inserting 2 nos PVC profile reinforcement of size 75 mm x 200 mm long with cross section size of 28 mm x 30 mm having wall thickness 2 mm (± 0.2 mm). Styles, rails and reinforcements to be fusion welded together. Only hinge side vertical style to be reinforced with PVC profile reinforcement in full length. Printed and laminated PVC lock rail of size 110 mm x 37 mm having wall thickness 2 mm (± 0.2 mm) to be welded horizontally with the vertical styles after inserting PVC profile reinforcement as in styles and rails, providing with PVC snap fit beading, panels of 100 x 20 mm printed & laminated and inserting 2 nos 6 mm dia bright steel rod horizontally with both side threaded and tightened with check nuts and washers complete, all as per manufacturer's specification and direction of engineer-in-charge.

Providing and d Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.

TECHNICAL SPECIFICATION / WORK METHODOLOGY FOR WATERPROOFING OF SUNKEN PORTIONS 1. The BrickWall-Floor junctions and other construction joints to be cut open to a V-groove of size 25mm X 50mm and reinstated with BASF make - Rheomix 141 - SBR Polymeric modified Cement mortar (CM 1:4) at a dosage of 2 ltrs per cement bag. 2. Necessary pipe chasings and outlets to be ear-marked and completed well before starting our waterproofing treatment. 3. The Floor and wall surfaces to be cleaned thoroughly without any traces of dirt or laitanace and applied with two coats of Masterseal 550 – two part acrylic modified cementitious polymer membrane coating to a thickness of 1mm, over the above prepared wall and floor surface as per the mixing, application and coverage recommendations of the manufacturer. 4. The above coated floor and wall surface to be overlaid with a protective plastering in CM 1:4, 20mm thick, admixed with BASF make Rheomac 707 – Integral waterproofing compound @ 150ml per Cement bag. 5. The Pipe outlet area to be provided with water-tight shuttering and filled with Non-shrink grout BASF make - Masterflow 918 as per the application procedures recommended by the manufacturer.

Exterior cladding: Supplying and fixing of PU PANEL 50 comprising of profiled sheet made out of 0.5 mm TCT 300 Mpa 150 GSM colour coated Galvalume sheet on the top and 0.5 mm TCT colour 300 Mpa colour coated Galvalume sheet with slightly ribbed sheet at the bottom. In between 50 mm thick CFC/ HCFC free Polyurethane Foam Insulation at a density of 40 +/-2 kg/cum. as core shall be injected by special foaming machine. The panels are joined together by tongue and groove method and placed in the vertical direction. (Quotations attached) - Color: Sky blue/Off white/Mist green/Autumn red.

Roofing - Supplying and fixing of PU PANEL 50 comprising of profiled sheet made out of 0.5 mm TCT 300 Mpa 150 GSM colour coated Galvalume sheet on the top and 0.5 mm TCT colour 300 Mpa colour coated Galvalume sheet with slightly ribbed sheet at the bottom. In between 50 mm thick CFC/ HCFC free Polyurethane Foam Insulation at a density of 40 +/-2 kg/cum. as core shall be injected by special foaming machine. The panels are joined together by tongue and groove method and placed in the vertical direction. Colour: Sky blue/Off white/Mist green/Autumn red.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work : 40mm nominal dia Pipes metre 221.35

Providing and fixing brass bib cock of approved quality : 15 mm nominal bore

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : Single half stall urinal with 5 litre P.V.C. automatic flushing cistern

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 150 mm diameter

Providing and fixing brass bib cock of approved quality : 20 mm nominal bore

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, Single socketed pipes. 110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings / accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Single tee with door 110x110x110 mm

Bend 110mm

Shoe 110mm

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 150 x 100 mm size P type with flyash concrete blocks of grade M10

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 25mm dia

Schedule -B Electrical Works

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

3½ X 50 sq. mm (35mm)

Supplying of following sizes one number PVC insulated and PVC sheathed / XLPE armoured power cable of 1.1 KV grade conforming to relevant IS standards.

3½ x 50sq.mm Al Arm. Cable

Supplying and fixing FP sheet steel enclosure on surface/ recess along with 63A 415 V "C" curve FP MCB complete with connections, testing and commissioning etc. as required.

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.

Above 35 sq. mm and upt 95 sq.mm (clamped with 25 x 3 mm MS flat clamp)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.

Above 35 sq. mm and upt 95 sq.mm

Supplying and fixing following ways surface/ recess mounting, vertical type, 415V, TPN MCB distribution board of sheet steel, dust protected, powder painted, inclusive of 200A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incommer) as required (Note: Vertical type MCB TPDB is normally used where 3 phase outlets are required).

8 way (4 + 24) , Double door.

Providing and fixing Four pole MCCB with thermomagnetic release and terminal spreaders in existing cubice panel board including drilling holes in cubicle panel, making connections , etc,. as required

125A , 16KA, TPMCCB

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Supplying and fixing following way, horizontal type triple pole and neutral, sheet steel, MCB distribution board, 415 Volts, on surface/ recess, complete with tinned copper busbar, earth bar, din bar, interconnections, powder painted including earthing etc. as required testing and commissioning etc.as required.

6 way (4 + 18) , Double door.

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single pole MCB

Supplying and fixing 40 amps to 63 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Triple pole MCB

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required.

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

Wiring for light point / fan point / exhaust fan point / call bell point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit ,with modular switch, modular plate,suitable G.I.Box and earthing the point with 1.5 sq mm PVC insulated FR copper conductor single core cable etc as required. Group " C "

Wiring for circuit / sub main wiring along with earth wire with the following sizes of PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit etc as required.

2 x 1.5 sq.mm + 1 x 1.5 sq.mm earth wire

2 x 2.5 sq.mm + 1 x 2.5 sq.mm earth wire

2 x 4 sq.mm + 1 x 4 sq.mm earth wire

2 x 6 sq.mm + 1 x 6 sq.mm earth wire

4 x 6 sq.mm + 2 x 6 sq.mm earth wire

4 x 10 sq.mm + 2 x 6 sq.mm earth wire

Supplying and fixing following sizes of medium class PVC conduit along with the accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing of suitable size GI/ Surface box with modular plate and cover in front on surface or in recess, i/c pdg. and fixing 1 No 3 pin 6 amps modular socket outlet and 1 No 6 amps modular type switch, connections, earthing, etc as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required.(For light plugs to be used in non residential building)

Supplying and fixing following modular switch/socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

5/6A Switch

15/16A Switch

3 pin 5/6A socket outlet

6 pin 5/6A socket outlet

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following modular base & cover plate on existing modular metal boxes etc. as required.

1 or 2 module

3 Module

4 Module

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min, 350 RPM (tolerance as per IS: 374-2019), THD less than 10%,compatible electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Supplying, installing, testing and commissioning of BLDC ceiling fan, including wiring the down rods of length up to 45 cm with 1.5 sq mm FRLS PVC insulated, copper conductor, single core cable etc as required. 900 mm sweep ceiling fan.

Supplying and installing following size of perforated hot dipped galvanised iron cable tray (galvanised thk not less than 50 microns) with perforation not more than 17.5% in convinient sections joined with connectors suspended from ceiling with GI suspenders including GI bolts & nuts etc are required: 300 mm width x 50 mm depth x 1.6mm thk

Supplying and fixing of wall or ceiling mounted type Fixed Dome or Bullet type Camera 2.0 Megapixel high-performance CMOS, Analog HD output, up to 1080P resolution True Day/Night, DNR, Smart IR Up to 30m IR distance, IP66 weatherproof with all necessary BNC connectors and fixing accessories as required.

Supply and fixing of 8 PoE Switches for CCTV IP Camera on suitable zinc-passivated box complete with metal / Pvc box, front plate, screws and fixing accessories etc.

Supplying and installing of 8 Channel Network Video Recorder with Max 320Mbps incoming bandwidth Smart H.265+/H.265/ Smart H.264+/H.264/MJPEG Up to 12MP resolution preview and playback Support 8 SATA HDDs up to 10TB Each, 4 USB (2 USB3.0, 2USB2.0) 2 HDMI / 2 VGA simultaneous video output Support Multi-brand network cameras Support RAID 0/1/5/10 Mobile Software: iCMOB, gCMOB CMS Software: KVMS Pro. The items including supply of 4TB hard disk, connectors, pins and providing complete configuration etc.

Supplying and installing of Power Supply Unit along with necessary Battery backup, suitable for 1 nos. 8 channel network video recorder system.

Supplying and installing of 32" LED colour monitor and fixing accessories.

Supplying and drawing following of UTP 4 pair CAT 6 LAN Cable in existing surface / recessed steel/ PVC conduit as required. 1 run of cable

Supply and Installation of Exhaust fan in the existing open, including making good the damage, connection, testing and comissioning etc. as required

300mm sweep medium duty exhaust fan

Supply & Installation of 1200mm x 21w LED light fittings. The approved make will be PHILIPS LED BN021LED25S 6500 PSU GR S1 or equivalent as per Engineer Incharge

Supplying and fixing of 18W LED 6500K Surface/Recess mounted ceiling Fitting. (Philips Full glow rimless or equivalent as approved by Engineer Incharge)

Supplying and fixing of 6W LED 300K outdoor Burried light type Fitting. (Philips - BBP341 LED540 or equivalent as per Engineer Incharge)

Supply, Installation, testing and commissioning of 500 LPD Non Pressurized storage water tank alongwith 2 Nos of 2000w backup immersion heater with FPC Solar water heater panels as per the attached specifications in the terrace of the swimming pool. All the accessories required for the same are under the scope of the contractor. Make : Solar Hitech /Anu Solar/Racold/V Guard or equivalent as per Engineer Incharge

M/S. NAVEEN CONSTRUCTIONS (BID ID -756154)

CREATORS ENGINEERS AND INTERIORS PVT LTD (BID ID -756025)