Renovation Repair of Bathroom in Madhav Hostel at Dr YSP University of Horticulture and forestry nauni solan

Amount

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering work up to plinth level with 1:5:10 (one cement : five sand : ten graded stone aggregate 40 mm (forty milimetre) nominal size etc. complete in all respect as per satisfaction of Engineer-in-charge

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete in all levels etc. complete in all respect as per satisfaction of Engineer-in-Charge. a). Granite of any colour and shade Area of slab upto 0.50 sqm

Providing and fixing 100x58x1.90 mm ISI marked oxidised M.S. pressed butt hinges with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Providing and fixing ISI marked oxidized/ Chromium plated M.S. Sliding door bolts with nuts and screws etc. complete in all respect as per satisfaction of Engineer-in-Charge a). 250x16 mm ( Two hundred fifty into sixteen milimetre)

Providing and fixing ISI marked oxidized// Chromium plated M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-Charge

a). 200x10 mm( Two hundred into ten milimetre)

b). 150x10 mm( One hundred fifty into ten milimetre)

Providing and fixing ISI marked oxidized/ chromium plated M.S. handles conforming to IS:4992 with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-Charge

a). 125mm (one hundred twenty five milimetre)

b). 100mm (one hundred milimetre)

Providing and fixing ISI marked 85x42 mm oxidized M.S. pull bolt lock conforming to IS: 7534 with necessary screws bolts, nut and washers etc. complete. in all respect as per satisfaction of Engineer-in-Charge.

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-charge. a) Single rubber stopper.

Providing and fixing aluminum U beading of required size to Pre-laminated/ flush door shutter, including fixing etc. complete as per direction of Engineer-in-charge.

Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws andapplying a priming coat of approved steel primer, all complete as per the directionof Engineer-In-charge

Providing and laying rectified jointless Ceramic floor tiles (Kazaria / Oreint bell / Nitco/ Somany make) of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (one Cement : four sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc complete in all respect as per satisfaction of Engineer-in-Charge

Grouting the joints of flooring Kota/tiles 300 into 300mm size having joints of 3 mm width in different size of tiles/ Kota stone, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing etc. complete as per the satisfaction of Engineer-in-charge.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade etc. complete in all respect as per satisfaction of Engineer-in-Charge. a) Two or more coats on new work.

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer’s specification etc. complete in all respect as per satisfaction of Engineer-in-Charge.. a). one or more coats on Old work.

Demolishing cement concrete manually/ by mechanical means including disposal of material within all leads etc. complete as per direction of Engineer - in – charge. a). Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix).

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within all leads etc. all complete as specified and as directed by the Engineer-in-Charge a). For thickness of tiles 10mm to 25mm

Taking out doors, windows and clerestory window shutters (wood or steel) including stacking in all leads etc. in all respect as per satisfaction of Engineer-in-Charge a) Of area 3 square metre and below.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm PVC P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required complete in all respect as per satisfaction of Engineer-in-Charge (Cera / Hindware make). a) White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests.

Providing and fixing 600x450mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Providing and fixing 32mm dia Semi rigid pipe P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete in all respect as per satisfaction of Engineer-in-Charge..

Providing and fixing 45 cm length and 15 mm nominal dia uplasticised PVC connection pipe with brass unions complete in all respect as per satisfaction of Engineer-in-Charge.

Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 complete in all respect as per satisfaction of Engineer-in-Charge Seiko/ smile/ sparton/ zar make).

Providing and fixing 15 mm nominal bore C.P. brass long body bib cock of approved quality conforming to IS:8931 complete in all respect as per satisfaction of Engineer-in-Charge (Seiko/ smile/ sparton/ zar make).

Providing and fixing 20 mm (twenty milimetre) nominal bore gun metal gate valve with C.I. wheel of approved quality (screwed end) etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Cutting holes up to 30x30 cm in walls including making good the same with common burnt clay F.P.S. (non modular) bricks complete in all respect as per satisfaction of Engineer-in-Charge.

Providing and fixing vitreous china wash basin with single hole forpillar tap with C.I. or M.S. bracts painted white including cuttingholes and making good the same but excluding fittings complete in all respect as per satisfaction of Engineer-in-charge Cera / Hindware make. a) 560x400mm (Oval type) counter top

Providing and fixing 100mm dia chromium plated grating of superior quality for floor, gully or nahani trap complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete in all respect as per satisfaction of Engineer-in-charge (Filolex / Kisan / D-Plast make).a) 110mmx75mm

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Vectus/D-plast/Prayag make).

a). 75mm (Seventy five millimetre) dia

b).. 110mm (One hundred ten millimetre) dia

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Vectus/D-plast/Prayag make).

a). 75mm (Seventy five millimetre) dia

b).. 110mm (One hundred ten millimetre) dia

Providing and fixing PVC plain bend ISI marked complete including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Vectus/D-plast/Prayag make).

a). 75mm (Seventy five millimetre) dia

b).. 110mm (One hundred ten millimetre) dia

Providing and fixing PVC door bend with oval access door, insertion rubber washer 3mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Vectus/D-plast/ Prayag make).

a). 75mm (Seventy five millimetre) dia

b).. 110mm (One hundred ten millimetre) dia

Providing and fixing PVC single equal branch with oval access door, ISI marked insertion rubber washer 3mm thick bolts and nuts complete including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in charge (Finolex/Vectus/D-plast/Prayag make).

a). 75mm (Seventy five millimetre) dia

b).. 110mm (One hundred ten millimetre) dia

Providing and fixing PVC clamps ISI marked of approved design with steel screws and rawl plugs etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Kisan/D-plast make).

a). 75mm (Seventy five millimetre) dia

b).. 110mm (One hundred ten millimetre) dia

Providing and fixing PVC Cowl ISI marked including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Kisan/D-plast make).

a). 75mm (Seventy five millimetre) dia

b).. 110mm (One hundred ten millimetre) dia

Providing and fixing 25 mm (Twenty five milimetre) thick factory made shutters of Pre-laminated HDHMR (High Density High Moisture Resistancee) board both side decorative finish conforming to IS: 12406 Grade of approved design, including fixing of heavy MS hinges 4” long etc. complete as per architectural drawing and direction of Engineer-in-Charge. (Cost of hinges will be paid for separately).

PREM KRISHAN (BID ID -557215)