PROVN OF SEWAGE SYSTEM AND WATER TANK AND ADDN/ ALTN KITCHEN IN BLDG NO RB-69, 70, 71 AT MES COLONY AND STATIC WKSP EME AND TWO BATHROOM AT BLDG NO 380 UNDER GE (MCTE) MHOW

Amount

Item No.1 Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in any type of soil surfaces formed to required slope, gradient, camber, and superelevation etc. complete all as specified.

Item No.2 Excavating in trenches, not exceeding 1.5 m wide but not exceeding 1.5 m in depth; for foundations etc. or for shafts, well cess pits, manholes, pier holes, etc. not exceeding 10 qm on plan but not exceeding 1.5 m in depth and getting out in any type of soil complete all as specified.

Item No.3 Removing excavated material (soil) exceeding 250 m and not exceeding 500 m and depositing where directed at a level not exceeding 1.5 m above the starting point all as specified

Item No.4 Dismantling Brickwork or stone boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc. but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified

Item No.5 Returning, filling in, including spreading, levelling, watering and well ramming in layer not exceeding 25 cm thick in any type of soil complete all as specified.

Item No.6 M&L for plain cement concrete 1:4:8 type D2 using 40mm graded stone aggregate as in sub base of floor, complete all as specified.

Item No.7 M&L for Plain Cement concrete 1:5:10 type E2 in foundations, filling and mass concrete complete all as specified.

Item No.8 Use and waste of formwork to fair surfaces of sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter surfaces finished fair in forms complete all as specified.

Item No.9 Use and waste Formwork to flat sides and soffits of floor or roof beams, beam haunchings, girders, bresumers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams etc. surfaces finished fair complete all as specified.

Item No.10 M&L for mild steel TMT reinforcement bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

Item No.11 M&L for Mild steel TMT bars of dia upto 10mm, in stirrups, spacers and binders, cut to length, bent to shape required, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia, or securing with clips, complete all as specified and as directed by the Engineer-in-Charge.

Item No.12 M&L for Reinforced Cement concrete M-20 (Noninal Mix) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under reamed piles and mass concrete complete all as specified.

Item No.13 M&L for moorum/ red bajri filling in floors or pavings/ trenches laid in layers not excd 15 cm thick spread, levelled and blinded with earth and rammed including watering complete all as specified.

Item No.14 M&L for ATT Treating the top surface of filled earth at the rate of 5 lires of emulsion per square metre of surface

Item No.15 M&L for Brickwork with fly ash brick, straight or curved on plan excd 6 M mean radius in built in cement and sand mortar 1:6 complete all as specified.

Item No.16 M&L for 40mm thick PCC 1:2:4 type B0 using 12.5mm graded stone aggregate as in damp proof course to horizontal or vertical surfaces including necessary form work mixed with water proofing compound complete all as specified.

Item No.17 M&L for Brickwork with fly ash brick, straight or curved on plan excd 6 M mean radius in built in cement and sand mortar 1:4 complete all as specified.

Item No.18 M&L for Rendering 15mm thick on fair faces of brick work or concrete surfaces, in cement and sand mortar 1:4 complete all as specified

Item No.19 Supply only Integral water proofing compound (liquid) complete all as specified.

Item No.20 M&L for rendering 10mm thick on fair faces of brick work or concrete surfaces, in cement and sand mortar 1:4 top surfaces finished even and smooth without using extra cement complete all as specified.

Item No.21 M&L for Reinforced Cement concrete in cement concrete M-25 (Nominal Mix) as in beams, cantilevers, bressumers, lintels over 1.5 m span complete all as specified.

Item No.22 M& L for Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gussets plates, riveting, etc.; n exc 10 Kg each brackets, conforming to Fe-290-Gde E-165 (Brackets over 10 Kg each to be measured under ''Structural Steel"

Item No.23. M&L for preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamelled paint over one coat of red oxide Zinc chrome primer complete all as specified.

Item No.24 S&F Pre-painted galvalume aluminium zinc coating GI based profile steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa, hot dip alloy of 55% Aluminium 43.5% Zinc 1.5% Silicon and finished with resin coat on both surfaces @ 150 gm/sqm of coating (total both surfaces) as in roof covering/ cladding to wall, including flashings, ridges, valley etc fixed with self tapping screws as specified.

Item No.25 M&L for glazed ceramic coloured tiles, 300mm x 450mm/ 300 x 200 x 7mm thick, on vertical surfaces such as dados, skirting and risers to steps etc. set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10mm thick screed bed in Cement mortar 1:4 complete all as specified and directed.

Item No.26 M&L for joint free Non Skid ceramic coloured tiles (designed) 6-7mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.36 sqm (400mm x 400mm), in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 20mm thick screeding in CM 1:6 complete all as specified.

Item No.27 S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with Mild steel square tube complete all as specified and directed.

Item No.28 S&F Factory made solid panel PVC door shutter 30mm thick (style) con-sisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be cov-ered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain col-our PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification complete all as specified and directed.

Item No.29 S&F 100mm long Butt Hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised, suitable for 30mm thick shutters type designation 100C21 (ISI marked) complete all as specified and directed.

Item No.30 S&F extruded aluminium alloy handles, fabricated type polished, 125mm long all as specified.

Item No. 31 S&F Aluminium, anodised, barrel tower bolts of extruded section and fixed, 150mm length of bolt, ISI marked complete all as specified.

Item No.32 Cutting chases in brick work, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels,etc; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified.

Item No.33 M&L for 15mm nominal bore Mild steel galvanised water tubing, medium grade (ISI marked) with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified.

Item No.34 M&L for 20mm nominal bore Mild steel galvanised water tubing, medium grade (ISI marked) with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified.

Item No.35 M&L for (in repairs) PVC (SWR) floor trap, plain with grating including jointing with solvent cement, 110mm dia. outlet complete all as specified.

Item No.36 S&F 110mm bore PVC (SWR) pipes single socketed (ISI marked) IS-13592, type 'B in any length with rubber ring joints fixed to walls complete all as specified.

Item No.37 S&F 75mm bore PVC (SWR) pipes single socketed (ISI marked) IS-13592, type 'B in any length with rubber ring joints fixed to walls complete all as specified.

Item No.38 S&F PVC (SWR) bends 110mm bore (ISI marked) complete all as specified

Item No.39 S&F PVC (SWR) 110mm nominal bore pipe, Branch pieces, double (equal or unequal), ordinary or inverted (spigot or socket type), complete all as specified.

Item No.40 S&F Cast iron cowls suitable for 110mm bore pipe complete all as specified

Item No.41 S&F Stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100mm nominal bore pipe

Item No.42 M&L for preparation of new plastered surfaces of walls and distempering with distemper oil emulsion, two coats, white or tinted over a coat of alkaline resistant primer including washing floors, cleaning glass, joinery, electrical fittings, wiring etc., of drops and splashes complete all as specified.

Item No.43 M&L for two coats of exterior emulsion paint (weather coat), white or tinted over a coat of exterior primer on new surfaces of walls including washing floors, cleaning glass, joinery, electrical fittings, wiring etc., of drops and splashes complete all as specified.

Item No.44 M&L for Powder coated (minimum thickness of powder coating 50 micron) Aluminium frame for doors, windows, ventilators and fixed glazing with one or more rebates including jointing cleat, snap beading and rubber gasket etc. for fixing etc. complete all as specified. (Note :- 1. Weight of Aluminium sections shall only be measured. 2. Glass panes shall be paid separately at supply only rates)

Item No.45 S&F 4mm thick (nominal) Sheet glass, ordinary quality, in squares, not exceeding 0.50 sqm each pane fixed with oil putty at any height in portion (part) complete all as specified.

Item No.46 S&F Cast Brass chromium plated shower rose 125mm size with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and shown in drawings.

Item No.47 S&F Bib taps, cast copper alloy with crutch handle, screwed for 15mm bore dia. iron pipe or for brass ferrule and fixed complete all as specified

Item No.48 M&L for 15-16mm thick granite stone slab (of any type), bedded over screed bed and jointed in cement mortar to match the colour of slab as in flooring, polishing and grinding, over and including 15mm thick screeding in CM 1:4 complete all as specified. (Note:- The unit rate quoted by the contractor shall be deemed included screed bed).

Item No.49 M&L for broken stone or boulder hardcore (granite/ basalt/ trap) of gauge n exc. 63mm, deposited, spread and levelled in layer n exc. 15 cm thick, watered and rammed to a true surface complete all as specified.

Item No.50 M&L for Plain cement concrete type C2 (1:3:6), using 40mm graded crushed stone aggregate, 75mm thick, as in path/ plinth protection/ paving finished even and fair complete all as specified.

Item No.51 S&F vitreous china wash basin oval (WHB), size 510mm x 450mm excluding supply of taps, but including waste fittings, brass Chromium plated for glazed basins etc. with long screw shanks and flt nuts complete all as specified.

Item No.52 S& F Brass Trap 300mm, designer wall connection pipe and wall flange, complete all as specified.

Item No.53 Supply & Fixed Pillar taps, cast copper alloy, with capstan heads, chromium plated, Fancy type screwed down for 15mm bore pipe, high pressure, with or without l'ettered ' 'HOT' or 'COLD' with long screwed shanks and fly-nuts, screwed for iron pipe; complete all as specified.

Item No.54 Supply & Fixed PTMT connections 15mm size with PTMT nuts of length 450mm complete all as specified.

Item No.55 S&F Chromium plated fancy type Stop/ angle valves, cast copper alloy, screwed down for 15mm bore dia. pipe, high pressure, with crutch handle, screwed externally both ends for unions etc. and fixed complete all as specified

Item No.56 Supply & Fixed 32mm bore Low density polyethylene pipes (LDPE) of pressure rating 6 kgf/cm2 fixed to wash basin/ sinks as waste pipe complete all as specified.

Item No.57 S&F Sheet glass shelf assembly consisting of 5.50mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long, complete all as specified.

Item No.58 S&F looking mirror consisitng 5.5mm thick glass mounted on 6mm thick plywood and providing decorative type wooden beadings of 1st class HW teak of size excd 3 and not excd 6 sqcm and finish glossy with french polish over a coat of wood filler complete all as specified.

Item No.59 M&L for Rendering 15mm thick on fair faces of brick work or concrete surfaces, in cement and sand mortar 1:6, complete all as specified.

Item No.60 S & F 40mm bore PVC Low density polyethylene (LDPE) pipes of pressure rating 6 kgf/sq. cm laid in floors or trenches including bends and making holes in wall and trenched where required at site. complete all as specified

Item No.61 S&F 18mm thick factory made PVC sheet both side pre-laminated sheet for ktichen cabinet shutter, shutter bent at 90 degree and finish all edges at level for marking edge lipping bending for 0.5mm thick PVC sheet lipping at all four edges using bonding tape etc complete all as per specified and directed.

ItemNo.62 S&F one sides laminated factory made PVC shelf/ partition/ cupboard of required size consisting of panel of 18mm thick required size consisting of panel of 18mm thick celuka PVC ply and for supporting the hold of shelf/ partition and shall provided 3 edges in size 18mm x 18mm as per required lenght the front side of the edge visible in the front of the shelf/ partition to be edge lipped by 18mm widht x 1mm thick PVC sheet of density 600 kg/cum manufactured by ISO 9001-2015 Certified Company, using solvent cement etc. complete all as per specified and directed.

Item No.63 S&F 50 x 15mm size magnet door catcher for closing for PVC door shutter complete all as specifid and directed.

Item No.64 S& F 100mm size MS mat/glossy finish handle complete all as specfied and directed.

Item No.65 S&F stainless steel pluton Heavy Soft close Hydraulic concealed Hinges for full overlay of door complete all as specified and as directed.

Item No.66 S&F Rotational moulded poly-ethylene multilayer water storage tanks (ISI marked) (cylinderical vertical with closed top) 500 litres capacity, hoisted and fixed in position complete all as specified.

Item No.67 S&F Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball, suitable for 20mm bore pipe, screwed for iron pipe and fixed. (Minimum weight 20mm-210 gms.) complete all as specified.

Item No.68 S&F Gunmetal, globe or gate valves, with iron wheel head, screwed both ends for 20mm bore dia. iron pipe and fixed complete all as specified.

Item No.69 Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning and removing all scale and dirt, etc., from tanks and from mouths of circulating pipes, etc. and hoisting if required reconnecting and refixing in position (Exc 250 litres but not exceeding 500 litres complete all as specified and directed. (Cleaning shall not be measured separately)

Item No.70 M&L for Cement concrete type B2, 1:2:4 (2mm graded aggregate) in sub base for PVC water tank, complete all as specified and directed.

Item No.71 Excavating over areas exc 1.5 m wide and exc 1.5 m in depth for manholes, and septic tanks in depth and getting out in soft/ loose soil Complete all as specified and directed.

Item No.72 M&L for Plain cement Concrete (1:3:6) type C2 bed to 150mm bore drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; in complete all as specified.

Item No.73 M&L for Plain cement Concrete (1:3:6) type C2 bed to 200mm bore drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; in complete all as specified.

Item No.74 M&L for Reinforced concrete pipes, class NP2 ,150mm bore, laid and jointed complete with collars all as specified.

Item No.75 M&L for Reinforced concrete pipes, class NP2, 200mm bore, laid and jointed complete with collars all as specified.

Item No.76 M&L for 150mm bore Salt - glazed stone ware drain pipes, Class 'SP2' laid in trenches and jointed as specified.

Item No.77 M&L for 200mm bore Salt - glazed stone ware drain pipes, Class 'SP2' laid in trenches and jointed as specified.

Item No.78 Removing excavated material (soil) exceeding 1.5km and not exceeding 5 km and depositing where directed at a level not exceeding 1.5 m above the starting point all as specified.

Item No.79 M&L for precast cement concrete 1:2:4 type B1 as in landings, cover slabs (for manholes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces set in cement mortar 1:4 complete all as specified.

Item No.80 M&L for Reinforced Cement concrete 1:2:4 type B1 using 20mm graded crushed stone aggregate as in slabs supported on walls, beams and columns, in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified.

Item No.81 Use and waste of form work to flat soffits of suspended deck slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) surfaces finished fair as specified in SSR Part-I Clause 4.11.16.2(a) as specified complete all as specified.

Item No.82 M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping ends for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.90mm dia. complete all as specified .

Item No.83 M&L for TMT bars 5mm dia. and over up to and including 10mm dia. in stirrups, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia. or securing with clips complete all as specified.

Item No.84 M&L for plain cement concrete type B1 (1:2:4) using 20mm graded stone aggregate as in, cills, steps; seismic and other similar band, copings, covings bed plates, and like including weathering slightly rounded or chamfered angles including necessary formwork complete all as specified.

Item No.85 M&L for brick work with fly ash brick, straight or curved on plan to any radius in half brick thick walls built in CM 1:4.

M/S Ashish Construction

M/s Shree Ganesh Traders

Jamna Constructions

APconstruction

NIDHI CONSTRUCTION

sunway associates