Tender for execution of work under MC and EW(D. and R. of. Bld) to Staff Quarter at Ahukhana, Distt. Burhanpur (M.P.)

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials. All kinds of soil (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Dry stone pitching 22.5 cm thick including supply of stones and preparing surface complete. (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size) (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centring, shuttering, finishing and reinforcement - All work up to plinth level :1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centring, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size) (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Centring and shuttering including strutting, propping etc. and removal of form work for : Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc. (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Centring and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Edges of slabs and breaks in floors and walls Under 20 cm wide (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete up to plinth level. Cold twisted bars (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement. 12 mm cement plaster (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement. 20 mm cement plaster (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

20 mm cement plaster of mix : 1:4 (1 cement: 4 coarsesand) (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600 X 600 mm (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Dismantling of manhole including R.C.C. top slab, C.I. cover with frame, including stacking of useful materials near the site and disposal of unserviceable materials within 50 m lead as per direction of Engineer-in-charge: Rectangular manhole 90x80 cm and 45 cm deep (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in-Charge. (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sq. metres and below (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040 mm bowl depth 250 mm (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Providing and fixing single equal plain junction ofrequired degree : 100x100x100 mm Sand cast iron S&Sas (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using M.S. angels 40x40x6 mm for diagonal braces (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strikeplate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: Profile C Fixing with adjustable lugs with split end tail to each jamb (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand :4 graded stone aggregate 20 mm nominal size) (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan. (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 40 mm dia. (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Providing and fixing soil, waste and vent pipes : 100 mmdia Sand cast iron S&S pipe (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes : 100 mm dia pipe (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 15 mm nominal bore (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 15 mm nominal outer dia Pipes (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

20 mm nominal outer dia Pipes (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

25 mm nominal outer dia Pipes (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Provision for electrical items i.e.., Fan, tube light, bulb, switches, wire, casing pipe and related articles including cost of materials and labours etc for 2 Nos. staff quarters (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Provision for Electric meter 3 Phase working load 10 HP @ 10 hrs for staff quarter and monument premises supply though MPEB including cost of security deposit, service cable, conduit casing and labours etc (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Provision for solar lightening system over roof of staff quarter useful for quarter and monument premises having capacity 3 Kva including cost of material and labours. (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Providing and applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1) and two coats of undiluted elastomeric waterproofing liquid (dry film thickness of complete application/system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of Engineer-in-Charge. (This provision is inclusive of GST hence no GST Amount is to be quoted by the Bidder)

Baba Construction (BID ID -3312166)

M/S VIRENDRA KUMAR JAIN (BID ID -3311003)