Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Status |
|---|---|---|
| 1 | Admitted-Fee/PreQual/Technical/Finance 13 L K ROAD KOEL OFF BOMBAY POONA ROAD KIRKEE PUNE MAHARASHTRA 411003 INDIA | PUNE | MAHARASHTRA | 411003 | Admitted-Fee/PreQual/Technical/Finance |
| 2 | Admitted-Fee/PreQual/Technical/Finance PLOT NO 18 G I D C INDUSTRIAL ESTATE SAVLI ALINDRA VADODARA GUJARAT 391775 | VADODARA | GUJARAT | 391775 | Admitted-Fee/PreQual/Technical/Finance |
Tender Value
Refer Docs
Closing Date
22 Aug 2022, 9:00 amClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
COMMODORE SUPERINTENDENT OF YARD, NSRY, PORT BLAIR
COMMODORE SUPERINTENDENT OF YARD, NSRY, PORT BLAIR
RRC ROUTINES/REPAIR WORK OF KIRLOSKAR MAKE ENGINES FITTED ONBOARD LST , NOPV AND CORVETTE
2022_IDS_540586_1
NSRY/COM/112 (C) 2 (b)/RRC/CID-2721
Limited
Miscellaneous Works
Works
365 days
NAVAL SHIP REPAIR YARD, PORTBLAIR
AS PER TENDER DOCUMENTS
2 documents required · 2 mandatory
₹0
Yes
23 Aug 2022
25 Jul 2022
23 Aug 2022
25 Jul 2022
22 Aug 2022
27 Jul 2022
25 Jul 2022 - 27 Jul 2022
Amount
Note: Bidders are requested to quote GST in terms of % only. Example If GST is 18% fill 0.18 in the GST column
SERVICES
LST L KESARI CLASS
Service charges for undertaking operational defects required to be carried out during ops-cycle on Main Engines
Inspection of Main Engine not starting issue.
Inspection of Main Engine overspeeding issue.
Main Engine Clutch/ Declutch issue.
Replacement of Main Engine controller from OBS 1 no.
Repair of Main Engine Controller and calibration 1 no.
Removal, overhauling and refitment of cylinder head including replacement of valves seat & injector sleeves.
Renewal of injector pocket sleeve fpr 1 no.
inpection and rectification of high fresh water temperature alarm to be reftified.
Inspection and retification of high lub oil temperature alarm to be rectified.
Inspection and retification of high exhaust temperature alarm to be rectified.
Inspection and retification of heavy exhaust leakage from manifold .
Main Engine RPM hunting / fuel rack fluctuation issue to be rectified.
Replacement of 1 no. Main Engine fuel injection pump (FIP) from OBS.
Overhauling and calibration of 1 no. Main Engine fuel injection pump (FIP).
Replacement of engine Governor/ Actuator and setting from OBS.
Overhauling and calibration of Main Engine Actuator 1 no.
Main Engine Turbocharger replacement 1 in no.
Main Engine rack'zero' setting and linerziation.
Inspection on increasing of heavy fuel leak off on Main Engine.
Replacement of Air seal on 1no. Cylinder head.
Overhauling of fuel filter Hydraulic motor
Service charges for undertaking control jobs on LST L class of Ships
Inspection & calibration of Over speed sensor,SVAE card,Over speed solinoid valve and related electrical circuit.
Inspection & calibration of Lub oil pre transmitter for safety,Lub oil pre transmitter for indication,SPH card & related electrical circuit. Replacement of item, if required.
Inspection & calibration of SE card, Current amplifier,Analog gauge & related electrical circuit
Inspection & calibration of Temperature sensor (2 nos),RTD converter (2 nos),related electrical circuit
Inspection & calibration of emergency Stop switch (2 nos),ICM card, related electrical circuit
Inspection & calibration of Gear box low pre switch & related electrical circuit
Inspection & calibration of FW level switch,ICM card & related electrical circuit
Inspection & calibration of Safety reset switch, RGM card & related electrical circuit
Inspection & calibration of Jacumatic valve, ACM card & related circuit
Inspection & calibration of all Jocumatic valve checking & related circuit
Inspection & calibration of Inter lock checking as per drawing & related electrical circuit
Inspection & calibration of Start & Stop related electrical circuit & Engine Controller checking
Inspection & calibration of Clutch & Declutch related electrical circuit & Engine Controller checking
Inspection & calibration of Logic Input/Output,Analog input/output,configaration & others parameters
Inspection & calibration of Fuel Rack sensor & calibration by Engine Controller
Inspection & calibration of Lub oil flow switch,Lub oil stater panel,Engine controller & related electrical circuit
Inspection & calibration of Temperature sensor (2 nos),RTD converter (2 nos),related electrical circuit
Inspection & calibration of local guages
Checking all terminal's proper connectivity
Inspection & calibration of SVAE,SPH,SE,ICM,ACM,RGM card
Inspection & calibration of Start/Stop switch & related electrical circuit
Inspection & calibration of Clutch/Declutch switch & related electrical circuit
Inspection & calibration of Pressure Transmitter,Gauges & related electrical circuit
Inspection & calibration of Temperature sensor,Module & related electrical circuit
Inspection & calibration of Lamp checking & related electrical circuit
Inspection & calibration of 10 no's srensor & Thermocouple board, PLC & related electrical circuit
Inspection & calibration of all alarms related electrical circuit
Inspection & calibration of Combinator, Engine Controller & related electrical circuit
Inspection & calibration of 07 Nos. Temerature checking & synchronising with RCR reading
Calibration remote speed analog speed & synchronising with RCR
Inspection & calibration of gas valve, air valve, P2-P4 valve jaucomatic valve engine controller
Inspection & calibration of Pre SW,PreTransmeter,Jaucomatic valve,Engine controller
Service charges for undertaking 4000 Hrly routine on BME jobs
Undertake inspection of rocking gear including removal visual inspection dimensional checking and replacement of bushes and refitting of the rockers. KOEL note : only visual inspection of rocking gear considered
Injectors to be calibrated/ reconditioned
check fuel injection pump rack for free movement and examine cam follower rollers
Inspect electric actuator & replace oil
Inspection & overhauling of shut off valve & by pass valve.
Check the sliding of the injection pump rack
Visually inspect cam & rollers
Check the “Geislinger” coupling resilient part
Clean the oil/sea water and fresh water coolers
Inspection of LO priming pump
clean the crankcase mist outlet system
In addition to above, following jobs are required to be undertaken as per Naval Maintops at 4K
Check condition of serrated bush of the fuel booster pump drive. replace serrated bush if worn out.
Dismantle and recondition / renew the engine air starting valves and air distributor.
Evaluate functionality of lub oil and fresh water thermostat fitted in the systems based on fw/lo temp. renew thermostatic elements
Check for correct torque tightening of rocker arm pedestal fasters and tappet clearance
Service charges for undertaking 8000 Hrly routine on BME jobs
(a) Check condition of serrated bush of fuel booster pump drive. (b) Replace serrated bush if worn out.
(a) Remove injectors test for spray tightness and atomization. Repair/ Replace defective/ worm out parts calibrate & refit injectors.
Visually inspect rocker gear
Replace oil of barring gear motor reducer
Check coupling resilient parts
Replace the FW & SW pump packing KOEL Note: Water pump overhauling considered
Inspect the Main Starting air Valve
a) Inspect Electric actuator b) Replace hydraulic actuator oil
(a) Clean the self-cleaning fuel filter (b) Repair/replace defective components (if necessary)
Repair/replacement of inspection door discharge valve flaps if found defective in operation
Adjust the valve backlash on cold engine
Inspect starting air valve flap & rings
Check the sliding of the injection pump rack
Carryout crankcase inspection
Visually inspect cam & rollers
Inspect the air distributor disc
(a)Check thermostat for correct functioning. (b) Replace if required.
Carry out inspection & mechanical cleaning of turbocharger compressor wheel, casing & diffuser without removing the rotor.
(a) inspect shut off valve & by pass valve (b) Replace the guiding bushes on bypass valve
Inspect the timing gear teeth
Replacement of air tube of Clutch
In addition to above, following jobs are required to be undertaken as per Naval Maintops at 8K
Inspection of charge air cooler tubes & leakage from water chamber closing plates which involves: (A) Removal & Re-fitment of CAC (B) Overhaul of Charge Air Cooler including repair of leaking air cooler tubes & defective water chamber closing plates (C) Pressure testing post fitment after repairs
(a)Pressurize whole system & check system for leaks. (b)Rectification of defects of the system if observed
(a) Check wear & ovality of Exhaust Valve guide bushes & condition of exhaust valve seats. For the 4 nos units dismantled. (b) Repair/replacement of the defective exhaust valve guide bushes and defective exhaust valve seats.(if necessary)
(a)Remove & inspect gasket on valve carrier on oil pump suction side/valve box. (b)Replacement of gasket on valve carrier on oil pump suction side/valve box
(a)Inspection of compensator joints for cracks. (b)Renewal of joints as necessary
Remove & replacement of air intake filters
(a)Inspection of condition of guard of air intake filters for deterioration/damage. (b)Renewal of guard as necessary
NOPV SARYU CLASS
Service charges for undertaking operational defects required to be carried out during ops-cycle on Main Engines
Inspection of Main Engine not starting issue.
Inspection of Main Engine overspeeding issue.
Main Engine Clutch/ Declutch issue.
HMI display not working and repair to be done 1 no.
Replacement of Main Engine controller from OBS 1 no.
Repair of Main Engine Controller and calibration 1 no.
Removal, overhauling and refitment of cylinder head including replacement of valves seat & injector sleeves.
Renewal of injector pocket sleeve for 1 no.
inpection and rectification of high fresh water temperature alarm to be reftified.
Inspection and retification of high lub oil temperature alarm to be rectified.
Inspection and retification of high exhaust temperature alarm to be rectified.
Inspection and retification of heavy exhaust leakage from manifold .
Main Engine RPM hunting / fuel rack fluctuation issue to be rectified.
Replacement of 1 no. Main Engine fuel injection pump (FIP) from OBS.
Overhauling and calibration of 1 no. Main Engine fuel injection pump (FIP).
Replacement of engine Governor/ Actuator and setting from OBS.
Overhauling and calibration of Main Engine Actuator 1 no.
Main Engine Turbocharger replacement 1 in no.
Main Engine rack'zero' setting and linerziation.
Inspection on increasing of heavy fuel leak off on Main Engine.
Replacement of Air seal on 1no. Cylinder head.
Service charges for undertaking control jobs on NOPV class of Ships
Calibration of ME pressure transmitter & indication on LCP HMI & MCR (RCMS)(08 Nos.)- ME: LO inlet / TC oil inlet / FW inlet/ Fuel inlet/ SW pump outlet / Start air / TC air sealing / Control air) -- reading @ HMI-LCP & MCR
Calibration of ME Temperature sensors (RTD’s) & indication on LCP HMI & MCR (RCMS)(09 Nos.)--reading @ HMI-LCP & MCR
Check exhaust gas thermocouple sensors & temperature indication. (24 Nos.) thermocouple & 02 Nos. compensation probe per engine) --reading @ HMI-LCP & MCR
Main engine bearing temperature system to be checked. (11 in main engine bearing sensor per engine) --reading @ HMI-LCP & MCR
Main Engine conrod bearing temperature system to be checked. (10 Nos. main engine conrod bearing sensor per engine, MTP cards – 03 Nos./engine) --reading @ HMI-LCP & MCR
Calibration of main engine safeties. (12 Nos.)
Calibration of main engine RPM system (SE card – mengine RPM, RPM sensor, over speed valve & SVAE card) Check and test engine RPM system SE/SVEM units. Calibrate the engine RPM thresholds and over speed threshold at no load condition Check main engine RPM
Calibration of main engine lub oil safety care (LO pressure Tx, SPH card, SE card) Calibration checks of main engine starting logic & interlocks Calibration checks of main engine clutch / de-clutch logic & interlock STC valve limit switch check (air/gas & P2-P4 by-pass valve)
Calibration of main engine fuel rack indication system
Renewal of TC sensor & calibration of ME turbo charger RPM indication system (TC sensor / pre-amplifier)
Calibration and testing of ME fresh water temperature controller system (FW temp. sensor / Temperature regulator / EP converter / positioned)
Main Engine float switches for alarms indications to be checked and defects to be rectified. (05 Nos.) (fuel leakage/FW level / crank case level)
Main Engine limit switches for alarms / indications to be checked and defects to be rectified (fuel control handle limit switch / fuel control lever @ stop/ turning gear limit Switch)
Main Engine filter clogging sensor for alarms indications to be checked and defect to be rectified. (02 Nos.) (fuel filter / Lub oil filter)
Check all alarms signaling lamp in LCP related to main engine.
Check ME lub oil pump flow switch and carry out logical checks of relays in LCP
Functional & logic checks of TC air blower operation Functional & logic checks of crank case extractor operation
Inspect and overhaul and the over speed safety slide valve
Overhaul / inspection pneumatic filters of ME pneumatic control system (03 Nos./engine)
Overhaul pneumatic control panels inside LCP(02 nos.)(Electro- pneumatic distributor & solenoid valve)
Inspection of pneumatic components of main engine control system/ (ME pneumatic supply frame) – 40/7 bar reducing panel
Inspection of pneumatic components of main engine jet assist control system. (ME pneumatic supply frame) – 40/23 bar reducer & reducing panel
Overhauling of pneumatic components (over speed solenoid valve, NRV) of local main engine over speed panel in engine room
Inspection of pneumatic reducer / regulating valve of ME fresh water system
Overhauling of GALI pneumatic starters of Main Engines. To be overhauled and operation to be proved
Overhauling and calibration of main engine oil mist detector alarm system check.
Clean and check the main engine turning gear pneumatic interlock safety mechanism.
Overhaul Main Engine fuel pneumatic system valve.
Clean & Overhaul load limiter and set
Clean & Overhaul governor servo booster
Calibration of main engine local mechanical pressure gauges
Calibration of main engine local mechanical temperature gauge (Thermometers)
Overhauling of air/ gas & bypass valve
Renewal of LCP engine controller with basic calibration setting.
Local control panel PLC & HMI program, serial link communication check with MCR checking.
Local control panel dust free, contract cleaning & connection fighting
Service charges for undertaking 4000 Hrly routine on BME jobs
Undertake inspection of rocking gear including removal visual inspection dimensional checking and replacement of bushes and refitting of the rockers. KOEL note : only visual inspection of rocking gear considered
Injectors to be calibrated/ reconditioned
Inspect electric actuator & replace oil
Run the electronic over speed test
Inspection & overhauling of shut off valve & by pass valve.
Check the sliding of the injection pump rack
Visual inspect cam & rollers
Check the “Geislinger” coupling resilient part
Check the pneumatic starter
Clean the oil/sea water and fresh water coolers
Inspection of LO priming pump
clean the crankcase mist outlet system
In addition to above, following jobs are required to be undertaken as per Naval Maintops at 4K
Check condition of serrated bush of the fuel booster pump drive. replace serrated bush if worn out.
Evaluate functionality of lub oil and fresh water thermostat fitted in the systems based on fw/lo temp. renew thermostatic elements
Check for correct torque tightening of rocker arm pedestal fasters and tappet clearance
Service charges for undertaking 8000 Hrly routine on BME jobs
(a) Check condition of serrated bush of fuel booster pump drive. (b) Replace serrated bush if worn out.
(a) Remove injectors test for spray tightness and atomization. Repair/ Replace defective/ worm out parts calibrate & refit injectors.
Visually inspect rocker gear
Check coupling resilient parts
Replace the FW & SW pump packing KOEL Note: Water pump overhauling considered
(a) Clean the self-cleaning fuel filter (b) Repair/replace defective components (if necessary)
Repair/replacement of inspection door discharge valve flaps if found defective in operation
Adjust the valve backlash on cold engine
Check the sliding of the injection pump rack
Carryout crankcase inspection
Visually inspect cam & rollers
(a) Carry out inspection & mechanical cleaning of turbocharger compressor wheel, casing & diffuser without removing the rotor.
(a) inspect shut off valve & by pass valve
(b) Replace the guiding bushes on bypass valve
Inspect the timing gear teeth
Inspect the over speed slide valve, replace the gasket
Inspect the over speed solenoid valve
Clean the crankcase mist out system
In addition to above, following jobs are required to be undertaken as per Naval Maintops at 8K
Inspection of charge air cooler tubes & leakage from water chamber closing plates which involves: (A) Removal & Re-fitment of CAC (B) Overhaul of Charge Air Cooler including repair of leaking air cooler tubes & defective water chamber closing plates (C) Pressure testing post fitment after repairs
CORVETTE KULISH CLASS
Service charges for undertaking operational defects required to be carried out during ops-cycle on Main Engines
Inspection of Main Engine not starting issue.
Inspection of Main Engine overspeeding issue.
Main Engine Clutch/ Declutch issue.
Removal, overhauling and refitment of cylinder head including replacement of valves seat & injector sleeves.
Renewal of injector pocket sleeve fpr 1 no.
inpection and rectification of high fresh water temperature alarm to be reftified.
Inspection and retification of high lub oil temperature alarm to be rectified.
Inspection and retification of high exhaust temperature alarm to be rectified.
Inspection and retification of heavy exhaust leakage from manifold .
Main Engine RPM hunting / fuel rack fluctuation issue to be rectified.
Replacement of 1 no. Main Engine fuel injection pump (FIP) from OBS.
Overhauling and calibration of 1 no. Main Engine fuel injection pump (FIP).
Replacement of engine Governor/ Actuator and setting from OBS.
Overhauling and calibration of Main Engine Actuator 1 no.
Main Engine Turbocharger replacement 1 in no.
Main Engine rack'zero' setting and linerziation.
Inspection on increasing of heavy fuel leak off on Main Engine.
Replacement of Air seal on 1no. Cylinder head.
Service charges for undertaking control jobs on Corvette class of Ships
Checking/ calibration of gear box bearing temperature system
Following items checked and calibration 1. 10 in nos. gear box bearing temperature sensor P100 insulation, hot checked for reuse. 2. checked gear box local junction box connection tightening. 3. Pyro cable from MER to SCC (EC36) 4. Temperature scanner checked & calibration 5. Calibration and checked thresold scanner gear box alarm bearing 1 & 2 @ 85°C, scanner gear box alarm bearing 3, 4, 5 & 6 @80°C, scanner gear box alarm bearing 7, 8, 9,10 @70°C
Checking in status indication in SCC 1. Engine clutched (61) 2. Engine turning gear engaged (62) 3. Gear box turning gear engaged (63) 4. Low ME fresh water temperature (49) 5. Fuel control handle locked (50) 6. Very low ME lub oil pressure (51) 7. Pre-lub oil pump "ON" (52) 8. Supply failure 24V DC (66) 9. Supply failure 115V AC (65) 10. Safeties OFF (56) 11. Local control (58) 12. Remote control (57) 13. Simulation ON (59) 14. Emergency stop (S23) 15. Emergency Control (S2) 16. Increasing pitch (60)
Checking in status indication in SCC 17. Decreasing Pitch (64) 18. Simulation on 19. Load (67) 20. Overload (68) 21. Ahead (54) 22. Astern (55) 23. Zero pitch (53) Local indication 24. SCC control (1) 25. Local control (5) 26. Increasing pitch (3) 27. Decreasing Pitch (4) 28. Simulation on (2) Bridge Indication 1. ME clutched 2. ME De-clutched 3. Safety stop
To calibrate remote operation of control level/ combinator with ME RPM System
Calibreate of remote operation of control lever/ combinator with ME RPM system (idle RPM-1000 RPM)
Checking of auto operation of gear box motor driven pump.
Checking and proving the auto operation of gear box motor driven pump
Checking of alarm modules & alarm
Alarm modules: 12nos per engine (04 alarms each module) 1. High engine bearing temperature (9) 2. Break engaged (47) 3. Spare (48) 4. Spare (38) 5. Engine control failure (23) 6. Telegraph failure (14) 7. Remote control air failure (37) 8. Line control failure (37) 9. Spare (33) 10. Propeller control failure (31) 11. Sapre (35) 12. Spare (34) 13. Exhaust gas temperature failure (19) 14. Low level in crank case (18) 15. Sapre (46) 16. Low ME starting air pressure (24) 17. Over speed (1) 18. Spare (42) 19. Spare (43) 20. Low ME fresh water pressure (6) 21. Low ME Lub oil pressure (3) 22. Safety stop (2) 23. High ME fresh water temperature (7) 24. Low ME fresh water level (8) 25. Low ME sea water pressure (5)
Checking of alarm modules & alarm 26. High ME lub oil temperature (4) 27. Low diesel oil pressure (16) 28. Diesel oil leakage (17) 29. Low over speed air pressure (22) 30.Over speed system failure (21) 31. Spare (45) 32. Temperature monitor failure(20) 33. Low gearbox lub oil pressure (10) 34. Low propeller control oil pressure (30) 35. High OD box oil pressure (44) 36. Very low propeller oil pressure (25) 37. High gearbox bearing temperature (12) 38. Low gearbox control oil pressure (11) 39. Propeller oil filter clogging (26) 40. Low level in propeller oil head tank (27) 41. High gearbox oil temperature (15) 42. Low gearbox sea water pump pressure (13) 43. Low level in propeller sump tank (28) 44. High propeller oil temperature (29) 45. Very low propeller control oil pressure (39) 46. Gear box oil filter clogging (40) 47. High propeller bearing temperature (32) 48. Spare (41)
Checking main engine starting interlocks and proving
Following main engine starting interlocks 1. Gearbox turning gear engaged 2. Local/ remote control 3. Lub oil priming pump 4. Main engine safety reset 5. Fuel control handle locked 6. 150RPM threshold 7. Safeties off
Checking of pneumatic components on main engine in MER
Checking following items on pneumatic components on main engine in MER 1. Turning gear linit switch 2. Starting air valve 3. Over speed solenoid valve 4. Over speed spool valve 5. Governor servo booster 6. Fuel start stop rack limiter
Checking/ calibration of ME exhaust gas temp. System
Following items checked and calibration 1. 22 in nos. Exhaust gas thermocouple 2. 02 in nos. Compensation RTD 3. 02 in nos. Pyro pipes 4. 02 in nos. Pyro cable from MER to SCC (EC 64 A & EC 64 B) 5.Temperature scanner checking & calibration. Scanner Cyl. deviation + VE 60°C Scanner Cyl. injection fail 200°C Scanner Cyl. temp. high alarm 600°C Scanner Cyl. turbo inlet high temp. alarm 650°C Scanner Cyl. turbo outlet high temp. alarm 580°C
Chacking / calibration of ME bearing temperature system
Following items checked & calibrated 1. 10 in nos. ME bearing temperature sensore PT 100 insulation hot check for reuse 2. 02 in nos. Pyro pipes 3. 02 in nos. Pyro cable MER to SCC (EC 66 & EC 67) 4. Temperature scanner checked & calibration 5. Calibration of alarm and safety threshold (115°C & 120°C)
Checking main engine safeties & proving
Following main engine safeties calibrated and proved with trial team 1. Overspeed 1120 RPM with haft speed mode at 560 RPM proved. 2. Very low main engine fresh water level. 3. Very high fresh water temperature : 95°C 4. Very high main engine lub oil temperature : 90°C 5. Very high temp of ME bearing 120°C 6. Very low ME Lub oil Pressure. (a) 400<n <650 RPM : P23 1.2 bar (b) 650 <n <850 RPM : P24 2.7 bar (c) n > 850 RPM : P25 4.1 bar 7. Very low gear box lub oil pressure : 1.0 Bar 8. Emergency stop (MCR)
Checking Sensors on Main Engine
Checked and proved operation of main engine sensors 1.Fuel oil leakage :02 nos. 2. Fuel control handle lock switch 3. Turning gear electrical switch 4. Crank case lub oil level switch
Calibration of main engine RPM system & RPM threshold module & over speed threshold unit.
Checked and calibrated following components (unit) in ME RPM system 1. SVEM unit 2. AFSEM unit 3. RPM pre amplifier unit 4. ME RPM magnetic pick up. 5.CD1 / CD2 cable 6. Following RPM threshold checking SPEED SIMULATION FOR RESPECTIVE RPM THRESHOULD (a) AFSEM THRESHOLD NO.1 - 150 RPM (b) AFSEM THRESHOLD NO.2 - 400 RPM (c) AFSEM THRESHOLD NO.3 - 540 RPM (d) AFSEM THRESHOLD NO.4 - 650 RPM (e) AFSEM THRESHOLD NO.5 - 850 RPM (f) AFSEM THRESHOLD NO.6 - 950 RPM (g) SVEM OVERSPEED - 1120 RPM SAFETY STOP 7. Calibration of RPM indicator in SCC, MER and bridge (P20, P13 and P30)
Checking of over speed system at no load
Checked over speed trip at no load 1. Main Engine over speed system checked with simulation. 2. Calibratied of over speed threshold. Testing of over speed at half speed i.e. 560 RPM proved while engine is running.
Checking & proving simulation operation of main engine 1. Checked Main Engine Safeties simulation 2. Checked of main engine RPM simulation 3. Checked of main engine fuel rack simulation 4. Checked of CPP pitch simulation and proved
Overhauling & proving the operation of P2-P4 valve 1. Checked P2-P4 valve operation 2. Checked and calibrated of supercharging air pressure transmitter and threshold module (MSA89) 3. Proved the operation of valve.
Calibration of fuel rack indicator with local indication on main engine
Calibration of fuel rack indicating system 1. Checked of fuel rack sensor. 2. Calibrated of GDL unit. 3. Calibration of fuel rack indicator in MCR and bridge (P16) carried out
Checking and proved auto operation of main engine lub oil priming pump.
Checking operation of fresh water pre-heater
Checking pneumatic engraved circuit components in SCC
Checked operation of following items on pneumatic engraved circuit components in SCC. 1. Electro-pneumatic solenoid valves. (a) Logical Stop : 13/1 (b) Starting : 13/2 (c) Slowing down : 13/3 (d) Clutch : 13/4 (e) De-clutch : 13/5 (f) Safety de-clutch : 13/6 (g) safety stop : 13/7 (h) Safety stop test : 13/8 (j) Safety set point 2. Pneumatic distributor (a) Logical stop : 14/1 (b) Clutch :14/3 (c) Starting : 15/1 (d) set point blocking :15/2 (e) Safety stop : 15/3 (f) Clutch blocking : 15/4 (g) Set point blocking : 15/5 (h) Clutch test : 15/6 (j) Starting test : 15/7 (k) Logical stop set : 15/8 (l) Safety stop set : 15/9 (m) Safety set point : 15/10 3. Pressure regulator :17 4. Strainer : 20/1, 20/2, 20/3, 20/4, 20/5, 20/6, 20/7, 20/8 5. Emergency speed set point regulator : 21/1
Checking pneumatic components in local MER
Checking pneumatic components in local air reducing panel in MER
Service charges for undertaking 1500 hrly routine on BME jobs
1. Inspection & draining of vibration damper chamber
2. Replace Glacier filter element
Service charges for undertaking 3000 Hrly routine on BME jobs
Clean and check all injectors.
Visual inspection of inlet and outlet valve springs & rocker arm (For 2 nos. cylinders)
Examine cams and rollers
Check fuel rack movement
Inspection & Cleaning of Air distributor (Starting air valves overhauling not covered)
Check replace sealing filters of injection pumps
Inspection & draining of Vibration Damper chamber LO system through front cover
Tappet setting to be carried out. Initial readings to be recorded (for 6 units)
Check condition of serrated bush of fuel booster pump drive. Replace serrated bush if worn out.
Carryout chemical cleaning of water and air spaces of charge air cooler. Pressure test water side post cleaning to maximum 5 bar.
Carryout inspection and mechanical cleaning of turbocharger compressor wheel, casing and diffuser without removing the rotor.
Service charges for undertaking 6000 Hrly routine on BME jobs
Clean and check all injectors.
Examine cams and rollers
Check engine foundation bolts and anchor bolts Tightening torque
Check fuel rack movement
Check replace sealing filters of injection pumps
Tappet setting to be carried out (for 6 units)
Two pistons, connecting rod assemblies, cylinder heads and con rod bearings to be examined per engine
Visual examination of timing gear train teeth
Inspection & examination of turbocharger and cleaning of thecompressor & turbine casing.(Replacement of bearings, repair to water casing, rotor balancing, removal & refitment is not covered in this scope If required will be charges extra.)
Inspection of starting air disc and starting air valves (06 no starting air valves)
Chemicle Claeaning of CAC Including removal and refitment
Fuel Booster Pump Drive and Governor Drive Bearings, Serrated Bush Replacement
Fuel booster pump overhauling
Visual Inspection of Valkun coupling
Inspection of Spring packs of vibration damper by extraction from slots one at a time
Remove any two crank shaft bearings and carry out gauging. Inspect the crank shaft journal.
Check wear and ovality of exhaust valve guide bushes and seats.
Check sensing element of thermostatic valves. Replace if necessary.
Disassemble "over speed trip" slide valve and replace seals
Remove and inspect gasket on valve carrier on oil pump suction side/ valve box
underttake inspection and cleaning of coolant side spaces of (a) Lub oil cooler
(b) Fresh water cooler
Check functioning of P2/P4 valve Repair/overhaul and renew fasteners if necessary. Check holding down bolts of all flanges and pipes connected to P2/P4 valve.
Inspect turbo super charger.
(a) Inspection of compensator joints for cracks. (b) Renewal of joints as necessary
Remove & replacement of air intake filters
(a) Inspection of condition of guard of air intake filters for deterioration/damage. (b) Renewal of huard as necessary
MAN ENERGY SOLUTIONS INDIA PRIVATE LIMITED
stage.html
html • 0.02 MB
finance_604322.pdf
boq_comp_chart.xlsx
xlsx
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .