GE(S)/M-58/2019-20

Amount

Taking down cement plaster, any description on brick, concrete or stone walls or ceiling including racking out joints, hacking for key, scrubbing down with water etc and removal of rubbish off all as specified and directed.

M&L for rendering 5 mm thick in CM 1:4 mixed with liquid water proofing compound @ 0.200 litre per bag of 50 kg of cement, over and including 10 mm thick rendering in CM 1:6 on brick work or concrete surfaces. Note:- Liquid water proofing compound shall be measured and paid for separately as “Supply only”

M&L for rendering 10 mm thick in CM 1:6 on brick work or concrete surfaces finished even and smooth without using extra cement.

M&L for rendering 5 mm thick in CM 1:3 on concrete surfaces in ceiling including finishing even and smooth without using extra cement.

M&L for preparation of new plastered or unplastered surfaces of walls and applying two coats of distemper oil emulsion, white or tinted, over and including a coat of 2 mm thick wall care putty all as directed.

M&L for preparation of newly plastered or unplastered surfaces of ceilings and applying three coats of white wash.

M&L for preparation of new plastered or unplastered surfaces of walls and applying two coats of cement base paint, white or tinted, over and including a coat of alkali-resistant priming paint all as directed.

M&L for complete removal of existing treatment from walls and applying two coats of distemper oil emulsion, white or tinted, over and including a coat of 2 mm thick wall care putty all as directed.

M&L for complete removal of existing treatment from walls and applying applying two coats of cement base paint, white or tinted, over a coat of alkali-resistant priming paint all as directed.

M&L for preparation of old plastered or unplastered surfaces of ceilings and applying two coats of white wash.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing from site and rubbish off the premises.

M&L for joint free non skid ceramic tiles, coloured, 7 to 8 mm thick (square/rectangular) in floors etc. area of each tile exc. 0.11 sqm but n. exc. 0.18 sqm, set & jointed in neat cement slurry & pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6.

M&L for joint free non skid ceramic tiles, coloured, 7 to 8 mm thick (square/rectangular) in floors etc. area of each tile exc. 0.18 sqm but n. exc. 0.38 sqm, set & jointed in neat cement slurry & pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6.

M&L for glazed ceramic tiles, coloured, 350x250x7mm/450x300x7mm thick on vertical surfaces such as skirtings, dados and risers to steps etc, set & jointed in neat cement slurry & pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 on brick or concrete surfaces.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exceeding 1.5 sqm each and removing from site. Note - Quoted rate shall be deemed to be include for cutting holes/demolition of PCC blocks etc for taking down chowkats and making good the damaged surfaces in CM 1:3 all as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exceeding 1.5 sqm but not exceeding 4 sqm each and removing from site. Note - Quoted rate shall be deemed to be include for cutting holes/demolition of PCC blocks etc for taking down chowkats and making good the damaged surfaces in CM 1:3 all as directed.

S&F pressed steel frames of size 125 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified.

S&F pressed steel frames of size 105 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified.

S&F pressed steel frames of size 75 x 50 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified.

M&L for 40 mm thick wire gauzed steel shutter made with MS hollow/rectangular tubes (80x30x3 mm) in styles/rails and grill of 10x10 mm square bars in wire mesh area only including two Nos. 150 mm long MS handles, two nos. 250 mm long MS sliding door bolts with locking arrangement, two Nos. 200 mm long MS tower bolts, fly proofing wire mesh fixing with screws, necessary welding for fixing door shutter to chowkats and builders hardware to shutter complete all as specified and as directed by Engineer-in-Charge. Note:- Wire mesh shall be measured and paid for separately.

S&F 35 mm thick factory made, second class hard wood, plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated with and including applying two coats of synthetic enamel paint over a coat of pink primer.

S&F 35 mm thick factory made second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc. sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24(a), supplied and fitted to chowkats with and including applying two coats of synthetic enamel paint over a coat of pink primer.

S&F solid PVC door frame of size 50mm x 47mm made out of 5 mm plain colour (Wenga/teak colour) PVC sheet reinforced with M.S. square tube, fixing in opening as per specification and drawing.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, and fixing in the frame at site as per specification & drawing.

S&F in repairs 18 mm thick PVC one side laminated board fixed with and incl hinges in kitchen cabnets and cup board shutters.

S&F box type steel windows comprised of tubular frame and shutters made out of 1.25 mm thick M S sheet tube factory made with double side shutters wire gauged shutter & glass glazed shutter (wire cloth and glass panes only shall be measured and paid seperately) with side hung shutters with steel handle and steel peg stay dovetailed or welded incl 2 Nos tower bolts 100 mm long for each leaf and 10 mm square bar grills at spacing as shown on drg welded to FI frame work, including other fittings, hinges, handles, tarred hold fasts, PCC blocks etc all as shown on drg No CEPZ/TD-354/09 sheet 1/3 to 3/3 complete all as specified and directed.

S&F sheet glass 3 mm thick, ordinary quality and glazing with oil putty or wooden beads supplied with shutters in square n. exc. 0.5 sqm in each pane.

S&F sheet glass 3 mm thick, figured glass, pin headed type and glazing with oil putty or wooden beads supplied with shutters in square n. exc. 0.5 sqm in each pane.

S&F stainless steel wire cloth, 0.36 nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples or wooden beads supplied with shutters.

S&F 200 mm long aluminium, anodized, barrel tower bolts of extruded section and fixed.

S&F 150 mm long aluminium, anodized, barrel tower bolts of extruded section and fixed.

S&F extruded aluminium alloy handles, fabricated type, anodized of size 150 mm.

S&F butt hinges, medium weight, cold rolled, mild steel of size 100 mm.

S&F 250 mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy.

S&F hasp and staple of size 100 mm, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws.

S&F in repairs 15 mm bore pillar taps, cast copper alloy with capstan heads, chromium plated, fancy type, screwed down high pressure with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe and fixed.

S&F in repais 15 mm bore bib taps, cast copper alloy, fancy type, chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule.

S&F in repairs 15 mm bore stop valve/angle valve, cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or for unions.

S&F in repairs 15 mm bore stop valve, fancy type, chromium plated with long shank and cup (concealed type), screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or for unions.

S&F in repairs brass chromium plated tubular towel rail, 20 mm dia, D type, 60 cm long between flanges.

S&F in repairs brass chromium plated shower rose of 125 mm size with swivel joint including fixing to steel pipe or union.

S&F in repairs 20 mm dia gun metal, globe or gate valve, with iron wheel head, screwed both ends for iron pipe.

S&F in repairs PVC valveless, syphonic action type, flushing cistern, low level, 10 litres capacity, white, with inlet, ball valve, float and handle including brackets and PVC flushing pipe, 32 mm dia.

S&F in repairs vitreous china wash basin, white, flat back, size 550x400mm including brackets, cutting for and pinning in ends of brackets or erecting stand, brass chromium plated perforated waste coupling/fittings 32 mm dia with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed and PVC waste pipe of 32mm bore and of suitable length, complete all as specified.

S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white, with and including plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, and fixed complete all as specified.

S&F in repairs CP pressure jet for EWC, with 1.50 m tube fixed to angular stop cock.

S&F in repairs sink with drainage board made of stainless steel 1.00mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915 mm x 460 mm, bowl size 410mm x 330 mm x 160 mm and PVC waste pipe of 32 mm bore and of suitable length, complete all as specified.

S&F in repairs stainless steel plate rack, 0.56 mm thick of standard pattern, of size 750x900mm of approved make complete.

S&F stainless steel grating doom 100 mm dia fixed with cement mortar in floors.

S&F stainless steel grating doom 100 mm dia with waste hole, fixed with cement mortar in floors.

S&F PVC connection 15 mm size with PTMT nuts of length 600 mm.

S&F in repairs 500 litres capacity rotational moulded polyethylene water storage tanks triple layer (cylindrical vertical with closed top), hoisted and fixed in position all as specified in SSR Part-I, connecting up pipes including 20 mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed. (Minimum weight 210 gms.)

Supply and laying in repairs 15 mm bore tubes, galvanized steel, medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors all as specified and directed.

Supply and laying in repairs 20 mm bore tubes, galvanized steel, medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors all as specified and directed.

S&F sheet glass corner shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long

S&F in repairs 20 mm bore drapery rod in any length, high strength MS pipe with 1 mm thick PVC wood grain coating including brackets and knobs all as directed by Engineer-in-Charge.

M&L for 18 to 20 mm thick marble work of marble green/ Bhaislana zebra (table rubbed and polished) in single piece in cooking platform, pillars, window-cills, jambs, steps and like in CM 1:4 over and including 15 mm thick screed in CM 1:6 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade over and including 15 mm thick screed in CM 1:4 including rounding edges.

M&L for 20 mm thick black granite (of any type) work(table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms including making hole and like in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite over and including 15 mm thick screed in CM 1:4 including rounding edges.

M&L for 75 mm thick PCC 1:3:6 type C1 using 20 mm graded stone aggregate in plinth protection. Concrete shall be laid in alternate bays n.exc 3 m in length finished fair and even including provision of joints of 6 mm wide and 10 mm deep along the wall and bays filled with bitumen mastic (1:3).

S&F in repairs cast iron floor trap, 75 mm dia of outlet, with grating including jointing to waste pipe fixed in cement concrete type B1(1:2:4).

S&F in repairs cast iron floor trap, 100 mm dia of outlet, with grating including jointing to waste pipe fixed in cement concrete type B1(1:2:4).

S&F salt glazed stoneware gully traps of size 150x150 mm, square or round mouthed, type ‘P’.

S&F in repairs 100 mm bore cast iron, sand cast, soil, waste and vent pipes, in any length with or without ears, with cement joints, fixed to walls.

S&F in repairs 100 mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) with oval access door.

S&F in repairs 75 mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) with oval access door.

S&F in repairs 75 mm bore cast iron, sand cast, soil, waste and vent pipes, in any length with or without ears, with cement joints, fixed to walls.

S&F 75 mm bore CI cowl.

S&F stack clamps, for 100 mm bore pipe, out of 50x5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof.

S&F stack clamps, for 75 mm bore pipe, out of 50x5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof.

Demolition of cement concrete (reinforced) (reinforcement cut as required to facilitate demolition) roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work and removing from site all as specified and directed.

M&L for form work to flat, rough finished surfaces of concrete of chullah hoods, chajjas, troughs and similar items including edges.

M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia.

M&L for RCC 1:2:4 (Nominal mix) type B-1 using 20 mm graded stone aggregate in in chajjas.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for (roof padding) and removing from site all as specified and directed.

M&L for 25 mm thick (average) cement concrete 1:2:4 type B-0 mix (12.5 mm graded stone aggregate) in padding over roof.

M&L for 10 mm thick rendering in CM 1:4 over concrete surfaces (Roof) mixed with liquid water proofing compound @ 0.200 litre per bag of 50 kg of cement complete all as specified. NOTE : Liquid water proofing compound shall be measured and paid for separately as “Supply only”

M&L for applying roof treatment on top of roof with APP modified membrane (minimum 3 mm thick) weight not less than 3 Kg/sqm and reinforced with non-woven polyster reinforcement/mat (centre core) with thermal insulation with white mineral gravel finish on upper side of membrane laid by torch application method with overlaps 150 mm on length side and 100 mm on the width side as per manufacturer’s instructions over a coat of approved cold applied bituminous oil based primer (IS- 3384) @ 250 gm/sqm complete all as specified and as directed by Engineer-in-Charge.

M&L for 40 mm thick brick tiles laid over and including 15 mm thick screed bed in CM 1:6 and joints grouted in CM 1:3 mixed with 5% of crude oil by weight of cement laid on APP membrane complete all as specified and as directed by Engineer-in-Charge.

Supply only liquid water proofing compound.

M&L for PCC 1:3:6 type C-0 using 12.5 mm graded stone aggregate in cills, steps, bands, copings, bed plates, blocks for inserting hold fasts, filling back of chowkats etc. and the like including weathering, slightly rounded or chamfered angles and throating as directed.

M&L for preparation of new or previously untreated steel surfaces of any description, over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc. and removing from site all as specified and directed.

Brick work with fly ash bricks, old size bricks, straight or curved on plan exc 6 mtr mean radius built in CM (1:4) all as specified and directed.

M&L for 75 mm thick cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate in sub base.

S&F 60 mm thick, M-35 grade, coloured (red/yellow) glossy finish, machine pressed PCC interlocking paver block, with grey cement and pigment, any shape and size laid dry over and including 50 mm thick screened river washed sand cushion.

M&L for PCC 1:2:4 type B1 using 20 mm stone aggregate in kerbs of interlocking tiles and the like as directed.

M&L for providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sqm of the vertical surface of the sub-structure to a depth of 300 mm including excavating channel along the wall and rodding etc. complete.

M&L for providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall below concrete or masonry apron using chemical emulsion at the rate of 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete.

M&L for providing and injecting chemical emulsion for Post Constructional Antitermite Treatment of soil under existing floors using emulsion at the rate of 1.00 litre per hole, 300 mm apart including drilling and plugging 12 mm dia holes with cement mortar 1:2 to match the existing floors.

M&L for providing and injecting chemical emulsion for Post Constructional Antitermite Treatment of voids in masonry using chemical emulsion one litre per hole, at 300 mm intervals including drilling holes at 45 degree and replugging them with cement mortar 1:2 to match the existing floors.

Excavating in trenches in any type of soil, n. exc. 1.5 m wide and n. exc. 1.5 m in depth, for foundation, etc. or for shafts, wells, cess pits, manholes, pier holes, etc n. exc. 10 sqm on plan and n.exc 1.5 m in depth and getting out.

All as per item No. 92.00 above but exc. 1.5 m and n. exc. 3 m deep.

M&L for cement concrete (1:4:8) type D2 using 40 mm graded stone aggregates as in foundation, filling and mass concrete all as specified and directed.

Brick work with fly ash bricks, old size bricks, straight or curved on plan exc 6 mtr mean radius built in CM (1:6) all as specified and directed.

M&L for rendering 15 mm thick in CM 1:4 on brick work or concrete surfaces finished even and smooth without using extra cement.

M&L for preparation of newly plastered or unplastered surfaces of walls and applying three coats of white wash.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement including forms, moulds mitered/stopped ends, etc all as specified.

M&L for PCC 1:2:4 type B1 using 20 mm stone aggregate in lintels up to 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed.

M&L for precast reinforced cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate in landings, cover slabs (for manholes etc.) chullah hoods, chajjas, shelves and similar articles with plain faces, set in CM 1:4, including necessary form work moulds etc all as specified. (Reinforcement shall be measured and paid for separately).

M&L for mild steel TMT bars 6 mm to 8 mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia.

Removing excavated material (soil) n.exc. 50 m and depositing where directed at a level n. exc. 1.5 m above the starting point.

S&F 80 mm thick, M-40 grade, coloured (red/yellow) glossy finish, machine pressed PCC interlocking paver block, with grey cement and pigment, any shape and size laid dry over and including 50 mm thick screened river washed sand cushion.

M&L for form work to sides of flat, rough finished surfaces of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work; vertical to batter.

M&L for form work to sides and soffits of flat, rough finished surfaces of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc.

M&L for form work to sides of square, rectangular or polygonal, rough finished surfaces of concrete of pillars, posts, struts, piers, columns and stanchions.

M&L for RCC M-25 (design mix) using 20 mm graded stone aggregate in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc. basement slabs and mass concrete.

M&L for RCC M-25 (design mix) using 20 mm graded stone aggregate in beams, cantilevers, bressumers, lintels.

M&L for RCC M-25 (design mix) using 20 mm graded stone aggregate in columns, pillars, piers, posts and struts.

M&L for mild steel TMT bars 5 mm dia and over up to and including 10 mm dia in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia.

Returning, filling in (soil), including spreading, leveling, watering and well ramming in layers not exc. 25 cm.

Taking down steel gate of any type and size and refixing the same at same location after carrying out necessary repair/alteration by means of welding, greasing etc. including two coats of synthetic enamel paint all as specified and directed by Engineer-in-Charge.

Roughening surface of old concrete by picking, sweeping clean and washing down with water to remove all loose dust etc

M&L for vitrified ceramic light shade tiles 10 mm thick(square/rectangular) polished, area of each tile n. exc.0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layer in CM 1:6.

Excavating in post holes, in any type of soil, (or similar holes) each n. exc. 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n. exc. 25cm, watering and removing surplus soil to a distance n. exc. 50m and making good surfaces.

S&F rolled mild steel of grade Fe-290 (Grade E-165) in joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20 mm of length indicated)

S&F rolled mild steel of grade Fe-290 (Grade E-165) quality ‘A’ in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.

S&F pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 MPa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

M&L for cement concrete (1:3:6) type C-2 using 40 mm graded stone aggregates as in foundation, filling and mass concrete/sunken floors all as specified and directed.

Taking down carefully aluminium/copper point wiring (light, fan, socket or power) complete, including fixtures and fittings such as switches, ceiling roses, pendent, regulators, sockets, bell push, bell, light fittings etc. removing materials to store for keeping in safe custody or for taking credit (Credit shall be made as per Schedule of credit), removing rubbish from the site and making good all disturbed surfaces of walls, floors etc. to match to the existing surfaces.

M&L for modular point wiring complete with 1.5 Sq mm single core PVC insulated but unsheathed multistranded copper conductor FRLS cable 1100 volts grade drawn through and including non metallic rigid PVC heavy duty concealed conduit with wall thickness not less than 1.8 mm including conduit accessories like bends, tees junction boxes, etc fixed concealed/recessed in wall or ceiling etc including 1.5 Sq mm, single core, PVC insulated but unsheathed multi stranded copper conductor FRLS cable 1100 Volts grade as earth continuity wire connected to earth dolly including inner and outer frame plate matching with surrouding with modular sunken steel boxes zinc oxide plated of suitable size including modular sheets of suitable module and back plates etc. complete for:- (a) One light/fan point controlled by one, one way switch. Make of cable - Polycab, L&T, Havells, RR (Unilay)

All as per item No. 121.00 above but one bell buzzer point controlled by one, bell push switch 5A.

All as per item No. 121.00 above but one light point controlled by two, 2 way switches.

All as per item No. 121.00 above but one 3 pin 5 or 6 Amps socket outlet on independent board with other switches as directed.

All as per item No. 121.00 above but one 3 pin 5 or 6 Amps socket outlet on same board with other switches as directed.

M&L for modular point wiring complete with 2.5 Sq mm single core PVC insulated but unsheathed multistranded copper conductor FRLS cable 1100 volts grade drawn through and including non metallic rigid PVC heavy duty concealed conduit with wall thickness not less than 1.8 mm including conduit accessories like bends, tees junction boxes, etc fixed concealed/recessed in wall or ceiling etc including 2.5 Sq mm, single core, PVC insulated but unsheathed multi stranded copper conductor FRLS cable 1100 Volts grade as earth continuity wire connected to earth dolly including inner and outer frame plate matching with surrouding with modular sunken steel boxes zinc oxide plated of suitable size including modular sheets of suitable module and back plates etc. complete for one 3 pin 15 or 16 Amps socket outlet on independent board. Make of cable - Polycab, L&T, Havells, RR (Unilay)

S&F modular switch 1 way 6 Amp, 1 module complete all as specified and directed. Make: Crab tree Murano/Legrand ARTEOR series/GM cassiviva/SSK (Elegance)/Anchor (Roma)/Indo Asian (Glit)

S&F modular switch 2 way 6 Amp, 1 module complete all as specified and directed. Make: Crab tree Murano/Legrand ARTEOR series/GM cassiviva

S&F modular switch 1 way 16 Amp, 1 module complete all as specified and directed. Make: Crab tree Murano/Legrand ARTEOR series/GM cassiviva/SSK (Elegance)/Anchor (Roma)/Indo Asian (Glit)

S&F modular socket 6 Amp, 2/3 pin mutipurpose 2 module complete all as specified and directed. Make: Crab tree Murano/Legrand ARTEOR series/GM cassiviva/SSK (Elegance)/Anchor (Roma)/Indo Asian (Glit)

S&F modular socket 6 Amp/16 Amp, 6 pin multi purpose 2 module complete all as specified and directed. Make: Crab tree Murano/Legrand ARTEOR series/GM cassiviva/SSK (Elegance)/Anchor (Roma)/Indo Asian (Glit)

S&F modular fan step regulator , 120W, 2 module, hum free and connecting electrically all as specified and directed by Engineer-in-Charge. Make: Crab tree Murano/Legrand ARTEOR series/GM cassiviva/SSK (Elegance)/Anchor (Roma)/Indo Asian (Glit)

S&F modular bell push, 6 Amps, 1 module complete all as specified and directed. Make: Crab tree Murano/Legrand ARTEOR series/GM cassiviva.

S&F bell electric heavy duty Ding Dong type 230 volts single pole all as specified and directed by Engineer-in-Charge. Make - SSK (Topline)/Leader/Anchor

S&F lamp holder insulated body with back plate for batten fittings polycarbonate body all as specified and directed by Engineer-in-Charge. Make - GM/Cona/Leader

S&F ceiling rose surface bakelite 3 terminals 230 Volts AC with polycarbonate body all as specified and directed by Engineer-in-Charge. Make - GM/Cona/Leader

S&F exhaust fan, heavy duty, AC single phase 300 mm sweep complete with louvers including fixing/grouting of frame in wall opening complete & connecting with & including 3 core PVC insulated copper conductor flexible cable of size 23/0.0076 (or eq. Size in mm) from ceiling rose to fan. Make - Havells/Bajaj/CG

M&L for in repairs sub main wiring with two runs of PVC insulated but unsheathed multi stranded copper conductor FRLS cable 1100 volt grade of size 6 Sqmm and one run of 6 Sqmm single core PVC insulated but unsheathed multi stranded copper conductor FRLS cable 1100 volt grade as earth lead drawn through in and including non metallic PVC conduit of size 25 mm dia (external) with wall thickness not less than 1.8 mm, ISI marked concealed in wall including accessories like bends, tees junction boxes, etc fixed in wall or ceiling etc. complete as directed by Engineer-in-Charge. NOTE: Two runs of cable with one run of earth wire and PVC conduit shall be measured & paid for as one length. Make of cable - Polycab, L&T, Havells, RR (Unilay)

S&F surface mounted 1x20 watt LED tube light fittings (4 feet long), prewired, decorative luminaire with inbuilt LED tube rod and acrylic cover with all accessories and making connection using 3 core, 0.50 Sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose/PVC connector to light fitting and testing etc complete all as specified and directed. Make :- Philips/Crompton/Hanger

S&F surface mounted 1x10 watt LED tube light fittings, prewired, decorative luminaire with inbuilt LED tube rod and acrylic cover with all accessories and making connection using 3 core, 0.50 Sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose/PVC connector to light fitting and testing etc complete all as specified and directed. Make :- Philips/Crompton/Hanger

S&F bulk head 10 W LED light fitting IP 43 in engineering plastic housing with clear primatic diffuser conf to Cat Pt No. CG80IB10WLED of C&G or equivalent of make - Philips/Wipro/Bajaj compete with all acessories, connecting electricaly to ceiling rose using cord flexible 3 corp PVC insulated over all sheathed with flexible copper conductor of size 0.75 sqmm all as required.

S&F in repairs and testing factory made sheet metal enclosure disribution board for MCCB as incomer and MCB as outgoing 415 volts 3 phase 50 C/s 4 way with double door, IP - 43 protection IK-09 complete with appropriate size copper bus bar and neutral link duly fixed/concealed in wall complete and making good disturbed surfaces of wall, floor etc including necessary connection lugging with copper lugs pin/ring type all as directed by Engineer-in-Charge as per Cat Part No. 607770 of Make- Legrand or equivalent of Make : Hager/L&T/INDOASIAN/Schneider complete with one MCCB 3 pole 415 Volts 63 Amps rating with rupturing cap 16 KA of the same make as of distribution board & including cutting chases to wall for fixing DB and making good the disturbed wall surface all as required at site or directed by Engr-in-Charge (Outgoing MCB will be measured separately)..

S&F in repairs and testing factory made sheet metal enclosure for MCB DB SPN 8 way 240 volt with double door, IP - 43 protection duly fixed/concealed in wall complete and making good disturbed surfaces of wall, floor etc including necessary connection lugging with copper lugs pin/ring type all as directed by Engineer-in-Charge as per Cat Part No. 607712 of Make Legrand or equivalent of Make : Legrand/ INDOASIAN/L&T/Hager.

S&F building security light luminaire 25 W LED 5000 K AC 230 volts, new generation saving & enviormental friendly long life versatile pressure die cast aluminium luminaries with high power LED as light source complete making connection with street light/building security light box or OH line using PVC insulted and sheathed single core multi stranded copper conductor cable of size 1.5 Sqmm including suitable size of bracket and light grade pipe for muntaining of fitting all as specified and directed by Engr-in-Charge (Make : Crompton Cat Part No. LSTS-25-CDL or equivalent of Make - Philips/Hager).

S&F in repairs single pole and neutral enclosure with two pin and earth plug socket complete with one single pole MCB 20 Amp ‘C’ curve type, 230 volts, 10 KA.

S&F in repairs MCB single pole 230 volts any rating from 6 to 40 amps, with rupturing capacity 10 KA, 'C' curve type, including providing thimble for out going cables all as per Cat Part No NCN106N/NCN140N of Make - Hager or equivalent of Make- Legrand/Indo Asian/L&T

S&F in repairs MCB single pole and neutral 240 volts any rating from 6 to 32 amps, with rupturing capacity 10 KA, 'C' curve type, including providing thimble for out going cables all as per Cat Pt No NCN206N/NCN232N of Make- Hager or equivalent of make - Legrand/Indo Asian/L&T

M&L for in repairs earthing complete with galvanised steel earth electrode 60cmx60cmx6mm buried directly in ground vertically to depth not less than 2.25m below normal ground level with top edge of the earth plate at a depth not less than 1.5m below ground level connected to and including GI earth lead wire 4 mm dia by means of nuts, bolts, check nuts and washer etc, made of GI and connected to test point and earth dolly all as shown in electrical plate No. 3 SSR Part-I 2009 and specified or indicated including excavation and earthwork in any type of soil PCC (1:3:6) Type C1 in chamber, precast RCC 50 mm thick in cement concrete (1:2:4) type B1, reinforced with welded steel wire fabric or XPM (Weight not less than 4.00 Kg/Square metre) with cast iron frame, funnel with wire mesh, 20mm bore medium grade GI watering pipe, lugs, 15mm bore medium grade GI protection pipe, test point etc. complete all as specified and directed. Note:- (i) Item includes the cost of 7.5 metre GI pipe for protection of earth lead. (ii) Item includes the cost of 7.5 metre GI earth lead.

M&L for taking down ceiling fan and hanging the same after repair and connecting up including provision of cable from ceiling rose or connector to fan.

S&F LED lamp 12 watts

Supply and lay in trenches/on wall/on pole/in duct /through protection pipe, XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables heavy duty LT cable, 1100 volts grade with aluminium conductor cross sectional area 16 Sqmm 4 core size including retrieving/taking out/taking down old unserviceable cable from duct/trenches/pipes/pole/wall etc. including brick cover and protection pipe and disconnecting the connections.. Make: Havells/Polycab/CCI/Rallison Note:- Excavation and earth work, sand cushioning, brick cover and protection pipe etc. shall be measured and paid for separately.

M&L for dry clean fine river sand as in sand cushioning to underground cable including punning down of sand layer all as specified and directed. Note :- Punned thickness shall only be measured and paid.

M&L for brick protection with sub class 'B' old size brick well burnt laid flat for cable protection abutting each other laid dry with width equal to length of brick complete all as specified and directed.

M&L for galvanised steel tubing, light grade, for protection of cable, laid in trenches/road crossing/floor or fixed to pole/wall with all fittings, of size 40 mm bore.

Raghbir chand

dadwal engineers

M/S CANTILEVER ENGINEERS

M/S J N TRADERS