SPECIAL REPAIR TO BLDG NO P-96 (GUARD ROOM), STONE PATHWAY AND CERTAIN OTHER SANCTION WORKS UNDER GE (NORTH) AHMEDNAGAR

Amount

Demolition of cement concrete (un-reinforced) in ground floor & paving n.exc. 15cm thick below or above ground level.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified.

M/L for providing 75mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregate as in sub base complete all as directed.

M & L moorum filling in floors or paving laid in layers n.exc. 15 cm thick spread leveled and rammed including watering complete all as specified and directed

M & L hard core of gauge etc. 63 mm but n. exc. 100 mm deposited spread and leveled in layers n. exc. 15cm thick water and rammed etc. Complete all as specified and directed.

M&L for RCC Type B-1 1:2:4 using 20 mm graded aggregates as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc. basement slabs, under-reamed piles and mass concrete and floor slab.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips (Note :- including driling Inserting and welding new TMT bar with existing TMT bars of beam)

Material and labour for 60 mm thick, PCC pavers interlocking tiles of glossy finish, with grey cement and no pigment ,any shape & size conforming to IS 15658 of 2006. M-35 grade made up with 12.5mm graded mechanically crushed stone aggregates, factory made over and incl 30mm thick sand cushioning and joints filled with fine sand incl leveled with plate vibrator & sweeping etc complete all as specified and directed.

M&L for coloured glazed ceramic tiles digitally printed 300x450mm, 7-8 mm thick as approved by GE as in dado / skirting or on vertical surfaces, over and including 10 mm thick backing coat in CM (1:4) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile etc complete all as specified and directed.

Material and labour for joint free / rectified anti skid ceramic coloured tiles 7-8mm thick matching to dado tiles area of each tile 400x400mm , as in floor etc laid over and including screed bed 15 mm thick in cement mortar 1:6 set and jointed with white or coloured cement to match complete all as specified and as directed.

M&L for joint free / rectified anti skid ceramic coloured tiles 8-10 mm thick as approved by GE (square /rectangular) area of each tile 600x600mm, as in floor etc laid over and including screed bed 15 mm thick in cement and sand mortar (1:6 ) set and jointed with white or coloured cement to match the shade of tile etc complete all as specified and as directed

M&L in repairs for 15mm to 18mm thick pre-polished granite stone slab of approved shade and color Jet Black / Telephone Black as in top table, top of WHB, kitchen slab/platform, steps, gate pillars, cills, jambs etc or on vertical surfaces including vertical projection, full round molding the edge including 10 mm thick backing coat in CM (1:3) jointing & pointing in white cement (1:2 ) using marble dust with admixture of pigment to match the shade of granite rubbing including dismantling etc complete all as specified and directed by Engineer-in-Charge

Material and Labour for 75mm thick plain cement concrete type C-1 (1:3:6) using 20 mm graded stone aggregate as in plinth protections & path, complete all as specified

Demolition of brickwork or stone bouilder masonary built in cement mortar or lime mortar complete all as specified

M&L for brickwork with fly ash bricks straight or curved on plan exc 6m mean radius,built in CM 1: 6 complete all as specified

M&L for brickwork with fly ash bricks straight or curved on plan exc 6m mean radius,built in CM 1: 6 complete all as specified

Taking down cement mortar plaster on brick or stone walls, raking out joints, hacking for key complete all as directed

M&L for rendering, 10 mm thick on brick / concrete surfaces in cement mortar 1:6 surfaces finished even and smooth without using extra cement including sagol finished complete all as specified.

M&L for rendering, 15 mm thick on stone/brick / concrete surfaces in cement mortar 1:4 finished even and fair without using extra cement complete all as specified and directed.

M&L for rendering 5mm thick on concrete surface of ceiling in CM 1:3 finished even and fair without using extra cement complete all as specified and directed.

M&L for welding in repairs, thickness of metal to be welded exc 6 mm but n exc 9mm

Supply only concrete bonding (FOSROC Nito bond EP) compound.

S&F GI wire netting 0.90mm dia and 12mm mesh lathing to wood or metal studding, joists, etc. in walls, ceilings, stanchions, beams, etc. including all laps, cutting and waste

M&L for rendering 15mm thick in CM 1:3 on fair faces of concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M & L for preparation of newly plastered surface of wall and apply two coats of OBD over a coat of primer any height including scaffholding etc complete all as directed.

M&L for preparation of new plastered treated surfaces of walls by brooming down and and applying two coats of weather proof 100 % acrylic exterior emulsion apex ultima paint over a coat of any tint as approved by GE after cleaning the surfaces complete all as specified and as directed.

M&L for preparation of old plastered treated surfaces of walls by brooming down and and applying one coat of weather proof 100 % acrylic exterior emulsion apex ultima paint of any tint as approved by GE after cleaning the surfaces complete all as specified and as directed.

M & L for preparation of newly plastered surface of ceiling and apply three coats of white wash any height including scaffholding etc complete all as directed.

All as per item No 28 (here-in-before) but on ceiling.

M & L for preparing old plastered surfaces of walls and apply one coat of OBD, finished with roller finish on plastered surfaces of wall any height including scaffholding etc complete all as specified and directed

M&L for 1 mm thick wall care putty etc complete all as specified and directed

S&F fix in repairs wash hand basin vitreous China white , flat back or angle type of size 500 X 400 mm incl pillar tap 15mm dia CP, waste chain and plug and porcelain stopper , waste pipe, a pair of brackets, or erecting stand and PVC connection etc complete all as specified and directed by Engineer-in-Charge

S&F in repairs vitreous China white squatting pan, Orissa pattern of size 580 X 440 mm width with integral foot rest set in cement concrete including flush pipe and connecting to trap / flushing cistern etc complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 10 ltr capacity PVC valve less, symphonic action type, flushing cistern, low level, all accessories etc complete all as specified and directed by Engineer-in-Charge.

Taking up or down 15 mm bore steel tubing and connections

Ditto all as per item No 35 above but 20 mm bore tubing

Ditto all as per item No 35 above but 25 mm bore tubing

Supplying and laying 16 mm dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including all fittings complete all as specified.

Ditto all as per item No 38 above but 20 mm bore tubing

Ditto all as per item No 38 above but 25 mm bore tubing

S & F in repairs PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified.

S&F in repairs stop cock/ anglecock/ two waycock cast copper alloy, Chromium plated fancy type screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union and fix of size 15 mm bore etc complete all as specified and directed by Engineer-in-Charge

Supply and fixing in repairs tubular towel rail, brass chromium plated 20 mm dia `D' type, 60 cm long between flanges including a pair of brackets all as directed.

S&F in repairs bib tap, 15 mm dia, CP cast copper alloy with crutch or butterfly handle screwed down for iron pipe or for brass ferrule etc complete all as specified and directed by Engineer-in-Charge.

S&F in repairs fancy type twin (Two way) bib tap, 15 mm dia, CP cast copper alloy with crutch or butterfly handle screwed down for iron pipe or for brass ferrule etc complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 15 mm dia pillar tap, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with long screwed shanks and fly-nuts, screwed for iron pipe all as directed.

S & F in repairs PVC flexible 32 mm Waste pipe for WHB, Sink etc complete all as specified.

S&F Vitreous China urinal, Half satll type, white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe andwaste pipe)

S&F in repair PVC (SWR) 110mm bore (dia) soil, waste and vent Pipe, (ISI Marked), in any length with rubber ring Joints fixed to wall with necessary stay clamps/ laid in trenches/floor etc complete all as specifed and directed.

.-Ditto- but As in trenches or floor

S&F in repair PVC (SWR) 75mm bore (dia) soil, waste and vent Pipe, (ISI Marked), in any length with rubber ring Joints fixed to wall with necessary stay clamps/ laid in trenches/floor etc complete all as specifed and directed.

.-Ditto- but As in trenches or floor

S&F PVC (SWR) 110 mm bore (dia), Bends any type, etc. and Jointing with Solvent Cement, complete all as specified and as directed

S&F PVC (SWR) 75mm bore (dia), Bends any type, etc. and Jointing with Solvent Cement, complete all as specified and as directed

S&F PVC (SWR) junction single, (Single T) equal or un equal 110mm bore

S&F PVC (SWR) junction single, (Single T) equal or un equal 75mm bore

S&F PVC (SWR) vent cowl110mm bore

S&F rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of 1000 litres capacity, triple layered, hoisted and fixed in position including 20 mm dia ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed to iron pipe, tank nipple and connected complete all as directed.

S&F in repair 20mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball and high density plastic ball screwed to iron pipe, tank nipple and connected (Minimum weight 15mm-142Gms/20mm-210Gms) complete all as directed.

Cutting chases in brick/ block wall, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth

Taking down chowkhats or frames not exc. 1.5 Sqm each with shutters (without taking off shutters from the frames) etc complete all as specified and directed by Engineer-in-Charge

Taking down chowkhats or frames exc. 1.5 sq. m and n exc 4.00 Sqm each with shutters (without taking off shutters from the frames) etc complete all as specified and directed by Engineer-in-Charge

Taking down shutters of any description exc 1 Sqm but n exc 2 Sqm each etc complete all as specified and directed by Engineer-in-Charge

S & F Pressed steel door frame of size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hings, lock strike plate, etc, complete all as specified,

S & F pressed steel door frame of size 100 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, complete all as specified,

S&F 35 mm thick IInd C/L H/W glazed & skeleton shutters open rebated and prepared to receive glass gauge, divided into square or rectangles with plain chamfered or rounded mitered & rebated slash bars including beads mitered for securing glass wire gauge etc all as specified

M&L for 35 mm thick plain framed, paneled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial plywood. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated

S&F Solid PVC Door frame size 50mm x 47 mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing

S&F factory made solid PVC moulded Door shutter with particle board core, 28 to 30mm thick (stiles) with 2,4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back space, supplying and fixing in frame at site as per specification & drawing.

S&F powder coated aluminium anodised aluminium frame, shutters for door,windows, ventilators with one or more rebates including joining cleat for fixing etc, rubber / neoprene beading and locking arrangement etc complete all as specified and directed by Engr-in-Charge

S&F anodised aluminium door shutters,aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges,anodised aluminum snap beading screws etc. complete all as specified

S&F anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified

S&F butt hinges medium weight cold rolled mils steel 100mm long.

S&F aluminium anodised barrel tower bolts of extruded section 150mm long.

S&F aluminium anodised handle of extruded section 150mm long.

S&F aluminium alloy, anodised, sliding door bolt with hasp, staple and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy 300mm long.

S&F 300 mm mild steel ordinary rat tail rod pattern door spring including roller and roller plate complete all as specified and directed.

S & F Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40 mm and fixed in any position any type of opening with and including wooden beads complete all as directed by Engr-in-Charge.

S&F 150mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring.

Hacking out old broken glass ( any thickness size ,quality or description ) from wooden/Steel frames glazed with putty or fixed with beads.

M & L for 3 mm thick sheet frosted/pin headed glass ordinary quality and glazing with oil putty or wooden beads in squares n.exc 0.50 sqm in each pane.

M & L for preparation of new wooden surface and applying two coats of synthetic enamel paint over a coat of pink primer complete all as directed.

M & L for preparation of old wooden surface and applying one coat of synthetic enamel paint.

M & L for preparation of old steel surface and applying one coat of synthetic enamel paint.

Material and labour for providing water proofing treatment on roofs, as per manufecturer's instructions and as specified after taking down/out as existing at site :- (a) Cleaning the newly plastered surfaces with wire brushes and applying a coat of bituminous primer @ 0.30 ltrs/sqmts and allow to dry.(b) Applying and laying torch APP polymer modified bituminous membrance 3 mm thick with non woven polyster matt as reinforced weighing not less than 3 kg/sqmts by thermofusion process as per manufacturers specification including applying one coat of aluminium paint. Make : Super Thermolay of STP / Equivalent in Dr Fixit, FosRoc. Note : (i) Work has to be carried out strictly by the authonticated applicator of the manufacturer and as per manufacturers specification as approved by GE. (ii) Certificate from manufacturer shall be submitted by the contractor. (iii) Including taking down of old APP Membrane.

M&L for rendering 10mm thick in CM 1:4 over concrete surfaces finished even and smooth including water proofing compound as per manufacturers instructions.

M&L Providing cement concrete Type C1 1:3:6 20mm graded aggregate) in kerbs or mud stops, rounded or chamfered on edges

Supply only polymer based lilquid water proofing compound.

S & F in repairs looking mirror of size 600 mm x 450 mm etc complete all as specified and directed by Engineer-in-Charge.

S&F curtain rod 25mm dia, having corrugated PVC extrusion on eletric resistance welded MS pipe with fancy type 02 nos Knobs and 02 Nos brackets per each door/ windows etc complete all as specified and directed

S&F PVC (SWR) Nahani /Floor trap, 75 mm dia of out let, plain with grating including jointing to waste pipe with solvent cement.

M&L Cutting out bricks, forming toothing for, and bonding new into old work including value of new materials entering old walls and jointing and pointing (measured on vertical face in contact with old wall only), in cement mortar 1:6

Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates

Excavating over areas, n exc 1.5m deep and getting out in soft/loose soil

M&L for Sand filling under floors or in foundation including watering and consolidation

M&L for Hardcore of Broken stone or boulders of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface

M&L for PCC 1:2:4 Type B2 (40 mm graded stone aggregate) in floors

M&L for Stone sett flooring with stone setts of size 200 to 250mm long, 150 to 200mm wide the 150mm deep and sides dressed; bedded in cement mortar 1:3, 20mm thick; joints grouted in cement mortar 1:2 with an admixture of metallic floor hardner, 5% by weight of cement and struck flush

M&L for Edge stones to flooring with stone setts of size 250 to 300mm long x150 to 200mm wide, and 450mm deep and ditto

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15m thick, spread, levelled, and blinded with earth and rammed including watering

Providing and laying Cement concrete work in pavement/hard-standing of flexural strength 40 kg/per square centimetre in field using 400 kg of cement per cubic metre, thickness of concrete 25 cm or less

M&L for Plain Cement concrete 1:4:8 Type D-2 (40 mm graded stone aggregate) in foundations, filling and mass-concrete

Rendering 10 mm thick on fair faces of brick work in CM 1:4 and finished even and smooth without using extra cements

Preparation of newly plastered surfaces and appling two coats of cement base paint over a coat of primer

Taking down carefully copper/aluminum point wiring (light/fan/bell/socket, power point etc) complete , including fixture and fitting such as switches, ceilling roses, pendants, regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per condition seperately) and making good disturbed surfases of walls, floors etc complete all as specified and directed Engineer-in-Chage

M&L for point wiring complete on surface of wall (open) type with two runs of 1.5 sq mm for phase and neutral single core multistranded copper conductor of 1100 volts grade PVC insulated and unsheathed FRLSH cable drawn in and incl PVC Casing and capping ISI Marked with its accessories with provn of Acrylic plate and fixed with brass screws cup washer for fixing switches/socket/regulators etc incl 1.5 sq mm single core multistranded copper conductor of 1100 volts grade PVC insulated and unsheathed FRLSH cable as Earth continuity conductor to common earth & connecting to earth dolly for the following, all as specified and directed. Note : 1. Proper colour coding shall be adopted for wiring (For Phase- Red, Yellow, Blue, For Earth - Green and For Neutral- Black) 2. All points are required to earthed upto fixtures i.e. Holders, Tube lights, Wall lights, bulkhead lights, bldg security light etc

One light point controlled by switch 5 Amp single pole one way

S&F switch piano flush type single pole, one way 5/6 Amp etc complete all as specified and directed by Engineer-in-Charge

S&F Socket, 6 Amp,3 Pin 230V AC etc complete all as specified and directed by Engineer-in-Charge.

One 3 pin 5 Amp socket outlet on same board controlled by one, one way 5 Amp switch

One socket outlet 5/3 pin 5 Amp controlled by one switch on independent board

All as per Item No 106 (here-in-before) but with 2.5 Sqmm Copper conductor cable for Phase , Neutral and Earth for one 3 pin, 15 Amp socket outlet on independent board

S &F Switch piano, flush type single pole, one way 15/16 Amp etc complete all as specified and directed by Engineer-in-charge

S & F Socket outlet 6/3 pin, 15/16 Amp, flush type etc complete all as specified and directed by Engineer-in-charg

S & F electronic dimmers,as per existing wattage, 240V f lush type on the exiting phenolic laminated sheet etc. as required etc complete all as specified and directed by Engineer-in-Charge

Supply & fixing lamp holder (Angular/Straight ), insulated body, with back plate for batten fitting etc complete all as specified and directed by Engineer-in-Charge

M&L ceiling rose 3 terminal / PVC / polycarbonate, isolated body etc complete all as specified and directed by Engineer-in-Charge .

S & F in replacement double door Sheet metal enclosures factory made DBs SPN, 8 way ,240 volts ,protection class IP-42, suitable for fixing of MCBs, Isolators etc, confirming As per IEC 61439-3 ,Suitable for Flush Mounting and Surface Mounting, With 100 A Copper Busbar ,With Neutral bar, Earthbar and Cable ties for Cable management,Fully shrouded Neutral bars, Prefitted masking sheet complete all as specified and as directed.

Supply & fixing MCBs, SPN, AC, 240 volts of 40 Amps capacity 16 KA, 'C' series and making connections with suitable size of copper lugs etc complete all as specified and directed by Engineer-in-Charge.

Supply & fixing MCBs, SPN, AC, 240 volts of 63 Amps capacity 16 KA, 'C' series and making connections with suitable size of copper lugs etc complete all as specified and directed by Engineer-in-Charge

Supply & fixing MCBs, SP, AC, 240 volts of 06-40 Amps capacity 16KA, 'C' series and making connections with suitable size of copper lugs etc complete all as specified and directed by Engineer-in-Charge

Supply & fix Lumeno Inverter LED Bulb 9 Watt (cool day light) having colour temp 6500 K and lumen output 950 Power back up upto 4 Hrs Charging Time 8-10 hrs over charging protection suitable for "B-22 type to fix on batten holder and wall light etc complete all as specified and directed by Engineer-in-Charge

Supply and fix Decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack LED Tube light fitiing 20 Watt with LED light source 6500 K with uniform light output, with all accessories including its connection with and including 2 core sheathed copper conductor cable of size 0.5 Sqmm with complete with all accessories etc complete all as specified and directed by Engineer-in-Charge

S&F Decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack LED Tube light fitiing 10 Watt with LED light source 6500 K with uniform light output, with all accessories including its connection with 2 core seathed copper conductor cable of size 0.5 Sqmm with etc complete all as specified and directed by Engineer-in-Charge .

Supply & fix in replacement energy saving and environmental friendly long life LED street light 25 Watt (Bldg security light) made up of pressure die cast aluminium housing with mild power LED as lighting source and PC cover having TOP Opening seperate driver compartment with IP65 protection and impact resistance of IK07 fixed on wall with GI pipe of suitable dia and all fixing accessories including connecting up with & including twin core twisted flexible copper conductor cable of suitable size of 230V , 50 HZ etc complete all as specified and directed by Engineer-in-Charge .

M & L for Supply,laying ,connecting ,testing and commissioning and jointing , LT underground cable in replacement ,1100 volts grade, XLPE insulated, armored with galvanized round steel wire or steel strip, electric power cables heavy duty, with multi stranded aluminum conductor, laid in ducts, fixed on poles/walls with proper size saddles and clamp complete all as specified and as directed by the Engineer-in-Charge of following Sizes:-

(a) LT cable 16 Sqmm, 2 core.

Excavation in trenches n. exc 1.5 m wide and n. exc 1.5 m in depth and getting out in hard/dense soil etc complete all as specified and directed by Engineer-in-Charge

Returnig, filling in including spreading, levelling, watering and well ramming in layers, n exc 25 cm thick in soil etc complete all as specified and directed by Engineer-in-Charge

Removing exacavated soil to a distance n. exc 50 m and depositing where directed at a level n. exc 1.5 m above the starting point etc complete all as specified and directed by Engineer-in-Charge

Supply &lay HDPE pipe 50 mm bore for laying of LT cable complete with all accessores etc complete all as specified and directed by Engineer-in-Charge

Material & labour for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick burried directly in ground. Earth pit not less than 2.25 m depth and top edge of the earth plate not less than 1.5 m below normal ground level connected to galvanised earth lead wire 4.0 mm dia by means of nuts, bolts & washer etc. Earth wire connected upto main earth point / DBs alongwith 15mm dia earth protection pipe from top edge of the earth plate to main earth point to be connected and 20mm dia watering pipe light grade with funnel and provn of PCC using cement concrete (1:2:4) mix type B1 using granded stone aggregate and RCC pit cover 50 mm thick precost RCC (1:2:4) mix type B1 duly reinforced with 8 mm dia of TMT bar @ 100 mm CIC, both way, lifting arrangement complete including all necessary earth work etc complete all as specified and directed by Engineer-in-Charge

Supply and install hi wall split units indoor/outdoor of Capacity 1.5 Ton complete with cordless remote control unit and with in built air ioniser and Plasma filter for better indoor air quality with minimum 5 star rating and Efficient & Hyper Tropical Inverter Split AC with Copper , blue film condensor and it is Equipped with R410 A gas Refrigerant having 25 mtr long reach Air flow,6 speed fan control,noise level within 34 db , with warranty 01 year warrenty, equipped with Indoor/Outdoor, remote Etc. Make:- Hitachi/'O' general/Carrier

M&L for submain wiring with 2 runs of 4 Sqmm & one run of 4 Sqmm single core copper conductor cable 1100 Volts grade complete in & including PVC casing & caping complete.

Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 5.0 KVA complete all as specified and as directed.

S&F Sheet metal enclosure single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp complete all as specified and as directed.

Supply and fix electric water heater, storage type steel body and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, including Flexible pipe 2 set , PVC Connection pipe fastner fixed in wall Complete etc.

Supply and fix of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings 20 mm in trenches/walls complete all as specified with all fittings and joints etc complete all as specified and directed by Engineer-in-Charge

Supply and fix Bib taps, cast copper alloy with crutch or butterfly handle, screwed for iron pipe of for brass ferrule and fixed of size 15 mm bore etc complete all as specified and directed by Engineer-in-Charge

Supply and Fix 15 mm Stop valves, cast copper alloy,screwed down,high pressure,with crutch or butterfly handle,screwed both ends for iron pipe or for unions and fixed

Supply and lay in trenches/or on wall medium grade steel water tubing galvanised with all fittings and joints etc complete for size 15 mm bore

M&L for power point wiring complete on surface of wall (open) type with two runs of 2.5 sq mm for phase and neutral single core multistranded copper conductor of 1100 volts grade PVC insulated and unsheathed FRLSH cable drawn in and incl PVC Casing and capping ISI Marked with its accessories with provn of PVC boxes (Modualr upto 12 Module of Britz series of legrand) and fixed with brass screws cup washer for fixing switches/socket/regulators etc incl 2.5 sq mm single core multistranded copper conductor of 1100 volts grade PVC insulated and unsheathed FRLSH cable as Earth continuity conductor to common earth & connecting to earth dolly for the following, all as specified and directed. Note : 1. Proper colour coding shall be adopted for wiring (For Phase- Red, Yellow, Blue, For Earth - Green and For Neutral- Black) 2. All points are required to earthed upto fixtures i.e. Holders, Tube lights, Wall lights, bulkhead lights, bldg security light etc

S&F Modular Switch, 15/16 Amp, onw way, one Module as per existing. etc complete all as specified and directed by Engineer-in-Charge.

S&F Modular Socket Outlet 16 Amp - 3 pin two module as per existing etc complete all as specified and directed by Engineer-in-Charge.

Supply & fixing MCB , SP, AC, 240 Volts of 20 Amps capacity 16KA, 'C' series and making connections with suitable size of copper lugs etc complete all as specified and directed by Engineer-in-Charge

M/S. M. F. Sharif & Co.

M/s. N D Karande

M/s. R. R. ASSOCIATES

M/S. YADAV ENTERPRISES

M/s IBEX Engineers and Contractors

OM SAI ASSOCIATES