SPL REPAIR TO BLDG NO A/10/68 (TOILET BLOCK), A/10/69 (BATHROOM BLOCK), REPAIR/REPLACEMENT OF REFRIGERATORS, AC AND WATER COOLER AGAINST BER OF PH-1 IN THE AREA OF AGE BR-I UNDER GE PANAGARH (2ND CALL)

Amount

Dismantling old/rusted Asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings with ridges etc complete as specified and directed.

S&F 0.50 mm thick pre- painted galvalume aluminium zinc coating GI based corrugeted steel sheet of any colour as approved of 550 Mpa tensile strength as in roof covering / cladding to wall fixed with self tapping screws complete specified and directed.

M&L for pre-painted galvalume aluminium zinc coating GI based plain sheet 0.50 mm thick any colour having tensile strength of 550 Mpa as in ridges, hips valley gutter etc fixed with self tapping screws complete and as specified and directed.

Taking down chowkats or frames with shutter w/o taking off shutter from the frame n exc 1.5 Sqm each incl cutting holes for taking out hold fast or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.) all as specified and directed By Engr-in-charge.

Taking down chowkats or frames with shutter w/o taking off shutter from the frame exc 1.5 Sqm & n. exe 4 Sqm each incl cutting holes for taking out hold fast or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.) all as specified and directed By Engr-in-charge.

Demolition of brick work built in cement mortar or cement lime mortar incl all quoins, arches pillars etc and removing unserviceable material exc 100 mtr complete all as specified and directed.

M&L for brick work with fly ash ‘ B’ bricks straight or curved on plan exc 6 m mean radius build in CM (1:4) complete all as specified as directed.

M&L for brick work with fly ash ‘ B’ bricks as in half brick thick wall straight or curved on plan exc 6 m mean radius build in CM (1:6) complete all as specified as directed.

S&F solid PVC Door Frame of size 50mm x47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail;Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification.

S&F anodised powder coated aluminium frame for doors,windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified.

S&F anodised powder coated aluminium door shutters,aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, ruber neoprene packing,handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified.

Hacking Out Old Broken Glass (any thickness, size, quality or description) from Wooden Frames, Glazed with Putty or fixed with Beads, complete all as specified and as directed.

S&F 5.5 mm thick sheet glass, ordinary quality and glazing with oil putty in square n.exc 0.5 Sqm each panes complete all as specified and directed.

S&F plain, framed, panelled shutters 40 mm thick made of 1st class Hardwood (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store yard and rubbish off the premises complete all as specified and directed.

M&L for Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10 mm thick cement plaster in cement mortar (1:4) on brick or concrete surface all as specified as directed. (Note : Design, shade and pattern of fixing of tiles shall be as directed by Engr-in-charge)

Taking down cement plaster of any description on brick or stone walls or from concrete surface incl racking out joints hacking for key scrubbing with water etc complete all as specified and directed

M&L for rendering 20 mm thick in CM (1:4) on other than fair face of brick work surfaces finished even and smooth with out using extra cement complete all as specified and directed.

M&L for preparation of old wall surfaces complete removal existing finishes including filling of small holes etc and applying two coat of oil bound distemper over a coat of alkali resistant priming paint over one coat of putty minimum 3 mm thick complete all as specified as directed.

S&F PVC (SWR) Q trap 110/110 mm bore complete all as specified and directed

S&F vitreous china squatting pan log pattern 580 mm long including foot rest, S or P trap including lime concrete bedding complete all as specified and directed. (Make- M/s Parryware/ M/s Hindware/ M/s Cera)

S&F in repair Vitreous China valveless, syphonic action type,flushing cistern, low level, white, with inlet, ball valve,float and handle including brackets flushing cistern 10 ltrs capacity all completed as specified.

S&F in repair Flush pipe of chromium plated brass tube,32mm dia, for low level cisterns complete all as specified as directed.

S&F in repair Soap dish, vitreous China white, approximate size 160x 160x90mm complete all as specified as directed.

M&L for granite 20 mm thick(of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

S&F vitreous China urinals, bowl type (back to corner wall type), complete including providing and fixing plus, bedding urinal against wall in cement mortar 1:2 securing urinal to plus with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Note : Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe).

S&F urinal spreader of PTMT any colour for fixing with 15 mm dia pipe complete all as specified and directed. (Minimum weight 60gms)

S&F in repair vitreous counter sunk wash basin white,flat back of size 580x 450mm including 32mm dia PVC waste pipe CP brass wast coupling 32 mm dia , pair of MS angle brackets or MS fastener/ bolts for fixing arrangements 450mm long pvc connection with PVC nut and washer complete at site and all as directed by Engr-in- charge.

S&F in repair pillar tap 15 mm dia cast copper alloy fancy type with capstan heads chromium pleted screwed down high pressure with or without lettered Hot or Cold with long screwed screwed shanks and fly nuts screwed for iron pipe fixed complete all as specified and directed.

S&F PVC connection 15 mm x 450 mm including brass check nut at both ends screwed for iron pipe of 15 mm bore complete all as specified and directed.

S&F in repair Bib tap long body with CP nipple cast copper alloy with crutch or butterfly handle, chromium plated fency type screwed for iron pipe, suitable for 15 mm bore complete all as specified and directed

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long with aluminium alloy brackets and guard rail all completed as specified and directed.

S&F in repair tubular towel rail /towel ring 20mm dia D type and 60cm long between flanges of brass chromium complete all as specified and directed

S&F in repair brass chromium plated shower rose 125 mm size swivel type with connecting rod 15 mm bore complete all as specified and directed.

S&F in repair stop valve cast copper chromium plated concealed with long shank type screwed down, high pressure with capstan head suitable for 15 mm bore complete all as specified.

S&F in repair Grating square 150 mm size of PTMT (Minimum weight 100gms) complete all as specified and directed

Takind down GI tubing of 15 mm dia and connection and incl cleaning for refixing or removel complete all as specified and directed

S&F 15 mm dia galvanized pipes medium grade with all fittings and fixed complete wall and ceiling or laid in floors complete all as specified and directed.

Cutting chases for concealed water tubing or concealed conduit & making good in CM 1.3 of girth exe 10 cm and n.exe 20 cm in brick wall complete all as specified and directed.

M&L for providing pre-cast cement concrete 1:2:4 type B-1(20 mm grd agg) for cover slab, manholes etc set in CM (1:4) complete all as specified and directed

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams, and similar work, vertical or to batter complete all as specified and directed.

M&L for reinforced cement concrete (nominal mix) type B-1 1:2:4 (20mm graded stone aggregate) foundations, including rafts, footings, foundation beams, plinth beams; bases for columns, etc. and mass concrete etc complete all as directed.

Dismantling cast iron work of any description CI pipes incl all fittings like bend, branch pieces, connectors, heel rest bend etc all as specified and directed.

S&F PVC SWR pipes 110 mm bore single socketed in any length with rubber ring joint fixed to wall or laid in trenches or in floors with steel clamps all as specified and directed . (Make : M/s Supreme/ M/s Finolex).

S&F PVC SWR pipes 75 mm bore single socketed in any length with rubber ring joint fixed to wall or laid in trenches or in floors with steel clamps all as specified and directed.

S&F PVC (SWR) floor trap plain including jointing with solvent cement 75 mm dia complete all as specified and directed.

S&F PVC (SWR) vent cowl 75 mm bore complete all as specified and directed.

S&F PVC (SWR) WC connector with lip ring 110 mm complete all as specified and directed.

S&F PVC (SWR) gully trap 125/110 mm setting and jointing with solvent cement complete all as specified and directed

S&F aluminium anodised barrel tower bolts 200 mm long, of extuded section and fixed stove enamelled black with bright bolt complete all as specified and directed.

S& F aluminium alloy anodied sliding door bolt size 250mm with hasp staplw (bolt type ) and fifing clips of sheet cast or extruded section and fixing bolt and sliding bolts of extrueded section or cast aluminium alloy and fixed complete all as specified and directed

S&F 125 mm aluminium handle cast type anodized complete all as specified and directed

S&F 100 mm long hasp and staple, aluminium anodized with bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F stainless steel butt hinges of size 100 mm for PVC door complete all as specified and directed

S&F tower bolt of size 150 mm for PVC door complete all as specified and directed

S&F Bow handle of size 150 mm for PVC door complete all as specified and directed

Demolition and breaking up drain pipes of internal dia 150mm (SGSW/PVC/RCC etc) set in cement mortar including bed concrete and removal of debris to low lying area of distance not exceeeding 100m complete all as directed by Engr-inCharge.

M&L for Concrete bed to 150 mm dia drain pipes including packing under and haunching against the sides of pipes after they are laid and tested in PCC 1:3:6 type C2 (using 40mm graded stone aggregate) all as specified and directed.

Supplying and laying UPVC Eco drain Hi-tech pipe drainage sewer system pipe bearing 160 mm dia minimum 4mm thick incluing jointing with coupler, bend tee as per site requirement complete laid in trenches or floors complete all as specified and directed. (Note:-Necessary PCC haunching/benching/ packing shall be measured and paid separately).

Excavating over areas, n exc 1.5 m deep and getting out soft/loose soil complete all as specified and directed.

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick spread, levelled and rammed including watering complete all as specified and directed.

M&L for Cement concrete (1:4:8) Type D2 using 40 mm graded aggregates as in foundations, filling and mass-concrete complete all as specified and directed.

M&L for PCC (1:2:4) Type B2 using 40 mm graded aggregate used as in sub base floor/pavings and finishing cement concrete surface without using extra cement complete all as specified and directed.

M&L for Sand filling under floors or in foundation including watering and consolidation complete all as specified and directed.

M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade with grey cement and pigments complete all as specified and directed.

M&L for rendering 15 mm thick in CM (1:4) on fair faces of brick work or concrete surfaces of wall, surface finished even and smooth without using extra cement complete all as specified and directed. (Note: WPC will be measured seperately)

M&L for PCC (1:2:4) Type B0 using 12.50 mm graded aggregate used as in copings complete all as specified and directed.

Supply, Laying and Testing of Reinforced concrete pipes class NP2 , laid and jointed complete with collars 150mm bore complete all as specified and as directed.

M&L for PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in bed to drain pipes including forming cradels for 150 mm bore pipes complete all as specified and as directed

Removing excavated spoil to a distance not exc.50m and depositing where directed at a level not exc. 1.5 m above the starting point complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in hard/dense soil complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and getting out complete all as specified and directed

M&L for Cement concrete (1:3:6) Type C2 using 40 mm graded aggregates as in foundations, filling and mass-concrete complete all as specified and directed.

M&L for precast RCC (1:2:4) type B1 using 20 mm graded aggregates as in Cover Slabs set in CM (1:6) complete all as specified and directed.

M&L for mild steel bars 6 to 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

S&F Low density polyethylene pipes (LDPE) of 50 mm bore of pressure rating 6 kgf/cm2 laid in trenches as in weep holes complete all as specified and directed

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, mounds, mitred/stopped end etc complete all as specified and directed.

Add or deduct for each 25 mm girth or part thereof over or under 30 cm ditto complete all as specified and directed

Taking down cement plaster of any description on concrete surfaces such as soffit of chajjas and brick walls etc incl raking out joints, hecking for key scrubbing down with water and removal of rubbish off the premises complete all as specified and directed.

M&L for rendering 10 mm thick cement plaster in cement mortar (1:6) on brick work or concrete surfaces including finished even and smoothh without usig extra cement complete all as specified and directed.

Supply only Liquid water proofing compound complete all as specified and directed.

M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. (Make: M/s Apex Ultima of Asian/ Weather Coat all guard of Berger/Xtra Tough of Shalimar).

M&L for preparation of new surfaces of wall and applying three coats of white wash complete all as specified and directed.

M&L for Non - skid Ceramic Coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry over screed bed or bedding layer of 15 mm thick with cement mortar 1:6 and pointed in white or coloured cement to match complete all as specified and directed.

S&F for Mild Steel wind ties for roof including securing bolts complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed

S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and directed.

Demolition of cement concrete (un-reinforced) not exceeding 15 cm thickness (above or below ground level) complete all as specified and directed.

Surface dressing n exc 15 cm deep in soft /loose soil complete all as specified and directed.

M&L Hardcore of gauge n exc. 63mm, deposited, spread and leveliled in layers n exc. 150mm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 100mm thick Cement concrete type B- 2,1:2:4 (using 40mm graded stone aggregate) as in subbase of floor complete all as specified and directed.

M&L 25mm thick Cement concrete type B-0, 1:2:4 (12.5mm graded aggregate) as in floor for levelling course complete all as specified and directed by Egineer-in-Charge.

Supply and fix Steel windows with side hung shutters (minimum wt. of steel section should be 1.42 kg/M) including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded, complete all as specified and directed.

Supply and Fix Steel ventilators with centre hung shutter (minimum wt. of steel section should be 1.42 kg/M) including two pairs of brasscup pivots, catch spring and pulleywheel, complete dovetailed or welded including pintol hinges, steel handles, etc. as shown with fixed type complete all as specified and directed.

M&L for two coats synthtic enamel paint over a coat of red oxide primer on new steel surfaces incl preparation of surfaces over 10 cm width or girth complete all as specified and directed.

M&L for two coats synthtic enamel paint over a coat of red oxide primer on old steel surfaces incl preparation of surfaces over 10 cm width or girth complete all as specified and directed.

M&L for framed work such as grills etc with endsof bars shouldered nd or riveed or forged into spike, framed guard bars and similar work conforming to Fe 290 Gde-E-165 complete all as specified and directed.

M&L for 3mm thick plain sheet glass ordinary quality & glazing with oil putty n.exc 0.50 Sqm in each pane complete all as spd and directed by Engr-In-Charge .

M&L for 3mm thick plain sheet glass ordinary quality, glass is ground or obscured or frosted, on one side & glazing with oil putty n.exc 0.50 Sqm in each pane complete all as spd and directed by Engr-In-Charge.

Supply and fix stainless steel butt hinges 100MM, medium weight complete all as specified and directed.

Supply and fix 150 mm long aluminium anodised barrel tower bolt of extruded section and fixed complete all as specified and directed.

Supply and fix 150 mm aluminium handle cast type, anodised, complete all as specified and directed

S&F 300 mm Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed

Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc, but excluding ashlar facings, dressedstonework and precastconcrete articles complete all as specified and directed

M&L for brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified and as directed.

M&L for brick work with flyash bricks straight or corve on plan to any radius in half bricks thick walls, built in cement mortar (1:4) complete all as specified and directed.

M&L for 75mm thick Cement concrete type C-2, 1:3:6 (40mm graded stone aggregate) as in plinth protection and paving complete all as specified and directed

S&F in repairs closet Vitreous china squatting pan Orissa pattern of size 580x440mm white with integral foot rests (excluding flusing cistern and flush pipe) including connection to trap and to flushing pipe, antisyphonage connection pipe etc complete making good disturb surface with existing finish of floor all as specified & directed by Engineer-in-Charge.

S&F 110mm PVC (SWR) 'P’ trap complete all as specified and directed.

S&F in repair 110 mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors and jointed complete all as specified and as directed by EIC.

All as per item No 112.00 mentioned here-in-above but 75 mm bore complete all as speified and directed

S&F in repair 110mm bore PVC (SWR) bends with access door any radius complete all as specified and as directed by EIC.

S&F in repair 110 mm bore PVC (SWR), junction single, (single T), equal or unequal with access door complete all as specified and directed.

S&F, 75mm bore PVC (SWR) bends with rubber ring joints with access door and jointed complete all as specified and as directed by EIC.

S&F in repair Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white minimum), with grating and union for discharge pipe(back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe.

S&F flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern etc complete all as specified and directed

S&F in repair 32 mm bore Waste coupling of PTMT (half or full threaded) suitable urinal . (Minimum weight 32mm45gms/40mm-60 gms

S&F in repair PVC connection 15 mm size PTMT nuts of length ength 600 mm complete all as specified and directed

S&F CP tubular towel rail 20mm dia D type 60cm between two flange including bracket complete all as specified and directed by Engineer -in-Charge

Supply and fix in repair bib taps of 15mm bore fancy type, chromium plated cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for brass ferrule complete all as specified and directed.

Supply and fix in repair stop valve of 15mm bore , chromium plated with long shank and cup concealed type cast copper alloy, screwed down, high pressure, with crutch handle, screwed both ends for brass ferrule complete all as specified and directed.

S&F in repair 125mm Brass Chromium Plated shower rose with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed

S&F in repair soap dish vitreous china white size 160x160x90mm approx complete all as specified and directed by Engineer -in-Charge

S&F in repair 75 mm outer dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed

S&F in repair 75mm outer dia PVC (SWR) multi floor trap with grating including jointing with solvent cement complete all as specified and directed

S&F in repair PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed

S&F in repair grating square 150mm size of PTMT (minimum weight 100 gms) complete all as specified and directed

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed

S&F Shelf of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 300gms) complete all as specified and directed

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed

M&L for PCC type D-2, 1:4:8 (using 40mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and directed.

M&L for Reinforced cement concrete (nominal mix) type B1(1:2:4) using 20mm graded aggregate Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Taking up or down 20 mm dia bore steel tubing and connection including cleaning for refixing or remove to store complete all as specified and directed.

S& F GI 20 mm dia bore steel tubing medium grade galvanised with all fittings & connection complete all as specified and directed.

M&L for sand filling under floors or in foundation including watering and consolidation complete all as specified and directed.

Removing surplus soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in hard/dense soil complete all as specified and directed.

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams, and similar work, vertical or to batter complete all as specified and directed.

M&L for formwork for rough finished surface of concrete (flat surface) to sides of pillars, posts, struts, piers, columns, and stanchions complete all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. for fair finished surfaces of concrete complete all as specified and directed.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work for rough finished surface, not exceeding 200m thick (Horizontal or sloping) complete all as specified and directed.

M&L for reinforced cement concrete (Design Mix) M-25 (20mm graded stone aggregate) foundations, including rafts, footings, foundation beams, plinth beams; bases for columns, etc. and mass concrete etc complete all as directed.

M&L for reinforced cement concrete (Design Mix) M-25 (20mm graded stone aggregate) in columns, pillars, piers, etc complete all as specified and directed.

M&L for reinforced cement concrete (Design Mix) M-25 (20mm graded stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for reinforced cement concrete (Design Mix) M-25 (20mm graded stone aggregate) in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

All as per item No 148.00 mentioned here-in-above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed.

M&L for rendering 15 mm thick in CM 1:4 on fair faces of brick work or concrete wall surfaceS&Finishing the surfaces fair and even complete all as specified and directed.

Supply only Integral Water proofing compound complete all as specified and directed.

M&L for rendering 15 mm thick cement plaster in CM 1:6 on external fair faces of brick/concrete work surfaces finished even and smooth (without using extra cement) incl WPC complete all as specified and directed (Note: WPC will be measured and paid separately).

M&L for rendering 5 mm thick in CM 1:3 on fair faces of brick work or concrete wall surfaceS&Finishing the surfaces fair and even on ceiling complete all as specified and directed.

M&L for finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) including preparation of newly plastered surface of concrete complete all as specified and directed.

M&L for preparation new plastered surfaces and applying three coat of white washing on ceiling complete all as specified and directed

M&L for broken bricks hard core gauge n.exc 63mm deposited, spred and levelled in layers n.exc 15cm thick, watered and rammed to a true surfaces complete all as specified and directed.

M&L for 75 mm thick PCC type C-2, 1:3:6 (using 40 mm graded stone aggregate) finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for cement concrete type B-0, 1:2:4 (using 12.5 mm graded stone aggregate) 25 mm thick as in floor for receiving screed bed complete all as specified and directed.

S&F Bib tap long body with CP nipple cast copper alloy with crutch or butterfly handle, chromium plated fancy type screwed for iron pipe, suitable for 15 mm bore complete all as specified.

S&F pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long with aluminium alloy brackets and guard rail all completed as specified.

S&F in tubular towel rail /towel ring 20mm dia D type and 60cm long between flanges of brass chromium plated complete all as specified and directed.

S&F in stop valve cast copper chromium plated concealed with long shank type screwed down, high pressure with capstan head suitable for 15 mm bore complete all as specified.

S&F in Grating square 150 mm size of PTMT (Minimum weight 100gms) complete all as specified and directed

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be convered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvant cement for stiles and plain colour PVC sheet top rail, lock rail and bottom rail on either side and as gap insert of top rail and bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitabale PVC sheet beading, and jointed together with solvant cement, and S&F in the frame at side as per specification and drawing complete all as specified and directed.

M&L for PCC (1:2:4) type B-0 as in bed blocks for hold fast including necesssary formwork complete as directed.

S&F mild steel flat iron of size 25 X 6 mm work as in hold fast and similar small articles including required cutting , bending and fixing complete, mild steel conforming to Fe-290 Gde-E-165 ,complete all as specified and directed.

S&F 100 mm size butt hinges extruded aluminium alloy with galvanized mild steel hing pin anodised and fixed type C-21 complete all as specified and directed

S&F 200 mm long Aluminium, anodised, barrel tower bolt of extruded section complete all as specified and directed.

S&F aluminium handles, cast type, anodised 150mm long complete all as specified and directed.

S&F 300 mm long Aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy and fixed complete all as specified and directed.

S&F Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and directed.

S&F vitreous china wash basin white, flat back, size 550X400 mm including cutting for pinning in ends of brackets, complete all as specified and directed.

S&F pipe of polyethylene of low or high density of PVC, 32 mm dia, for low level cistern complete all as specified and directed.

S&F PVC connection 15 mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F soap dish, vitreous china white, approximate size 160 x 160 x 90mm complete all as specified and directed.

S&F PVC (SWR) floor trap 75mm dia of outlet plain with grating including jointing with solvent cement complete all as specified and directed

S&F PVC (SWR) bends any radius of 75 mm bore with access door complete all as specified and directed.

M&L for laying Reinforced concrete pipes 150 mm in dia, class NP2, laid and jointed complete with collars complete all as specified and directed.

M&L for Concrete bed to 150 mm dia drain pipes including packing under and haunching against the sides of pipes after they are laid and tested in PCC 1:3:6 type C2 using 40mm graded stone aggregate all as specified and directed.

On site Hume Pipe Septic Tank designed to carry sewage and sullage water, excavation in any type of Soil, PCC 1:4:8 below foundation, vent shaft, connectionetc., complete for 20 users complete all as specified and directed.

Soakage wells excavation, in any type of soil, foundation in PCC 1:3:6 walls of honey combed masonry with top ring of M-25 Concrete including intercepting chamber and screen chamber made of Brick masonry in CM, RCC cover slab in M 25/SFRC cover, interconnecting ppes of RCC/ DWC complete filled with brick bats of size 1.2 m by 1.5 m effective depth complete all as specified and directed.

Excavation in trenches not exc 1.5m wide and not exc 1.5m deep for foundation etc or for shafts n.exc 10 Sqm on plan and n.exc 1.5m in depth and getting out in hard/dense soil complete all as specified and directed

M&L for sand filling under floors or in foundation including watering and consolidation complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 (using 40mm graded stone aggregates) as in bed concrete for foundation filling & mass concrete complete all as specified and directed.

M&L for formwork for rough finished surface of concrete (flat surface) to sides of pillars, posts, struts, piers, columns, and stanchions complete all as specified and directed.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work for rough finished surface, not exceeding 200m thick (Horizontal or sloping) complete all as specified and directed.

M&L for reinforced cement concrete (nominal mix) type B-1 1:2:4 (20mm graded stone aggregate) in columns, pillars, piers, etc complete all as specified and directed.

M&L for reinforced cement concrete (nominal mix) type B-1 1:2:4 (20mm graded stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for reinforced cement concrete (nominal mix) type B-1 1:2:4 (20mm graded stone aggregate) in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L for damp proof course 40mm thk in cement concrete 1:2:4 type B-0 to horizontal or vertical surfaces including necessary form work complete all as specified and directed.

M&L for rendering 15 mm thick in CM 1:6 on fair faces of brick work or concrete wall surfaceS&Finishing the surfaces fair and even complete all as specified and directed.

M&L rendering 20 mm thick cement plaster in CM 1:6 on external fair faces of brick/concrete work surfaces finished even and smooth (without using extra cement) incl WPC complete all as specified and directed. (Note: WPC will be measured and paid separately).

M&L for rendering 5 mm thick in CM 1:6 on fair faces of brick work or concrete wall surfaceS&Finishing the surfaces fair and even on ceiling complete all as specified and directed.

M&L for finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and directed

M&L for preparation new plastered surfaces and applying three coat of white washing on ceiling complete all as specified and directed.

M&L for broken bricks hard core gauge n.exc 63mm deposited, spred and levelled in layers n.exc 15cm thick, watered and rammed to a true surfaces complete all as specified and directed.

M&L for 100 mm thick PCC type C-2, 1:3:6 (using 40 mm graded stone aggregate) finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L cement concrete type B-0, 1:2:4 (using 12.5 mm graded stone aggregate) 25 mm thick as in floor for receiving screed bed complete all as specified and directed

M&L for coloured non skid ceramic tiles 7 to 8 mm thick (square /rectangular) area of each tile exceeding 0.06sqm but not exceeding 0.11 sqm, in floors etc set and jointed in neat cement slurry over 15 mm thick screed bed or bedding layer in cement mortar (1:4) complete all as specified and directed.

Takind down GI tubing of 15 mm dia and connection and incl cleaning for refixing or removel complete all as specified and directed.

S&F 200 mm long Aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy and fixed.

S&F for 15 mm dia medium grade galvanised steel water tubing,with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

S&F Vitreous China squatting pan of pattern “long pan”, size 580 mm white with ‘P’ or ‘S” trap, front or back inlet and foot rests, any pattern (excluding flushing cistern and flush pipe) complete all as specified and directed.

Supply only 10 ltrs PVC valveless, syphonic action type, flushing cistern, low level, white, with intel, ball valve, float and handle including brackets complete all as specified and directed. (Note: Fixing rate included in Ser item No 42 above of WC item)

S&F in 15 mm bore stop valve cast copper alloy screwed down, high pressure, with crutch or but-ter fly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F 15mm dia bib tap cast copper alloy chromium plated with crutch (or) butterfly handles, screwed down screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F 15 mm pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed

Supply flush pipe of polyethylene of low or high density of PVC, 32 mm dia, for low level cistern complete all as specified and directed.

S&F PVC connection 15 mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F 20mm bore for gun metal glove or gate valves with iron wheel head screwed both ends for iron pipe complete all as specified and directed

S&F soap dish, vitreous china white, approximate size 160 x 160 x 90mm complete all as specified and directed.

S&F PVC (SWR) bends any radius of 75 mm bore with access door complete all as specified and directed.

S& F Vitreus China bowl urinal flat back Size of 465 x 355 x 265 mm white with grating and union for discharge pipe complete all as specified and directed.

S&F Urinal Spreader of PTMT any colour for fixing with 15 mm dia pipe complete all as specified and directed

M&L for Salt -glazed stoneware drain pipes of 150 mm internal dia laid in trenches and jointed complete all as specified and directed

M&L for concrete bed to 150 mm dia drain pipes including packing under, haunching against the sides of pipes after they are laid and tested in cement concrete 1:3:6 type C-2 complete all as specified and directed.

On site Hume Pipe Septic Tank designed to carry sewage and sullage water, excavation in any type of Soil, PCC 1:4:8 below foundation, vent shaft, connection etc., complete for 20 users complete all as specified and directed.

Soakage wells excavation, in any type of soil, foundation in PCC 1:3:6 walls of honey combed masonry with top ring of M-25 Concrete including intercepting chamber and screen chamber made of Brick masonry in CM, RCC cover slab in M 25/SFRC cover, interconnecting ppes of RCC/ DWC complete filled with brick bats of size 1.2 m by 1.5 m effective depth complete all as specified and directed.

Excavation in trenches not exc 1.5m wide and not exc 1.5m deep for foundation etc or for shafts n.exc 10 Sqm on plan and n.exc 1.5m in depth and getting out in soft/loose soil complete all as specified and directed.

M&L for sand filling under floors or in foundation including watering and consolidation complete all as specified and directed.

Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed with 1st class Hardwood complete all as specified and directed.

Flush shutters 40 mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be convered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvant cement for stiles and plain colour PVC sheet top rail, lock rail and bottom rail on either side and as gap insert of top rail and bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitabale PVC sheet beading, and jointed together with solvant cement, and S&F in the frame at side as per specification and drawing complete all as specified and directed.

Anodised powder coated aluminium frame for doors,windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified.

Sheet glass 5.5 mm thick , ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed.

M&L for PCC (1:2:4) type B-0 as in bed blocks for hold fast including necesssary formwork complete as directed.

S&F mild steel flat iron as in hold fast, clamps articles conforming to FE 290 Gde-E-165 complete all as specified and directed.

S&F 100 mm size butt hinges extruded aluminium alloy with galavanised mild steel hing pin anodised and fixed type C-21 complete all as specified and directed

S&F 200 mm long Aluminium, anodised, barrel tower bolt of extruded section complete all as specified and directed.

S&F aluminium handles, cast type, anodised 150mm long complete all as specified and directed.

S&F 300 mm long Aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy and fixed complete all as specified and directed.

Supply only 10 ltrs PVC valveless, syphonic action type, flushing cistern, low level, white, with intel, ball valve, float and handle including brackets (Note: Fixing rate included in Ser item No 42 above of WC item)

S&F vitreous china wash basin white, flat back, size 550X400 mm including cutting for pinning in ends of brackets, complete all as specified and directed

Supply flush pipe of polyethylene of low or high density of PVC, 32 mm dia, for low level cistern complete all as specified and directed.

S&F soap dish, vitreous china white, approximate size 160 x 160 x 90mm complete all as specified and directed.

S&F PVC (SWR) bends any radius of 75 mm bore with access door complete all as specified and directed.

S& F Vitreus China bowl urinal flat back Size of 465 x 355 x 265 mm white with grating and union for discharge pipe complete all as specified and directed.

S&F Urinal Spreader of PTMT any colour for fixing with 15 mm dia pipe complete all as specified and directed

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required for Internal dia 150 mm of pipe complete all as specified and directed.

M&L for laying Reinforced concrete pipes 150 mm in dia, class NP2, laid and jointed complete with collars complete all as specified and directed.

M&L for Concrete bed to 150 mm dia drain pipes including packing under and haunching against the sides of pipes after they are laid and tested in PCC 1:3:6 type C2 using 40mm graded stone aggregate complete all as specified and directed.

Supply & fix in repair for 25mm bore GI tubing medium grade in trenches / Floor / pillar connetion in old or new postion including fittings all as specified & as directed including taking down old unseviceable pipe complete all as specified and directed. (Make: M/s Bansal / M/s Jindal)

All as per item No 244.00 mentioned here-in-above but 40 mm bore complete all as specified and directed

S&F in repairs, 25 mm bore dia pipe gun metal globe or gate valves, yoke type, full opening with iron wheel head, screwed both ends heavy duty, ISI marked complete for iron pipes complete all as specified and directed.

Rotational / moulded Polyehtylene water tank (Cylindrical vertical with closed top) hoisted & fixed in position all as specified directed .capacity of 1000 Ltr including dismantalling old unserviceable complete all as specified and directed.

S&F in repair Ball brass valves, high pressure, with polyethylene float and flynut complete, screwed for iron pipe or brass ferrule for 25mm bore complete including taking down complete all as specified and as directed.

Supply & fix in repair for 25mm bore GI tubing medium grade in trenches / Floor / pillar connetion in old or new postion including fittings all as specified & as directed including taking down old unseviceable pipe complete all as specified and directed. (Make: M/s Bansal / M/s Jindal)

All as per item No 249.00 mentioned here-in-above but 40 mm bore complete all as specified and directed.

S&F in repairs, 25 mm bore dia pipe gun metal globe or gate valves, yoke type, full opening with iron wheel head, screwed both ends heavy duty, ISI marked complete for iron pipes complete all as specified and directed.

Rotational / moulded Polyehtylene water tank (Cylindrical vertical with closed top) hoisted & fixed in position all as specified directed .capacity of 500 Ltr including dismantalling old unserviceable complete all as specified and directed.

S&F in repair Ball brass valves, high pressure, with polyethylene float and flynut complete, screwed for iron pipe or brass ferrule for 25mm bore complete including taking down all as specified and as directed.

Supply & fix for 25mm bore GI tubing medium grade in trenches / Floor / pillar connetion in old or new postion including fittings complete all as specified and as directed. (Make: M/s Bansal / M/s Jindal)

All as per item No 254.00 mentioned here-in-above but 40 mm bore complete all as specified and directed.

S&F 25 mm bore dia pipe gun metal globe or gate valves, yoke type, full opening with iron wheel head, screwed both ends heavy duty, ISI marked complete for iron pipes complete all as specified and directed.

S&F capacity of 500 ltr Rotational / moulded Polyehtylene water tank (Cylindrical vertical with closed top) hoisted & fixed in position all as specified directed.

S&F Ball brass valves, high pressure, with polyethylene float and flynut complete, screwed for iron pipe or brass ferrule for 25mm bore complete including taking down all as specified and as directed.

Supply & fix in repair for 25mm bore GI tubing medium grade in trenches / Floor / pillar connetion in old or new postion including fittings complete all as specified and directed. (Make: M/s Bansal / M/s Jindal)

All as per item No 259.00 mentioned here-in-above but 40 mm bore complete all as specified and directed

S&F in repairs, 25 mm bore dia pipe gun metal globe or gate valves, yoke type, full opening with iron wheel head, screwed both ends heavy duty, ISI marked complete for iron pipes complete all as specified and directed.

Rotational/moulded Polyehtylene water tank (Cylindrical vertical with closed top) hoisted & fixed in position all as specified directed .capacity of 1000 Ltr complete all as specified and directed.

S&F in repair Ball brass valves, high pressure, with polyethylene float and flynut complete, screwed for iron pipe or brass ferrule for 25mm bore complete including taking down all as specified and as directed.

Supply & fix in repair for 25mm bore GI tubing medium grade in trenches / Floor / pillar connetion in old or new postion including fittings all as specified and directed. (Make: M/s Bansal / M/s Jindal)

All as per item no 264.00 mentioned here-in-above but 40 mm bore complete all as specified and directed

S&F in repairs, 25 mm bore dia pipe gun metal globe or gate valves, yoke type, full opening with iron wheel head, screwed both ends heavy duty, ISI marked complete for iron pipes complete all as specified and directed.

Rotational / moulded Polyehtylene water tank (Cylindrical vertical with closed top) hoisted & fixed in position all as specified directed .capacity of 500 Ltr complete all as specified and directed.

S&F in repair Ball brass valves, high pressure, with polyethylene float and flynut complete, screwed for iron pipe or brass ferrule for 25mm bore complete including taking down all as specified and as directed.

E/M PORTION M&L for point wiring for light point/ fan point, one light/fan/exhaust fan point controlled by one, one way switch using 1.5 sqmm nominal cross sectional area multistranded copper conductor ,PVC insulated unsheathed FRLS cables in and including 20 mm dia or higher size PVC concealed conduits and fittings of medium grade, including pressed steel terminal switch boxes, 3 mm thick bakelite sheet top cover (ISI Marked) fitted with chromium plated brass screws & washers and 1.5 sqmm nominal cross sectioanl area multistranded copper conductor FRLS PVC insulated unsheathed earth wire and connecting to earth dolly and brass screws, washers etc complete all as specified and directed.

M&L for wiring for socket outlet 3 pin, 15 amps on independent Boards controlled by one, one way switch using 4.0 sqmm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLS cables in and including 20 mm dia or higher size PVC concealed conduits and fittings, including pressed steel terminal switch boxes , 3 mm thick bakelite sheet top cover (ISI Marked) fitted with Chromium plated brass screws & washers and 4.0 sqmm nominal cross sectioanl area multistranded copper conductor , PVC insulated unsheathed FRLS cable earth wire and connecting to earth dolly and brass screws, washers etc. complete all as specified and directed.

M&L for wiring for socket outlet 3 pin, 5 amps on independent Boards controlled by one, one way switch using 2.5 sqmm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLS cables in and including 20 mm dia or higher size PVC concealed conduits and fittings, including pressed steel terminal switch boxes , 3 mm thick bakelite sheet top cover (ISI Marked) fitted with Chromium plated brass screws & washers and 2.5 sqmm nominal cross sectioanl area multistranded copper conductor , PVC insulated unsheathed FRLS cable earth wire and connecting to earth dolly and brass screws, washers etc. complete all as specified and directed.

S&F switch socket combination 2 in 1 multipurpose 5 pin , (6 Amps ) complete all as specified.

S&F switch piano flush type, single pole , 6 Amps, one way complete all as specified.

S&F switch socket combination 16 Amps flush type controlled by one switch complete all as specified.

S&F ceiling rose surface bakelite 65 mm x 50 mm two to three terminal suitable for 230 Volts AC 6 Amps complete all as specified.

S&F exhaust ventilation fan with louvers of sweep 300mm, metalic body, 240 volts, BEE 5 star rated, ISI marked complete all as directed by Engr-in-Charge.

S&F 20 W LED batten light fittings with extruded polycarbonate complete with all accessories and connection from ceiling rose with twin core twisted flexible copper conductor cable with suitable size and earthing complete, complete all as directed.

S&F 9 W LED light fitting wall mounted batten 2ft , extruded polycarbonate, enivromental friendly, heat sink provided for efficent heat dissipation and integrated electronic driver for 9 watt , 6000K including necessary connection complete all as specified and directed.

S&F security light fittings 25 watts, minimumm lumen output 100 lumen/Watt, made up of pressure dia cast housing with prismatic polycarbornate diffuser and individual LED with secondary optic and IP65 including necessary connection complete suitable for pole dia 25mm complete with all accessories including connected with twin core twisted flexible copper conductor of suitable size complete all as directed. (Make - Bajaj/Crompton/Phillips/Havells)

S&F epoxy powder coated sheet metal enclosure for DBs, double door (when MCBs to be used), Single pole and neutral 240 V, 8 ways with mounting fitted with bus bar, DIN channel , neutral link and incoming contact complete all as directed.

S&F MCB SP, 6 to 32 Amps, 'C' series 10kA, 240 Voltsand to be housed in DBs including necessry connection complete all as specified and directed. (Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating).

S&F MCB SPN 32 Amps, 'C' series 10kA, 240 Volts and to be housed in DBs complete including necessry connection all as specified and directed. (Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating).

S&F two single core ,6 sqmm nominal cross sectional area multistranded copper conductor FRLS cable, PVC insulated unsheathed 1100 Volts grade drawing in and including nd including suitable size PVC conduit (ISI marked), concealed, including 6 sqmm nominal cross sectional area multistranded copper conductor FRLS cable, PVC insulated unsheathed 1100 Volts grade earth wire complete all as specified and directed.

S&F XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 16 Sqmm 2 core complete all as specified.

Excavation in trenches not exceeding 1.5m wide and not exc. 1.5m depth and getting out in hard/dense soil complete all as specified and as directed.

Returning, filling, including spreading, leveling, watering and well ramming in layers not exc. 25cmin soft/loose soil complete all as specified and as directed.

Removal of excavated soil to a distance not exc 50 m and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as directed.

Supply and lay for dry river sand filling for cable protection with a layer of 8cm deep before laying and 15cm covering above the top edge of cable after laying complete all as specified and as directed. (Note : Punned thickness shall be measured).

M&L for sub class B bricks locally available of size 25 x 12.5 x 7.5 cm laid dry width wise across the line of cable in trenches for protection of UG cable complete all as specified and directed.

M&L for earthing complete with galvanised mild steel earth plate electrode 600x600x6.0mm thick, burried directly in ground to a depth not less than 2.25 metres deep below ground level with top edge of earth plate not less than 1.5 metre below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate, using GI wire 4 mm dia as earth strip electrode bolted or rivetted to earth plate at one end and connected to equipments at another end, GI earth strip encased in and including 40 mm dia GI 'light grade' pipe from upper end of earth plate upto equipments,20 dia bore GI pipe 'light grade' as water pipe from earth chamber to upper edge of earth plate, Test point , GI funnel with wire mesh fixed on water pipe and PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in pit chamber and RCC pit cover 50mm thick precast RCC 1:2:4 type B-1, duly reinforced with MS round bars 6mm dia @ 100 c/c both ways with 10mm dia MS round bar as in lifting handles, excavation, earth work including laying the GI pipe concealed in floor/wall all as described in electric plate of SSR Part I complete all as specified and directed and testing on completion. (Note :- If the desired earth resistance is not found, earthing shall be redone by the contractor at no extra cost to the department).

M&L for point wiring for light point/ fan point, one light/fan/exhaust fan point controlled by one, one way switch using 1.5 sqmm nominal cross sectional area multistranded copper conductor ,PVC insulated unsheathed FRLS cables in and including 20 mm dia or higher size PVC concealed conduits and fittings of medium grade, including pressed steel terminal switch boxes, 3 mm thick bakelite sheet top cover (ISI Marked) fitted with chromium plated brass screws & washers and 1.5 sqmm nominal cross sectioanl area multistranded copper conductor FRLS PVC insulated unsheathed earth wire and connecting to earth dolly and brass screws, washers etc. complete all as specified and directed.

M&L for wiring for socket outlet 3 pin, 15 amps on independent Boards controlled by one, one way switch using 4.0 sqmm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLS cables in and including 20 mm dia or higher size PVC concealed conduits and fittings, including pressed steel terminal switch boxes , 3 mm thick bakelite sheet top cover (ISI Marked) fitted with Chromium plated brass screws & washers and 4.0 sqmm nominal cross sectioanl area multistranded copper conductor , PVC insulated unsheathed FRLS cable earth wire and connecting to earth dolly and brass screws, washers etc. complete all as specified.

M&L wiring for socket outlet 3 pin, 5 amps on independent Boards controlled by one, one way switch using 2.5 sqmm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLS cables in and including 20 mm dia or higher size PVC concealed conduits and fittings, including pressed steel terminal switch boxes , 3 mm thick bakelite sheet top cover (ISI Marked) fitted with Chromium plated brass screws & washers and 2.5 sqmm nominal cross sectioanl area multistranded copper conductor , PVC insulated unsheathed FRLS cable earth wire and connecting to earth dolly and brass screws, washers etc. complete all as specified.

S&F switch socket combination 2 in 1 multipurpose 5 pin , (6 Amps ) complete all as specified.

S&F switch piano flush type, single pole , 6 Amps, one way complete all as specified.

S&F switch socket combination 16 Amps flush type controlled by one switch complete all as specified.

S&F ceiling rose surface bakelite 65 mm x 50 mm two to three terminal suitable for 230 Volts AC 6 Amps complete all as specified.

S&F lamp holder, PVC/polycarbonate type with back plate straight or anfular suitable for batten fittings complete all as specified.

S&F LED bulb 7 watts, 240 volts, ISI marked complete all as specified.

S&F exhaust ventilation fan with louvers of sweep 300mm, metalic body, 240 volts, BEE 5 star rated, ISI marked complete all as directed by Engr-in-Charge.

S&F 01x 18 W LED batten light fittings, with T-8 tube, lighting fixture with extruded polycarbonate complete with all accessories and connection from ceiling rose with twin core twisted flexible copper conductor cable with suitable size and earthing complete, complete all as directed.

S&F 9 W LED light fitting wall mounted batten 2ft , extruded polycarbonate, enivromental friendly, heat sink provided for efficent heat dissipation and integrated electronic driver for 9 watt , 6000K including necessary connection complete all as specified and directed.

S&F security light fittings 25 watts, minimumm lumen output 100 lumen/Watt, made up of pressure dia cast housing with prismatic polycarbornate diffuser and individual LED with secondary optic and IP65 including necessary connection complete suitable for pole dia 25mm complete with all accessories including connected with twin core twisted flexible copper conductor of suitable size complete all as directed. (Make : M/s Bajaj / M/s Crompton / M/s Phillips/ M/s Havells)

S&F epoxy powder coated sheet metal enclosure for DBs, double door (when MCBs to be used), Single pole and neutral 240 V, 8 ways with mounting fitted with bus bar, DIN channel , neutral link and incoming contact complete all as specified and directed.

S&F MCB SP, 6 to 32 Amps, 'C' series 10kA, 240 Voltsand to be housed in DBs including necessry connection complete all as specified and directed. (Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating).

S&F MCB SPN 32 Amps, 'C' series 10kA, 240 Volts and to be housed in DBs complete including necessry connection all as specified and directed. (Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating).

S&F submain two single core ,6 sqmm nominal cross sectional area multistranded copper conductor FRLS cable, PVC insulated unsheathed 1100 Volts grade drawing in and including nd including suitable size PVC conduit (ISI marked), concealed, including 6 sqmm nominal cross sectional area multistranded copper conductor FRLS cable, PVC insulated unsheathed 1100 Volts grade earth wire complete all as specified.

S&F XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 10 Sqmm 2 core complete all as specified.

Excavation in trenches not exceeding 1.5m wide and not exc. 1.5m depth and getting out in hard/dense soil complete all as specified and as directed.

Returning, filling, including spreading, leveling, watering and well ramming in layers not exc. 25cmin soft/loose soil complete all as specified and as directed.

Removal of excavated soil to a distance not exc 50 m and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as directed.

Supply and lay for dry river sand filling for cable protection with a layer of 8cm deep before laying and 15cm covering above the top edge of cable after laying complete all as specified and as directed. (Note : Punned thickness shall be measured).

M&L for sub class B bricks locally available of size 25 x 12.5 x 7.5 cm laid dry width wise across the line of cable in trenches for protection of UG cable complete all as specified and directed.

M&L for earthing complete with galvanised mild steel earth plate electrode 600x600x6.0mm thick, burried directly in ground to a depth not less than 2.25 metres deep below ground level with top edge of earth plate not less than 1.5 metre below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate, using GI wire 4 mm dia as earth strip electrode bolted or rivetted to earth plate at one end and connected to equipments at another end, GI earth strip encased in and including 40 mm dia GI 'light grade' pipe from upper end of earth plate upto equipments,20 dia bore GI pipe 'light grade' as water pipe from earth chamber to upper edge of earth plate, Test point , GI funnel with wire mesh fixed on water pipe and PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in pit chamber and RCC pit cover 50mm thick precast RCC 1:2:4 type B-1, duly reinforced with MS round bars 6mm dia @ 100 c/c both ways with 10mm dia MS round bar as in lifting handles, excavation, earth work including laying the GI pipe concealed in floor/wall all as described in electric plate of SSR Part I complete all as specified and directed and testing on completion. (Note : If the desired earth resistance is not found, earthing shall be redone by the contractor at no extra cost to the department).

Supply only Window type AC 1.5 Ton capacity, 5 star rating, copper tubing, 240 volts, ISI mark complete all as specified and directed.

Supply only Refrigerator 190 Ltrs, single door, 240 volts, ISI mark, BEE rated 4 star complete all as specified and directed.

Supply only Refrigerator 231 Ltrs, Double door, 240 volts, ISI mark, BEE rated 5 star complete all as specified and directed.

Supply only water cooler 40/80 Ltrs capacity, double tap, 240 volts, ISI mark, BEE rated 5 star complete all as specified and directed.

M&L for point wiring for light point/ fan point, one light/fan/exhaust fan point controlled by one, one way switch using 1.5 sqmm nominal cross sectional area multistranded copper conductor ,PVC insulated unsheathed FRLS cables in and including 20 mm dia or higher size PVC concealed conduits and fittings of medium grade, including pressed steel terminal switch boxes, 3 mm thick bakelite sheet top cover (ISI Marked) fitted with chromium plated brass screws & washers and 1.5 sqmm nominal cross sectioanl area multistranded copper conductor FRLS PVC insulated unsheathed earth wire and connecting to earth dolly and brass screws, washers etc. complete all as specified and directed.

S&F switch piano flush type, single pole , 5/6 Amps, one way complete all as specified.

S&F ceiling rose surface bakelite 65 mm x 50 mm two to three terminal suitable for 230 Volts AC 6 Amps complete all as specified.

S&F 01x 20 W LED batten light fittings, with T-8 tube, lighting fixture with extruded polycarbonate complete with all accessories and connection from ceiling rose with twin core twisted flexible copper conductor cable with suitable size and earthing complete, complete all as directed.

S&F security light fittings 25 watts, minimumm lumen output 100 lumen/Watt, made up of pressure dia cast housing with prismatic polycarbornate diffuser and individual LED with secondary optic and IP65 including necessary connection complete suitable for pole dia 25mm complete with all accessories including connected with twin core twisted flexible copper conductor of suitable size complete all as directed. (Make : M/s Bajaj / M/s Crompton / M/s Phillips)

S&F lamp holder, PVC/polycarbonate type with back plate straight or anfular suitable for batten fittings complete all as specified.

S&F LED bulb 7 watts, 240 volts, ISI marked complete all as specified.

S&F 9 W LED mirror light fitting wall mounted batten 2ft , extruded polycarbonate, enivromental friendly, heat sink provided for efficent heat dissipation and integrated electronic driver for 9 watt , 6000K including necessary connection complete all as specified and directed.

S&F exhaust ventilation fan with louvers of sweep 300mm,240 volts, BEE 5 star rated, steel body,ISI marked complete all as directed by Engr-in-Charge.

S&F epoxy powder coated sheet metal enclosure for DBs, double door (when MCBs to be used), triple pole and neutral 240 V, 8 ways with mounting fitted with bus bar, DIN channel , neutral link and incoming contact complete all as directed.

S&F MCB SPN 32 Amps, 'C' curve, 240 Volts,ISI marked and to be housed in DBs complete including necessry connection all as specified and directed. (Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating).

S&F MCB SP, 6 to 32 Amps, 'C' series 10kA, 240 Voltsand to be housed in DBs including necessry connection complete all as specified and directed. (Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating).

S&F XLPE armoured cable 10 sqmm 2 core,1100 volts grade heavy duty cable,ISI marked passing through pipe, with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed complete all as sepcified.

Excavation in trenches not exceeding 1.5m wide and not exc. 1.5m depth and getting out in hard/dense soil complete all as specified and as directed.

Returning, filling, including spreading, leveling, watering and well ramming in layers not exc. 25cmin soft/loose soil complete all as specified and as directed.

Removal of excavated soil to a distance not exc 50 m and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as directed.

Supply and lay for dry river sand filling for cable protection with a layer of 8cm deep before laying and 15cm covering above the top edge of cable after laying complete all as specified and as directed. (Note : Punned thickness shall be measured).

M&L for sub class B bricks locally available of size 25 x 12.5 x 7.5 cm laid dry width wise across the line of cable in trenches for protection of UG cable complete all as specified and directed.

M&L for earthing complete with galvanised mild steel earth plate electrode 600x600x6.0mm thick, burried directly in ground to a depth not less than 2.25 metres deep below ground level with top edge of earth plate not less than 1.5 metre below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate, using GI wire 4 mm dia as earth strip electrode bolted or rivetted to earth plate at one end and connected to equipments at another end, GI earth strip encased in and including 40 mm dia GI 'light grade' pipe from upper end of earth plate upto equipments,20 dia bore GI pipe 'light grade' as water pipe from earth chamber to upper edge of earth plate, Test point , GI funnel with wire mesh fixed on water pipe and PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in pit chamber and RCC pit cover 50mm thick precast RCC 1:2:4 type B-1, duly reinforced with MS round bars 6mm dia @ 100 c/c both ways with 10mm dia MS round bar as in lifting handles, excavation, earth work including laying the GI pipe concealed in floor/wall all as described in electric plate of SSR Part I complete all as specified and directed and testing on completion. (Note :- If the desired earth resistance is not found, earthing shall be redone by the contractor at no extra cost to the department).

M&L for point wiring for light point/ fan point, one light/fan/exhaust fan point controlled by one, one way switch using 1.5 sqmm nominal cross sectional area multistranded copper conductor ,PVC insulated unsheathed FRLS cables in and including 20 mm dia or higher size PVC concealed conduits and fittings of medium grade, including pressed steel terminal switch boxes, 3 mm thick bakelite sheet top cover (ISI Marked) fitted with chromium plated brass screws & washers and 1.5 sqmm nominal cross sectioanl area multistranded copper conductor FRLS PVC insulated unsheathed earth wire and connecting to earth dolly and brass screws, washers etc. complete all as specified and directed.

M&L for wiring for 5 Amps socket out let on independent Boards controlled by one, one way switch using 2.5 sqmm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLS cables in and including 20 mm dia or higher size PVC concealed conduits and fittings, including pressed steel terminal switch boxes , 3 mm thick bakelite sheet top cover (ISI Marked) fitted with Chromium plated brass screws & washers and 2.5 sqmm nominal cross sectioanl area multistranded copper conductor , PVC insulated unsheathed FRLS cable earth wire and connecting to earth dolly and brass screws, washers etc. complete all as specified.

M&L for wiring for 15 Amps socket out let on independent Boards controlled by one, one way switch using 4 sqmm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLS cables in and including 20 mm dia or higher size PVC concealed conduits and fittings, including pressed steel terminal switch boxes , 3 mm thick bakelite sheet top cover (ISI Marked) fitted with Chromium plated brass screws & washers and 4.0 sqmm nominal cross sectioanl area multistranded copper conductor , PVC insulated unsheathed FRLS cable earth wire and connecting to earth dolly and brass screws, washers etc. complete all as specified.

S&F switch piano flush type, single pole , 5/6 Amps, one way complete all as specified.

S&F switch socket combination 2 in 1 multipurpose 5 pin , (5/6 Amps ) complete all as specified.

S&F switch socket combination 5/16 Amps 5 in 1 flush type controlled by one switch complete all as specified.

S&F ceiling rose surface bakelite 65 mm x 50 mm two to three terminal suitable for 230 Volts AC 6 Amps complete all as specified.

S&F 01x 18 W LED batten light fittings, with T-8 tube, lighting fixture with extruded polycarbonate complete with all accessories and connection from ceiling rose with twin core twisted flexible copper conductor cable with suitable size and earthing complete all as directed.

S&F security light fittings 25 watts, minimumm lumen output 100 lumen/Watt, made up of pressure dia cast housing with prismatic polycarbornate diffuser and individual LED with secondary optic and IP65 including necessary connection complete suitable for pole dia 25mm complete with all accessories including connected with twin core twisted flexible copper conductor of suitable size complete all as directed. (Make: M/s Bajaj / M/s Crompton / M/s Phillips)

S&F lamp holder, PVC/polycarbonate type with back plate straight or anfular suitable for batten fittings complete all as specified.

S&F LED bulb 7 watts, 240 volts, ISI marked complete all as specified.

S&F 9 W LED mirror light fitting wall mounted batten 2ft , extruded polycarbonate, enivromental friendly, heat sink provided for efficent heat dissipation and integrated electronic driver for 9 watt , 6000K including necessary connection complete all as specified and directed.

S&F exhaust ventilation fan with louvers of sweep 300mm,240 volts, BEE 5 star rated, steel body,ISI marked complete all as directed by Engr-in-Charge.

S&F epoxy powder coated sheet metal enclosure for DBs, double door (when MCBs to be used), triple pole and neutral 240 V, 8 ways with mounting fitted with bus bar, DIN channel , neutral link and incoming contact complete all as directed.

S&F MCB SPN 63 Amps, 'C' curve, 240 Volts,ISI marked and to be housed in DBs complete including necessry connection all as specified and directed. (Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating).

S&F MCB SP, 6 to 32 Amps, 'C' series 10kA, 240 Voltsand to be housed in DBs including necessry connection complete all as specified and directed. (Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating).

S&F XLPE armoured cable 10 sqmm 2 core,1100 volts grade heavy duty cable,ISI marked passing through pipe, with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed complete all as sepcified and directed.

Excavation in trenches not exceeding 1.5m wide and not exc. 1.5m depth and getting out in hard/dense soil complete all as specified and as directed.

Returning, filling, including spreading, leveling, watering and well ramming in layers not exc. 25cmin soft/loose soil complete all as specified and as directed.

Removal of excavated soil to a distance not exc 50 m and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as directed.

Supply and lay for dry river sand filling for cable protection with a layer of 8cm deep before laying and 15cm covering above the top edge of cable after laying complete all as specified and as directed. (Note : Punned thickness shall be measured).

M&L for sub class B bricks locally available of size 25 x 12.5 x 7.5 cm laid dry width wise across the line of cable in trenches for protection of UG cable complete all as specified and directed.

M&L for earthing complete with galvanised mild steel earth plate electrode 600x600x6.0mm thick, burried directly in ground to a depth not less than 2.25 metres deep below ground level with top edge of earth plate not less than 1.5 metre below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate, using GI wire 4 mm dia as earth strip electrode bolted or rivetted to earth plate at one end and connected to equipments at another end, GI earth strip encased in and including 40 mm dia GI 'light grade' pipe from upper end of earth plate upto equipments,20 dia bore GI pipe 'light grade' as water pipe from earth chamber to upper edge of earth plate, Test point , GI funnel with wire mesh fixed on water pipe and PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in pit chamber and RCC pit cover 50mm thick precast RCC 1:2:4 type B-1, duly reinforced with MS round bars 6mm dia @ 100 c/c both ways with 10mm dia MS round bar as in lifting handles, excavation, earth work including laying the GI pipe concealed in floor/wall all as described in electric plate of SSR Part I complete all as specified and directed and testing on completion. (Note :- If the desired earth resistance is not found, earthing shall be redone by the contractor at no extra cost to the department).

M&L for point wiring for light point/ fan point, one light/fan/exhaust fan point controlled by one, one way switch using 1.5 sqmm nominal cross sectional area multistranded copper conductor ,PVC insulated unsheathed FRLS cables in and including 20 mm dia or higher size PVC concealed conduits and fittings of medium grade, including pressed steel terminal switch boxes, 3 mm thick bakelite sheet top cover (ISI Marked) fitted with chromium plated brass screws & washers and 1.5 sqmm nominal cross sectioanl area multistranded copper conductor FRLS PVC insulated unsheathed earth wire and connecting to earth dolly and brass screws, washers etc. complete all as specified and directed.

M&L for wiring for socket out let on independent Boards controlled by one, one way switch using 2.5 sqmm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLS cables in and including 20 mm dia or higher size PVC concealed conduits and fittings, including pressed steel terminal switch boxes , 3 mm thick bakelite sheet top cover (ISI Marked) fitted with Chromium plated brass screws & washers and 2.5 sqmm nominal cross sectioanl area multistranded copper conductor , PVC insulated unsheathed FRLS cable earth wire and connecting to earth dolly and brass screws, washers etc. complete all as specified.

M&L for wiring for socket outlet 3 pin, 15 amps on independent Boards controlled by one, one way switch using 4.0 sqmm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLS cables in and including 20 mm dia or higher size PVC concealed conduits and fittings, including pressed steel terminal switch boxes , 3 mm thick bakelite sheet top cover (ISI Marked) fitted with Chromium plated brass screws & washers and 4.0 sqmm nominal cross sectioanl area multistranded copper conductor , PVC insulated unsheathed FRLS cable earth wire and connecting to earth dolly and brass screws, washers etc. complete all as specified.

S&F switch socket combination 5 Amps, 3 pin, Amps flush type controlled by one switch complete all as specified.

S&F switch piano flush type, single pole , 6 Amps, one way complete all as specified.

S&F switch socket combination 16 Amps flush type controlled by one switch complete all as specified.

S&F ceiling rose surface bakelite 65 mm x 50 mm two to three terminal suitable for 230 Volts AC 6 Amps complete all as specified.

S&F stepped type electronic fan regulator flush type 240 Volts ISI marked complete all as specified .

S&F lamp holder, PVC/polycarbonate type with back plate straight or anfular suitable for batten fittings complete all as specified.

S&F LED bulb 7 watts, 240 volts, ISI marked complete all as specified.

S&F ceiling fan 1200mm size , BEE 5 star rated, ISI mark, 240V, 50 Hz all as specified and directed. (Make: M/s Bajaj / M/s Crompton / M/s Havells)

S&F metal body exhaust fan with louvers of sweep 300mm,240 volts, BEE 5 star rated, ISI marked complete all as directed by Engr-in-Charge.

S&F GI pipe light grade 40 mm dia of size for road cross of cable,ISI marked all as specified and directed.

S&F XLPE armoured cable 16 sqmm 4 core,1100 volts grade heavy duty cable,ISI marked passing through pipe, with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed complete all as sepcified.

Excavation in trenches not exceeding 1.5m wide and not exc. 1.5m depth and getting out in hard/dense soil complete all as specified and as directed.

Returning, filling, including spreading, leveling, watering and well ramming in layers not exc. 25cmin soft/loose soil complete all as specified and as directed.

Removal of excavated soil to a distance not exc 50 m and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as directed.

Supply and lay for dry river sand filling for cable protection with a layer of 8cm deep before laying and 15cm covering above the top edge of cable after laying complete all as specified and as directed. (Note : Punned thickness shall be measured).

M&L for sub class B bricks locally available of size 25 x 12.5 x 7.5 cm laid dry width wise across the line of cable in trenches for protection of UG cable complete all as specified and directed.

S&F two single core, 4 sqmm nominal cross sectional area multistranded copper conductor FRLS cable, PVC insulated unsheathed 1100 Volts grade drawing in and including suitable size PVC conduit (ISI marked), concealed, including 4 sqmm nominal cross sectional area multistranded copper conductor FRLS cable, PVC insulated unsheathed 1100 Volts grade earth wire complete all as specified.

S&F 01x 20 W LED slim light polycarbonate complete with all accessories and connection from ceiling rose with twin core twisted flexible copper conductor cable with suitable size and earthing complete, complete all as directed.

S&F security light fittings 25 watts, minimumm lumen output 100 lumen/Watt, made up of pressure dia cast housing with prismatic polycarbornate diffuser and individual LED with secondary optic and IP65 including necessary connection complete suitable for pole dia 25mm complete with all accessories including connected with twin core twisted flexible copper conductor of suitable size complete all as directed. (Make: M/s Bajaj / M/s Crompton / M/s Phillips)

S&F 5 W mirror LED light fitting wall mounted batten 2ft, extruded polycarbonate, enivromental friendly, heat sink provided for efficent heat dissipation and integrated electronic driver for 9 watt , 6000K including necessary connection complete all as specified and directed.

S&F in repairs epoxy powder coated sheet metal enclosure for Vertical DBs, double door (when MCBs to be used), Triple pole and neutral 415 V, 8 ways with mounting fitted with bus bar, DIN channel , neutral link and incoming contact complete all as directed.

S&F in repairs epoxy powder coated sheet metal enclosure for DBs, double door (when MCBs to be used), Single pole and neutral 415 V, 8 ways with mounting fitted with bus bar, DIN channel , neutral link and incoming contact complete all as directed.

S&F MCB SP, 6 to 32 Amps, 'C' series 10kA, 240 Voltsand to be housed in DBs including necessry connection complete all as specified and directed. (Note : Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating).

S&F MCB SP, 40 to 63 Amps, 'C' series 10kA, 240 Voltsand to be housed in DBs including necessry connection complete all as specified and directed. (Note : Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating).

S&F MCB SPN 63 Amps, 'C' series 10kA, 415 Volts and to be housed in DBs complete including necessry connection all as specified and directed. (Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating).

M&L for earthing complete with galvanised mild steel earth plate electrode 600x600x6.0mm thick, burried directly in ground to a depth not less than 2.25 metres deep below ground level with top edge of earth plate not less than 1.5 metre below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate, using GI wire 4 mm dia as earth strip electrode bolted or rivetted to earth plate at one end and connected to equipments at another end, GI earth strip encased in and including 40 mm dia GI 'light grade' pipe from upper end of earth plate upto equipments,20 dia bore GI pipe 'light grade' as water pipe from earth chamber to upper edge of earth plate, Test point , GI funnel with wire mesh fixed on water pipe and PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in pit chamber and RCC pit cover 50mm thick precast RCC 1:2:4 type B-1, duly reinforced with MS round bars 6mm dia @ 100 c/c both ways with 10mm dia MS round bar as in lifting handles, excavation, earth work including laying the GI pipe concealed in floor/wall all as described in electric plate of SSR Part I complete all as specified and directed and testing on completion. (Note :- If the desired earth resistance is not found, earthing shall be redone by the contractor at no extra cost to the department).

M/S S M ENTERPRISE

Das and Brothers