SPECIAL REPAIR TO VARIOUS OTM ACCN AND ROOF TREATMENT OF CERTAIN BLDGS AT AIR FORCE STATION AMRITSAR CANTT

Amount

Building Work

Dismantling of brick tiles or terracing tiles single layer on roofs complete all as specified and directed

Demolition of Mud in roofs any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) etc complete all as specified and directed

M&L for APP based polymeric membrane minimum weighing 3 kg/sqm and minimum 3 mm thick reinforced with polyster non wove fabric( weight not less than 150 gms/sqm) laid on primed surface by forced application with and including approved bitumen primer as per manufacturer's instructuctions including cleaning the surfaces complete all as specified and as directed. Note: Sheet shall be five layered prefabricated Atactic Polypropyleen Polymer (APP) modified 3 mm thick membrane (weighing not less than 3 kg/sqm) reinforced with 150 gsm polyester non- woven fabric. Concrete of roof surface shall be scratched with scratched tool before finishing roof surface when the concrete surface is still green,10mm thick 1:4 cement plaster shall be laid .The roof surfaces shall be throughly wire brushed, washed, dried up and cleaned to all foreign matter and dust prior to the appliction of primer. On the dried surface one coat of approved bituminous primer, having density in the range of 0.87 to 0.89 kg/litre at 25 degree centigrade and viscosity of 40 to 160 CPS, manufactured by same manufacturer @ 0.4 litre / sqm shall be applied. APP membrane shall be laid on primed surface by torch application method after allowing 24 hours for primer to dry . Laying off APP membrane will normally be laid in length at right angle to the direction of slope. The overlaps shall be of minimum 100mm on longitudinal direction and 150 mm on the transverse direction. All overlaps shall be bonded with bitumen primer and levelled by heating the overlaps with butane torch. the treatment shall be done by the approved authorised applicatiors.

M&L for 50mm thick (average thickness) PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) mixed with water proofing compound as in padding roof to maintain slope, correction of the depressed undulaution portion and in roof kerb etc. complete all as specified and as directed.

M&L for roughening old surface of concrete roof/floors etc by picking, sweeping and washing down with water to remove dust/dirt and brushing neat cement @ 3.0 kg per sqm complete all as specified and as directed.

Material and labour for 40mm thick brick tiles laid on roof with and including 15 mm thick screed bed in CM (1:6) jointed, grouted and pointed flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement complete all as specified and as directed.

Material and labour for 40mm thick (Except Brick tiles) laid on roof with and including 15 mm thick screed bed in CM (1:6) jointed, grouted and pointed flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement complete all as specified and as directed. Note : (i) Old serviceable tiles as obtained from Serial item No. 1 here-in-before shall be reused. (ii) The cost of cleaning and washing of brick tiles for re-use, shall be deemed to be included in the unit rate quoted by the tenderer.

M&L for PCC 1:2:4 type B-1 (using 20mm graded stone aggregates) as in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and as directed

Demolition of brick work built in cement mortar incl all quoins, arches, pillars etc complete all as specified and directed .

M&L for Brick work with old size sub class "B" bricks, straight or curved on plan exc 6 m mean radius, built in CM 1:4 complete all as specified and as directed .

M&L for Demolition of reinforced cement concrete in any position and any description including cutting of reinforcement bars to facilitate demolition complete all as specified and directed.

Material and labour for reinforcement cement concrete (nominal mix) (1:1.5:3) type A-1, using 20mm graded crushed stone aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for Mild steel TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed.

Material and labour for Formwork to sides and soffits of roof beams, lintels, cantilever, shelves, splay between floor and beam etc., flat fair finished concrete surfaces, complete all as specified and directed.

Taking down cement plaster on brick or concrete surfaces etc including racking out joints hacking for key,scrubbing down with water etc (from walls and ceiling surfaces of any description) & removing debries out side the MoD land to a desiginated place earmarked by the local administration complete all as specified and as directed.

M&L for rendering 10mm thick in cement mortar (1:3) on concrete surfaces as in ceiling, finished even and smooth without extra cement complete all as specified and as directed.

M&L for rendering 15mm thick in cement mortar (1:4) mixed with water proofing compound @ 3% by weight of cement finished even and fair without extra using cement complete all as specified and directed. Note:- WPC shall be measured and paid for separately.

M&L for rendering 20mm thick in two layers (15+5mm) on concrete surfaces in cement mortar (1:4) in patches at columns, chajja, canpoy and soffits using GI chicken wire mesh with & including necessary scafolding as required at site complete all as specified and as directed.

M&L for rendering 15 mm thick in cement mortar (1:6) on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of new plastered surfaces as in ceiling and applying three coats of white wash complete all as specified and as directed.

M&L for complete removal of existing treatment and applying three coats of white wash as in ceiling complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of 1st quality water based Acrylic distemper over and including 1mm thick wall care putty to obtain smooth regular/even finish over a coat of primer complete all as specified and as directed.

M&L for complete removal of existing treatment on wall and applying two coats of 1st quality water based Acrylic distemper over and including 1mm thick wall care putty to obtain smooth regular/even finish complete all as specified and as directed.

Material and labour for applying two coats of Acrylic weather coat emulsion paint on walls/ceiling/facias/ramp Surface etc in disruptive pattern having percentage of Six- colour as 29.04% of RGB Value (143, 152, 113), 22.48% of RGB Value (112,139,86), 14.98% of RGB value (123,137,126), 13.80% of RGB Value (84,97,75), 14.15% of RGB Value (123, 137, 94) and 5.55% of RGB Value (206,193,141) as per sample approved by AGE(I) for building of height upto 7.5 meter, over and including a coat of primer of the same manufacturer complete all as specified and directed.

Material and labour for completely removal of existing surfaces and applying two coats of Acrylic weather coat emulsion paint on walls/ceiling/facias/ramp Surface etc in disruptive pattern having percentage of Six- colour as 29.04% of RGB Value (143, 152, 113), 22.48% of RGB Value (112,139,86), 14.98% of RGB value (123,137,126), 13.80% of RGB Value (84,97,75), 14.15% of RGB Value (123, 137, 94) and 5.55% of RGB Value (206,193,141) as per sample approved by AGE(I) for building of height upto 7.5 meter, over and including a coat of primer of the same manufacturer complete all as specified and directed. Note:- for item No. 25 & 26. The rate quoted by contractor is demmed to include preparation of surfaces and necessary scaffolding for painting upto required height. All safety measures will be provided by the contractor as per standard safety norms.

Supply only intergral water profing compound complete all as specified and as directed.

Dismantling floor,hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and as directed.

M & L for coloured non skid/matt finish ceramic tiles, 7 to 8 mm thick, (square/ rectangular), area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including screed bed or bedding layer of 15 mm thick in cement mortar (1:6) complete all as specified and as directed.

All as per item No 29 here-in-before but as in dado, riser & skirting over & incl 10mm thick rendering in CM 1:4 complete all as specified and as directed.

M & L for coloured non skid/matt finish ceramic tiles, 7 to 8 mm thick, (square/ rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm sq.m in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including screed bed or bedding layer of 15 mm thick in cement mortar (1:6) complete all as specified and as directed.

M&L for coloured glazed ceramic tiles of size 350 x 250 x 7mm /450x350x7 mm thick on vertical surfaces such as skirting/dado, set and jointed in neat cement slurry and pointed in coloured cement to match over and including rendering 10mm thick in cement mortar (1:3) complete all as specified and as directed.

M & L for 16 to 18 mm thick Granite stone slab (of any type) work (table rubbed and polished) in steps, jambs, urinal partitions, pillars, window- cills,cooking platforms and the like laid over & including 15mm thick screed bed in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shades complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5sq.m each complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutter from the frames) exc. 1.5sq.m but not exc. 4sq.m each complete all as specified and as directed.

Taking down shutters exc 1 sq. m and n exc 2 sq. m each complete all as specified and as directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm thick prelaminated wood grain both side PVC sheet reinforced with MS Square tube, supplying and fixing in opening as per specifications and drg, complete all as specified and as directed.

Supply and fixing factory made pre-laminated PVC door shutter (conforming to IS-4020) 30mm thick consisting of frame made out of M.S. tubes of 19 gauge thickness & size of stiles, top rail, bottom rails & lock rail all as per shown on drawings in SSR 2010 Pt II, M.S. frame shall have a coat of steel primer of approved make & manufacturer, MS frame covered with 5mm thick heat moulded pre-laminated PVC ‘C’ channel of size 30mm thick, 70mm width out of which 50mm shall be flat & 20mm shall be tapered in 45degree on the either side forming stiles and 5mm thick, 95mm wide pre-laminated PVC sheet out of which 75mm shall be flat and 20mm shall be tapered at 45 degree on the inner side to form top rail & bottom rail and 155mm pre-laminated sheet out of which 75mm shall be flat and 20mm shall be tapered on both sides to form lock rail. Top, bottom & lock rail shall be provided on either side of panel. 10mm (5mmx2mm) thick, 20mm wide cross PVC sheet shall be provided as gap inserted to top rail and bottom rail; Paneling of 5 mm thick prelaminated wood grain both sides PVC sheet to be fitted with M.S. frame welded/sealed to the stiles & rails with 5mm+2mm thickx15mm wide PVC sheet beading on inner side and joined together with solvent cement adhesive etc. An additional 5mm thick PVC strip of 20mm width is to be stuck on the interior side of "C" channel using PVC solvent adhesive, complete all as specified and directed.

S&F Pressed steel frames of Size 105 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified and as directed.

S&F Pressed steel frames for doors Size of frame 125 x 60 mm with one or more rebates including necessary fixing lugs hinges lock strike plate etc complete all as specified and as directed.

S&F 18/19 mm thick Flush shutters solid core construction, with block board core and plywood face panels, commercial type, one face is covered with decorative face veneer with lipping to match complete all as specified and as directed.

S&F 35 mm thick, 2nd class hard wood, glazed & skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. Sizes of members of shutters as specified in SSR Part I, Section 8, Clause 8.24 (a) complete all as specified and as directed.

S&F Flush shutters 30mm thick solid core construction, with block board core and and plywood face panels, commercial type on both sides with lipping to match complete all as specified and as directed.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws complete all as specified and as directed.

S&F Powder coated (thickness of powder coating not less than 50 micron) Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 Kg/m, with minimum thickness of powder coating 50 micron, including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150 mm long (1 No.), hinges type B-21, 100mm long (2 Nos), suitable handle (2 Nos.) complete shall as specified and as directed.

S&F stainless steel butt hinges medium weight of size 100mm complete all as specified and as directed.

S&F extruded aluminium alloy handles, fabricated type, anodised of size 150 mm complete all as specified and as directed.

S&F aluminium anodised, barrel tower bolts of extruded section with length of bolt 150 mm and fixed complete all as specified and as directed

S&F Mortice lock Brass vertical type, 100mm size 2 levers with two kets complete all as specified and as directed

S&F aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy with length of bolt 250 mm and fixed complete all as specified and as directed.

S&F 140mm long floor door stopper of aluminium alloy body and tongue with hard drawn steel springcomplete all as specified and as directed.

S&F in repair framed work such as grills/ grating/cooler stand etc with ends of bars shouldered and/or riveted or forged into spikes frame gurads bars barred iron, door ladders, framed balusters walk way railings frame work of water tanks and similar work complete all as specified and as directed

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with screws or beading in steel/ wooden door / window complete as specified and directed.

S&F Sheet glass 3mm thick ordinary quality and glazing with oil putty in squeres n.exc 0.5 sqm in each panes complete all as specified and as directed

S&F Aluminium (Die cast) body door closer hydraulically regulated designation 3, universal type, suitable for door shutter 851 to 1000mm in width and of weight 61 to 80 kgs complete all as specified and as directed

S&F Sheet glass 5.5mm thick ordinary quality in squeres n.exc 0.5 sqm in each panes in aluminium door and windows shutters complete all as specified and as directed

M&L for two coats of synthetic enamel paint over a coat of red oxide primer on new steel surface of any description over 10 cm width or girth not otherwise described including prepration of surface complete all as specified and as directed

All as per item No. 57 here-in-before but except primer complete all as specified and as directed

M&L for two coats of synthetic enamel paint over a coat of pink primer on new wooden surface of any description over 10 cm width or girth not otherwise described including prepration of surface complete all as specified and as directed.

M&L for machine cut kota stone slab, 20-23 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including, cutting and mirror polishing with and including 20 mm thick screed bed or bedding layer in CM 1:6 for laying floor finishes complete all as specified and as directed.

All as per item No. 59 here-in-before but as in riser of steps,dado/ pillars and vertical surfaces etc over and including 10 mm thick rendering on brick or concrete suface in CM 1:4 after taking down cement plaster on walls and racking out joints,hacking for key, scrubing down with water etc complete all as specified and as directed.

S & F in repairs vitreous china wash basin, white, flat back of size 450mm x 300mm including brackets grouted in cement mortar 1:2 in wall complete all as specified and as directed.

S&F in repair for Vitreous China wash down water closet pan ( pedestal pattern) white ( excluding flushing cistern and flush pipe) including plastic water closet seat white with jet, closed pattern with flat botton and cover and mild steel chromium plated or aluminized hinging device complete all as specified and as directed.

S & F in repair 10 ltrs capacity PVC low level syphonic action type flushing cistern including ball valve, bracket, inlet, outlet, overflow and PVC connection complete all as specified and as directed.

S&F in repair Vitreous China urinals, Fullstal type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; and including PTMT urinal spreader for fixing to 15mm bore of iron pipe complete all as specified and as directed.

S & F 32mm bore (dia of discharge pipe) waste coupling of PTMT (half or full threaded) minimum weight 32mm- 45gms complete all as specified and as directed.

S & F in repairs pillar taps cast copper alloy with capstan head, chromium plated, fancy type, screwed down high pressure, with or without lettered ‘hot’ or ‘cold’ with long screwed shanks and fly nuts, screwed for iron pipes 15mm bore complete all as specified and as directed.

S&F PVC connection 15 mm size with PTMT nuts of length 450 mm complete all as specified and as directed.

S&F PVC waste pipe flexible 32mm or 40mm bore 60cm long for WHB & Sink complete all as specified and as directed.

M&L for Galvanised iron tubing 15mm bore, medium grade, with all fittings fixed to walls or ceiling or laid in floors, in concealed pipe work including making good the chases etc in cement mortar (1:3) after fixing of pipe, including taking down of old rusted/unserviceable GI pipe complete all as specified and directed.

All as per item No. 70 here-in-before but 20 mm bore of pipe complete all as specified and as directed.

S & F in repairs bib taps, cast copper alloy, chromium plated, screwed down high pressure, screwed for 15mm bore of iron pipe or for brass ferrule complete all as specified and as directed.

S & F in repairs CP brass towel rail D type 60 Cm long and 20mm dia fixed to wall with CP brass screws and plastic cleats complete all as specified and as directed.

S & F in repairs stop valve 15 mm bore of pipe, fancy type, chromium plated with long shank and cup (Concealed Type) cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and as directed.

S & F in repairs stop valve 15 mm bore of pipe, fancy type, chromium plated cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and as directed.

S&F in repairs float valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for 20mm bore of iron pipe or brass ferrule complete all as specified and as directed.

S&F in repairs stop valves, cast copper alloy, 20mm bore of pipe , screwed down, high pressure, fancy type chromium plated, screwed, both ends for iron pipe or for unions and fixed complete all as specified and as directed.

Dismantling of CI/PVC pipe of 75/100mm dia bore fixed with cement joint complete all as specified and as directed

S & F 110 mm dia bore PVC (SWR) pipe (Type 'B') having pressure rating 6 kgf/cm2 single socketed in trenches/floors in any length with rubber ring joints complete all as specified and as directed.

S & F PVC (SWR) bend/Door bend any radius for 110 mm bore pipe incl jointing material complete all as specified and as directed.

S & F PVC (SWR) junction single, (Single T) equal or unequal for 110mm dia bore complete all as spd and as directed

S&F in repair 110 mm dia PVC (SWR ) floor trap/ nahani trap plain with grating including jointing with solvent cement complete all as specified and as directed.

S&F in repairs Rotational moulded PVC water storage tanks 500 Ltrs capacity, double walled (ISI marked) with ISI marking embossed on the tank (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified & directed.

Demolition of cement concrete (unreinforced) in ground floors/pavings n.exc 15 cm thickness (below or above the ground level) complete all as specified & directed.

M&L for 75mm thick PCC 1:3:6 type C-2 using 40mm graded crushed stone aggregate laid in 1:20 slope as in plinth protection finished even and smooth without using extra cement with and including filling of expansion joints with mastic filling complete all as specified and as directed.

M&L for 40mm thick PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate as in floors finished even and smooth without using extra cement complete all as specified and as directed.

Dismantling of wall and ceiling boards (Fibre, pulp, insulationc) or insulation boards/slabs/blankets any thickness including cover fillets etc complete all as specified and as directed.

S&F 5-6mm thick PVC hollow wall panelling consisting of wood grain printed PVC sheet inclussive of solvent cement and fixed at site on PVC frame formed by sticking high density eps (ter grade) heavy duty with tipper strip weather, water and termite proof and fire retardent complete all as specified and as directed.

S&F anodised aluminium snap grid (of size 605x605mm) frame work for false ceilings with and including galvanised iron hangers 6mm dia (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of galvanised iron flat 40x3mm size 60mm long and expansion hold fastners 12.5mm dia 40mm long complete all as specified and as directed.

S&F non asbestos fibre cement building board 6mm thick fixed or laid/inserted to timber/GI/aluminium frame work with screws and locking pins complete all as specified and as directed.

Dismantling timber scantling frame work 40sqcm and over in section complete all as specified and as directed.

Dismantling plain or corrugated asbestos cement (corrugated/semi corrugated) sheets as in roof coverings complete all as specified and as directed.

S&F 0.50mm thick Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheets of an colour approved by the AGE (I) having tensile strength of 550 Mpa as in roof coverings fixed with self tapping screws complete all as specified and as directed.

M&L for framed work as in door or gates of angle or other section with gusset plates, rails, braces etc, drilled for fixing of steel sheeting or other coverings. Doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings confirming to FE 410-W (Gde-E-250) quality A complete all as specified and as directed.

M&L for 1.25mm thick mild steel, plain, black sheet in wall cladding, steel gates and simillar work, cut to size, holes punched, including round headed screws, clout nails or rivets and fixed to framing with plain 40mm lap joints with riveted or welded seams, including bending or turning up, mitred angles etc complete all as specified and as directed.

Excavation in trenches in soft/loose soil not exceeding 1.5 meter wide and not exceeding 1.5 meter deep for laying of cables and foundation of poles etc. and getting out complete all as spceified and as directed.

M&L for galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including securing or tying at crossings with and including provision of galvanised mild steel wire, stapples or steel pins etc (each line of wire to be measured) complete all as spceified and as directed.

S&F for 300 mm x 300 mm size and 9-10 mm thick Premium quality Outdoor deck floor non skid tiles have robust surface and elegant design rectangular in shape set and jointed in neat cement slurry over and including 15mm thick screed bed in CM 1:6 complete all as specified and as directed.

Returning, filling in trenches (soil) including spreading leveling and well ramming in layers not exc 25 cm thick complete all as specified and as directed.

Removal of surplus excavated soil to a distance not exc 50 mtr and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and as directed.

S&F Fire resistant board for wall/ceiling and partition frame work complied with BS 476: Part 4, 6 & 7 EN 136 having fire resistance ranging from 30 to 60 minutes when fixed to walls, Partitions, False ceiling, Shaftwalls, Beams and column encasement, with minimum essential joints and covering of joints using jointing compound to give clean look, Size shall 595x595, 295x 1195, 595x1195 having thickness 12 to 13 mm for wall/ceiling covered with absorvative micro fiber coating on the front side and Acoustics fiber on the back side. The Fire resistant board shall be anti-sag, installed on and including GI framing/grid system/Suspenders as per the direction of Engrs-in Charge placed at 600mm center to center, as per Fire Retardant IS 15061-2002 for excellent results complete all as specified and as directed. Make:- Saint Gobian gyproc/Armstrong/Rockfon.

S&F factory made steel window 1.25mm thick box type (primer coated) ERW hollow P section of size 60mmX25mm double rebated comprises of glazed & gauged skeleton shutter (required no of gauged shutter and glazed shutters) including guard bar ERW sec 50mmX20mm and 1mm thick with two openable leaf consisting two nos sash bar of T-section 20mmX3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 60mmX25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 (Four Nos of each window) including following fitting welded to frame shutter:- Ref Drg No CEAF/STD-184-2012 Sheets 1/3, 2/3 & 3/3 (i) Hold fast,150mm long of MS flat iron 12mmX3mm made to shape-04 Nos per window (ii) Handle of Z section 20mmX25mm,100mm long-01Nos per window (iii) MS Tower bolt 150mm long-02 Nos per window (iv) Z sec 20mmX25mm,100mm long stopper -01 Nos per window (v) Cleat 55mm long of hollow square 15mmX12mm-02Nos per leaf (vi) Fabrication & fixing arrangements as Drg No CEAF/STD-184-2012 Sheets 1/3, 2/3 & 3/3 (vii) M S guard bar 08mm square bars @75mm C/C fixed horizontally. Note : Glass, wire mesh and painting shall be measured and paid separately.

INTERNAL ELECRIFICATION WORK

Taking down carefully copper / aluminum point wiring (light, fan, socket or power) complete with fittings such as switches, ceiling roses, pendants, lamp holders, bracket, light fittings, bulk head fittings, tube light fittings etc. and making good disturbed surfaces of walls, floors etc as per existing complete all as specified and directed.

M&L for Point wiring for One light / Celing fan/ Exhaust fan point/Bell point, controlled by one switch 5 Amp SP one-way complete with 1.5 Sq mm (nominal area) PVC insulated, unsheathed and multi strand copper conductor FRLSH cable (ISI marked) drawn into and including PVC concealed conduit (medium quality) and conduit fittings including 1.5 Sq mm PVC insulated unsheathed and multi stranded copper conductor FRLSH cable as earth wire to common earth and connecting to earth dolly including MS sunken box covered with 3mm thick bakelite laminated “hylem or Philips“ sheet top cover and machine made brass screw and washers etc complete all as specified and as directed Notes;- (i) For Internal wiring colour to be used as per IE rule for Phase - Red/Yellow/Blue, Neutral- Black and Earth- Green (ii) Quoted rate shall deemed to be included for Making good of disturbed surfaces with and including M&L for applyibg finishes to match with existing surfaces, (iii) Switch/socket to be measured and paid separately.

All as per item No. 106 here-in-before but wiring for one 3 pin 6 Amps socket outlet point on the same board, controlled by other switch complete all as specified and directed.

All as per item No. 106 here-in-before but wiring for one 3 pin socket outlet 6 amps independent board.

All as per item No 106 here-in-before but with 2.5 Sqmm size cable multi stranded FRLSH copper wire unsheathed for one 3 pin socket outlet 16 Amp on independent board and including 2.5 sqmm multi stranded copper conductor FRLSH cable as earth continuity wire connecting to common earth dolly completed all as specified and as directed. Note :- Sunken boxes, frame, plate etc shall be included in the quoted rate.

S & F of switch piano flush type single pole one-way 6 Ampere complete all as specified and as directed.

S & F of switch piano flush type single pole one-way 16 Ampere complete all as specified and as directed.

S & F of 6 Ampere socket outlet flush type, multi purpose suitable for 2 and 3 pins (Total 5 Pins) complete all as specified and as directed.

S & F of socket outlet two-in-one, 3 pin each suitable for 6 and 16 Ampere flush type with shuttered complete all as specified and as directed.

S & F of ceiling rose, surface bakelite, 65 X 50 mm, 3 terminals complete all as specified and as directed.

S&F of lamp holder PVC / polycorbonate type insulated body with back plate suitable for batten fitting / angle fitting complete all as specified and as directed.

S & F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as reqd heavy duty 230 volts complete all as specified and dircted.

M& L for Sub main wiring with two single core 6 sqmm (nominal area) stranded copper conductor FRLSH PVC insulated and unsheathed cable drawn in and including non metalic PVC regid conduit medium grade of suitable size with all standard fittings, concealed, including one run of continuous PVC insulated stranded copper conductor FRLSH cable 6 sqmm (nominal area) for earth continuty, including taking out and removal of old sub main wiring complete all as specified and as directed. (Note :- 2 runs of 6sqmm copper conductor phase and neutral and one run of same size earth wire including one run of PVC conduct with cutting, chasing & making good shall be measured as one unit length)

M & L for vertical type sheet steel enclouser distribution boards, double door factory made 3 phase 415 volts 4 way with 200 amps rating copper bus bar of suitable size and PVC insulated copper jumpers from the MCCB to the out going circuits (one incoming MCCB and 12 outgoing MCBs circuits) comprising of 3 phase 4 wire of suitable rating including MCCB 160 amps, 25 KA, TP, 415 volts, 50 Hz = 01 No. and 12 Nos MCBs 6-32 Amps, complete all as specified and as directed.

S & F sheet metal enclosure for DBs (Double door type) when MCBs to be used single pole and neutral 8 ways including blanking plate as required with 200 Amps rated bus bar, 240 volts fixed sunk/flush to the wall or niche complete all as specified and as directed including necessary brick work and plaster to match with the existing surface complete all as specified and as directed.

S & F MCB DP, 240 Volts, AC, B curve, 10 KA, 40 Amps (10 KA 'B' rupturing capacity) complete all as specified and as directed

S & F MCB single pole, 240 Volts, AC, B curve, 10 KA, 6 to 32 Amps (10 KA 'B' rupturing capacity) complete all as specified and as directed

S &F LED street light /security light luminaries fitting 1X35 watt LED including fixing on existing bracket made out of GI pipe light grade 32 mm dia 1.20 m long bent to shape with suitable size mild steel clamps of size 50 X 6mm with nut, bolt, & washers as required at site for fixing of street light on LT poles / wall including making connection with PVC insulated 3 single core of 1.5 sqmm size multistranded copper conductor cable complete all as specified and as directed.

M&L for earthing complete with GI earth plate electrode of size 600mm x 600mm x 6mm thick burried directly in ground vertically (depth of pit not less than 2.25 m below normal ground level), with top edge of earth plate not less than 1.5 m below normal ground level, earth plate surrounded from all sides by 15cm thick packed alternate layers of charcoal dust and common salt, electrode connections using galvanized iron strip of size 25mmx4mm thick (upto body of equipment) by means of nuts, bolts, check nuts & GI washers, connected to main switch board or main control board or test point, protected by galvanized iron pipe light grade 32mm dia bore, and watering pipe 20 mm bore GI light grade pipe with funnel & wire mesh, including all necessary excavation & earth work, PCC chamber in PCC (1:2:4) type B-1 & RCC cover, all as shown in electrical plate No 3 of MES Schedule Part-I (2009), testing on completion, including taking out old earthing materials and removal complete all as specified and directed. Note(s) :- (i) RCC pit cover shall be pre-cast of RCC (1:2:4) type B-1, 80mm thick reinforced with XPM not less than 4Kg/Sqm. (ii) PCC chamber shall be constructed 500 mm away from the edge of earth pit. (iii) Rate shall include GI strip and protection pipe of length 7.5m, GI pipe beyond 7.5m length required at site shall be measured and paid separately. (iv) Earth resistance should be less than 3 Ohm. In case the test results are not found below 3 Ohm, complete earthing will be redone without any extra cost to Govt.

Taking down existing Ceiling fan/Exhaust fan for repair & refixing the same at its old position/location, including provision of required winding, synthetic enamel paint by spraying, nuts bolts and fastner, transportation etc, complete all as specified and as directed.

Taking down existing water heater 25/35 ltrs capacity for repair/servicing & refixing the same at its old position/location, including replacenent of elements, nuts bolts and fastner etc, complete all as specified and as directed.

S&F Flame proof metalic body with metalic blades legs, ISI marked energy efficeent BEE five star rated exhaust fan , 300 mm sweep with lauvers and connecting up including provision of three core flexible copper wire of size 1.5 sqmm from ceiling rose to exhaust fan complete in all respect all as specified and as directed.

S&F LED light fittings 1x8 watt flame proof, CMRI certified for gas/vapour group of IIA & IIIB, Zone 1 & 2 and IP 65 protection with die cast aluminium housing with heat resistant toughened glass and LED tube light fixtures driver, connector etc and connecting up with three core flexible wire complete all as specified and as directed.

External Electification Works

M & L for vertical type sheet steel enclouser distribution boards, double door factory made 3 phase 415 volts 4 way with 200 amps rating copper bus bar of suitable size and PVC insulated copper jumpers from the MCCB to the out going circuits (one incoming MCCB and 12 outgoing MCBs circuits) comprising of 3 phase 4 wire of suitable rating including MCCB 125 amps, 25 KA, TP, 415 volts, 50 Hz = 01 No. and 12 Nos MCBs 6-32 Amps, complete all as specified and directed.

Supply, laying, jointing, testing and commissioning of Low Tension (LT) XLPE insulated and armoured, heavy duty, electric power cable, cross sectional area 35 Sqmm 3.5 core aluminum conductor 1100volts grade under ground cable including both side connection with cable lugs etc, laid in trenches, along poles or passing through pipes or laid under floor or through walls etc, complete all as specified and as directed. Note: Returning filling & removal of earth, sand cushioning and bricks for protection of cable shall be measured and paid separately.

M&L for sand cushioning with a layer of dry river sand and punning to provide required cover as per SSR part -I complete all as specified and as directed. Note : Punned down thickness (overall 18cm) shall be considered for measurement and payment.

Supply & laying GI pipes 40 mm dia bore, light grade with all necessary fittings laid in trenches or with walls complete all as specified and directed.

M&L for locally available, sub class `B’ bricks (old size), laid flat and dry perpendicular to the direction of cable adjacent to each other, in trenches over the cable for protection, complete all as specified and as directed.

Note: The Total amount shall subject to adjustment of credit of Rs. 1,01,308.00 for old Materials as per Schedule of Credit.

M/s Vijay Construction Co.

M/s AKG Engineers & Contractors