SPECIAL REPAIR TO BUILDING NO. ET-272 AT RANGIA AND OTHER SANCTIONED WORKS AT RANGIA AND CHANGSARI MILITARY STATION UNDER GE RANGIA

Amount

Excavating in post holes (or similar holes) each not exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering and removing surplus soil to a distance not exc. 50 m and making good surfsce in soft/loose soil, complete all as per specified and as directed by Engineer-in-charge.

M&L for Plain cement concrete type C2, 1:3:6 (40 mm graded aggregate) as in posts and struts etc complete all as per specified and as directed by Engineer-in-charge.

M&L for steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240, complete all as per specified and as directed by Engineer-in-charge.

M&L for preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as per specified and as directed by Engineer-in-charge.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws or 'J' hooks complete all as per specified and as directed by Engineer-in-charge.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws or J hooks complete all as per specified and as directed by Engineer-in-charge.

M&L for rolled mild steel Fe-410-W(Gde-E-250) quality-B for compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc., complete all as per specified and as directed by Engineer-in-charge.

Surface excavation not exc 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil, complete all as specified and as directed by Engineer-in-charge.

Excavation in trenches not exc. 1.5m wide and not exc. 1.5m deep and getting out in soft/loose soil, complete all as specified and as directed by Engineer-in-charge.

M&L for Plain Cement Concrete Type D2 1:4:8 (using 40 mm graded stone aggregate) in foundations, filling and mass concrete, complete all as specified and as directed by Engineer-in-charge.

M&L for Brickwork with subclass ‘B’ bricks, in CM 1:6 straight or curved on plan exc. 6m mean radius, complete all as per specified and as directed by Engineer-in-charge.

M&L for brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4, complete all as per specified and as directed by Engineer-in-charge.

M&L for rendering 15 mm thick in cement mortar (1:4) finished even and smooth without using extra cement on fair faces of brick work or concrete surfaces, complete all as per specified and as directed by Engineer-in-charge.

M&L for rendering 15 mm thick in cement mortar (1:6) finished even and smooth without using extra cement on fair faces of brick work or concrete surfaces, complete all as per specified and as directed by Engineer-in-charge.

Supply only water proofing compound (integral) confirming to IS complete all as per specified and as directed by Engineer-in-charge.

M&L for sand filling under floors or in foundations including watering and consolidation, complete all as per specified and as directed by Engineer-in-charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 250 mm in soft/loose soil, complete all as specified and as directed by Engineer-in-charge.

M&L for hardcore of guage not exc. 63mm deposited, spread and levelled in layers not exc. 15 cm thick, watered and rammed to a true surface of broken stone or boulders, complete all as per specified and as directed by Engineer-in-charge.

Removing excvated materials (soils) not exc. 50.00 M and deposited where directed at a level not exc. 1.50 M above the starting point in soil, complete all as specified and as directed by Engineer-in-charge.

M&L for hardcore of gauge exc. 63 mm but n.exc 100 mm, deposited, spread and levelled in layers n.exc 100mm thick, watered and rolled rammed to a true surface, complete all as specified and as directed by Engineer-in-charge.

M & L for 75 mm thick cement concrete 1:4:8 type D2 (using 40mm graded stone aggregate) as in sub base, complete all as specified and as directed by Engineer-in-charge.

M&L, 100 mm thick cement concrete type B-1, 1:2:4 type (using 20 mm graded crushed stone aggregate) as in pavement/ hard-standing surface finished fair and even, complete all as per specified and as directed by Engineer-in-charge.

M&L for forming construction joint 30 mm deep x 10 mm wide filled with sealing compound grade "A", complete all as specified and as directed by Engineer-in-charge.

S&F Coloured non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0. 11 sqm but not exceeding 0.18 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or Coloured cement to match over 15 mm thick screed bed or bedding layers in CM 1:6, complete all as per specified and as directed by Engineer-in-charge.

M&L glazed ceramic tiles (coloured) of size 300 x 200 x 6/7 mm thick on vertical surfaces such as dados, skirting, etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including backing 10 mm thick in CM 1:4 complete all as per specified and as directed by Engineer-in-charge.

S & F Soild PVC Door frame of size 50 mm x 47 mm made out of 5 mm palin colour PVC sheet reinforced with MS square tube, suppling and fixing in opening as per specification and drawing including taking down old unserviceable PVC frame with shutter, complete all as per specified and as directed by Engineer-in-charge.

M&L for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails. M.S frame shall be covered with heat moulded plain colour PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and botom rail on either side & as gap insert for tip rail & bottom rails; Panelling of plain colour PVC sheet to be fitted in the MS frame weloded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement. suppling and fixing in the frame at site as per specification & drawing, complete all as per specified and as directed by Engineer-in-charge.

S & F Vitreous China Ware Wash hand basin white, flat back, size 550 x 400 mm size (flat back or angle back type) including cutting for and pinning ends of brackets or erecting stand and waste coupling of size 32 mm and waste pipe 32 mm, etc., complete all as per specified and as directed by Engineer-in-charge.

S & F brass chromium plated tubular towel rail, 20 mm dia., D-type, 60 cm long between flanges complete all as specified and as directed by Engineer-in-charge.

S&F 15mm dia bore pillar tap cast copper alloy with capston heads chroumium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly-nuts, screwed for iron pipe complete all as per specified and as directed by Engineer-in-charge.

S&F in repair 15mm dia bore pillar tap cast copper alloy with capston heads chroumium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly-nuts, screwed for iron pipe complete all as per specified and as directed by Engineer-in-charge.

S&F 150 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and as directed by Engineer-in-charge.

S&F butt hinges 100 mm long, type C-21, medium weight, cold rolled mild steel complete all as specified and as directed by Engineer-in-charge.

S&F 150 mm long extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and as directed by Engineer-in-charge.

Supply and fix 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy, complete all as per specified and as directed by Engineer-in-charge.

M&L for second class hard wood in scantling wrought timber framed complete all as per specified and as directed by Engineer-in-charge.

M&L for preparation of new or previously untreated surfaces of wood and wood based surfaces of any description not other wise described of over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by Engineer-in-charge.

M&L for preparation of old painted surfaces of wood and wood based surfaces of any description not other wise described of over 10cm width or girth and applying one coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by Engineer-in-charge.

M&L for preparation of old painted surfaces of wood and wood based surfaces of any description not other wise described not exceeding 10cm width or girth and applying one coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by Engineer-in-charge.

M&L for preparing surfaces of wood and wood based materials new or old of any description and girth, not otherwise described and treated with two coats of creosote oil complete all as per specified and as directed by Engineer-in-charge.

M&L for precast cement concrete type C1, 1:3:6 (using 20 mm graded stone aggregate) in landings, cover slabs (for manholes etc.) shelves and similar articles with plain faces and set in cement mortar 1:4, complete all as per specified and as directed by Engineer-in-charge.

M&L for concrete bed 1:3:6 type C2 (40 mm graded stone aggregate) to drain pipes of dia 100 mm including packing under, and haunching against the sides of pipes after they are laid and tested, complete all as per specified and as directed by Engineer-in-charge.

M & L Salt glazed stoneware drain pipes laid in trenches and jointed as specified of 100mm dia pipes, screwed for iron pipe, complete all as per specified and as directed by Engineer-in-charge.

M&L for mild steel TMT bars 6 mm to 8 mm dia., cut to length, bent to shape required, in stirrups, spacers and binders and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips quality confirming to Fe-410-S 0r Fe-410-O, complete all as per specified and as directed by Engineer-in-charge.

S & F Mild steel screw bolts,(Machine made) with hexogonal or square heads at one end and screwed the other or screwed both ends, each screwed ends to be fitted with washer and one hexogonal or square nut exc. 10 cm and n.exc 15 cm long dia of neck 11 to 15 mm, complete all as per specified and as directed by Engineer-in-charge.

M&L for preparing new plastered surfaces and applying two coats of cement base paint on surfaces of walls, complete all as per specified and as directed by Engineer-in-charge.

M&L for 50 mm thick Cement concrete type C2, 1:3:6 (using 40 mm graded stone aggregate) in footpath/ hard-standing / pavings / plinth protections, finished even and smooth without using extra cement, complete all as per specified and as directed by Engineer-in-charge.

M&L for preparing new plastered surfaces and applying two coats of cement base paint on surfaces of walls, complete all as per specified and as directed by Engineer-in-charge.

M&L for preparation of new plastered surfaces of wall and applying three coats of white wash complete all as per specified and as directed by Engineer-in-charge.

M&L for preparation of new or previously untreated steel surfaces of any description, not exc.10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as per specified and as directed by Engineer-in-charge.

S & F 15 mm bore Galvanized Steel tubes, medium grade water supply pipes etc., fixed to walls and ceilings or laid in floors complete all as per specified and as directed by Engineer-in-charge.

S & F 20 mm bore Galvanized Steel tubes, medium grade water supply pipes etc., fixed to walls and ceilings or laid in floors complete all as per specified and as directed by Engineer-in-charge.

Cutting into existing steel tubing for alterations or additions of 20mm dia bore of pipes (Each cut measured) complete all as per specified and as directed by Engineer-in-charge.

S & F soap dish, vitreous China, white, of approximate size 160 x 160 x 90 mm complete all as specified and as directed by Engineer-in-charge.

S & F 15 mm bore bib tap cast copper alloy with crutch or butterfly handle, screwed for iron pipe or for brass ferrule, complete all as per specified and as directed by Engineer-in-charge.

S & F in repair 15 mm bore bib tap fancy type cast copper alloy with crutch or butterfly handle, screwed for iron pipe or for brass ferrule, complete all as per specified and as directed by Engineer-in-charge.

Supply and fix stop valves 20 mm, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, swrewed both ends for iron or for unions and fixed complete all as specified and as directed by Engineer-in-charge.

Supply and fix stop valves 15 mm, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, swrewed both ends for iron or for unions and fixed complete all as specified and as directed by Engineer-in-charge.

S&F 15mm dia PVC connection pipe with PTMT nuts of length 450mm, complete all as per specified and as directed by Engineer-in-charge.

S&F Vitreous china urinals, bowl type flat back size 465 x 355x 265 mm white (minimum) with grating and union for discharge pipe , complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal pot backing with cement complete all as per specified and as directed by Engineer-in-charge.

S&F Vitreous China wash down water closet pan 580 x 440 mm (Pedestal pattern) white complete including seat and cover, flush pipe incl all joints complete all as per specified and as directed by Engineer-in-charge.

S&F PVC 10 ltr capacity low level flushing cistern white with inlet ball valve float and braket and 32 mm bore PVC flush pipe, complete all as per specified and as directed by Engineer-in-charge.

S&F 100mm cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4), complete all as per specified and as directed by Engineer-in-charge.

Demolition of Brickwork or stone/ boulder masonry, built in any cement mortar including all quoins, arches, pillars, etc, complete all as per specified and as directed by Engineer-in-charge.

Demolition of reed, lathing, single or double, including battens and plaster or chicken wire lathing, complete all as per specified and as directed by Engineer-in-charge.

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc., complete all as per specified and as directed by Engineer-in-charge.

M&L for G.I. Wire netting 0.9 mm dia and 12 mm mesh lathing to wood or metal studding, joists, etc., in walls, ceilings, stanchions, beams, etc., including all laps, cutting and waste, complete all as per specified and as directed by Engineer-in-charge.

M&L for rendering 15 mm thick on other than fair faces of brick work or other side of lathing in cement mortar 1:6, surface finished even and smooth without using extra cement, complete all as per specified and as directed by Engineer-in-charge.

M&L for 15mm thick in two layers rendering in CM 1:4 on fair faces of brick work or concrete block surfaces finished even and smooth without using extra cement complete all as per specified and as directed by Engineer-in-charge.

Dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings, complete all as per specified and as directed by Engineer-in-charge.

S&F 6 mm thick asbestos cement, corrugated or semi-corrugated sheets in roofs, walls etc including fixing with L hooks or cranked hooks complete all as specified and as directed by Engineer-in-charge.

Fixing only Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings, complete all as per specified and as directed by Engineer-in-charge.

S&F for 6 mm thick asbestos cement two pieces adjustable serrated ridge for corrugated, or semi corrugated sheets fixed with L-type or J-type or cranked hook bolts, complete all as per specified and as directed by Engineer-in-charge.

Demolition of unreinforced cement concrete in ground floors and pavings not exc. 15 cm thickness, complete all as per specified and as directed by Engineer-in-charge.

M&L 40 mm thick cement concrete type B1, 1:2:4 (using 20 mm graded stone aggregate) as in floors, finished even and smooth using extra cement, complete all as per specified and as directed by Engineer-in-charge.

M&L for Glass dividing strips, 38 x 3 mm thick and inserted in position to confirm to design, complete all as per specified and as directed by Engineer-in-charge.

M&L for 75 mm thick Cement concrete type C2, 1:3:6 (using 40 mm graded stone aggregate) in plinth protections, complete all as per specified and as directed by Engineer-in-charge.

Dismantling unframed timber scantlings 40 sq. cm and over in section, in any position, complete all as specified and as directed by Engineer-in-charge.

Fixing only 2nd class hard wood in scantling wrought timber un-framed and fixed complete all as per specified and as directed by Engineer-in-charge.

Dismantling of unframed fillets, rails, posts, rafters, purlins etc., under 40 Sqcm in section, complete all as per specified and as directed by Engineer-in-charge.

S & F Second class hard wood plain wrought fillets square, rectangular or triangular in section, bull nosed splayed chamfered or rounded on one edge or face sectional area exceeding 13 Sqcm and not exceeding 25 Sqcm fixed with screws, complete all as per specified and as directed by Engineer-in-charge.

S & F Second class hard wood plain wrought fillets square, rectangular or triangular in section, bull nosed splayed chamfered or rounded on one edge or face sectional area exceeding 6 Sqcm and not exceeding 13 Sqcm fixed with screws, complete all as per specified and as directed by Engineer-in-charge.

Dismantling boarding, any description, fixed in any position with nails, complete all as specified and as directed by Engineer-in-charge.

Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) any thickness, including cover fillets, complete all as per specified and as directed by Engineer-in-charge.

M&L for 2nd class hardwood 50mm (Clean Sawn) boarding with butt joints fixed with nails in any situation (except flooring and skirting), complete all as per specified and as directed by Engineer-in-charge.

M&L for 2nd class hardwood 20mm (Planed both side) boarding with butt joints fixed with nails in any situation (except flooring and skirting), complete all as per specified and as directed by Engineer-in-charge.

Taking down shutters of any description not exceeding 1 Sqm each complete all as per specified and as directed by Engineer-in-charge.

Taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each, complete all as per specified and as directed by Engineer-in-charge.

S & F 30 mm thick Second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., divided into squares with plain, chamfered or rounded mitred and rebated sash bars any numbers, edges of framing plain, chamferesd or rounded, fitted with cut and mitred beads for securing glass etc., for windows and ventilators, etc are provided with stiles and rails as specified in SSR Pt I Section 8, clause 8.24 (a) complete all as per specified and as directed by Engineer-in-charge.

S&F 30mm thick, 2nd class hardwood, framed panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, supplied and fitted to chowkats complete all as per specified and as directed by Engineer-in-charge.

S & F 100 mm long medium weight, cold rolled mild steel Butt hinges complete all as per specified and as directed by Engineer-in-charge.

S & F 75 mm long medium weight, cold rolled mild steel Butt hinges complete all as per specified and as directed by Engineer-in-charge.

S&F 125mm Aluminum anodised barrel tower bolts of extruded section complete all as per specified and as directed by Engineer-in-charge.

S&F 125mm anodised aluminium handles fabricated type complete all as per specified and as directed by Engineer-in-charge.

S&F galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanized wire staples complete all as specified and as directed by Engineer-in-charge.

S & F 3 mm thick Sheet glass, ordinary quality in squares not exceeding 0.5 Sqm in each pane fixed with cut & mitred beads, complete all as per specified and as directed by Engineer-in-charge.

M&L for preparation of new plastered surfaces of wall and applying three coats of white wash complete all as per specified and as directed by Engineer-in-charge.

M&L for preparation of new plastered surfaces of wall and applying one coat of white wash complete all as per specified and as directed by Engineer-in-charge.

Preparing surfaces of wood and wood based materials, new or old, of any description and girth, not otherwise described, and treated with tar or coal tar black paint complete all as per specified and as directed by Engineer-in-charge.

M&L for sanding newly tarred or painted surfaces with clean sharp sand complete all as per specified and as directed by Engineer-in-charge.

M&L for ATT at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as per specified and as directed by Engineer-in-charge.

Taking up or down 15 mm bore steel tubing and connections, including cleaning for refixing or removal to storecomplete all as per specified and as directed by Engineer-in-charge.

S & F in repair chromium plated shower rose 125 mm size with or without swivel joints, any size, including fixing to steel pipe or union, complete all as per specified and as directed by Engineer-in-charge.

S&F 110 mm dia PVC (SWR) pipes single socketed, in any length, laid in trenches or in floors, complete all as per specified and as directed by Engineer-in-charge.

S&F 110 mm dia bore PVC (SWR) bends, complete all as per specified and as directed by Engineer-in-charge.

S&F in repair 15mm bore brass CP Wall Mixer for mixing hot and cold water (Exposed straight legs) 3-in-1 system with provision for both Hand Shower and Overhead Shower Complete with 115mm Long Bend Pipe, Connecting Legs & Wall Flange (without Hand & Overhead Shower) arrangement screwed down for iron pipe and fixed complete all as per specified and as directed by Engineer-in-charge.

Supply, fabrication and fixing window of powder coated of extrusions Aluminium section two track with two sliding shutters with Frame 63.50mm x 38.40mm x 2mm thick, Two track bottom rail for sliding of shutters 61.98mm x 29.70mm, Top and side members for sliding shutters with Aluminium section of extrusions of 29.70mm x 61.58mm, Central rail for sliding inter lock shutter section size 39.00mm x 20mm, Top and bottom of sliding shutter extrusions size 20mm x 41mm, Side rail of sliding shutters handle section of size 20mm x 39mm, 5.5mm thick tinted/frosted/plain glass with rubber gasket of suitable size, colour of powder coating decided by EIC, all hardware also powder coated by same colour, complete all as specified and as directed by Engineer-in-charge.

S&F in repair Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long including supply and fixing of E-board ceiling fixed or laid/ inserted to GI framework with screws in false ceiling including preparing surfaces and applying three coats of white wash on exposed surfaces complete all as specified and as directed by Engineer-in-charge.

S&F Toilet Roll Holder with Stainless Steel Flap including all necessary fittings complete all as specified and as directed by Engineer-in-charge.

S&F Coloured Glazed ceramic tiles 300 x 450 x 7 mm thick on vertical surfaces such as skirting, dados and risers to steps etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match with the shades of tiles over 10 mm thick screed bedding layer in CM 1:4, complete all as per specified and as directed by Engineer-in-charge.

M&L for sand cushioning layer of 40mm thick laid in layers to required gradient and slope complete all as specified and directed by Engineer-in-charge.

M&L for machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade set jointed and pointed with grey cement and no pigment, complete all as per specified and as directed by Engineer-in-charge.

M&L for reinforced cement concrete type B1 (1:1.5:3) nominal mix (20mm graded stone aggregate) in foundation, including rafts, footing foundations beams, plinth beams, pile-caps, under reamed piles & mass concrete complete all as specified and as directed by Engineer-in-charge.

M&L for reinforced cement concrete type B-1 (1:1.5:3) nominal mix (using 20mm graded stone aggregate) as in column, pillar, post & struts complete all as specified and as directed by Engineer-in-charge.

M&L for formwork for foundation footing, pile caps, bases of columns, plinth beams & similar works on vertical or batter complete all as specified and as directed by Engineer-in-charge.

M&L for form work for side of pillars, posts, columns & similar works vertical or batter complete all as specified and as directed by Engineer-in-charge.

M&L for TMT bar 10mm dia and over, cut to length, bent to shape required including cranking, bending and binding with M.S wire (annealed) not less than 0.9 mm dia or securing with clips complete all as per specified and as directed by Engineer-in-charge.

M&L for TMT bar 5mm dia and over upto and incl 8mm dia in stirrups, spacers and binders cut to length, bent to shape required including cranking bending spirally for hoping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as per specified and as directed by Engineer-in-charge.

M&L for PCC type B-l, 1:2:4 (20 mm graded aggregate) as in coping, complete all as per specified and as directed by Engineer-in-charge.

S&F rolled mild steel Fe-410-W (Gde-E-250 quality A) as in framed work for doors, gates or grill of angle or other section with gusset plates, rails, braces etc. complete, drilled for fixing of steel sheeting or other covering, doors etc. to be prepared for hanging or sliding with & including either hooks or hinges or steel hanging door fittings also fastening & fixing complete all as specified and as directed by Engineer-in-charge.

S&F mild steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with bolted or welded attachment Fe 410 W (Grade-E-250) quality-B, complete all as per specified and as directed by Engineer-in-charge.

S&F 300 mm mild steel sliding bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all as per specified and as directed by Engineer-in-charge.

M&L 20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as per specified and as directed by Engineer-in-charge.

M&L rendering 10mm thick in CM 1:4 on concrete surfaces in wall complete all as per specified and as directed by Engineer-in-charge.

S&F in repair Floor mounted coupled WC, bowl for Coupled WC with UF soft close slim seat cover, Hinges, Fixing Accessories and Accessories Set, of size 365x630x750 mm, S Trap-220mm along with cistern with cistern fittings complete all as per specified and as directed by Engineer-in-charge.

M&L for point wiring with 1.5 sqmm size (nominal area) PVC isulated unsheathed single core multi stranded FRLS copper conductor cable drawn into and incl PVC casing capping sleeves and caps of adequate width and length with all accessories and fittings like bends, elbow crosses etc with PVC round block and PVC terminal boxes with 3.00mm thick laminated sheet cover for mounting fittings etc like switches sockets and fan regulator incl 1.5 sqmm size PVC insulated multistranded FRLS copper conductor cable as earth continuity conductor and connected to earth dolly complete all as specified and as directed for one light point controlled by one switch, complete all as per specified and as directed by Engineer-in-Charge.

All as per Serial item No. 55 above but for one exhaust fan point controlled by one switch.

All as per Serial item No. 55 above but for one ceiling fan point controlled by one switch.

All as per Serial item No. 55 above but for one bell point controlled by 5 Amp bell push.

All as per Serial item No. 55 above but for one 3 pin socket 5 Amp on the same board with other switches.

All as per Serial item No. 55 above but for one 3 pin socket outlet, 15 Amps, independent, with cable 4 sq. mm (nominal size) with 4.0 sqmm size copper earth continuity conductor

All as per Serial item No. 55 above but for one 3 pin 5 Amps socket outlet independent but below the switch board of light points in the same vertical plane.

Supply and fix switch piano flush type, 5/6 Amps 230/240 volts single pole one way, complete all as specified and as directed by Engineer-in-charge.

Supply and fix ceiling rose surface backelite three terminals, PVC/polycarbonate, insulated body, complete all as specified and as directed by Engineer-in-charge.

Supply and fix LED tube light fittings with regal batten for LED, wall mounted, LED tube T8 (double side connection) 20 W LED 4', 230 V complete with all accessories internally prewired and including connecting up with twin core twisted flexible copper conductor cable from ceiling rose to tube light fitting complete all as specified and as directed by Engineer-in-charge.

PVC rectangular block for mounting, switches, sockets, fan regulator etc. with 3 mm thick plastic laminated sheet cover of size 250mm x 250 mm and 50 mm deep complete all as specified and as directed by Engineer-in-charge.

S&F sheet metal enclosure for single door SPN 2 Ways DB when MCBs to be used single pole and neutral 240 Volts, complete all as specified and as directed by Engineer-in-charge.

S & F MCB single pole and neutral, 240 volts, 6 - 32 Amps, 10 KA, complete all as specified and as directed by Engineer-in-charge.

Supply and fix in repair 1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular of 10 sqmm size with multistranded conductor complete all as specified and as directed by Engineer-in-charge.

Supply and fix Bulk head fitting in di-cast aluminium housing and frosted glass with LED 18W lamp complete all as specified and as directed by Engineer-in-charge.

Supply and fix lamp holder, PVC/Polycarbonate type including 1X12 Watt LED bulb, mounted in batten/pendant complete all as specified and as directed by Engineer-in-charge.

S&F House service bracket (Hook type) complete with 3.0m long G.I pipe 40mm dia medium grade, two nos. 90 degree bends, M.S hook and stay or guy, complete all as specified and as directed by Engineer-in-charge.

Supply and fix metallic finish exhaust fan, single phase, 230 V and 225-230 mm dia with steel bird guard to protect fan in running condition, complete all as specified and as directed by Engineer-in-charge.

M&L for earthing complete with galvanised steel earth plate electrode of size 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below ground level, connected to galvanized earth wire 4.00 mm dia by means of bolts nuts check nuts & washers of galvanized iron or steel proctected by GI pipe 15 mm bore( light grade) and watering pipe 20 mm bore GI pipe (light grade) surrounded with charcoal dust and salt in alternate layers not exc 150mm thick complete and chamber of PCC 1:4:8 type D2 using 40 mm graded stone aggregate and coping shall be in PCC 1:3:6 type C1 using 20mm graded stone agg. 50 mm thick cover of RCC 1:2:4 type B1 using 20 mm graded stone agg. reinforced with 8 mm dia MS TMT bar @ 80 mm c/c both ways including excavation and earthwork and removal of surplus soil complete all as shown in electrical plate no 5 of SSR PT 1, 1991 and earth lead connected to earthing test point (up to main switches, DBs) complete all as specified and directed by Engineer-in-charge and testing on completion. NOTE:- (I) item includes the cost of 7.5 mtr length GI pipe for protection for GI earth wire. (ii) item rates includes the cost of 7.5 mtr earth lead GI earth wire. (iii) PCC pit shall be provided at least 500mm away from the pit and not on the earth pit itself and the extra cost of additional length of watering pipe,bends,elbow etc shall be deemed included in the unit rate.

Taking down carefully aluminum/copper point wiring (light fan, socket or power) complete incl fittings and fixtures such as switches, sockets, light fittings, ceiling rose, pendants, lamp holders, shade conical, regulators etc and separating serviceable fittings for reuse in the same work and removing unserviceable fittings and fixtures with wiring cable, battens, wooden boards etc from site and making good disturbed surfaces of walls, floors, ceiling etc, complete all as per specified and as directed by Engineer-in-Charge.

Taking down main switches, DBs with sheet metal enclosure 2/4/6/8 way SPN/TPN/DBs of any type complete all as per specified and as directed by Engineer-in-Charge.

Taking down ceiling fan dismantling and painting of ceiling fan complete at site with synthetic enamel paint by spraying incl fittings with filler one coat after cleaning all dust etc incl connecting up, complete all as specified and as directed by Engineer-in-charge.

Hanging only ceiling fan of any sweep and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and as directed by Engineer-in-charge.

S & F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. including necessary electrical connection complete all as specified and as directed by Engineer-in-charge.

Supply and fix socket 3 pin 5 Amp flush type complete all as specified and as directed by Engineer-in-charge.

Supply and fix switch socket combination multipurpose 3 pin 15 Amp and 3 pin 5 amp flush type 2 in 1 complete all as specified and as directed by Engineer-in-charge.

Supply and fix lamp holder, PVC/Polycarbonate type with back plate suitable for batten fitting complete all as specified and as directed by Engineer-in-charge.

Supply and fix bell push, 5 Amp, flush type, single pole, 230 volts, complete all as specified and as directed by Engineer-in-charge.

Supply and fix Call bell ding dong muscial type, AC, 230 Volts, Single pole, complete all as specified and as directed by Engineer-in-charge.

Supply and fix LED batten 4ft long, Ultra bright, glass shell, glare free, wide angle, suitable for 20W LED tube, single side connection, complete all as specified and as directed by Engineer-in-charge.

Supply and fix LED tube light fitting single tube 1x20 watts (4 ft) (single side connection) 240 V wall mounted LED batten ultra bright LED polycarbonate tube light with high efficiancy including all accesssories and internally pre-wired complete all as specified and as directed by Engineer-in-charge.

S&F Building security light fitting, energy saving new generation of 10W LED IP65 bulk head luminaire with opal diffuser complete with LED lamp of 10W LED 6000K complete all as per specified and as directed by Engineer-in-charge.

S&F Cast iron/pressed steel terminal boxes 60mm deep for mounting mounting of DBs with 3mm thick plastic laminated sheet cover of size 300 mmX250 mm complete all as per specified and as directed by Engineer-in-charge.

S&F down rod 12mm dia made out of mild steel 900mm long complete all as per specified and as directed by Engineer-in-charge.

Supply and fix LED bulb, 7watt, Retrofit type, complete all as specified and as directed by Engineer-in-charge. Note:- The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender, from total amount of Schedule 'A'/BOQ.

M/S S.S. Construction

M/s DEBOJIT ROY

M/S NARAYAN ENTERPRISE

M/S KIRAN ENTERPRISE

Bidder Name

M/S KIRAN ENTERPRISE

M/S NARAYAN ENTERPRISE

M/S S.S. Construction

M/s DEBOJIT ROY

B S ENTERPRISE