PETTY REPAIRS TO VARIOUS B/R WORKS OF DLRL AREA UNDER AGE B/R-I HYDERABAD

Amount

Attending day to day complaint related to carpenter works like door easing, door repair, cup board repair, wire mesh/glass pane replacement of window/door, replacement of hardware items/mirror/glass shelf etc.by deploying one carpenter and mazdoor as per requirement and ordered by Engineer-In-Charge.

Attending day to day complaint related to plumbing works like repair to leakages of bib taps/stop cocks/gate valves/pillar cocks and like, repair/replacement of sanitary fittings/plumbing fittings/water tanks etc by deploying oneplumber and mazdoor as per requirement and ordered by Engineer-In-Charge.

Attending day to day complaint related to cement works like repair to floors/ wall plaster in patches etc. area nexc 0.5 sqm each complaint by deploying onemason and mazdoor as per requirement and ordered by Engineer-In-Charge.

Attending day to day complaint related to any type of welding works like welding to steel frame works/ hinges/ glazing bars etc. by deploying one welder and mazdoor as per requirement and ordered by Engineer-In-Charge.

Notes for Ser item Nos 1 to 4 :-The quoted rate of contractor shall comprise the following :- (i) Contractor shall provide sufficient skilled and unskilled manpower on requirnment basis as directed by Engineer incharge for attending and completing the complaints as per the users satisfaction. However, the number of skilled and unskilled manpower shall be increased as directed by enginner in charge depending upon the requirements/ number of complaints registered at the complaint center. In case of failure on providing sufficiet manpower by the contractor, a penalty at the rate of Rs 1000 per skilled person per day and Rs 600 per unskilled person per day shall be levied on the contractor and recovery for the same shall be affected from contractor's dues. A separate register shall be maintained by the contractor for recording the absentee details and shall be signed by both the contractor or his authorised rep and Engr-in-charge

(ii) Complaint cell for receiving complaints from users shall be opened by the contractor from 09.00 am to 5.00 pm at MES service centre of DLRL kanchanbagh in AOR of AGE B/R-I under GE (I) R&D Kanchanbagh. The complaints related to carpenter works, plumbing works, cement works and welding works against serial item Nos 1 to 4 shall be completed within 72 hours time after lodging/ receipt of complaints. Contractor shall ensure that all the complaints shall be attended and completed within above prescribed schedule/ time period, failing which, a penalty at the rate of double the quoted rate for that particular trade work/cmplaint per day till the satisfactorily completion of complaint shall be levied on the contractor and recovery for the same shall be affected from contractor's dues. A separate register shall be maintained for recording the same and shall be signed by both the contractor or his authorised rep and Engr-in-charge.

(iii) : For each complaint a separate docket slip shall be prepared by the contractor/ his representative and handed over to related tradesman, etc. for attending the complaint and after satisfactorily completion of complaint, docket slip shall be submitted to concerned executive on the date of register of complaint, which shall be got signed from the occupant and shall be produced at the time of payment to be made to the contractor. Complaints pertaining to same location and same nature consisting of replacement of maximum two fixtures in one office/ building etc.involving movement of particular tradesman shall be measured and paid as one complaint. Replacement of more than two fixtures but multiple of three fixtures or part thereof in one office/ building, etc. shall be measured as additional complaint.

(iv) : Format of docket slip and complaint register which shall be kept in complaint cell are attached as per Appendix 'E' and Appendix 'F' of tender documents. The cost of docket slips and complaint registers etc. shall be borne by the contractor and cost thereof shall be deemed to be included in quoted rates by the contractor against respective items of schedule 'A'. The complaint slip shall be prepared by the contractor or his authorised rep and handed over to the tradesmen and necessary entry shall be made in the complaint register and will be handed over to to concerned JE / the Engr-in-Charge next day. Contractor shall maint seperate register for lodging the complaints and the same shall be produced to concerned JE / Engr-in-Charge on next day.

(v) : Necessary transportations, tools, plants, ladders, etc., including nails, screws, PVC washers for bib taps/ stop cocks/ pillar cocks, cotton thread, Jumper valves, white lead, flush washers, rawel plugs and other similar minor accessories (except items mentioned against Srl item Nos 5 to 72 here in after) required to complete the jobs/complaints shall be provided by the contractor without any extra cost to the department and cost thereof shall deemed to be included in quoted rates by the contractor against respective item of schedule 'A'. (vi) : In case of welding to steel items required to rectify/ complete the complaints, the welding set and welding rods shall be provided by the contractor without any extra cost to the department and cost thereof shall deemed to be included in qouted rate of contractor against respective item of schedule 'A'. (vii) : Materials mentioned against serial item Nos 5 to 72 hereinafter required for execution of complaints shall be supplied by the contractor and paid separately under respective items of schedule 'A' as supply only.

Supply only PVC waste pipe 32mm dia plain (Make : Prayag, Symet) of standard length/size suitable for WHB.

Supply only PVC waste pipe 40mm dia plain (Make : Prayag, Symet) of standard length/size suitable for Urinal.

Supply only CP waste coupling, 32mm dia bore (Make: Prayag, Prima, Jainko, Parko) suitable for wash basin.

Supply only PVC seat cover white in colour closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device (for EWC / Anglo Indian type WC).

Supply only M-seal in 100 grams packet.

Supply only PVC connections 15mm size with PTMT nuts of length 450mm

Supply only PVC connections 15mm size with PTMT nuts of length 600mm

Supply only 15 mm bore, Medium grade', galvanised tube in short lengths.

Supply only 20 mm bore, Medium grade', galvanised tube in short lengths.

Supply only 25mm bore, Medium grade', galvanised tube in short lengths.

Supply only 15mm dia GI fittings ( nipples, elbows, reducers, Tee, sockets, unions and tank nipples etc )

Supply only 20mm dia GI fittings ( nipples, elbows, reducers, Tee, sockets, unions and tank nipples etc ) complete all as directed.

Supply only health faucet CP brass for 15 mm dia pipe with 1.25 metre long flexible tube and wall hook

Supply only two way CP brass Bib taps 15mm dia with capstan head and flange

Supply only 15mm dia CP cast copper alloy pillar taps, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts.

Supply only 15mm dia angle cock fancy type, cast copper alloy, chromium plated screwed down high pressure with crown or capstan head.

Supply only CP brass Bib taps 15mm dia fancy type with capstan head and flange

Supply only 32 mm dia PVC flush pipe suitable for low level PVC flushing cistern.

Supply only 10 ltrs capacity PVC flushing cistern low level with inlet, ball valve, float, handle.

Supply only PVC water tank cover of any size and capacity.

Supply only CP push button cock of 15 mm dia cast copper alloy, screwed for iron pipe.

Supply only 15 mm dia CP connection pipe 600 mm long for urinals

Supply only urinal spreader CP for fixing with 15 mm dia pipe.

Supply only vitreous china urinal, half stall type, white

Supply only Vitreous china wash hand basin , white, flat back, of size 550x450mm.

Supply only stainless steel grating of size 100 mm with or without hole

Supply only gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe, suitable for 20mm bore

Supply only 20mm dia ball valve high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe (Minimum weight 210gms)

Supply only gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe, suitable for 25mm bore

Supply only 25mm dia ball valve high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe (Minimum weight 210gms)

Supply only vitreous china squatting pan "orissa" pattern of size 580x440mm white with integral foot rest

Supply only vitreous china wash down water closet pan (pedestal pattern) (EWC)

Supply only Galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.40mm

Supply only Pozzolana portland Cement (PPC), in 50 Kg bag.

Supply only White cement, ISI marked, in 1 Kg packing

Supply only Fine sand

Supply only Dr fixit liquid Integral water profing compound

Supply only 12.5 mm graded stone aggregate

Supply only Mild steel butt hinges medium weight,cold rolled, ISI marked, 100mm long .

Supply only Aluminium alloy, anodised, sliding door bolt, 300 mm long, ISI marked, with hasp, staple (bolt type) bolt not less than 16mm dia including bolts and nuts

Supply only Aluminum anodized, barrel tower bolts of extruded section 200mm long, ISI marked

Supply only Aluminum anodized, barrel tower bolts of extruded section 150mm long, ISI marked

Supply only Aluminum handles, fabricated type, anodized 100mm long, ISI marked.

Supply only Aluminum handles, fabricated type, anodized 150 mm long, ISI marked.

Supply only floor door stopper 100 mm size of aluminium alloy body and anodized.

Supply only glass 3mm thick plain of size as per site requirement.

Supply only glass 3mm thick pin head/figured of size as per site requirement.

Supply only glass 5.0 mm thick plain of size as per site requirement.

Supply only oil putty.

Supply only 18/19 mm thick pre-laminated particle board laminated both sides, exterior grade, ISI marked.

Supply only aluminium cleat of size 30x32x3 mm for fixing door / windows.

Supply only Neoprene/EPDM gasket for fixing glass in door / windows.

Supply only aluminium beading for fixing glass in door / windows.

Supply only 100 mm mortice lock with 6 levers for aluminium door

Supply only top pivots for aluminium doors.

Supply only aluminium (extruded section body) door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg

Supply only 2nd class hard wood plain fillets, square, rectangular or triangular in section, clean sawn, of size exc 6 Sqcm and nexc 10 Sqcm in cross section

Supply only silicon sealant for upvc windows, acp cladding complete all as specified. Note :- Materials supplied against item no 5 to 62 by the contractor shall be deposited first in store yard of AGE B/R -I and same shall be issued by the department to the contractor/his authorised rep on daily basis as per nature of complaint and as required at site. A register shall be maintained by the contractor or his authorised rep for the stores / materials supplied by the contractor to the department and then issued by the department to the contractor on daily basis. The register shall be kept in the custody of concerned JE and shall be produced to GE office at the time of making payment of RARs/ final bill to the contractor.

Cleaning and removing all scale and dirt etc from water tanks of capacity exceeding 500 ltrs and not exceeding 1000 ltrs from mouths of circulating pipes etc complete and writing date of cleaning by synthetic enamel paint on all tank, after cleaning, size of letters shall be 50mm in height and text shall be “TANK CLEANED ON DD/MM/YYY” complete all as specified.

Cleaning and removing all scale and dirt etc from sevice water tank of capacity exceeding 1000 ltrs but not exceeding 2000 ltrs and from mouths of circulating pipes,Date of cleaning to be written in synthetic enamel paint on all tank, after cleaning, size of letters shall be 50mm in height and text shall be “TANK CLEANED ON DD/MM/YYYY etc complete all as directed.

Complete removal of trees/plants, upto roots growth on bldg's roofs, chajjas, at junctions of pipe line fixed on walls and walls coming on bldgs and removing the material (Branches and plants ) to outside MOD land complete all as directed Note : Work to be carried out up to 04 storey building.

M&L non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) first quality area of each tile exceeding 0.11 but not exceeding 0.18 sqm, in floors etc jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles laid on and including 20 mm thick screed bed in cement mortar 1:6 including dismantling existing tiles with screed bed complete all as directed.

M&L Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles laid on and including 20 mm thick screed bed in cement mortar 1:6 including dismantling existing tiles with screed bed complete all as directed.

M&L Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in skirtings etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles laid on and including 10 mm thick screed bed in cement mortar 1:4 including dismantling existing tiles with screed bed complete all as directed.

M&L for glazed ceramic tiles of size 300x450x7 mm thick vertical surfaces such as skirting/dado jointed in neat cement slurry and pointed with white or coloured cement to match the colour of the tiles laid on and including 10mm thick rendering in cement mortar 1:4 including dismantling of existing tiles along with a backing coat complete all as directed.

M&L for Granite (of any type) tiles 18 to 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting,rounding edges and polishing laid on and including 15mm thick screed bed in cement mortar 1:6 including taking down existing stone slab/ tile complete all as directed.

S&F factory made uPVC top hung glazed and wire gauzed ventilator made of frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and glazed shutter with plain glass 3 mm thick pin head/frosted glass alongwith mosquito proofing shutter with stainless steel wire cloth 0.254 mm (30 gauge) dia of steel wire and 0.95 mm width of aperature,single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, Reinforced with G/J/U/O shape galvanised MS section considering structural/wind load requirements. Ventilator to be provided with proper operative and locking hardware mechanism, including taking down old ventilators all as specifed.

Supply & fixing of UPVC windows or UPVC framed portion 3 track sliding window with two glazed and one wire mesh sliding shutters of profile width of frame 50 mm to 60 mm, limit thermal conductivity to l.3 Kcal/sqm/hr centigrade, sound insulation up to 4-0 bds, Density, 1.46 gm/ml, Tenstile strength - 43.9N/sqmm, % Elongation at break - 215, Tenstile mpduls - 2840N/Sqmm, Flexural strength - 51N/sqmm, Heat aging at 150 degrees - No surface defect, Thickness - 2 mm, Flexural moduls elasticity 2200N / sqmm, double baskets & wool pile on window, multi point gear locking at different sides of frame, anti lift device on slide windows with temper proof screws with and including glazed shutter fixed with 5 mm thick glass & wire mesh shutter with stain less steel wire cloth 304 grade stainless steel with 0.254 mm (30 gauge) dia of steel wire and 0.95 mm width of aperature complete incl 3.00mm glass incl taking down old down old window complete all as specified. all as directed .

M&L for 75mm thick plain cement concrete1:3:6, type C1 (using 20mm graded stone aggregate) as in plinth protection including providing 10mm thick joints filled with bituminous & sand mixture (1:7) at not exc 3.00 mt intervals & at corners and finished even and smooth without using extra cement including demolition of existing concrete complete all as directed.

M&L cement concrete tiles 30cm x 30cm x20 mm thick with grey cement and pigment set jointed and pointed in neat cement slurry in floors laid over 15 mm thick screed or bedding layer in CM 1:6, including dismantling existing floor tile of any descrption complete all as directed. Make : NAVEEN/SPARTEK/NITCO

Dismantling timber scantling 40 sq cm and over in section, in any position, framed work

Dismantling timber scantlings in fillets,rails,posts,rafters,purlins etc under 40 sq cm in section, in any position unframed work.

S&F MS framed work as in tubular trusses, purlins, posts and the like fixed with angle cleats and connecting plates etc. including necessary cutting and welding etc fixed in position as specified.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of approved colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws including dismantling existing sheet of any description all as directed.

S&F in repairs Pre- painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in valley gutters, fixed to existing sheeting supports including dismantling existing sheet of any description and necessary scaffolding etc all as specified and as directed.

M&L for prepration of new steel surfaces of any description not other wise described over 10 cm width or girth and applying two coat of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

S&F aluminium anodised snap grid frame work for false ceiling grid size 605x605 mm with runners aluminium anodised main Tee of section 35x35x1.5 mm thick, cross Tee of section 25x25x1.5 mm thick and aluminium anodised angle of size 25 mm x 1.5 mm thick section fixed along side of wall including hanging from ceiling with 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long complete incl dismantling old false ceiling all as specified

M&L for providing 12mm thick Gypsum board as in ceiling fixed with screw as per manufacturers instructions and finished with two coats of plastic emulsion paint over a coat of primer on exposed surfaces complete all as specified.

M&L for providing 10 mm thick PVC insulation false ceiling tiles with EPS stuck to 1 mm plain PVC sheet suitably placed in false ceiling grid made suitable to fix tiles as per manufacturer's instructions, fixed at any height complete all as directed.

S&F brass cutting letters of size 300mm high and 25mm wall thickness, Appolex laquer coated including soldering with lead, buffing and colouring with standard colour ISI standard, MRF brand fixed on existing ACP/ any type of wall surfaces with brass bolts and nuts complete all as directed.

S&F brass DRDO logo round of size 600mm high and 25mm wall thickness, on and including circular brass sheet engraving complete logo, Appolex laquer coated, including soldering with lead buffing and colouring with standard colour ISI standard, MRF brand fixed on existing ACP/ any type of wall surfaces with brass bolts and nuts complete all as directed.

S&F stainless steel grade 304 railing 68mm dia hand rail and 3 Nos 16mm dia horizontal rails and 40mm dia balusters fixed at 900 mm centre to cnetre with clamps and dash fastener incl newel post of 75 mm dia with spherical cap fixed at starting and terminal point of railing incl taking down old stair case railing of any description complete all as specified.

S&F PVC (SWR) pipes,150 bore of pipe, single socketed, in any length with rubber ring joints, fixed as in rain water pipes /spouts etc including making necessary holes in walls or parapet and making good with cement mortar 1:4 and taking down old rain water pipe of any description and in any position complete all as specified and directed.

S&F in repairs 150mm PVC (SWR) bends any radius complete all as directed

M&L for rotational moulded triple layered polythene water storage tank (cylindrical vertical with threaded lid) hoisted and fixed in position all as specified in SSR part I capacity of tank 500 ltrs including dismantling existing damaged PVC tank complete all as directed.

M&L for rotational moulded triple layered polythene water storage tank (cylindrical vertical with threaded lid) hoisted and fixed in position all as specified in SSR part I capacity of tank 1000 ltrs including dismantling existing damaged PVC tank complete all as directed.

Taking down chowkats or frames but with shutters (with out taking off shutter from the frames) Exc 1.5 sqm but n. exc 4 sqm each complete all as specified and directed.

Taking down shutters of any description exc 1 Sqm and n exc 2sqm each complete all as specified and directed.

Supplying & fixing solid PVC door frames of sizes 50mm x 47mm made out of 5mm single side prelam PVC sheet used instead of plain colour PVC sheet & edges will be painted to match with prelam sheet reinforced with MS Square tube complete all specified and as directed.

S & F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat moulded prelam PVC "C" channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelam colour PVC sheets for top rail , lock rail and bottom rail on either side and as gap insert for top rail and bottom rail , both side prelam PVC sheet used insted of plain colour PVC sheet. Stile and rail feathered at edges paneling of prelam solid sheets 10 mm thick to be fitted in the MS framewelded, sealed to the stiles and rails with suitable PVC sheet beading , and jointed together with solvent cement complete all as specified in SSR Part -II.

S&F factory made 30mm thick flush shutters, solid core construction,with particle board core and plywood face panels,commercial type, complete all as specified and directed.

Supply and fixing Mild steel butt hinges medium weight, cold rolled, 100mm, ISI marked, fixed with stainless steel screws complete all as specified and directed.

Supply and fixing 150mm long aluminium anodised barrel tower bolt, extruded section, fixed with stainless steel screws complete all as specified and directed.

Supply and fixing 200mm long aluminium anodised barrel tower bolt, extruded section, fixed with stainless steel screws complete all as specified and directed.

Supply and fixing 200 mm size extruded aluminium aluminium alloy handles fabricated type, anodised fixed with stainless steel screws complete all as specified and directed.

Supply and fixing 250 mm aluminium alloy, anodised sliding door bolt with hasp staple (bolt type) fixing clips of sheet, cast or extruded setions and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed with stainless steel screws complete all as specified and directed.

M&L for interlocking machine pressed precast concrete paver block of approved tint, shape and size confirming to IS 15658-2006 of 60 mm thickness M-30 Grade, as in floors/pavings laid over 40 mm thick sand cushioning layer including dismantling existing floor tile of any descrption complete all as specified. Make : NAVEEN/SPARTEK/NITCO

sandhya enterprises

KIRAN CONSTRUCTIONS

Anjana corporation

Ravi Enterprises

sri vishnu enterprises

Venkat Sai Enterprises

S Anjan Reddy