Construction of proposed new Medical College at Biswanath District, Assam

Amount

EARTH WORK Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. (A) Up to a depth of 2.00m below the existing ground level. (a) In ordinary soil

(B) Extra over item no.1.1(A) above for each 1m depth or part thereof beyond the initial depth of 2m BELOW GROUND 2.00 M TO 3.00 M

Raising low site around the building with approved soil obtained from outside by truck carriage including breaking clods, dressing etc. complete including paying necessary forest royelty, sales tax, land compensation, municipal gate fees, if any monopoly duty etc. (profile measurement to be taken and 12.5% deduction for shrinkage to be made from total quantity) etc. complete as directed and specified. (b) Other than Guwahati city

With Extra lead for 8km per km truck carriage for sand gravel beyond the initial lead of 8 km.

Earth/ sand filling in plinth in layers not more than 150mm thick including necessary carriage, watering, ramming etc. complete as directed and specified including payment of land compensation, forest royalty, sales tax and other duties and taxes as may be necessary. (c) With river sand or silt (predominantly non plastic) by truck carriage including loading and unloading.

CONCRETE WORK Stone Pile Providing stone piles of required diameter and length in ordinary / dense soil etc. using 25 mm dowm graded stone aggregate or river gravel including cost of boring including watering, ramming etc. as required, Cost of T&P complete as directed and specified by the department. iii) Pile Dia 350 mm

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). (b) In prop 1cement: 4 sand :8 coarse aggregate by volume

Providing and laying 25mm thick damp proof course with cement concrete in prop 1:1.5:3 with graded stone agg. of 10mm down nominal size including providing approved damp proof admixture in proportion as recommended by the manufacturer including curing etc. complete as directed.

Applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

REINFORCED CEMENT CONCRETE WORKS Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately). Using Batching Plant/ RMC/ Truck mounted batching plant including Transit Mixer and Concerete Pump. (P)Using admixture, plasticizer etc. In Sub Structure M-25 grade concrete

M-30 grade concrete

In Super Structure M-25 grade concrete Gr. Floor to Top

d) M30 grade concrete Gr. Floor to Top

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in: Foundation, footings, bases of columns, pile cap, raft and mass concrete works etc. (a) Using 38mm thick plank

Providing form work of 12mm thick Plywood Board so as to give a rough finish including centering, shattering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in situ reinforced concrete and plain concrete work in: Columns, Pillars, Posts & Strut of square/ rectangular/ polygonal in plan or any shape like Tee/L etc. having plane vertical face Upto Gr. Floor

Extra for each subsequent floor or part thereof above the First Floor level 1st Floor

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

8th Floor & TERRACE FLOOR

Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties. (a) For depth not exceeding 1.0M. Upto Gr. Floor

Extra for each subsequent floor or part thereof above the First Floor level 1st Floor

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

8th Floor & TERRACE FLOOR

Flat Surfaces such as soffits of suspended floors, roofs, landings, cantelever slabs, chajjas, balconies and the like. (a) Floors etc. upto 200mm in thickness. Upto Gr. Floor

Extra for each subsequent floor or part thereof above the First Floor level 1st Floor

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

8th Floor & TERRACE FLOOR

Vertical surface such as walls (any thickness), parapet walls, partitions and the like including attached pilasters, butresses, plinth and string courses and the like. Upto Gr. Floor

Extra for each subsequent floor or part thereof above the First Floor level 1st Floor

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

8th Floor & TERRACE FLOOR

Vertical ties, fins, sun breaker, louvers, bands, dropwalls etc. Upto Gr. Floor

Extra for each subsequent floor or part thereof above the First Floor level 1st Floor

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

8th Floor & TERRACE FLOOR

Staircase with sloping or stepped soffits including risers and stringers but excluding Landing. Upto Gr. Floor

Extra for each subsequent floor or part thereof above the First Floor level 1st Floor

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

Extra for each subsequent 1.0M height or part thereof beyound the initial height of 4.0M as mentioned in item no. 3.2.1

Providing form work of 12mm thick Plywood board and removal of the same in edges of slabs and breaks in floors and walls etc. of in-situ reinforced concrete works upto first floor level. (a) Thickness not exceeding 200mm. Upto Gr. Floor

Extra for each subsequent floor or part thereof above the First Floor level as mentioned in item no. 3.2.3(a). 1st Floor

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

8th Floor & TERRACE FLOOR

Extra for shuttering in circular work (20% of respective centering and shuttering items) in Columns.

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Providing cast in-situ machine driven reinforced cement concrete piles of required bore-diameter, bulb diameter, lengths and with reinforcement as per specifications and drawings including using of Bentonite solution. (Reinforcement to be measured and paid seperately as per item no. 21.4.1) C) UNIFORM PILE iii) Pile dia 400 mm

v) Pile dia 500 mm

Demolishing R.C.C./ P.C.C. pile head of different diameters carefully without disturbing the remaining portion of the pile including opening out of the pile head to be demolished by excavating the earth upto required depth and clearing the debris as directed.

PILE TESTS Initial test for test loading to 2 times the specified safe working load including construction of any test pile cap and dismantling the same after completion of test. (Rate for Safe working Load)

Routine test for test loading to 1.5 times the specified safe working load including construction of any test pile cap and dismantling the same after completion of test. (Rate for Safe working Load)

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level) a) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL (i) TMT Corrosion resistant steel (CRS) reiforcement bar Gr. Floor

1st Floor

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

8th Floor/ Terrace

Supplying, fitting and fixing in position reinforcement bars conforming to relevent IS code, for reinforced cement concrete works in piles including straightening, cleaning, cutting and bending to proper shapes and length as per specifications and drawings. The rings should be welded with vertical reinforcements as per specified IS codes of practice. (Inclusive of lap length, hook, chair, bend, anchor...etc) (A) TMT bar made of Primary producer (From Primary producer)

Providing precast cement concrete Jali 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 6mm nominal size ), reinforced with 1.6 mm dia mild steel wire, including centering and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement: 3 fine sand) etc. complete, excluding plastering of the jambs, sills and soffits. 40 MM THICK

Providing precast cement concrete Jali Element 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 6mm nominal size ), reinforced with 1.6 mm dia mild steel wire, including centering and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement: 3 fine sand) etc. complete, over top of column of boundry wall. 40 MM THICK

BRICK WORK Providing soling in foundation and under floor with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete. (a) Brick on flat soling.

(b) Brick on edge soling

Brick work in cement morter with 1st class brick including racking out joints and curing complete as directed. (I) In Sub-structure upto plinth level including dewatering if necessary (d) In proportion 1:6.

Brick work in cement morter with 1st class brick including racking out joints and curing complete as directed. (II) In superstructure above plinth level up to 1st floor level. (d) In proportion 1:6. Gr. Floor

1st Floor

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

8th Floor/ Terrace

Brick work in cement morter with 1st class brick including racking out joints and curing complete as directed. (II) In superstructure above plinth level up to 1st floor level. (b) In proportion 1:4.(1 cement:4 sand) Gr. Floor

1st Floor

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

8th Floor

7th Floor/ Terrace

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

Extra for brick work / AAC block masonry / Tile brick masonry in superstructure above floor V level, for each four floors or part thereof by mechanical means.

PRE CONSTRUCTION ANTI - TERMITE TREATMENT Pre construction anti - termite treatment at the bottom of foundation pits and walls on either side up to a height of 300mm from bottom of the excavation made for column plinth beam, wall, trenches etc. by applying the emulsion @ 5 (five) litres per square meter of the surface area before starting construction work (supplying of necessary tools and accessories by the contractor) as per the direction of the Department complete. b) with aqueous emulsion having concentration 1:499 with Premise 350 SC (Imidachloprid 30.5% SC) and water, i.e. 0.07% solution.

Pre construction anti - termite treatment in the back fill in immediate contact with the foundation structure after completion, column, wall etc. to a depth of 450mm and width 300mm (when required refill in 200mm thick layers) applying the emulsion @ 5 (five) litres per square meter towards the concrete and masonry walls so as to ensure earth in contact with the structure well treated - with chemical (supplying of necessary tools and accessories by the contractor) as per the direction of the Department complete. b) with aqueous emulsion having concentration 1:499 with Premise 350 SC (Imidachloprid 30.5% SC) and water, i.e. 0.07% solution.

Pre construction anti - termite treatment by applying in the entire levelled area after plinth filling and before laying floor by applying the emulsion @ 5 (five) litres per square meter of the surface to be spread with light rodding so as to ensure proper absorption by the filled up earth (supplying of necessary tools and accessories by the contractor) as per the direction of the Department complete. b) with aqueous emulsion having concentration 1:499 with Premise 350 SC (Imidachloprid 30.5% SC) and water, i.e. 0.07% solution.

Pre construction anti - termite treatment by applying in the junction of walls, column with the floor before laying floor and after operation of item no. 26.1.3 above making a channel 30mmx30mm all over the walls and making rod holes @ 150mm apart up to ground level below and applying emulsion @ 11 litres per square meter of vertical plinth wall surface inside the building so as to soak the soil with the emulsion up to the ground level and refill the holes and channel with the original materials obtained in making channels (supplying of necessary tools and accessories by the contractor) as per the direction of the Department complete. b) with aqueous emulsion having concentration 1:499 with Premise 350 SC (Imidachloprid 30.5% SC) and water, i.e. 0.07% solution.

Pre construction anti - termite treatment by applying the soil along the external perimeter of the building (after construction completed) to a distance close to the plinth wall as specified and as directed by the deptt. up to a depth of 300mm making rod holes along the line @ 150mm apart to a depth of 300mm and applying emulsion @ 4.5 litres per running meter ensure moistening of the soil with emulsion (supplying of necessary tools and accessories by the contractor) as per the direction of the Department complete. b) with aqueous emulsion having concentration 1:499 with Premise 350 SC (Imidachloprid 30.5% SC) and water, i.e. 0.07% solution.

DOOR WINDOW WORK Providing and fixing anodised aluminium framed double leaf doors of approved brand with styles size 45mm x 48mm x 3.2mm, top rails 50mm x 45mm x 2.5mm, lock rails 48 mm x 45mm x 2.5mm, bottom rails 100mm x 45mm x 2.5mm fitted with tapper clips of size 20mm x15mm x1.2mm complete with automatic floor mounted door closure, butterfly type handles, special cylindrical lock, concealed type aluminium tower bolt,neoprene dryset rubber gusket, door felt gusket, etc.complete as directed by the Department at all levels. A (i)5mm thick frosted glass and 12mm thick prelaminated particle board

Providing and fixing coloured anodised aluminium framed single leaf door of approved brand with styles size 45mm x 48mm x 3.2mm, top rails 50mm x 45mm x 2.5mm, lock rails 48 mm x 45mm x 2.5mm, bottom rails 100mm x 45mm x 2.5mm fitted with tapper clips of size 20mm x 15mm x 1.2mm complete with automatic hydraulic floor mounted door closure, butterfly type handles, special cylindrical locks, concealed type tower bolt, neoprene dryset rubber gusket, etc.complete as directed by the Department at all levels. (i)5mm thick frosted glass and 12mm thick prelaminated board

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) A powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5.50 mm thickness With float glass panes of 4.0 mm thickness (weight not less than 10 kg/ sqm)

With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm)

Providing and fixing stainless steel (SS 304 grade) adjustable friction windows stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per direction of Engineerin-charge complete. 355X19 MM

Supplying and installing uPVC- Fixed Windows made out of Lead free green profile having "GREENLINE" mark of BIS standard uPVC multichambered sections of wall thickness 2.4mm with corners fusion welded, fully reinforced with galvanized steel 1.5/2mm including glazing bead , grooving bead, drain cap, fisher screws, packing pieces, necessary stainless steel screws etc. complete as directed. The windows must be installed complete with all kinds of ironmongery including EPDM gaskets, bridging wedges and glass packers and with suitable water draining system. Application of Silicon sealant from inside / outside of dowcorning / GE or equivalent. With 5mm clear glass (a) Fixed window using uPVC sections of size 58mm x 52mm x 2.4mm thick wall for frame and 58mm x 68mm having 2.4mm thick wall for glass sash having reinforcement of 1.5mm thick in both frame & sash. (WINSTA KOMMERLING/ FINESTA/ ENCRAFT)

Supplying and installing uPVC- Sliding Windows made out of Lead free green profile having "GREENLINE" mark of BIS standard uPVC multichambered sections of wall thickness 2.4mm with corners fusion welded, fully reinforced with Galvanized steel 1.5/2mm including interlock profile, glazing bead, grooving bead, brush seal, aluminum sliding track, stainless steel rollers, sealing wedge block, Espag, int handle, pop up handle, keeper, drain cap, fisher screws, packing pieces with all necessary stainlessness screws etc. complete as directed. The windows must be installed complete with all kinds of ironmongery including EPDM gaskets, bridging wedges and glass packers and with suitable water draining system. Application of silicon sealant from inside / outside of Dowcorning / GE or equivalent. With 5mm clear glass (a) 2 Track Sliding Window with Flyscreen using uPVC section of sizes 88mm x 50 mm x 2.4mm thick wall for frame with inbuilt flyscreen track, 37mm x 61mm x 2.4mm thick wall for glass sash, 25mm x 49mm x 2.4mm thick wall for flyscreen sash having 1.5mm thick reinforcement, Interlock: 43mm x 23mm (Glass Panel) (WINSTA KOMMERLING/ FINESTA/ ENCRAFT) (i) 2-Panel with 5mm clear float glass

(ii) 4-Panel with 5mm clear float glass

Supplying and installing uPVC- Casement Windows made out of Lead free green profile having "GREENLINE" mark of BIS standard uPVC sections of wall thickness 2.4mm, multichambered with corners fusion welded, fully reinforced with Galvanized steel 1.5/2mm including glazing bead, folding gasket, glazing gasket, friction stay, Espag handle, Espag, keeper, drain cap, run up block, fisher screws, packing pieces with all stainless steel screws complete as directed. The windows must be installed complete with all kinds of ironmongery including EPDM gaskets,bridging wedges and glass packers and with suitable water draining system. Fittings ROTO / GQ or Equivalent. Application of Silicon sealant from Inside / Outside of Dowcorning / GE or equivalent. a) Single leaf Side hung Window using uPVC section of size 58mm x 57mm x 2.4mm thick wall for frame, 58mm x 68mm x 2.4mm thick wall for glass sash. With 5mm clear float glass (WINSTA KOMMERLING/ FINESTA/ ENCRAFT)

(d) Single leaf Top hung Window using uPVC section of size 58mm x 57mm x 2.4mm thick wall for frame, 58mm x 68mm x 2.4mm thick wall for glass sash With 5mm clear float glass (WINSTA KOMMERLING/ FINESTA/ ENCRAFT)

Providing and fixing in position collapsible M.S. shutters with vertical channels 20mmx10mmx2mm braced with flat iron diagonals 20mmx5mm size with top and bottom rails of T-iron 40mmx40mmx6mm with 38mm dia steel pulleys complete with bolts and nuts, locking arrangements, stoppers, handles including applying a priming coat of red lead paint.

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).

DOOR WINDOW SS FITTINGS Supplying, fitting, fixing Stainless Steel fittings of approved make, resonably smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary c.p. brass screws etc. complete.( bright natural matt & satin finished ) a. Sliding Door Bolt ii) 250mm x 16mm

b. Tower Bolt ii) 250mm x 10mm

c. Door Handle 150mm

ALUMINIUM FITTINGS Supplying, fitting, fixing anodised aluminium fittings of approved make, resonably smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary aluminium screws etc. complete.( anodised to bright natural matt & satin finished ) i) Door stopper with rubber stopper

l) Hydraulic door closure

m) Mortice lock vertical type iii) 100mm(Godrej with handle (6 lever)

Providing wood work in frame (chowkhats) of doors, windows, clerestory windows and other similar works wrought, framed and fixed in position in contact with C.C. or brick masonry wall including supplying, fitting and fixing with M.S. hold fast (40mm x 3mm x 250mm) as per design embeded in cement concrete block in proportion 1:2:4 and with two coats of kiricide oiling to the timber faces in contact with C.C. and masonry as directed and specified. (a) With sal wood All Floor

Providing, fitting and fixing fully glazed window with sash bars including oxidised M.S butt hinges (75mmx 60mmx3.15mm) 2nos.on each leaf and 3 nos. on single leaf (glass panes to be measured and paid separately) A) With Teak wood / Sissu wood. (iii) 30mm thick

Providing and fixing flush door shutters solid core construction with frame of 1st class hard wood with cross band and face veneered ply wood face panels conforming to relevent I.S code including oxidised iron butt hinges (100mm x 75mm x 3.5mm) 6 nos with necessary wood screws. a) Decorative type face panel and block board core. (i) 35 mm thick .

(ii) 25 mm thick .

Providing and fixing flush door shutters solid core construction with frame of 1st class hard wood with cross band and face veneered ply wood face panels conforming to relevent I.S code including oxidised iron butt hinges (100mm x 75mm x 3.5mm) 6 nos with necessary wood screws. a) Non Decorative type face panel and block board core. (i) 35 mm thick .

(ii) 30 mm thick .

(iii) 25 mm thick .

Providing, fitting and fixing factory made wooden panelled doors with panel inserts of 75mm to 50mm width and 12mm to 20mm thickness,joined together with continous tongue and groove joints glued together with Movicol or other approved adhesive leaving a vertical groove of 7.5mm to 15mm between the inserts,the edges of panel inserts being feather tongue into styles and rails including providing three pairs of oxidised M.S butt hinges (100mm x75 mm x3.55mm) and furnishing with moulded timber beading of size 25mmx15mm around the panels complete as per drawing (moulded timber bead and all fittings except hinges to be paid separately) (ii) 35 mm thick with panel inserts of 20mm thickness.

WIRE GAUGE SHUTTERS Providing, fitting and fixing Wire Gauge shutters using galvd. M.S. wire of I.S. designation 85G with wire of dia 0.56 mm for doors, windows and clerestory windows including oxidised M.S. butt hinges (100mm x 58mm x 1.90mm). A) With Teak wood / Sissu wood. 35 mm thick.

30 mm thick .

B) With Gamari/ Bonsum/ Sundi wood. 35 mm thick.

30 mm thick .

C) With 1st class local wood(Hollock) 35 mm thick.

30 mm thick .

Extra for providing lapping with 1st class Teak wood battens of 25mm minimum depth on all edges of the shutters.

Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured) : Rectangular or square

FRP FRAME providing & fixing of factory made Fibreglass Reinforced Plastic (FRP) door frame of FIBREWAYS having three legged of cross section 90mmx45mm having single rebet of 32 mmx15mm to receive shutter of 30 mm thickness .The laminate door frame moulded with fire retardant grade unsaturated polyster resin and chopped mat .Door frame laminate and shall be filled with suitable wooden block in all the three legs the frame shall be covered with covered glass from all sides. MS stay shall be provided at the bottom to steady the frame.

FRP FLUSH DOOR Supplying & fixing of factory made 30mm thick Fibreglass Reinforced Plastic (FRP) panneled door shutter of required colour of FIBREWAYS made with fire retardant grade unsatured polyster resin,moulded to 3mm thick FRP laminate for forming hollow rails and styles,with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings,cast monolithically with 5mm thick FRP laminate for panels and conforming to IS:14856-2000 including fixing to frames complete as per direction of Engineer-in charge.

Providing, fitting and fixing M.S. grill of required pattern for windows/ clerestory windows/ opening with M.S. Flats at required spacing in frame all round, square or round M.S. bars with round headed bolts and nuts or screws. I. Plain grill (b) Fixed to steel frames

(c) Fixed to Brickwork/P.C.C/R.C.C.

Providing and fixing 1.25 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using M.S. angels 40x40x6 mm for diagonal braces

Providing and fixing rolling shutters of approved make made of 80mm wide M.S. laths interlocked together through their entire length and jointed together at the ends by end-locks mounted on specially designed pipe shaft with bracket plates, guide channels and arrangements for inside and outside locking with push-pull operation complete including cost of wire, spring and hood cover for the shutters.

Supplying, fitting and fixing door frame made of M.S. equal angle of size 40mmx40mmx5mm fabricated, welded, mitred and joined as per relevant I.S. Codes including fitting 8 nos. of M.S. hold fast, providing closing/ holding device for 2 nos. tower bolts of door for each side and 1 no. for fitting and fixing Aldrop (for single leaf) to the frame for fixing the door to the frame, applying primer to all steel surfaces fixing the frame to the wall/ R.C.C. members by embedding the hold fast securely in C.C. block of M-15 grade complete at all levels as specified and directed. (Door hinges to be paid as per relevant item of the schedule of rates).

Providing, fitting and fixing powder coated pressed steel door frame made of 1.25mm/ 1.6mm thick sheet of various sizes with necessary hinge jamb, lock jamb, head and steel base ties at the bottom of the frame. The whole frame shall be welded or rigidly fixed together by mechanical means with base ties of pressed mild steel angle of size 20x20x1.25mm thick. Frame to be filled up with 1:4:8 P.C.C. after fitting the frame with brick/ concrete works etc.complete as directed by the department for all levels. (P.C.C. to be measured and paid for seperately). (a) 1.25mm thick sheet (i) Size 90mm x 60mm (Single rebate)

(iii) Size 125mm x 60mm (Single rebate)

(iv) Size 125mm x 60mm (Double rebate)

a) In beams and joists with connecting plates/ angled cleat.

b) In trusses and trussed purlins up to 25m span and 15.0m overall height.

Supplying, fitting and fixing double leaf heavy duty iron gate, frame made from 50mm x 6mm M.S. flat iron with another horizontal flat at the middle, 20mm dia M.S bars at 200mm apart from bottom flat to top flat and 20 mm dia M.S. bars at 200mm apart from bottom flat to middle flat including drilling, welding etc. complete. All vertical bars are to be protruded at least 100mm above the middle and top flat is to be flattended and pointed as directed. Necessary locking arrangement on both faces, arrangement for temporary closing the gate and 2 nos.( minium) strong iron hinges of M.S bars and flat of same sizes on each leaf to be embeded in C.C brick pillars as necessary including a red oxide painting to all iron works as directed and specified. (Separate payment will be made for posts).

Providing rails for plying of rollers of gate made made from 50mm x 6mm size M.S. flat and to be fitted with 3 nos of hinged hold fasts to be embedded in concrete prop. 1:2:4 of 10mm wide and 75 mm deep over brick flat soling 250mm wide including curing etc. complete.

Providing roller to the gate including welding etc.complete a) With 25mmx50mm (dia) roller

Providing fitting, hoisting and fixing of roof trusses including purlins fabricated using MS circular hollow section conforming to relevant I.S. code, as per approved design and drawings including providing M.S. cleats, base plates, bolts and nuts and one coat of red oxide Zinc Chromate primer and two coats of approved enamel paints complete including fitting necessary cleats etc. for fixing ceiling joists as per design and drawing as directed. a) TATA make Circular Hollow section- CHS of Grade YST-310 conforming to I.S. Specification : 1161-1998

Providing and fixing clear sheet glass beded in putty and fixed with/without wooden bidding including necessary cutting and glass to be required sized(payment for wooden bead shall be made separately) (3). Area of glass panes exceeding 0.52m2. (a). 5.00mm thick.

ALUMINIUM/STRUCTURAL GLAZING Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). for ACP & STRUCTURAL GLAZING WORK

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including: a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)- cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including: b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers. c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment , including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass. d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight. e) Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-in-charge. The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight structural glazing having all the performance characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineerin-Charge. Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be paid for separately under relevant items under this subhead. However, for the purpose of payment, only the actual area of structural glazing (including width of grooves ) on the external face shall be measured in sqm. up to two decimal places. Note:-2. The following performance test are to be conducted on structural glazing system if area of structural glazing exceeds 2500 Sqm from the certified laboratories accreditated by NABL(National Accreditation Board for Testing and Calibration Laboratories), Department of Science & Technologies, India. Cost of testing is payable separately. The NIT approving authority will decide the necessity of testing on the basis of cost of the work, cost of the test and importance of the work. Performance Testing of Structural glazing system Tests to be conducted in the NBL Certified laboratories 1. Performance Laboratory Test for Air Leakage Test (-50pa to – 300pa) & (+50pa to +300pa) as per ASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr” 2. Static Water Penetration Test. (50pa to 1500pa) as per ASTME- 331- 09 testing method for a range up to 2000 ml.”3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing method for a range upto 2000 ml” 4. Structural Performance Deflection and deformation by static air pressure test (1.5 times desing wind pressure without any failure) as per ASTME- 330-10 testing method for a range upto 50 mm” 5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing method for Qualitative test” Tests to be conducted on site 6. Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto 2000ml”

Providing, assembling and supplying visionglass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.26.2) For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. (i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.

Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineerin- Charge.

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building, for all heights and all levels etc. including: a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Compositem Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.

S.S. & M.S WORK Providing and fixing Stainless Steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i.e. fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer in-charge. (For payment, only weight of Stainless Steel member is to be considered. No extra payment for fixing accessories such as nuts, bolts, fasteners etc. will be considered)

PLASTER & PAINTING WORK 15 mm thick Cement plaster in single coat on single or half brick wall for exterior plastering GF to top floor level including arises, rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. External plaster A) On rough side b) In cement mortar 1:4 Upto plinth lvl

d) In cement mortar 1:6 G.FL.

8th FL./TERRACE

15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. A) On rough side d) In cement mortar 1:6 Gr. Floor

1st Floor

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

8th Floor/ Terrace

10 mm thick Cement plaster in single coat on fair side of brick/concrete walls for interior plastering up to 1st floor level including arises or rounded angles not exceeding 80mm girth and finished even and smooth including curing complete as directed. c) In cement mortar 1:5 Gr. Floor

1st Floor

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

8th Floor/ Terrace

10 mm thick Cement plaster in single coat on fair side of brick/concrete walls for interior plastering up to 1st floor level including arises or rounded angles not exceeding 80mm girth and finished even and smooth including curing complete as directed. for plastering on celling and soffits of stairs a) In cement mortar 1:3 Gr. Floor

1st Floor

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

8th Floor/ Terrace

Extra over item no 6.2.1 to 6.2.3 for providing and mixing water proofing materials in cement mortar in prop as recommended by the manufacturer including curing complete as directed. ii) 15 mm thick plaster d) In cement mortar 1:6

15 mm thick plain cement mortar bands in cement mortar 1:4 in width including curing complete as directed. c) Raised band

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections

WALL PAINTING Wall painting (two coats) with acrylic emulsion paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J&N paint/ Narolac) on new surface to give an even shade after throughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth. (a) Acrylic Emulsion Paint approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J&N paint/ Narolac).

Providing and applying Spectrum aggragate textured wall coating in the branded name of SPECTRUM with its all tools, plants and machineries and scaffolding etc. as per manufacturers guideline and specification of the product. r) Spectrum Rustik ( fine )

a) Applying one coat of cement primer of approved brand and manufacture on new wall surface after throughly brooming the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth.

b) Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on new wall surface (two coats) to give an even shade after throughly brooming the surfaces to remove all dirt and remains of loose powdered materials.

Wall painting (two coats) with acrylic emulsion paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J&N paint/ Narolac) on new surface to give an even shade after throughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth. (a) Acrylic Emulsion Paint approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J&N paint/ Narolac).

Wall painting (two coats) with Plastic emulsion paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) on new surface to give an even shade after throughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth. (a).Plastic Emulsion Paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac)

Finishing old/ new wall with water proofing weather coat smooth anti-fungal exterior painting of Apex brand of Asian Paints and of required shade after cleaning and clearing the surface etc. including scaffolding complete as directed at all levels (two coats)

Providing two coats of Birla White Wall Care Putty (Water Resistance White Cement based putty for concrete/ mortar walls and ceiling both internal and external) after removing all loosely adhering material from the wall surface with the help of emery stone, putty blade or wire brush and moistening the wall with sufficient quantity of clean water as specified and directed by the department. (Total thickness of two coats is maximum 1.5mm). (i) Thickness = 1.5 mm thick

Painting two coats (Including priming coat) on new steel and metal surface surface with enamel paint of approved brand and manufactures (Asian paint/ Berger paint/ ICI paint/ J&N paint/ Narolac) to give an even shade including cleaning the surfaces of all dirt, dust and other foreign matter. (i).Surfaces over 100mm in width or girth. b). High gloss (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac).

Polishing with french sprit polishing on new wood and wood based surfaces to give an even surface including cleaning the surface of all dirt, dust sand papered smooth and including a coat of wood filter.

FLOORING WORK Providing Antiskid Tiles of approved quality size, shape not less than 8mm on floor, skirting over a cement mortar bed 15mm thick of 1:3 (1 cement: 3 coarse sand) approved make fix with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)/ white cement complete at all level as specified and directed. (A) CERAMIC i)Normal range (Sizes 300 mm x 300mm and above) (a)Orient made: Galaxy Brown, Galaxy creama, Galaxy Pink, Galaxy Green, Pulsar Beige, Pulsar Blue, Pulsar Dove, Pulsar Pink, Burj Brown, Burj Green, Burj Slate

iii)Executive range-2 (Sizes 600 mm x 600mm and above) Somany made- VC Shield (Group- 25) (605x605) mm a) Deluxe -VC

Providing polished ceramic wall tiles of approved quality, size, shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey / Sika / Pedelite / Rouf) /white cement slurry mixed with approved pigment to match shade of tiles complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department). (Walls means both interior and exterior walls). b) Executive range Somany/ Orient/Nitco/Asian Make ii) Of size 250mmx350mm and above

Providing Antiskid Tiles of approved quality size, shape not less than 8mm on floor, skirting over a cement mortar bed 15mm thick of 1:3 (1 cement: 3 coarse sand) approved make fix with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)/ white cement complete at all level as specified and directed. i)Normal range (Sizes 300 mm x 300mm and above) Somany made- Durastone (Unpolished heavy duty Vitrified Tiles) b)Deluxe

Providing VITRIFIED floor tiles of approved quality of specified size, shape and thickness not less than 18mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department) a) Normal range Somany/ Orient/Nitco /Varmora/VITA/ Marbito/ Make ii) Of size 600mmx600mm and above

b) Executive range (800mmx800mm) Somany/Varmora/Nitco/Orient made

c) Delux range Somany/ Orient/Nitco /Varmora/VITA/ Marbito/ Make i) Of size 1000mmx1000mm and above

Providing polished vitrified wall tiles of approved quality, size, shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)/white cement slurry mixed with approved pigment to match shade of tilesc complete at all levels as specified and directed. (coloured pigment should be in conformity with colour of tiles and as approved and directed by the department). iii) Of size300mmx600mm and above

Providing 18mm thick Granite slab on vertical face of pedestal laid over 10 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete as directed with approved quality of shade.

40 mm thick cement concrete floor consisting of 25 mm under layer of cement concrete in prop. 1:3:6 (1cement : 3 coarse sand : 6 coarse aggregate of 12.5 mm and down) and 15 mm thick wearing layer in cement concrete in prop. 1:1:2 (1cement :1 coarse sand : 2 coarse aggregate of size 10mm down) finished with a floating coat of neat cement finish using cement slurry for bond @ 2.75 kg. per square metre of floor area , wearing layer is to be laid in panels including curing etc. complete as directed.

Providing,fitting and fixing Laminated abrasion resistant wooden flooring from Uniproducts (India) Ltd.of thickness not less than 8.2mml laid on existing concrete floor with underlayer of approved transparent polythene and foam sheet to make the floor surface even and sound free complete as directed and specified Laminate Floorings- A from Uniproducts(India) Ltd. i) Unitex AC3 Brand

WOODEN FLOORING FOR STAGE & GAME AREA THE SURFACE BOARD: Made of kiln seasoned treated Teakwood finished with 21mm thick,57 to 83mm width and in random length in tongue and groove shape.The edges of the boards will have a finger lock groove and the bottom side with air passage over and treated with special anti–termite and water resistant lacquer.THEUNDERFRAME:-Made of pine wood runners of 70mm x45mm treated with anti–termite solution and fixed on the bottom side with10mm thick air–cushion pads by staple through the two wings at 350mm c/c THE INSTALLATION:-The IPSsub-floor to be treated with acrostic and a vapor barrier of 6mm thick to be placed on the leveled IPS sub–floor before lying the underframe.The runner shaving air–cushion pads to be placed on the vapor barrier in perfect level at 350mm c/c in one direction.The surfaceboards will be screwed to the runners through the tongue only and will lock the screwed tongue by the groove of the adjoining boards.The ends of the boards will be locked by inserting the wooden fingers through the edge grooves and fixed with suitable adhesive. An expansion gap of 8 to 10 mm will be left open between the wooden flooring and the surrounding tiled area or walls. THE FINISHING: After installation the floor will be machine sanded in uniform level and finished with P.U.polishing water based polyurethane lacquer Gameline marking to be carried out in required colors before applying the finish coat

Providing polished granite slab of approved quality, size, shape and thickness not less than 18 mm on floors, skirtings, treads and risers of steps over cement mortar bed 15 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile Choksey/Sika/Pedelite/Rouf) /white cement slurry mixed with approved pigment to match the shade of granite slab, complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of slab and as approved and directed by the Department). (iii) Deluxe Quality (ii) With White cement

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Granite of any colour and shadea rea of slab over 0.50 sqm

Providing edge moulding to 18 mm thick Granite stone, including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/Granite / stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Kota-stone slab flooring of 18 mm thick over 20mm thick base of cement plaster 1:6 (1 cement : 6 coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete. (1) 550mm x 550mm

Kota stone slab of 18 mm thick in riser of steps, skirting, dado and pillars laid with 10mm thick cement plaster 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs including rubbing and polishing complete. (1) 550mm x 550mm

Providing and laying 65mm thick C.C. floor with metallic concrete hardener topping under layer of 50 mm thick cement concrete 1:2:4 (1cement:2 coarse sand:4 coarse aggregate of 20 mm and down) and top layer of 15mm thick of metallic cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 stone aggregate 6 mm and down) by volume with which metallic hardening compound of approved quality is mixed in the ratio of 4:1 (4 parts of cement: 1 part of metallic floor hardening compound of approved quality by weight) including finishing with curing complete as directed.

40 mm thick cement concrete floor consisting of 25 mm under layer of cement concrete in prop. 1:3:6 (1cement : 3 coarse sand : 6 coarse aggregate of 12.5 mm and down) and 15 mm thick wearing layer in cement concrete in prop. 1:1:2 (1cement :1 coarse sand : 2 coarse aggregate of size 10mm down) finished with a floating coat of neat cement finish using cement slurry for bond @ 2.75 kg. per square metre of floor area , wearing layer is to be laid in panels including curing etc. complete as directed. 40 mm thick

Cement plaster skirting with cement mortar in prop. 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement including rounding of junctions with floor. (b) 20 mm thick

Providing and fixing glass strips in joints of cement concrete flooring /Terrazo flooring in all level (b) 40 mm wide (i) 4 mm thick

Providing and laying tactile tile/Pavit tile (for vision impaired persons as per standards) of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.

FALSE CEILLING & WATER PROOFING WORK Providing and fixing GI Clip in Metal Ceiling System of 600x600 mm module which includes providing and fixing ‘C’ wall angle of size 20x30x20 mm made of 0.5 mm thick pre painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main C carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of GI steel 0.45 mm thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm centers with help of suspension brackets. Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive), fixing with clip in tiles into spring ‘T’ with GI Metal Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and 0.5 mm thick with 25 mm height, made of G I sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation

Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture spintone/ cosmos / Hexa or equivalent of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture (Spintone / Cosmos/hexa) in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceilingusing G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by engineer-in-charge. Note :- Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames/opening (cut outs) having area less than 0.30 sqm.The calcium silicate ceiling tile shall have NRC value of 0.50 (Minimum), light reflection > 85%, noncombustible as per B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity <0.043 w/m 0 KC.

Supplying, fitting, fixing and painting where necessary (one coat primer and two coats of paint) M/F Suspended Ceiling which includes G.I. perimeter channels of size 0.55mm thick (having one flange of 20mm and another flange of 30mm and a web of 27mm) along with perimeter of ceiling, screw fixed to brick wall/ partition with the help of nylon sleeves and screws, at 610mm c/c. Then suspending G.I. intermediate channels of size 45mm (0.9mm thick with two equal flanges of 15mm each) from the soffit at 1220mm c/c with ceiling angle of width 25mmx10mmx0.55mm thick fixed to soffit with G.I.cleat and steel expansion fasteners. Ceiling section of 0.55mm thickness having knurled web of 51.5mm and two equal flanges of 26mm each with lips of 10.5mm are then fixed to the intermediate channel with the help of connecting clip and in direction perpendicular to the intermediate channel at 457mm c/c, 9.5mm/ 12.5mm tapered edge Gypboard (conforming to IS:2095-1982) is then screw fixed to ceiling section with 25mm long drywall screws at 230mm c/c. Screw fixing is done mechanically either with screw driver or drilling machine with suitable attachment. Finally, the boards are to be jointed and finished so as to have a flush look which includes filling and finishing the tapered and square edges of the boards with jointing compound, joint paper tape and two coats of drywall topcoat suitable for Gypboard complete at all levels as specified and directed. (For light fittings, providing opening for doors, window, ventilators etc, cut out made with frame of perimeter channel supported suitably to be measured and paid separately where necessary). 12.5mm thick

Supplying, providing, mixing and laying over waterproofing layers/ coatings with concrete screed of average 30mm thick or as per drawings/ requirements in proportion 1:2:4 (1cement : 2fine aggregate : 4coarse aggregate) (by volume) with 10mm and down well graded aggregates and admixed with a normal plasticizer like Master Plast PL-1 of Choksey Chemicals /Dr. Sealkit Normal Plast (Asian Chemicals)/Rheomac 707 of BASF @ 0.3% by weight of cement and thereafter scoring the top surface of the concrete screed @ 200mm c/c as specified and directed by the Department.

Providing, supplying, mixing and champhering the edges along joint of wall/ parapet wall and raft/ roof slab having champhered dimension of 150mm x 150mm with cement sand mortar (prop.1:4) mixed with Master Proof IWP-1 of Choksey Chemicals /Dr. Sealkit No. 1 of (Asian Chemicals)/ RHEOMAC 707 of BASF@ 0.2% by weight of cement over a primer coat on the area to be champhered with a combination of 100% acrylic Polymer Master Crete M-81/Dr. Sealkit Sealcrete (Asian Chemicals)/ RHEOMAC 115 of BASF of Choksey Chemicals and cement in the ratio 1:2 to be applied by brush as specified & directed by the Department complete.

(A) Providing and applying over roof slab/ raft slab, polymer modified bituminous waterproofing membrane Proofex SM of Fosroc chemicals on an unprimed substrate using specially designed spray application equipment to be applied in a single coat, using wet on wet passes to give a nominal dry film thickness of 2mm followed by applying ProofexGeo Textile having weight of 200gm per sq.m immediately after the application of Proofex SM membrane when the surface is still wet but not tacky and as specified and directed by the Department.

Applying one coat of epoxy coating Techoxy of Choksey Chemicals followed by two coats of Polyurethane waterproof coating Techcoat 61P at an interval of 12hours each for waterproofing of external walls, roofs, terraces, chajjas, etc. as specified & directed by the Department complete.

EXTRA ITEMS Providing plinth protection 50mm thick to cement concrete 1 : 3 : 6 with coarse agg.of 20mm nominal size including finishing the surface with 10mm thick cement plaster in proportion 1:3 with a floting coat of neat cement finished.

Providing Drain with brick work in cement mortar in proportion 1:5 with half brick thick side and 100mm thick C.C. (1:3:6) base over one brick flat soling including 15 mm thick cement plastering in prop. 1:3 finished with a floating coat of cement slurry as directed with necessary shuttering for sides and earth work in excavation of foundation trenches and refilling the sides after completion of the work etc. as specified. i). 300mm wide and average 150mm deep with bed slope 1 in 150 with initial depth of 100mm.

Providing and fixing Duraboard HD-100 premoulded compressible filler board at all heights and depths of minimum density 95kg/cum, non-staining having less than 1% water absorption, compression recovery of 93% (minimum) as per manufactured specification with polysulphide sealant to seal the expansion joint including preparation of surface, Polymer Modified Mortar (PMM) (Proportion 1cement: 3 sand:1 acrylic polymer) nozing, carriage of materials, cutting and placing to the required size complete at all levels as per drawings and direction of Engineer-in-Charge. (e ) 75mm wide

Providing and fixing sheet covering over expansion joints with iron screws as per design. Aluminium fluted strips 3.15 mm thick. 200 mm wide

Supply and Installation of polycarbonate multi-layered system, a complete assembly of extruded multilayer UV protected polycarbonate panels incorporated into a complete system. Coextruded UV protected polycarbonate panel system of min 18 mm thick panel of 1050-1200 mm width for bigger spans and minimal junctions for better performance. Panels shall have minimum seven layers with all fixing accessories to ensure best performance for wind uplift, vibration, oil canning and visual appearance. Panels shall be manufactured with vertical offset standing seam at both sides of the panel. Panels shall provide angular daylight for better shading and variable day light transmission throughout the day with translucent and opaque combination of layers. Panels have to be fixed on Purlin with snap on connectors with grip lock locking mechanism and will be secured on MS structure (will be paid Separately) with 3 numbers self-drilling screws & trapezoid SS fasteners holding the base of the standing seam offering best stability having a pull-out load of min. 7000N (7KN) tested as per ISO 6892:1998 and IS 1608: 2005. Panels must satisfy Dart drop impact test as per IS 14443-97 shall show no sign of breakage on Polycarbonate Panel which have been exposed to UV for a min. of 500 Hours as per ASTM G 155. Panels shall not have Yellowness Index as per ASTM D 1925 of 15 units when tested on a sample exposed to UV for 500 Hours as per ASTM G 155. U value shall not be more than 1.8 W/m2K as per EN ISO 10077-2:2018. Panel shall be with additional End cap/Aluminium U/F profile/ Glazing Bar for ends as required. Panel shall be fixed over MS structural steel/MS purlin (paid separately) conforming to the detail technical specifications as per approved architectural drawings. Trained and factory authorized labour with supervision to complete the entire panel installation as per drawing & direction of the engineering in charge. Color: As per Approval. Approved Make: DPI Daylighting/ Bayer/ Polygal/ GE/ Vergola or Equivalent.

Antistatic flooring in ICU Supply &amp; fixing flexible Medintech plus /simpurity range pvc sheet flooring in 2 mm thickness in the size of 2 mtr X 20 mtr use area classification 23/34/43 results from independent testing demonstrate that product inherently inhibits the growth of microbial strain MRSA. It shall be homogeneous in construction. The flooring shall incorporated a specially (PUR) to give polish free maintenance imported pvc vinyl flooring with total weight 28oo g/m2,dimensional stability EN-434, static electrical charge &lt;2kv, impact sound reduction approx ISO 717-2, good resistant to scratch,slip,fire ,chemical &amp; does not favor in growth fungi &amp; bacteria Make –Armstrong

For OT ESD- Supply & fixing of flexible Royal esd range PVC sheet flooring in 2 mm thickness in the size of 1.83 X 25 mtr homogeneous with conductive backing polyvinylchloride marbled,impact sound reduction ISO-140-8,total weight 3200 g/m2,static electrical charge<2kv,electrical insulation to ground>50,good resistant to scratch,slip,fire ,chemical & does not favor in growth fungi & bacteria Make Armstrong

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Providing & fixing M.R.I. Led sheet as per specification and direction of engineer in charge.

Double Skin Modular Clean Room Wall Panels composite system 80 mm thk made up of sheet thk 0.8 mm GPSP/ FS sheets ( TATA make) epoxy polyester Powder Coated (NLT 60 micron) GPSP (Galvanised Plan Skin Pass zero Spangle ) sheets on both side with puff having density 40kg/m3 as infill with GI Profile for reinforcement along the periphery an floor track to accommodate the Epoxy floor coving Flush with the wall panel with relevant fittings and material required, Cut out for electrical board ,Magnehaulic guage etc. . All Joints will be completely sealed with clean room compatible silicon

Providing and fixing Sio Crush Rail (PVC) SIO CRS 138 D or equivalent 138mm Wall Proctection ,extends 3" (76 mm) from wall and Mounted on a sturdy .080" (2mm) thick, Continuous aluminum retainer , .080" (2mm) thick, scratch and stain resistant rigid vinyl cover, mounting fasteners are included with Each order available in standard colors, several pattern and finish options, as well as custom colors - Manufactured with woodland pattern full wrap of specification and as per design and drawings complete.

Providing and fixing Sio wall guard (PVC) SIO WG 150 D or equivalent 150mm Wall Proctection ,extends 21mm from wall and wall Mounted on a sturdy .080" (2mm) thick, Continuous aluminum retainer , .080" (2mm) thick, scratch and stain resistant rigid vinyl cover, mounting fasteners are included with Each order available in standard colors, several pattern and finish options, as well as custom colors - Manufactured with woodland pattern full wrap of specification and as per design and drawings complete.

Providing and fixing Sio Corner Guard (PVC) SIO CGP 52 S or equivalent 52 X 52 mm with 90° Corner Proctection , Mounted on a sturdy .070" (1.8mm) pre-slotted continuous aluminum container and (2mm) thick scratch and stain resistant rigid vinyl cover, Manufactured 4' to 6' standard heights as per drg and specification, custom heights available, All mounting fasteners and top and bottom caps are included with Each order ,Available in standard colors and Woodland patterns, of specification and as per design and drawings complete.

Stair Case Doors’ Specification of Fire Doors for Wall Opening 2000x2100mm: Providing Fire Resistant Door Frame made up of Galvanised Steel having Double Rebate Section 143x57 mm with Mitered Joint & Door Leaf shall be 46 mm Thick (D/L Equal) Shutters made up of Galvanized Steel having 2 Nos. Vision Panels made up of 6mm Thick Fire Rated Glass of Size 300x300 mm with fire rated Gasket, Infill Material Honeycomb Core, RAL Colour Painted Finish, Handing TBC, Fire Rating: 2 Hr. along with following Hardware: a) Ball Bearing Butt Hinge b) Door Closer with Standard Arm Silver Finish c) Single Point Surface Panic Latch d) External Lever Handle with locking arrangement e) Panic Strike Plate

Doors : Providing and Fixing fixing of sound reducing doors with 38db Noise reduction property as per the specification- Supply & installation of teak wood door frame of section 100x75 mm with one coat of anti-termite. Door shutter consisting of 77mm thick door shutter having 38 db acosutic rating having in fill of 50mm thk resin bonded glass wool of 24 kg/cum density with FR acrylic sealant sandwitch between two 9 mm thk (starpan or approved equiv. make ) calcium silicate board having density 1150kg/um and thermal condutivity 0.14 w/m k faced with 3.4 mm thk commercil ply 1mm thk laminate on both sides with heat activated instumescent fire seal strip of size 10mmx4mm mounted in the grooves having hardwood loping. including marshall acouctic seals around the jamb and head on frame rebates, which is adjustable to seal for noise, light and smoke for maximum gap of 8mm between frame and shutter. Along with all the Hardware & accessories like Heavy duty door closer, Panic bar, Dead lock, Hinges, Handle, Vision panel etc.

Supplying, fitting and fixing SoundSoak NSS Cord (FSS Cord) wrapped acoustical wall panel system of Anutone Acoustics Ltd. Including all fixtures and fittings. b) 25 MM

ALUMINIUM STANDING SEAM SINGLE SKIN ROOFING SYSTEM Providing and fixing of KALZIP 65/400 SelfSupported SecretFix STANDINGSEAM ROOFING SYSTEM in 0.9 mm thick in AA-3004 Aluminium Alloy including accessories. TopLayer- Kalzip Aluminum Profile Standing Seam 65 mm rib height and 400 mm width of STRAIGHT/TAPPERED profiled panel as per the Roof Geometry, manufactured from Kalzip Aluminum Alloy AA3004 as specified in BSEN1396:2007, minimum material thickness of 0.9 mm with PVDF2 finish. The material properties shall be as follows: Ultimate tensile strength: minimum 200N/mm2, 0.2% Proof Stress: min 185N/mm2, Modulus ofelasticity:70,000N/mm2. Sheets are to be laid in Single Length to meet there quirements of the building geometry and fixed on Aluminum Clip which is fixed to the top hat with SS-304 screws.

Flashing - Flashings manufactured from aluminium alloy AA 3004 (AlMn1Mg1) as specified in BS EN 1396: 2007 minimum material thickness of 0.9 mm and Fluorocarbon PVDF finish on the exposed surface. The material shall be of the same colour. Girth – 400mm to 600mm

Providing, fitting, hoisting and fixing of roof trusses fabricated using any one or combination of following sections of (i) Square (ii) Rectangular Hollow section of specification SHS/RHS and including purlins, bottom runners and providing M.S. cleat, M.S. angle base plank, bolts and nuts with red oxide primer including fitting bottom runner and cleat etc. for fixing ceiling joist as per design complete as directed as per specifications. a) Using TATA make RHS/SHS of Grade 310 conforming to relevant I.S. code 4923 : 1997

ROAD WORK Construction of Sub-grade and earthen shoulders with approved materials obtained from borrow pits, with all lifts & leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2 (including compensation of earth ). (Including cost of testing of materials at site and laboratory as directed by the deptt.) b) from Government land

Construction of Granular sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per Clause 401 of MoRTH specifications (with an initial lead of 5 km) (including cost of testing of materials at site and laboratory as directed by the deptt.) (a)Using Grading I material

(b)Using Grading II material

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., and removal of the same for in-situ reinforced concrete and plain concrete work in R.C.C. approach road. (a) Using 38mm thick plank

Providing and laying design mix cement concrete of M-30 grade, in roads/ taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber, finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction / expansion, construction & longitudinal joints (10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineer-incharge (Item of joint fillers, sealants, dowel bars with sleeve/ tie bars to be paid separately). Note:- Cement content considered in M-30 is @ 340 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable separately. Cement concrete prepared with batch mixing machine

Providing and fixing in position pre-moulded joint filler in expansion joints.

Providing and laying in position bitumen hot sealing compound for expansion joints etc. Using grade 'A' sealing compound.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Providing and laying of inter locking concrete block pavement (ICBP) with cement concrete paver blocks as per IS 15658-2006 of thickness 80mm and 28 days compressive strength not less than 40 N/m over a layer of bedding sand of compacted thickness 30mm, laid either in stretcher/ running/ herringbone pattern of bonds as directed by the engineer and in proper level and grade and compacted with appropriate equipment such as plat vibrator along with spreading of a thin layer of joint filling sand to fill up the gaps between blocks including construction of edge restraint wherever required complete as per drawings and Technical specification clause 1504 of MORD.

Painting runway/taxi track/apron marking with adequate nos of coats to give uniform finish with road marking paint of superior make as approved by the Engineer-incharge, i/c cleaning the surface of ail dirt, scales, oil, grease and other foreign mater;al etc. and lining out complete. New work (Two or more coats)

Providing and fixing 150 mm dia UPVC pipe for rain water spout upto 300 mm length.

Manufacturing, supplying and fixing retro reflective sign boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bi-lingual), symbols and borders etc. as per IRC ; 67:2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM-D- 4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. angle iron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 Nos. M.S. angles of size 35x35x5 mm to a vertical post made up to M.S. Tee section ISMT 50x50x6 mm welded with base plate of size 100x100x5 mm at the bottom end and including making holes in pipes, angles flats, providing & fixing M.S. message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical MS-Tee support to be painted in black and white colours). Back side of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts etc. complete as per drawing, specification and direction of Engineer--in-charge. Mandatory/ Regulatory sign boards of 900 mm diametre with support length of 3750 mm

Cautionary /warning sign boards of equilateral triangular shape having each side of 900 mm with support length of 3650 mm

P/F of radium signage for direction and other signage

HORTICULTURE & LANDSCAPING Providing and fixing M. S. tree guard 50 cm square in plan, height 1.40 metre above ground level and 0.50 metre below ground level. The vertical members shall consist of four nos of angle iron of size 25x25x5 mm 1.9 long, one at each corner and 8 nos flat iron of size 25x5 mm 1.4 long. The vertical members shall be welded to 4 nos 25x6 mm M. S. flats placed horizontally around the vertical member of the cage. One name plate of 1 mm thick M.S. sheet of size 250x100 mm shall be welded to the tree guard near the middle height and lettered CPWD / PWD/ any other approved name. The tree guard shall be fixed to the ground by making suitable holes and by embedding four corners leg in the ground, including refilling the earth, compaction etc. complete. The tree guard shall be painted with two coats of paint of approved brand and manufacture over a coat of primer, complete in all respect.

Providing & laying RCC bench

Electrical Lawn mover power Grass cutter & power weed shear

Supplying and installation of Field Turf Turket PVC sports surface (vinyl sports floor covering) over fibreglass mat with PVC foam backing including anti bacterial coating and protected with dirt resistant treatment for ease of maintenance complete as specified and directed. (A) F-25 (filament ht. 25mm)

Supplying and planting of terrestrial orchids with required size of pot including filling the pot to the top surface with appropriate soil media made of garden soil, river sand, cow-dung, leaf mould, fertilizer, pesticides as per specification and necessary maintenance for a period of 4 months from the date of planting complete as specified and directed . (Mixing of different ingredients of soil media to be made in presence of Deptt. official / Specialist concerned) (A) With Aeirides (I) Using earthen pot of 30 cm dia.

(III) Using concrete pot of 60 cm dia.

(B) With Dendrobium (Hybrid) (I) Using earthen pot of 30 cm dia.

(III) Using concrete pot of 60 cm dia.

(C) With Mokara (I) Using earthen pot of 30 cm dia.

(III) Using concrete pot of 60 cm dia.

(D) With Vanda (hybrid) (I) Using earthen pot of 30 cm dia.

(III) Using concrete pot of 60 cm dia.

Supplying and planting of house plants in required size of pot including filling the pot to the top surface with appropriate soil media of garden soil, river sand, cow-dung, leaf mould, fertilizer, pesticides as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed . (Mixing of different ingredients of soil media to be made in presence of Deptt. official / Specialist concerned) (A) With Fancy leaf caladium/Coleus (i) Using earthen pot of 30 cm dia.

(iii) Using concrete pot of 60 cm dia.

(B) With Indian rubber plant / Prayer plant (i) Using earthen pot of 30 cm dia.

(iii) Using concrete pot of 60 cm dia.

(C) With Fragrant dracaena / Silver net leaf / Philodendron / Devil's back bone /Peperomea/Croton (i) Using earthen pot of 30 cm dia.

(iii) Using concrete pot of 60 cm dia.

(D) With Peacock/spider/Umbrella (i) Using earthen pot of 30 cm dia.

(iii) Using concrete pot of 60 cm dia.

(E) With Maiden hair fern/Aloe/Boston fern/Swiss cheese plant/Forget me not (i) Using earthen pot of 30 cm dia.

(iii) Using concrete pot of 60 cm dia.

(F) With Marry Christmas begonia / Polypodium / Aluminium plant (I) Using earthen pot of 30 cm dia.

(III) Using concrete pot of 60 cm dia.

(G) With English Ivy (I) Using earthen pot of 30 cm dia.

(III) Using concrete pot of 60 cm dia.

(H) With Iron Cross Begonia (I) Using earthen pot of 30 cm dia.

(III) Using concrete pot of 60 cm dia.

Supplying and planting of palms with required size of pot including filling the pot to the top surface with appropriate soil media made of garden soil, river sand, cow-dung, leaf mould, fertilizer, pesticides as per specification and necessary maintenance for a period of 4 months from the date of planting complete as specified and directed . (Mixing of different ingredients of soil media to be made in presence of Deptt. official / Specialist concerned) (A) With Bottle palm (III) Using concrete pot of 60 cm dia.

(B) With Erica palm (Butterfly palm)/ Kentia palm (III) Using concrete pot of 60 cm dia.

(C) With Chinese Palm (III) Using concrete pot of 60 cm dia.

(D) With Fan Palm /Finger palm (III) Using concrete pot of 60 cm dia.

Supplying and planting of seasonal flower in required size of pot including filling the pot to the top surface with appropriate soil media made of garden soil, river sand, cow-dung, leaf mould, fertilizer, pesticides as per specification and necessary maintenance for a period of 4 months from the date of planting complete as specified and directed . (Mixing of different ingredients of soil media to be made in presence of Deptt. official / Specialist concerned) (I) Using earthen pot of 30 cm dia.

Supplying and planting of cactus in required size of pot including filling the pot to the top surface with appropriate soil media made of garden soil, sand, cow-dung, fertilizer, pesticides as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed . (Mixing of different ingredients of soil media to be made in presence of Deptt. official / Specialist concerned) (A) With Peanut Cactus / Rat tail Cactus (I) Using earthen pot of 30 cm dia.

(III) Using concrete pot of 60 cm dia.

(B) With Prickly pear (I) Using earthen pot of 30 cm dia.

(III) Using concrete pot of 60 cm dia.

(C) With Parodia globular (I) Using earthen pot of 30 cm dia.

(III) Using concrete pot of 60 cm dia.

Supplying and planting of Dahlia / Chrysanthemum / Gladiolus on the ground ( bed planting, bed size 45 cm x 45 cm x 45 cm) including the preparation of the soil, providing organic manure and fertilizer, pesticides as per specification and necessary maintenance for a period of 4 months from the date of planting complete as specified and directed .

(B) With Hybrid tea rose / Miniatune rose

HEDGE PLANTING / EXTERNAL HEDGE Supplying and planting of suitable plant materials for preparation protective / external hedge (50 cm wide) including the preparation of the ground by mixing organic manure and fertilizers as per specification and necessary maintenance for a period of one year from the date of planting complete as specified and directed . (A) ADOPTING SINGLE ROW PLANTING METHOD (i) With Duranta

(ii) With Kamini

(iii) With Chinese Bamboo

(iv) With Thuja / Ixora

TREE PLANTING Supplying and planting of ornamental trees (1'-0" height sapling) including pit making ( 60 cm x 60 cm x 60 cm ), filling the pit with appropriate soil media, manure and fertilizers as per specification and necessary maintenance for a period of one year from the date of planting complete as specified and directed . SHADE TREE (A) Neem / Mahaneem / Beef wood / Bakul / Acacia / Siris / Devils tree / Kadam / Palash / Pink Cassia / peepal / Silver oak / Simalu / Ajar

(B) Kanchan / Nahar / Arjunu

(C) Sonaru

(D) Bottle Brush / Nil Gulmohar / Debadaru / Weeping Willow

(E) Ravenala

(F) Paine

(G) Christmas tree / Kuki

Flowering Tree (A) Gulmohar / Ashok

(B) Kanchan

SHRUB PLANTING Supplying and planting of ornamental shrub ( below 1'-0" height ) including pit making ( 60 cm x 60 cm x 60 cm ), filling the pit with appropriate soil media, manure and fertilizers as per specification and necessary maintenance for a period of one year from the date of planting complete as specified and directed . (A) Radhachura / Krishnachura / Rat ki rani / Ixora / Jetuka

(B) Allmanda / Khorika zai / May flower / Kamini / Kathanda / Tecoma / Acalypha / Bougainvillea / Dracaena / Togor / Nilakantha / Mussaenda

(C) Korobi / Azalea

(D) Thuja

(E) Poinsettia / Forget me not

CATTLE CATCHER Supplying fitting and fixing M.S. cattle trap fabricated, welde, mitred and jointed as per relevant IS code with ISMB 250 joist spaced not more than 1800mm apart and ISA 65 x 65 x 6 spaced not more than 200mm apart and fixing the same over RCC member / Brick wall complete as specified and directed.

LEVELLING & DRESSING Surface dressing of ground including removing vegitation and/ or undulation of ground not exceeding 150mm deep and disposal of rubbish outside the periphery and lift up to 1800mm in all kinds of soil.

f).Cutting and clearing bushes consisting of plants and all sorts of bambooes including uprooting and removing as necessary and filling up the holes with earth,dressing,ramming etc. complete.

FOOT BALL GOAL POST

FOOT BALL GROUND LINE MARKING WITH 2” RUBBERIZED EPDM WHITE PATTI

PREPARATION OF SYNTHETIC VOLLEY BALL COURT (01 NO) Volleyball Court HPU Synthetic Acrylic Surface 8 Layer System 30 MTX16 MT

Asphalt/Bitumen Sub Base 8”Thickness 30 MTX16 MT

Chain link fencing 1.5” PIPE, 10 FEETHIGH 3018 SQF

Flood Lights with Pole

Volley Ball Pole

PREPARATION OF SYNTHETIC TENNIS COURT (01 NO) Tennis Court HPU Surface (Made in India) 8 Layer System 120 FT X 60 FT 7200 SQ FT

Asphalt/Bitumen Sub Base 8”Thickness 120 FT X 60 FT 7200 SQ FT

An open saucer drain at the lower end. Drain connection is only till the courts.If it needs to be connected to the main drain the same will have to bed one by the client or water flows to the ground.

Laying 18" retaining wall by keeping the top level straight. No painting on the edge wall only plaster will be done.

Chain Link fencing: 10 Ft High, 12 guage, 2" dia MS Pipes spaced 10 Ft apart on all fours ides of the court with one or two gates, the top & bottom of the chain link will have 1-1/2" dia pipes & the chain link will be of 10 gauge GI wire spaced2" apart.

Flood Lights with Pole

TENNIS POLE

TENNIS NET

PREPARATION OF SYNTHETIC BASKET BALL COURT (01 NO) Providing and Laying Asphal/Bitumen SubBase and HPU Synthetic Flooring for Basket ball court HPU Synthetic Acrylic Surface 5 Layer System 34 MT X 19 MT 6954 SQ.FT

Asphalt/Bitumen Sub Base 8”Thickness 6950 SQ FT

An open saucer drain at the lower end. Drain connection is only till the courts.If it needs to be connected to the main drain the same will have to bed one by the Client or water flows to the ground.

Laying 12" retaining wall by keeping the top level straight. No painting on the edge wall only plaster will be done.

Chain Link Fencing 10 Ft High, 12 guage, 2" dia MS Pipes spaced 10Ft apart on all four sides of the court with one or two gates, the top & bottom of the chain link will have 1-1/2" dia pipes & the chain link will be of 10 gauge GI wire spaced 2"apart

Basket ball Pole Fixed 2.2 MT EXTENSION, 20 MM FIBRE BOARD

INTERNAL PLUMBING WORKS SANITARY INSTALLATIONS & C.P FITTINGS Providing fitting and fixing vitreous water closet squatting pan (Indian type W.C Orissa pattern) with all fittings and fixtures complete including cutting and making good to the walls and floors whereever required. (Flushing Cistern to be paid separately) Indian type W.C Orissa pattern of size 580 x 440 mm/ Hindware make

Providing fitting and fixing vitreous china pedestal type water closet (European type W.C pan 400mm high ) with seat and lead ,CP brass hinges and rubber buffers , CI/MS brackets , 40 mm dia flush band with fittings including painting of fittings and brackets, required. (Flushing Cistern to be paid separately)(iv) Water closet POPULAR "S (Cat.No.20044) (inclusive of seat cover)/B) Hindware make

Providing fitting and fixing Vitreous china wall hang water closet (European type W.C pan 400mm high) with seat and lead ,CP brass hinges and rubber buffers , CI/MS brackets , 40 mm dia flush band with fittings including painting of fittings and brackets, required. (Flushing Cistern to be paid separately)(iv) Wall mounted Closet Const (inclusive of seat cover and fittings) (Cat. No. 20040) Hindware make

Supplying, fiting and fixing concealed cistern with all internal fittings with CI brackets including fitting and fixing standard size CP flush pipe, union clamps etc. compete as directed and specified (pipes will be measured separately) Concealed Cistern (Cat.No.CIB-WHT-31801011X) with Control Plate (CP) (Cat. No. CIS-CHR-31191510X)(C) Jaquar Make

Supplying, fiting and fixing PVC flushing cistern with all internal fittings with CI brackets including fitting and fixing standard size CP flush pipe, union clamps etc. compete as directed and specified (pipes will be measured separately) (i) Sleek+ PVC cistern/Hindware make

Providing vitreous China wash basin with CI/MS brackets, C.P brass chain with plug,PVC waste pipe including painting of fittings and brackets, cutting and making good the walls wherever required. (Pillar cock, stop cocks, waste coupling are to be paid separately) PEDESTAL BASIN (with pedestal)/(iii) Constellation " 5 (Cat. No.10032/11010)/Hindware Make

UNDER COUNTER BASIN/(a) White/(i) Lara (Cat. No.10095)/ Hindware Make

Semi rigid pipe 32 mm dia

40 mm dia

Providing fitting and fixing Decorative Mirror complete as directed and specified. (A) Parryware Make /(b) Size 600mm x 450mm

Providing fitting & fixing stainless steel kitchen sink of Parryware make with CI/MS brackets, C.P. brass chain with rubber plug, PVC waste pipe etc. complete including painting the fittings ,cutting &making good the walls wherever required. (Sink cock, stop cocks, waste coupling are to be paid separately (A) Parryware Make/(iii) Single Bowl with Drain Board (360 x 180) Flat Edge - Glossy (Cat.No.C8536)

Providing fitting & fixing laboratory sink of Parryware make with CI/MS brackets, C.P. brass chain with rubber plug, PVC waste pipe etc. complete including painting the fittings ,cutting &making good the walls wherever required. (Sink cock, stop cocks, waste coupling are to be paid separately. (B) Hindware make/(ii) Size 450 x 300 x 180 (Cat.No.50001)

Providing fitting and fixing vitreous china flat back type lipped front urinal basin with standard flush pipe and CP brass spreader andbrass unions, etc. complete including painting of fittings and brackets, cutting and making good the walls & floors wherever required. (ii) Aquaseal (Cat. No.C0508)

Providing fitting and fixing vitreous china squatting plate urinal with automatic flushing cistern with standard flush pipe and CP brass spreader andbrass unions, etc. complete including painting of fittings and brackets, cutting and making good the walls & floors wherever required. (i) White (Cat. No. C0503)

Supplying fiting and fixing vitreous china division plate including fitting and fixing compete as directed and specified.(i) Partion Magnum (Cat. No.C0571/07)

CP Brass fittings Providing and fixing unplasticised PVC connection pipe with brass unions 45 cm length 15 mm nominal bore

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean & Wall moutain type W.C. of quality and make as approved by Engineer - in - charge.

Supplying fitting and fixing C.P. bib cock 15mm dia of approved brand as directed and specified. (G.I. & C.P pipes will be measured separately) Essco make (Delux/Sumthing spl./Tropical) (a) Bib cock short body

(b) Long body bib cock with wall flange

Supplying fitting and fixing Chrome Plated (C.P.) sink cock of approved brand as directed and specified. (G.I. & C.P pipes will be measured and paid separately) Essco brand/(b) Sink cock with "U" shape bend pipe

Providing and fixing C.P. brass angle valve for basin mixer and gyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore

Supplying, fitting and fixing Chrome Plated (C.P.) sink mixer complete as directed Sona make/ (a) Sink mixer upper/ lower spout No.2121/2122

Supplying, fitting and fixing Chrome Plated (C.P.) basin mixer complete as directed Lauret make/a) Central hole basin mixer Cat No. 1210 for wash basin

Supplying, fitting and fixing Chrome Plated (C.P.) wall mixer complete as directed. Sona make/(a) Wall mixer non telephonic Cat No.1111

Supplying fitting and fixing overhead adjustable Chrome Plated (C.P.) spray shower 15mm dia. of wall flange as directed and specified.(pipes will be measured and paid separately) (a) Supreme shower with arm/

Supplying fitting and fixing stop-cock of approved brand of size as mentioned below and directed and specified (G.I. & C.P. pipes will be measured and paid separately) (ii)20mm dia

Providing, fitting and fixing Chrome Plated TOILET PAPER holder complete as directed and specified.(d) Sona make/(i) Super (Cat. No.AL-1001)

Providing, fitting and fixing Chrome Plated bottle trap complete as directed and specified. (b) Sona make/ (i) Bottle trap indian 32mm (Cat. No.BT-0751)

Providing, fitting and fixing recessed soap tray / soap dish complete as directed and specified. (b) Sona Make/(i) Soap dish light (Cat.No.TR-0661)

Providing, fitting and fixing CP towel rail complete as directed and specified.(b) Sona make /(i) Towel rail Diplomat 300mm long (Cat.No.TR-0605)

Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 (Supreme/Prince) or other ISI approved including joining ,fitting and fixing with clamps etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. (i) 160mm dia.

(ii) 110mm dia.

(iii) 90mm dia.

Supplying fitting and fixing approved uPVC Pipes of different sizes, with all necessary 'R' brand or similar approved uP.V.C. Fittings such as bend, tee, elbow, reducer, nipple, plug, long screw fitting, clamps etc. complete at all levels including below G.L. as directed and specified.( for wash basin waste pipe)(B) (B) Concealed by chieselling or breaking brick wall/ C.C. wall/ R.C.C. wall and making good to the damaged structure. c) 32 mm dia

Providing and laying cement concrete 1:5:10(1 cement : 5 coarse sand : 10 graded stone aggregate 20mm nominal size) around P.V.C Soil and waste pipe including bed concrete as per standard design(embedded in the flooring / ground)( for soil and waste pipe) 110 & 90 mm dia

150 mm dia

Providing & fixing UPVC Floor trap of self cleansing design with CP Jali complete in all respects. (Make : Astral ) Floor Trap i) Multi floor trap

ii) Plain floor trap

Supplying, fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining ,fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. (i) 160mm dia.

(ii) 110mm dia.

(iii) 90mm dia.

Supplying fiting and fixing 45degree PVC bend of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (i) 160mm dia.

(ii) 110mm dia.

(iii) 90mm dia.

Supplying fiting and fixing PVC Plain single tee of (Supreme/ Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified.a) In exposed surfaces or in trenches. (i) 160mm dia.

(ii) 110mm dia.

(iii) 90mm dia.

Supplying fiting and fixing PVC single tee with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (i) 160mm dia.

(ii) 110mm dia.

(iii) 90mm dia.

Supplying fiting and fixing PVC single ‘Y’ of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (i) 160mm dia.

(ii) 110mm dia.

(iii) 90mm dia.

Supplying fiting and fixing PVC reducing Tee of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified.a) In exposed surfaces or in trenches. (i) 160mm x 110 mm

(ii) 110 mm x 90 mm

Supplying fiting and fixing PVC reducing Tee with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. in exposed surface or trenches as necessary complete at all levels including below G.L. as directed and specified.(i) 160mm x 110 mm

Supplying fiting and fixing PVC socket plug of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. in exposed surface or trences as necessary complete at all levels including below G.L. as directed and specified.(i) 110mm dia.

Providing fitting and fixing PVC cowel of ISI make complete as directed and specified. (i) 160mm dia.

(ii) 110mm dia.

(iii) 90mm dia.

Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 (Supreme/Prince) or other ISI approved including joining ,fitting and fixing with clamps etc.as necessary complete at all levels including below G.L as directed and specified.( for rain water ) a) In exposed surfaces or in trenches. (i) 160mm dia.

(ii) 110mm dia.

Providing and laying cement concrete 1:5:10(1 cement : 5 coarse sand : 10 graded stone aggregate 20mm nominal size) around P.V.C Soil and waste pipe including bed concrete as per standard design(embedded in the flooring / ground)( for rain water pipe)100 mm dia

Supplying, fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining ,fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified. (ii) 110mm dia.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Shoe (Plain) 110 mm Shoe

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over PVC sheet 1m x 1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement,punning,rounding the edges and making and finishing the outlet complete.

Providing and fixing Chlorinated Polyvinyle Chloride (CPVC) Pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipe (B) Concealed work including cutting chases and making good the walls etc. a) 20 mm nominal outer dia pipe

b) 25 mm nominal outer dia pipe

c) 32 mm nominal outer dia pipe

d) 40 mm nominal outer dia pipe

Supplying fitting and fixing G.I. Pipes of following sizes, with all necessary 'R' brand or similar approved G.I. Fittings such as bend, tee, elbow, reducer, nipple, plug, long screw fitting, H.W. clamps etc.complete at all levels including below G.L. as directed and specified. Internal work-Exposed on wall 15mm dia nominal bore

20mm dia nominal bore

25mm dia nominal bore

32mm dia nominal bore

40mm dia nominal bore

50mm dia nominal bore

Providing and fixing GI pipes complete with GI fittings and clamps, including cutting and making good walls etc. (internal work). Terrace and external work 65mm dia nominal bore

80mm dia nominal bore

Painting GI pipes and fittings with SYNTHETIC enamel paint over a ready mixed priming coat, both of approved quality for new work. Vertical ,Terrace and external work 15mm dia nominal bore

20mm dia nominal bore

25mm dia nominal bore

32mm dia nominal bore

40mm dia nominal bore

50mm dia nominal bore

65mm dia nominal bore

80mm dia nominal bore

Providing and fixing GI Union in GI pipes including cutting and threading the pipe and making long screws etc. complete (new work). 15mm dia nominal bore

20mm dia nominal bore

25mm dia nominal bore

32mm dia nominal bore

40mm dia nominal bore

50mm dia nominal bore

65mm dia nominal bore

80mm dia nominal bore

Providing and fixing gun metal gate valve with wheel of approved quality. 20mm dia nominal bore

25mm dia nominal bore

32mm dia nominal bore

40mm dia nominal bore

50mm dia nominal bore

65mm dia nominal bore

80mm dia nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 25 mm nominal bore

Supplying and placing plastic cylindrical vertical claused top (PCVC) tank of Sintex / Polycon / Patton make over the stagging with manhole cover with locking and cleaning arrangement including providing pads of size as required for inlet and outlet pipes 2000 Lt capacity

1500 Lt capacity

1000 Lt capacity

500 Lt capacity

Solar Water Heaters 1. System capacity : 1000 LPD SUNPOT with Recirculating Pump 2. System temperature output : 60 deg. C 3. Operating Pressure : Non-Pressurized 4. Type of System : FPC 5. No. Of Collectors / Tubes : 08 6. Application : Bathing 7. Circulation : Non-Pressurized Flow 8. Support stands for collectors : MS painted structure 9. Tank type : SS 304 10. Tank Sizes : 1000 Ltrs. 11. Insulation : PUF/Rockwool / Glasswool insulation 12. Brands : NUETECH/ Equivalent

RO Plant 500 LPH (Liter per hour) PLANT CAPACITY - 500 LPH RECOVERY - 50% ELECTRICAL CONNECTION - 415 V, 3 PHASE, 50 HZ TDS - < 100 PPM 1000L STORAGE TANK

Supply of wall hanging drinking online water cooler with bottle filler facility, made by stainless steel top and heavy duty galvanized steel frame. With cooling capacity, ADA Compliant, size 472 mm Depth X 447mm width, flexible bubbler guard , operated between 50 to 120 PSI, Chiller unit Suitable to R134a Refrigerant, Adjustable thermostat control, suitable for 220-230v/50-60 hz A/C Supply Complete with all accessories which include MD-CU29, which is an EPA registered antimicrobial copper that fights off microorganisms which include MRSA and e-coli. The water Fountain shall possess NSF-USA, Green building, energy star saving certification, and to be placed at different location of buidling. As per Enginner Incharge- Make Oasis/ Filtrin/ Eureka Forbes

Providing, laying and jointing glazed stoneware pipes grade 'A' with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete. 100mm diameter

Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand : 10 graded stone aggregate 40mm nominal size) all round S.W. pipes including bed concrete as per standard design. 100mm dia SW pipe

Providing and fixing square-mouth S.W. gully trap grade‘A’ complete with C.I. grating, brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design 150 x 100 mm size P type With Sewer bricks conforming to IS : 4885

Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement:3 coarse sand :6graded stone aggregate 20 mm nominal size) as per standard design With 20x20 mm square bar

Constructing brick masonry Catch basin 45x45x45 cm with bricks of class designation 50 in cement mortar 1:4 (1 cement : 4 coarse sand) including m.s. grating cover complete as per design. With FPS bricks

Constructing brick masonry INSPECTION chamber 60x60x90 cm with bricks of class designation 50 in cement mortar 1:4 (1 cement : 4 coarse sand) including CI cover with frame LIGHT WEIGHT complete as per design. With FPS bricks

SEWERAGE & RAIN WATER WORKS Excavating trenches in all kinds of soil of required width for pipes. including excavation for sockets and dressing of sides, ramming of bottoms, including getting out the excavated soil & then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc & disposing of surplus excavated soil as directed within a lead of 50m. 1.50 m depth Pipes 80 mm to 300 mm diameter

1.50 m to 3.00 m depth Pipes 80 mm to 300 mm diameter

Open timbering in trenches including shuttering and shoring complete. (Measurement to be taken of the face area timbered) Depth not exceeding 1.5 meter

Depth 1.5 to 3.00 meter

Providing and laying Non pressure NP 2 class (light duty) RCC pipe with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1cement : 2 fine sand ) including testing of joints etc. complete. 150 mm. dia. RCC Pipes

250 mm. dia. RCC Pipes

300 mm. dia. RCC Pipes

450 mm. dia. RCC Pipes

Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand : 10 graded stone aggregate 40mm nominal size) upto the haunches of pipes including bed concrete as per standard design 150 mm. dia.

250 mm. dia.

Constructing brick masonry manhole in cement mortar 1:4 (1 cement :4 coarse sand) RCC top slab with 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement :4 coarse sand :8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with floating coat fo neat cement and making channels in cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nminal size) finished with a floating coat of neat cement complete as per standard design. Inside size 90x80cms and 45cms deep including CI cover with frame (light duty) 455x610mm internal diamensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15kg). With common burnt clay FPS (non modular) bricks of class designation 75 (i) For Sewer Line

Extra for depth for manholes: Size 90x80cm with With common burnt clay FPS (non modular) bricks of class designation 7.5

Inside size 90x120cms and 90cms deep including CI cover with frame (MEDIUM duty) 455x610mm internal diamensions total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58kg). (i) For Sewer Line

Extra for depth for manholes: Size 90x120cm with With common burnt clay FPS (non modular) bricks of class designation 7.5

Constructing brick masonary circular manhole 1.22 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand) inside cement plaster 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement foundation concrete 1:3:6 (1 cement :3 coarse sand : 6 graded stone aggregate 40mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement, all complete as per standard design: 1.68 m deep with SFRC Cover and frame (heavy duty HD-20 grade designation) 560mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand :4 graded stone aggregate 20mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately): With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra depth for circular type manhole 1.22m internal dia (at bottom) beyond 1.68m to 2.29m With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry circular manhole 1.52 m internal dia at bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand) inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design : 2.30 m deep with SFRC Cover and frame (heavy duty HD- 20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra depth for circular type manhole 1.52 m internal dia (at bottom)beyond 2.30 m : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing orange colour safety foot rests of minimum 6 mm thick plastic encapsulated as per IS:10910 on 12 mm dia steel bar conforming to IS:1786 having minimum cross section as 23 mm x 25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm thread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

EXTERNAL WATER SUPPLY WORKS RISING MAIN AND BYE PASS ARRANGEMENT Providing and laying double flanged (Screwed/Welded) centrifugally (Spun) Ductile iron pipes of class K-9 conforming to IS 8329 150mm dia Ductile iron double flanged

100mm dia Ductile iron double flanged

Providing push-on-joints to centrifugally (Spun) Cast Iron Pipes or Ductile Iron Pipes including testing of joints and including the cost of rubber gasket : 150mm dia pipes

100mm dia pipes

Providing and fixing C.I. Sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately): 150mm diameter

100mm diameter

Provding and fixing C.I. Double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc. if required will be paid separately. a) 50mm dia

DISTRIBUTION SYSTEM Supplying fitting and fixing Pipes with all necessary fittings in exposed or in trenches including trenching and refilling the same etc complete as directed A) G.I. pipe with GI fittingsa) TATA / SAIL (Medium) 25mm nominal bore.

32mm nominal bore.

40mm nominal bore.

50mm nominal bore.

65mm nominal bore.

80mm nominal bore.

Providing and fixing gate valve with CI wheel 25mm nominal bore.

32mm nominal bore.

40mm nominal bore.

50mm nominal bore.

65mm nominal bore.

80mm nominal bore.

Constructing masonry Chamber 90X90X100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand ) for sluice valve, with C.I. surface box 100mm, top diameter, 160 mm bottom diameter and 180mm deep (inside) with chained lid and RCC top slab 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 (1 cement :5 fine sand : 10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand ) 12 mm thick finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry chamber 600 x 600 x 750 mm inside with F.P.S. brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for Sluice Valve / Air Valve, with C. I. surface box 100 mm top diameter, 160 mm bottom diameter and 180mm deep (inside) with chained lid and RCC top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 grade stone aggregate 20 mm nominal size); necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand: 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1 : 3 (1 cement : 3 coarse sand ) 12 mm thick finished with a floating coat of neat cement complete as per standard design

Water Transfer Pumps (Hydropneumatic systems) 1-nos, vertical stainless steel in-line pumps having stainless steel casing, stainless steel pump foot diffusers, stainless steel impellers, ceramic bearing, tungsten carbide shaft protection bushes and mechanical seal driven by appx 25.0 hp ,415volts 50 cycles, AC 3 phase TEFC vertical flange motor motor. Each pump shall be capable of delivering 12.0 lps @ 100 mtr head. With complete headers, fittings & foundation as per Specifications

RAIN WATER HARVESTING RECHARGE PITS Providing and laying in cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded Stone aggregate 20 mm nominal size) and curing complete,including cost of form- work,in foundation and floors.

Class M-150 brick work in 1:4 cement coarse sand mortar in foundation & plinth including supply of all materials, labour, tools and plants etc. required for proper completion of the work.

Reinforcement cement concrete work in RCC culvert slab with 1:1.5:3 (1 cement : 1.5 coarse sand and 3 gradded stone aggregate of 20 mm nominal size) excluding centering and shuttering and reinforcement.

15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. 1:3 (1 cement : 3 Coarse sand)

Providing M.S. foot rests including fixing in manoholes with 20x20x10 cm cement concrete blocks 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) as per standard design: With 20x20mm square bar

Providing and fixing in position precast RCC manhole cover and frame of required shape and approved quality. M.D. -10- Circular shape 500mm internal diameter

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level. Drilling of 300mm dia bore hole manually.

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 150 mm nominal size dia

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.

Providing and fixing gun metal non- return valve of approved quality. 65 mm nominal bore

Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required : 65mm dia

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 65mm dia

Kirloskar make sump pump Model 2200CW, 5 HP, 3 Phase, delivery pipe size 65 mm,

BORE WELL INSTALLATIONSLabour for boring hole for inserting tube well pipes through different soil/ rock media including hire charges of drill pipes, scaffolding, tools and plants as necessary and taking out the same and lowering pipes, fittings complete as directed by the Department. All types of soil 300 mm dia

Supplying, fitting and fixing pipes plain/bevel ended for casing, conforming to relevant IS codes of practice including supplying and fitting of tube well accessories, lowering of assembly pipes concentrically in the borehole followed by supplying and packing of pea gravel free from dirt, dust and other foreign materials in the annular space between the borehole and assembly pipes complete as directed by the Department. 160mm PVC PIPE

`Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.

Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 mild steel screwed and socketed/ plain ended casing pipes of required dia, conforming to IS: 4270, of reputed & approved make, including painted with outside surface with two coats of anticorrosive paint of approved brand and manufacture, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer-in-charge. 150 mm nominal size dia having minimum wall thickness 5.00 mm.

Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 plain slotted (having slot of size 1.6/3.2 mm) mild steel threaded and socketed / plain bevel ended pipe (type A) of required dia, conforming to IS:8110, of reputed and approved make, having wall thickness not less than 5.40 mm, including painted with outside surface with two coats of anticorrosive bitumestic paint of approved brand and manufacture, including hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer -in-charge. 150 mm nominal size dia

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

S.T.P 500 KLD & E.T.P 50 KLD Raw Polluted water Generation & Characteristics for Designing of the WPCES: Average Daily flow (Cum/day) =550 Hourly flow (Cum/Hr.) = 22.91 (Average Load) 24 hr HRT Assumed Characteristics: PH =6.5 BOD (mg/l) =100 COD (mg/l) =400 Suspended solids (mg/l) =600 Total Domestic Polluted water/day =550 Invert level of inlet pipe = 2m (Assumed) Treated water Characteristics: BOD = Less than 30 mg/l COD = Less than 50 mg/l Suspended solids = Less than 50 mg/l pH = 6.5 – 8.5 EQUIPMENT SPECIFICATION FOR STP The basic system comes with the following standard equipment  Two sets of Screen. Two sets of Blower &motor for air blowing in bioreactor for oxygen to bacteria & motor.  Two sets of centrifugal pump.  Two sets of Sludge pump.  Two sets of sludge recycling pump  PSF (Pressure sand filter) & ACF( Activated carbon filter)  Piping & valves.  MBBR (Moving Bed Biofilm Reactor) media  Tube deck media.  Wire & cables.  Bubble diffuser.  One main electrical switchboard/control panel for supplying power to various pumps of the system. EQUIPMENT SPECIFICATION FOR ETP The basic system comes with the following standard equipment  One sets of Screen.  Two sets of centrifugal pump.  Two sets of Sludge pump for safe disposal of Sludge  Mixing arrangement for chemicals  2 dosing metering pumps for dosing of coagulant and flocculent CIVIL STRUCTURE FOR 500 KLD STP 1 SCREEN CHAMBER VOLUME=3.6 Kilo liters (2*1.2*1.5)m Type=Under Ground Material of construction=RCC Quantity=1 2 FOG TRAP VOLUME=7.2 kilo liters (3*1.2*2)m Type =Under Ground Material of construction=RCC Quantity=1 3 EQUALIZATION TANK VOLUME=500 Kilo liters (14.3*10*3.5)m Type=Under Ground Material of construction = RCC Quantity=1 4 AERATION TANK VOLUME=500 kilo liters (14.3*10*3.5)m Type=Above Ground/semi above ground Material of construction=RCC Quantity=1 5 SETTLER TANK VOLUME=50 kilo liters (4.8*3*3.5)m Type=Above Ground/semi above ground Material of construction=RCC Quantity=1 6 BALANCE TANK VOLUME 50 kilo liters (4.8*3*3.5)m Type Under Ground/semi above ground Material of construction RCC Quantity=1 7 SLUDGE DRYING BED VOLUME=20 Kilo liters Type=Above Ground (3.4*3*2)m Material of construction=RCC Quantity=1 8 DRY SLUDGE STORAGE TANK VOLUME= 3*3 m Type= Above Ground Material of construction =RCC/Brick Quantity=1 8 TREATED WATER TANK VOLUME= 100 Kilo liters (7.4*4*3.5)m Type= Above Ground Material of construction= RCC Quantity=1 9 PLANT ROOM VOLUME=3*4 m2 Type=Above Ground Material of construction= Brick CIVIL STRUCTURE FOR 50 KLD ETP 1 SCREEN CHAMBER VOLUME = 2 Kilo liters (2*1*1)m Type= Under Ground Material of construction= RCC Quantity= 1 2 EQUALIZATION TANK VOLUME= 35 Kilo liters (5*3*2) Type= Under Ground Material of construction= RCC Quantity= 1 3 Chemical Dosing Tank VOLUME = 2 Kilo liters (2*1*1)m Type= Above graound Material of construction =RCC Quantity =1 4=Settler tank VOLUME=10 Kilo liters (2.5*2*2)m Type=Under Ground Material of construction=RCC Quantity=1

FIRE FIGHTING WORK SUBHEAD-I INTERNAL FIRE HYDRANT & SPRINKLER SYSTEM 1.NOC from fire authority shall be in the scope of Contractor . Only fee paid to the fire authority shall be reimbursed against the submission of the receipt and nothing shall be paid extra. 2. All the Fire Fighting works shall be done in compliance of Fire Fighting authority requirement. Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) (a)Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520 b) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required. (d) Suitable cement concrete foundation duly plastered and with anti vibration pads. 900 lpm at 35 m Head

450 lpm at 35 m Head

Providing,erection testing & commissioning of pressure gauge 100 mm dia (0-10Kg/cm2)

Providing & fixing flow switch in following sizes M.S.pipe including connection etc as required. 100mm dia

150mm dia

Providing ,Fixing ,Testing & Commissioning of Air Release Valve (25mm)

Providing,Fixing,Testing & Commissioning of Mild Steel Black Pipe(IS:1239part-I) Heavy class including cutting, screwing, welding etc. and providing all fittings viz forged steel screwed fitting upto 50mm dia and bolt welded above 50mm dia flanges, bends, tees, reducers, elbow, clamps, hangers etc including cutting holes and chases in brick or RCC walls/ slabs and making good the same to the approval of Engineer-in-charge/ consultant complete including painting with one coat of primer and two or more coats of synthetic enamel paint of approved make and shade including steel work complete as required.(Make:TATA/JINDAL/NEZONE) 25 mm dia

32 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

100 mm dia

150 mm dia

200 mm dia

Supplying & Fixing,cast iron body Butterfly Valves with matching flanges, rubber insertion, nuts, bolts and washer etc (IS:13095) of following size complete as reqd. (MAKE:KOLEY/KALPANA/AUDCO) 80 mm dia

100 mm dia

150 mm dia

200 mm dia

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.

Single headed Gunmetal Providing,Fixing, testing &Commissioning of Single Headed Gun Metal ISI Marked oblique pattern Hydrant Landing Valve with 80 mm dia, flanged inlet & 63 mm dia instantaneous type female outlet complete with cap and chain, twist release lug and all accessories as per IS:5290-19833 (Type-'A') and specifications complete as reequired . (MAKE:ESSEL/WINCO/NEWAGE)

Fire Hydrant Valve, Double headed, Gunmetal, IS:318-LTB2 Grade, 100mm N.B Flanged inlet, Brass Spindle, 02 individually controlled 63mm Female Instantaneous Oblique Outlet, Complete with PVC Blank Cap & GI Chain, Bearing IS:5290 Mark, Flange O.D.220mm, PCD 180mm, Eight 19mm Dia Holes

Providing RRL Hose with ISI Marked (IS:636) 63 mm dia X15 M long complete with instantaneous type Gun Metal 3 mm dia ISI Marked male & female couplings (IS:903) bound & riveted to hose pipes with copper rivets and copper wire complete as reqd. ( MAKE: NIRMAL RUBBER/NEWAGE) Gun Metal

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle.Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 30 m

Providing & Fixing of Gun Metal 63 mm dia Short Branch Pipe with 20 mm dia nozzle, ISI marked (IS:903) complete as required. (Make: ESSEL/WINCO/NEWAGE). Gun metal

Fireman Axe-made of carbon steel with rubber insulated handle tested to 20,000 Volts as per IS:926 Make: NEWAGE

Fire shaft door fabricated out of M.S. sheet and frame, door size of 1200 (W) x 2100 (h) with 4 mm thick glass, suitable Rubber beading and Locking arrangement and complete door shall be powder coated with red color powder coating

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required. 700mm

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Pendent Sprinkler

Upright Sprinkler

Horizontal side wall sprinkler

Concealed sprinkler

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 2 way-100 mm dia M.S. Pipe

SUBHEAD-II : FIRE EXTINGUSHER Providing, storing, handling, shifting, installation, testing and commissioning of halon free portable fire Extinguishers as described below: Refilling & Servicing of CO2 Type Fire Extinguisher with ISI Mark refill etc. complete / 4.5kg

Refilling & Servicing of CO2 Type Fire Extinguisher with ISI Mark refill etc. complete / 6.5kg

Refilling & Servicing of CO2 Type Fire Extinguisher with ISI Mark refill etc. complete / 9.0kg

Supply, Installation, Fixing of DRY CHEMICAL POWDER Fire Extinguisher confirming to IS: 2171 with ISI mark and CO2 cartridge will be confirming to IS: 4947 with ISI mark, Powder will be confirming to IS: 4308 with ISI Mark (Extinguisher will be TROLLEY MOUNTED).(50 KG) BRAND : FIRESTOP / FIREND / FIRE SHIELDC

Supply, Installation, Fixing of DRY CHEMICAL POWDER Fire Extinguisher confirming to IS: 2171 with ISI mark and CO2 cartridge will be confirming to IS: 4947 with ISI mark, Powder will be confirming to IS: 4308 with ISI Mark (Extinguisher will be TROLLEY MOUNTED)(75 KG) BRAND : FIRESTOP / FIREND / FIRE SHIELD

Providing and fixing Fire related signages printed on photoluminescent U1000 aluminium sheet of 1.0 mm (+-10%) containing Lumigen II as base chemical, covered under UV stablized coating and of appropriate size including fixing on wall, door, ceiling etc. with proper clamps, hangers, cleats, anchor fasteners etc. complete in all respects as directed by Engineer-in-charge.

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. 25 mm Conduit

32 mm Conduit

EXTERNAL FIRE FIGHTING WORK SUBHEAD-I EXTERNAL FIRE HYDRANT & FIRE PUMPS Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required : (a)Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. (b)Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (d)Suitable cement concrete foundation duly plastered 2280 lpm at 88 m Head

Supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Diesel Driven Pump) Horizontal type,multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. Suitable HP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12 /24 volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required. M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. 2280 lpm at 88 m Head

Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520. Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325. M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. 300 lpm at 88 m Head

Providing ,erection,Testing & Commissioning of Pressure Switch (MAKE:INDFOSS)

Supplying and fixing Air Vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.

Providing,erection testing & commissioning of pressure gauge 100 mm dia (0-10Kg/cm2)

Supply,installation,testing & commissioning of 150 mm dia installation control valve assembly comprising of vertical wet alarm valve, hydraulic alarm motor & gong, 15 mm dia Test Valve, 50 mm dia , Drain Valve and all necessary trimming connections including 02 nos. pressure gauge as per manufacturers catalogue complete as reqd.(UL/FM/LPC Listed/Approved)(Make : HD FIRE ) 150mm dia

Providing,Fixing,Testing & Commissioning of Mild Steel Black Pipe(IS:1239part-I) Heavy class including cutting, screwing, welding etc.complete with all fittings (butt welded) viz flanges, bends, tees, elbows, reducers etc including excavation (upto 1.5 m Deep), back filling and removal of surplus soil & providing anti corrosive treatment(coating and wrapping) as per IS:10221 with 4 mm thick tape complete as reqd. (MAKE:TATA/JINDAL/NEZONE) 150 mm. Dia

200 mm. Dia

Providing, Erection, Testing & Commissioning of Cast Iron Sluice Valve/ Gate Valve confirming to IS:14846/2000 complete with matching flanges, rubber insertion, nuts, bolts and washer etc of following size complete as required (MAKE:KOLEY/KALPANA/AUDCO) 80mm dia

100mm dia

150mm dia

200mm dia

Supplying & Fixing Cast iron body Non Return valves complete with matching flanges, rubber insertion, nuts, bolts and washer etc. (IS:5312) of following sizes complete as reqd. (Make:Koley/Kalpana/Audco) 100mm dia

150mm dia

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. 100mm dia

150mm dia

200mm dia

250mm dia

EXTERNAL HYDRANT SYSTEM Providing,Fixing, testing &Commissioning of Single Headed Gun Metal ISI Marked oblique pattern Hydrant Landing Valve with 80 mm dia, flanged inlet & 63 mm dia instantaneous type female outlet complete with cap and chain, twist release lug and all accessories as per IS:5290-19833 (Type-'A') and specifications complete as reequired . (MAKE:ESSEL/WINCO/NEWAGE) External yard hydrant

Providing RRL Hose with ISI Marked (IS:636) 63 mm dia X15 M long complete with instantaneous type Gun Metal 3 mm dia ISI Marked male & female couplings (IS:903) bound & riveted to hose pipes with copper rivets and copper wire complete as reqd. ( MAKE: NIRMAL RUBBER/NEWAGE)

Providing & Fixing of Gun Metal 63 mm dia Short Branch Pipe with 20 mm dia nozzle, ISI marked (IS:903) complete as required. (Make: ESSEL/WINCO/NEWAGE). Gun metal

Providing & fixing of weather proof hose cabinets fabricated from 16 S.W.G. M.S. Sheet with centre opening full front glass door and locking arrangement, suitable to accommodate one landing valve (Yard Hydrant ), 2nos.15M long hoses and 1 no. Branch pipe with nozzle . The cabinet shall be painted with one coat of primer and 2 or more coats of synthetic enamel paint of approved make & shade and shall be suitably mounted on a raised masonry platform complete as reqd.(Make:self Fabricated) a) 900X600X450

Providing & Fixing of Gun Metal fire Brigade Connection (inlet collection head) consisting of 63mm instantaneous type male coupling with built in check valves and 150 mm dia flanged outlet complete with bolts, nuts and rubber insertions as per IS:904-1983 complete as reqd.MAKE: ESSEL/WINCO/NEWAGE b) 04 way

Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc 4 Core X 16 sqmm. Aluminium Armoured

4 Core X 10 sqmm. Aluminium Armoured

3.5Core X 50 sqmm. Aluminium Armoured

3.5 Core, X 35 sqmm. Aluminium Armoured

3.5 Corex 300 sqmm. Aluminium Armoured

3.5 Corex 120 sqmm. Aluminium Armoured

Supply and fixing in position 1 m wide Insulation mat made of elastomeric polymers Material (Class -A) of 415V grade as per IS 15642-2006 . Thickness of insulation mat shall be not less than 3 mm to withstand 1.1 KV dielectric strength AS PER IS 15652 : 2006. It should be complete as per specifications & directions of Engineer-in-charge. It should be complete as per specifications & directions of Engineer-in-charge.

Supplying and making end termination with brass double compression gland and aluminium lugs for following size of XLPE insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. It should be complete as per specifications & directions of Engineer-in-charge. 4 Core X 16 sqmm. Aluminium Armoured

4 Core X 10 sqmm. Aluminium Armoured

3 Core, X 50 sqmm. Aluminium Armoured

3 Core, X 35 sqmm. Aluminium Armoured

3.5 Corex 300 sqmm. Aluminium Armoured

3.5 Corex 120 sqmm. Aluminium Armoured

Supplying , installating, Testing & commissioning of XLPE insulated & PVC sheathed 1.1 KV grade armoured Copper control cables for various equipment through walls / ceilings with appropriate clamps / fixing arrangements and complete with termination as per manufacturer's specifications & as directed by Engineer-in-charge. 6 C x 2.5 Sqmm

2 C x 4.0 Sqmm

2 C x 2.5 Sqmm

INTERNAL ELECTRICAL WORK INTERNAL WIRING Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group -B

Group -C

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. Group -B

Group C

Wiring for circuit wiring with P.V.C. insulated single core unsheathed industrial (Multistrand) cable HFFR/ZHFR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco or Equivalent Make as approved by the Deptt.) cable in surface/ recessed ISI marked Steel conduit pipe (AKG or equivalent as approved by the Deptt.) rigid low halogen SFT PVC IS: 9537 Part - III conduit wiring system. With 3 x 1.5 sq. mm. cable in 20 mm dia. rigid Steel conduit.

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable HFFR/ZHFR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco or Equivalent Make as approved by the Deptt.) in ISI marked Steel conduit pipe (AKG or equivalent as approved by the Deptt.) with earth continuity in surface/ recessed conduit wiring system. With 2 x 2.5 sq. mm. + earth continuity with 1x1.5 sq. mm. in 20 mm. dia. rigid Steel conduit.

b) with 2 x 4 sq. mm. + earth continuity with 1x2.5 sq. mm. in 20 mm. dia. rigid Steel conduit.

c) with 2 x 6 sq. mm. + earth continuity with 1x 4 sq. mm. in 25 mm. dia. rigid Steel conduit.

With 2 x 10 sq. mm. + earth continuity with 1x 6 sq. mm. cable in 25 mm. dia. rigid Steel conduit.

With 2 x 16 sq. mm. + earth continuity with 1x 10 sq. mm. cable in 32 mm. dia. rigid Steel conduit.

c) with 4x 6 sq. mm. + earth continuity with 2x4 sq. mm. cable in 32 mm. dia. rigid Steel conduit.

With 4 x 10 sq. mm. + earth continuity with 2x6 sq. mm. cable in 40 mm. dia. rigid Steel conduit.

With 4 x 16 sq. mm. + earth continuity with 2x10 sq. mm. cable in 40 mm. dia. rigid Steel conduit.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required. .

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing 30 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 A "C" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required 20mm dia conduit

25mm dia conduit

32mm dia conduit

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20mm dia conduit

25mm dia conduit

32mm dia conduit

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 A Switch

2 Way 5/6 A switch

15/16 A switch

3 pin 5/6 A socket outlet

6 pin 15/16 A socket outlet

Telephone socket outlet

TV antenna socket outlet

Bell push

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1 or 2 Module (75mmX75mm)

3 Module (100mmX75mm)

4 Module (125mmX75mm)

6 Module (200mmX75mm)

8 Module (125mmX125mm)

12 Module (200mmX150mm)

Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required.

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 2 Pair

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required. 100 mm X 100 mm X 60 mm deep

150 mm X 150 mm X 60 mm deep

200 mm X 300 mm X 60 mm deep

FANS & LIGHT FIXTURES: Supply, installation, testing & commissioning of Recess mounted Cleanroom LED 2'x2'(45 watt) bottom openable screwless luminaire delivering an initial system lumen of 4200 lumens & the luminaire shall be with system efficacy ≥ 100 lm / W. The Housing shall be epoxy polyester powder coated CRCA with HET diffuser, IP54. The bottom frame of Luminaire shall be screwless fixed with magnetic locking system and non hygroscopic VHB gasket to ensure dust proofing. It shall have wishbone mechanism for perfect bottom frame alignment. The operating CCT shall be 5700K with CRI of ≥80. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V , THD ≤ 10% & PF ≥ 0.95, 50,000 Hrs LED Life with L70 Criteria. The LED Driver shall be easily avaiable in India for repair and service. Luminaire shall have minimum surge protection of 2KV.The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along with Photo Biological Safety Standard. Similar to Wipro Cat No.: LC20-551-CCL-57-XM or equivalent

Supply, installation, testing & commissioning of Recess mounted LED 2'x2' UGR luminaire(36 Watt) delivering an initial system lumen of 3300 lumens & the luminaire shall be with system efficacy ≥ 100 lm / W. The Housing shall be powder coated CRCA with microprecision optics diffuser to avoid Glare, UGR shall be less than 19. The operating CCT shall be 5700K with CRI of ≥80. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V , THD ≤ 10% & PF ≥ 0.95, 50,000 Hrs LED Life with L70 Criteria. The LED Driver shall be easily avaiable in India for repair and service. Luminaire shall have minimum surge protection of 2KV.The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along with Photo Biological Safety Standard. Similar to Wipro Cat No.: CRCO10R033HP57UGR or equivalent

Supply, installation, testing & commissioning of Recess mounted LED 2'x2' luminaire(45 Watt) delivering an initial system lumen of 4300 lumens & the luminaire shall be with system efficacy ≥ 120 lm / W. Housing: CRCA, Optics: polycarbonate/PMMA/Polysterene, IP20 Protection. The operating CCT shall be 5700K with CRI of ≥80. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V , THD ≤ 10% & PF ≥ 0.95, 50,000 Hrs LED Life with L70 Criteria. The LED Driver shall be easily avaiable in India for repair and service. The LED shall be SMD type. Luminaire shall have minimum surge protection of 2KV.The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along with Photo Biological Safety Standard. Similar to Wipro Cat No.: CRCO10R036HP57HEG2 or equivalent

Supply, installation, testing & commissioning of Recessed Round Led Downlighter(40 Watt) delivering an initial system lumen of 4100 lumens & the luminaire shall be with system efficacy ≥ 100 lm / W. Housing: Die Cast Aluminium. IP20 , Optics: Reflector with Glass . The operating CCT shall be 57000K with CRI ≥80. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V , & PF ≥ 0.9, 50,000 Hrs LED Life with L70 Criteria. The LED Driver shall be easily avaiable in India for repair and service. The LED shall be COB type. Luminaire shall have minimum surge protection of 2KV.The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacturer along with Photo Biological Safety Standard. Similar to Wipro Cat No.: LD56-501-060-57-XX or equivalent

Supply, installation, testing & commissioning of Recessed Round Led Downlighter(20 Watt) delivering an initial system lumen of 2000 lumens & the luminaire shall be with system efficacy ≥ 100 lm / W. Housing: Die Cast Aluminium. IP20 , Optics: Reflector with Glass . The operating CCT shall be 57000K with CRI ≥80. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V , & PF ≥ 0.9, 50,000 Hrs LED Life with L70 Criteria. The LED Driver shall be easily avaiable in India for repair and service. The LED shall be COB type. Luminaire shall have minimum surge protection of 2KV.The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacturer along with Photo Biological Safety Standard. Similar to Wipro Cat No.: LD56-251-060-57-XX or equivalent

Supply, installation, testing & commissioning of Recess Mounted Round Led Downlighter(15 Watt) delivering minimum system lumen of 1650 lm & the luminaire shall be with system efficacy ≥ 110 lm / W. Housing: Die Cast Aluminium. IP40 , Optics: PMMA/Polysterene Diffuser. The operating CCT shall be 5700K with CRI of ≥80. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V , THD ≤ 10% & PF ≥ 0.9, 50,000 Hrs LED Life with L70 Criteria. The LED Driver shall be easily avaiable in India for repair and service. The LED shall be SMD type. Luminaire shall have minimum surge protection of 2KV.The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacturer along with Photo Biological Safety Standard. Similar to Wipro Cat No.: LD06 15W or equivalent

Supply, installation, testing & commissioning of surface Mounted Round Led Downlighter(15 Watt) delivering minimum system lumen of 1650 lm & the luminaire shall be with system efficacy ≥ 110 lm / W. Housing: Die Cast Aluminium. IP20 , Optics: PMMA/Polysterene Diffuser. The operating CCT shall be 5700K with CRI of ≥80. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V , THD ≤ 10% & PF ≥ 0.9, 50,000 Hrs LED Life with L70 Criteria. The LED Driver shall be easily avaiable in India for repair and service. The LED shall be SMD type. Luminaire shall have minimum surge protection of 2KV.The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacturer along with Photo Biological Safety Standard. Similar to Wipro Cat No.: LD06 15W SM or equivalent

Supply, installation, testing & commissioning of surface/recessed Mounted Round Led Downlighter (10 Watt)delivering minimum system lumen of 900 lm & the luminaire shall be with system efficacy ≥ 100 lm / W. Housing: Die Cast Aluminium. IP20 , Optics: PMMA/Polysterene Diffuser. The operating CCT shall be 5700K with CRI of ≥80. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V , THD ≤ 10% & PF ≥ 0.9, 50,000 Hrs LED Life with L70 Criteria. The LED Driver shall be easily avaiable in India for repair and service. The LED shall be SMD type. Luminaire shall have minimum surge protection of 2KV.The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacturer along with Photo Biological Safety Standard. Similar to Wipro Cat No.: LD06-111-XXX-57WSM or equivalent

Supply, installation, testing & commissioning of 4ft Linear LED luminaire(20 Watt) delivering an initial system lumen of 2000 lumens & the luminaire shall be with system efficacy ≥ 100 lm / W. The luminaire Housing shall be made of extruded Aluminium & the diffuser shall be of polycarbonate/PMMA. The operating CCT shall be 6500K with CRI of ≥80. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V , THD ≤ 10% & PF ≥ 0.95 , 50,000 Hrs LED Life with L70 Criteria, IP20. The LED Driver shall be easily avaiable in India for repair and service. The LED shall be SMD type. Luminaire shall have minimum surge protection of 2KV.The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along with Photo Biological Safety Standard. Similar to Wipro Cat No.: LL20-281-XXX-65AL5 or equivalent

Supply, installation, testing & commissioning of 4ft Linear LED luminaire(40 Watt) delivering an initial system lumen of 4000 lumens & the luminaire shall be with system efficacy ≥ 100 lm / W. The luminaire Housing shall be made of extruded Aluminium & the diffuser shall be of polycarbonate/PMMA. The operating CCT shall be 5700K with CRI of ≥80. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V , THD ≤ 10% & PF ≥ 0.95 , 50,000 Hrs LED Life with L70 Criteria, IP40. The LED Driver shall be easily avaiable in India for repair and service. The LED shall be SMD type. Luminaire shall have minimum surge protection of 2KV.The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along with Photo Biological Safety Standard. Similar to Wipro Cat No.: LL24-541-XXX-57-XX or equivalent

Supply, installation, testing & commissioning of 2ft Linear LED luminaire(10 Watt) delivering minimum system lumen of 900 lumens & the luminaire shall be with system efficacy ≥ 90 lm / W. The luminaire Housing shall be made of PC & the diffuser shall be of polycarbonate/PMMA. The operating CCT shall be 6500K with CRI of ≥80. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V , THD ≤ 20% & PF ≥ 0.95 , 50,000 Hrs LED Life with L70 Criteria, IP20. The LED Driver shall be easily avaiable in India for repair and service. The LED shall be SMD type. Luminaire shall have minimum surge protection of 2KV.The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along with Photo Biological Safety Standard. Similar to Wipro Cat No.: LL20-111-XXX-65NE3 or equivalent

Supply, installation, testing & commissioning of Bulk Head (10 Watt)Luminare delivering an initial system lumen of 1000 lumens & the luminaire shall be with system efficacy ≥ 100 lm / W. Housing: Die Cast Aluminium. IP65 ,IK07 , Diffuser : OPAL Polycarbonate. The operating CCT shall be 5700K with CRI of ≥70. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V , THD ≤ 10% & PF ≥ 0.95, 50,000 Hrs LED Life with L70 Criteria. The LED Driver shall be easily avaiable in India for repair and service. The LED shall be SMD type. Luminaire shall have minimum surge protection of 2.5KV.The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along with Photo Biological Safety Standard. Similar to Wipro Cat No.: LW07-141-XXX-57-G1 or equivalent

Supply of LED Up down Lighter with Extruded Aluminium/ standard alloy/ CRCA housing with glass cover with integral constant current driver input operating voltage range 150V – 270V 50Hz AC supply, prewired upto the terminal block. System lumen output ≥ 2158 lumens with luminaire efficacy ≥ 85lm/W, lumen maintainence of 70% at the end of 35000 burning hours, CCT of 3000K, CRI≥70, surge proctection of ≥ 3kv and IP≥65 protected. LM 79 report to be submitted for luminaire from NABL accrediated lab and LM 80 for LED source issued by LED manufacture. similar to Wipro CAT No. LW32-321-022-30-XX or equivalent).

Supply, installation, testing & commissioning of LED FLOOD Light Luminaire(70 Watt) delivering minimum system lumen of 8000 lumens & the luminaire shall be with system efficacy ≥ 100lm/W. Housing: Die Cast Aluminium . IP66 , Optics: PC Reflector. The operating CCT shall be 5700K with CRI of ≥70. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V , THD ≤ 10% & PF ≥ 0.9, 50,000 Hrs LED Life with L70 Criteria.The LED Driver shall be easily avaiable in India for repair and service. The LED shall be SMD type. Luminaire shall have minimum surge protection of 4KV.The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along with Photo Biological Safety Standard. Similar to Wipro Cat No.: Alpha 80W or equivalent

Supply, installation, testing & commissioning of LED FLOOD Light Luminaire(90 Watt) with a minimum system lumen of 10000 lumen & the luminaire shall be with system efficacy ≥ 100lm/W. Housing: Die Cast Aluminium . IP66, Optics:Toughened Glass. The operating CCT shall be 5700K with CRI of ≥70. The luminaire shall be with BIS Registered electronic driver with input voltage range of 120 to 300V , THD ≤ 10% & PF ≥ 0.9, 50,000 Hrs LED Life with L70 Criteria.The luminaire shall Auto Cutoff at Low and High Voltage and will resume normal work once voltage in 120 to 300V.The luminaire should also be capable of 440V withstand for 8 hours. The LED Driver shall be Potted Driver for longer life/heat mangement and shall be easily avaiable in India for repair and service. The LED shall be SMD type. Luminaire shall have minimum surge protection of 4KV.The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along with Photo Biological Safety Standard. Similar to Wipro Cat No.: LF20-122-060-57-G2 or equivalent

Supply, installation, testing & commissioning of LED FLOOD Light Luminaire(120 Watt) with a minimum system lumen of 12000 lumen & the luminaire shall be with system efficacy ≥ 100lm/W. Housing: Die Cast Aluminium . IP66, Optics:Toughened Glass. The operating CCT shall be 5700K with CRI of ≥70. The luminaire shall be with BIS Registered electronic driver with input voltage range of 120 to 300V , THD ≤ 10% & PF ≥ 0.9, 50,000 Hrs LED Life with L70 Criteria.The luminaire shall Auto Cutoff at Low and High Voltage and will resume normal work once voltage in 120 to 300V.The luminaire should also be capable of 440V withstand for 8 hours. The LED Driver shall be Potted Driver for longer life/heat mangement and shall be easily avaiable in India for repair and service. The LED shall be SMD type. Luminaire shall have minimum surge protection of 4KV.The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along with Photo Biological Safety Standard. Similar to Wipro Cat No.: LF20-132-060-57-G2 or equivalent

Supply, installation, testing & commissioning of LED FLOOD Light Luminaire(200 Watt) with a minimum system lumen of 20000 lumen & the luminaire shall be with system efficacy ≥ 100lm/W. Housing: Die Cast Aluminium . IP66, Optics:Toughened Glass. The operating CCT shall be 5700K with CRI of ≥70. The luminaire shall be with BIS Registered electronic driver with input voltage range of 120 to 300V , THD ≤ 10% & PF ≥ 0.9, 50,000 Hrs LED Life with L70 Criteria.The luminaire shall Auto Cutoff at Low and High Voltage and will resume normal work once voltage in 120 to 300V.The luminaire should also be capable of 440V withstand for 8 hours. The LED Driver shall be Potted Driver for longer life/heat mangement and shall be easily avaiable in India for repair and service. The LED shall be SMD type. Luminaire shall have minimum surge protection of 4KV.The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along with Photo Biological Safety Standard. Similar to Wipro Cat No.: LF20-272-060-57-G2 or equivalent

Supply, installation, testing & commissioning of Wall mounted Led Patient Bed light IP20 (25 Watt)consuming a total system wattage of 31W with options of glare free downlight for reading and examination, up light for ambient lighting delivering an initial system lumen of 2533 lumens. Housing: non corrosive Extruded Aluminium with extruded ribbed translucence PMMA diffuser and self illuminated rocker switches. The luminaire shall have variable adjustment 10W Upward, 20W downward and 0.5W LED Bulb for generating multiple lighting modes as per the needs of Patient and doctor as well. The luminaire shall have optional suspended remote power switch for easy use in case of critical patrient care. The operating CCT shall be 5700K with CRI of ≥80. The luminaire shall be with electronic driver with input voltage range of 150 to 270V ,PF ≥ 0.95, 50,000 Hrs LED Life with L70 Criteria. The LED Driver shall be easily avaiable in India for repair and service. The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture. Similar to Wipro Cat No: LW04-411-XXX-57-WS or equivalent

Supply, installation, testing & Commissioning of non integral flexible LED strip light suitable for indoor applications. The strip shal be in 5m spools and shall be abe to cut at marked intervals to suit desired length.The wattage shall be 5W per metre. Similar to Wipro Cat No.: LS06-005-120-WH-50 + LG40-24 or equivalent

Supply, installation, connecting, testing and commissioning of illuminated exit signage including built in battery & charger capable of working for 2 hr duration mounted on ceiling/wall complete with the approved EXIT self adhesive labels as per site requirement as required including connection with 1.5 sqmm FRLS PVC insulated copper conductor similar to Bajaj BSEL 03 LED SSD WBB GREEN or equivalent

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374- 2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Supplying, erection, connecting, testing and commissioning of 400 mm wall fan complete in all respect including fixing wiring connection etc Similar to havells Platina

Supplying, erection, connecting, testing and commissioning of 750 mm wall circulating fan complete in all respect including fixing wiring connection etc Similar to Havells Variant in sweep

Supplying, erection, connecting, testing and commissioning of following size heavy duty exhaust fan(900 RPM) complete and connection with 3 core flexible wire. 300 mm

Supply of Recess mounted PIR based motion sensor, IP20 with a 360 degree detection pattern and detection area of 7m at a mounting height of 2.8m. The sensor shall work on advanced Passive Infrared Technology with adjustable off delay timing of 1-90min through IR remote. It shall be suitable for maximum system load of 10A and supply voltage 230V AC±10%, 50 Hz. Similar to Wipro cat Ref.: GLPS01R0101A or equivalent

SITC of LED Wall bracket Luminaire with E27 base lamp holder suitable for LED bulb of wattage 12W with chrome lamp cup. Similar to Wipro LM91 or equivalent

M.V. PANELS/ DISTRIBUTION BOARD Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way , Double door

12 W SPN DB

Supplying and fixing of following ways,horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess ,complete with tinned copper bus bar, neutral link, earth bar, din bar,interconnections, powder painted including earthing etc. as required. ( But without MCB/RCCB/Isolator) 4 way Double door

6 way Double door

8 way Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 4 way Double door

8 way Double door

12 way Double door

Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required Single pole

Triple pole

Supply and fixing of single phase energy meter 10 to 60 Amp. capacity fitted in integral box on wall complete in all respect

Supply and fixing of Three phase energy meter 20 to 80 Amp. capacity fitted in integral box on wall complete in all respect

Acedmic BlockPanels Same as above description, but following mountings. Sub LT Panel INCOMER:- 1nos ACB 1000A 4P EDO OL,SC,EF with display (minimum 03 line & maximum 04 line) with communication module for real data assessment like events,fault and all current parameters 1 Set phase indication lights (R, Y, B) 1 No. Volt Meter (digital type) with inbuilt VSS & control fuses. 1 No. 0-1000 Amp. Ammeter (digital type) with inbuilt ASS BUS BARS:- 1600 Amps. TP&N aluminium bus bars (36 KA) OUT GOINGS:- 8 Nos. 250 Amps. FP MCCB (36KA) 3 Nos. 100A FP, MCCB (36KA).

Same as above description, but following mountings. (UPS/Critical Main Panel) INCOMER 1 Nos. 200 Amps. FP MCCB (25KA) 1 Set phase indication lights (R, Y, B) 1 No. Volt Meter (digital type) with inbuilt VSS & control fuses. 1 No. 0-200 Amp. Ammeter (digital type) with inbuilt ASS BUS BARS:- 250 Amps. TP & N aluminium bas bar (25KA) OUT GOINGS:- 7 Nos. 100 Amps FP MCCB (16KA)

Same as above description, but following mountings. (UPS/Critical Floor Panel) INCOMER 1 Nos. 100 Amps. FP MCCB (25KA) 1 Set phase indication lights (R, Y, B) 1 No. Volt Meter (digital type) with inbuilt VSS & control fuses. 1 No. 0-100 Amp. Ammeter (digital type) with inbuilt ASS BUS BARS:- 160 Amps. TP & N aluminium bas bar (25KA) OUT GOINGS:- 7 Nos. 40 Amps FP MCB (16KA)

Same as per description, as per following mountings ( Floor Panel) Incomer 1 No. 250 A FP MCCB (36 KA) 1 Set phase indication lights (R, Y, B) 1 No. Volt Meter (digital type) with inbuilt VSS & control fuses. 1 No. 0-250 Amp. Ammeter (digital type) with inbuilt ASS BUS BARS:- 320 Amps. TP&N aluminium bus bars (36 KA) OUT GOINGS:- 10 Nos. 63 Amps. FP MCB (25KA) 3 Nos. 40 amp. FP MCB (10 KA)

Same as above description, but following mountings. (HVAC Power Distribution Panel) INCOMER 1 No. 1250 A FP MCCB (50 KA) 1 Set phase indication lights (R, Y, B) 1 No. Volt Meter (digital type) with inbuilt VSS & control fuses. 1 No. 0-800 Amp. Ammeter (digital type) with inbuilt ASS BUS BARS:-1600 Amps. TP & N aluminium bas bar (50KA) OUT GOINGS:- 10 Nos. 160 Amps FP MCCB (16KA) 10 Nos. 100/63 Amps FP MCCB (16KA)

Admin Block Panels Same as above description, but following mountings. Sub LT Panel INCOMER:- 1 Nos. 630 Amps. FP MCCB(50 KA) 1 Set phase indication lights (R, Y, B) 1 No. Volt Meter (digital type) with inbuilt VSS & control fuses. 1 No. 0-800 Amp. Ammeter (digital type) with inbuilt ASS BUS BARS:- 800 Amps. TP&N aluminium bus bars (50 KA) OUT GOINGS:- 8 Nos. 160A TPN, MCCB (36KA). 2 Nos. 63 Amp. FP, MCB (36KA)

Same as above description, but following mountings. (UPS/Critical Panel) INCOMER 1 Nos. 100 Amps. FP MCCB (25KA) 1 Set phase indication lights (R, Y, B) 1 No. Volt Meter (digital type) with inbuilt VSS & control fuses. 1 No. 0-160 Amp. Ammeter (digital type) with inbuilt ASS BUS BARS:- 100 Amps. TP & N aluminium bas bar (25KA) OUT GOINGS:- 7 Nos. 63 Amps FP MCB (25KA)

Same as above description, but following mountings. (Light & Power Floor Panel) INCOMER 1 Nos. 160 Amps. FP MCCB (25KA) 1 Set phase indication lights (R, Y, B) 1 No. Volt Meter (digital type) with inbuilt VSS & control fuses. 1 No. 0-160 Amp. Ammeter (digital type) with inbuilt ASS BUS BARS:- 100 Amps. TP & N aluminium bas bar (25KA) OUT GOINGS:- 6 Nos. 63 Amps FP MCB (25KA) 2 Nos. 40 Amps FP MCB (25KA)

Same as above description, but following mountings. (HVAC Power Distribution Panel) INCOMER 1 Nos. 630 Amps. TPN MCCB (50KA) 1 Set phase indication lights (R, Y, B) 1 No. Volt Meter (digital type) with inbuilt VSS & control fuses. 1 No. 0-630 Amp. Ammeter (digital type) with inbuilt ASS BUS BARS:- 800 Amps. TP & N aluminium bas bar (50KA) OUT GOINGS:- 10 Nos. 100 Amps FP MCCB (36KA) 4 Nos.63 Amps FP MCB (36KA)

Library Block Same as above description, but following mountings. Sub LT Panel INCOMER:- 1 Nos. 400 Amps. TPN ACB EDO(36 KA) with electronic releases. 1 Set phase indication lights (R, Y, B) 1 No. Volt Meter (digital type) with inbuilt VSS & control fuses. 1 No. 0-800 Amp. Ammeter (digital type) with inbuilt ASS BUS BARS:- 800 Amps. TP&N aluminium bus bars (36 KA) OUT GOINGS:- 7 Nos. 63A TPN, MCB (36KA). 7 Nos. 40 Amp. FP, MCB (36KA)

Same as above description, but following mountings. (UPS/Critical Panel) INCOMER 1 Nos. 100 Amps. FP MCCB (25KA) 1 Set phase indication lights (R, Y, B) 1 No. Volt Meter (digital type) with inbuilt VSS & control fuses. 1 No. 0-160 Amp. Ammeter (digital type) with inbuilt ASS BUS BARS:- 100 Amps. TP & N aluminium bas bar (25KA) OUT GOINGS:-7 Nos. 40 Amps FP MCB (25KA)

Same as above description, but following mountings. (HVAC Power Distribution Panel) INCOMER 1 Nos. 400 Amps. MCCB (36KA) 1 Set phase indication lights (R, Y, B) 1 No. Volt Meter (digital type) with inbuilt VSS & control fuses. 1 No. 0-400 Amp. Ammeter (digital type) with inbuilt ASS BUS BARS:- 630 Amps. TP & N aluminium bas bar (36KA) OUT GOINGS:- 7 Nos. 100 Amps FP MCCB (36KA) 2 Nos. 63 Amps FP MCB (36KA)

Auditorium Block Panels Same as above description, but following mountings INCOMER:- 1 Nos. 630 Amps. 4P MCCB (50 KA) with electronic releases. 1 Set phase indication lights (R, Y, B) 1 No. Volt Meter (digital type) with inbuilt VSS & control fuses. 1 No. 0-630 Amp. Ammeter (digital type) with inbuilt ASS BUS BARS:- 630 Amps. TP&N aluminium bus bars (50 KA) OUT GOINGS:-2 Nos. 400 Amps. TPN MCCB (36 KA) with electronic releases 2 Nos. 100 Amps. TPN MCCB (25 KA) with electronic releases 6 Nos.63 Amps. TPN MCCB (25 KA) with electronic releases.6 Nos. 40A TPN, MCB (10KA).

Type -2 BlockPanel Same as above description, but following mountings INCOMER:-1 Nos. 250 Amps. 4P MCCB (36 KA) with thermal releases. 1 Set phase indication lights (R, Y, B) 1 No. Volt Meter (digital type) with inbuilt VSS & control fuses. 1 No. 0-250 Amp. Ammeter (digital type) with inbuilt ASS BUS BARS:- 125 Amps. TP&N aluminium bus bars (36 KA) OUT GOINGS:- 1 No. 63 amp. FP MCB (10 KA) 18 No. 40 amp. MCB DP (10KA) 18 No. Space for Energy Meter 1 Phase 1 Nos. 32 Amp. FP, MCB (10KA)

Type-3 Block Same as above description, but following mountings 1 Nos. 250 Amps. 4P MCCB (25 KA) with electronic releases. 1 Set phase indication lights (R, Y, B) 1 No. Volt Meter (digital type) with inbuilt VSS & control fuses. 1 No. 0-250 Amp. Ammeter (digital type) with inbuilt ASS BUS BARS:- 320 Amps. TP&N aluminium bus bars (25 KA) OUT GOINGS:- 1 Nos. 63 amp. FP MCCB (16 KA) (For Lift) 26 Nos. 40 amp. FP MCB (10KA) 26 Nos. Space for Meter 1 Nos. 32 Amp. FP, MCB (10KA) (For Common Area Lighting)

Type-4 Block Same as above description, but following mountings INCOMER:- 1 Nos. 400 Amps. 4P MCCB (36 KA) with thermal releases. 1 Set phase indication lights (R, Y, B) 1 No. Volt Meter (digital type) with inbuilt VSS & control fuses. 1 No. 0-800 Amp. Ammeter (digital type) with inbuilt ASS BUS BARS:- 500 Amps. TP&N aluminium bus bars (36 KA) OUT GOINGS:- 1 No. 63 amp FP MCCB (16KA) (For Lift) 28 No. 63 amp. FP MCB(10KA) 22 Nos. Space for Meter

Type-5 Block Same as above description, but following mountings 1 Nos. 250 Amps. 4P MCCB (36KA) with electronic releases. 1 Set phase indication lights (R, Y, B) 1 No. Volt Meter (digital type) with inbuilt VSS & control fuses. 1 No. 0-250 Amp. Ammeter (digital type) with inbuilt ASS BUS BARS:- 320 Amps. TP&N aluminium bus bars (25 KA) OUT GOINGS:- 2 Nos. 63 amp. FP MCCB (16 KA) (For Lift) 8 Nos. 63 amp. FP MCB (10KA) 10 Nos. Space for Meter 1 Nos. 40Amp. FP, MCB (10KA) (For Common Area Lighting)

Boys Hostel Panels Same as above description, but following mountings INCOMER:- 1 Nos. 400 Amps. 4P MCCB (36 KA) with electronic releases. 1 Set phase indication lights (R, Y, B) 1 No. Volt Meter (digital type) with inbuilt VSS & control fuses. 1 No. 0-250 Amp. Ammeter (digital type) with inbuilt ASS BUS BARS:- 500 Amps. TP&N aluminium bus bars (25 KA) OUT GOINGS:- 1 Nos. 100 Amps. FP MCCB (25KA) 18 Nos. 40A TPN, MCB (16KA). 1 Nos. 32 Amp. FP, MCB (10KA)

Girls Hostel Panels Same as above description, but following mountings INCOMER:- 1 Nos. 250 Amps. 4P MCCB (36 KA) with electronic releases. 1 Set phase indication lights (R, Y, B) 1 No. Volt Meter (digital type) with inbuilt VSS & control fuses. 1 No. 0-250 Amp. Ammeter (digital type) with inbuilt ASS BUS BARS:- 320 Amps. TP&N aluminium bus bars (36 KA) OUT GOINGS:- 1 Nos. 100 Amps. FP MCCB (25KA)18 Nos. 40A TPN, MCB (16KA). 1 Nos. 32 Amp. FP, MCB (10KA)

Intern Male Hostel Panels Same as above description, but following mountings INCOMER:- 1 Nos. 200 Amps. 4P MCCB (36 KA) with electronic releases. 1 Set phase indication lights (R, Y, B) 1 No. Volt Meter (digital type) with inbuilt VSS & control fuses. 1 No. 0-250 Amp. Ammeter (digital type) with inbuilt ASS BUS BARS:- 320 Amps. TP&N aluminium bus bars (36 KA) OUT GOINGS:- 10 Nos. 63A TPN, MCB (16KA). 1 Nos. 40 Amp. FP, MCB (10KA)

Intern Female Hostel Same as above description, but following mountings INCOMER:- 1 Nos. 200 Amps. 4P MCCB (36 KA) with electronic releases. 1 Set phase indication lights (R, Y, B) 1 No. Volt Meter (digital type) with inbuilt VSS & control fuses. 1 No. 0-250 Amp. Ammeter (digital type) with inbuilt ASS BUS BARS:- 320 Amps. TP&N aluminium bus bars (36 KA)OUT GOINGS:- 10 Nos. 63A TPN, MCB (16KA). 1 Nos. 40 Amp. FP, MCB (10KA)

Sr jr Residence Hostel Same as above description, but following mountings INCOMER:- 1 Nos.400 Amps. 4P MCCB (36 KA) with electronic releases. 1 Set phase indication lights (R, Y, B) 1 No. Volt Meter (digital type) with inbuilt VSS & control fuses. 1 No. 0-250 Amp. Ammeter (digital type) with inbuilt ASS BUS BARS:- 600 Amps. TP&N aluminium bus bars (36 KA) OUT GOINGS:- 2 Nos. 100 Amps. FP MCCB (25KA) 12 Nos. 125A TPN, MCCB (25KA). 1 Nos. 32 Amp. FP, MCB (10KA)

Nurse Hostel Same as above description, but following mountings INCOMER:- 1 Nos. 400 Amps. 4P MCCB (36 KA) with electronic releases. 1 Set phase indication lights (R, Y, B)1 No. Volt Meter (digital type) with inbuilt VSS & control fuses. 1 No. 0-250 Amp. Ammeter (digital type) with inbuilt ASS BUS BARS:- 600 Amps. TP&N aluminium bus bars (36 KA) OUT GOINGS:- 1 Nos. 100 Amps. FP MCCB (25KA) 8 Nos. 63A TPN, MCB (16KA). 1 Nos. 32 Amp. FP, MCB (10KA)

Dinning Block Panel Same as above description, but following mountings 1 Nos. 315 Amps. 4P MCCB (36 KA) with electronic releases. 1 Set phase indication lights (R, Y, B) 1 No. Volt Meter (digital type) with inbuilt VSS & control fuses. 1 No. 0-315 Amp. Ammeter (digital type) with inbuilt ASS BUS BARS:- 350 Amps. TP&N aluminium bus bars (25 KA) OUT GOINGS:- 1 Nos. 250 Amps. TPN MCCB (36 KA) with electronic releases 2 Nos. 100 Amps. TPN MCCB (25 KA) with electronic releases 4 Nos.63 Amps. TPN MCCB (25 KA) with electronic releases. 6 Nos. 40A TPN, MCB (10KA).

Patient Relative INCOMER:- 1 Nos. 200 Amps. 4P MCCB (36 KA) with electronic releases. 1 Set phase indication lights (R, Y, B) 1 No. Volt Meter (digital type) with inbuilt VSS & control fuses. 1 No. 0-250 Amp. Ammeter (digital type) with inbuilt ASS BUS BARS:- 320 Amps. TP&N aluminium bus bars (25 KA) OUT GOINGS:- 6 Nos. 63A TPN, MCB (16KA). 6 Nos. 40 Amp. DP, MCB (10KA)

Supplying, installing by suspension on ceiling, testing and commissioning of following capacity Sandwich Type Rising Mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply with metal clad enclosure having IP-54 rating after fixing the tap off boxes and all accessories, made of 1.6mm thick steel sheet duly powder coated in convenient sections complete with 4 Nos aluminium bus bars having current density of 130 A/ sq cm at nominal current rating, necessary joints, elbow joints & expansion joints and bends, fire barrier at each floor, provision of tapping at every metre, adopter box and copper flexible for joints, continuous earthing with 2 Nos aluminium strip of suitable size (one on each side) including, G.I. clamping brackets, suspenders, angle iron bracket, steel fasteners, connecting to earthing system etc. as required 1600 amps 70KA SC for 1 sec

800 amps 50KA SC for 1 sec

Supplying, installation, testing & commisioning of following capacity Plug In/ tap off box on the existing Compact Type bus trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick sheet steel enclosure (IP54) duly powder coated with provision of MCCB/ACB (but without MCCB/ACB) complete etc. as required 125/100A Tap-off Box with inbuilt Disconnection (Legrand/ C&S or equivalent as approved by the Deptt.) on Cover ( W/0 MCCB/HRC fuse)

200/160A Tap-off Box with inbuilt Disconnection (Legrand/ C&S or equivalent as approved by the Deptt.) on Cover ( W/0 MCCB/HRC fuse)

250A Tap-off Box with inbuilt Disconnection (Legrand/ C&S or equivalent as approved by the Deptt.) on Cover ( W/0 MCCB/HRC fuse)

400/ 630A Tap-off Box with inbuilt Disconnection (Legrand/ C&S or equivalent as approved by the Deptt.) on Cover ( W/0 MCCB/HRC fuse)

Supplying, installation, testing & commisioning of following capacity End Feed Unit for the existing Air Insulated Compact Type bus trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick steel sheet enclosure (IP54) duly powder coated with provision of MCCB/ACB (but without MCCB/ACB) complete with necessary joints including clamping brackets, angle iron bracket, steel fasteners, connecting to earthing system etc. as required 800 Amps 50 KA TPN ACB EDO

1600 Amps 50 KA TPN ACB EDO

Supplying, installation, testing and commissioning of following ratings of MCCBs installed in sheet steel enclosure with indicating lamps etc., earthing, connections, as per specifications complete as required. 63 Amps 25 KA FP MCCB

100 Amps 25 KA FP MCCB

125 Amps 25 KA FP MCCB

160 Amps 25 KA FP MCCB

250 Amps 36 KA FP MCCB

400 Amps 36 KA FP MCCB

Supplying, installation, testing and commissioning of following ratings of ACB installed in sheet steel enclosure with indicating lamps etc., earthing, connections, as per specifications complete as required. 800 Amps 50 KA FP ACB EDO

1600 Amps 70 KA FP ACB EDO

Supplying, installation, testing and commissioning of following ratings of automatic transfer switch installed in sheet steel enclosure with indicating lamps etc., earthing, connections, as per specifications complete as required. 800 Amps 50 KA FP Automatic Transfer Switch

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

L.T. CABLES Supplying following 1.1kV grade, XLPE insulated, heavy duty armoured cables suitable for 415V, 50Hz, AC system, with inner and outer PVC sheath, galvanised steel armouring and with all components as mentioned in BOQ, specifications, complete as required. 3.5 x 400 sq.mm

3.5 x 300 sq.mm

3.5 x 240 sq.mm

3.5 x 185 sq.mm

3.5 x 150 sq.mm

3.5 x 120 sq.mm

3.5 x 95 sq.mm

3.5 x 70 sq.mm

3.5 x 50 sq.mm

3.5 x 35 sq.mm

4 x 16 sq.mm

4 x 10 sq.mm

4 x 6 sq.mm

2 x 6 sq.mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required. Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size in the existing RCC/ HUME/ METAL pipe as required. Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size in the existing masonry open duct as required. Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size on cable tray as required. Upto 35 sq. mm (clamped with 1mm thick saddle)

Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)

Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 3½ X 300 sq. mm

3½ X 240 sq. mm

3½ X 185 sq. mm

3½ X 150 sq. mm

3.5C X 120 Sqmm

3.5C X 95 Sqmm

3.5C X70 Sqmm

3.5C X50 Sqmm

3.5C X35 Sqmm

3.5C X25 Sqmm

4C X 16 Sqmm

4C X 10/6 Sqmm

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required. 100mm dia

250mm dia

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. 90 mm dia (OD-90 mm & ID-76 mm nominal)

120 mm dia (OD-120 mm & ID-103 mm nominal)

Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required 80 mm dia

100 mm dia

Steel work in built up tubular (round ,square or rectangle hollow tubes etc) trusses etc .including cutting,hosting ,fixing in position and aplying a priming coate of approved steel primer including welding and bolted with special shaped washer etc as complete.

Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 150mm wide 50 mm depth

300mm wide 62.5mm depth

450mm wide 62.5mm depth

600mm wide 75mm depth

900mm wide 75mm depth

Supply, laying, connecting, termination and testing of under noted sizes of flexible copper conductor flexible PVC sheathed & sleeved and overall PVC sleeved 1.1 KV grade power distribution cables conforming to relevant IS code and as per specification in ground (in existing trenches) through pipe or on wall / racks cable trays including dressing and clamping the cable with MS zinc passivated clamps etc. as required. 1 C x 70 sq.mm

1 C x 35 sq.mm

4 C x 25 sq.mm

4 C x 35 sq.mm

4 C x 50 sq.mm

EARTHING Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

LIGHTNING PROTECTION SYSTEM Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or on surface of wall for lightning conductor complete as required. (For vertical run)

Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 Nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.

UPS SYSTEM Supply, installation, testing & commissioning of the following: IGBT based 100 KVA parallel True Online Double Conversion UPS suitable for unbalanced, 3 Phase input and 3 phase 415 V output UPS system with isolation transformer (i.e., K-13 type), suitable for operating in parallel and each comprising as per technical specification complete as required. VRLA sealed maintenance free batteries for 100 KVA UPS system, for providing 30 minutes back up to each 100 KVA UPS. Each bank of batteries shall comprise required Nos. of SMF batteries etc as per specifications as required. Matching cabinet to house SMF batteries for 100 KVA UPS system along with interconnecting links and I/c S/F MCCB as required.

Supply, installation, testing & commissioning of the following: IGBT based 80 KVA parallel True Online Double Conversion UPS suitable for unbalanced, 3 Phase input and 3 phase 415 V output UPS system with isolation transformer (i.e., K-13 type), suitable for operating in parallel and each comprising as per technical specification complete as required. VRLA sealed maintenance free batteries for 80 KVA UPS system, for providing 30 minutes back up to each 80 KVA UPS. Each bank of batteries shall comprise required Nos. of SMF batteries etc as per specifications as required. Matching cabinet to house SMF batteries for 80 KVA UPS system along with interconnecting links and I/c S/F MCCB as required.

Supply, installation, testing & commissioning of the following: IGBT based 40 KVA parallel True Online Double Conversion UPS suitable for unbalanced, 3 Phase input and 3 phase 415 V output UPS system with isolation transformer (i.e., K-13 type), suitable for operating in parallel and each comprising as per technical specification complete as required. VRLA sealed maintenance free batteries for 40 KVA UPS system, for providing 30 minutes back up to each 40 KVA UPS. Each bank of batteries shall comprise required Nos. of SMF batteries etc as per specifications as required. Matching cabinet to house SMF batteries for 40 KVA UPS system along with interconnecting links and I/c S/F MCCB as required.

Supply, installation, testing & commissioning of the following: IGBT based 20 KVA parallel True Online Double Conversion UPS suitable for unbalanced, 3 Phase input and 3 phase 415 V output UPS system with isolation transformer (i.e., K-13 type), suitable for operating in parallel and each comprising as per technical specification complete as required. VRLA sealed maintenance free batteries for 20 KVA UPS system, for providing 30 minutes back up to each 20 KVA UPS. Each bank of batteries shall comprise required Nos. of SMF batteries etc as per specifications as required. Matching cabinet to house SMF batteries for 20 KVA UPS system along with interconnecting links and I/c S/F MCCB as required.

Supply, installation, testing & commissioning of the following: IGBT based 10 KVA parallel True Online Double Conversion UPS suitable for unbalanced, 3 Phase input and 3 phase 415 V output UPS system with isolation transformer (i.e., K-13 type), suitable for operating in parallel and each comprising as per technical specification complete as required. VRLA sealed maintenance free batteries for 10 KVA UPS system, for providing 30 minutes back up to each 10 KVA UPS. Each bank of batteries shall comprise required Nos. of SMF batteries etc as per specifications as required. Matching cabinet to house SMF batteries for 10 KVA UPS system along with interconnecting links and I/c S/F MCCB as required.

Two Loop Panel.

Supplying, installation, testing & commissioning of central graphical fire alarm management system to centrally monitor and operate the fire alarm system complete as required.

Supplying, installation, testing & commissioning of repeater panel wih 320 character/ Touch screen LCD display with inbuilt reset, acknowledge and silence switches complete as required.

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required.

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required.

Supplying, installation, testing & commisssioning of intelligent addressable programmable sounder complete as required.

Supplying, installation, testing & commissioning of fault isolator complete with base as required.

Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed tempreature thermistor complete with base as required.

Supplying, installation, testing & commissioning of addressable fire control module complete as required.(For automatic door closers, elevator controls, fire suppression systems, smoke ejectors etc)

Supplying, installation, testing & commissioning of addressable fire monitor module complete as required.

Supplying, installation, testing & commissioning of addressable phone control module complete as required.

Supplying, installation, testing & commissioning of addressable beam detector with short circuit isolator (inbuilt or seperate) complete with emitter and receiver including connections with remote test features etc complete as required.

Supplying, installation, testing & commissioning of intelligent addressable duct detector including suitable Photo detector complete with base as required.

Supplying, installation, testing & commissioning of addressable manual call point complete as required.

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required.

Supplying, installation, testing & commissioning of fire fighter telephone handset complete as required.

Supplying, installation, testing & commissioning of fire fighter phone jack complete as required.

PUBLIC ADDRESS SYSTEM Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation complete as required.

Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker complete as required.

Supplying, installation, testing & commissioning of 1.5/3/6W metal box ceiling/wall speakers complete as required.

Supplying, installation, testing & commissioning of ceiling/wall mounted loud speaker, 3/1.5 Watt in ABS enclosure complete as required.

Supplying, installation, testing & commissioning of 6 inches dia, 2 watts, 70/100 volts ceiling speaker complete as required.

Supplying, installation, testing & commissioning of digital audio amplifier 75 Watt, 25V rms operating at 240 Volt AC Supply complete as required.

Supplying, installation, testing & commissioning of Voice command keypad 6 zone, with microphone assembly complete as required.

Cabling and Wiring Supplying & laying of 2x1.5 sqmm fire survival armoured cable, 600/1000V rated with annealed copper conductor having glass mica fire barrier tape covered by an extruded layer of Cross Linkable Ethylene Propylene Rubber (EPR) insulation and LSZH inner bedding, steel wire armouring & LSZH outer sheath complete as required.

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required.

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required. speaker cable Single pair, 2-core, 1.5 sqmm

Supplying and fixing 25 mm dia MS flexible pipe with PVC coating along with all ancillaries and accessories like coupler etc. as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25mm dia conduit

32mm dia conduit

ELV System IP CCTV System & Access Control System SITC of IP Dome Camera 4MP IR Dome Camera, Metal Housing, H.265+/H.265/H.264, Up to 2592x1520@25fps, Min. illumination Color: [email protected], Smart IR, IR Range: 30m, Built-in Mic, SD Card Slot, Reset Button, POE, IP67, IK10, 120dB WDR, Support tripwire and perimeter, ANR. BIS,CE,FCC,ROHS,UL/EN. etc all complete. Make: Pelco / Royalshield / Bosch / Axis

SITC of IP Bullet Camera 4MP IR Bullet Camera, Metal Housing, H.265+/H.265/H.264, Up to 2592x1520@25fps, Smart IR, IR Range: 50m, Built-in Mic, SD Card Slot, Reset Button, 120dB WDR, POE, IP67, 120dB WDR, Support tripwire and perimeter, ANR. BIS,CE,FCC,ROHS,UL/ENetc all complete. Make: Pelco / Royalshield / Bosch / Axis or equivalent

SITC of IP PTZ Camera 2 MP -IP PTZ Camera 2 MP - IP Network 1/2.8" CMOS, Dual IR Cut Filter , 1920x1080:30fps, H.264/MJPEG Or better, Triple streams, AC24V/POE+, IP66, Micro SD card slot support up to 128GB, Alarm in/out 1/1, Audio in/out 1/1, -30-65℃, IP66, 33x optical zoom(4.6 ~ 152mm), IR range: up to 150m, 120dB WDR, IP66, 33X optical zoom, HLC,BLC,3D DNR, Smart functions-Auto Tracking, CE, FCC, Defog, Privacy mask, Up to 8 Pattern, Presets – 300 , PAN Range - 360° , 0.1°/s ~ 180°/s ,Tilt Range -–16° ~ 90° (auto flip) , 0.1° ~ 120°/s etc all complete. Certificate – BIS, CE, FCC, ROHS, UL/EN etc all complete. Make: Pelco / Royalshield / Bosch / Axis or equivalent

SITC of NVR - H.265 8SATA 64ch NVR, H.265+ Compression, Support 64-ch input, Up to 12MP Resolution Recording, Incoming Bandwidth 320Mbps, Outgoing Bandwidth 320Mbps, HDMI and VGA independent outputs, HDMI Video output at up to 4K (3840 × 2160) resolution, 8 SATA interfaces for 8 HDDs, up to 10TB for each HDD, eSATA interface:- 1 SATA interface, 2xRJ45 self-adaptive 10/100/1000 Mbps network interfaces, VCA detection alarm is supported, Array Type:- JBOD, RAID0/1/5/6/10, 2xUSB 2.0, 1xUSB 3.0, serial Interface:- 2xRS-485, 1xRS-232, No.of Hard Disks 4TB for the calaculation of 1 month recording 2MP@25FPS as per all camera count, VMS should also be included if required etc. all complete. Make: Pelco / Royalshield / Bosch / Axis or equivalent

SITC of MS Windows 2008 Server R2 x64, Intel i5 Xeon Quad Core processor, 8 GB RAM, 1TB HDD, 2GB Graphics Card. With CD/DVD player, Mouse and Keyboard etc all complete. Make: HP / Dell or equivalent

SITC of 55" LCD narrow Bazel for Monitoring for each NVR Server etc. all complete. Make: Sony / Panasonic / Aaztec or equivalent

Access Control System Supply Installation Testing and Commissioning of Web Based Standard Application for Time Attendance-Access Control, GUI, Antipass back, Reports in Inbox, with Unlimited Users, Door Scheduling, Unlimited Client logins, Event Notification, POP ups, Mustur Points, Area Control, Time base access and alerts. Software should be VAPT approved and should provide Per reader license, Should have integrated modules of Elevator management, Visitor Management, Template management and card priting module , Integrated credential issuance application inclusive of card template designing, card printing, finger print enrollment, key management, contactless card reader/writer & contact card reader/writer Approved Make: IDCUBE-MERCURY/MAXXESS/MORPHO/DDS or equivalent

Supply Installation Testing and Commissioning of Visitor Managment Software Application to allow employees to pre- register visitors & visitor request approval management Approved Make: IDCUBE-MERCURY/MAXXESS/MORPHO/DDS or equivalent

Supply Installation Testing and Commissioning of IP Based Master controller with 2,40,000 Card holder capacity, 50,000 event buffer. Natively supports 4 readers and 2 openings over OSDP and expandable upto 64 readers with IP Based interface module. UL294 Listed,FCC, CE, RoHS, NIST Certified Encryption. Approved Make: IDCUBE-MERCURY/MAXXESS/MORPHO or equivalent

Supply Installation Testing and Commissioning of IP based Reader Interface module. Supports 2 Door- 2 reader over weigend and 2 Door- 4 Reader over OSDP. Also works with PoE & PoE+ . UL294 Listed, FCC, CE, RoHS, NIST Certified Encryption. Approved Make: IDCUBE-MERCURY/ MAXXESS/ MORPHO or equivalent

Supply Installation Testing and Commissioning of Enclosure with UL Listed Power Supply for Controllers. Approved Make: IDCUBE-MERCURY/ MAXXESS/ MORPHO/ DDS or equivalent

Supply Installation Testing and Commissioning of Iclass Smart card reader1. Operating Frequency: 13.56 MHz Contactless Smart Card Reader Data Formats: Wigand, OSDP, Keypad Data Formats : Field configurable, 8-Bit Burst (default) and 26-Bit Wiegand, Certifications and Compliance: UL294/cUL (US), FCC, IC, CE,C-Tick, MIC, NCC Housing Material UL94 Polycarbonate. Approved Make: IDCUBE-MERCURY/ MAXXESS/ MORPHO/ DDS/ HID or equivalent

Supply Installation Testing and Commissioning of UL294 Listed Biometric device with inbuilt smart card reader CPU: ARM® Cortex™-A9 core 1GHz • Linux Operating System, Fake finger detection • Duress finger • FBI PIV IQS certified optical fingerprint senso. • Network/Communication: - Ethernet, RS485, USB,Integrated Smart Card Reader, Internal storage capacity: 512MB Flash, 512MB RAM, Operating conditions: - Temperature: -20°C to 55°C (-4°F to 131°F) - Humidity: 10% to 80% (non condensing). • Ingress protection: IP65 and • EMC/Safety standards: - CE, CB, FCC, BIS, UL294 , RoHS, REACh and WEEE compliant. Approved Make: IDCUBE-MERCURY/MAXXESS/MORPHO/HID or equivalent

Supply, Installation, Testing & Commissioning of Smart card Frequency Excitation (13.56 MHz) Mifare/I-class technology smart Card. Memory Type EEPROM,Complies with ISO/IEC standards for thickness. Lifetime Warranty Approved Make: IDCUBE-MERCURY/MAXXESS/MORPHO/HID or equivalent

Supply Installation Testing and Commissioning of Single Door Electro Magnetic Lock Approved,Monitored Single Leaf/Double Leaf Electromagnetic Lock with 600/1200 lbs holding force with dual Monitoring and tested for 45 min on fire door assemblies fire rating including necessary mounting brackets Standards: UL Listed or CE Certified. Make: ASSA ABLOY/Trimec/Von Duprin or equivalent

Supply Installation Testing and Commissioning of Double Door Electro Magnetic Lock Approved,Monitored Single Leaf/Double Leaf Electromagnetic Lock with 600/1200 lbs holding force with dual Monitoring and tested for 45 min on fire door assemblies fire rating including necessary mounting brackets Standards: UL Listed or CE Certified . Make: ASSA ABLOY/Trimec/Von Duprin or equivalent

Supply Installation Testing and Commissioning Touchless Request to Exit button with detection range from 4 to 12 cm , 0.1 million cycle tested , Make: ASSA ABLOY/Trimec/Von Duprin or equivalent

Supply Installation Testing and Commissioning Emergency Door Release Button, Gree, Key Resettable, Double Pole Double Throw (DPDT), Make: ASSA ABLOY/Trimec/Von Duprin or equivalent

Supply, Installation, Testing & Commissioning of Parking Management & Control System: Motorised Boom Barrier: Electromechanical Boom Barrier of 6 Mtr Boom Length, Opening Closing Time 2.0 Sec ( adjustable) I.P. 54, MTBF 2 Million etc. all complete, CE Certified.etc. all complete. Make- Somfy / IRAM/ Neptune or equivalent

Supply, Installation, Testing & Commissioning of Parking Management & Control System: Long Range UHF RFID Reader, Wiegand Interface, Read Range >10 Meter, EPC C-1, Gen-2 Integrated Antenna, etc. all complete. Make- Somfy / IRAM/ Neptune or equivalent

Supply, Installation, Testing & Commissioning of UHF Windshield Tag for vehicle etc. all complete. Make- Somfy / IRAM/ Neptune/ Standard or equivalent

Supply Installation Testing and Commissioning of Network Cat6A cable ( Complete Roll 305 Mtr aoorox) Approved Make: 3C3 / Corning / Panduit or equivalent

Supply Installation Testing and Commissioning of 2-conductor 4 core 20 to 22 AWG Approved Make: FINOLEX / EXCEL / DELTON/POLYCAB or equivalent

Supply Installation Testing and Commissioning of RS485 2 twisted pair, individually shielded, 18 to 22 AWG Approved Make: FINOLEX / EXCEL / DELTON/POLYCAB or equivalent

Supply Installation Testing and Commissioning of Power Cable 3*1.5 sqmm PVC insulated flexible FRLS copper Approved Make: FINOLEX / EXCEL / DELTON/POLYCAB or equivalent

IT Active Passive, Wi-Fi & IPEBAX System Supply, Installation, Testing & Commissioning of Cat-6A Mounting Cords 7 Feet for Data as per given Specification etc. all complete. Make: 3C3/ Corning / Panduit/ Actassi or equivalent

Supply, Installation, Testing & Commissioning of Cat-6A Mounting Cords 4 Feet for Data Jack Panel end as per given Specification etc. all complete. Make: 3C3/ Corning / Panduit/ Actassi or equivalent

Supply, Installation, Testing & Commissioning of Cat-6A, 24 Port Jack Panel for data as per given Specification etc. all complete. Make: 3C3/ Corning / Panduit/ Actassi or equivalent

Supply, Installation, Testing & Commissioning of Cat-6A Mounting Cords 4 Feet for Voice Jack Panel end as per given Specification etc. all complete. Make: 3C3/ Corning / Panduit/ Actassi or equivalent

Supply, Installation, Testing & Commissioning of Cat-6A 24 Port Jack Panel for Voice Field as per given Specification etc. all complete. Make: 3C3/ Corning / Panduit/ Actassi

Supply, Installation, Testing & Commissioning of Cat-6A 24 Port Jack Panel for Voice Field & Resource as per given Specification etc. all complete. Make: 3C3/ Corning / Panduit/ Actassi or equivalent

Supply, Installation, Testing & Commissioning of 15 U Wall Mount Rack as per given Specification etc. all complete. Make: Rittal / Valrack/ APW / Netrack or equivalent

Supply, Installation, Testing & Commissioning of 1 U PVC Cable Manager as per given Specification etc. all complete. Make: Rittal / Valrack/ President / Netrack or equivalent

Supply, Installation, Testing & Commissioning of 6 socket PDU as per given Specification etc. all complete. Make: Rittal / Valrack/ APW/ Netrack or equivalent

Supply, Installation, Testing & Commissioning of Mounting Hardware pack of 10pcs as per given Specification etc. all complete. Make: Rittal / Valrack/ APW/ Netrack or equivalent

Supply, Installation, Testing & Commissioning of 600 Pair MDF Box with Mounting Frame as per given Specification etc. all complete. Make: NetRack / Krone / APW / Actassi

Supply, Installation, Testing & Commissioning of 10 Pair Krone Module as per given Specification etc. all complete. Make: NetRack / Krone / APW / Actassi or equivalent

Supply, Installation, Testing & Commissioning of 300 Pair MDF Box with Mounting Frame as per given Specification etc. all complete. Make: NetRack / Krone / APW / Actassi

Supply, Installation, Testing & Commissioning of 200 Pair MDF Box with Mounting Frame as per given Specification etc. all complete. Make: NetRack / Krone / APW / Actassi

Supply, Installation, Testing & Commissioning of 25 Pair Riser cable as per given Specification etc. all complete. Make: Delton / Skyton / Actassi or equivalent

Supply, Installation, Testing & Commissioning of 42 U Wall Mount Rack as per given Specification etc. all complete. Make: Rittal / Valrack/ APW/ Netrack or equivalent

Supply, Installation, Testing & Commissioning of DK PS Frame,1000Wx2000Hx1200D (2nos. of 1000Wx2000Hx600D with Baying tube), Top cover with rear fixed & slideable gland plate with foam insert for cable entry, bottom cover with standard gland plates with foam insert for cable entry and rear 4nos. of 50mm dia rubber grommets as per std., 2 pairs of 42U 19" L - type angles & special assembly kit for mounting 19" angles & punched sections, Complete with 11 KVA Power and 7TR Cooling in complete. It consist of in built Temperature, Humidity, Automatic door opening & leakage Monitoring System. with Signal Pillar Fire Extinguisher System as per given Specification etc. all complete. Make: Rittal / Valrack/ APW / Netrack or equivalent

Supply, Installation, Testing & Commissioning of 6 Core Single Mode Fiber ( Armored) Cable as per given Specification etc. all complete. Make: 3C3/ Corning / Panduit/ Actassi or equivalent

Supply, Installation, Testing & Commissioning of 12 Port Fiber LIU Loaded with SC SM Coupler, as per given Specification etc. all complete. Make: 3C3/ Corning / Panduit/ Actassi or equivalent

Supply, Installation, Testing & Commissioning of SC SM Pigtail (1.0 Mtr) as per given Specification etc. all complete. Make: 3C3/ Corning / Panduit/ Actassi or equivalent

Supply, Installation, Testing & Commissioning of SC-LC SM Fiber Patch Cords ( 3 Mtr) as per given Specification etc. all complete. Make: 3C3/ Corning / Panduit/ Actassi or equivalent

Supply, Installation, Testing & Commissioning of 6 Core Multi Mode Fiber ( Armored) Cable as per given Specification etc. all complete. Make: 3C3/ Corning / Panduit/ Actassi

Supply, Installation, Testing & Commissioning of 12 Port Fiber LIU Loaded with SC MM Coupler, as per given Specification etc. all complete. Make: 3C3/ Corning / Panduit/ Actassi or equivalent

Supply, Installation, Testing & Commissioning of SC MM Pigtail (1.0 Mtr) as per given Specification etc. all complete. Make: 3C3/ Corning / Panduit/ Actassi or equivalent

Supply, Installation, Testing & Commissioning of Blank Panel for LIU as per given Specification etc. all complete. Make: 3C3/ Corning / Panduit/ Actassi or equivalent

Supply, Installation, Testing & Commissioning of SC MM Pigtail (1.0 Mtr) as per given Specification etc. all complete.

Supply, Installation, Testing & Commissioning of 2 port faceplate with Gang Box etc. all complete. Make: 3C3/ Corning / Panduit/ Actassi or equivalent

Supply, Installation, Testing & Commissioning of LSZH Cat 6A-10G speed unshielded twisted pair computer cable with 23 AWG solid copper conductors in existing concealed/surface conduits/Raceways complete 305 Mtr. Roll as per specification etc. all complete. Make: 3C3/ Corning / Panduit/ Actassi or equivalent

Supply, Installation, Testing & Commissioning of UTP Cat-6A Information Outlet Red for Data as per specification etc. all complete Make: 3C3/ Corning / Panduit/ Actassi

Supply, Installation, Testing & Commissioning of UTP Cat-6A Information Outlet Yellow for Voice as per specification etc. all complete. Make: 3C3/ Corning / Panduit/ Actassi or equivalent

Supply, Installation, Testing & Commissioning of Core Switch with Chassis Based as per the given Specification etc. all complete. Make- Cisco / Juniper / Allied Telesis or equivalent

Supply, Installation, Testing & Commissioning of Layer 3 Distribution Switch as per the given Specification etc. all complete. Make- Cisco / Juniper / Allied Telesis or equivalent

Supply, Installation, Testing & Commissioning of Wireless LAN Controller which can control up to 250 APs as per the given Specification etc. all complete. Make- Cisco / Juniper / Allied Telesis or equivalent

Supply, Installation, Testing & Commissioning of Layer 2 Switch 48 Port as per the given Specification etc. all complete. Make- Cisco / Juniper / Allied Telesis or equivalent

Supply, Installation, Testing & Commissioning of Layer 2 Switch 24port as per the given Specification etc. all complete. Make- Cisco / Juniper / Allied Telesis or equivalent

Supply, Installation, Testing & Commissioning of Access point which can support the given Controller as per the given Specification etc. all complete. Make- Cisco / Juniper / Allied Telesis or equivalent

Supply, Installation, Testing & Commissioning of Internet Firewall Firewall I/O 10/100/1000 , Gigabit SFP (8throughput), (HTTP/appmix) 2.1/2.1 Gbps , Threat Prevention throughput (HTTP/appmix) 1.0/1.2 Gbps , IPsec VPN throughput 1.6 Gbps , New sessions per second 13,000 , Max sessions 192,000 , 802.1Q VLAN tags per device/per interface: 4,094/4,094 Aggregate interfaces (802.3ad), LACP , NAT modes (IPv4): static IP, dynamic IP, dynamic IP and port (port address translation) , NAT64, NPTv6 , Modes: active/active, active/passive Failure detection: path monitoring, interface monitoring , Zero Touch Provisioning (ZTP)etc. all complete. Make- Extreme / Palo Alto/ Allied Telesis or equivalent

Supply, Installation, Testing & Commissioning of Internet Router which can support the Fiber Line as per the given Specification etc. all complete. Make- Cisco / Juniper / Allied Telesis or equivalent

Supply, Installation, Testing & Commissioning of 100% Non Blocking Fully Digital Integrated Services Digital Network (ISDN) Compatible Voice Over Internet Telephone(VoIP) ready 19" Rack mountable EPABX presently equiped with 06 ISDN PRI Trunk Lines (180 Channel), 32 IP Extension, 64 Digital Extension, 1200 Analogue Extension, Expandable up to 2000 Ports / Channels and other as per the given Specification etc. all complete. Make: Panasonic / Avaya / Alcatel Lucent/ Cisco or equivalent

Supply, Installation, Testing & Commissioning of IP User Linceses for 10 Users etc. all complete. Make: Panasonic / Avaya / Alcatel Lucent

Supply, Installation, Testing & Commissioning of 16 Port Digital Card etc. all complete. Make: Panasonic / Avaya / Alcatel Lucent or equivalent

Supply, Installation, Testing & Commissioning of 24 Port Analouge Card etc. all complete. Make: Panasonic / Avaya / Alcatel Lucent or equivalent

Supply, Installation, Testing & Commissioning of High End Digital Key Phone 6x24 Display with 24 Programmable Dual Color LED’s with 4 Feature Access Keys, multi-step Tilt angle adjustment, Navigator Key, backlit display, should have option to connect Blue Tooth etc. all complete. Make: Panasonic / Avaya / Alcatel Lucent or equivalent

Supply, Installation, Testing & Commissioning of Low end DIgital Key Phone 1x16 Display with 8 Programmable Dual Color LED’s etc. all complete. Make: Panasonic / Avaya / Alcatel Lucent or equivalent

Supply, Installation, Testing & Commissioning of IP Phone 1x16 Display with 8 Programmable Dual Color LED’s etc. all complete. Make: Panasonic / Avaya / Alcatel Lucent or equivalent

Supply, Installation, Testing & Commissioning of Analog Phone With Speaker , Small Display etc. all complete. Make: Panasonic / Avaya / Alcatel Lucent or equivalent

Hospital Management System with QMS Integration Supply, Installation, Testing & Commissioning of Design, Develop, Integration, Deployment, Implementation and Maintenance of Hospital Management System as per tender specification Hospital Management Software & hardware including QMS & other module as per detailed technical Specification with 2 year Support. HMS should have the below feature like Data from all clients will be fed into the Central System Unique ID generation of patients, Digitization of Patient work flow System will be a web based system that will be accessible to relevant stakeholders on authentication. Better follow up mechanism for patients with SMS based notification Streamlines workflow operations to improve hospital administration Enhances the quality of patient care etc all complete. Make- TCS/IICONS/ Tenwave Infotech Pvt Ltd/Cerner or equivalent

Supply, Installation, Testing & Commissioning of Minimum 16 Physical CPU Cores (Additional Virtual Cores Through Hyper-Threading Preferred) 64 GB RAM DDR4, 2 x 250 GB SSD + 5 TB 600GB SAS 10K SFF SC DS HDD+, Integrated Intel® i219- V Ethernet LAN 10/100/1000 Make- Dell/ HP or equivalent

SITC of All-in-One PC (Celeron J4005/4GB/1TB HDD/Window /Intel UHD 600 Graphics), or equivalent Thin client with Latest Browser including Printer Laser Printer -Print speed 14 PPM(ISO), Up to 600X 600X2 DPI (1200DPI), -Duty cycle 5000 pages, High Speed USB. Make- Dell/ HP or equivalent

Supply, Installation, Testing & Commissioning of SITC of 55" LED Display with built in media player with wireless connectivity etc. all complete. Make- Samsung/ Panasonic / Aaztec or equivalent

Supply, Installation, Testing & Commissioning of SITC of 13" or 15" counter display with built in media player with wireless connectivity etc. all complete. Make- Samsung/ Panasonic / Aaztec or equivalent

Supply, Installation, Testing & Commissioning of Queue management Server Software etc. all complete. Make- TCS/Aaztec / IICONS/ Tenwave Infotech Pvt Ltd/Cerner or equivalent

Supply, Installation, Testing & Commissioning of 17" touch screen , media player, thermal printer , Metal kiosk body with powder coating etc. all complete. Make- Samsung/ Panasonic / Aaztec or equivalent

Supply, Installation, Testing & Commissioning of Employee Software for calling tokens etc. all complete. Make- Tenwave / Cerner / Aaztec or equivalent

Digital Nurse Calling System Supply, Installation, Testing & Commissioning of Microprocessor based Nurse call Call station/ panel with Audible & Visual Indications necessary interfaces and regulated power supply and connections, interconnections, 16 Display Units etc. all complete. Approved Make: Aaztec/ Wipro / Process Care or equivalent

Supply, Installation, Testing & Commissioning of Microprocessor based Nurse call Call station/ panel with Audible & Visual Indications necessary interfaces and regulated power supply and connections, interconnections, 8 Display Units etc. all complete. Approved Make: Aaztec/ Wipro / Process Care or equivalent

Supply, Installation, Testing & Commissioning of Microprocessor based Bedside Call points on wall including surface / recessed metal boxes for housing the Call Points having LED indications and Push cord and having connections etc as required. With Supplying and fixing of 3 feet long Push Cord Set with Push button switch on the existing Bed side Nurse call module complete etc. all complete. Approved Make: Aaztec/ Wipro / Process Care or equivalent

Supply, Installation, Testing & Commissioning of Microprocessor based Remote Pull cord points including surface / recess mounted metal boxes for housing the Call Points having LED indications along with 6 feet long Pull cord and having stainless steel cover plate including connections etc. all complete. Approved Make: Aaztec/ Aaztec / Wipro / Process Care or equivalent

Supply, Installation, Testing & Commissioning of Corridor Dome light including surface / recessed mounted box complete with lamp & all necessary card and connector etc. including connections etc. all complete. Approved Make: Aaztec/ Wipro / Process Care or equivalent

Supply, installation, testing and commissioning of Nurse Call Processor which shall communicate to min. 6nos. Of calling units per loop and shall be be expandable with extenders upto 16 calling units. The NCP shall have voice module, call forwarding, call escallation and sms facility. The enclosure shall be made out of Aluminium. Also nurse station controller should interact with supervisory controller. should include 19" LCD Monitor as per site requirement. etc all complete. Approved Make: Aaztec/ Wipro / Process Care or equivalent

Supply, Installation, Testing & Commissioning of Supervisory Controller , which can communicate to nurse station controller, comminication device with GPS modem. The supervisory controller should have call forwarding, call escalation features. The rate shall include cost of all necessary accessories as requiredand connector etc. including connections etc. all complete. Approved Make: Aaztec/ Wipro / Process Care or equivalent

Supply, Installation, Testing & Commissioning of Nurse Call system software which can generate report like call density, average response time, record of escalated call calls profile including PC hardware with Core i7 Processor 4 GB RAM with Windows etc. including connections etc. all complete. Approved Make: Aaztec/ Wipro / Process Care or equivalent

Audio Video, Stage Lighting System Stage furnishing & Control System Display & Projection System SITC of 1DLP Laser Projector - Brightness: 10,000 ANSI lumens - Resolution: 4K UHD (3840 x 2160) Resolution - Illumination type: Laser phosphor - Contrast: 2,00,000:1 - illumination Performance: 20,000 hrs - Inputs: 2 HDMI, DisplayPort, DVI-D - Control : RS232 In, Control via HDBaseT, Ethernet - Complete with Zoom Lens etc all complete Make: Christie / Sony / NEC or equivalent

SITC of 1DLP Laser Projector - Brightness: 6,000 ANSI lumens - Resolution: WUXGA (1920 x 1200) Resolution - Illumination type: Laser phosphor - Contrast: 2,00,000:1 - illumination Performance: 20,000 hrs - Inputs: 2 HDMI, DisplayPort, DVI-D - Control : RS232 In, Control via HDBaseT, Ethernet - with Standard Lens etc all complete Make: Christie / Sony / NEC or equivalent

SITC of Tab Tensioed Motorized Projection Screen - Image Size: 240 inch diagonal - Fabric: Matt White - Aspect Ratio: 16:9 - RF Remote Control etc all complete Make: Draper/ Dalite / Aaztec or equivalent

SITC of Motorized Projection Screen - Image Size: 165 inch diagonal - Fabric: Matt White - Aspect Ratio: 16:10 - RF Remote Control etc all complete Make: Draper/ Dalite / Aaztec or equivalent

SITC of Motorized Projection Screen - Image Size: 137 inch diagonal - Fabric: Matt White - Aspect Ratio: 16:10 - RF Remote Control etc all complete Make: Draper/ Dalite / Aaztec or equivalent

SITC of Motorized Projection Screen - Image Size: 123 inch diagonal - Fabric: Matt White - Aspect Ratio: 16:10 - RF Remote Control etc all complete Make: Draper/ Dalite / Aaztec or equivalent

SITC of Motorized Projection Screen - Image Size: 109 inch diagonal - Fabric: Matt White - Aspect Ratio: 16:10 - RF Remote Control etc all complete Make: Draper/ Dalite / Aaztec or equivalent

SITC of Motorized Projection Lift - Aluminium Tubular Motorized Lift with LVC, RF remote - Max Projector size it can take : 600 x 600 x 250 ( W X D X H), - Carrying Weight Capacity : 25 kgs - Drop : 1000 mm ( 1 Mts) etc all complete Make: Draper/ Dalite / Aaztec or equivalent

SITC of Mounting arrangement for Auditorium Projector etc all complete

SITC of 86" Multi Touch Display Panel - Resolution: 4K UHD (3840 x 2160p) Resolution - Backlight : Direct-lit LED - Brightness: 410 nits - Contrast ratio: 1200:1 -Display Colors: min 10bit - integrated 10-point multi-touch capability - Input: 2 HDMI, DisplayPort, VGA, Audio In - Output- Audio output - Built-in OPS Slot - Anti Glare Treatment -HDMI-CEC - 2 x 8W speakers etc all complete Make: Christie / Sony / NEC or equivalent

SITC of 86" Display Panel - Resolution: 4K UHD (3840 x 2160p) Resolution - Backlight : Direct-lit LED - Brightness: 410 nits - Contrast ratio: 1200:1 -Display Colors: min 10bit - Input: 2 HDMI, DisplayPort, VGA, Audio In - Output- Audio output - Built-in OPS Slot - HDR10 Support -HDMI-CEC - 2 x 8W speakers etc all complete Make: Christie / Sony / NEC or equivalent

SITC of 55" Display Panel - Resolution: 4K UHD (3840 x 2160p) Resolution - Backlight : Direct-lit LED - Brightness: 500 nits - Contrast ratio: 1200:1 -Display Colors: min 10bit - Input: 2 HDMI, DisplayPort, VGA, Audio In - Output- Audio output - Built-in OPS Slot - HDR10 Support -HDMI-CEC - 2 x 8W speakers etc all complete Make: Christie / Sony / NEC or equivalent

SITC of Wall Mount kit for above display with all required accessories etc all complete

SITC of Ceiling Document Camera - Full HD 1080p Resolution - 30x optical zoom and 5x digital zoom - Signal Output: HDMI/DVI, USB - Picture by Picture - Support PC Windows 10, 8, 7, XP, Vista and Mac OSX etc all complete Make: Lumens / Wolfvision or equivalent

SITC of Desktop Document Camera - Full HD 1080p output resolution with 30fps - 20x Zoom, 12X Digital Zoom - Frame Rate: 30 fps - Built-in Back Light - Input Interface: VGA, HDMI - Output Interface: VGA x 2, HDMI, C-Video etc all complete Make: Lumens / Wolfvision or equivalent

SITC of PTZ Camera with HDMI Output and USB - 1/2.8” HD CMOS Sensor - 10x Optical Zoom - Auto & Manual Focus - HDMI Output - USB 2.0 Interface - Automatic Gain Contol - Control Protocol: VISCA - Pan Rotation: ±170° etc all complete Make: Lumens / Wolfvision / Atlona or equivalent

SITC of Desktop Hidden Connection Box, - Mechanical Locking Device, - Smooth Pneumatic Support Structure, - DisplayPort, HDMI, USB-C Network / Telephone, Power - Input voltage: 110V-220V / 50-60Hz, - Mountable Enclosure for Cables etc. all complete. Make: Altenix / Extron / Aaztec or equivalent

SITC of Dual Full HD Video Confernce System, - 1080HD PTZ camera, - Dual micpod, - Data sharing through DVI/HDMI input, - 2nd monitor support, - with remote and cables, - 1 + 3 Built In Multiparty etc all complete Make: Lifesize / Avaya / Cisco / Polycom or equivalent

SITC of Wooden lectern with wired microphone connectivity, 25" table top, with reading lamps, Cable management, Large reading surface as required with cables & connectors as required etc. all complete.

Switching System SITC of Universal Switcher with Wireless Link - Inputs: 2 HDMI, 1 DisplayPort, 1 USB-C (AV Alternate) and Native wireless AV casting - Output: Matrix 1 x HDMI, 1 x HDBaseT and Audio Out - HDMI output supports 4K/UHD @ 50 or 60Hz with 4:4:4 chroma sampling - HDBaseT output supports 4K/UHD @ 50 or 60Hz with 4:2:0 chroma subsampling - CEC Support - Room Control & Triggering Capability - Delivers true BYOD capability for a wide range of presentation sources - HDBaseT output transmits AV, control, and Ethernet up to 330 feet (100 meters) @ 1080p with CAT5e/6 or 4K/UHD using CAT6a/7 cable etc all complete Make: Atlona / Extron / Lightware or equivalent

SITC of HDBaseT Transmitter for HDMI with Audio - 4K/UHD capability @ 60 Hz with 4:2:0 chroma subsampling - HDCP 2.2 compliant - Supports 4K HDR10 - HDBaseT transmitter for HDMI, Ethernet, power, and control up to 330 feet (100 meters) - Remotely Powered via PoE (Power over Ethernet) - Multi-channel audio compliant - Transmit 4K/UHD video up to 330 feet (100 meters) with CAT6/6a/7 cable, or up to 230 feet (70 meters) using CAT5e cable Make: Atlona / Extron / Lightware or equivalent

SITC of HDBaseT Receiver for HDMI with Audio - 4K/UHD capability @ 60 Hz with 4:2:0 chroma subsampling - HDCP 2.2 compliant - HDBaseT receiver for HDMI, Ethernet, power, and control up to 330 feet (100 meters) - Local AC powering – PoE (Power over Ethernet) source - Audio De-embedding - Receive 4K/UHD video up to 330 feet (100 meters) with CAT6/6a/7 cable, or up to 295 feet (90 meters) using CAT5e cable Make: Atlona / Extron / Lightware or equivalent

SITC of HDBaseT Receiver for HDMI with USB - 4K/UHD capability @ 60 Hz with 4:2:0 chroma subsampling - HDCP 2.2 compliant - HDBaseT receiver for HDMI, Ethernet, power, control, and USB - USB 2.0 interfacing and extension up to 330 feet (100 meters) - Local or remote PoE (Power over Ethernet) powering - Receives 4K/UHD video up to 330 feet (100 meters) with CAT6/6a/7 cable, or up to 295 feet (90 meters) using CAT5e cable Make: Atlona / Extron / Lightware or equivalent

Sound System SITC of FOH Upper Arrayable loudspeaker: - Arrayable 2 way full range switchable passive/bi-amp loudspeaker - 12" LF driver or better and 1"HF compression driver or better - LF/Passive : 500 Watts rms @ 8 Ohms or better, HF :75 Watts rms power@ 6/8 Ohms or better - Frequency Range 45 Hz - 18 kHz - 60°-70° (H) x 30°- 40° (V) rotatable dispersion - Sensitivity: 96dB - Peak SPL: LF - 130dB, HF - 134dB - Birch Plywood Enclosure - Multiple Rigging Point etc. all complete Make: Music Tribe / Renkus-Heinz / Bose or equivalent

SITC of FOH Down Arrayable loudspeaker: - Arrayable 2 way full range switchable passive/bi-amp loudspeaker - 12" LF driver or better and 1"HF compression driver or better - LF/Passive : 500 Watts rms @ 8 Ohms or better, HF :75 Watts rms power@ 6/8 Ohms or better - Frequency Range 45 Hz - 18 kHz - 80°-90° (H) x 30°- 40° (V) rotatable dispersion - Sensitivity: 96dB - Peak SPL: LF - 130dB, HF - 134dB - Birch Plywood Enclosure - Multiple Rigging Point etc. all complete Make: Music Tribe / Renkus-Heinz / Bose or equivalent

SITC of Flying plate for Left, & Right Line Arrayable Speaker System etc. all complete. Make: Music Tribe / Renkus-Heinz / Bose or equivalent

SITC of Subwoofer: - Dual 12" or better Band Pass/Front loaded Subwoofer - 800 Watts rms @ 4 ohms or better - Frequency Range 35 Hz - 200 Hz - Sensitivity 100 dB - Impedance 4ohm, 8Ohm - Peak SPL,135 dB - Birch Plywood Enclosure - Multiple Rigging Point etc. all complete Make: Music Tribe / Renkus-Heinz / Bose or equivalent

SITC of Stage Front Fill: - 2 - way full range loudspeaker consisting - 8" LF or bettter ,minimum 1" HF driver - 150 W ot better continuous power handling capacity - Impedance 4/8 Ohms, - Peak SPL 119 dB - Frequency Range 60 Hz-18 kHz - Birch Plywood Enclosure - 70°-90° (H) x 50°- 70° (V)dispersion etc. all complete. Make: Music Tribe / Renkus-Heinz / Bose or equivalent

SITC of Control room/Green Room Speaker - Compact Surface Mount Coaxial Loudspeaker - 6" or better LF Driver, 0.75" or better HF driver - 60W or better power handling -90-100 degree conical dispersion - 4/6/8 Ohms, - Frequency Range 65 Hz - 18 kHz - Peak SPL 111 dB or better -UL, CE Rated - Supplied with Yoke bracket etc. all complete Make: Music Tribe / Renkus-Heinz / Bose or equivalent

SITC of Stage Monitor System - 12" LF ,1" HF Driver Coaxial Design - Rated Power 1100 Watt or better - Class-D Amplifier with inbuilt DSP - Frequency Response : 75 Hz – 18 kHz or better - Maximum SPL 125 dB peak or better - 60-80 degree Horizontal x 40-50 degree Vertical Dispersion - Fully featured user interface with LCD display for ease of navigation - Birch Plywood construction etc. all complete. Make: Music Tribe / Renkus-Heinz / Bose or equivalent

SITC of 2-Channel 2400 W Power Amplifier - Class D - Nos. of channels 2 - Power Output : 1200 W @ 4 Ohms - Integrated DSP with minimum 30 multi-slope parametric equalizers, adjustable high- and low-pass filters - Input & Output Delay, crossover with multiple filter types - Analog & AES3 Inputs - Four channel Input Mixer - THD + N 20 Hz- 20 kHz for 1 W <0.1% - Signal-to-Noise ratio >105 dB - Frequency Response 20 Hz- 20 kHz - Channel separation at 1 kHz >80 dB - Common Mode Rejection 50 dB - Software configurable limiter - Networked control - Certifictaion: CE, FCC, UL etc. all complete. Make: Music Tribe / Powersoft / D&B Audio Teknik or equivalent

SITC of 2-Channel 1200 W Power Amplifier - Class D - Nos. of channels 2 - Power Output : 600 W @ 4 Ohms - Integrated DSP with minimum 30 multi-slope parametric equalizers, adjustable high- and low-pass filters - Input & Output Delay, crossover with multiple filter types - Analog & AES3 Inputs - Four channel Input Mixer - THD + N 20 Hz- 20 kHz for 1 W <0.1% - Signal-to-Noise ratio >105 dB - Frequency Response 20 Hz- 20 kHz - Channel separation at 1 kHz >80 dB - Common Mode Rejection 50 dB - Software configurable limiter - Networked control - Certifictaion: CE, FCC, UL etc. all complete. Make: Music Tribe / Powersoft / D&B Audio Teknik or equivalent

SITC of 4 Channel 300-Watt Class D - Class D - Nos. of Channel : 4 - Delivering 4 x 60 @ 4 Ohms, In bridge 2 x 120 W @ 8 Ohms or better - THD 20Hz-20kHz at 1 W <0.5% or better - Signal-to-Noise ratio > 100dBA - Frequency Response 20 Hz- 20 kHz etc. all complete Make: Music Tribe / Powersoft / Extron or equivalent

SITC of 4" Coaxial In-Ceiling Loudspeaker - System Type: In-Ceiling Flush Mount Speaker - Driver Size: Min. 1 x 4” Driver or better - Power Continuous / Programme: 30 W / 60 W - Nominal impedance: 8Ohm - SPL Peak: 105dB - Dispersion: 110 Degree Conical or Better - Frequency Range: 75 Hz-18 kHz - Sensitivity: 84dB - Transformer Tap 70V / 100V - Certification: UL1480 / UL2043 - Enclosure: Steel Backcan - Included Accessories: Metal Grille, C-ring, Paint Mask, Cutout Template etc all complete Make: Music Tribe / Bose / Martin Audio / AtlasIED or equivalent

SITC of 6.5" Coaxial In-Ceiling Loudspeaker - System Type: In-Ceiling Flush Mount Speaker - Driver Size: Min. 1 x 6.5” Driver or better - Power Continuous / Programme: 50 W / 100 W - Nominal impedance: 8Ohm - SPL Peak: 112dB - Dispersion: 110 Degree Conical or Better - Frequency Range: 75 Hz-18 kHz - Sensitivity: 90dB - Transformer Tap 70V / 100V - Certification: UL1480 / UL2043 - Enclosure: Steel Backcan - Included Accessories: Metal Grille, C-ring, Paint Mask, Cutout Template etc all complete Make: Music Tribe / Bose / Martin Audio / AtlasIED or equivalent

SITC of 8" Coaxial In-Ceiling Loudspeaker - System Type: In-Ceiling Flush Mount Speaker - Driver Size: Min. 1 x 8” Driver or better - Power Continuous / Programme: 90 W / 180 W - Nominal impedance: 8Ohm - SPL Peak: 116dB - Dispersion: 100 Degree Conical or Better - Frequency Range: 65 Hz-18 kHz - Sensitivity: 91dB - Transformer Tap 70V / 100V - Certification: UL1480 / UL2043 - Enclosure: Steel Backcan - Included Accessories: Metal Grille, C-ring, Paint Mask, Cutout Template etc all complete Make: Music Tribe / Bose / Martin Audio / AtlasIED or equivalent

SITC of Power Amplifier - Dual Channel Class D Amplifier with Energy Star Certification - Delivering 2 x 120 W @ 4/8 Ohms and 70V/100V - Distortion <0.05% - Frequency response 20 Hz to 20 kHz, - Signal-to-noise >97 dBA etc all complete Make: Music Tribe / Bose / AtlasIED or equivalent

SITC of Power Amplifier : - Dual channel 240 Watt Class D Amplifier with Energy Star Certification - Delivering 240W @ 4/8 Ohms and 70V/100V - Distortion <0.05% - Frequency response 20 Hz to 20 kHz - Signal-to-noise >97 dBA. Etc all complete Make: Music Tribe / Bose / AtlasIED or equivalent

SITC of Advanced Digital Audio Processor - AEC Mic Input: min 10 No's - Line Output: min 6 No's or more - USB Audio Interface 24Bit, 48Khz - GPIO Contcats: 6 No's or better - Built in 64 x 64 channel, dual-redundant Dante*/AES67 audio transport - 24 channels of freely assignable Acoustic Echo Cancellation - DANTE , Digital Audio Link Port for Future expansion - Frequency Response: 20Hz to 20KHz - Ethernet Port: Yes - RS232 connector for interfacing with 3rd party control systems - Crosstalk (inter-channel @ 1 kHZ): < 75 dB - Common mode rejection: Typically, -60 dB at 1 kHz - Input Gain range: 0 to +66 dB - Maximum input level: +24 dBu - Maximum output level: -31 dBu to +24 dBu - THD+N : <0.005%, - Dynamic range: > 105 dB - Certifictaion: CE , FCC etc all complete Make: Music Tribe / Biamp / AtlasIED or equivalent

SITC of 40 channel 48KHz Mixing Console - 32 mic inputs, 24 bus, 16 Aux outs. Main LCR out and Matrix outputs - Built in Stage Box Interface - 192 kHz, 24 bit ADC and DAC converters with minimum 112 dB dynamic range - Minimum 24 motorised 100 mm faders, - Optional wireless remote control for iPhone and iPad etc. - 32 x 32 channel USB 2.0 audio interface - 8 DCA and 6 mute groups - Built in Effect processor - Built in or external 100-Band for all Channel/Bus EQ 's - Auto-ranging universal switch-mode power supply - Digital mixer should be supplied with 32 inputs and 16 output stage Box etc. all complete. Make: Music Tribe / Allen Heath / Yamaha or equivalent

Digital Conference System and Microphone System SITC of Wireless Conference System: Central Unit to be access via Web Browser , - Control Min 150 microphone units - Unit to be accessed via web browser -Built-in OR external Wireless Access for Conference -6 microphone units can be turned on simultaneously - Minimum operating range of 30mtr or better - Range extension capability by looping more Conference access point - Support Quad Band System operates in the frequency range of 2.4 and 5 GHz - With built-in spectrum scanner to monitor the Frequency Band and detect interference sources - Web Browser quickly provides an information for usable frequency for conference system - Capability to block frequencies to ensure co-existence with other RF system - Multi Layer of security and entire system secured with Digital 128-bit encryption - Desktop CPU or Tablet can be used to access the Central wireless access unit via Web Browser - Software capability to create Microphone Group, Add Name Labels, Activate Microphone based on Name, Close Microphone etc - Superior Sound Clarity ensure the every speaker heard loud & clear - Conference Access Device to be connected with CPU of following parameter: Processor: i7, RAM: 8GB or more, USB: 4 x USB2.0, Monitor: 21", Keyboard & Mouse: Wireless, 1x RJ45 Ethernet Port Make: Televic / Shure / Bosch or equivalent

SITC of Wireless Conference System: Chairman Microphone Unit , - Chairman Microphone Unit with button to activate microphone - Integrated Priority button, Next-in-line button - Built-in loudspeaker - Speaker shall automatically muted when the microphone is active - Headphone output with volume control - Immune to Mobile Phone Interference - Multi Layer of security and entire system secured with Digital 128-bit encryption - Battery Status LED Indicator - integrated rechargeable batteries with Minimum operating time 25 hours etc all complete Make: Televic / Shure / Beyerdynamic or equivalent

SITC of Wireless Conference System: Delegate Microphone Unit , - Delegate Microphone Unit with button to activate microphone OR put in Request Mode after the Chairman Unit proide delegate the right to speak - Built-in loudspeaker - Speaker shall automatically muted when the microphone is active - Headphone output with volume control - Immune to Mobile Phone Interference - Multi Layer of security and entire system secured with Digital 128-bit encryption - Battery Status LED Indicator - integrated rechargeable batteries with Minimum operating time 25 hours etc all complete Make: Televic / Shure / Beyerdynamic or equivalent

SITC of Wireless Conference System: Charging and transport case - For up to 12 Microphones Units - Modular tiered case for storing microphones, Base Unit, Battery Pack, Wireless Access Controller & Charging tray for battery pack - Integrated power supply etc. all complete Make:Televic / Shure / Beyerdynamic or equivalent

SITC of Wireless Conference System: 400mm Gooseneck Microphone - GSM immune gooseneck microphone of length 400mm or more - Polar Pattern : Unidirectional, cardioid - Max SPL @ 1 kHz : 110 dB SPL (1% THD+N) - Signal to noise ratio> 67 dB(A) - Screw lock connector etc. all complete Make: Televic / Shure / Beyerdynamic or equivalent

SITC of UHF Wireless Handheld Microphone System - Cardioid dynamic - Receiving System : True Diversity - Modulation mode : FM - Frequency Response : 100 Hz to 15 kHz - RF Sensitivity: 20 dBuV at 60 dBA S/N ratio (50Ω termination) - Total Harmonic Distortion: <1.0% (at 1 kHz, ±20 kHz deviation) - Dynamic Range > 110dB - switch function : Mute/unmute & On/OFF - Operating range: 100 m (300'), typical (open range environment with no interfering signals) - RF Power Output High: 30 mW, Low: 10 mW (switchable) - No. of Channel : 10 channels per band - Antenna Input : BNC type, 50Ω - BIAS voltage 12V DC 60mA each for powering an antenna booster, active splitters, an antenna combiner or any other active component. - Maximum Output level XLR / Balanced: +9 dBV & 6.3 mm (¼"") / Unbalanced: +4 dBV - Balanced audio output attenuator : Two position switch: 0/-12 dB - Accessories Included: detachable Antennas, Rack mount kit etc. all complete. Make: Audio Technica / Shure / Sennheiser or equivalent

SITC of UHF Wireless Lapel Microphone System - Cardioid Condenser - Receiving System : True Diversity - Modulation mode : FM - Frequency Response : 100 Hz to 15 kHz - RF Sensitivity: 20 dBuV at 60 dBA S/N ratio (50Ω termination) - Total Harmonic Distortion: <1.0% (at 1 kHz, ±20 kHz deviation) - Dynamic Range > 110dB - switch function : Mute/unmute & On/OFF - Operating range: 100 m (300'), typical (open range environment with no interfering signals) - RF Power Output High: 30 mW, Low: 10 mW (switchable) - No. of Channel : 10 channels per band - Antenna Input : BNC type, 50Ω - BIAS voltage 12V DC 60mA each for powering an antenna booster, active splitters, an antenna combiner or any other active component. - Maximum Output level XLR / Balanced: +9 dBV & 6.3 mm (¼"") / Unbalanced: +4 dBV - Balanced audio output attenuator : Two position switch: 0/-12 dB - Accessories Included: detachable Antennas, Rack mount kit etc. all complete. Make: Audio Technica / Shure / Sennheiser or equivalent

SITC of UHF Wireless Headworn Microphone System - Cardioid Condenser - Receiving System : True Diversity - Modulation mode : FM - Frequency Response : 100 Hz to 15 kHz - RF Sensitivity: 20 dBuV at 60 dBA S/N ratio (50Ω termination) - Total Harmonic Distortion: <1.0% (at 1 kHz, ±20 kHz deviation) - Dynamic Range > 110dB - switch function : Mute/unmute & On/OFF - Operating range: 100 m (300'), typical (open range environment with no interfering signals) - RF Power Output High: 30 mW, Low: 10 mW (switchable) - No. of Channel : 10 channels per band - Antenna Input : BNC type, 50Ω - BIAS voltage 12V DC 60mA each for powering an antenna booster, active splitters, an antenna combiner or any other active component. - Maximum Output level XLR / Balanced: +9 dBV & 6.3 mm (¼"") / Unbalanced: +4 dBV - Balanced audio output attenuator : Two position switch: 0/-12 dB - Accessories Included: detachable Antennas, Rack mount kit etc. all complete. Make: Audio Technica / Shure / Sennheiser or equivalent

SITC of 4 - way Antena Distribution system - UHF (wide-band 440-900 MHz) active unity-gain diversity system - Enables one pair of antennas to feed Four wireless systems - Each distribution system must have identical independent 1-in by 4-out sections each providing a single antenna input, four isolated protected RF outputs and 1 cascade output - Interconnection of the units in a cascade fashion for an expanded system must be possible - All RF connections shall be rear panel mounted using standard BNC-type connectors - High OIP3 (+ 32 dBm) for maximum protection against intermodulation - 12V DC power to each antenna input to operate powered antennas or in-line RF devices up to 100 mA minimum. - Accessories Included: Rack mount kit & BNC cable x 8 etc. all complete Make: Audio Technica / Shure / Sennheiser or equivalent

SITC of Pair of UHF wide-band directional antennas - Operating Bandwidth : 470-990 MHz - Antenna Type : LPDA (log periodic dipole array) antennas - Impedance : 50 Ohms Typical - Gain : 6 dB Typical - Polar Pattern : Elliptical, 90° acceptance, typical - Polarization : Vertical (when mounted vertically) - Enhanced signal pickup for UHF wireless systems - The antennas must be constructed of industrial-grade copper-clad epoxy fiber-glass engineered to resist the effects of corrosion,UV degradation and vibration, providing long life and stable performance under difficult operating conditions - Must have High-quality, low-loss BNC connectors to minimize RF cable strain - Mounts should be 5 / 8 "-27 threaded fitting and designed to allow for vertical tilt adjustment through a 90°range - Horizontal adjustment should be possible by rotating the antenna in the mounting fitting etc. all complete Make: Audio Technica / Shure / Sennheiser or equivalent

SITC of Dynamic Vocal Microphone - ELEMENT: Dynamic - Pick up Pattern: Hypercardioid - Frequency Response : 60 - 14,000 Hz - Impedence : 500 ohms - Open Circuit Sensitivity: -54 dB (1.9 mV) re 1V at 1 Pa - Output Connector: 3 pin XLR Type - Rugged metal construction for long-lasting performance & neodymium magnet for improved output and transient response - Silent on/off operation design switch & Soft-touch finish for a secure, comfortable grip - Corrosion-resistant gold-plated XLRM-type connector - Accessories Included: Adjustable stand clamp & Soft protective Pouch - Certifictaion: CE etc. all complete Make: Audio Technica / Shure / Sennheiser or equivalent

SITC of Dynamic microphone for instruments - ELEMENT: Dynamic - Pick up Pattern: Hypercardioid - Frequency Response : 60 - 14,000 Hz - Impedence : 600 ohms - Open Circuit Sensitivity: -54 dB (1.9 mV) re 1V at 1 Pa - Output Connector: 3 pin XLR Type - Rugged metal construction for long-lasting performance & neodymium magnet for improved output and transient response - Silent on/off operation design switch & Soft-touch finish for a secure, comfortable grip - Corrosion-resistant gold-plated XLRM-type connector - Accessories Included: Adjustable stand clamp & Soft protective Pouch - Certifictaion: CE etc. all complete. Make: Audio Technica / Shure / Sennheiser or equivalent

SITC of Gooseneck Microphone - Cardioid Condenser - Gooseneck Length: 16.46" (418.0 mm) - Frequency Response : 70 - 16,000 Hz - Impedance : 100 ohms - Open Circuit Sensitivity: -37 dB (14.1 mV) re 1V at 1 Pa - Maximum Input Sound Level: 134 dB SPL, 1 kHz at 1% T.H.D. - Dynamic Range: 106 dB, 1 kHz at Max SPL - Signal-to-Noise Ratio: 66 dB, 1 kHz at 1 Pa - Desk Stand with ON/OFF Switch - Desk Stand Should Effectively isolates microphone from noise, shock and vibration transmitted through the mounting surface. - Output Connector: Integral 3-pin XLRM-type - Accessories Included: Windscreens - Certifictaion: CE etc. all complete. Make: Audio Technica / Shure / Sennheiser or equivalent

Touch Panel Control System SITC of Hardware Server Gateways - AV system control, room scheduling, and AV asset management - High IP Device Capacity for AV Control, Management, and Room Scheduling - Access from a web browser for setup and management - Dual Gigabit Ethernet ports - Supports Up to 10 rooms AV Control and 250 simultaneous IP connections Make: Atlona / Extron / Cue or equivalent

SITC of 10" Apple iPad with GUI Application and Table top kit and power supply etc all complete Make: Atlona / Extron / AMX / Cue or equivalent

SITC of IP to IR Command Converter etc all complete Make: Atlona / Extron / Cue

SITC of IP to Relay / Sensor Signal Converter etc all complete Make: Atlona / Extron / Cue or equivalent

SITC of IP to RS-232 Command Converter etc all complete Make: Atlona / Extron / Cue

SITC of 8-Button Network Control Panel etc all complete Make: Atlona / Extron / Cue or equivalent

SITC of Programmable 8 Port Relay Module & 4 digital / analogue input module 0-24 Volts DC, low-voltage relay, 6 Watts Power @ 12Volts / 240 V, 44k Input Impedence with cables & connectors as required Make: Make: Atlona / Extron / Aaztec or equivalent

Stage Lighting and Furnishing System SITC of Stage Furnishing - Main Front Stage Curtain (Size: 15 x 10 Meter) - Made out of Fire retardant Curshed ice Fabric with horizontal sliding arrangement complete - Fixing rails, brackets, sliding arrangement and Motorised operation complete with runners, master runners, pullies, 3mm steel wire rope, - One HP motors - 2 Nos., Air bracker contractors, - 2 Nos. micro switches for auto stop - 3 Nos. push buttons for forward, reverse and stop positions, Draped to half area when in closed position, minimum overlap at centre should be 900mm and should be stitched in double gathering with masking frill drop from prosc along with Motorised rail. with electric motor, Gear Box, running on bearings, switchable mode using Gear Box, railing System, Roller, Bearings, Relay, Limit Switch, Track etc. all complete. Make: Custom

SITC of Stage Furnishing - Rear Stage Curtain (Size: 13 x 10 Meter) - Made out of Glazzed Cotton / cashmilon with horizontal sliding arrangement - Fixing rails, brackets, sliding arrangement and Motorised operation complete with runners, master runners, pullies, 3mm steel wire rope, - one HP motors - 2 Nos., Air bracker contractors, - 2 Nos. micro switches for auto stop, 3 Nos. push buttons for forward, reverse and stop positions, draped to half area when in closed position, minimum overlap at centre should be 900mm and should be stitched in double gathering with masking frill drop from prosc along with Motorised rail. with electric motor, Gear Box, running on bearings, switchable mode using Gear Box, railing System, Roller, Bearings, Relay, Limit Switch, Track etc. all complete.

SITC of Stage Furnishing - Main Side Wings Made out of Glazzed Cotton / Cashmilon fixed on over head pivot track covered with Fabric Frame made up of MS Pipe etc. all complete.

SITC of Stage Furnishing - Frills mounted on frill bar made out of double gathering glazzed cotton / casminlon to be fitted above the stage with 32mm dia GI Pipe to Cover the lights and other other stage ceiling Gadgets etc. all complete.

SITC of Stage Furnishing - Side Ladder in Side Wings for Mounting Light Fixtures. Dimension: 2'x6'. Made up of with 1"x2" MS Pipe etc. all complete.

SITC of Stage Furnishing - Main Lights Bars (Back, Center and FOH Light Bars) ,made with 48mm GI pipe etc. all complete.

SITC of 400W LED Blinder Light 30 Degree - 3200K CCT Lamp source - DmX 512 dimming with 4 or 8 Channel modes - Black finish housing - IP20 protection - Strobe option and smooth dimming, - illuminate Stage with uniform light levels etc all complete Make: Leksa / Martin / ETC / Canara lighting or equivalent

SITC of 150W LED Par Light 6 in 1 Beam Angle 15° - RGBWUV 10W Lamp source x 12 Pcs - DmX 512 dimming with 10 Channel - Black finish housing - IP65 protection having Strobe option - illuminate the stage with unlimited colour effects for mood lighting etc all complete Make: Leksa / Martin / ETC / Canara lighting or equivalent

SITC of 100W High Quality LED Parcan Light - COB Lamp source 3200K CCT Colour temperature - CRI & TLCI Values above 90 - DmX 512 dimming with 2 channel conmtrol - Beam Angle of 11 - 35 Degree Zoomable, - Black powder coated Lux @ 2 Mtrs above 44,000 suitable for Stage lighting to illuminate the key areas etc all complete Make: Leksa / Martin / ETC / Canara lighting or equivalent

SITC of 200W LED 3200K Profile Spot 19 Degree Light - RGB Lamp source - DmX 512 dimming with 2Channel modes - Black finish housing - IP20 protection - Strobe option and smooth beam shaping cutters illuminate the key presentor or talent on stage etc all complete Make: Leksa / Martin / ETC / Canara lighting or equivalent

SITC of 350W LED Moving Head Spot complete with -Pan Range - 540° & Tilt Range - 270° -8 Bit/ 16 Bit High Precision Movement -Auto Pan-tilt correction -3 Colour Wheels – 9 Colours + CMY -Motorized Irish effect -1 Static Gobo Wheel – 10 Fixed Metal Gobos -7 Interchangeable Glass Gobos -8 Facet Prisms Rotating -Motorized Zoom from 7° ~ 31° -Linear dimming 100% ~ 0% -Motorized Focus and Frost -Inbuilt auto focus function -LCD Easy view display -Data DmX through 3 / 5 Pin XLR’s -IP20 rated product etc all complete Make: Leksa / Martin / ETC / Canara lighting or equivalent

SITC of Light fixture mouting clamp - Customized for suspending on fixed bars on stage made up of Aluminium or MS material- - black powder coating matt black finish etc all complete

SITC of Light Fixture dual safety chain - Made up of GI wire rope bundled and twisted together - Load bearing capacity above 200 Kgs, sleve on the rope etc all complete

SITC of Suspender cum clamps designed as per site conidition made out of MS material - black powder coated finish suitable to hold various stage rigs like lighting bar,FoH bar, curtain tracks, wings and other stage equipments etc all complete

SITC of C Profile MS Hot rolled strips 3mm thick with extra U bend used either to create basic supports for various auditorium stage rigs, duly powder coated with matt black texture finish paint etc all complete

SITC of Power Distribution Electrical Panel - Incomer of 120A floor mount / rack mount / wall mount with nuetral separation - Incomer of L&T or Schneider make, Voltmeter, Ammeter display for reading visualization, - Individual MCB control for 60 outgoing circuits - Separate incomer control for Motor control panel supply - RYB Phase indicators internally wired using IS certified wires and cables, - Provided with ivery connectors for the internal terminations and external outgoing connecting points custom built etc all complete

SITC of Opto isolated RDM enabled DmX splitter unit - Power In and safety fuse - 8 Output channels 5 Pin XLR in and out supporting DMX operation as per DmX 512 protocol etc all complete Make: Leksa / Zero 88 / Avolite or equivalent

SITC of 96 Channel Dimming Controller with DmX 512 Output protocol, - 96 Direct access DmX channels, - 5 Pin XLR output, - Scene mode having 96 fader saving options for program pre-sets, - Sequence and chase operations, - In built memory battery etc all complete Make: Leksa / Zero 88 / Avolite or equivalent

SITC of PVC insulated PVC sheathed, 3 Core 2.5 sqmm FRLS copper Cables for Each Complete Light Set Up etc. all complete. Make: Polycab / Finolex / Havells or equivalent

SITC of 5 Core DmX Cables for Each Complete Light Set Up etc. all complete. Make: Polycab / Finolex / Falcon or equivalent

SITC of Accessories, clamp etc. for above stage furnishing and lighting system etc all complete

Recording and Streaming System SITC of Recording & Streaming Server, 3 DVI-I (Analog & Digital Signals), VGA Loop out, Input format HDMI, DVI, RGBHV, YPbPr, CVBS, Full HD Resolution, H.264 High Profile, AAC audio encoding, FIle format MP4 / MPEG4, Picture in picture, Picture by picture, Manegement through App, Webpage, dedicated software, Built in approx 1TB storage, with all mounting Accessories etc. all complete. Make: Reach / Extron / Epiphane or equivalent

Cable, Connectors and accessories SITC of High Speed HDMI Cable: 3 Feet etc. all complete. Make: Kramer / Kordz / Belden / Canare / Sommer or equivalent

SITC of High Speed HDMI Cable: 10 Feet etc. all complete. Make: Kramer / Kordz / Belden / Canare / Sommer or equivalent

SITC of High Speed HDMI Cable: 35 Feet etc. all complete. Make: Kramer / Kordz / Belden / Canare / Sommer or equivalent

SITC of High Speed HDMI Cable: 50 Feet etc. all complete. Make: Kramer / Kordz / Belden / Canare / Sommer or equivalent

SITC of DisplayPort to HDMI Cable: 3 Feet etc. all complete. Make: Kramer / Kordz / Belden / Canare / Sommer or equivalent

SITC of 4K DisplayPort Cable: 3 Feet etc. all complete. Make: Kramer / Kordz / Belden / Canare / Sommer or equivalent

SITC of 4K DisplayPort Cable: 6 Feet etc. all complete. Make: Kramer / Kordz / Belden / Canare / Sommer or equivalent

SITC of USB 2.0 Type–C Cable: 3 feet etc. all complete. Make: Kramer / Kordz / Belden / Canare / Sommer or equivalent

SITC of USB 2.0 Type–C Cable: 6 feet etc. all complete. Make: Kramer / Kordz / Belden / Canare / Sommer or equivalent

SITC of 12AWG 2 Core Speaker Cable (as per actual) etc. all complete. Make: Kramer / Kordz / Belden / Canare / Sommer or equivalent

SITC of 14AWG 4 Core Speaker Cable (as per actual) etc. all complete. Make: Kramer / Kordz / Belden / Canare / Sommer or equivalent

SITC of 14AWG 2 Core Speaker Cable (as per actual) etc. all complete. Make: Kramer / Kordz / Belden / Canare / Sommer or equivalent

SITC of 16AWG 2 Core Speaker Cable (as per actual) etc. all complete. Make: Kramer / Kordz / Belden / Canare / Sommer or equivalent

SITC CAT6A cable F/UTP (as per actual) etc all complete Make: Kramer / Kordz / Belden / Canare / Sommer or equivalent

SITC of 2 Core Sheilded Audio/Control Cable (as per actual) etc all complete Make: Kramer / Kordz / Belden / Canare / Sommer or equivalent

SITC of Connector and Accessories etc all complete Make: MX / Nuetrick/ Amphenol or equivalent

SITC of Rack Structure 42 U Air Cooled AV Equipment Rack with Two Nos. of Vertical Power Strips, Cantilever Selves, Cable routing perforations, 4 No. of Spin Wheels etc. all complete. Make: Valrack / Aaztec / FSS or equivalent

SITC of Rack Structure 20 U Air Cooled AV Equipment Rack with 4 Nos. of Vertical Power Strips, Cantilever Selves, Cable routing perforations, 4 No. of Spin Wheels etc. all complete. Make: Valrack / Aaztec / FSS or equivalent

SITC of Rack Structure 12 U Air Cooled AV Equipment Rack with 4 Nos. of Vertical Power Strips, Cantilever Selves, Cable routing perforations, 4 No. of Spin Wheels etc. all complete. Make: Valrack / Aaztec / FSS or equivalent

Lifts Supply,Installation,testing Commissioning of Below described lifts complete as per specification and as per direction of Engg-In Charge Passanger 16 Persons (1088 KG) (With m/c Room) Lift with speed of 1.5 M/Sec., travel of ground to sixth:7Stop/7 Open,power operated doors, ACVVVF Control, and automatic rescue operation during power failure. (Hospital, dimensions and travelling as per drawing)

16 Persons (1088 KG) (With m/c Room) Lift with speed of 1.5 M/Sec., travel of ground to Fourth:5Stop/5 Open,power operated doors, ACVVVF Control, and automatic rescue operation during power failure. (Academic+lacture, dimensions and travelling as per drawing)

20 Persons (1360 KG) (With m/c Room) Lift with speed of 1.5 M/Sec., travel of ground to Fourth:5Stop/5 Open,power operated doors, ACVVVF Control, and automatic rescue operation during power failure. (Academic+lacture, dimensions and travelling as per drawing)

16 Persons (1088 KG) (With m/c Room) Lift with speed of 1.5 M/Sec., travel of ground to Fourth:5Stop/5 Open,power operated doors, ACVVVF Control, and automatic rescue operation during power failure. (Admin, dimensions and travelling as per drawing)

10 Persons Capsule (680 KG) (With m/c Room) Lift with speed of 1.5 M/Sec., travel of ground toSecond:3Stop/3 Open,power operated doors, ACVVVF Control, and automatic rescue operation during power failure. (Library Block, dimensions and travelling as per drawing)

Passanger/BED Lift 20 P Bed (1360 KG) (With m/c Room) Lift with speed of .75 M/Sec., travel of ground to sixth:7Stop/7 Open,power operated doors, ACVVVF Control, and automatic rescue operation during power failure. (Hospital, dimensions and travelling as per drawing)

20 P Bed (1360 KG) (With m/c Room) Lift with speed of 0.75 M/Sec., travel of ground to Fourth:5Stop/5 Open,power operated doors, ACVVVF Control, and automatic rescue operation during power failure. (Academic+ lacture, dimensions and travelling as per drawing)

20 P Bed (1360 KG) (With m/c Room) Lift with speed of 0.75 M/Sec., travel of ground to Fourth:5Stop/5 Open,power operated doors, ACVVVF Control, and automatic rescue operation during power failure. (Admin, dimensions and travelling as per drawing)

20 P Bed (1360 KG) (With m/c Room) Lift with speed of 1.0 M/Sec., travel of ground to Sixth:7Stop/7 Open,power operated doors, ACVVVF Control, and automatic rescue operation during power failure. (Boys Hostel, dimensions and travelling as per drawing)

20 P Bed (1360 KG) (With m/c Room) Lift with speed of 1.0 M/Sec., travel of ground to Fourth:5 Stop/5 Open,power operated doors, ACVVVF Control, and automatic rescue operation during power failure. (Girls Hostel, dimensions and travelling as per drawing)

20 P Bed (1360 KG) (With m/c Room) Lift with speed of 1.0 M/Sec., travel of ground to Seventh:8Stop/8 Open,power operated doors, ACVVVF Control, and automatic rescue operation during power failure. (JR. Sr. Hostel, dimensions and travelling as per drawing)

20 P Bed (1360 KG) (With m/c Room) Lift with speed of 1.0 M/Sec., travel of ground to Second:3Stop/3 Open,power operated doors, ACVVVF Control, and automatic rescue operation during power failure. (Lecture Block, dimensions and travelling as per drawing)

20 Persons (1360 KG) (With m/c Room) Lift with speed of 1.0 M/Sec., travel of ground to Fifth:6Stop/6 Open,power operated doors, ACVVVF Control, and automatic rescue operation during power failure. (Nurses Hostel, dimensions and travelling as per drawing)

20 Persons (1360 KG) (With m/c Room) Lift with speed of 1.0 M/Sec., travel of ground to Fourth:5Stop/5 Open,power operated doors, ACVVVF Control, and automatic rescue operation during power failure. (Type-3, dimensions and travelling as per drawing)

20 Persons (1360 KG) (With m/c Room) Lift with speed of 1.0 M/Sec., travel of ground to Fifth:6Stop/6 Open,power operated doors, ACVVVF Control, and automatic rescue operation during power failure. (Type-4, dimensions and travelling as per drawing)

20 Persons (1360 KG) (With m/c Room) Lift with speed of 1.0 M/Sec., travel of ground to Three:4Stop/4 Open,power operated doors, ACVVVF Control, and automatic rescue operation during power failure. (Type-5, dimensions and travelling as per drawing)

Dumb Waiter 250 KG Dumb waiter at hospital 7Stop/7 Open with speed of .25 MPS/ with SS Hailine Finish complete in all respect

Addition and deletion of cost per floor on below stated size of lift as per requirement of site 10 Persons (680 KG) (With m/c Room) Lift with speed of 1.5 M/Sec.,

16 Persons (1088 KG) (With m/c Room) Lift with speed of 1.5 M/Sec.

20 Persons (1360 KG) (With m/c Room) Lift with speed of 1.5 M/Sec.

20 Persons (1360 KG) (With m/c Room) Lift with speed of 1.0 M/Sec.

Hot Water Generator (HWG) Supply,installation, testing & Commissioning of electrically operated Hot Water Generator of of following actual capacity made of 8mm M.S. sheet and dish end made of 10mm M.S. having 16 gauge stainless steel lining with heaters arranged in banks and Controller and Thermostat so that required qty. of hot water is generated at 50°C with nominal variation, including 100mm thick resin bonded fibre glass insulation of 24 Kg / CUM density finished with 1.25mm thick aluminium sheet cladding including necessary Electrical panel with BMS compatible having suitable Incoming and outgoing Switchgears for Boiler, automatic Controls including inlet and outlet connections for water complete with pressure release valve, low level cut-out, Autovent sight-glass as per specification complete as required. (Degree of protection IP52 with IS 2147) Heating capacity : 100 KW Water in temp. : 45 deg C Water out temp : 50 deg C Flow Rate : =100 USGPM HWG as Above ( 1 Working+1 STAND BY)

Condenser Water Pumps Supply, erection, testing and commissioning of Centrifugal End suction back pull out condenser water pump set capable of delivering 1800 USGPM of water against 28 mtr head each comprising of the following and complete as per specifications and as required. 1 No. - Split Casing/end suction back pull out type pump with bronze impellar, S.S Shaft, CED Coated CI body and mechanical seal., base frame and foundation 1 No. Suitable HP, TEFC squirrel cage induction motor with class 'F' insulation,Eff-1, 1450 RPM synchronous speed, operating on 415 Volts ± 10 %, 3 phase, 50 Hz A.C. supply. Unless otherwise specified, renewable wear ring of bronze shall be furnished atleast on the casing Pump as above (2 working+1 STAND BY )

Chilled Water Primary Pumps Supplying, erection, testing and commissioning of Centrifugal Vertical Split Casing/ End Suction back pull out primary chilled/hot water pump set capable of delivering 1080 USGPM of water against a head 15 Mtr. each pump shall comprise the following as required as per specifications. 1 No. - End Suction back pull out type pump with bronze impeller, S.S Shaft, CED Coated C.I body and mechanical seal.base frame and foundation Duly insulated with 80 kg/cum density resin bonded fiber glass cladded with aluminium sheets of 0.5mm thickness and properly clamped to pump in two semicircular sections as per specifications. 1 No.- Suitable HP, TEFC squirrel cage induction motor with class 'F' insulation,IP -55 Protection,Eff-1, 1450 RPM synchronous speed, operating on 415 volts ± 10%, 3 phase, 50 Hz A.C. supply. Pump as above (2 working+1 stand by)

Chilled Water Secondary Pumps (variable pumping system)- For Chilled/ Hot water Supplying, erection, testing and commissioning of package type End Suction back pull out Secondary chilled/hot water pumping system with VFD and all pump system controller, comprising of: Pumping set with base frame and foundation ,CED Coated cast Iron casing, Bronze impellers with stainless steel shaft, connected to suitable capacity TEFC ventilated induction motor with class 'F' insulation, Eff-1, 3 Phase, 1450 RPM, suitable for 415 volts ± 10%, 3 phase, 50 Hz A.C. supply. Duly insulated with 80 kg/cum density resin bonded fiber glass cladded with aluminium sheets of 0.5mm thickness and properly clamped to pump in two semicircular sections as per specifications. Unless otherwise specified, renewable wear ring of bronze shall be furnished atleast on the casing Microprocessor based control panel shall have suitable hardware & software so that it can be integrated directly to IBMS with standard communication open protocol using backnet / Modbus as well as open IP. (All the Pump set will have their control panel with respect to the motor rating). All pumps to be provided with separate variable frequency drives. Control panel should also consist of cooling fan. One panel for each job will be provided (for a set of two pumps) and the panels should be installed adjacent to each other. The pumps should be suitable for heating as well as chilled water circulation. Lot-Mounting frame work with anti vibration pads. Necessory 2 nos. of Ectronic Differential Pressure Transmitters and control wiring (control wiring is quantified in electrical Sub head) as required. suitable flanged suction and delivery headers in C-Class MS Complete set system to be mounted on a common MS base frame and shall follow following duty with following no. of pumps: Secondary chilled/hot water pump sets Flow Rate : 1080 USGPM Head : 35 Metre WC Pump no ( 2W+1 stand by )

Hot water pump Supply,erection, testing and commissioning of monoblock Hot water centrifugal pump for hot water recirculation, pump set capable of delivering 100 USGPM of water against 45 mtr head each comprising of the following and complete as required 1 No. - monoblock type pump with bronze impellar and mechanical seal. Duly insulated with 80 kg/cum density resin bonded fiber glass cladded with aluminium sheets of 0.5mm thickness and properly clamped to pump in two semicircular sections as per specifications. 1 No. Suitable HP, TEFC squirrel cage induction motor(Eff-1) with class ' B' insulation, 3000 RPM synchronous speed, operating on 415 Volts + 10 % , 3 phase , 50 Hz A.C. supply. Pump as above (1 working + 1stand by)

Cooling Towers Supply, installation, testing and commissioning of Induced draft FRP Cooling tower suitable for 17.6 lacs K.cal/hr heat rejection capacity with PVC fillings with intergal louvers and drift eliminators open pan sutaible for water distribution complete with hot FRP water basin either fitted with spray nozzles or having self rotating sprinklers, statically and dynamically balanced one / two nos. axial flow type fan-direct driven or driven through special bevelled reduction gear box with TEFC induction motor with IP-55 protection,Eff-1, suction screen, make up and quick fill arrangement, overflow and drain connections and suitable inspection ladder, access arrangement for cooling tower interior, anti vibration mountings, base frame etc complete as per specifications and as required. Water Leaving Temperature : 29.5 Deg C Water Entering Temperature : 34.5 Deg C Water Flow Rate : 1800 USGPM Ambient Wet Bulb Temperature : 25.5 Deg C Cooling Tower as Above ( 2 working+1 stand by)

AIR HANDLING UNITS Supplying, installing, testing and commissioning of factory built Floor mounted double skin type air handling units for OT with thermal break profile made of 43 mm thick panels consisting of pre plasticized G.I. casing of thickness 0.8 mm outside layer and 0.8 mm thick plane aluminium sheet inside layer with polyurethene foam (PUF) insulation of density 32 kg/m3 factory injected between them by injection moulding machine, complete with blower section with blower DIDW backward/ Forward curved centrifugal fan of 125 mm WC static pressure, 6 row deep cooling coil, 2 row heating coil, section with aluminium finned copper tubes (tube thickness not less than 0.5mm), filter sections with 50 mm thick washable synthetic type Pre filters having efficiency 90% down to 10 micron and Fine filters having efficiency 99% down to 3 micron ( MERV-13) or HEPA filter for OT ahus with belt drive package with TEFC drive motor (EFF-1) suitable for VFD operation at 415 ± 10% volts, 50 Hz, 3 phase, A.C supply, complete with mixing box, drain connections with drain valve, stainless steel drain pan, thermometers and pressure gauge at the inlet and outlet of the coils, necessary vibration isolation arrangement etc, complete as per specifications of following capacities: The above AHU shall be install with steam type humidifier package & cost of pan type humidifier of 3kw is included in ahu item . it should have remote controlled provision in the OTs for temp. & RH adjustment. (The AHU shall be interloked with digital temp. & RH controller) 3000 CFM (12 TR)

3500 cfm (17 TR)

Supplying, installing, testing and commissioning of factory built Floor mounted double skin type air handling units made of follwing panels thickness consisting of pre plasticized G.I. casing of thickness 0.8 mm outside layer and 0.8 mm thick plane G.I sheet inside layer with polyurethene foam (PUF) insulation of density 32 kg/m3 factory injected between them by injection moulding machine, complete with blower section with blower DIDW centrifugal fan of following static pressure, cooling /heating coil, section with aluminium finned copper tubes (tube thickness not less than 0.5mm), filter sections with 50 mm thick washable synthetic type Pre filters having efficiency 90% down to 10 micron and Fine filters with MERV-13 rating (as mentioned below), belt drive package with TEFC drive motor (EFF-1) suitable for 415 ± 10% volts, 50 Hz, 3 phase, A.C supply, complete with mixing box(as mentioned below), drain connections with drain valve, stainless steel drain pan, thermometers and pressure gauge at the inlet and outlet of the coils, necessary vibration isolation arrangement etc, complete as per specifications of following capacities: following with 6 RD Cooling coil , 2 RD Heating coil /43 mm thick panel/ backward curved fan/ 70 MM WG static Ppre filter+Fine Filter (MERV-13), with Mixing box 15000 cfm

following with 6 RD Cooling coil , 43 mm thick panel, backward curved fan/ 50 MM WG static Pre filter with Mixing box 10000 cfm

following with 6 RD Cooling coil /43 mm thick panel/ backward curved fan/ 65 MM WG static Ppre filter+Fine Filter (MERV-13), with Mixing box 5500

Mixing box 6500

Mixing box 8000

Mixing box 8500

Supplying, installing, testing and commissioning of factory built Ceiling Suspended double skin type air handling units made of 25 mm thick panels consisting of pre plasticized G.I. casing of thickness 0.6 mm outside layer and plane GI of 0.6mm inside layer with polyurethene foam (PUF) insulation of density 32 kg/m3 factory injected between them by injection moulding machine, complete with blower section with blower DIDW centrifugal fan of following static pressure, cooling/ heating coil section with aluminium finned copper tubes (tube thickness not less than 0.5mm), filter sections with 50 mm thick washable synthetic type pre filter having efficiency 90% down to 10 micron & Fine filters (as mentioned), belt drive package with TEFC drive motor (EFF-1) suitable for 415 ± 10% volts, 50 Hz, 3 phase, A.C supply, complete, drain connections with drain valve, test point for pressure guage & thermometer at the inlet and outlet of coil, stainless steel drain pan ,necessary vibration isolation arrangement etc, complete as per specifications of following capacities: Following with 6 RD Cooling coil/ 2 RD Heating coil, backward /forward curved fan , 70 MM WG static,pre+Fine Filter (MERV-12) 2500 cfm

Following with 6 RD Cooling coil, backward /forward curved fan , 65 MM WG static,pre+Fine Filter (MERV-12) 2000 cfm

Following with 6 RD Cooling coil, backward /forward curved fan , 50 MM WG static,pre filter 2000 cfm

FAN COIL UNITS Supply, installation, testing and commissioning of ceiling suspended High static type FCU's each complete with 3 row deep cooling coil of copper tubes aluminium fins construction, centrifugal fan, 3 speed motor, filters insulated drain pan, coil piping connections, condensate drain connection, complete as required complete with bronze ball valve with and without strainer, PIBCV valves, cooling & heating thermostats and electrical wiring, manual air vent valve, SP isolator with MS enclosure box should be Provided etc. as required as per specification & drawings with the following capacities:- 2.0 TR

Supply, installation, testing and commissioning of ceiling suspended Normal static type FCU's each complete with 3 row deep cooling coil & 1 row deep heating coil of copper tubes aluminium fins construction, centrifugal fan, 3 speed motor, filters insulated drain pan, coil piping connections, condensate drain connection, complete as required complete with bronze ball valve with and without strainer, PID valves, three way valve, thermostats and electrical wiring, manual air vent valve, SP isolator with MS enclosure box should be Provided etc. as required as per specification & drawings with the following capacities:- 1.0 TR

VARIABLE FREQUENCY DRIVES Supply, Installation, testing & commissioning of HVAC dedicated VFDs suitable for the following AHU fan motor capacity (The integration of the VFD with AHU is included in this item) with IP 54 enclosures with Mains disconnect, complying with the tender specifications and having: Built-in dual 5% impedance DC link reactor (harmonic filters) on the positive and negative rails of the DC bus of the VFD. Built-in EMC Filters (electromagnetic compatibility filters) for VFDs for restriction of conducted emissions to comply with IEC61800: 3 (unrestricted distribution): 2004 Category C 1, for required length of cable between motor & VFD. Two/Three -feedback PID (Propotional integrated derivative) controller having capability to simultaneously accept 2/3 feedback signals from temperature sensors for process optimization and accordingly regulate the speed of the AHUs. Automatic Energy Optimization for maximum energy savings. The VFD shall be compatible with BMS. 1.1 KW

Supply, installation, testing & commissioning of Duct mounted factory assembled ultra violet germicide irradicator system of 99% kill rate of air borne mold, spores, bacteria, viruses & odour etc. Specification of UVGI system as per the specification: 500-1000 CFM

2000-3500 CFM (OT)

Ductable Split Units (for UPS) Providing, fixing, testing and commissioning of 11.0 TR (Nominal) Ductable split air-conditioning unit suitable to operate from 415+10% volt, 50 Hz, 3 phase power supply, with air-cooled evaporator with coil, fan, and fan motor, air-cooled condenser with hermetically sealed scroll compressor condenser coil, propeller fans controls, inter connection control panel, Including control wiring. only Raw power will be provided by other agency near the outdoor units, necessary power cable with isolator, M.S. frame duly painted to locate Outdoor Unit. Refrigerant pipe size and gas quantity should suit to the copper pipe length at actual. The capacity guarantee should be ensured by the vender.

Supply, installation and testing of Refrigerant piping (total circuit including liquid & suction) with interconnecting cabling between indoor / outdoor units as per site incharge, 13 mm thick XLPE/Nitrile rubber insulation on pipes, gas charging, support complete in all respects for 11.0 TR Ductable Split AC.

SUB HEAD 'B' - VENTILATION AIR WASHER UNITS ( For Kitchen Ventilation ) Supply, Installation, testing and Commissioning of double skin type air washer units with minimum 90 % saturation efficiency made of 25 mm thick panels consisting of pre-plasticized G.I. casing of thickness 0.63 mm outside layer and 0.63 mm thick plane GI sheet at inside layer with polyurethane foam (PUF) insulation with density of 40 kg/cum. factory injected between them by injection moulding machine, complete with 50mm thick HDPE prefilter, 200mm deep cell-deck pad , water distribution header, indigenous pump, internal piping GI 'B' class, valves & fittings, MS water tank with FRP lining, DIDW centrifugal forward curved fan and fan motor ( EFF-1) with IP-55 protection suitable for 415 +10% volts, 3 phase, 50 Hz A.C supply , V-belt & drive set vibration isolators quick fill, make up, drain, overflow connection and TP isolator with MS enclosure box complete in all respects etc. The unit shall be of following capacities with 40 mm WC static pressure. 12000 CFM

WET SCRUBBER UNIT( For Kitchen Ventilation ) Supply, Installation, testing and Commissioning of wet scrubber unit, constructed of 16 G GSS duly powder coated , complete with backward curved SISW fan, motor and drive (both fan and motor shall be mounted on a common frame using cushy foot mounting) suitable for operation on 415 ± 10% voltage, 50 Hz A/c 3 phase, MS water tank with FRP lining, float valve, monoblock pump, distributor, nozzels, drift eleminator, required piping & valve from tank to pump distributor as required and TP isolator with MS enclosure box complete in all respects. The unit shall be of following capacities with 65 mm WC static pressure. 14000 CFM

Supply, Installation, testing and Commissioning of ceiling / floor mounted Rectangular box type/circular type Inline fan, for toilet exhaust , ot exhaust , lab exhaust constructed of GSS duly powder coated as per detailed specifications, complete with forward curved SISW fan, motor and drive suitable for 220 ± 10% volts, 1 phase, 50 Hz A.C supply, with necessary canvas connection etc complete in all respects. 800 CFM with 15 mm static pressure

400 CFM with 15 mm static pressure for toilet and lab exhaust/fresh air

1100 CFM with 15 mm static pressure for toilet and lab exhaust

Supplying, installation, testing & commissioning of Propeller type exhaust air fans suitable for following capacities complete with electric motor suitable for operation on 220 V+ 10%,50 Hz, 1 phase AC supply fitted with speed regulator, mountings, frames, louvers and bird screen etc. of the following capacities. 200 mm dia

SUB HEAD 'C' - PIPING WORKS INSULATED CHILLED WATER PIPING (Inside Buildings) Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water/hot water piping plumbing inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with fire retardant quality expanded polystrene moulded pipe section of density 20 kg/cu.m after a thick coat of cold setting adhesive (CPRX compound) wrapping with 500g polythene faced hessain and finally applying 0.63mm aluminium sheet cladding complete with type3 , grade 1 roofing feltstrip(as per IS:1322 as amended up to date ) at joints repairing of damage to building etc. as per specifications and as required complete in all respect. Note:- The Pipes of sizes 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. 400mm dia.(75 mm thick insulation)

350mm dia.(75 mm thick insulation)

300mm dia.(75 mm thick insulation)

250mm dia.(75 mm thick insulation)

200mm dia.(75 mm thick insulation)

150mm dia.(75 mm thick insulation)

125mm dia.(50mm thick insulation)

100mm dia.(50mm thick insulation)

80mm dia.(50mm thick insulation)

65mm dia.(50mm thick insulation)

50mm dia.(50mm thick insulation)

40mm dia.(50mm thick insulation)

32mm dia.(50mm thick insulation)

25mm dia.(50mm thick insulation)

Supply, installation, testing and commissioning of Pre-insulated Valves, Strainers of following sizes as per specifications and drawings. BUTTERFLY VALVE WITH ON/OFF TYPE MOTORIZED ACTUATOR Single phase 220V with limit switches, C I body & PN 16 pressure rating SS Disc & shaft of Feedback, BMS Compatible for chilled water circulation as specified duly insulatated of following sizes as per specification and drawings. Cost should include necessary control wire (minimum size 1.5 sq.mm) 200mm dia.

80mm dia.

BUTTERFLY VALVE (MANUAL) with C I body, SS disc, nitrile rubber seal & O - ring & PN 10 pressure rating as specified. 300mm dia.

200mm dia.

150mm dia.

100mm dia.

80mm dia.

65mm dia.

50mm dia.

BALANCING VALVE with built in measuring facility with CI body flanged conrtuction with EPDM coated disc with long pitch & PN 16 pressure rating as specified. 200mm dia.

100mm dia.

80mm dia.

65mm dia.

50mm dia.

40mm dia.

NON - RETURN VALVE with dual plate of CI body, SS plates vulcanized NBR seal flanged end & PN 10 pressure rating as specified. 200mm dia.

80mm dia.

50mm dia.

Y - STRAINER of ductile CI body flanged ends with stainless steel strainer as specified. 200mm dia.

100mm dia.

80mm dia.

65mm dia.

50mm dia.

32mm dia.

25mm dia.

Ball Valve duly insulated of the following sizes as per specifications and drawings. 40mm dia.

32mm dia.

25mm dia.

20mm dia.

PRESSURE INDEPENDENT BALANCING CUM CONTROL VALVE WITH THERMOSTAT Pressure Independent Balancing cum Control Valve (PIBCV) which shall be 2 way combined valve of PN 16 rating for flow limitation, controlling flow & controlling Delta P. Valve body upto 32mm shall be brass and cast iron above 32mm.Valve should be equipped with electronic modulating actuator for AHU which can accept either "4(0)-20 mA / 2(0)-10 V DC signals. Operating voltage for actuator shall be 24 V DC, valve should be provided with required capacity of transformer for converting AC to DC. The actuator should be connected to proportionate thermostat. Delta p controller should ensure 100% control valve authority always at all load conditions (part load and full load).Stepless balancing adjustments shall be in valve and control adjustments in actuator. Valve along with actuator and cold thermostat shall offer logarithmic control characteristics complete as per specification. The flow rates of chilled water are as below : 25MM

Supply, Installation, testing and commissioning of thermostat for various air handling Units.( For CHW/HW Connection)

Supply, Installation, testing and commissioning of microprocessor based temperator & RH controller with sensor for various air handling Units.(Suitable for CHW & monsoon reheat Connection)

Supply, Installation, testing and commissioning of thermostat for various air handling Units.

Providing & fixing in position the industrial type pressure gauge complete with accessories as required.

Providing & fixing in position the mercury in glass industrial type thermometer complete with accessories as required.

Supply, Installation, testing and commissioning of Flow Switch with accessories as required.

Auto Air - purge valve of 20 mm dia (Air Vent will be fitted with an isolating ball valve )

FLEXIBLE CONNECTIONS Supply ,Installation ,Testing and commissioning of Flexible connector for following Dia. pipe suitable for PN 16 pressure rating to be installed at pump and chiller suction and discharge . 200mm dia.

100mm dia.

80mm dia.

50mm dia.

EXPANSION TANK Supply, installation, testing of open type expansion tank of MS Construction made of 6 mm thick mild steel sheet duly insulated with 50mm thick T.F quality expended polystyrene of 24 kg/cum density covered with a layer of 120 gm/sqm polythene sheet (vapour barrier) and finally cement plastered over chicken wire netting of 24 gauge and complete with vent and outlets for system connection over flow and drain 40 mm dia. Make up connection with float valve drain valve and incoming line valves, vent connections, valves and fittings as required. 1000 X 1000 X 1000 (High)- For Summer Cooling/Winter Heating

Supply, installation, testing and commisisoning of insulated GI medium class condensate drain water piping with bends reducers tees, supports etc. The insulation shall be with pipe sections of nitrile rubber of 9 mm thick as per specifications and drawings. 65mm dia.

50mm dia.

40mm dia.

32mm dia.

25mm dia.

Supply,installation,testing and commissioning of of CPVC pipes having thermal stability for condesate water including wrapping of 9mm thick class 0 nitrile rubber insulation with suitable adhesive with all CPVC plain and brass threaded fittings including the pipes with clamps 1metre spacing.This including jointing of pipes with one step CPVC solvent cement and testing of joints complete as per drg and specifications 50 mm dia

40 mm dia

32 mm dia.

25 mm dia

CONDENSER WATER PIPE Supplying, fixing, testing and commissioning of condenser water pipes of following sizes of MS 'C' class along with necessary clamps, vibration isolators and fittings such as bends,tees etc.but excluding valves, strainers, gauges etc. adequately supported on rigid supports duly painted/buried in ground excavation and refilling etc. as per specification and as required complete in all respect. Note:-The Pipes Note:-The Pipes size 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. And from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. 300 mm dia.

250 mm dia.

200 mm dia.

150mm dia.

125mm dia.

100mm dia.

Supplying, fixing, testing and commissioning of following valves, gauges and strainers for condenser water circulation as per specifications.without insulation Supplying, fixing, testing and commissioning of following sizes Motorized Butter fly Valve with CI Body, SS Disc,O - ring and minimum PN-16 pressure rating , conforming to BS 5155, IS 13095, with IP-55 actuator, capable of accepting upto 10V DC , and upto 20mA electric signal and providing similar transduced feedback output to control system as required. 250mm dia.

BUTTERFLY VALVE (MANUAL) with C I body SS disc nitrile sheet & O - ring & PN 16 pressure rating as specified. 400mm dia.

250mm dia.

100mm dia.

50 mm dia.

BALANCING VALVE with built in measuring facility with C I body flanged construction with EPDM Coated disc with long pitch with protded out pipe insulation & PN 16 pressure rating as specified. 250 mm dia.

NON - RETURN VALVE with dual plate of CI body, SS plates vulcanized NBR seal flanged end & PN 16 pressure rating as specified. 250mm dia.

Y - STRAINER of ductile CI body flanged ends with stainless steel strainer as specified. 250mm dia.

FLEXIBLE CONNECTIONS Supply ,Installation ,Testing and commissioning of Flexible connector for following Dia. pipe suitable for PN 16 pressure rating to be installed at pump and chiller suction and discharge . 250mm dia.

Providing & fixing in position the industrial type pressure gauge complete with accessories as required.

Providing & fixing in position the mercury in glass industrial type thermometer complete with accessories as required.

Supply, Installation, testing and commissioning of Flow Switch with accessories as required.

SUB HEAD 'D' - AIR DISTRIBUTION WORKS Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. Thickness 0.63 mm sheet

Thickness 0.8 mm sheet

Thickness 1 mm sheet

Thickness 1.25 mm sheet

Supply, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. Thickness 0.63 mm sheet

Thickness 0.8 mm sheet

Thickness 1 mm sheet

Thickness 1.25 mm sheet

Supply, installation, testing & commissioning of thermal insulated flexible duct of following sizes duly supported at regular interval as per site requirement etc. complete as required as per specifications. 200 mm dia.

Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class "O") insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required. 19 mm for return air duct

25 mm for suuply air duct

Supply, Fabrication, Installation and testing of MS sheet metal circular ducts , accordance with the approved shop floor drawings and specifications. 1.25 mm thickness welded sheet MS ducting for kitchen exhaust.

Supply, installation, testing & Commissioning of opposed blade 20 Gauge G.I volume control dampers within ducts to be provided with suitable links, louvers, and quadrants for manual control of volume of air flow and for proper balancing of the air distribution system.

Supply, Installation,testing, and commissioning of black anodised extruded Aluminium collor damper complete with nuts, screws etc at supply air terminals . as per approved drawings and specfications.

Supply, fixing and commissioning of powder coated extruded aluminum Linear Grilles complete with nuts, bolts, screws etc. as per approved drawings and specifications.

Supplying, installation, testing and commissioning of fire dampers, the blades and frame shall be min. 1.6 mm thick GI and factory fitted in a sleeve made out of 1.6 mm thick GI of min. 400 mm long, as & where required, of required sizes including control wiring. The damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the event of fire signal. CBRI tested and certified for 90 minute fire rating etc. complete as required and as per specifications. (Total assembly should be UL listed) Fire damper

Motorized Actuator with control and temperature sensor complete with all respects.

Supplying, installation, testing and commissioning of motorised volume control dampers on/off type with actuator and blades & frame shall be min. 1.6 mm thick GI sheet and factory fitted in a sleeve made out of 1.6 mm thick GI Sheet of min. 400 mm long, as & where required, of required sizes including control wiring. Motorized damper

Motorized Actuator with control and temperature sensor complete with all respects.

Supply, installation, testing and commissioning of anodised aluminium Fresh air louvers with bird screen & damper, as per specifications and drawings.

Supply, installation, testing and commissioning of anodised aluminium exhaust air louvers with bird screen, as per specifications and drawings.

Supply, fixing and commissioning of powder coated extruded aluminum grilles / diffuser complete with nuts, bolts, screws etc. as per approved drawings and specfications. Supply, fixing and commissioning air grilles with Al. volume control damper

Supply, fixing and commissioning Return air grilles without volume control damper

Supply, fixing and commissioning Supply air diffuser with Al. volume control damper measured with neck size

Supply, fixing and commissioning Return air diffuser without volume control damper measured with neck size

Supply, fixing and commissioningSupply air jet nozzle/diffuser with collar damper complete with all accessories . - 400 dia

Air Differential Pressure Switch Supply,installation,testing and commissioning of air differential pressure switches complete with sensor probe , etc. integrated with Light and visual alarm signal, as per general details and specifications to be installed across HEPA filter bank sections for Operating rooms & Cath Labs with necessary control and power wiring.

Temperature and RH sensor and adjuster package. Supply,installation, testing and commissioning of micro-processor based Room temperature , humidity sensor and remote adjuster package within a MS housing on wall having a stainless steel cover plate.This package shall have a temperature and humidity display - red 2" high LED character for operation rooms. Sensor, adjuster (Snap acting humidistat/Proportional thermostat- Microprocessor based) and displayer package, as described above. (Suitable for For CHW , Monsoon reheat & humidifire Connection)

Supply, installation, testing and commissioning of single duct VAV Terminal unit with automatic moterized volume control dampers, sensor, controller & actuator assembly, 24V transformer, ON/OFF switch, hanger alongwith 2 x 1.5 sqmm control wiring & conduiting complete in all respect. 1500 to 2000 CFM

2000 to 3000 CFM

Supply, fixing and commissioning of commissioning of non vision air transfer door grille of powder coated extruded aluminium, single deflection grille with horizontal vanes arrangement etc. as per specifications and drawings.

AIR CURTAIN Supply,installation testing and commissioning of AIR CURTAIN of following size as per approved make . 1200 mm long (High flow type)

1500 mm long (High flow type)

SUB HEAD 'E' - INSULATION Supplying, fixing acoustic lining on wall and ceiling of AHU rooms with 25mm thick Rigid Board of Glasswool one side aluminum faced and other side black glass cloth lamination, having density of 80 kg/cu.m; friction fixed in 610mm X 610 mm frame; work made of 25X25X18 mm made out of 22 G thick GI sheet U shaped channel. The accoustic board should be placed in such a way that black glass cloth is visible from inside the AHU room & complete as required and as per specifications.

Supplying following 1.1kV grade, XLPE insulated, heavy duty armoured cables suitable for 415V, 50Hz, AC system, with inner and outer PVC sheath, galvanised steel armouring and with all components as mentioned in BOQ, specifications, complete as required. 3.5 Core 300 Sqmm. Alum. Armd

3.5 Core 185 Sqmm. Alum. Armd

3.5 Core 95 Sqmm. Alum. Armd

3.5 Core 70 Sqmm. Alum. Armd

3.5 Core 35 Sqmm. Alum. Armd

3 Core 16 Sqmm. Alum. Armd

3 Core 10 Sqmm. Alum. Armd

3 Core 6 Sqmm. Alum. Armd

4 Core 16 Sqmm. Alum. Armd

4 Core 10 Sqmm. Alum. Armd

4 Core 6 Sqmm. Alum. Armd

Supplying and making end termination with brass compression glands and aluminium/ copper lugs as required for following size of XLPE insulated and PVC sheathed aluminium/ copper conductor cable of 1.1 KV grade etc. complete as required & approved by the Engineer In Charge. 3.5 Core 300 Sqmm. Alum. Armd

3.5 Core 185 Sqmm. Alum. Armd

3.5 Core 95 Sqmm. Alum. Armd

3.5 Core 70 Sqmm. Alum. Armd

4 Core 25 Sqmm. Alum. Armd

3 Core 35 Sqmm. Alum. Armd

3 Core 16 Sqmm. Alum. Armd

3 Core 10 Sqmm. Alum. Armd

4 Core 6 Sqmm. Alum. Armd

4 Core 16 Sqmm. Alum. Armd

4 Core 10 Sqmm. Alum. Armd

4 Core 6 Sqmm. Alum. Armd

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size on cable tray as required. Upto 35 sq. mm (clamped with 1mm thick saddle)

Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)

Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable indoor and outdoor , thermostat , pibcv valve actuator control wire in surface/ recessed medium class PVC conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

Supplying, installation, testing & commissioning of following sizes of GI flexible pipe with all accessories like GI coupler, GI plate etc. complete as required, approved by the Engineer In Charge. 20 mm dia.

25 mm dia.

Supply, Fabricating and installation following size of perforated GI cable trays including horizontal and vertical GI bends, reducers, tees, cross members and other accessories as required and duly suspended from the ceiling with M.S. suspenders and including painting etc. complete as required & approved by the Engineer In Charge. 150 mm. Width x 50mm. Depth x 1.6mm. Thickness.

300 mm. Width x 50mm. Depth x 1.6mm. Thickness.

450 mm. Width x 50mm. Depth x 2.0 mm. thickness.

600 mm. Width x 75mm. Depth x 2.0 mm. thickness.

900 mm. Width x 75mm. Depth x 2.0 mm. thickness.

Earthing with GI earth plate 600 mm x 600 mm x 6 mm thick including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal / coke and salt as required.

Providing and fixing 25 x 5 mm G.I. Strip in 40 mm dia. G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required

SUBHEAD -I: VENTILATION EQUIPMENT Supply, installation, testing and commissioning of Fan Section unit FOR TOILET EXHAUST of single skin construction made of pre-plasticized 18 G thick GI sheet for exhaust air consisting of DIDW centrifugal forward curve fan and fan motor complete with TEFC squirrel cage induction motor suitable for 3 Phase 50 Hz 415 V ± 10 % AC supply with class-F insulation (EFF-1), mounted within the housing, 'V' belt drive package, vibration isolators & necessary canvas connection with flange & bird screen at outlet etc. of the following capacities. The fan static pressure shall be 30 mm WC. 10000CFM

SMOKE EXTRACTION Supply, installation, testing and commissioning of Axial flow fan for supply air of following capacity having 15 mm WC static with powder coated GSS/M.S. casing and aluminium alloy impellers with high efficiency aero-foil sections, blades, the impeller directly driven by TEFC induction motor (efficiency 2) suitable for 3 Phase 50 Hz 415 V ± 10 %,1400 RPM of class 'h' insulation etc., suitable capacity of TP isolator with MS enclosure box complete as required and as per specifications . Fans should be statically & dynamically balanced . Class H , 250 Deg c for 2 Hrs . 10000 CFM

PRESSURIZATION Supply, installation, testing and commissioning of floor mounted / ceiling hang Axial flow type supply air fan for Lift well, lobby & stairwell pressurization of following capacity with powder coated GSS/M.S. casing and aluminium alloy impellers with high efficiency aero-foil sections, blades, the impeller directly driven by TEFC induction motor (efficiency 1) and 'F' class insulation suitable for 3 Phase, 50 Hz, 415±10% Volt, TP isolator with M.S enclosure box complete as required and as per specifications. Fans should be statically & dynamically balanced.The fan static pressure shall be 20 mm WC static. 7000 CFM for pressurization ( floor mounted)

3000 CFM for pressurization ( floor mounted)

5000 CFM for pressurization . ( floor mounted)

SUBHEAD -II: AIR DISTRIBUTION WORK Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. Thickness 0.63 mm sheet

Thickness 0.8 mm sheet

Thickness 1 mm sheet

Thickness 1.25 mm sheet

Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers complete as required

Supplying & fixing of powder coated extruded aluminium Supply Air Grills with aluminium volume control dampers as per specifications.

Supply, installation, testing and commissioning of fresh air/ exhaust air Louver comprising of powder coated GI louvers with bird screen as required.

Supply, installation & testing of GI back draft dampers (16 G Blade & Frame) similar constrction to gravity louvers (for Basement fans- fire case as specified in the drawing.) , provided with suitable links to prevent the back pressure of air.

SUBHEAD -III: ELECTRICAL WORK Terrace Ventilation panel-1 ( L.H.S) Outdoor type with IP-55 Protection Incoming:315 Amp TPN MCCB (35 KA) (Ics=Icu upto 433 V) thermal magnetic release with over current and short circuit releases, all indication, front operating handle & door interlock ) 3 Nos. Phase indication LED lamps with 2 Amps back up MCB, breaker ' ON/OFF' indicating light with 2A MCB 1 No. Intelligent multi-function digital panel meters of class 0.5 accuracy with communication interface port RS 485 for recording V (Between Phases and between each phase and neutral, A (In each phase and neutral), KWHr with suitable rating CTs, CT shorting links, R,Y, B LED indicating lamp and 2 A control SP MCB's. Bus Bar :TPN aluminium extensible type main bus bars of minimum of400 Amp capacity and auxiliary bus bar of suitable capacity with heat shrinkable coloured sleeves and i/c DMC/ SMC bus bars supports at required intervals complete for cross section, size supports & their spacing etc Outgoings: 63Amp TP,10 kA MCCB , ON/OFF indications, complete as required. - 12 set. 40Amp TP,10 kA MCCB , ON/OFF indications, complete as required. - 10 set. Ventilation Panel as above

VRF FOR ACADEMIC, LIBRARY , LECTURE , ADMIN Supply, installation, testing and commissioning of all inverter compressor based variable refrigerant volume modular type airconditioning system complete with indoor and out door units with individual controller and with refrigerant piping, control cabling as per detail given in specifications and having following items: Outdoor Unit (10 HP) For AHU .1 (3500 CFM)

(14 HP) For AHU (4500 CFM)

(16 HP) For AHU (5500 CFM)

(20 HP) For ADMIN & library

(26 HP) For AHU (8500 CFM)

Supply, Installation ,testing and commissioning including vaccumiazation and Nitrogen testing o ffollowing nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRFsystem, complete with fittings ,with suitable adjustable ring type hangers upports,jointing /brazing including accessories, insulated with XPLE Class- O tubular insulation /with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines ,all accessories as per specifications etc. as required : 41.27 mm dia(OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation

38 mm dia(OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation

34.9 mm dia(OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation

31.8 mm dia(OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation

28.58mm dia(OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation

25.4 mm dia(OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation

22.2 mm dia(OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation

19 mm dia(OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation

15.86 mm dia(OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation

12.7 mm dia(OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation

9.5 mm dia(OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation

6.4 mm dia(OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation

Corded remote Controllers

Main centrallised inteligent touch manager controller .

Interconnecting 'Y' Joints i.e. Refnet Joints/ Header with Y-joints and headers

SITC of low static static (25 pascal esp) units for vrf complete with accessories canvas connection , supports angle/channel , vibration isolators as per drwgs 1 TR

SITC of high static (110 pascal esp) units for vrf complete with accessories canvas connection , supports angle/channel , vibration isolators as per drwgs 5.5 TR

SITC of Mild static ductable (45 pascal ESP) units for VRF complete with accessories canvas connection , supports angle/channel , vibration isolators as per drwgs 1.8 TR

Electric Panel Board academic for outdoor units Supply, installation, testing and commissioning of main panel board outdoor IP 55 typr cubical compartmentalised, floor mounted made of 2.0 mm thick steel sheet duly painted complete with voltmeter, ammeter, indicating lights on/off push button omplete as per specifications and drawings. 1 No. 200 Amps TPN MCCB incoming. 1 set of 250 Amps TPN bus bar duly sleeved. 4 No. 63 Amps MCCB+ELCB outgoing for outdoor

Electric Panel Board ADMIN for outdoor units Supply, installation, testing and commissioning of main panel board outdoor IP 55 typr cubical compartmentalised, floor mounted made of 2.0 mm thick steel sheet duly painted complete with voltmeter, ammeter, indicating lights on/off push button omplete as per specifications and drawings. 1 No. 200 Amps TPN MCCB incoming. 1 set of 250 Amps TPN bus bar duly sleeved. 5 No. 63 Amps MCCB+ELCB outgoing for outdoor

Electric Panel Board LIBRARY for outdoor units Supply, installation, testing and commissioning of main panel board outdoor IP 55 typr cubical compartmentalised, floor mounted made of 2.0 mm thick steel sheet duly painted complete with voltmeter, ammeter, indicating lights on/off push button omplete as per specifications and drawings. 1 No. 200 Amps TPN MCCB incoming. 1 set of 250 Amps TPN bus bar duly sleeved. 5 No. 63 Amps MCCB+ELCB outgoing for outdoor

Electric Panel Board Audi, Supply, installation, testing and commissioning of main panel board cubical compartmentalised, floor mounted made of 2.0 mm thick steel sheet duly painted complete with voltmeter, ammeter, indicating lights 2 Nos100 Amps MCCB outgoing along with DOL starter for upto 17 kw for DUCTABLE UNIT AUDITORIUM

Supply & installation of weather proof isolator with suitable rating near each outdoor unit the prices should be inclusive of copper cabling from isolators to outdoor units. 100 Amps

Supply, Installation, Testing & commissioning of Air Cooled Ductable Split Units: Capacity - 17 Tr -6500 cfm - 40 mm static(auditorium)

NON MEDICAL EQUIPMENTS FOR MODULAR OPERATION THEATRE (As per Specifications) Wall & Ceiling System with required support structure, anti bacterial paint

CLEAN AIR SYSTEM WITH HEPA FILTERS

DOORS 1500 X 2100 FOR DOCTORS ENTRY

1000 X 2100 FOR PATIENT ENTRY

PERIPHERAL LIGHTING

Operation Theatre Control Panel Touch screen

X-RAY VIEWING SCREENS

OPERATION THEATRE FLOORING (ANTISTATIC CONDUCTIVE )

OPERATION LIST BOARD

OT Light with Provision of Camera

CAMERA WITH MIN. 30 INCH MEDICAL GRADE MONITOR

OPERATION THEATRE MANAGEMENT SYSTEM (HARDWARE + SOFTWARE)

DOUBLE ARM MOVEABLE PENDANT FOR ANESTHETIST

DOUBLE ARM MOVEABLE PENDANT FOR ANESTHETIST

Electrical installation

IPS System

OT INTEGRATION

Mobile Intra operative workstation

MEDICAL GAS PIPELINE SYSTEM (As per Specifications) OXYGEN SYSTEM Oxygen Supply System with Fully Automatic Control Panel

Oxygen outlets with probes

Oxygen flowmeter complete with humidifier bottle.

Oxygen H.P. antistatic rubber tube

NITROUS OXIDE SYSTEM Nitrous Oxide System with Fully Automatic Control Panel

Nitrous Oxide outlets (Imported)with probes

Nitrous Oxide H.P. antistatic rubber tube

MEDICAL AND SURGICAL AIR SYSTEM Medical and surgical air system min. 2700 LPM as per specification

Compressed M.Air- 4Bar outlets (Imported)

Compressed Surgical- 7Bar outlets (Imported)with probes

Compressed air H.P. antistatic rubber tube

VACUUM SYSTEM Vacuum system minimum 3000 LPM as per specification

Vacuum outlets (Imported) with probes

Vacuum H.P. antistatic rubber tube

Ward vacuum unit as per specification

Theatre vacuum unit as per specification

AGSS Plant (CE certified with four digit notified body number) AGSS Duplex system as per specification

AGSS outlets

BED HEAD PANEL 2 Gas Outlet(O2-1+Vac-1) with 5/15 Amp. Switch & Sockets and provision for Nurse call system.The bed head panel is made of high strength extruded aluminum. It is powder coated to make it aesthetically appealing and long lasting. The panel is divided into different sections to segregate low voltage, high voltage and medical gas chamber. The panel consist of special railings to hang various items like humidifier bottles, vaccine basket, examination lamp, suction jar, IV pole, etc. which facilitates patient treatment. The bed panel should have provision for Medical Gas outlet points (2 Gas outlet, 3 gas outlet, 4 gas outlet as per requirement) and Nurse call system, It should be equipped with Electrical Switch Socket of 5/15 Amp., data socket and Telephone socket.

3 Gas Outlet(O2-1+M.Air-4-1+Vac-1) with 5 Amp. 3 Nos.Switch & Sockets and provision for Nurse call system The bed head panel is made of high strength extruded aluminum. It is powder coated to make it aesthetically appealing and long lasting. The panel is divided into different sections to segregate low voltage, high voltage and medical gas chamber. The panel consist of special railings to hang various items like humidifier bottles, vaccine basket, examination lamp, suction jar, IV pole, etc. which facilitates patient treatment. The bed panel should have provision for Medical Gas outlet points (2 Gas outlet, 3 gas outlet, 4 gas outlet as per requirement) and Nurse call system, It should be equipped with Electrical Switch Socket of 5/15 Amp., data socket and Telephone socket.

4 Gas Outlet (O2-2+M.Air-4-1+Vac-1) with 5 Amp. 3 Nos. Switch & Sockets and provision for Nurse call system.The bed head panel is made of high strength extruded aluminum. It is powder coated to make it aesthetically appealing and long lasting. The panel is divided into different sections to segregate low voltage, high voltage and medical gas chamber. The panel consist of special railings to hang various items like humidifier bottles, vaccine basket, examination lamp, suction jar, IV pole, etc. which facilitates patient treatment. The bed panel should have for Medical Gas outlet points (2 Gas outlet, 3 gas outlet, 4 gas outlet as per requirement) and Nurse call system, It should be equipped with Electrical Switch Socket of 5/15 Amp., data socket and Telephone socket. The Bed head panels & gas outlets should be CE certified with 4 digit notified body no. and should be from same principal/ manufacturer.

Medical Grade copper pipe with required copper fittings 76 mm outer dia, 1.5mm thick

54mm outer dia, 1.2mm thick

42mm outer dia, 1.2mm thick

28mm outer dia, 0.9mm thick

22mm outer dia, 0.9mm thick

15mm outer dia, 0.9mm thick

12mm outer dia, 0.7mm thick

FLOOR ISOLATION VALVES 15 MM

VALVE WITH VALVE BOX AND PRESSURE GAUGE 6 Gas Services

4 Gas Services

3 Gas Services

2 Gas Services

AREA LINE PRESSURE ALARM 5 Services

4 Services

3 Services

2 Services

Master Alarm

Electrical Work for Compressors, Vacuum Pumps, AGSS and Dryers Electrical wiring & conduiting for compressors and vacuum pumps

LAUNDRY EQUIPMENTS (As per Specifications) Make: Fabcare/ Ecoclean/ Globbus or equivalent GENERAL WARD / STAFF UNIFORMS / PATIENTS UNIFORM Barrier Washer Extractor, High Spin 50 Kg Capacity, Steam Heated.

Drying Tumbler Machine 30 Kg. cap. per charge. Steam Heated, Front loading type. * Rust proof machine for its entire life.

CRITICAL WARD / SLUICING WARD Barrier Washer Extractor, High Spin 18 Kg Capacity, Steam Heated.

Drying Tumbler Machine 15 Kg. cap. per charge. Steam Heated, Front loading type. * Rust proof machine for its entire life.

IRONING AND FINISHING EQUIPMETNS Flat Work Ironer Machine Single Roller, Steam heated Roller Heated Size of the roller 800 dia X 3000 MM length

Vacuum Steam Ironing Machine Size: 4’ x 2.5’ with all fittings. * Industrial Steam Iron * Iron Mat * Aluminum Shoe * Solenoid Valve Complete in all respect.

Mobile Table Size 2½’ X 10’.

Mobile Table Size 2½’ X 4’.

General Utility Press, Steam Heated, pneumatic operated. (without air compressor)

TRANSPORTATION & STORAGE FURNITURE Dry Linen Trolley (Cage Type) 50 Kg. cap.

Wet Linen Trolley (Box Type) 50 Kg. cap.

Double Sink (S.S.), Scrubbing Station

Shelf Trolley with shelves and revolving wheels. 100 Kg. Capacity

Diesel Fired Boiler 600 Kg. cap. with diesel tank

Stainlesss Steel 316 carriage suitable for Rectangular Sterilizer

Stainlesss Steel 304 trolley suitable for above carriage

S.S. Control and packing table with drawer table is used for separation, control and packing of various sets of sterilized goods for wards, clinics, operation theatres etc. and is designed for standing and sitting workers. A removable hatch made of laminated particles board is provided. The hatch contains a SS drawer and a laminated particles board plate. Overall size: 2000mm L x 1400mm W

Stainless steel Work Table Table is used for wet goods with undershelf. The table top is fabricated out of 16 SWG SS 304 qlty. ground and polished to a smooth surface without high edge sections. The table top frame is a complete assembly with front, back and two ends welded together at corners. Overall size 1500mm x610x890Ht.

S.S. Vertical Sliding Door Door is used between clean and dirty areas in hospitals, pharmaceuticals etc. The sliding door is mounted on an existing wall opening. The door is made of stainless steel counter-balanced by built in counterweight. The door is provided with nylon wheels at the side for easy of movement. The door is made along with stainless steel cover plates for the wall opening. The door is provided with a built in safety lock which ensures the door from closing if the counterweight rope breaks. Opening 500 x 500mm

Stainless steel work table with two sink The bench top is fabricated out of 16SWG SS 304 qlty. ground and polished with smooth surface and edge section. The top is designed to give a stable work surface. The table top frame is a complete assembly with front, back and two ends welded together. The sinks are made of stainless steel with inside ground and polished. Each sink is provided with a drain valve and a strainer. On the bench top, just above the sinks mixer for hot and cold water connection is provided. Overall size 2400mmL x650mm Wx900mm Ht

Washer Disinfector Washer Disinfector, single door, suitable for cleaning and disaffection of surgical instruments, anesthetic equipment, suction bottles, cleaning buckets, general circulation goods, dental tray and glassware with a fully closed process. The washer disinfector, fully automatic, has an advanced micro-processor which controls all services, programming and statistic functions. For safety reasons the service and programming functions are coded. The door would be provided with interlocking system. The chamber is equipped with four spray arms which ensure good water penetration from all directions. Various attachments are provided to suit the load to be washed. Suitable dosage of detergent can be preset with the dosing pump. The provision of a double wall with insulation in between enables the Washer Disinfector to run with minimum sound and heat emission. The wash chamber, the inside the door, the pipework system and the circulation arms are made entirely of stainless steel. Suitable for electrical operation on 400/440 volts, 3 phase, AC supply, electrical load 13 KW Capacity of 275 ltrs.

Ultrasonic Cleaner Ultrasonic Cleaner of overall size 530mm L x 330mm W x350mm H Internal Dimensions: 505 x 300 x 200 mm, output frequency 35khz. Capacity 30 litres. The unit will be complete with a thermostat and a timer, insert basket for tank and tank cover. The unit is suitable for electrical operation on 220/240 Volts, single phase, 50 cycles, AC supply.

Stainless steel racks with 5 shelves, all sides open and stainless steel bullet feet. overall size 1830x535x 1830mmH.

Stainless steel table trolley with 2 shelves Stainless steel table trolley with 2 shelves is for use in the sterile goods store when batching sterile goods for delivery and also for short internal transport. The trolley is also suitable for use as a temporary storage or utility space at packing tables. The frame is mounted on 4nos. heavy duty swiveling castors for easy movement in narrow passages. Overall size 1080x530x800H

Gauze cutting machine with SS table size 900x600x750mm

Single Distilled Water Still Single Distilled Water Still, generally as per the Barnstead Type. The Still is guaranteed to produce pyrogen free and chemically pure water to comply with IP/BP Standards. The evaporator, the multi-baffle and the condenser will be made out of stainless steel with the joints welded. The condenser will be provided with stainless steel tubes, water inlet and outlet connection.The Water Still will be supplied in a ready to use condition mounted on a suitable stand.Water Still as above of capacity 20 litres, per hour suitable for electric operation on 400/440 volts, 3 phase AC supply, electrical load being 15 KW.

Stainless Storage tank, electric load 6 kw., capacity 120 litres.

Spray Gun Rinser attached with SS working table and SS sink Spray Gun Rinser with attachments is used for cleaning syringes, catheters, endoscopes, cystoscopes and variety of other instruments and articles used in sterile services.

Kitchen Equipments for Hospital Make: Electrolux/ Globbus or Equivalent MILK BOILER Cap.100Ltrs. S.S.Sheet insulated body with triple jacket. The water jacket will be fitted with 2 Kw heating element. Milk outlet, water level indicator & draw off valve at the bottom & water tank. Phillips element, Elcon thermostat, GVC rotary switch, LED indicator for Power, 4mm thickness 3 core wire

TEA BOILER Cap.100Ltrs. S.S.Sheet insulated body with triple jacket. The water jacket will be fitted with 2 Kw heating element. Milk outlet, water level indicator & draw off valve at the bottom & water tank. Phillips element, Elcon thermostat, GVC rotary switch, LED indicator for Power, 4mm thickness 3 core wire

MICROWAVE OVEN Cap.20-30Ltrs.

PICK UP COUNTER WITH OVERSHELF Size 1800X600X850+300 Top 3 sides, under & over shelf of s.s.sheet, on m.s.angle & s.s.tubular legs frame work. The counter will have 3 sides fully covered, operator side open. With one under shelf. One over shelf 300mm wide & running along the full length of counter u type heating element of 1 Kw is placed under the one head shelf to keep the dishes warm provided with toggle switch also connected with 4 mm 3 core wire.

WORK TABLE FOR SUPPORT OF TWO BURNER RANGE Size 1350x600x850mm Top & undershelf of s.s.sheet on m.s.anlge frame work & s.s.tubular legs, with adjustable feet. Top to have sound deadning material lining as required.

TWO BURNER COOKING RANGE App. Size 1200X600X850mm Frame work of m.s.anlge duly painted, mounted on s.steel tubular legs with adjustable feet. Top & sides & under shelf of s.s.sheet. The range will be complete with 2nos. Hy-pressure gas burners with individual control valves. Cast iron pan support

FOR Community kitchen TWO BURNER COOKING RANGE App. Size 1200X600X850mm Frame work of m.s.anlge duly painted, mounted on s.steel tubular legs with adjustable feet. Top & sides & under shelf of s.s.sheet. The range will be complete with 2nos. Hy-pressure gas burners with individual control valves. Cast iron pan support

EXHAUST HOOD (Without Ducting, Fixing & Extraction fan) FOR TWO BURNER RANGE Size 1950x750x600mm Made of s.steel sheet, 20G thick duly welded & pop rivetted as required. The hood will be complete with s.s.sheet removable type baffle filters. Complete with greese collection channel & greese collection cup/s.

JUICER (table top model) Cast Aluminum/CI body, duly polished / painted, with worm & perforated insert. Top feeding tray. Worm easily cleanable fitted with 1/2HP elect. motor.

CONVEYOR TOASTER App. Cap. 100-125 Toasts/hr. S.S.Sheet body, having s.s.sheet conveyor belt. App.225mm wide. The unit will have heating elements on top & lower portion of conveyor belt with variable heat & speed control switch. (MADE IN ITALY)

WORK TABLE WITH SINK FOR JUICER STATION Size 1800x750x850+150 Top & Sink bowl of s.s.sheet, on s.s.anlge & s.s.tubular frame work with cross bracing at lower portion. Sink bowl will be integrally welded with top & grinded smooth. Sink bowl size 450x450x250mm.

WORK TABLE WITH SINK FOR IDLY STEAMER Size 1950x600x850+150 Top & Sink bowl of s.s.sheet, on s.s.anlge & s.s.tubular frame work with cross bracing at lower portion. Sink bowl will be integrally welded with top & grinded smooth. Sink bowl size 450x450x250mm.

UNDER COUNTER REFRIGERATOR WITH PICK UP SHELF Size 1200x600x850+450+300 Double walled 'PUF' insulated s.s.sheet outer & inner body of s.s.sheet 0.8mm thick having hinged doors with rubber gascuts. Inside s.s.wire shelves on adjustable channel frame complete with 'Kirloskar/Tecumesh' make compressor. Having condensor,

FOUR DOOR REFRIGERATOR App. Size 1200x675x2000mm Double walled, insulated 'PUF' body made of 0.8mm thick s.s.sheet. Inside chamber to have 4nos. S.s.wire shelves on adjustable channel. The unit will have 4 doors with magnatic rubber gascuts & locking provision. The condensing unit, consisting of 'Kirlos

WORK TABLE Size 1500X600X850mm Top & undershelf of s.s.sheet on m.s.anlge frame work & s.s.tubular legs, with adjustable feet. Top to have sound deadning material lining as required.

EXHAUST HOOD (Without Ducting, Fixing & Extraction fan) Size 1950x750x600mm Made of s.steel sheet, 20G thick duly welded & pop rivetted as required. The hood will be complete with s.s.sheet removable type baffle filters. Complete with greese collection channel & greese collection cup/s.

WORK TABLE Size 1500X600X850mm Top & undershelf of s.s.sheet on m.s.anlge frame work & s.s.tubular legs, with adjustable feet. Top to have sound deadning material lining as required.

DOSA PLATE O/S 1500X600X850 Framework made of m.s. angle of size 38x38x5mm and 25x25x5 mm. Top made of 16 mm thick m.s. plate with stainless steel channel for draining the excess oil from fry top. The verticals of the equipment are made of stainless steel of size 38 mm dia and cross

IDLY STEAMER (CAP. - 104 IDLY per batch) STD MODEL Made of stainless steel sheet, fitted with Elect. Controls.

EXHAUST HOOD (Without Ducting, Fixing & Extraction fan) for low height burner Size 1650x750x600mm Made of s.steel sheet, 20G thick duly welded & pop rivetted as required. The hood will be complete with s.s.sheet removable type baffle filters. Complete with greese collection channel & greese collection cup/s.

LOW HT. TABLE for supporting low height burner Size 750x750x600mm Specification same as that of work table but the table will be without undershelf & will have cross bracing support at lower portion.

LOW HT. BURNER Size 750x750x600mm Specification same as that of cooking range but the unit will be without undershelf, but will only have cross bracing support at lower portion.

EXHAUST HOOD (Without Ducting, Fixing & Extraction fan) for 03 burner cooking range Size 1650x750x600mm Made of s.steel sheet, 20G thick duly welded & pop rivetted as required. The hood will be complete with s.s.sheet removable type baffle filters. Complete with greese collection channel & greese collection cup/s.

THREE BURNER COOKING RANGE O/S 1800X600X850 Structure made of m.s. angle of size 38x38x5mm, duly rust proof painted. Top of 16Swg thick s.s.sheet. All four side covered up to height of app. 10” by 20Swg stainless steel sheet. Bottom stainless steel stripes sheets complete with gas burners.

WORK TABLE for support of 03 burner cooking range Size 1500X600X850mm Top & undershelf of s.s.sheet on m.s.anlge frame work & s.s.tubular legs, with adjustable feet. Top to have sound deadning material lining as required.

EXHAUST HOOD (Without Ducting, Fixing & Extraction fan) for bulk cooker/boiler & fryer Size 1950x750x600mm Made of s.steel sheet, 20G thick duly welded & pop rivetted as required. The hood will be complete with s.s.sheet removable type baffle filters. Complete with greese collection channel & greese collection cup/s.

BULK COOKER/boiler TILTING TYPE Cap.160Ltrs. Specification same as Sno.13 but the frying pan will be Of rectangular shaped with 12”depth & a pouring lip & the unit will be fitted with v type high pressure gas burner with control valve & pilot lamp.

BULK FRYER TILTING TYPE Cap.100Ltrs. Triple jacketed body of stainless steel sheet, Inner most jacketed of 16g thick with 12g thick dish ended bottom, second wall for air gap of 18g stainless steel sheet & outer insulation jacket also of 18g stainless steel sheet. The unit will have counter

WET GRINDER Cap.15ltrs (1.0HP) Stainless steel sheet constd. Body with s.s.sheet constd. Revolving drum, cromium plated pillar support on m.s.angle frame work fitted with electric motor gear box & grinding stones & coconut scraper.

DOUGH KNEADING MACHINE (CROMPTON MOTOR 2.0 HP) App. Cap of Bowl 25Ltrs. S.S.Mixing bowl, with s.s.rod/strip mixing arm, mounted on steel tubular & sheet frame work duly painted. Complete with 1.0HP Elect. Motor with control switch.

POTATO PEELER Cap.15Kg./chrgs.(CROMPTON MOTOR 1.0 HP) 16 gauge Stainless steel sheet peeling drum, lined inside with Abrasive material, stainless steel /cast iron rotating peeling disc. Top of the drum will have a potato inlet door, waste Inlet provision peeled potato discharge door & waste water Outlet pipe

PULVeRISER (Std.) (CROMPTON MOTOR 1.0 HP) Stainless steel sheet body,20g thick. the unit will have A top feeding tray & a housing of stainless steel casting With grinding plates & 3 type of meshes for variable type Of grinding requirements. The unit will be fitted with 1.0 hp single Phase electric

WORK TABLE support of pulverisor Size 1500X600X850mm Top & undershelf of s.s.sheet on m.s.anlge frame work & s.s.tubular legs, with adjustable feet. Top to have sound deadning material lining as required.

WORK TABLE WITH SINK for vegetable washing Size 1950x600x850+150 Top & Sink bowl of s.s.sheet, on s.s.anlge & s.s.tubular frame work with cross bracing at lower portion. Sink bowl will be integrally welded with top & grinded smooth. Sink bowl size 450x450x250mm.

CHOPPING BOARD for manual vegetable cutting size:- 1200X600X850mm Frame work made of s.s.anlge top will have P.P./Nylon Board for chopping 700x700x100mm chopping board.

VEGETABLE CUTTING MACHINE Aluminium casted body with ½ hp electric motor safety switch & double feed pusher for round flat & vertical shaped food items etc., the unit will be Table top model with easy to clean provision. Provided with 4 no cutting discs for slicing grating Dicing

CHAPPATI COLLECTION TABLE Size 1500X600X800 Top tray of 16G s.s.sheet, tray will have App.100mm ht. collor all around, mounted on s.s.tubular legs with adjustable feet & one s.s.sheet undershelf.

CHAPPATI ROLLING TABLE Size 2100x750x850mm Top & undershelf of s.s.sheet on m.s.anlge frame work & s.s.tubular legs, with adjustable feet. Top to have sound deadning material lining as required. THREE SIDE CROSS BRACING MADE OF S.S. PIPE 1" DIA FOR UNDERNEATH STORAGE.

CHAPPATI PLATE CUM PUFFER Size 1800x750x850mm Frame work of m.s.anlge, mounted on s.s.tubular legs frame work. All sides pannels & undershelf of s.s.sheet, top plate 10mm thick mild steel with cast iron puffing grills for puffing of chappaties. Complete with 'V' shape LPG burners with individual cont

EXHAUST HOOD (Without Ducting, Fixing & Extraction fan) for chapatti plate Size 1950x750x600mm Made of s.steel sheet, 20G thick duly welded & pop rivetted as required. The hood will be complete with s.s.sheet removable type baffle filters. Complete with greese collection channel & greese collection cup/s.

FOOD TROLLEY WITH 4 ROUND PANS, 1 RICE TRAY & STORAGE beneath O/S 1350X750X900mm S.S.Sheet insulated body, Frame work of m.s.anlge of size 38x38x5mm, mounted on 4 castors (2 with brakes) of size 150mm top to have cutout for 4nos. Round pans for Dal, Subzi etc. with 1 rice tray & storage below. Three side covered with s.s.sheet with s.

TRAY CARRIER TROLLEY Size 1200X600X1200mm S.S.Bottom base shelf mount at 150mm with all four sides turned down 50mm in 12mm and secured to welded s.s.anlge frame work & PROVIDED WITH THREE NOS. OF DETACHABLE TRAYS CUM SHELFS UNIT WILL BE MOUNTED ON 4" PILLAR TYPE CASTORS WHEELS (2 NOS. WITH BRAKE & 2 NOS. WITHOUT BRAKE)

TRAY SET UP COUNTER WITH BAIN MARIE & DOUBLE OVERSHELVES Size 1800x600x850+375+225 Top of 16G s.s.sheet, Bain Marie water tank of 18G s.s.sheet, fitted with 3.0kw heating element with automatic temperature controller. Water outlet provision with drain valve, 3 sides covered with 20G s.s.sheet, Top to accommodate s.s.sheet Food Pans with GN pan 1x2x4" depth with lid 5 sets.

STORAGE CABINET Size 1200X600X850mm Top of 16Swg S.S.Sheet one over shelf, three sides of 20SWG s.s. sheet. Dish storage cabinet with 2 shelves and sliding door will be provided on service side.

STORAGE RACK Size 900X450X1800 Vertical of 32 mm dia stainless steel pipe with adjustable feet 4 no of 18 S.S Sheet at equaly distance.

INGREDIENT BINS Size 600X600X600mm Made of S.S. 18 SWG WITH TOP HINGE OPENABLE DOORS SUPPORT WITH FOUR NOS. OF CASTORS, anti crack body, top half hinged lid. Provided with a scoop.

DUNNAGE RACK Size 1200X600X500mm Made of s.s.square pipes of size 32x32mm, with support of 25mm square s.s.pipe.

DIGITAL WEIGHING SCALE CAP. 300KG

POT RACK-3 TIER Size 1200X600X1500mm Verticals of 32mmX32mm square s.s.pipe, 3 shelves welded with vertical frame of 19mm dia s.s.pipe shelves with equal space between two tubes mounted on adjustable feet.

SOILED DISH LANDING TABLE WITH GARBAGE CHUTE Size 2400x600x850mm Top of 16G s.s.sheet with 'Sunkun' top. A garbage chute provided on top with a space below to keep dust bin (Not part of equipment). The top will be mounted on m.s.anlge, rust proof painted & s.s.vertical tubular legs with cross bracing support on 3 sides

THREE SINK UNIT Size 1800x600x850+150mm Top & 3 sink bowls of 16G s.s.sheet. Duly welded, grinded & polished smooth mounted on m.s.anlge & s.s.tubular frame work with 150mm back splash. Each Sink Bowl Size 500x500x300mm (without sanitory fittings)

CLEAN DISH TABLE Size 2100x600x850mm Specification same as that of work table but with 2 undershelves.

CLEAN DISH RACK Size 900x450x1800mm Vertical of 32 mm dia stainless steel pipe with adjustable feet 5 no vertical at equal distance 1st shelf fixed at 150mm from floor level.

pot stacking platform for heavy pot storage Size 1500x750x150mm S.S Palate frame will be made of 1.5” S.S Square pipe with adjustable bullet feet. And shelf will be made of 2”x3mm S.S Flat Patti.

masala trolley Size 600x600x750mm

plateform trolley Size 900X600X900mm Structure will be made of 40x40x5mm duly painted with rust proof paint. Top will be made of 10 SWG. M.S Sheet. 6” high moving wheel (02 Break + 02 Moving)

PRE WASH SINK UNIT Size 1800x750x850+150 Top & Sink bowl of s.s.sheet, on s.s.anlge & s.s.tubular frame work with cross bracing at lower portion. Sink bowl will be integrally welded with top & grinded smooth. Sink bowl size 450x450x250mm.

HOOD TYPE COMMERCIAL DISHWASHER Cap. 40-50 Racks per Hr. CYCLE TIME TOTAL/RINSE (SEC) 60-120-180/20 BASKET SIZE 500X500 MM WATER CONSUMPTION 3L/CYCLE TANK CAPACITY 20L RINSE CAPACITY 12L WASH PUMP 1.1KW WASH TANK 3KW RINSE TANK 8KW MAXIMUM USED POWER 9.1 WATER HARDNESS 70-140 PPM WATER PRESSURE 2-4 BAR POWER SUPPLY 400/3+N-/50

DIRTY DISH UNLOADING TABLE Size 1500x600x850mm Top of stainless steel sheet, mounted on m.s.angle & stainless steel tubular frame work. One 18g thick stainless steel sheet bottom Shelf will be fitted on table at a ht dia 150mm from floor.

CLEAN DISH TABLE Size 2100x750x850mm Specification same as that of work table but with 2 undershelves.

COLD ROOM SECTION WALK IN CHILLER CUM FREEZER External Room Dimensions : 3600X3000mm CHILLER Room Temperature - (+ 2°C to 8 °C) Product Entering Temp - + 30°C Pull Down Time - 15hrs. Product Loading - App.550kg./24hrs. Wall & Ceiling Panels Insulation - 80mm thick Prefabricated RPUF Panels Floor Panel Insulation - 80mm thick RPUF Panels with layer of Tarfelt sheet on both sides. Panel Finish - Internal :PCGI , External: PCGI Refrigerant -R-22 No. of Units - 1 (MAKE:- KIRLOSKAR/TECUMSEH/CARRIER Connected Load - 2.5 KW

ALUMINIUM RACK FOR COLD ROOM Size 1100X500X1500 Vertical of 50x50x5mm aluminium angle with adjustable feet 4 no of 18 swg. Sheet perforated aluminium shelves..

ALUMINIUM PALLET FOR COLD ROOM STORAGE Size 1500X450X150MM Top made of 16 swg aluminum sheet placed with s.s. angle 35x35x4 frame work with adjustable bullet feet.

L.P.G GAS PIPE LINE (200 RUNNING FEET APPROX) ACTUAL MEASUREMENT WILL BE ACCORDING TO As per site conditions

CENTRIFUGAL EXHAUST BLOWER 20000 CFM

S.S GRATING for kitchen drainage trough (APPROX 40 RUNNING FEET) ACTUAL MEASUREMENT WILL BE ACCORDING TO As per site conditions

EXHAUST HOOD DUCTING (APPROX 2000 SQUARE FEET) ACTUAL MEASUREMENT WILL BE ACCORDING TO As per site conditions

M.S CYLINDER BANK 120"X36”X42” (ACCESSORIES ARE NOT INCLUDED) Totally constructed in MS angle base of 40x40x5 mm supported with 12mm square wrought iron bars. Front doors are provided along with the locking arrangements made up of 18 SWG CR sheet is duly premiered and painted to prevent from rust etc.

BIOMEDICAL WASTE MATERIAL MANAGEMENT (As per Specifications) Solid Waste Treatment Plant (for incinerable waste) Incinerator (Oil fired, 50kg/hr capacity) for Biomedical Solid Waste Management along with a dedicated ETP including related Civil, Electrical and Mechanical works Solid Waste Treatment Plant (for non-incinerable waste) Autoclave for bio-medical waste of 500 ltr capacity Shredder for bio-medical waste infrastructure such as air compressor, RO Plant, office furniture, computer etc. for main and stand by units Liquid Waste Treatment Plant Design, engineering, supply, installation and commissioning of- (I) 2(two) Nos. 150KLD STP, (II) 1(one) No. 10 KLD ETP for OT& laboratory washing and (III) 1(one) No. 500 ltrs/day ETP for SWTP washing

SIGNAGES INTERNAL DIRECTIONAL wall Mounted Fabrication of Direction Sign wall Mounted with ss studs. Text using reverse HP Latex UV Print on 3M clear media and 3M 3630 scotchcal and pasting on 8mm. Floor numbering using 6mm Plexiglas CNC Laser Cut and Pasted using 3M VHB. Non lit

External DIRECTIONAL Ceiling Hung signs in corridor Fabrication of Direction Sign Ceiling Suspended using 50mm Cosign (Belgium) Anodised Profile with PU Paint. Text using reverse HP Latex UV Print on 3M clear media and 3M 3630 scotchcal and pasting on 4mm Plexiglas UV treated with 3M VHB. Floor numbering using 6mm Plexiglas CNC Laser Cut and Pasted using 3M VHB. Sign mounted with SS Chrome hollow pipe and thread rod and hilti fastener. Non lit

AREA ID (FACILITY) wall Mounted Fabrication of Direction Sign wall Mounted with ss studs. Text using reverse HP Latex UV Print on 3M clear media and 3M 3630 scotchcal and pasting on 8mm. Floor numbering using 6mm Plexiglas CNC Laser Cut and Pasted using 3M VHB. Non lit

FLOOR DIRECTORY (At Reception) WALL MOUNTED Fabrication of Floor Directory Sign .Text using HP Latex UV Print on 3M clear media and 3M 3630 scotchcal and pasting on 3mm Plexiglas UV treated with 3M VHB. Sandwitch top layer using 6mm Plexiglas. Sign mounted with SS Studs.

FLOOR DIRECTORY WALL MOUNTED Fabrication of Floor Directory Sign .Text using HP Latex UV Print on 3M clear media and 3M 3630 scotchcal and pasting on 3mm Plexiglas UV treated with 3M VHB. Sandwitch top layer using 6mm Plexiglas. Sign mounted with SS Studs.

AREA ID (FACILITY) PROJECTED Fabrication of Area ID Projected Sign using 50mm Cosign (Belgium) Anodised Profile with PU Paint. Text using reverse HP Latex UV Print on 3M clear media and 3M 3630 scotchcal and pasting on 4mm Plexiglas UV treated with 3M VHB. Floor numbering using 6mm Plexiglas CNC Laser Cut and Pasted using 3M VHB. Sign mounted with base plate and hilti fasteners. Non lit

ROOM ID Wall MOUNTED Fabrication of Room ID Sign .Text using reverse HP Latex UV Print on 3M clear media and 3M 3630 scotchcal and pasting on 8mm Plexiglas UV treated.Sign fixed with SS Profile and SS Screws.

Washroom PROJECTED Fabrication of Washroom Projected Sign using 50mm Cosign (Belgium) Anodised Profile with PU Paint. Text using reverse HP Latex UV Print on 3M clear media and 3M 3630 scotchcal and pasting on 4mm Plexiglas UV treated with 3M VHB. Picto using 6mm Plexiglas CNC Laser Cut and Pasted using 3M VHB. Sign mounted with SS fixtures.

FIRE EXIT DOOR MOUNTED Fabrication of Fire Exit Sign using UV treated 4mm plexiglas and photoluminiscent glow in the dark film application. Text and Picto using 3M scotchcal CNC Plotter cut and pasted. Sign mounted using Chrome fixtures.

STAIRS WALL MOUNTED Fabrication of Stairs Sign using UV treated 4mm plexiglas and photoluminiscent glow in the dark film application. Text and Picto using 3M scotchcal CNC Plotter cut and pasted. Sign mounted using Chrome fixtures.

LEVEL WALL MOUNTED Fabrication of Level Sign using UV treated 4mm plexiglas and photoluminiscent glow in the dark film application. Text and Picto using 3M scotchcal CNC Plotter cut and pasted. Sign mounted using Chrome fixtures.

CAUTIONARY WALL MOUNTED Fabrication of Cautionary Sign using UV treated 4mm plexiglas . Text and Picto using 3M scotchcal CNC Plotter cut and pasted. Sign mounted using Chrome fixtures.

NO SMOKING STATUTORY SIGN -NON LIT, WALL MOUNTED, SS ETCHING Fabrication of Cautionary Sign using UV treated 4mm plexiglas . Text and Picto using 3M scotchcal CNC Plotter cut and pasted. Sign mounted using Chrome fixtures.

BOH WALL MOUNTED Fabrication of BOH wall Sign using 316 grade SS chemically etched and color filled. Sign mounted using base of 2mm clear acrylic and 3M VHB.

FAÇADE LETTERS (Logo & Name at Entry - LL) WALL MOUNTED External Entry Level Facade Sign: Fabrication & Supply of External Entry Level Sign Logo made of 1mm Hairline finish SS 304 Grade ) for side returns by CNC Laser Cutting and welding and back and Altuglas facia with 3M 3630 series scothcal vinyl and fixing using allen screws made of SS.The facia to be sealed using Let - R-edge Jewelite trim cap to avoid dust and water from seaping into sign. Illumination using Samsung GOQ LED Modules frosted with 1.08 W power output. LED Drivers of Union Korea make with IP 68 rating ROHC & CE Certified. Sign Letters made of of 1.5mm Hairline finish SS 304 Grade for side returns and back and Casocryl (France ) facia for day time black and night time white effect upon illumination. The facia to be sealed using Let - R-edge Jewelite trim cap to avoid dust and water from seaping into sign. Illumination using Samsung GOQ LED Modules frosted with 1.08 W power output. LED Drivers of Union Korea make with IP 68 rating ROHC & CE Certified. BACK LIT - Day - Black/Night - White/Red Logo

LL Backlit Letters - ACCIDENT & EMERGENCY - WALL FIXED ACCIDENT & EMERGENCY Facade Sign: Fabrication & Supply of External Entry Level Sign made of 1mm Hairline finish SS 304 Grade for side returns by CNC Laser Cutting and welding and back and Altuglas facia with 3M 3630 series scothcal vinyl and fixing using allen screws made of SS.The facia to be sealed using Let - R-edge Jewelite trim cap to avoid dust and water from seaping into sign. Illumination using Samsung GOQ LED Modules frosted with 1.08 W power output. LED Drivers of Union Korea make with IP 68 rating ROHC & CE Certified.. BACK LIT - Day - Red/Night - Red

RECEPTION LETTERS WITH RED LOGO & LETTERS - WALL FIXED Word RECEPTION AND LOGO will be laser cut in 20 mm thick Plexiglass sheet with PU Painted, Reverse Mechanical Fixing and black Painted same as colours, Non Illuminated

FL EVAC Plate. WALL FIXED Fabrication of Floor Evacuation plan using UV treated 4mm plexiglas HP Latex UV reverse print on 3M clear film and photoluminiscentglow in the dark film mounted from behind. Sign fixed using SS fixtures/3M VHB

2 Sided Totem - GROUND FIXED External Directional Sign Double Sided : Fabrication & Supply of Totem sign made 0f 50x50x3 SHS internal frame and CNC Routed Aluminium cladding (no MS/GI to be used due to corrosion issues). Logo made of 1mm Hairline finish SS 304 Grade for side returns by CNC Laser cutting and welding and back and Altuglas facia with 3M 3630 series scothcal vinyl and fixing using allen screws made of SS. Illumination using Samsung GOQ LED Modules frosted with 1.08 W power output. LED Drivers of Union Korea make with IP 68 rating ROHC & CE Certified. Sign Letters made of of 1.5mm Hairline finish SS 304 Grade for side returns and back by CNC Laser Cutting and welding and Casocryl (France ) facia for day time black and night time white effect upon illumination. Illumination using Samsung GOQ LED Modules frosted with 1.08 W power output. LED Drivers of Union Korea make with IP 68 rating ROHC & CE Certified. The red area text using 12mm 010 Acrylic Push Thru Lettering with CNC Router and Illumination using LEDs and PU Automotive paint. Base made of SS 304 Grade and fixing on MS frame with 3M VHB and no screws to be visible. Sign fixed to the civil foundation using 16mm Base plate and Hilti Chemical Fasteners.

Cautionary Totems - GROUND FIXED Entry/Exit/Drop Off Sign: Fabrication & Supply of Entry/Exit/Drop Off sign made 0f 25x40x3 SHS internal frame and CNC Routed Aluminium cladding (no MS/GI to be used due to corrosion issues). The red area text using 12mm 010 Acrylic Push Thru Lettering with CNC Router and Illumination using LEDs and PU Automotive paint. Whote area text using Altuglas/Casocryl for day time black and night time white effect and illumination using LEDs. Aluminium to be CNC routed. Sign fixed to the civil foundation using 12mm Base plate and Hilti Chemical Fasteners.

Any other unseen item of work which are not covered in this BOQ that may be required at site during execution having an estimated provision of Rs.40,00,000.00. The rate for the items will be finaliased as per current APWD SOR in proportion to the quoted amount and the estimated amount.

NCC Limited