CONSTRUCTICONSTRUCTION OF IGLOOS URPS ESH AND ALLIED INFRASTRUCTURE AT SURATGARH ON EPC MODE.

Lump sum price worked out by the tenderer for “BUILDING WORK" as listed in Schedule ‘A’ Part - I

Subtotal

Lump sum price worked out by the tenderer for “INTERNAL ELECTRIFICATION WORK" as listed in Schedule ‘A’ Part - II

Subtotal

Lump sum price worked out by the tenderer for “ROAD , PATH & CULVERTS WORKS" as listed in Schedule ‘A’ Part - III

Subtotal

Lump sum price worked out by the tenderer for “AREA DRAINAGE WORKS" as listed in Schedule ‘A’ Part -IV

Subtotal

Lump sum price worked out by the tenderer for “EXTERNAL WATER SUPPLY" as listed in Schedule ‘A’ Part -V

Subtotal

Lump sum price worked out by the tenderer for “SITE CLEARANCE & DEVELOPMENT, EXCAVATION AND EARTHWORK WORKS" as listed in Schedule ‘A’ Part -VI

Subtotal

Lump sum price worked out by the tenderer for “EXTERNAL ELECTRIC SUPPLY WORKS" as listed in Schedule ‘A’ Part -VII

Subtotal

Lump sum price worked out by the tenderer for “LIGHTENING PROTECTION WORKS" as listed in Schedule ‘A’ Part -VIII

Subtotal

Schedule ‘A’ Part -IX MISCELLANEOUS WORKS

Supply and fixing flush to wall surface CMRI certified flame proof distribution board of die cast aluminium alloy (LM-6) gas group IIA, IIB, & IIC, SPN 8 way, 230 volts grade, suitable for fixing in & including MCB SPN 32 Amps, 10 kA- 01 No(Incomig) and MCB SP 6 Amps 10kA - 06 Nos ( outgoing) complete all as specified and as directed by Engr-in-charge.

Supply and fixing flush to wall surface CMRI certified flame proof distribution board of die cast aluminium alloy (LM-6) gas group IIA, IIB, & IIC, SPN 10 way, 230 volts grade, suitable for fixing in & including MCB SPN 32 Amps, 10 kA- 01 No(Incomig) and MCB SP 6 Amps 10kA - 08 Nos ( outgoing) complete all as specified and as directed by Engr-in-charge.

Supply and fixing flush to wall surface CMRI certified flame proof distribution board of die cast aluminium alloy (LM-6) gas group IIA, IIB, & IIC, SPN 12 way, 230 volts grade, suitable for fixing in & including MCB SPN 32 Amps, 10 kA- 01 No(Incomig) and MCB SP 6 Amps 10kA - 10 Nos ( outgoing) complete all as specified and as directed by Engr-in-charge.

Supply and fixing flame proof junction box LM 6 protection, 4 way including accessories suitable for 20 mm ERW pipe in wiring complete all as specified as directed by Engr-in-charge.

Supply and fixing flame proof junction box LM 6 protection, 3 way including accessories suitable for 20 mm ERW pipe in wiring complete all as specified as directed by Engr-in-charge.

Supplying, laying, jointing and testing in repair 100 mm bore, centrifugally cast (Spun) ductile iron pressure pipe with spigot and socketed ends, class K-7, ISI marked, confirming to IS: 8329/2000 blast furnace slag cement with portland cement properties suitable for rubber gasket jointing / tyton joints inclduing rubber gasket for joint and laid on floor/ in trenches. Note :- (i) Rate inlcudes the cost of rubber gasket for joints. (ii) DI fittings shall be measured and paid separately.

Cutting existing CI/DI Pipe line upto 100 mm including insertion of fittings, reducer, union, etc for new water connection as specified and directed. Note: Rate includes all fittings required for connections.

M&L for construction of brick masonry valve pit of size 120cm x 120cm x 120cm (internal dimensions of chamber) made with sub class 'B' old size clay bricks compresive strength not less than 75 Kg/sqcm in cement mortar 1:6 for sluice valve/gate valve and angle iron frame with front opening cover made of MS sheet 3.15 mm thick with handle, locking arrangement and PCC type B1 (1:2:4 with 20 mm graded stone aggregate) including necessary excavation, foundation concrete in PCC 1:3:6 type C1 (20 mm graded stone aggregate) and inside plastering with cement mortar 1:4 12 mm thick finished with a floating coat of neat cement PCC coping type B1 (1:2:4 with 20 mm graded stone aggregate) complete.

S&F DI/CI fittings (ISI marked) for flanged pipe/spigot socketd pipes upto 150mm bore such as bends, tee any type. Tapers and angle/radius and straight connecting pieeces

Factory assembled hut type double door type with cable alloy outdoor LT panel suitable for 3 phase, fabricated out of CRCA sheet 3.15mm thick MS sheet tapered, drip proof, top extended 100 mm on all sides including MS angle iron base frame of size 50x50x6mm thick duly welded with the following mountings/accessories & having individual compartment for switch gear connected and inter conneciton and painting with epoxy based primer and two coats of synthetic enamel paint with control wiring, suitable size bus bar and locking arrangement etc complete.

MCB 4 pole 40 Amp, 415 volt, 10KA , 01 Nos (Incomer)

MCB TPN 32 Amp, 415 volt, 10KA - 08 Nos

Indication lamp with LED type

Factory assembled hut type double door type with cable alloy outdoor LT panel suitable for 3 phase, fabricated out of CRCA sheet 3.15mm thick MS sheet tapered, drip proofv, top extended 100 mm on all sides including MS angle iron base frame of size 50x50x6mm thick duly welded with the following mountings/accessories & having individual compartment for switch gear connected and inter conneciton and painting with epoxy based primer and two coats of synthetic enamel paint with control wiring, suitable size bus bar and locking arrangement etc complete.

MCB 4 pole 40 Amp, 415 volt, 10KA , 01 Nos (Incomer)

MCB TPN 32 Amp, 415 volt, 10KA - 02 Nos

Indication lamp with LED type

Supply and Fix MCCB TPN 63 Amp, 415 volt, 10 KA, complete all as directed.

M&L for dry sand (Tibba sand) and punning for cushioning to underground cable complete all as specified and directed by Engineer-in-charge., Note: - For payment purpose thickness after punning shall be measured.

ALMIRAH SMALL STEEL : The base shall be made of two Numbers mild steel sheet channel basis made in U-shape with ends covered mild steel shall be 1 mm thick. The base channel shall be welded at 50 mm from each end of the length of 920 mm and shall be put to full width of 485 mm and shall be 100 mm high. Top, sides, bottom and back of almirah shall be of 1 mm thick mild steel sheet : Four shelves equally spaced of 1 mm thick mild steel sheet shall be provided to make five compartments. Front shutter shall have two leaves of equal size. One stainless steel handle of approved partern as approved by Engr-in-Charge with a locking device shall be provided as shown on drawing. The locking device shall be three way locking device with lock. Front shutter leaves shall have three butt hinges of 75 mm fixed to each shutter and shall be side hung. All joints and welding and fixing shall be done in accordance with the standard workmanship. All steel surfaces internally and externally exposed to view when placed in position shall be given tow coats of synteetic enamel paint over a coat of red oxide primer after preparation of steeel surfaces when ever working of painting shall be feasible. Painting shall be done with spray machine. All other work as specified and as shown on drg No FD-1032.

CHAIR CB STEEL WITH ARMS: Overall size shall be 535mm wide, 560mm deeep and 900mm high. Seat shall be 455mm high from floor. Conduit pipe used for frame shall be 20mm dia steeel tubing having wall thickness 1.6mm. Welding of frame where required shall be as directed and in running welding grinded to give smooth surface. Wood for seand and back, where caning is to be done shall be first class hard wood. Wood for handless shall be of hard wood. Weaving of cane shall be done with plastic cane in Godrej pattern. Cane shall be 2mm wide and 0.4 mm thick. Wood surfaces of seat, back and handles shall be painted dwith high glass paint, black in tint, before caning. Painting shall be done with spray machine after preparation of wooden surfaces. All wooden surface exposd to direct view when placed in position shall be painted with two coats of enamel paint over a coat of primer aftr preparation of surfaces. Painting shall be done with spray machine to achieve smooth surfaces. Bottom of legs shall have hard rubber shoes. Flat iron strips 20mmX3mm two numbers in each seat and back shall be welded to frame of chair as directed. Rest all as shown on drawing No FD-75(M).

TABLE OFFICE CLERK STEEL: Overall size shall be 122mm long610mm wide and 760mm high steel frame of overall size shall b 1160mm long, 570mm wide and 742mm high. Four legs of 25mm square mild steel tube of 1.6mm wall thickness shall be provided all as shown on drawing. Top of legs shall be joined together with 25mm square mild steel tube of 1.6mm wall thickness in long and short sides. Two short stiffeners of 25mm square mild steel tube of 1.6mm wall thickness shall be provided at 130mm from bottom of legs. One long stiffner of joining short stiffeners. Theree drawers of equal size shall be provided on the right hand side above th stiffeners at 130mm high with overall size of 350mm wide and 430mm high and 410mm deep irrespective of whatsover shown in drawing and specified in note 7 of the drawing the top of table shall be 18mm thick prelaminat3ed MDF Board with wood edging all round the top of table. Hard rubber/PVC toes shall be provided to the legs. Locking device shall be proveded to drawers. All steel surfaces exposed to view when placed in position shall be given twocoats of synthetic enamel paint over a coat of red oxide primer with spray machine after preparation of surfaces. Rest all as shown on drawing NO FD-1004.

Subtotal

Please Enable Macros to View BoQ information