SPECIAL REPAIR TO BLDG NO P-121 (OR MD ACCN) AT TPT LINE UNER GE GWALIOR

Amount

Demolition of cement concrete (unreinforced) in ground floor and paving not exceeding 15 cm thickness (below or above ground level) incl the disposal upto 50M complete all as specified and directed.

M&L for 25 mm thick cement concrete type B0, 1:2:4 (using 12.5mm graded stone aggregate) as in leveling course complete all as specified and directed.

Dismantling floor, hearth or wall tiling of any description and in any position including cement mortar bedding (but not backing) complete all as specified and directed.

M&L for non skid ceramic tiles, joint free, coloured tiles 7mm to 8 mm thick (Square or rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile laid over and including 15 mm thick screed bed or bedding layer of cement mortar (1:6) complete all as specified and directed.

M&L for ceramic tiles, joint free, coloured tiles 7mm to 8 mm mm thick as in skirting fixed over and including 10 mm thick cement screed in (1:4 ) CM set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles complete all as specified and directed.

M&L for 40 mm thick cement concrete type B-1, 1:2:4 (using 20mm graded stone aggregate ) as in floors, laid in panels and finished even & smooth with using extra cement complete all as specified and directed.

Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement plaster 1:6, finished even and smooth (without using extra lime or cement) complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement plaster 1:4 and mixed with WPC , finished even and smooth (without using extra lime or cement) complete all as specified and directed. (Note:- WPC shall be measured & paid seperately).

M&L for rendering 5 mm thick on faces or brick work ,concrete surfaces, in ceiling & sunkan floor etc, finished even and smooth (without using extra lime or cement) complete all as specified and directed.

Supply only water proofing compound complete all as specified and directed.

M&L for glazed ceramic coloured tiles in vertical surface 350mm x 250mm x 7mm/ 450 x 350 x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match, aid over and including rendering 10 mm thick on fair faces brick work or concrete surface in cement plaster 1:4 complete all as specified and directed.

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L for Brickwork with fly ash bricks old size, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

M&L for brick work with fly ash old size bricks, straight or curved on plan to any radius in half brick thick walls built in Cement Mortar 1.4 complete all as specified and directed.

M&L for preparation of new plaster surfaces of wall, applying wall putty on walls and applying two coat of oil emulsion over a coat of primer complete all as specified.

M&L for preparation of new plastered ceiling surface and applying three coats of white wash complete all as specified and directed.

M&L for prepration of new plastered surfaces of walls and applying two coats of weather proof water based emulsion paint ( Acrylic paint exterior grade) over a coat of Acrylic primer and including filling depression etc. complete all as specified and directed.

Dismantling of stone slab and tiles of any description or thickness in floor, aprons etc laid dry and pointed in any mortar complete all as specified and directed.

M&L for machine cut kota stone flooring 18 to 20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for screed bed or bedding layer of mortar 20 mm thick for laying floor finishes in cement plaster 1:6, complete all as specified and directed.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in any type of soil including removing to a distance not exceeding 50M complete all as specified and directed.

M&L for moorum/red bajri filling in floors or pavings, laid in layers not exceeding 15cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M&L for hard core of broken stone or boulders guage not exceeding 63mm deposited, spread and leveled in layers not exceeding 15cm thick and rammed to a true surface complete all as specified and directed.

M&L for cement concrete type E2 1:5:10 (using 40mm graded stone aggregate) as in sub base of floor or sunken floor etc complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C-2 using 20mm graded stone aggrtegate as in plinth protection/path and the like including finsihing even & fair complete all as specified and directed.

Taking down steel tubing and connection 15 mm bore incl cleaning for refixing or removing from site complete all as specified and directed.

Taking down steel tubing and connection 20 mm bore incl cleaning for refixing or removing from site complete all as specified and directed.

M&L for GI tubing 15mm dia medium grade galvanised with all fittings fixed to wall and floor complete all as specified and directed.

M&L for GI tubing 20 mm dia medium grade galvanised with all fittings fixed to wall and floor complete all as specified and directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, shelves, lintels, etc, and cutting chases for concealed water tubings or conduit wiring, etc and making good, cutting not exceeding 10cm girth on Brick walls complete all as specified and directed.

S&F in repair PVC (SWR) floor trap, plain with grating including jointing with solvent cement and fixed 75mm dia outlet complete all as specified and directed.

S&F in repair 15mm bore bib taps, fancy type chromium plated cast copper alloy with capaston head handle, screwed down screwed iron pipe or for brass ferule fixed, complete all as specified and directed.

S&F in repair Stop valve, cast copper alloy, screwed down, high pressure, with capston headed handle chromium plated concealed type screwed both ends for iron pipe 15mm bore or for unions complete all as specified and directed.

S&F in repair Stop valve, cast copper alloy, screwed down high pressure with capston headed handle chromium plated angular type screwed both ends for iron pipe 15mm bore or for unions and fixed complete all as specified and directed.

S&F in repair PVC connection 15mm size with PTMT nuts on both ends of length 450 mm complete all as specified and directed.

S&F in repair swivel shower of brass chromium plated of size 125mm for fixing with 15mm bore pipe complete all as specified and directed.

S&F in repair tabular towel rail, 20 mm dia, D type, 60 cm long between flanges, complete all as specified and directed.

S&F in repairs grating 100/125 mm dia of PTMT, fixed to Nahani trap complete all as specified and directed.

S&F in repair stainless steel kitchen plate rack made out of 0.63mm thick stainless steel of size 900x750 mm including screws and wt not less than 5.00 Kg complete all as specified and directed.

S&F in repair kitchen sinks made of stainless steel with drainage board 1mm thick with plug, washers, wastes, including fixing (cantilever brackets and connecting union to pipe overall size 915mm x 460mm boul size 410mm x 330mm x 160mm) complete all as specified and directed.

S&F in repair wash hand basin vitreous china (flat back) of size 550 x 400 mm excluding taps, waste, chain and plug and porcelain stopper but including brackets cutting for and pinning in ends complete all as specified and directed.

S&F in repair 32 mm waste fittings, brass chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly -nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

S&F in repair 15mm dia pillar taps fancy type, cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without lettered "Hot or Cold" with long screwed shanks and fly -nuts, screwed for iron pipe and fixed complete all as specified and directed.

Dismaintling of water tank exceeding 250 Ltrs but not exceeding 500 Ltrs complete all as specified and directed.

S&F for rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of capacity 500 litres hoisted and fixed in position all as specified in SSR Part-I, complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories), complete all as specified and directed.

S&F 110 mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls, complete all as specified and directed.

S&F 75 mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls, complete all as specified and directed.

S&F 75 mm PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed.

S&F PVC (SWR) bends any radius, 110mm bore, complete all as specified and directed.

S&F PVC (SWR) bends any radius, 75mm bore, complete all as specified and directed.

S&F PVC (SWR) junction single (single T), equal or unequal, 110mm bore, complete all as specified and directed.

S&F PVC (SWR) junction single (single T), equal or unequal, 75mm bore, complete all as specified and directed.

Taking down shutters of any description not exceeding 1 Sqm each and removing to or from store complete all as specified and directed.

Taking down shutters of any description exceeding 1 Sqm and n. exc 2 sqm each and removing to or from store complete all as specified and directed.

Refixing door shutter in same opening size exc 1 Sqm and n.exc 2 Sqm each complete all as specified and directed.

Refixing door shutter in same opening sizen. exc 1 Sqm each complete all as specified and directed.

Taking down chowkhat frame with shutter (without taking out shutter from the frame) n.exc 1.50 Sqm each complete all as specified and directed.

Taking down chowkhat frame with shutter (without taking out shutter from the frame) exc 1.50 Sqm but n exc 4 sqm each complete all as specified and directed.

S&F for solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S square tube, suppling & fixing in opening as per specification complete all as specified and directed.

S&F factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face, with particle board core S&F in frame at site as per specification complete all as specified and directed.

S&F for 150 mm aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F for extruded aluminium alloy handles 125 mm, fabricated type, anodised complete all as specified and directed.

S&F for 100 mm butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and directed.

S&F for 2nd class HW plain, solid, straight chowkhats and frames wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed.

S&F for 35 mm thick factory made shutter, Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F for 35mm thick factory made glazed and skelton shutters 2nd class HW open rebated and prepared to receive gauage (with sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred bead or security glass etc. Size of members of shutters as specified in IS-1003 supplied and fitted to chowkhats complete all as specified and directed.

All as per srl item 68 but 30mm thick devided into square with plain chamfered or rounded mitred and rounded rebated sash bars any numbers for window shutter complete all as specified and directed.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed.

S&F for 18 /19mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed.

S&F for continous (piano) hinges , mild steel, bright finished or electrogalvanised, width of flap 30mm complete all as specified and directed.

S&F 19/20mm thick block boards, grade 2 quality, interior grade, commercial type, fixed with screws to timber frame-work, complete all as specified and directed.

S&F for 75 mm Hasp & Staple, safety type, aluminium anodised hinge pin , including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F in repair 75 mm Hasp & Staple, safety type, aluminium anodised hinge pin , including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F MS framed work as in grill or framed guard bars with end of bars welded or riveted into spikes conforming to Fe- 290 Gde E-165 complete all as specified and directed.

M&L for mild steel work as in bands, straps, clamps, hold fasts, wall tiles, plain angle cleats for securing purlins to wood trusses or refters, and similar samll articles confirming to Fe- 290 Gde E-165 complete all as specified and directed.

S&F for steel ventilators with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frame/metal frames, glazed with putty or fixed with beads complete all as specified and directed.

S&F for 4 mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pan complete all as specified and directed.

S&F figured glass, pin head type 4mm thick and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified and directed.

S&F for galvanised mild steel wire cloth 0.46 nominal dia of wires and average width of aprature 1.18mm and fixed with tinned tacks galvanised wire staples fixed including a coat of french blue paints complete all as specified and directed.

S&F in repair galvanised mild steel wire cloth 0.46 nominal dia of wires and average width of aprature 1.18mm and fixed with tinned tacks , or galvanised wire staples fixed including complete all as specified and directed.

S&F for 100 mm butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and directed.

S&F for 50 mm butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and directed.

S&F alumunium handle cast type anodised 150mm long complete all as specified and directed.

S&F alumunium handle cast type anodised 125mm long complete all as specified and directed.

S&F 200mm long alumunium anodised barrel tower bolts of extructed section complete all as specified and directed.

S&F 150mm long alumunium anodised barrel tower bolts of extructed section complete all as specified and directed.

S&F aluminum alloy anodized sliding door bolt 300mm long with hasp and staple (bolt type) and fixing clip of sheet and cast in extruded section and fixing bolts and sliding bolt of extruded section complete all as specified and directed.

M&L for preparation of new wood or wood based surface of any description exceeding 10cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new steel surface of any description exceeding 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F for 20 mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed complete all as specified and directed.

M&L for preparation old surfaces of wall including, complete removal of existing treatment , and applying wall putty on walls and applying two coat oil emulsion over a coat of primer complete all as specified and directed.

M&L for preparing old decorated surfaces by brooming down, scrapping down smoke soot, moulds, moss and trading oil and greasy spots plastered and unplastered surfaces of ceiling and applying one coat of white wash complete all as specified and directed.

M&L for for applying one coat of synthetic enamel paint on old steel & iron surfaces (previously decorated) for grills, guard bars of any description not otherwise described over 10cm in width or girth including preparation of old surfaces complete all as specified and as directed.

M&L for cement concrete type D2 1:4:8 (using 40mm graded stone aggregate), as in sub base of floor complete all as specified and as directed.

M&L for cutting out cracks to V section in existing walls, roofing or terrace, cleaning out wetting grouting with cement and sand slurry 1:3 complete all as specified and directed.

M&L for reinforced cement concrete (Nominal Mix) type B-1 1:2:4 (using 20 mm graded stone aggregate) as bond of size 300 mm X 230 mm X75 mm thick complete all as specified and directed.

M&L for mild steel TMT bars ,10mm dia and over, cut to length bent to shape required including cranking bending spirally for hoping for coloumns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed.

M&L Granite (of any type) tiles 18 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete, laid over and including 15mm thick screed in CM 1:4 complete all as specified and directed.

S&F in repair fancy type vista patern curtain roads aluminium 20 mm dia with required colour powder coated of approved shade including bracket/joictions /wall to wall and with rings of best quality as approved by Engineer-in-Charge.

S&F for pressed steel frame of size 125 x 60 mm for door with one or more rebates makaing necessary fixing lugs,higes, lock strike plate, etc, complete, as specified, complete all as specified and directed.

S&F for pressed steel frame of size 105 x 60 mm for door with one or more rebates makaing necessary fixing lugs,higes, lock strike plate, etc, complete, as specified, complete all as specified and directed.

M&L for providing cement concrete type C1 1:3:6 ( using 20 mm graded aggregate) as filling inside pressed steel frame complete all as specified and directed.

M&L for preparing of old surfaces by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efforecent salt and trading oil and greasy spots plastered or un plastered surfaces of wall including cornices, pilasters etc. and applying one coat of cement base paint white or tinted complete all as specified and directed.

M&L for preparing old painted wood and wood based surfaces exceeding 10cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for applying treatment on exposed roof portion incl. beams, chajjas, slab etcas under- (a) Removing all loose concrete elements & applying acid wash & applying Cement slurry mixed with Nitobond/tapcrete all as spd (b) Inserting drilling holes in the wall /beam by 10mm dia bars & tuck welding with existing reinforcement @ 0.50m c/c ,nailing wire fabric 50x50 mm in the complete area all as spd (c) M& L 15 mm dubbing coat in CM1:2 mortar mixed with Nitobond /Tapcrete@ 2% by weight complete all as directed

M&L for provn of roof treatment with polymeric water proofing membrance with the following specification as under including taking down of existing roof treatment: (a) Applying a coat of bitumen primer conforming to IS 3384 @ 0.40 Itrs/sqm and allow to dry. (b) Applying and laying 3 mm thick APP having non- woven polyster matt at core and under surface coated with plastic polythene film, laid on primed surface, fixed with torch application method as per manufacturer instruction. (c) Screed bed 15mm thick in CM 1:4 as bedding layer using 100% coarse sand. (d) S&F for precast cement concrete tiles of size 250x250x25 mm conforming to IS 1237-1980 laid over screed bed and including joints filed with cement mortar 1:2 mixed with linseed oil @ 5% by weight of cement.

S&F in repair vitreous china squatting pan "(Orrissa" pattern) size 580 x 440mm white with integral foot rests (excluding flushing cistern and flush pipe ) complete all as specified and directed.

S&F in repair PVC flushing cistern 10 Ltrs capacity including all fitting flush pipe etc complete all as specified and directed.

M&L for 100 mm thick cement concrete type D-2 1:4:8 (using 40 mm graded stone aggregate), as in sub base for floor, finished even and rough complete all as specified and directed.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed

M&L for 60 mm thickness rubber moulded machine pressed precast concrete interlocking paver block M-35 any shape and size, confirming to IS 15658-2006 in grey cement glossy finish rubber mould casted laid dry over sand cushioning complete all as specified and directed.

M&L for rubber moulded chequered cement concrete tiles 250mm x 250mmx 25mm thick, set jointed and pointed in cement slurry in floors with grey cement and pigments complete all as directed including 15mm thick screed bed in CM 1:6 complete all as specifed and directed

M&L for cement concrete type B0 1:2:4 (Using 12.50 mm graded stone aggregate) mixed with Tapecrete/ Pidicrete/Nito Bond @ 1 Ltr/Bag of cement over chajja /window projection, of any description and in any position, including all necessary form work work as required, complete all as specified and directed

S&F for box type steel window with side hung shutters (double shutters for glass and gauze) joinnted together with and including grill using 10 mm square bars @ 10 cm C/C as per TD No CEBZ/TD/14/2011 including box type hunges with steel handle and steel peg stay complete with glazing bars devetailed and welded complete all as specified and as directed Note : Glass/gauge shall be measured and paid separately der respected item as supply and fix complete all as specified and directed.

M & L for Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators,sockets,light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed

M & L for point wiring with 1.5 sqmm (Nominal Area)PVC insulated FRLS un sheathed multi stranded copper conductor drawn in and including non metalic rigid PVC concealed conduit of med grade of suitable size with all fitings and accessories including factory made MS/ pressed steel terminal box with zinc coated duly concealed in wall including modular metal flush boxes reqd as per site reqmt for mounting switches, sockets fan regulators etc including continuous earth wire PVC insulated 1.5 Sq mm FRLS copper conductor connecting to common earth and earth dolly complete all as specified :- Make of Conduit :- Anchor/Modi/Presffit. Make of wire :- Finolex/Polycab/Plaza.

For one light point controlled by one switch complete all as specified and directed.

For one light point controlled by 2- two way switch complete all as specified and directed.

For one fan point controlled by one switch complete all as specified and directed.

One Bell/Buzzer point controlled by one way 5 Amp push button switch complete all as specified and directed.

For one 5 pin socket out let 5 amps on same bd complete all as specified and directed.

For one 5 pin socket out let 5 amps on independent board complete all as specified and directed.

All as per item No 120 here in before but with cable 2.5 sqmm (nominal area) multi stranded copper wire unsheathed for one 5 pin socket out let 15 amps on independent board including continuous earth wire PVC insulated 1.5 sqmm copper multistranded conductor connecting to common earth and earth dolly complete. Make of Conduit :- Anchor/Modi/Presffit. Make of wire :- Finolex/Polycab/Plaza.

Supply and fixing ceiling rose surface bakelite 3 terminals 65x50mm complete all as specified and directed. Make :- Leader/Legrand/Havells.

S & F modular white cover plate with frame of 12 module complete all as specified and directed. Make :- Leader/Legrand/Havells.

S & F modular white cover plate with frame of 06 module complete all as specified and directed. Make :- Leader/Legrand/Havells.

S & F modular white cover plate with frame of 03 module complete all as specified and directed. Make :- Leader/Legrand/Havells.

S & F modular white cover plate with frame of 02 module complete all as specified and directed. Make :- Leader/Legrand/Havells.

S&F Modular switch 1 way 06 amp single pole complete all as specified and directed. Make :- Leader/Legrand/Havells.

S&F Modular switch 2 way 06 amp single pole complete all as specified and directed. Make :- Leader/Legrand/Havells.

S & F modular switch socket combination 16A, 6 Pin of 3 module complete all as specified and directed. Make :- Leader/Legrand/Havells.

S & F of modular socket outlet 6A-5 pin combined of 02 module complete all as specified and directed. Make :- Leader/Legrand/Havells.

S & of moduar bell push 6 Amp 1 module complete all as specified and directed. Make :- Leader/Legrand/Havells.

S & F of modular fan step regulator 120 W-2 module complete all as specified and directed. Make :- Leader/Legrand/Havells.

S&F of buzzer Ding Dong, AC, 230 Volts, single pole complete all as specified and directed. Make :- Leader/Legrand/Havells.

S&F Lamp holder, PVC/polycarbonate type with back plate suitable for batten fittings incl LED Bulb 09W/10W complete. Make of Lamp Holder :- Leader/Legrand/Havells. Make of LED Bulb :- Philips, Wipro, Havells.

S& F decorative ultra slim square profile 2Ft LED batten of 9/10 W incluing req length of 1.5 Sqmm PVC multistranded copper conductor ro electrical connection from ceiling rose to connector of LED fitting including testing on completion all as specified and directed. Make :- Wipro, Philips.& Havells.

S&F decorative ultra slim square profile LED batten of 20/22 W incluing req length of 1.5 Sqmm PVC multistranded copper conductor ro electrical connection from ceiling rose to connector of LED fitting including testing on completion all as specified and directed. Make of LED fittings :- Philips, Wipro, Havells.

S & F security light fittings better optics for uniform distribution IP 65 protection LED of 30 watt, Heat resistance glass, pressure die cast aluminium housing including 25mm dia galvanised iron pipe light grade bracket bent to shape over all length 0.60mtr fixed to wall with 02 Nos FI clamps made of 40 x 6 mm FI, 15 cm long, 8 mm dia bolts and nuts with washers grouted in wall complete including reqd length of 1.5 Sqmm PVC multistranded copper conductor for connection from ceiling rose to light fittings incl testing on completion all as specified and directed. Make of LED fittings :- Philips, Wipro, Havells.

M & L for Taking down fan, sealing cable end, dismantling blades and removing fan and blades to store including painting with two coat of synthetic enamel paint over one caot of primr including wirting of MES No and refixing the same complete all as specified and directed.

Taking down submain wiring of any size any type and in any position metalic/non metallic PVC conduit of wooden batten complete all as specified and directed.

M&L, sub main wiring with two single core PVC insulated unsheathed FRLS multi stranded copper conductor (ISI marked with valid CML No), cable 1100 Volt grade, 6 sqmm size drawn in and including non metallic rigid PVC concealed conduit (ISI marked with valid CML No) not less than 25 mm dia with all fitting & fixing accessories including one run single core PVC insulated unsheathed 4 Sqmm FRLS copper conductor (ISI marked with valid CML No) colour code as a earth continuity and connected upto DB complete all as specified and directed. (NOTE: (i) Two run of single core PVC cable with one run of earth conductor and conduit shall be measured as one unit and the quoted rates shall be deemed to be inclusive for cutting chases in wall/pillars/columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface to match with the existing surface. Make of Conduit :- Anchor/Modi/Presffit. Make of wire :- Finolex/Polycab/Plaza.

Supply, install, commissioning and installation of distribution meter box indoor type, factory made out of CRCA sheet 2mm thick with angle iron 30x30x2 mm complete with inside, outside powder coated independed housing for meters with transperent glass & rubber gasket packing with suitable size copper single/ two core wire for each control, cable gland, with 200 Amp rated TPN aluminium busbar (for outgoing) duly insulated (including self insulated) maintaining proper space for each busbar and grouting panel in wall etc and making good the disturbed surface complete including with arrangement and including taking down the existing metal/PVC box comprising for following fittings:- (i) MCCB TPN, 63 Amps ,16 KA - 01 No (For incoming) (ii) Amp Meter (0-100 Amp)- 01 Nos Make :AE (iii) Volts Meter (0-500 Volts ) - 01 No Make :AE (iv) Indicator Lamp set of three R,Y,B - 01 Set (v) ASS & VSS with CTs -02 Nos ( 01 Each) (vi) MCB SP 40 Amps, 230 volts - 04 Nos (For outgoing) (vii) Nutral bus bar link mounted on insulator. (viii) Place for fixing the energy meter. - 04 Nos Note :- Taking down and refixing of the electric meters is deemed to included in the quoted rate. Make :- Schneider/Legrand/Seimens.

S&F, in repair, MCB DB, sheet metal enclosures double door SPN 8 way with 200 Amps rated bus bar 240 volts 2 in 1 shutter (METAL DOOR) type with blanking plates where required and IP 43 degree protection complete all as specified and directed. Make :- Schneider/Legrand/Seimens.

S&F, MCB SPN 40 Amps, 240 volts 'B' series 16 KA ,including connection with suitable size copper lugs complete all as specified and directed. Make :- Schneider/Legrand/Seimens.

S&F, MCB SP 240 volts, 6 to 32 Amps, 'B' series 10 KA including connection with suitable size copper lugs. complete all as specified and directed. Make :- Schneider/Legrand/Seimens.

Supplying, laying, testing and commissioning of XLPE insulated screened PVC bedded galvanised steel strip or wire armured electric power cable (Heavy duty ) with aluminium conductor 1100 volts grade, cross sectional area of 25 Sqmm 4 Core complete all as specified and directed.. Make :- Polycab/Finolex/KEI.

Excavation in trenches n exc. 1.5 m wide and n' exc. 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

Returning, filling of excavated soil, including spreading leveling, watering and well ramming in layers, not exceeding 25cm complete all as specified and directed.

Removing of surplus soil to a distance n exc 50 m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and directed.

M&L for sand filling in trenches with clean dry unwashed sand free from sharp particles, gently punning around the cables complete all as specified and directed.

M&L for bricks, old size sub class `B' laid in trenches with width wise along the alignment of the cable as protection complete all as specified and directed.

S&F tube 'Light' grade galvanised with all fitting laid in trenches, fixed to wall and floor of 50 mm dia for cable protection complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) vertically, with top edge of plate not less than 1.5 metre below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 of MES Schedule Part-I connecting to earthing test point & to main switch board and testing on completion with and including necessary excavation and earth work in any type soil, earth lead connected to earth test point & to main switch board etc with & including adequate quantity of charcoal dust and common salt, test point, PCC (1:3:6) type C-1 (using 20mm graded BT stone aggregate) for earth pit with 40 x 40 x 6mm mild steel angle iron frame for cover, internal surface of concrete shall be given 10mm thick plaster in CM 1:4, pre cast RCC (1:2:4) type B-1 (using 20mm graded BT stone aggregate) 40mm thick cover, reinforced with 8mm dia deformed or TMT bars 3 Nos both way with 12mm dia round bar handle, GI medium grade watering pipe 20 mm dia with funnel and wire mesh and 15mm dia GI medium grade earth lead protection pipe etc complete all as specified and directed.

lodhi builders

RAJ AND BROTHERS

M/s Anjali Construction

M/s J S & SONS

M/s. Varinder Kumar Sharma

somyaenterprises